CYPRESS CY22150FZXC

CY22150
One-PLL General-Purpose
Flash-Programmable and 2-Wire Serially
Programmable Clock Generator
Features
■
Nonvolatile reprogrammable technology allows easy customization, quick turnaround on design changes and product performance enhancements, and better inventory control. Parts can
be reprogrammed up to 100 times, reducing inventory of
custom parts and providing an easy method for upgrading
existing designs.
■
The CY22150 can be programmed at the package level.
In-house programming of samples and prototype quantities is
available using the CY3672 FTG Development Kit. Production
quantities are available through Cypress’s value added distribution partners or by using third party programmers from BP
Microsystems‰, HiLo Systems‰, and others.
■
Internal PLL to generate six outputs up to 200 MHz. Able to
generate custom frequencies from an external crystal or
a driven source.
The CY22150 provides an industry standard interface for
volatile, system level customization of unique frequencies and
options. Serial programming and reprogramming allows quick
design changes and product enhancements, eliminates
inventory of old design parts, and simplifies manufacturing.
■
High performance suited for commercial, industrial,
networking, telecom, and other general purpose applications.
Performance guaranteed for applications that require an
extended temperature range.
■
Application compatibility in standard and low power systems.
■
Industry standard packaging saves on board space.
■
Integrated phase-locked loop (PLL)
■
Commercial and industrial operation
■
Flash programmable
■
Field programmable
■
Two-wire serial programming interface
■
Low skew, low jitter, high accuracy outputs
■
3.3V operation with 2.5V output option
■
16-pin TSSOP
Benefits
■
■
Part Number
Outputs
Input Frequency Range
Output Frequency Range
Specifications
CY22150FC
6
8 MHz to 30 MHz (external crystal)
1 MHz to 133 MHz (driven clock)
80 kHz to 200 MHz (3.3V)
80 KHz to 166.6 MHz (2.5V)
Field programmable
Serially programmable
Commercial temperature
CY22150FI
6
8 MHz to 30 MHz (external crystal)
1 MHz to 133 MHz (driven clock)
80 kHz to 166.6 MHz (3.3V)
80 KHz to 150 MHz (2.5V)
Field programmable
Serially programmable
Industrial temperature
Logic Block Diagram
LCLK1
Divider
Bank 1
XIN
OSC.
Q
Φ
VCO
XOUT
LCLK2
Crosspoint
Switch
Matrix
LCLK3
LCKL4
P
Divider
Bank 2
PLL
Serial
SDAT
Programming
SCLK
Interface
CLK5
CLK6
SPI
Control
VDD VSS AVDD AVSS VDDL VSSL
Cypress Semiconductor Corporation
Document #: 38-07104 Rev. *I
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised January 23, 2009
[+] Feedback
CY22150
Pin Configuration
Figure 1. 16-Pin TSSOP
XIN
1
16
XOUT
VDD
2
15
CLK6
AVDD
3
14
CLK5
SDAT
4
13
AVSS
5
12
VSSL
6
11
LCLK1
LCLK2
7
10
8
9
VSS
LCLK4
VDDL
SCLK
LCLK3
Table 1. Pin Definitions
Name
Number
Description
XIN
1
Reference Input. Driven by a crystal (8 MHz to 30 MHz) or external clock (1 MHz to 133 MHz).
Programmable input load capacitors allow for maximum flexibility in selecting a crystal,
regardless of manufacturer, process, performance, or quality
VDD
2
3.3V Voltage Supply
AVDD
3
3.3V Analog Voltage Supply
SDAT
4
Serial Data Input
AVSS
5
Analog Ground
VSSL
6
LCLK Ground
LCLK1
7
Configurable Clock Output 1 at VDDL level (3.3V or 2.5V)
LCLK2
8
Configurable Clock Output 2 at VDDL level (3.3V or 2.5V)
LCLK3
9
Configurable Clock Output 3 at VDDL level (3.3V or 2.5V)
SCLK
10
Serial Clock Output
VDDL
11
LCLK Voltage Supply (2.5V or 3.3V)
LCLK4
12
Configurable Clock Output 4 at VDDL level (3.3V or 2.5V)
VSS
13
Ground
CLK5
14
Configurable Clock Output 5 (3.3V)
CLK6
15
Configurable Clock Output 6 (3.3V)
XOUT[1]
16
Reference Output
Note
1. Float XOUT if XIN is driven by an external clock source.
Document #: 38-07104 Rev. *I
Page 2 of 16
[+] Feedback
CY22150
Frequency Calculation and Register Definitions
The CY22150 is an extremely flexible clock generator with four
basic variables that are used to determine the final output
frequency. They are the input reference frequency (REF), the
internally calculated P and Q dividers, and the post divider, which
can be a fixed or calculated value. There are three formulas to
determine the final output frequency of a CY22150 based
design:
■
CLK = ((REF * P)/Q)/Post Divider
■
CLK = REF/Post Divider
■
CLK = REF.
