CS5166H 5-Bit Synchronous CPU Controller with Power Good and Current Limit The CS5166H is a synchronous dual NFET buck controller. It is designed to power the core logic of the latest high performance CPUs. It uses V2 control method to achieve the fastest possible transient response and best overall regulation. It incorporates many additional features required to ensure the proper operation and protection of the CPU and power system. The CS5166H provides the industry’s most highly integrated solution, minimizing external component count, total solution size, and cost. The CS5166H is specifically designed to power Intel’s PentiumII processor and includes the following features: 5–bit DAC with 1.0% tolerance, Power Good output, adjustable hiccup mode overcurrent protection, VCC monitor, Soft Start, adaptive voltage positioning, overvoltage protection, remote sense and current sharing capability. The CS5166H will operate over a 4.15 to 20 V range using either single or dual input voltage and is available in a 16 lead wide body surface mount package. Features • V2 Control Topology • Dual N–Channel Design • 125 ns Controller Transient Response • Excess of 1.0 MHz Operation • 5–Bit DAC with 1.0% Tolerance • Power Good Output With Internal Delay • Adjustable Hiccup Mode Overcurrent Protection • Complete Pentium II System Requires Just 21 Components • 5.0 V & 12 V Operation Using Either Dual or Single Supplies • Adaptive Voltage Positioning • Remote Sense Capability • Current Sharing Capability • VCC Monitor • Overvoltage Protection (OVP) • Programmable Soft Start • 200 ns PWM Blanking • 65 ns FET Nonoverlap Time • 40 ns Gate Rise and Fall Times (3.3 nF Load) Semiconductor Components Industries, LLC, 2001 January, 2001 – Rev. 2 1 http://onsemi.com MARKING DIAGRAM 16 16 1 CS5166H SO–16L DW SUFFIX CASE 751G AWLYYWW 1 A WL, L YY, Y WW, W = Assembly Location = Wafer Lot = Year = Work Week PIN CONNECTIONS 1 16 VFB COMP LGND PWRGD GATE(L) PGND GATE(H) VCC VID0 VID1 VID2 VID3 SS VID4 COFF ISENSE ORDERING INFORMATION Device Package Shipping CS5166HGDW16 SO–16L 46 Units/Rail CS5166HGDWR16 SO–16L 1000 Tape & Reel Publication Order Number: CS5166H/D CS5166H 5.0 V 1200 µF/10 V × 3 12 V 1.0 µF 330 pF VCC COFF SS 0.1 µF 1.2 µH 3.0 mΩ GATE(H) 510 CS5166H COMP 0.1 µF VID0 VID1 1200 µF/10 V × 5 VCC ISENSE PWRGD 0.1 µF GATE(L) VID2 PGND VID4 LGND VID3 VID3 Pentium II System VID2 VID1 VID4 3.3 k PWRGD VFB VID0 1000 pF Figure 1. Application Diagram, 5.0 V to 2.8 V @ 14.2 A for 300 MHz Pentium II ABSOLUTE MAXIMUM RATINGS* Rating Operating Junction Temperature, TJ Lead Temperature Soldering: Reflow: (SMD styles only) (Note 1.) Storage Temperature Range, TS 1. 60 second maximum above 183°C. *The maximum package power dissipation must be observed. http://onsemi.com 2 Value Unit 0 to 150 °C 230 peak °C –65 to +150 °C CS5166H ABSOLUTE MAXIMUM RATINGS Pin Name Pin Symbol VMAX VMIN ISOURCE ISINK IC Power Input VCC 20 V –0.3 V N/A 1.5 A peak, 200 mA DC Soft Start Capacitor SS 6.0 V –0.3 V 200 µA 10 µA Compensation Capacitor COMP 6.0 V –0.3 V 10 mA 1.0 mA Voltage Feedback and Current Sense Comparator Input VFB 6.0 V –0.3 V 1.0 mA 1.0 mA Off–Time Capacitor COFF 6.0 V –0.3 V 1.0 mA 50 mA Voltage ID DAC Inputs VID0–VID4 6.0 V –0.3 V 1.0 mA 10 µA High–Side FET Driver GATE(H) 20 V –0.3 V 1.5 A peak, 200 mA DC 1.5 A peak, 200 mA DC Low–Side FET Driver GATE(L) 20 V –0.3 V 1.5 A peak, 200 mA DC 1.5 A peak, 200 mA DC Current Sense Comparator Input ISENSE 6.0 V –0.3 V 1.0 mA 1.0 mA Power Good Output PWRGD 6.0 V –0.3 V 10 µA 30 mA Power Ground PGND 0V 0V 1.5 A peak, 200 mA DC N/A Logic Ground LGND 0V 0V 100 mA N/A ELECTRICAL CHARACTERISTICS (0°C < TA < 70°C; 0°C < TJ < 125°C; 8.0 V < VCC < 20 V; 2.0 DAC Code: (VID4 = VID3 = VID2 = VID1 = 0, VID0 = 1), CGATE(H) = CGATE(L) = 3.3 nF; COFF = 330 pF; CSS = 0.1 µF, unless otherwise specified.) Test Conditions Characteristic Min Typ Max Unit – 12 20 mA VCC Supply Current Operating 1.0 V < VFB < VDAC (max on–time), No Loads on GATE(H) and GATE(L) VCC Monitor Start Threshold GATE(H) switching 3.75 3.95 4.15 V Stop Threshold GATE(H) not switching 3.65 3.87 4.05 V Hysteresis Start–Stop – 80 – mV VFB Bias Current VFB = 0 V – 0.1 1.0 µA COMP Source Current COMP = 1.2 V to 3.6 V; VFB = 1.9 V 15 30 60 µA COMP CLAMP Voltage VFB = 1.9 V, Adjust COMP voltage for Comp current = 60 µA 0.85 1.0 1.15 V COMP Clamp Current COMP = 0 V 0.4 1.0 1.6 mA COMP Sink Current VCOMP = 1.2 V; VFB = 2.2 V; VSS > 2.5 V 180 400 800 µA Open Loop Gain Note 2. 50 60 – dB Unity Gain Bandwidth Note 2. 0.5 2.0 – MHz PSRR @ 1.0 kHz Note 2. 60 85 – dB Current Limit Voltage VFB = 0 V to 3.5 V, 8.0 V < VCC < 12 V + 10% 55 76 130 mV ISENSE Bias Current ISENSE = 2.8 V 13 30 50 µA Error Amplifier Overcurrent Detection 2. Guaranteed by design, not 100% tested in production. http://onsemi.com 3 CS5166H ELECTRICAL CHARACTERISTICS (continued) (0°C < TA < 70°C; 0°C < TJ < 125°C; 8.0 V < VCC < 20 V; 2.0 DAC Code: (VID4 = VID3 = VID2 = VID1 = 0, VID0 = 1), CGATE(H) = CGATE(L) = 3.3 nF; COFF = 330 pF; CSS = 0.1 µF, unless otherwise specified.) Characteristic Test Conditions Min Typ Max Unit V GATE(H) and GATE(L) High Voltage at 100 mA Measure VCC – GATE – 1.2 2.0 Low Voltage at 100 mA Measure GATE – 1.0 1.5 V Rise Time 1.6 V < GATE < (VCC – 2.5 V), 8.0 V < VCC < 14 V – 40 80 ns Fall Time (VCC – 2.5 V) > GATE > 1.6 V, 8.0 V < VCC < 14 V – 40 80 ns GATE(H) to GATE(L) Delay GATE(H) < 2.0 V; GATE(L) > 2.0 V, 8.0 V < VCC < 14 V 30 65 100 ns GATE(L) to GATE(H) Delay GATE(L) < 2.0 V; GATE(H) > 2.0 V, 8.0 V < VCC < 14 V 30 65 100 ns GATE pull–down Resistor to PGND, Note 3. 20 50 115 kΩ SS Charge Time VFB = 3.0 V, VISENSE = 2.8 V 1.6 3.3 5.0 ms SS Pulse Period VFB = 3.0 V, VISENSE = 2.8 V 25 100 200 ms SS Duty Cycle (Charge Time/Period) × 100 1.0 3.3 6.0 % SS COMP Clamp Voltage VFB = 2.7 V; VSS = 0 V 0.50 0.95 1.10 V VFB Low Comparator Increase VFB till normal off–time 0.9 1.0 1.1 V Fault Protection PWM Comparator Transient Response VFB = 1.2 to 5.0 V. 500 ns after GATE(H) (after Blanking time) to GATE(H) = (VCC –1.0 V) to 1.0 V, 8.0 V < VCC < 14 V – 115 175 ns Minimum Pulse Width (Blanking Time) Drive VFB 1.2 V to 5.0 V upon GATE(H) rising edge (> VCC – 1.0 V), measure GATE(H) pulse width, 8.0 V < VCC < 14 V 100 200 300 ns Normal Off–Time VFB = 2.7 V 1.0 1.6 2.3 µs Extended Off–Time VSS = VFB = 0 V 5.0 8.0 12.0 µs Time–Out Time VFB = 2.7 V, Measure GATE(H) Pulse Width 10 30 50 µs Fault Duty Cycle VFB = 0V 30 50 70 % Low to High Delay VFB = (0.8 × VDAC) to VDAC 30 65 110 µs High to Low Delay VFB = VDAC to (0.8 × VDAC) 30 75 120 µs Output Low Voltage VFB = 2.4 V, IPWRGD = 500 µA – 0.2 0.3 V Sink Current Limit VFB = 2.4 V, PWRGD = 1.0 V 0.5 4.0 15.0 mA COFF Time–Out Timer Power Good Output 3. Guaranteed by design, not 100% tested in production. http://onsemi.com 4 CS5166H ELECTRICAL CHARACTERISTICS (continued) (0°C < TA < 70°C; 0°C < TJ < 125°C; 8.0 V < VCC < 20 V; 2.0 DAC Code: (VID4 = VID3 = VID2 = VID1 = 0, VID0 = 1), CGATE(H) = CGATE(L) = 3.3 nF; COFF = 330 pF; CSS = 0.1 µF, unless otherwise specified.) Characteristic Test Conditions Min Typ Max Unit –1.0 – +1.0 % Voltage Identification DAC Accuracy (all codes except 11111) Measure VFB = COMP (COFF = GND) 25°C ≤ TJ ≤ 125°C; VCC = 12 V VID4 VID3 VID2 VID1 VID0 1 0 0 0 0 – 3.489 3.525 3.560 V 1 0 0 0 1 – 3.390 3.425 3.459 V 1 0 0 1 0 – 3.291 3.325 3.358 V 1 0 0 1 1 – 3.192 3.225 3.257 V 1 0 1 0 0 – 3.093 3.125 