TI CDC2509CPW

CDC2509C
3.3-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS620 – DECEMBER 1998
D
D
D
D
D
D
D
D
D
D
D
D
D
D
PW PACKAGE
(TOP VIEW)
Designed to Meet PC SDRAM Registered
DIMM Design Support Document Rev. 1.2
Spread Spectrum Clock Compatible
Operating Frequency 25 MHz to 125 MHz
Static tPhase Error Distribution at 66MHz to
100 MHz is ±150 ps
Drop-In Replacement for TI CDC2509A With
Enhanced Performance
Jitter (cyc – cyc) at 66 MHz to 100 MHz is
|100 ps|
Available in Plastic 24-Pin TSSOP
Phase-Lock Loop Clock Distribution for
Synchronous DRAM Applications
Distributes One Clock Input to One Bank of
Five and One Bank of Four Outputs
Separate Output Enable for Each Output
Bank
External Feedback (FBIN) Terminal Is Used
to Synchronize the Outputs to the Clock
Input
On-Chip Series Damping Resistors
No External RC Network Required
Operates at 3.3 V
AGND
VCC
1Y0
1Y1
1Y2
GND
GND
1Y3
1Y4
VCC
1G
FBOUT
1
24
2
23
3
22
4
21
5
20
6
19
7
18
8
17
9
16
10
15
11
14
12
13
CLK
AVCC
VCC
2Y0
2Y1
GND
GND
2Y2
2Y3
VCC
2G
FBIN
description
The CDC2509C is a high-performance, low-skew, low-jitter, phase-lock loop (PLL) clock driver. It uses a PLL
to precisely align, in both frequency and phase, the feedback (FBOUT) output to the clock (CLK) input signal.
It is specifically designed for use with synchronous DRAMs. The CDC2509C operates at 3.3 V VCC. It also
provides integrated series-damping resistors that make it ideal for driving point-to-point loads.
One bank of five outputs and one bank of four outputs provide nine low-skew, low-jitter copies of CLK. Output
signal duty cycles are adjusted to 50%, independent of the duty cycle at CLK. Each bank of outputs is enabled
or disabled separately via the control (1G and 2G) inputs. When the G inputs are high, the outputs switch in
phase and frequency with CLK; when the G inputs are low, the outputs are disabled to the logic-low state.
Unlike many products containing PLLs, the CDC2509C does not require external RC networks. The loop filter
for the PLL is included on-chip, minimizing component count, board space, and cost.
Because it is based on PLL circuitry, the CDC2509C requires a stabilization time to achieve phase lock of the
feedback signal to the reference signal. This stabilization time is required, following power up and application
of a fixed-frequency, fixed-phase signal at CLK, and following any changes to the PLL reference or feedback
signals. The PLL can be bypassed for test purposes by strapping AVCC to ground.
The CDC2509C is characterized for operation from 0°C to 85°C.
For application information refer to application reports High Speed Distribution Design Techniques for
CDC509/516/2509/2510/2516 (literature number SLMA003) and Using CDC2509A/2510A PLL with Spread
Spectrum Clocking (SSC) (literature number SCAA039).
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  1998, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
CDC2509C
3.3-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS620 – DECEMBER 1998
FUNCTION TABLE
INPUTS
OUTPUTS
1G
2G
CLK
1Y
(0:4)
2Y
(0:3)
FBOUT
X
X
L
L
L
L
L
L
H
L
L
H
L
H
H
L
H
H
H
L
H
H
L
H
H
H
H
H
H
H
functional block diagram
1G
11
3
4
5
8
9
2G
20
24
ÎÎÎÎÎÎÎ
ÁÁÁÁÁÁ
ÎÎÎÎÎÎÎ
ÁÁÁÁÁÁ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
PLL
FBIN
AVCC
13
23
AVAILABLE OPTIONS
PACKAGE
2
1Y1
1Y2
1Y3
1Y4
14
21
CLK
1Y0
TA
SMALL OUTLINE
(PW)
0°C to 85°C
CDC2509CPWR
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
16
12
2Y0
2Y1
2Y2
2Y3
FBOUT
CDC2509C
3.3-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS620 – DECEMBER 1998
Terminal Functions
TERMINAL
NAME
NO.