The basic PLL block diagram is shown in Figure 2. Each of the
six clock outputs on the CY22150 has a total of seven output
options available to it. There are six post divider options
available: /2 (two of these), /3, /4, /DIV1N and /DIV2N. DIV1N
and DIV2N are independently calculated and are applied to
individual output groups. The post divider options can be applied
to the calculated VCO frequency ((REF*P)/Q) or to the REF
directly.
In addition to the six post divider output options, the seventh
option bypasses the PLL and passes the REF directly to the
crosspoint switch matrix.
Figure 2. Basic Block Diagram of CY22150 PLL
DIV1N [OCH]
CLKSRC
Crosspoint
Switch Matrix
DIV1SRC [OCH]
1
Qtotal
(Q+2)
PFD
VCO
[42H]
Ptotal
DIV1CLK
REF
0
/DIV1N
[44H]
LCLK2
[44H,45H]
LCLK3
[45H]
LCLK4
[45H]
CLK5
[45H,46H]
CLK6
Divider Bank 1
Divider Bank 2
[40H], [41H], [42H]
1
DIV2CLK
0
LCLK1
/2
/3
(2(PB+4)+PO)
[44H]
/4
/2
/DIV2N
DIV2SRC [47H]
DIV2N [47H]
CLKOE [09H]
Document #: 38-07104 Rev. *I
Page 3 of 16
[+] Feedback
CY22150
Default Startup Condition for the CY22150
Table 2 lists the SPI registers and their definitions. Specific
register definitions and their allowable values are listed below.
The default (programmed) condition of the device is generally set
by the distributor who programs the device using a customer
specific JEDEC file produced by CyClocksRT™. Parts shipped
from the factory are blank and unprogrammed. In this condition,
all bits are set to 0, all outputs are three-stated, and the crystal
oscillator circuit is active.
Reference Frequency
The REF can be a crystal or a driven frequency. For crystals, the
frequency range must be between 8 MHz and 30 MHz. For a
driven frequency, the frequency range must be between 1 MHz
and 133 MHz.
While you can develop your own subroutine to program any or
all of the individual registers described in the following pages, it
may be easier to use CyClocksRT to produce the required
register setting file.
Using a Crystal as the Reference Input
The input crystal oscillator of the CY22150 is an important
feature because of the flexibility it allows the user in selecting a
crystal as a REF source. The input oscillator has programmable
gain, allowing maximum compatibility with a reference crystal,
regardless of manufacturer, process, performance, and quality.
The serial interface address of the CY22150 is 69H. If there is a
conflict with any other devices in your system, then this can also
be changed using CyClocksRT.
Programmable Crystal Input Oscillator Gain Settings
Frequency Calculations and Register Definitions using the Serial Programming Interface
The Input crystal oscillator gain (XDRV) is controlled by two bits
in register 12H and are set according to Table 3 on page 5. The
parameters controlling the gain are the crystal frequency, the
internal crystal parasitic resistance (ESR, available from the
manufacturer), and the CapLoad setting during crystal startup.
The CY22150 provides an industry standard serial interface for
volatile, in-system programming of unique frequencies and
options. Serial programming and reprogramming allows for quick
design changes and product enhancements, eliminates
inventory of old design parts, and simplifies manufacturing.
Bits 3 and 4 of register 12H control the input crystal oscillator gain
setting. Bit 4 is the MSB of the setting, and bit 3 is the LSB. The
setting is programmed according to Table 3 on page 5. All other
bits in the register are reserved and should be programmed as
shown in Table 4 on page 5.
The Serial Programming Interface (SPI) provides volatile
programming. This means when the target system is powered
down, the CY22150 reverts to its pre-SPI state, as defined above
(programmed or unprogrammed). When the system is powered
back up again, the SPI registers must be reconfigured again.
Using an External Clock as the Reference Input
The CY22150 also accepts an external clock as reference, with
speeds up to 133 MHz. With an external clock, the XDRV
(register 12H) bits must be set according to Table 5 on page 5.
All programmable registers in the CY22150 are addressed with
eight bits and contain eight bits of data. The CY22150 is a slave
device with an address of 1101001 (69H).