3.156 V 1 0 1 0 1 – 2.994 3.025 3.055 V 1 0 1 1 0 – 2.895 2.925 2.954 V 1 0 1 1 1 – 2.796 2.825 2.853 V 1 1 0 0 0 – 2.697 2.725 2.752 V 1 1 0 0 1 – 2.598 2.625 2.651 V 1 1 0 1 0 – 2.499 2.525 2.550 V 1 1 0 1 1 – 2.400 2.425 2.449 V 1 1 1 0 0 – 2.301 2.325 2.348 V 1 1 1 0 1 – 2.202 2.225 2.247 V 1 1 1 1 0 – 2.103 2.125 2.146 V 0 0 0 0 0 – 2.054 2.075 2.095 V 0 0 0 0 1 – 2.004 2.025 2.045 V 0 0 0 1 0 – 1.955 1.975 1.994 V 0 0 0 1 1 – 1.905 1.925 1.944 V 0 0 1 0 0 – 1.856 1.875 1.893 V 0 0 1 0 1 – 1.806 1.825 1.843 V 0 0 1 1 0 – 1.757 1.775 1.792 V 0 0 1 1 1 – 1.707 1.725 1.742 V 0 1 0 0 0 – 1.658 1.675 1.691 V 0 1 0 0 1 – 1.608 1.625 1.641 V 0 1 0 1 0 – 1.559 1.575 1.590 V 0 1 0 1 1 – 1.509 1.525 1.540 V 0 1 1 0 0 – 1.460 1.475 1.489 V 0 1 1 0 1 – 1.410 1.425 1.439 V 0 1 1 1 0 – 1.361 1.375 1.388 V 0 1 1 1 1 – 1.311 1.325 1.338 V 1 1 1 1 1 – 1.219 1.247 1.269 V Input Threshold VID4, VID3, VID2, VID1, VID0 1.000 1.250 2.400 V Input Pull–up Resistance VID4, VID3, VID2, VID1, VID0 25 50 100 kΩ 4.85 5.00 5.15 V Input Pull–up Voltage http://onsemi.com 5 CS5166H ELECTRICAL CHARACTERISTICS (continued) (0°C < TA < 70°C; 0°C < TJ < 125°C; 8.0 V < VCC < 20 V; 2.0 DAC Code: (VID4 = VID3 = VID2 = VID1 = 0, VID0 = 1); CGATE(H) = CGATE(L) = 3.3 nF; COFF = 330 pF; CSS = 0.1 µF, unless otherwise specified.) Lower Threshold Threshold Accuracy Acc racy Min Typ –12 –8.5 Upper Threshold Max Min Typ Max Unit –5.0 5.0 8.5 12 % DAC CODE % of Nominal DAC Output VID4 VID3 VID2 VID1 VID0 1 0 0 0 0 3.102 3.225 3.348 3.701 3.824 3.948 V 1 0 0 0 1 3.014 3.133 3.253 3.596 3.716 3.836 V 1 0 0 1 0 2.926 3.042 3.158 3.491 3.607 3.724 V 1 0 0 1 1 2.838 2.950 3.063 3.386 3.499 3.612 V 1 0 1 0 0 2.750 2.859 2.968 3.281 3.390 3.500 V 1 0 1 0 1 2.662 2.767 2.873 3.176 3.282 3.388 V 1 0 1 1 0 2.574 2.676 2.778 3.071 3.173 3.276 V 1 0 1 1 1 2.486 2.584 2.683 2.966 3.065 3.164 V 1 1 0 0 0 2.398 2.493 2.588 2.861 2.956 3.052 V 1 1 0 0 1 2.310 2.401 2.493 2.756 2.848 2.940 V 1 1 0 1 0 2.222 2.310 2.398 2.651 2.739 2.828 V 1 1 0 1 1 2.134 2.218 2.303 2.546 2.631 2.716 V 1 1 1 0 0 2.046 2.127 2.208 2.441 2.522 2.604 V 1 1 1 0 1 1.958 2.035 2.113 2.336 2.414 2.492 V 1 1 1 1 0 1.870 1.944 2.018 2.231 2.305 2.380 V 0 0 0 0 0 1.826 1.898 1.971 2.178 2.251 2.324 V 0 0 0 0 1 1.782 1.8520 1.923 2.126 2.197 2.268 V 0 0 0 1 0 1.738 1.807 1.876 2.073 2.142 2.212 V 0 0 0 1 1 1.694 1.761 1.828 2.021 2.088 2.156 V 0 0 1 0 0 1.650 1.715 1.781 1.968 2.034 2.100 V 0 0 1 0 1 1.606 1.669 1.733 1.916 1.980 2.044 V 0 0 1 1 0 1.562 1.624 1.686 1.863 1.925 1.988 V 0 0 1 1 1 1.518 1.578 1.638 1.811 1.871 1.932 V 0 1 0 0 0 1.474 1.532 1.591 1.758 1.817 1.876 V 0 1 0 0 1 1.430 1.486 1.543 1.706 1.763 1.820 V 0 1 0 1 0 1.386 1.441 1.496 1.653 1.708 1.764 V 0 1 0 1 1 1.342 1.395 1.448 1.601 1.654 1.708 V 0 1 1 0 0 1.298 1.349 1.401 1.548 1.600 1.652 V 0 1 1 0 1 1.254 1.303 1.353 1.496 1.546 1.596 V 0 1 1 1 0 1.210 1.258 1.306 1.443 1.491 1.540 V 0 1 1 1 1 1.166 1.212 1.258 1.391 1.437 1.484 V 1 1 1 1 1 1.094 1.138 1.181 1.306 1.349 1.393 V http://onsemi.com 6 CS5166H PACKAGE PIN DESCRIPTION PACKAGE PIN # SO–16L PIN SYMBOL FUNCTION 1, 2, 3, 4, 6 VID0–VID4 Voltage ID DAC input pins. These pins are internally pulled up to 5.0 V if left open. VID4 selects the DAC range. When VID4 is high (logic one), the Error Amp reference range is 2.125 V to 3.525 V with 100 mV increments. When VID4 is low (logic zero), the Error Amp reference voltage is 1.325 V to 2.075 V with 50 mV increments. 5 SS Soft Start Pin. A capacitor from this pin to LGND sets the Soft Start and fault timing. 7 COFF Off–Time Capacitor Pin. A capacitor from this pin to LGND sets both the normal and extended off time. 8 ISENSE 9 VCC 10 GATE(H) 11 PGND 12 GATE(L) Low Side Synchronous FET driver pin. 13 PWRGD Power Good Output. Open collector output drives low when VFB is out of regulation. 14 LGND Reference ground. All control circuits are referenced to this pin. 15 COMP Error Amp output. PWM Comparator reference input. A capacitor to LGND provides Error Amp compensation. 16 VFB Error Amp, PWM Comparator feedback input, Current Sense Comparator Non–Inverting input, and PWRGD Comparator input. Current Sense Comparator Inverting Input. Input Power Supply Pin. High Side Switch FET driver pin. High current ground for the GATE(H) and GATE(L) pins. http://onsemi.com 7 CS5166H – VCC Monitor VCC + 3.95 V 3.87V VGATE(H) 5.0 V – SS Low Comparator R Q S Q + 60 µA 0.7 V SS + 2.0 µA FAULT FAULT PGND FAULT Latch SS High Comparator VCC – VCC1 VGATE(L) 2.5 V COMP VID0 Error Amplifier 5 BIT DAC VID2 PGND PWM Comparator + VID1 – VID3 VID4 – PWM COMP + Blanking VCC –8.5% +8.5% + – – + 76 mV 30 µA Extended Off–Time Timeout + 65 µs Delay R Q S Q PWM Latch Normal Off–Time – PWRGD GATE(H) = ON Maximum On–Time Timeout Off–Time Timeout GATE(H) = OFF COFF One Shot R S ISENSE Comparator VFB Time–Out Timer – + ISENSE 1.0 V VFB Low Comparator LGND Figure 2. Block Diagram http://onsemi.com 8 Edge Triggered COFF Q CS5166H 200 200 180 180 160 160 140 140 Risetime (ns) Risetime (ns) TYPICAL PERFORMANCE CHARACTERISTICS 120 100 80 60 0 0 2000 4000 80 VCC = 12 V 40 TA = 25°C 20 100 60 VCC = 12 V 40 120 TA = 25°C 20 0 6000 8000 10000 12000 14000 16000 0 2000 4000 Load Capacitance (pF) Load Capacitance (pF) Figure 3. GATE(L) Risetime vs. Load Capacitance Figure 4. GATE(H) Risetime vs. Load Capacitance 0.04 DAC Output Voltage Deviation (%) 200 180 160 Falltime (ns) 140 120 100 80 60 40 VCC = 12 V 20 TA = 25°C 0 0 2000 4000 0.02 0 –0.02 –0.04 –0.06 –0.08 –0.1 6000 8000 10000 12000 14000 16000 0 20 40 Load Capacitance (pF) 60 80 100 120 Junction Temperature (°C) Figure 5. GATE(H) & GATE(L) Falltime vs. Load Capacitance Figure 6. DAC Output Voltage vs. Temperature, DAC Code = 10111, VCC = 12 V 0.04 0.05 0.02 0 0 Output Error (%) Output Error (%) 6000 8000 10000 12000 14000 16000 –0.02 –0.04 –0.05 –0.10 –0.15 DAC Output Voltage Setting (V) DAC Output Voltage Setting (V) Figure 7. Percent Output Error vs. DAC Voltage Setting, VCC = 12 V, TA = 25°C, VID4 = 0 Figure 8. Percent Output Error vs. DAC Output Voltage Setting VCC = 12 V, TA = 25°C, VID4 = 1 http://onsemi.com 9 3.525 3.425 3.325 3.225 3.125 3.025 2.925 2.825 2.725 2.625 2.525 2.425 2.325 2.125 2.075 2.025 1.975 1.925 1.875 1.825 1.775 1.675 1.725 1.625 1.575 1.525 1.475 –0.25 1.425 –0.10 1.325 –0.20 1.375 –0.08 2.225 –0.06 CS5166H APPLICATIONS INFORMATION THEORY OF OPERATION since the error amplifier bandwidth can be rolled off at a low frequency. Enhanced noise immunity improves remote sensing of the output voltage, since the noise associated with long feedback traces can be effectively filtered. The Bode plot in Figure 10 shows the gain and phase margin of the CS5166H single pole feedback loop and demonstrates the overall stability of the CS5166H–based regulator. V2 Control Method The V2 method of control uses a ramp signal that is generated by the ESR of the output capacitors. This ramp is proportional to the AC current through the main inductor and is offset by the value of the DC output voltage. This control scheme inherently compensates for variation in either line or load conditions, since the ramp signal is generated from the output voltage itself. This control scheme differs from traditional techniques such as voltage mode, which generates an artificial ramp, and current mode, which generates a ramp from inductor current. PWM Comparator GATE(H) C GATE(L) – + Ramp Signal VFB Error Amplifier