TYPE
DESCRIPTION
CLK
24
I
Clock input. CLK provides the clock signal to be distributed by the CDC2509C clock driver. CLK is used
to provide the reference signal to the integrated PLL that generates the clock output signals. CLK must
have a fixed frequency and fixed phase for the PLL to obtain phase lock. Once the circuit is powered
up and a valid CLK signal is applied, a stabilization time is required for the PLL to phase lock the
feedback signal to its reference signal.
FBIN
13
I
Feedback input. FBIN provides the feedback signal to the internal PLL. FBIN must be hard-wired to
FBOUT to complete the PLL. The integrated PLL synchronizes CLK and FBIN so that there is nominally
zero phase error between CLK and FBIN.
1G
11
I
Output bank enable. 1G is the output enable for outputs 1Y(0:4). When 1G is low, outputs 1Y(0:4) are
disabled to a logic-low state. When 1G is high, all outputs 1Y(0:4) are enabled and switch at the same
frequency as CLK.
2G
14
I
Output bank enable. 2G is the output enable for outputs 2Y(0:3). When 2G is low, outputs 2Y(0:3) are
disabled to a logic low state. When 2G is high, all outputs 2Y(0:3) are enabled and switch at the same
frequency as CLK.
FBOUT
12
O
Feedback output. FBOUT is dedicated for external feedback. It switches at the same frequency as CLK.
When externally wired to FBIN, FBOUT completes the feedback loop of the PLL. FBOUT has an
integrated 25-Ω series-damping resistor.
1Y (0:4)
3, 4, 5, 8, 9
O
Clock outputs. These outputs provide low-skew copies of CLK. Output bank 1Y(0:4) is enabled via the
1G input. These outputs can be disabled to a logic-low state by deasserting the 1G control input. Each
output has an integrated 25-Ω series-damping resistor.
2Y (0:3)
21, 20, 17, 16
O
Clock outputs. These outputs provide low-skew copies of CLK. Output bank 2Y(0:3) is enabled via the
2G input. These outputs can be disabled to a logic-low state by deasserting the 2G control input. Each
output has an integrated 25-Ω series-damping resistor.
AVCC
23
Power
Analog power supply. AVCC provides the power reference for the analog circuitry. In addition, AVCC can
be used to bypass the PLL for test purposes. When AVCC is strapped to ground, PLL is bypassed and
CLK is buffered directly to the device outputs.
AGND
1
Ground
Analog ground. AGND provides the ground reference for the analog circuitry.
VCC
GND
2, 10, 15, 22
Power
Power supply
6, 7, 18, 19
Ground
Ground
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
CDC2509C
3.3-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS620 – DECEMBER 1998
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, AVCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AVCC < VCC +0.7 V
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4.6 V
Input voltage range, VI (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 6.5 V
Voltage range applied to any output in the high or low state,
VO (see Notes 2 and 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V
Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA
Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA
Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA
Continuous current through each VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA
Maximum power dissipation at TA = 55°C (in still air) (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.7 W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. AVCC must not exceed VCC.
2. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
3. This value is limited to 4.6 V maximum.
4. The maximum package power dissipation is calculated using a junction temperature of 150°C and a board trace length of 750 mils.
For more information, refer to the Package Thermal Considerations application note in the ABT Advanced BiCMOS Technology Data
Book, literature number SCBD002.
recommended operating conditions (see Note 5)
VCC, AVCC Supply voltage
VIH
High-level input voltage
MIN
MAX
3
3.6
2
UNIT
V
V
VIL
VI
Low-level input voltage
0.8
IOH
IOL
High-level output current
VCC
–12
mA
Low-level output current
12
mA
85
°C
Input voltage
0
TA
Operating free-air temperature
NOTE 5: Unused inputs must be held high or low to prevent them from floating.