Table 2. Summary Table – CY22150 Programmable Registers
Register
Description
09H
CLKOE control
OCH
DIV1SRC mux and
DIV1N divider
12H
Input crystal oscillator
drive control
13H
Input load capacitor
control
40H
Charge pump and PB
counter
41H
42H
PO counter, Q counter
44H
Crosspoint switch
matrix control
D7
D6
D5
D4
D3
D2
D1
D0
0
0
CLK6
CLK5
LCLK4
LCLK3
LCLK2
LCLK1
DIV1SRC
DIV1N(6)
DIV1N(5)
DIV1N(4)
DIV1N(3)
DIV1N(2)
DIV1N(1)
DIV1N(0)
0
0
1
XDRV(1)
XDRV(0)
0
0
0
CapLoad
(7)
CapLoad
(6)
CapLoad
(5)
CapLoad
(4)
CapLoad
(3)
CapLoad
(2)
CapLoad
(1)
CapLoad
(0)
1
1
0
Pump(2)
Pump(1)
Pump(0)
PB(9)
PB(8)
PB(7)
PB(6)
PB(5)
PB(4)
PB(3)
PB(2)
PB(1)
PB(0)
PO
Q(6)
Q(5)
Q(4)
Q(3)
Q(2)
Q(1)
Q(0)
CLKSRC2 CLKSRC1 CLKSRC0 CLKSRC2 CLKSRC1 CLKSRC0 CLKSRC2 CLKSRC1
for LCLK1 for LCLK1 for LCLK1 for LCLK2 for LCLK2 for LCLK2 for LCLK3 for LCLK3
45H
CLKSRC0 CLKSRC2 CLKSRC1 CLKSRC0 CLKSRC2 CLKSRC1 CLKSRC0 CLKSRC2
for LCLK3 for LCLK4 for LCLK4 for LCLK4 for CLK5 for CLK5 for CLK5 for CLK6
46H
CLKSRC1 CLKSRC0
for CLK6 for CLK6
47H
DIV2SRC mux and
DIV2N divider
Document #: 38-07104 Rev. *I
DIV2SRC
DIV2N(6)
1
1
1
1
1
1
DIV2N(5)
DIV2N(4)
DIV2N(3)
DIV2N(2)
DIV2N(1)
DIV2N(0)
Page 4 of 16
[+] Feedback
CY22150
Table 3. Programmable Crystal Input Oscillator Gain Settings
Cap Register Settings
00H – 80H
80H – C0H
C0H – FFH
Effective Load Capacitance
(CapLoad)
6 pF to 12 pF
12 pF to 18 pF
18 pF to 30 pF
Crystal Input
Frequency
Crystal ESR
30Ω
60Ω
30Ω
60Ω
30Ω
60Ω
8 to 15 MHz
00
01
01
10
01
10
15 to 20 MHz
01
10
01
10
10
10
20 to 25 MHz
01
10
10
10
10
11
25 to 30 MHz
10
10
10
11
11
N/A
Table 4. Bit Locations and Values
Address
D7
D6
D5
D4
D3
D2
D1
D0
12H
0
0
1
XDRV(1)
XDRV(0)
0
0
0
Table 5. Programmable External Reference Input Oscillator Drive Settings
Reference Frequency
1 to 25 MHz
25 to 50 MHz
50 to 90 MHz
90 to 133 MHz
00
01
10
11
Drive Setting
Input Load Capacitors
PLL Frequency, Q Counter [42H(6..0)]
Input load capacitors allow the user to set the load capacitance
of the CY22150 to match the input load capacitance from a
crystal. The value of the input load capacitors is determined by
8 bits in a programmable register [13H]. Total load capacitance
is determined by the formula:
The first counter is known as the Q counter. The Q counter
divides REF by its calculated value. Q is a 7 bit divider with a
maximum value of 127 and minimum value of 0. The primary
value of Q is determined by 7 bits in register 42H (6..0), but 2 is
added to this register value to achieve the total Q, or Qtotal. Qtotal
is defined by the formula:
CapLoad = (CL– CBRD – CCHIP)/0.09375 pF
where:
Qtotal = Q + 2
■
CL = specified load capacitance of your crystal.
The minimum value of Qtotal is 2. The maximum value of Qtotal is
129. Register 42H is defined in the table.
■
CBRD = the total board capacitance, due to external capacitors
and board trace capacitance. In CyClocksRT, this value
defaults to 2 pF.
Stable operation of the CY22150 cannot be guaranteed if
REF/Qtotal falls below 250 kHz. Qtotal bit locations and values are
defined in Table 7 on page 6.
■
CCHIP = 6 pF.
■
0.09375 pF = the step resolution available due to the 8-bit
register.
In CyclocksRT, only the crystal capacitance (CL) is specified.
CCHIP is set to 6 pF and CBRD defaults to 2 pF. If your board
capacitance is higher or lower than 2 pF, the formula given earlier
is used to calculate a new CapLoad value and programmed into
register 13H.
In CyClocksRT, enter the crystal capacitance (CL). The value of
CapLoad is determined automatically and programmed into the
CY22150. Through the SDAT and SCLK pins, the value can be
adjusted up or down if your board capacitance is greater or less
than 2 pF. For an external clock source, CapLoad defaults to 0.
See Table 6 on page 6 for CapLoad bit locations and values.
The input load capacitors are placed on the CY22150 die to
reduce external component cost. These capacitors are true
parallel-plate capacitors, designed to reduce the frequency shift
that occurs when nonlinear load capacitance is affected by load,
bias, supply, and temperature changes.
Document #: 38-07104 Rev. *I
PLL Frequency, P Counter [40H(1..0)], [41H(7..0)],
[42H(7)
The next counter definition is the P (product) counter. The P
counter is multiplied with the (REF/Qtotal) value to achieve the
VCO frequency. The product counter, defined as Ptotal, is made
up of two internal variables, PB and PO. The formula for calculating Ptotal is:
Ptotal = (2(PB + 4) + PO)
PB is a 10-bit variable, defined by registers 40H(1:0) and
41H(7:0). The 2 LSBs of register 40H are the two MSBs of
variable PB. Bits 4..2 of register 40H are used to determine the
charge pump settings. The 3 MSBs of register 40H are preset
and reserved and cannot be changed. PO is a single bit variable,
defined in register 42H(7). This allows for odd numbers in Ptotal.