COMP Error Signal Figure 10. Feedback Loop Bode Plot – E + Line and load regulation are drastically improved because there are two independent voltage loops. A voltage mode controller relies on a change in the error signal to compensate for a deviation in either line or load voltage. This change in the error signal causes the output voltage to change corresponding to the gain of the error amplifier, which is normally specified as line and load regulation. A current mode controller maintains fixed error signal under deviation in the line voltage, since the slope of the ramp signal changes, but still relies on a change in the error signal for a deviation in load. The V2 method of control maintains a fixed error signal for both line and load variation, since the ramp signal is affected by both line and load. Reference Voltage Figure 9. V2 Control Diagram V2 The control method is illustrated in Figure 9. The output voltage is used to generate both the error signal and the ramp signal. Since the ramp signal is simply the output voltage, it is affected by any change in the output regardless of the origin of that change. The ramp signal also contains the DC portion of the output voltage, which allows the control circuit to drive the main switch to 0% or 100% duty cycle as required. A change in line voltage changes the current ramp in the inductor, affecting the ramp signal, which causes the V2 control scheme to compensate the duty cycle. Since the change in inductor current modifies the ramp signal, as in current mode control, the V2 control scheme has the same advantages in line transient response. A change in load current will have an affect on the output voltage, altering the ramp signal. A load step immediately changes the state of the comparator output, which controls the main switch. Load transient response is determined only by the comparator response time and the transition speed of the main switch. The reaction time to an output load step has no relation to the crossover frequency of the error signal loop, as in traditional control methods. The error signal loop can have a low crossover frequency, since transient response is handled by the ramp signal loop. The main purpose of this ‘slow’ feedback loop is to provide DC accuracy. Noise immunity is significantly improved, Constant Off Time To maximize transient response, the CS5166H uses a constant off time method to control the rate of output pulses. During normal operation, the off time of the high side switch is terminated after a fixed period, set by the COFF capacitor. To maintain regulation, the V2 control loop varies switch on time. The PWM comparator monitors the output voltage ramp, and terminates the switch on time. Constant off time provides a number of advantages. Switch duty cycle can be adjusted from 0 to 100% on a pulse by pulse basis when responding to transient conditions. Both 0% and 100% duty cycle operation can be maintained for extended periods of time in response to load or line transients. PWM slope compensation to avoid sub–harmonic oscillations at high duty cycles is avoided. http://onsemi.com 10 CS5166H Switch on time is limited by an internal 30 µs (typical) timer, minimizing stress to the power components. Programmable Output The CS5166H is designed to provide two methods for programming the output voltage of the power supply. A five bit on board digital to analog converter (DAC) is used to program the output voltage within two different ranges. The first range is 2.125 V to 3.525 V in 100 mV steps, the second is 1.325 V to 2.075 V in 50 mV steps, depending on the digital input code. If all five bits are left open, the CS5166H enters adjust mode. In adjust mode, the designer can choose any output voltage by using resistor divider feedback to the VFB pin, as in traditional controllers. The CS5166H is specifically designed to meet or exceed Intel’s Pentium II specifications. M 250 µs Trace 1– Regulator Output Voltage (1.0 V/div.) Trace 2– Inductor Switching Node (2.0 V/div.) Trace 3– 12 V Input (VCC) (5.0 V/div.) Trace 4– 5.0 V Input (1.0 V/div.) Figure 11. Demonstration Board Startup in Response to Increasing 12 V and 5.0 V Input Voltages. Extended Off Time is Followed by Normal Off Time Operation when Output Voltage Achieves Regulation to the Error Amplifier Output. Start Up Until the voltage on the VCC supply pin exceeds the 3.95 V monitor threshold, the Soft Start and GATE pins are held low. The FAULT latch is reset (no Fault condition). The output of the error amplifier (COMP) is pulled up to 1.0 V by the comparator clamp. When the VCC pin exceeds the monitor threshold, the GATE(H) output is activated, and the Soft Start capacitor begins charging. The GATE(H) output will remain on, enabling the NFET switch, until terminated by either the PWM comparator, or the maximum on time timer. If the maximum on time is exceeded before the regulator output voltage achieves the 1.0 V level, the pulse is terminated. The GATE(H) pin drives low, and the GATE(L) pin drives high for the duration of the extended off time. This time is set by the time out timer and is approximately equal to the maximum on time, resulting in a 50% duty cycle. The GATE(L) pin will then drive low, the GATE(H) pin will drive high, and the cycle repeats. When regulator output voltage achieves the 1.0 V level present at the COMP pin, regulation has been achieved and normal off time will ensue. The PWM comparator terminates the switch on time, with off time set by the COFF capacitor. The V2 control loop will adjust switch duty cycle as required to ensure the regulator output voltage tracks the output of the error amplifier. The Soft Start and COMP capacitors will charge to their final levels, providing a controlled turn on of the regulator output. Regulator turn on time is determined by the COMP capacitor charging to its final value. Its voltage is limited by the Soft Start COMP clamp and the voltage on the Soft Start pin. Trace 1– Regulator Output Voltage (1.0 V/div.). Trace 3– COMP PIn (error amplifier output) (1.0 V/div.). Trace 4– Soft Start Pin (2.0 V/div.). Figure 12. Demonstration Board Startup Waveforms http://onsemi.com 11 CS5166H M 10.0 µs Trace 1– GATE(H) (10 V/div.) Trace 2– Inductor Switching Node (5.0 V/div.) Trace 3– Output Inductor Ripple Current (2.0 A/div.) Trace 4– VOUT ripple (20 mV/div.) Trace 1– Regulator Output Voltage (5.0 V/div.) Trace 2– Inductor Switching Node (5.0 V/div.) Figure 13. Demonstration Board Enable Startup Waveforms Figure 15. Normal Operation Showing Output Inductor Ripple Current and Output Voltage Ripple, ILOAD = 14 A, VOUT = +2.825 V (DAC = 10111) Normal Operation During normal operation, switch off time is constant and set by the COFF capacitor. Switch on time is adjusted by the V2 control loop to maintain regulation. This results in changes in regulator switching frequency, duty cycle, and output ripple in response to changes in load and line. Output voltage ripple will be determined by inductor ripple current working and the ESR of the output capacitors (see Figures 14 and 15). Transient Response The CS5166H V2 control loop’s 150 ns reaction time provides unprecedented transient response to changes in input voltage or output current. Pulse by pulse adjustment of duty cycle is provided to quickly ramp the inductor current to the required level. Since the inductor current cannot be changed instantaneously, regulation