0
V
V
timing requirements over recommended ranges of supply voltage and operating free-air
temperature
fclk
Clock frequency
Input clock duty cycle
Stabilization time†
MIN
MAX
UNIT
25
125
MHz
40%
60%
1
ms
† Time required for the integrated PLL circuit to obtain phase lock of its feedback signal to its reference signal. For phase lock to be obtained, a
fixed-frequency, fixed-phase reference signal must be present at CLK. Until phase lock is obtained, the specifications for propagation delay, skew,
and jitter parameters given in the switching characteristics table are not applicable. This parameter does not apply for input modulation under
SSC application.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
CDC2509C
3.3-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS620 – DECEMBER 1998
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
VIK
Input clamp voltage
II = –18 mA
IOH = –100 µA
VOH
High-level output voltage
IOH = –12 mA
IOH = – 6 mA
VOL
Low-level output voltage
IOL = 100 µA
IOL = 12 mA
VCC, AVCC
3V
MIN
MIN to MAX
3V
VCC–0.2
2.1
3V
2.4
High-level output current
UNIT
–1.2
V
0.2
3V
0.8
3V
0.55
3.135 V
VO = 1.65 V
VO = 3.135 V
MAX
V
MIN to MAX
IOL = 6 mA
VO = 1 V
IOH
TYP‡
V
–32
3.3 V
mA
–36
3.465 V
–12
Low-level output current
VO = 1.95 V
VO = 1.65 V
3.135 V
IOL
34
14
Input current
VO = 0.4 V
VI = VCC or GND
3.465 V
II
3.6 V
±5
µA
3.6 V
10
µA
3.3 V to 3.6 V
500
µA
3.3 V
ICC§
Supply current
VI = VCC or GND,
Outputs: low or high
IO = 0,
∆ICC
Change in supply current
One input at VCC – 0.6 V,
Other inputs at VCC or GND
Ci
Input capacitance
VI = VCC or GND
VO = VCC or GND
mA
40
3.3 V
Co
Output capacitance
3.3 V
‡ For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
§ For ICC of AVCC, and ICC vs Frequency (see Figures 11 and 12).
4
pF
6
pF
switching characteristics over recommended ranges of supply voltage and operating free-air
temperature, CL = 30 pF (see Note 6 and Figures 1 and 2)‡
PARAMETER
Phase error time – static (normalized)
(See Figures 3 – 8)
tsk(o)
Output skew time§
FROM
(INPUT)/CONDITION
TO
(OUTPUT)
CLKIN↑ = 66 MHz to100 MHz
FBIN↑
Any Y or FBOUT
Any Y or FBOUT
Phase error time – jitter (see Note 7)
Jitter(cycle-cycle)
(See Figures 9 and 10)
Duty cycle
Any Y or FBOUT
Clkin = 66 MHz to 100 MHz
VCC, AVCC = 3.3 V
± 0.165 V
MIN
–150
–50
Any Y or FBOUT
TYP
UNIT
MAX
150
ps
200
ps
50
|100|
F(clkin > 60 MHz)
Any Y or FBOUT
45%
55%
ps
tr
Rise time (See Notes 8 and 9)
VO = 1.2 V to 1.8 V,
IBIS simulation
Any Y or FBOUT
2.5
1
V/ns
tf
Fall time (See Notes 8 and 9)
VO = 1.2 V to 1.8 V,
IBIS simulation
Any Y or FBOUT
2.5
1
V/ns
‡ These parameters are not production tested.
§ The tsk(o) specification is only valid for equal loading of all outputs.
NOTES: 6. The specifications for parameters in this table are applicable only after any appropriate stabilization time has elapsed.
7. Calculated per PC DRAM SPEC (tphase error, static – jitter(cycle-to-cycle)).
8. This is equivalent to 0.8 ns/2.5 ns and 0.8 ns/2.7 ns into standard 500 Ω/ 30 pf load for output swing of 04. V to 2 V.