The remaining seven bits of 42H are used to define the Q
counter, as shown in Table 7.
The minimum value of Ptotal is 8. The maximum value of Ptotal is
2055. To achieve the minimum value of Ptotal, PB and PO should
both be programmed to 0. To achieve the maximum value of
Ptotal, PB should be programmed to 1023, and PO should be
programmed to 1.
Page 5 of 16
[+] Feedback
CY22150
of DIVxN is 127. A value of DIVxN below 4 is not guaranteed to
work properly.
Stable operation of the CY22150 cannot be guaranteed if the
value of (Ptotal*(REF/Qtotal)) is above 400 MHz or below
100 MHz. Registers 40H, 41H, and 42H are defined in Table 8.
PLL Post Divider Options [OCH(7..0)], [47H(7..0)]
DIV1SRC is a single bit variable, controlled by register OCH. The
remaining seven bits of register OCH determine the value of post
divider DIV1N.
The output of the VCO is routed through two independent
muxes, then to two divider banks to determine the final clock
output frequency. The mux determines if the clock signal feeding
into the divider banks is the calculated VCO frequency or REF.
There are two select muxes (DIV1SRC and DIV2SRC) and two
divider banks (Divider Bank 1 and Divider Bank 2) used to
determine this clock signal. The clock signal passing through
DIV1SRC and DIV2SRC is referred to as DIV1CLK and
DIV2CLK, respectively.
DIV2SRC is a single bit variable, controlled by register 47H. The
remaining seven bits of register 47H determine the value of post
divider DIV2N.
Register OCH and 47H are defined in Table 9.
Charge Pump Settings [40H(2..0)]
The correct pump setting is important for PLL stability. Charge
pump settings are controlled by bits (4..2) of register 40H, and
are dependent on internal variable PB (see “PLL Frequency, P
Counter[40H(1..0)], [41H(7..0)], [42H(7)]”). Table 10 on page 6
summarizes the proper charge pump settings, based on Ptotal.
The divider banks have four unique divider options available: /2,
/3, /4, and /DIVxN. DIVxN is a variable that can be independently
programmed (DIV1N and DIV2N) for each of the two divider
banks. The minimum value of DIVxN is 4. The maximum value
See Table 11 on page 7 for register 40H bit locations and values.
Table 6. Input Load Capacitor Register Bit Settings
Address
D7
D6
D5
D4
D3
D2
D1
D0
13H
CapLoad(7)
CapLoad(6)
CapLoad(5)
CapLoad(4)
CapLoad(3)
CapLoad(2)
CapLoad(1)
CapLoad(0)
D5
D4
D3
D2
D1
D0
Table 7. P Counter Register Definition
Address
D7
D6
40H
1
1
0
Pump(2)
Pump(1)
Pump(0)
PB(9)
PB(8)
41H
PB(7)
PB(6)
PB(5)
PB(4)
PB(3)
PB(2)
PB(1)
PB(0)
42H
PO
Q(6)
Q(5)
Q(4)
Q(3)
Q(2)
Q(1)
Q(0)
D5
D4
D3
D2
D1
D0
Table 8. P Counter Register Definition
Address
D7
D6
40H
1
1
0
Pump(2)
Pump(1)
Pump(0)
PB(9)
PB(8)
41H
PB(7)
PB(6)
PB(5)
PB(4)
PB(3)
PB(2)
PB(1)
PB(0)
42H
PO
Q(6)
Q(5)
Q(4)
Q(3)
Q(2)
Q(1)
Q(0)
Table 9. PLL Post Divider Options
Address
D7
D6
D5
D4
D3
D2
D1
D0
OCH
DIV1SRC
DIV1N(6)
DIV1N(5)
DIV1N(4)
DIV1N(3)
DIV1N(2)
DIV1N(1)
DIV1N(0)
47H
DIV2SRC
DIV2N(6)
DIV2N(5)
DIV2N(4)
DIV2N(3)
DIV2N(2)
DIV2N(1)
DIV2N(0)
Table 10. Charge Pump Settings
Charge Pump Setting – Pump(2..0)
Calculated Ptotal
000
16 – 44
001
45 – 479
010
480 – 639
011
640 – 799
100
800 – 1023
101, 110, 111
Do not use – device will be unstable
Document #: 38-07104 Rev. *I
Page 6 of 16
[+] Feedback
CY22150
Table 11. Register 40H Change Pump Bit Settings
Address
D7
D6
D5
D4
D3
D2
D1
D0
40H
1
1
0
Pump(2)
Pump(1)
Pump(0)
PB(9)
PB(8)
Although using the above table guarantees stability, it is recommended to use the Print Preview function in CyClocksRT to
determine the correct charge pump settings for optimal jitter
performance.
CLKSRC(0,0,1). When DIV1N is six, then CLKSRC(0,1,1) is
guaranteed to be rising edge phase-aligned with
CLKSRC(0,0,1).