is maintained by the output capacitor(s) during the time required to slew the inductor current. Overall load transient response is further improved through a feature called “Adaptive Voltage Positioning”. This technique pre–positions the output capacitors voltage to reduce total output voltage excursions during changes in load. Holding tolerance to 1.0% allows the error amplifiers reference voltage to be targeted +25 mV high without compromising DC accuracy. A “Droop Resistor”, implemented through a PC board trace, connects the Error Amps feedback pin (VFB) to the output capacitors and load and carries the output current. With no load, there is no DC drop across this resistor, producing an output voltage tracking the Error amps, including the +25 mV offset. When the full load current is delivered, an 50 mV drop is developed across this resistor. This results in output voltage being offset –25 mV low. The result of Adaptive Voltage Positioning is that additional margin is provided for a load transient before Trace 1– GATE(H) (10 V/div.) Trace 2– Inductor Switching Node (5.0 V/div.) Trace 3– Output Inductor Ripple Current (2.0 A/div.) Trace 4– VOUT ripple (20 mV/div.) Figure 14. Normal Operation Showing Output Inductor Ripple Current and Output Voltage Ripple, 0.5 A Load, VOUT = +2.825 V (DAC = 10111) http://onsemi.com 12 CS5166H reaching the output voltage specification limits. When load current suddenly increases from its minimum level, the output capacitor is pre–positioned +25 mV. Conversely, when load current suddenly decreases from its maximum level, the output capacitor is pre–positioned –25 mV (see Figures 16, 17, and 18). For best Transient Response, a combination of a number of high frequency and bulk output capacitors are usually used. If the Maximum On–Time is exceeded while responding to a sudden increase in Load current, a normal off–time occurs to prevent saturation of the output inductor. Trace 1– GATE(H) (10 V/div.) Trace 2– Inductor Switching Node (5.0 V/div.) Trace 3– Load Current (5.0 A/div) Trace 4– VOUT (100 mV/div.) Figure 18. Output Voltage Transient Response to a 14 A Load Turn–Off, VOUT = +2.825 V (DAC = 10111) Power Supply Sequencing The CS5166H offers inherent protection from undefined start up conditions, regardless of the 12 V and 5.0 V supply power up sequencing. The turn on slew rates of the 12 V and 5.0 V power supplies can be varied over wide ranges without affecting the output voltage or causing detrimental effects to the buck regulator. Trace 3– Load Current (5.0 A/10 mV/div.) Trace 4– VOUT (100 mV/div.) PROTECTION AND MONITORING FEATURES Figure 16. Output Voltage Transient Response to a 14 A Load Pulse, VOUT = +2.825 V (DAC = 10111) Overcurrent Protection A loss–less hiccup mode current limit protection feature is provided, requiring only the Soft Start capacitor to implement. The CS5166H provides overcurrent protection by sensing the current through a “Droop” resistor, using an internal current sense comparator. The comparator compares this voltage drop to an internal reference voltage of 76 mV (typical). If the voltage drop across the “Droop” resistor exceeds this threshold, the current sense comparator allows the fault latch to be set. This causes the regulator to stop switching. During this overcurrent condition, the CS5166H stays off for the time it takes the Soft Start capacitor to slowly discharge by a 2.0 µA current source until it reaches its lower 0.7 V threshold. At that time the regulator attempts to restart normally by delivering short gate pulses to both FET’s. The CS5166H will operate initially in its extended off time mode with a 50% duty cycle, while the Soft Start capacitor is charged with a 60 mA charge current. The gates will switch on while the Soft Start capacitor is charged to its upper 2.7 V Trace 1– GATE(H) (10 V/div.) Trace 2– Inductor Switching Node (5.0 V/div.) Trace 3– Load Current (5.0 A/div) Trace 4– VOUT (100 mV/div.) Figure 17. Output Voltage Transient Response to a 14 A Load Step, VOUT = +2.825 V (DAC = 10111) http://onsemi.com 13 CS5166H MOSFET to shut off, disconnecting the regulator from it’s input voltage. The bottom MOSFET is then activated, resulting in a “crowbar” action to clamp the output voltage and prevent damage to the load (see Figures 21 and 22 ). The regulator will remain in this state until the overvoltage condition ceases or the input voltage is pulled low. The bottom FET and board trace must be properly designed to implement the OVP function. If a dedicated OVP output is required, it can be implemented using the circuit in Figure 23. In this figure the OVP signal will go high (overvoltage condition), if the output voltage (VCORE) exceeds 20% of the voltage set by the particular DAC code and provided that PWRGD is low. It is also required that the overvoltage condition be present for at least the PWRGD delay time for the OVP signal to be activated. The resistor values shown in Figure 23 are for VDAC = +2.8 V (DAC = 10111). The VOVP (overvoltage trip–point) can be set using the following equation: threshold. During an overload condition the Soft Start charge/discharge current ratio sets the duty cycle for the pulses (2.0 µA/60 µA = 3.3%), while actual duty cycle is half that due to the extended off time mode (1.65%) when VFB is less than 1.0 V. The Soft Start hiccup pulses last for a 3.0 ms period at the end of which the duty cycle repeats if a fault is detected, otherwise normal operation resumes. The protection scheme minimizes thermal stress to the regulator components, input power supply, and PC board traces, as the overcurrent condition persists. Upon removal of the overload, the fault latch is cleared, allowing normal operation to resume. The current limit trip point can be adjusted through an external resistor, providing the user with the current limit set–point flexibility. VOVP VBEQ3 1 R2 R1 M 25.0 ms Trace 4– 5.0 V Supply Voltage (2.0 V/div.) Trace 3– Soft Start Timing Capacitor (1.0 V/div.) Trace 2– Inductor Switching Node (2.0 V/div.) Figure 19. Demonstration Board Hiccup Mode Short Circuit Protection. Gate Pulses are Delivered While the Soft Start Capacitor Charges, and Cease During Discharge M 10.0 µs Trace 4– 5.0 V from PC Power Supply (5.0 V/div.) Trace 1– Regulator Output Voltage (1.0 V/div.) Trace 2– Inductor Switching Node 5.0 V/div.) Figure 21. OVP Response to an Input–to–Output Short Circuit by Immediately Providing 0% Duty Cycle, Crow–Barring the Input Voltage to Ground M 50.0 µs Trace 4– 5.0 V from PC Power Supply (2.0 V/div.) Trace 2– Inductor Switching Node (2.0 V/div.) Figure 20. Demonstration Board Startup with Regulator Output Shorted To Ground Overvoltage Protection Overvoltage protection (OVP) is provided as result of the normal operation of the V2 control topology and requires no additional external components. The control loop responds to an overvoltage condition within 100 ns, causing the top http://onsemi.com 14 CS5166H M 5.00 ms Trace 4– 5.0 V from PC Power Supply (2.0 V/div.) Trace 2– PWRGD (2.0 V/div.) Trace 1– Regulator Output Voltage (1.0 V/div.) Trace 4– VOUT (1.0 V/div.) Figure 22. OVP Response to an Input–to–Output Short Circuit by Pulling the Input Voltage to Ground Figure 24. PWRGD Signal Becomes Logic High as VOUT Enters –8.5% of Lower PWRGD Threshold, VOUT = +2.825 V (DAC = 10111) VCORE 15 k R1 Q3 2N3906 +5.0 V 56 k R2 5.0 k OVP 20 k +5.0 V CS5166H 10 k PWRGD 10 