9. 64 MB DIMM configuration according to PC SDRAM Registered DIMM Design Support Document, Figure 20 and Table 13.
Intel is a trademark of Intel Corporation.
PC SDRAM Register DIMM Design Support Document is published by Intel Corporation.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
CDC2509C
3.3-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS620 – DECEMBER 1998
PARAMETER MEASUREMENT INFORMATION
3V
Input
50% VCC
0V
tpd
From Output
Under Test
30 pF
500 W
Output
2V
0.4 V
tr
LOAD CIRCUIT FOR OUTPUTS
50% VCC
VOH
2V
0.4 V
VOL
tf
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
NOTES: A. CL includes probe and jig capacitance.
B. All input pulses are supplied by generators having the following characteristics: PRR ≤ 100 MHz, ZO = 50 Ω, tr ≤ 1.2 ns, tf ≤ 1.2 ns.
C. The outputs are measured one at a time with one transition per measurement.
Figure 1. Load Circuit and Voltage Waveforms
CLKIN
FBIN
tphase error
FBOUT
Any Y
tsk(o)
Any Y
Any Y
tsk(o)
Figure 2. Phase Error and Skew Calculations
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
CDC2509C
3.3-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS620 – DECEMBER 1998
TYPICAL CHARACTERISTICS
CDC2509C
PHASE ADJUSTMENT SLOPE AND PHASE ERROR
vs
LOAD CAPACITANCE
200
VCC = 3.3 V
fc = 100 MHz
C(LY) = 30pF
TA = 25°C
See Notes A and B
10
100
0
0
Phase Error
–10
–100
–20
–200
–30
Phase Error – ps
Phase Adjustment Slope – ps/pF
20
–300
Phase Adjustment Slope
–40
–400
0
5
10
15
20
25
30
35
40
45
50
C(LF) – Lumped Feedback Capacitance at FBIN – pF
Figure 3
CDC2509A
PHASE ADJUSTMENT SLOPE AND PHASE ERROR
vs
LOAD CAPACITANCE
100
VCC = 3.3 V
fc = 100 MHz
C(LY) = 30pF
TA = 25°C
See Notes A and B
0
0
–100
–10
Phase Error
–20
–200
–30
–300
–40
Phase Error – ps
Phase Adjustment Slope – ps/pF
10
–400
Phase
Adjustment Slope
–50
–500
0
5
10
15
20
25
30
35
40
45
50
C(LF) – Lumped Feedback Capacitance at FBIN – pF
Figure 4
NOTES: A. Trace feedback length FBOUT to FBIN = 5 mm, ZO = 50 Ω Phase error measured from CLK to Y
B. CLF = Lumped feedback capacitance at FBIN
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
CDC2509C
3.3-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS620 – DECEMBER 1998
TYPICAL CHARACTERISTICS
PHASE ERROR
vs
CLOCK FREQUENCY
PHASE ERROR
vs
SUPPLY VOLTAGE
0
0
VCC = 3.3 V
C(LY) = 30 pF
C(LF) = 0
TA = 25°C
See Note A
–50
–150
–100
–150
Phase Error – ps
Phase Error – ps
–100
–200
–250
–300
–200
–250
–300
–350
–350
–400
–400
–450
–450
–500
fc = 100 MHz
C(LY) = 30 pF
C(LF) = 0
TA = 25°C
See Note A
–50
20
40
60
80
100
120
140
–500
3.1
160
3.2
fc – Clock Frequency – MHz
Figure 5
CDC2509C
CDC2509A
STATIC PHASE ERROR
vs
CLOCK FREQUENCY
STATIC PHASE ERROR
vs
CLOCK FREQUENCY
3.5
–200
VCC = 3.3 V
C(LY) = C(LF) = 30 pF
TA = 25°C
See Notes B to D
VCC = 3.3 V
C(LY) = C(LF) = 30 pF
See Notes B to D
–300
Static Phase Error – ps
–300
Static Phase Error – ps
3.4
Figure 6
–200
–400
–500
–600
–400
–500
–600
–700
35
45
55
65
75
85
95
105
115
–700
125
35
45
fc – Clock Frequency – MHz
NOTES: A.