When DIV2N is divisible by four, then CLKSRC(1,0,1) is
guaranteed to be rising edge phase-aligned with
CLKSRC(1,0,0). When DIV2N is divisible by eight, then
CLKSRC(1,1,0) is guaranteed to be rising edge phase-aligned
with CLKSRC(1,0,0).
PLL stability cannot be guaranteed for values below 16 and
above 1023. If values above 1023 are needed, use CyClocksRT
to determine the best charge pump setting.
Clock Output Settings: CLKSRC – Clock Output
Crosspoint Switch Matrix [44H(7..0)], [45H(7..0)],
[46H(7..6)]
Each clock output has its own output enable, controlled by
register 09H(5..0). To enable an output, set the corresponding
CLKOE bit to 1. CLKOE settings are in Table 14 on page 8.
The output swing of LCLK1 through LCLK4 is set by VDDL. The
output swing of CLK5 and CLK6 is set by VDD.
CLKOE – Clock Output Enable Control [09H(5..0)]
Every clock output can be defined to come from one of seven
unique frequency sources. The CLKSRC(2..0) crosspoint switch
matrix defines which source is attached to each individual clock
output. CLKSRC(2..0) is set in Registers 44H, 45H, and 46H.
The remainder of register 46H(5:0) must be written with the
values stated in the register table when writing register values
46H(7:6).
Test, Reserved, and Blank Registers
Writing to any of the following registers causes the part to exhibit
abnormal behavior, as follows.
[00H to 08H]
[0AH to 0BH]
[0DH to 11H]
[14H to 3FH]
[43H]
[48H to FFH]
In addition, each clock output has individual CLKOE control, set
by register 09H(5..0).
When DIV1N is divisible by four, then CLKSRC(0,1,0) is
guaranteed to be rising edge phase-aligned with
– Reserved
– Reserved
– Reserved
– Reserved
– Reserved
– Reserved.
Table 12. Clock Output Setting
CLKSRC2
CLKSRC1
CLKSRC0
Definition and Notes
0
0
0
Reference input.
0
0
1
DIV1CLK/DIV1N. DIV1N is defined by register [OCH]. Allowable values for DIV1N are 4
to 127. If Divider Bank 1 is not being used, set DIV1N to 8.
0
1
0
DIV1CLK/2. Fixed /2 divider option. If this option is used, DIV1N must be divisible by 4.
0
1
1
DIV1CLK/3. Fixed /3 divider option. If this option is used, set DIV1N to 6.
1
0
0
DIV2CLK/DIV2N. DIV2N is defined by Register [47H]. Allowable values for DIV2N are 4
to 127. If Divider Bank 2 is not being used, set DIV2N to 8.
1
0
1
DIV2CLK/2. Fixed /2 divider option. If this option is used, DIV2N must be divisible by 4.
1
1
0
DIV2CLK/4. Fixed /4 divider option. If this option is used, DIV2N must be divisible by 8.
1
1
1
Reserved – do not use.
Table 13. Clock Output Register Setting
Address
D7
D6
D5
D4
D3
D2
D1
D0
44H
CLKSRC2 for CLKSRC1 for CLKSRC0 for CLKSRC2 for CLKSRC1 for CLKSRC0 for CLKSRC2 for CLKSRC1 for
LCLK1
LCLK1
LCLK1
LCLK2
LCLK2
LCLK2
LCLK3
LCLK3
45H
CLKSRC0 for CLKSRC2 for CLKSRC1 for CLKSRC0 for CLKSRC2 for CLKSRC1 for CLKSRC0 for CLKSRC2 for
LCLK3
LCLK4
LCLK4
LCLK4
CLK5
CLK5
CLK5
CLK6
46H
CLKSRC1 for CLKSRC0 for
CLK6
CLK6
Document #: 38-07104 Rev. *I
1
1
1
1
1
1
Page 7 of 16
[+] Feedback
CY22150
Table 14. CLKOE Bit Setting
Address
D7
D6
D5
D4
D3
D2
D1
D0
09H
0
0
CLK6
CLK5
LCLK4
LCLK3
LCLK2
LCLK1
Programmable Interface Timing
The CY22150 uses a two-wire serial-interface SDAT and SCLK
that operates up to 400 kbits/second in Read or Write mode. The
basic Write serial format is as follows.
Start Sequence – Start frame is indicated by SDAT going LOW
when SCLK is HIGH. Every time a Start signal is given, the next
eight-bit data must be the device address (seven bits) and a R/W
bit, followed by register address (eight bits) and register data
(eight bits).
Start Bit; seven-bit Device Address (DA); R/W Bit; Slave Clock
Acknowledge (ACK); eight-bit Memory Address (MA); ACK;
eight-bit data; ACK; eight-bit data in MA + 1 if desired; ACK;
eight-bit data in MA+2; ACK; and so on until STOP bit.The basic
serial format is illustrated in Figure 4 on page 8.
Stop Sequence – Stop frame is indicated by SDAT going HIGH
when SCLK is HIGH. A Stop frame frees the bus for writing to
another part on the same bus or writing to another random
register address.
Data Valid
During Write mode, the CY22150 responds with an ACK pulse
after every eight bits. This is accomplished by pulling the SDAT
line LOW during the N*9th clock cycle, as illustrated in Figure 6
on page 9. (N = the number of eight-bit segments transmitted.)