k Q2 2N3904 10 K Q1 2N3906 Figure 23. Circuit To Implement A Dedicated OVP Output Using The CS5166H Trace 2– PWRGD (2.0 V/div.) Trace 4– VFB (1.0 V/div.) Figure 25. Power Good Response to an Out of Regulation Condition Power Good Circuit The Power Good pin (pin 13) is an open–collector signal consistent with TTL DC specifications. It is externally pulled–up, and is pulled low (below 0.3 V) when the regulator output voltage typically exceeds ± 8.5% of the nominal output voltage. Maximum output voltage deviation before Power Good is pulled low is ± 12%. Figure 25 shows the relationship between the regulated output voltage VFB and the Power Good signal. To prevent Power Good from interrupting the CPU unnecessarily, the CS5166H has a built–in delay to prevent noise at the VFB pin from toggling Power Good. The internal time delay is designed to take about 75 µs for Power Good to go low and 65 µs for it to recover. This allows the Power Good signal to be completely insensitive to out of regulation conditions that are present for a duration less than the built in delay (see Figure 26). It is therefore required that the output voltage attains an out of regulation or in regulation level for at least the built–in delay time duration before the Power Good signal can change state. http://onsemi.com 15 CS5166H FET’s may be paralleled to reduce losses and improve efficiency and thermal management. Voltage applied to the FET gates depends on the application circuit used. Both upper and lower gate driver outputs are specified to drive to within 1.5 V of ground when in the low state and to within 2.0 V of their respective bias supplies when in the high state. In practice, the FET gates will be driven rail to rail due to overshoot caused by the capacitive load they present to the controller IC. For the typical application where VCC = 12 V and 5.0 V is used as the source for the regulator output current, the following gate drive is provided: VGS(TOP) 12 V 5.0 V 7.0 V VGS(BOTTOM) 12 V Trace 2– PWRGD (2.0 V/div.) Trace 4– VFB (1.0 V/div.) Figure 26. Power Good is Insensitive to Out of Regulation Conditions that are Present for a Duration Less Than the Built In Delay (see Figure 28) External Output Enable Circuit On/off control of the regulator can be implemented through the addition of two additional discrete components (see Figure ). This circuit operates by pulling the Soft Start pin high, and the ISENSE pin low, emulating a current limit condition. 5.0 V MMUN2111T1 (SOT–23) Trace 3– GATE(H) (10 V/div.) Trace 1– GATE(H) – 5.0 VIN 5 8 Trace 4– GATE(L) (10 V/div.) SS Trace 2– Inductor Switching Node (5.0 V/div.) Figure 28. Gate Drive Waveforms Depicting Rail to Rail Swing CS5166H ISENSE IN4148 Shutdown Input Figure 27. Implementing Shutdown with the CS5166H Selecting External Components The CS5166H buck regulator can be used with a wide range of external power components to optimize the cost and performance of a particular design. The following information can be used as general guidelines to assist in their selection. NFET Power Transistors Both logic level and standard FETs can be used. The reference designs derive gate drive from the 12 V supply which is generally available in most computer systems and utilize logic level FETs. A charge pump may be easily implemented to permit use of standard FET’s or support 5.0 V or 12 V only systems (maximum of 20 V). Multiple Trace 1 = GATE(H) (5.0 V/div.) Trace 2 = GATE(L) (5.0 V/div.) Figure 29. Normal Operation Showing the Guaranteed Non–Overlap Time Between the High and Low–Side MOSFET Gate Drives, ILOAD = 14 A http://onsemi.com 16 CS5166H Power 1.6 V 14.2 A 100 ns 200 kHz 0.45 W The CS5166H provides adaptive control of the external NFET conduction times by guaranteeing a typical 65 ns non–overlap (as seen in Figure 29) between the upper and lower MOSFET gate drive pulses. This feature eliminates the potentially catastrophic effect of “shoot–through current”, a condition during which both FETs conduct causing them to overheat, self–destruct, and possibly inflict irreversible damage to the processor. The most important aspect of FET performance is RDSON, which effects regulator efficiency and FET thermal management requirements. The power dissipated by the MOSFETs may be estimated as follows: Switching MOSFET: This is only 1.1% of the 40 W being delivered to the load. “Droop” Resistor for Adaptive Voltage Positioning Adaptive voltage positioning is used to help keep the output voltage within specification during load transients. To implement adaptive voltage positioning a “Droop Resistor” must be connected between the output inductor and output capacitors and load. This resistor carries the full load current and should be chosen so that both DC and AC tolerance limits are met. An embedded PC trace resistor has the distinct advantage of near zero cost implementation. However, this droop resistor can vary due to three reasons: 1) the sheet resistivity variation causes the thickness of the PCB layer to vary. 2) the mismatch of L/W, and 3) temperature variation. 1. Sheet Resistivity for one ounce copper, the thickness variation typically 1.15 mil to 1.35 mil. Therefore the error due to sheet resistivity is: Power ILOAD2 RDSON duty cycle Synchronous MOSFET: Power ILOAD2 RDSON (1 duty cycle) 1.35 1.15 16% 1.25 Duty Cycle = VOUT (ILOAD RDSON OF SYNCH FET) VIN(ILOAD RDSON OF SYNCH FET) (ILOAD RDSON OF SWITCH FET) 2. Mismatch due to L/W. The variation in L/W is governed by variations due to the PCB manufacturing process that affect the geometry and the power dissipation capability of the droop resistor. The error due to L/W mismatch is typically 1.0%. 3. Thermal Considerations. Due to I2 × R power losses the surface temperature of the droop resistor will increase causing the resistance to increase. Also, the ambient temperature variation will contribute to the increase of the resistance, according to the formula: Off Time Capacitor (COFF) The COFF timing capacitor sets the regulator off time: TOFF COFF 4848.5 The preceding equations for duty cycle can also be used to calculate the regulator switching frequency and select the COFF timing capacitor: R R20[1 20(T 20)] Perioid (1 duty cycle) COFF 4848.5 where: R20 = resistance at 20°C where: Period 0.00393 °C 1 switching frequency T = operating temperature R = desired droop resistor value For temperature T = 50°C, the % R change = 12% Schottky Diode for Synchronous FET For synchronous operation, a Schottky diode may be placed in parallel with the synchronous FET to conduct the inductor current upon turn off of the switching FET to improve efficiency. The CS5166H reference circuit does not use this device due to it’s excellent design. Instead, the body diode of the synchronous FET is utilized to reduce cost and conducts the inductor current. For a design operating at 200 kHz or so, the low non–overlap time combined with Schottky forward recovery time may make the benefits of this device not worth the additional expense. The power dissipation in the synchronous MOSFET due to body diode conduction can be estimated by the following equation: Droop Resistor Tolerance Tolerance due to sheet resistivity variation Tolerance due to L/W error Tolerance due to temperature variation Total tolerance for droop resistor 16% 1.0% 12% 29% In order to determine the droop resistor value the nominal voltage drop across it at full load has to be calculated. This