B.
C.
D.
55
65
75
85
Figure 8
Trace feedback length FBOUT to FBIN = 5 mm, ZO = 50 Ω
Phase error measured from CLK to FBIN
CLY = Lumped capacitive load at Y
CLF = Lumped feedback capacitance at FBIN
POST OFFICE BOX 655303
95
105 115
fc – Clock Frequency – MHz
Figure 7
8
3.3
VCC – Supply Voltage – V
• DALLAS, TEXAS 75265
125
CDC2509C
3.3-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS620 – DECEMBER 1998
TYPICAL CHARACTERISTICS
CDC2509C
CDC2509A
JITTER
vs
CLOCK FREQUENCY
JITTER
vs
CLOCK FREQUENCY
400
700
VCC = 3.3 V
C(LY) = C(LF) = 30 pF
TA = 25°C
See Notes A and B
350
VCC = 3.3 V
C(LY) = C(LF) = 30 pF
TA = 25°C
See Notes A and B
600
300
Jitter – ps
Jitter – ps
500
250
200
150
0
35
Peak to Peak
300
Peak to Peak
200
100
50
400
Cycle to Cycle
Cycle to Cycle
45
55
65
100
75
85
95
0
35
105 115 125
45
55
fc – Clock Frequency – MHz
65
Figure 9
250
8
6
4
200
AVCC = VCC = 3.465 V
Bias = 0/3 V
C(LY) = 30 pf
C(LF) = 0
TA = 25°C
See Notes A and B
150
100
50
2
0
10
105 115 125
300
AVCC = VCC = 3.465 V
Bias = 0/3 V
C(LY) = 30 pf
C(LF) = 0
TA = 25°C
See Notes A and B
I CC – Supply Current – mA
AI CC – Analog Supply Current – mA
10
95
SUPPLY CURRENT
vs
CLOCK FREQUENCY
16
12
85
Figure 10
ANALOG SUPPLY CURRENT
vs
CLOCK FREQUENCY
14
75
fc – Clock Frequency – MHz
30
50
70
90
110
130
150
0
10
30
fc – Clock Frequency – MHz
50
70
90
110
130
150
fc – Clock Frequency – MHz
Figure 11
Figure 12
NOTES: A. C(LY) = Lumped capacitive load at Y
B. C(LF) = Lumped feedback capacitance at FBIN
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
CDC2509C
3.3-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS620 – DECEMBER 1998
TYPICAL CHARACTERISTICS
TI SILICON-BASED
PLL PULLDOWN IBIS I/V
TI SILICON-BASED
PLL PULLUP IBIS I/V
0
VCC = 3.465 V
High IDS
TA = 0°C
100
I OH – High-Level Output Current – mA
I OL – Low-Level Output Current – mA
120
Imax (Intel)
80
VCC = 3.3 V
Nom IDS
TA = 25°C
60
40
VCC = 3.135 V
Low IDS
TA = 85°C
20
VCC = 3.135 V
Low IDS
TA = 85°C
–20
Imin (Intel)
–40
VCC = 3.3 V
Nom IDS
TA = 25°C
–60
VCC = 3.465 V
High IDS
TA = 0°C
–80
Imin (Intel)
Imax (Intel)
0
0
0.5
1
1.5
2
2.5
3
3.5
–100
0
0.5
VO – Output Voltage – V
Figure 13
10
1
1.5
Figure 14
POST OFFICE BOX 655303
2
2.5
VO – Output Voltage – V
• DALLAS, TEXAS 75265
3
3.5
CDC2509C
3.3-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS620 – DECEMBER 1998
MECHANICAL INFORMATION
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
0,75
0,50
A
Seating Plane
1,20 MAX
0,10
0,05 MIN
PINS **
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064 / E 08/96
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1998, Texas Instruments Incorporated