During Read mode, the ACK pulse after the data packet is sent
is generated by the master
Data is valid when the Clock is HIGH, and may only be transitioned when the clock is LOW, as illustrated in Figure 3.
Data Frame
Every new data frame is indicated by a start and stop sequence,
as illustrated in Figure 5 on page 9.
Acknowledge Pulse
.
Figure 3. Data Valid and Data Transition Periods
Data valid
Transition to next bit
SDAT
CLKHIGH
tDH
tSU
VIH
SCLK
VIL
CLKLOW
Figure 4. Data Frame Architecture
SDAT Write
Multiple
Contiguous
Registers
1-bit
1-bit
1-bit 1-bit
1-bit Slave Slave
Slave
Slave
ACK
ACK
R/W = 0 ACK ACK
7-bit
8-bit
8-bit
8-bit
8-bit
Device Register Register Register Register
Data
Address Address Data
Data
(XXH) (XXH) (XXH+1) (XXH+2)
1-bit
Slave
ACK
1-bit
Slave
ACK
8-bit
Register
Data
(FFH)
1-bit
Slave
ACK
8-bit
Register
Data
(00H)
Stop Signal
Start Signal
SDAT Read
Multiple
Contiguous
Registers
1-bit
Slave
ACK
1-bit
1-bit 1-bit
1-bit Slave Slave
1-bit
Master
R/W = 1 ACK
R/W = 0 ACK ACK
7-bit
8-bit
8-bit
8-bit
Device Register 7-Bit
Register Register
Address Address Device Data
Data
(XXH) Address (XXH)
(XXH+1)
Start Signal
Document #: 38-07104 Rev. *I
1-bit
Master
ACK
1-bit
Master
ACK
8-bit
Register
Data
(FFH)
1-bit
Master
ACK
1-bit
Master
ACK
8-bit
Register
Data
(00H)
Stop Signal
Page 8 of 16
[+] Feedback
CY22150
Figure 5. Start and Stop Frame
SDAT
Transition
to next bit
START
SCLK
STOP
Figure 6. Frame Format (Device Address, R/W, Register Address, Register Data
SDAT
+
START DA6
SCLK
DA5DA0
+
R/W ACK
RA6RA1
RA0
ACK
D7
+
+
Parameter
fSCLK
RA7
+
Description
D6
D1
D0
ACK
STOP
+
Min
Frequency of SCLK
Max
Unit
400
kHz
Start mode time from SDA LOW to SCL LOW
0.6
μs
CLKLOW
SCLK LOW period
1.3
μs
CLKHIGH
SCLK HIGH period
0.6
μs
tSU
Data transition to SCLK HIGH
100
ns
tDH
Data hold (SCLK LOW to data transition)
0
ns
Rise time of SCLK and SDAT
300
ns
Fall time of SCLK and SDAT
300
ns
Stop mode time from SCLK HIGH to SDAT HIGH
0.6
μs
Stop mode to Start mode
1.3
μs
Document #: 38-07104 Rev. *I
Page 9 of 16
[+] Feedback
CY22150
Applications
Controlling Jitter
Jitter is defined in many ways including: phase noise, long term
jitter, cycle to cycle jitter, period jitter, absolute jitter, and deterministic. These jitter terms are usually given in terms of rms,
peak to peak, or in the case of phase noise dBC/Hz with respect
to the fundamental frequency.
Power supply noise and clock output loading are two major
system sources of clock jitter. Power supply noise is mitigated by
proper power supply decoupling (0.1 μF ceramic cap 0.25”) of
the clock and ensuring a low impedance ground to the chip.
Reducing capacitive clock output loading to a minimum lowers
current spikes on the clock edges and thus reduces jitter.
Reducing the total number of active outputs also reduce jitter in
a linear fashion. However, it is better to use two outputs to drive
two loads than one output to drive two loads.
The rate and magnitude that the PLL corrects the VCO frequency
is directly related to jitter performance. If the rate is too slow, then
long term jitter and phase noise is poor. Therefore, to improve
long term jitter and phase noise, reducing Q to a minimum is
advisable. This technique increases the speed of the Phase
Frequency Detector which in turn drive the input voltage of the
VCO. In a similar manner increasing P till the VCO is near its
maximum rated speed also decreases long term jitter and phase
noise. For example: Input Reference of 12 MHz; desired output
frequency of 33.3 MHz. The following solution is possible: Set
Q = 3, P = 25, Post Div = 3. However, the best jitter results is
Q = 2, P = 50, Post Div = 9.
For more information, contact your local Cypress field applications engineer.