voltage drop has to be such that the output voltage full load is above the minimum DC tolerance spec. VDROOP(TYP) Power VBD ILOAD conduction time switching frequency [VDAC(MIN) VDC(MIN)] 1 RDROOP(TOLERANCE) Example: for a 300 MHz PentiumII, the DC accuracy spec is 2.74 < VCC(CORE) < 2.9 V, and the AC accuracy spec is Where VBD = the forward drop of the MOSFET body diode. For the CS5166H demonstration board: http://onsemi.com 17 CS5166H the regulator output is pre–positioned at 25 mV above the nominal output voltage before a load turn–on. The total voltage drop due to a load step is ∆V–25 mV and the deviation from the nominal output voltage is 25 mV smaller than it would be if there was no droop resistor. Similarly at full load the regulator output is pre–positioned at 18 mV below the nominal voltage before a load turn–off. The total voltage increase due to a load turn–off is ∆V–18 mV and the deviation from the nominal output voltage is 18 mV smaller than it would be if there was no droop resistor. This is because the output capacitors are pre–charged to value that is either 25 mV above the nominal output voltage before a load turn–on or, 18 mV below the nominal output voltage before a load turn–off (see Figure 16). Obviously, the larger the voltage drop across the droop resistor (the larger the resistance), the worse the DC and load regulation, but the better the AC transient response. 2.67 V < VCC(CORE) < 2.93 V. The CS5166H DAC output voltage is +2.796 V < VDAC < +2.853 V. In order not to exceed the DC accuracy spec, the voltage drop developed across the resistor must be calculated as follows: VDROOP(TYP) [VDAC(MIN) VDC PENTIUMII(MIN)] 1 RDROOP(TOLERANCE) 2.796 V 2.74 V 43 mV 1.3 With the CS5166H DAC accuracy being 1.0%, the internal error amplifier’s reference voltage is trimmed so that the output voltage will be 25 mV high at no load. With no load, there is no DC drop across the resistor, producing an output voltage tracking the error amplifier output voltage, including the offset. When the full load current is delivered, a drop of –43 mV is developed across the resistor. Therefore, VIN CS5166H IFB RFB Current Limit Comparator VFB + Q1 L RDROOP Q2 ISENSE VOUT COUT – VTH ISENSE RISENSE ISENSE Figure 30. Circuit Used to Determine the Voltage Across the Droop Resistor that will Trip the Internal Current Sense Comparator Current Limit Setpoint Calculations For 300 MHz Pentium II CPU the full load is 14.2 A. The internal current sense comparator current limit voltage limits are: 55 mV < VTH < 130 mV. Also, there is a 29% total variation in RSENSE as discussed in the previous section. We select the value of the current sensing element (embedded PCB trace) for the minimum current limit setpoint: The following is the design equations used to set the current limit trip point by determining the value of the embedded PCB trace used as a current sensing element. The current limit setpoint has to be higher than the normal full load current. Attention has to be paid to the current rating of the external power components as these are the first to fail during an overload condition. The MOSFET continuous and pulsed drain current rating at a given case temperature has to be accounted for when setting the current limit trip point. For example the IRL 3103S (D2 PAK) MOSFET has a continuous drain current rating of 45 A at VGS = 10 V and TC = 100°C. Temperature curves on MOSFET manufacturers’ data sheets allow the designer to determine the MOSFET drain current at a particular VGS and TJ (junction temperature). This, in turn, will assist the designer to set a proper current limit, without causing device breakdown during an overload condition. RSENSE(MAX) VTH(MIN) RSENSE 1.29 55 mV 14.2 A ICL(MIN) RSENSE 1.29 3.87 m RSENSE 3.0 m We calculate the range of load currents that will cause the internal current sense comparator to detect and overload condition. From the overcurrent detection data section on page 3. Nominal Current Limit Setpoint VTH(TYP) 76 mV http://onsemi.com 18 CS5166H ICL(NOM) R The value of RSENSE (current sense PCB trace) is then calculated: VTH(TYP) SENSE(NOM) RSENSE(MAX) 58.3 mV 4.1 m 14.2 A Maximum Current Limit Setpoint Therefore, ICL(NOM) 76 mV 25.3 3.0 m RSENSE(NOM) VTH(MAX) 110 mV RSENSE(MAX) 4.1 mm 3.18 m 1.29 1.29 The range of load currents that will cause the internal current sense comparator to detect an overload condition is as follows: Nominal Current Limit Setpoint Therefore, ICL(MAX) 110 mV 110 mV 110 mV 51.6 A 3.0 m 0.71 RSENSE(MIN) RSENSE 0.71 VTRIP(NOM) ICL(NOM) RSENSE(NOM) Therefore, the range of load currents that will cause the internal current sense comparator to detect an overload condition through a 3.0 mΩ embedded PCB trace is: 14.2 A < ICL < 51.6 A, with 25.3 A being the nominal overload condition. There may be applications whose layout will require the use of two extra filter components, a 510 Ω resistor in series with the ISENSE pin, and a 0.1 µF capacitor between the ISENSE and VFB pins. These are needed for proper current limit operation and the resistor value is layout dependent. This series resistor affects the calculation of the current limit setpoint, and has to be taken into account when determining an effective current limit. The calculations below show how the current limit setpoint is determined when this 510 Ω is taken into consideration. Therefore, ICL(NOM) 90.97 mV 28.6 A 3.18 m Maximum Current Limit Setpoint VTRIP(MAX) ICL(MAX) RSENSE(MAX) Therefore, 135 mV ICL(MAX) 60 A 3.18 m 0.71 Therefore, the range of load currents that will cause the internal current sense comparator to detect an overload condition through a 3.0 mΩ embedded PCB trace is: 14.2 A < ICL 60 A, with 28.6 A being the nominal overload condition. VTRIP VTH (ISENSE RISENSE) (RFB IFB) Design Rules for Using a Droop Resistor Where: VTRIP = voltage across the droop resistor that trips the ISENSE comparator. VTH = internal ISENSE comparator threshold ISENSE = ISENSE bias current RISENSE = ISENSE pin 510 Ω filter resistor RFB = VFB pin 3.3 k filter resistor IFB = VFB bias current Minimum current sense resistor (droop resistor) voltage drop required for current limit when RISENSE is used The basic equation for laying an embedded resistor is: L RAR L or R A (W t) where: A = W × t = cross–sectional area ρ = the copper resistivity (µΩ – mil) L = length (mils) W = width (mils) t = thickness (mils) VTRIP(MIN) 55 mV (13 A 510) (3.3 k 1.0 A) For most PCBs the copper thickness, t, is 35 µm (1.37 mils) for one ounce copper. ρ = 717.86 µΩ–mil For a Pentium II load of 14.2 A the resistance needed to create a 43 mV drop at full load is: 55 mV 6.6 mV 3.3 mV 58.3 mV Nominal current sense resistor (droop resistor) voltage drop required for current limit when RISENSE is used VTRIP(NOM) 76 mV (30 A 510) (3.3 k 0.1 A) Response Droop 43 mV 43 mV 3.0 m 14.2 A IOUT 76 mV 15.3 mV 0.33 mV 90.97 mV The resistivity of the copper will drift with the temperature according to the following guidelines: Maximum current sense resistor (droop resistor) voltage drop required for current limit when RISENSE is used R 12% @ TA 50°C VTRIP(NOM) 110 mV (50 A 510) 110 mV 25.5 mV 135.5 mV R 34% @ TA 100°C http://onsemi.com 19 CS5166H 5.0 V 1200 µF/10 V × 3 12 V IRL3103S 1.0 µF COFF SS 0.1 µF COMP VID0 0.1 µF CS5166H 330 pF VCC GATE(H) 1.2 µH 3.0 mΩ 510 ISENSE 1200 µF/ 10 V × 5 0.1 µF IRL3103S GATE(L) VID1 VID2 PGND VID3 LGND 2.8 V/30 A Power Supply PWRGD 3.3 k VID4 PWRGD VFB VID4 VID3 1000 pF VID2 VID1 VID0 5.0 V 1200 µF/ 10 V × 3 12 V 1.0 µF IRL3103S 330 pF 0.1 µF COMP VID0 VID1 VID2 CS5166H VCC GATE(H) COFF SS 1.2 µH 3.0 mΩ 510 ISENSE 0.1 µF IRL3103S GATE(L) PGND VID3 LGND VID4 VFB 3.3 k 1000 pF Figure 31. Current Sharing of a 2.8 V/30 A Power Supply Using Two CS5166H Synchronous Buck Regulators Droop Resistor Width Calculations W 14.2 A 284 mils 0.7213 cm 0.05 The droop resistor must have the ability to handle the load current and therefore requires a minimum width which is calculated as follows (assume one ounce copper thickness): Droop Resistor Length Calculation L I W LOAD 0.05 RDROOP W t 0.0030 284 1.37 1626 mil 4.13 cm 717.86 where: W = minimum width (in mils) required for proper power dissipation, and ILOAD Load Current Amps. The Pentium II maximum load current is 14.2 A. Therefore: http://onsemi.com 20 CS5166H Implementing Current Sharing Using the “Droop Resistor” sharing accuracy will be determined solely by their matching. To realize the benefits of current sharing, it is not necessary to obtain perfect matching. Keeping output currents within ± 10% is usually acceptable. For microprocessor applications, the value of the droop resistor must be selected to optimize adaptive voltage positioning, current sharing, current limit and efficiency. Current sharing is realized by simply connecting the COMP pins of the respective buck regulators, as shown in Figure 31. Figure 32 shows operation with no load. In this case, there is insufficient output voltage ripple across the droop resistor to produce complete synchronization. Duty Cycle is close to the theoretical 56% (VOUT/VIN) resulting in a switching frequency of approximately 275 kHz. Figure 34 shows operation with a 30 Amp load. Synchronization between the two regulators is now obtained due to increased ripple voltage. Increases losses cause the V2 control loop to increase on–time to compensate. This results in a larger duty cycle and a corresponding decrease in switching frequency to 233 kHz. In addition to improving load transient performance, the CS5166H V2 control method allows the droop resistor to provide the additional capability to easily implement current sharing. Figure 31 shows a simplified schematic of two current sharing synchronous buck regulators. Each buck regulator’s droop resistor is terminated at the load. The PWM control signal from each Error Amp is connected together, causing the inner PWM loop to regulate to a common voltage. Since the voltage at each resistor terminal is the same, this configuration results in equal voltage being applied across each matched droop resistor. The result is equal current flowing through each buck regulator. An additional benefit is that synchronization to a common switching frequency tends to be achieved because each regulator shares a common PWM ramp signal. In practice, each buck regulator will regulate to a slightly different output voltage due to mismatching of the PWM comparators, slope of the PWM ramp (output voltage ripple), and propagation delays. At light loads, the results can be very poor current sharing. With zero output current, some regulators may be sourcing current while others may be sinking current. This results in additional power dissipation and lower efficiency than would be obtained by a single regulator. This is usually not an issue since efficiency is most important when a supply is fully loaded. This effect is similar to the difference in efficiency between synchronous and non–synchronous buck regulators. Synchronous buck regulators have lower efficiency at light loads because inductor current is always continuous, flowing from the load to ground during switch off–time through the synchronous rectifier. Under full load conditions, the synchronous design is more efficient due to the lower voltage drop across the synchronous rectifier. Likewise, the efficiency of droop sharing regulators will be lower at light loads due to the continuous current flow in the droop resistors. Efficiency at heavy loads tends to be higher due to reduced I2R losses. The output current of each regulator can be calculated from: IN Trace 1 = Output voltage ripple. Trace 2 = Buck regulator #1 inductor switching node. Trace 3 = Buck regulator #2 inductor switching node. Figure 32. No Load Waveforms (VOUT(N) VOUT) RDROOP(N) where: VOUT(N) and RDROOP(N) are the output voltage and droop resistance of a particular regulator and VOUT is the system output voltage. Output current is the sum of each regulator’s current: IOUT I1 I2 IN Current sharing improves with increasing load current. The increasing voltage drop across the droop resistor due to increasing load current eventually swamps out the differences in regulator output voltages. If a large enough voltage can be developed across the droop resistors, current Trace 1 = Output voltage ripple. Trace 2 = Buck regulator #1 inductor switching node. Trace 3 = Buck regulator #2 inductor switching node. Figure 33. 15 A Load Transient Waveforms http://onsemi.com 21 CS5166H ESR VOUT IOUT This applies for current spikes that are faster than regulator response time. Printed Circuit Board resistance will add to the ESR of the output capacitors. In order to limit spikes to 100 mV for a 14.2 A Load Step, ESR = 0.1/14.2 = 0.007 Ω Inductor Peak Current Peak Current Maximum Load Current Example: VIN = +5.0 V, VOUT = +2.8 V, ILOAD = 14.2 A, L = 1.2 µH, Freq = 200 kHz Trace 1 = Output voltage ripple. Trace 2 = Buck regulator #1 inductor switching node. Peak Current 14.2 A (5.12) 16.75 A Trace 3 = Buck regulator #2 inductor switching node. Figure 34. 30 A Load Waveforms A key consideration is that the inductor must be able to deliver the Peak Current at the switching frequency without saturating. Figure 33 shows supply response to a 15 A load step with a 30 A/µs slew rate. The V2 control loop immediately forces the duty cycle to 100%, ramping the current in both inductors up. A voltage spike of 136 mV due to output capacitor impedance occurs. The inductive component of the spike due to ESL recovers within several microseconds. The resistive component due to ESR decreases as inductor current replaces capacitor current. The benefit of adaptive voltage positioning in reducing the voltage spike can readily be seen. The difference in DC voltage and duty cycle can also be observed. This particular transient occurred near the beginning of regulator off time, resulting in a longer recovery time and increased voltage spike. Response Time to Load Increase (limited by Inductor value unless Maximum On–Time is exceeded) Response Time L IOUT (VIN VOUT) Example: VIN = +5.0 V, VOUT = +2.8 V, L = 1.2 µH, 14.2 A change in Load Current Response Time 1.2 H 14.2 A 7.7 s (5.0 V 2.8 V) Response Time to Load Decrease Output Inductor (limited by Inductor value) The inductor should be selected based on its inductance, current capability, and DC resistance. Increasing the inductor value will decrease output voltage ripple, but degrade transient response. Response Time L Change in IOUT VOUT Example: VOUT = +2.8 V, 14.2 A change in Load Current, L = 1.2 µH Inductor Ripple Current Ripple Current Ripple 2Current [(VIN VOUT) VOUT] (Switching Frequency L VIN) Response Time Example: VIN = +5.0 V, VOUT = +2.8 V, ILOAD = 14.2 A, L = 1.2 µH, Freq = 200 kHz 1.2 H 14.2 A 6.1 s 2.8 V Input and Output Capacitors These components