Figure 7. Test Circuit
VDD
CLK out
0.1 mF
C LOAD
OUTPUTS
AVDD
VDDL
0.1 μF
0.1 mF
GND
Figure 8. Duty Cycle Definition; DC = t2/t1
Figure 9. Rise and Fall Time Definitions
t1
t3
t4
t2
80%
CLK
CLK
50%
50%
20%
Figure 10. Peak-to-Peak Jitter
t6
Document #: 38-07104 Rev. *I
Page 10 of 16
[+] Feedback
CY22150
Absolute Maximum Conditions
Parameter
Min
Max
Unit
VDD
Supply Voltage
Description
–0.5
7.0
V
VDDL
I/O Supply Voltage
–0.5
7.0
V
TS
Storage Temperature[2]
–65
125
°C
TJ
Junction Temperature
125
°C
Package Power Dissipation – Commercial Temp
450
mW
380
mW
AVDD + 0.3
V
Package Power Dissipation – Industrial Temp
Digital Inputs
ESD
AVSS – 0.3
Digital Outputs Referred to VDD
VSS – 0.3
VDD + 0.3
V
Digital Outputs Referred to VDDL
VSS – 0.3
VDDL +0.3
V
2000
V
Static Discharge Voltage per MIL-STD-833, Method 3015
Recommended Operating Conditions
Parameter
Description
Min
Typ.
Max
Unit
VDD
Operating Voltage
3.135
3.3
3.465
V
VDDLHI[3]
Operating Voltage
3.135
3.3
3.465
V
VDDLLO[3]
Operating Voltage
2.375
2.5
TAC
Ambient Commercial Temp
TAI
Ambient Industrial Temp
CLOAD
Max. Load Capacitance, VDD/VDDL = 3.3V
CLOAD
Max. Load Capacitance, VDDL = 2.5V
fREFD
Driven REF
fREFC
Crystal REF
tPU
2.625
V
0
70
°C
–40
85
°C
15
pF
15
pF
133
MHz
8
30
MHz
0.05
500
ms
1
Power up time for all VDDs to reach minimum
specified voltage (power ramps must be monotonic)
DC Electrical Characteristics
Parameter[4]
Min
Typ.
IOH3.3
Output High Current
Name
VOH = VDD – 0.5, VDD/VDDL = 3.3V (sink)
Description
12
24
Max
Unit
mA
IOL3.3
Output Low Current
VOL = 0.5, VDD/VDDL = 3.3V (source)
12
24
mA
IOH2.5
Output High Current
VOH = VDDL – 0.5, VDDL = 2.5V (source)
8
16
mA
IOL2.5
Output Low Current
VOL = 0.5, VDDL = 2.5V (sink)
8
16
VIH
Input High Voltage
CMOS levels, 70% of VDD
VIL
Input Low Voltage
CMOS levels, 30% of VDD
CIN
Input Capacitance
SCLK and SDAT Pins
IIZ
Input Leakage Current
SCLK and SDAT Pins
VHYS
Hysteresis of Schmitt
triggered inputs
SCLK and SDAT Pins
IVDD[5,6]
mA
0.7
VDD
0.3
VDD
7
pF
μA
5
0.05
VDD
Supply Current
AVDD/VDD Current
[5,6]
Supply Current
VDDL Current (VDDL = 3.465V)
25
mA
IVDDL2.5[5,6]
Supply Current
VDDL Current (VDDL = 2.625V)
17
mA
IVDDL3.3
45
mA
Notes
2. Rated for 10 years.
3. VDDLis only specified and characterized at 3.3V ± 5% and 2.5V ± 5%. VDDLmay be powered at any value between 3.465V and 2.375V.
4. Not 100% tested.
5. IVDD currents specified for two CLK outputs running at 125 MHz, two LCLK outputs running at 80 MHz, and two LCLK outputs running at 66.6 MHz.
6. Use CyClocksRT to calculate actual IVDD and IVDDL for specific output frequency configurations.
Document #: 38-07104 Rev. *I
Page 11 of 16
[+] Feedback
CY22150
AC Electrical Characteristics
Parameter[7]
t1
Name
Output Frequency,
Commercial Temp
Output Frequency,
Industrial Temp
t2LO
Output Duty Cycle
t2HI
Output Duty Cycle
t3LO
Rising Edge Slew
Rate (VDDL = 2.5V)
Falling Edge Slew
Rate (VDDL = 2.5V)
Rising Edge Slew
Rate (VDDL = 3.3V)
Falling Edge Slew
Rate (VDDL = 3.3V)
Skew
Clock Jitter
PLL Lock Time
t4LO
t3HI
t4HI
t5[8]
t6[9]
t10
Description
Clock output limit, 3.3V
Clock output limit, 2.5V
Clock output limit, 3.3V
Clock output limit, 2.5V
Duty cycle is defined in Figure 8 on page 10;
t1/t2
fOUT < 166 MHz, 50% of VDD
Duty cycle is defined in Figure 8; t1/t2
fOUT > 166 MHz, 50% of VDD
Output clock rise time, 20% to 80% of VDDL.
Defined in Figure 9
Output dlock fall time, 80% to 20% of VDDL.
Defined in Figure 9
Output dlock rise time, 20% to 80% of
VDD/VDDL. Defined in Figure 9
Output dlock fall time, 80% to 20% of VDD/VDDL.
Defined in Figure 9
Output-output skew between related outputs
Peak-to-peak period jitter
Min
0.08 (80 kHz)
0.08 (80 kHz)
0.08 (80 kHz)
0.08 (80 kHz)
45
Typ.