must be selected and placed carefully to yield optimal results. Capacitors should be chosen to provide acceptable ripple on the input supply lines and regulator output voltage. Key specifications for input capacitors are their ripple rating, while ESR is important for output capacitors. For best transient response, a combination of low value/high frequency and bulk capacitors placed close to the load will be required. [(5.0 V 2.8 V) 2.8 V] Ripple Current 5.1 A [200 kHz 1.2 H 5.0 V] Output Ripple Voltage VRIPPLE Inductor Ripple Current Output Capacitor ESR Example: VIN = +5.0 V, VOUT = +2.8 V, ILOAD = 14.2 A, L = 1.2 µH, Switching Frequency = 200 kHz Output Ripple Voltage = 5.1 A × Output Capacitor ESR (from manufacturer’s specs) ESR of Output Capacitors to limit Output Voltage Spikes http://onsemi.com 22 CS5166H Layout Guidelines THERMAL MANAGEMENT When laying out the CPU buck regulator on a printed circuit board, the following checklist should be used to ensure proper operation of the CS5166H. 1. Rapid changes in voltage across parasitic capacitors and abrupt changes in current in parasitic inductors are major concerns for a good layout. 2. Keep high currents out of sensitive ground connections. Avoid connecting the IC GND (LGND) between the source of the lower FET and the input capacitor GND. 3. Avoid ground loops as they pick up noise. Use star or single point grounding. 4. For high power buck regulators on double–sided PCBs a single large ground plane (usually the bottom) is recommended. 5. Even though double sided PCBs are usually sufficient for a good layout, four–layer PCBs are the optimum approach to reducing susceptibility to noise. Use the two internal layers as the +5.0 V and GND planes, the top layer for the power connections and component vias, and the bottom layer for the noise sensitive traces. 6. Keep the inductor switching node small by placing the output inductor, switching and synchronous FETs close together. 7. The FET gate traces to the IC must be as short, straight, and wide as possible. Ideally, the IC has to be placed right next to the FETs. 8. Use fewer, but larger output capacitors, keep the capacitors clustered, and use multiple layer traces with heavy copper to keep the parasitic resistance low. 9. Place the switching FET as close to the +5.0 V input capacitors as possible. 10. Place the output capacitors as close to the load as possible. 11. Place the VFB filter resistor in series with theVFB pin (pin 16) right at the pin. 12. Place the VFB filter capacitor right at the VFB pin (pin 16). 13. The “Droop” Resistor (embedded PCB trace) has to be wide enough to carry the full load current. 14. Place the VCC bypass capacitor as close as possible to the VCC pin and connect it to the PGND pin of the IC. Connect the PGND pin directly to the GND plane. 15. Create a subground (local GND) plane preferably on the PCB top layer and under the IC controller. Connect all logic capacitor returns and the LGND pin of the IC to this place. Connect the subground plane to the main GND plane using a minimum of four (4) vias. Thermal Considerations for Power MOSFETs and Diodes In order to maintain good reliability, the junction temperature of the semiconductor components should be kept to a maximum of 150°C or lower. The thermal impedance (junction to ambient) required to meet this requirement can be calculated as follows: Thermal Impedance TJ(MAX) TA Power A heatsink may be added to TO–220 components to reduce their thermal impedance. A number of PC board layout techniques such as thermal vias and additional copper foil area can be used to improve the power handling capability of surface mount components. EMI Management As a consequence of large currents being turned on and off at high frequency, switching regulators generate noise as a consequence of their normal operation. When designing for compliance with EMI/EMC regulations, additional components may be added to reduce noise emissions. These components are not required for regulator operation and experimental results may allow them to be eliminated. The input filter inductor may not be required because bulk filter and bypass capacitors, as well as other loads located on the board will tend to reduce regulator di/dt effects on the circuit board and input power supply. Placement of the power component to minimize routing distance will also help to reduce emissions. 2.0 µH 33 Ω 1000 pF Figure 35. Filter Components 2.0 µH + 1200 µF × 3.0/16 V Figure 36. Input Filter http://onsemi.com 23 CS5166H +12 V +12 V 1N5818 1200 µF/16 V × 3 1N5818 0.1 µF 18 Ω 18 V 1N4746 1.0 µF Droop Resistor IRL3103S (Embedded PCB trace) VCC COFF 1000 pF GATE(H) SS CS5166H VFB COMP 0.1 µF 0.1 µF 1.2 µH 3.0 mΩ VCC 3.3 k 1000 pF IRL3103S GATE(L) VID0 VID1 PGND VID2 VID3 LGND VID4 ISENSE PWRGD 1200 µF/10 V ×5 VSS PWRGD 0.1 µF PENTIUM II SYSTEM 510 VID4 VID3 VID2 VID1 VID0 Figure 37. Additional Application Diagram, +12 V to +2.8 V @ 14.2 A for 300 MHz Pentium II +5.0 V MBRS120 1.0 µF MBRS120 1200 µF/10 V × 3 MBRS120 1.0 µF VCC VID0 VID1 VGATE(L) VID3 VID4 3.0 mΩ VCC COFF SS VSS 510 ISENSE PWRGD 0.1 µF VFB LGND 0.1 µF 1200 µF/10 V ×5 IRL3103S PGND COMP 0.1 µF 1.2 µH CS5166H VID2 330 pF VGATE(H) Droop Resistor (Embedded PCB trace) IRL3103S 3.3 k PWRGD PENTIUM II SYSTEM 1000 pF VID4 VID3 VID2 VID1 VID0 Figure 38. Additional Application Diagram, +5.0 V to +2.8 V @ 14.2 A for 300 MHz Pentium II http://onsemi.com 24 CS5166H PACKAGE DIMENSIONS SO–16L DW SUFFIX CASE 751G–03 ISSUE B A D 9 1 8 NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DIMENSIONS D AND E DO NOT INLCUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. 16X T A M S B h X 45 S 14X e L A 0.25 DIM A A1 B C D E e H h L B B A1 H E 0.25 8X M B M 16 SEATING PLANE T C PACKAGE THERMAL DATA SO–16L Unit RΘJC Parameter Typical 23 °C/W RΘJA Typical 105 °C/W http://onsemi.com 25 MILLIMETERS MIN MAX 2.35 2.65 0.10 0.25 0.35 0.49 0.23 0.32 10.15 10.45 7.40 7.60 1.27 BSC 10.05 10.55 0.25 0.75 0.50 0.90 0 7 CS5166H Notes http://onsemi.com 26 CS5166H Notes http://onsemi.com 27 CS5166H V2 is a trademark of Switch Power, Inc. Pentium is a registered trademark of Intel Corporation. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada Email: [email protected] Fax Response Line: 303–675–2167 or 800–344–3810 Toll Free USA/Canada N. American Technical Support: 800–282–9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor – European Support German Phone: (+1) 303–308–7140 (Mon–Fri 2:30pm to 7:00pm CET) Email: ONlit–[email protected] French Phone: (+1) 303–308–7141 (Mon–Fri 2:00pm to 7:00pm CET) Email: ONlit–[email protected] English Phone: (+1) 303–308–7142 (Mon–Fri 12:00pm to 5:00pm GMT) Email: [email protected] CENTRAL/SOUTH AMERICA: Spanish Phone: 303–308–7143 (Mon–Fri 8:00am to 5:00pm MST) Email: ONlit–[email protected] Toll–Free from Mexico: Dial 01–800–288–2872 for Access – then Dial 866–297–9322 ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support Phone: 1–303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong & Singapore: 001–800–4422–3781 Email: ONlit–[email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031 Phone: 81–3–5740–2700 Email: [email protected] ON Semiconductor Website: http://onsemi.com EUROPEAN TOLL–FREE ACCESS*: 00–800–4422–3781 *Available from Germany, France, Italy, UK, Ireland For additional information, please contact your local Sales Representative. http://onsemi.com 28 CS5166H/D