50
Max
200
166.6
166.6
150
55
Unit
MHz
MHz
MHz
MHz
%
40
50
60
%
0.6
1.2
V/ns
0.6
1.2
V/ns
0.8
1.4
V/ns
0.8
1.4
V/ns
250
250
0.30
3
ps
ps
ms
Device Characteristics
Parameter
θJA
Complexity
Document #: 38-07104 Rev. *I
Name
Theta JA
Transistor Count
Value
115
74,600
Unit
°C/W
Transistors
Page 12 of 16
[+] Feedback
CY22150
Ordering Information
Ordering Code
CY22150FC[11]
CY22150FCT[11]
CY22150FI[11]
CY22150ZI-xxxT[10, 11]
CY22150KFC
CY22150KFCT
CY22150KFI
CY22150KZI-xxx[10]
CY22150KZI-xxxT[10]
Pb-Free
CY22150FZXC[11]
CY22150FZXCT[11]
CY22150FZXI[11]
CY22150FZXIT[11]
CY22150ZXC-xxx[10, 11]
CY22150ZXC-xxxT[10, 11]
CY22150ZXI-xxx[10, 11]
CY22150ZXI-xxxT[10, 11]
CY22150KFZXC
CY22150KFZXCT
CY22150KFZXI
CY22150KFZXIT
CY22150KZXI-xxxT[10]
Programmer
CY3672-USB
CY3672ADP000
Package Type
16-Pin TSSOP
16-Pin TSSOP - Tape and Reel
16-Pin TSSOP
16-Pin TSSOP- Tape and Reel
16-Pin TSSOP
16-Pin TSSOP - Tape and Reel
16-Pin TSSOP
16-Pin TSSOP
16-Pin TSSOP- Tape and Reel
Operating Range
Commercial (0 to 70°C)
Commercial (0 to 70°C)
Industrial (–40 to 85°C)
Industrial (–40 to 85°C)
Commercial (0 to 70°C)
Commercial (0 to 70°C)
Industrial (–40 to 85°C)
Industrial (–40 to 85°C)
Industrial (–40 to 85°C)
16-Pin TSSOP
16-Pin TSSOP - Tape and Reel
16-Pin TSSOP
16-Pin TSSOP - Tape and Reel
16-Pin TSSOP
16-Pin TSSOP- Tape and Reel
16-Pin TSSOP
16-Pin TSSOP- Tape and Reel
16-Pin TSSOP
16-Pin TSSOP - Tape and Reel
16-Pin TSSOP
16-Pin TSSOP - Tape and Reel
16-Pin TSSOP- Tape and Reel
Commercial (0 to 70°C)
Commercial (0 to 70°C)
Industrial (–40 to 85°C)
Industrial (–40 to 85°C)
Commercial (0 to 70°C)
Commercial (0 to 70°C)
Industrial (–40 to 85°C)
Industrial (–40 to 85°C)
Commercial (0 to 70°C)
Commercial (0 to 70°C)
Industrial (–40 to 85°C)
Industrial (–40 to 85°C)
Industrial (–40 to 85°C)
Operating Voltage
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
FTG Programmer with USB interface
CY22150 Socket for CY3672-USB
Notes
7. Not 100% tested, guaranteed by design.
8. Skew value guaranteed when outputs are generated from the same divider bank. See Logic Block Diagram on page 1 for more information.
9. Jitter measurements vary. Actual jitter is dependent on XIN jitter and edge rate, number of active outputs, output frequencies, VDDL, (2.5V or 3.3V jitter)
10. The CY22150ZC-xxx and CY22150ZI-xxx are factory programmed configurations. Factory programming is available for high volume design opportunities of
100 Ku/year or more in production. For more details, contact your local Cypress FAE or Cypress Sales Representative.
11. Not recommended for new designs.
Document #: 38-07104 Rev. *I
Page 13 of 16
[+] Feedback
CY22150
Package Diagram
Figure 11. 16-Pin TSSPO 4.40 mm Body Z16.173
PIN 1 ID
DIMENSIONS IN MM[INCHES] MIN.
MAX.
1
REFERENCE JEDEC MO-153
6.25[0.246]
6.50[0.256]
PACKAGE WEIGHT 0.05 gms
PART #
4.30[0.169]
4.50[0.177]
Z16.173
STANDARD PKG.
ZZ16.173 LEAD FREE PKG.
16
0.65[0.025]
BSC.
0.19[0.007]
0.30[0.012]
1.10[0.043] MAX.
0.25[0.010]
BSC
GAUGE
PLANE
0°-8°
0.076[0.003]
0.85[0.033]
0.95[0.037]
4.90[0.193]
5.10[0.200]
0.05[0.002]
0.15[0.006]
SEATING
PLANE
0.50[0.020]
0.70[0.027]
0.09[[0.003]
0.20[0.008]
51-85091 *A
Document #: 38-07104 Rev. *I
Page 14 of 16
[+] Feedback
CY22150
Document History Page
Document Title: CY22150 One-PLL General-Purpose Flash-Programmable and 2-Wire Serially-Programmable Clock Generator
Document Number: 38-07104
REV.
ECN
NO.
Issue
Date
Orig. of
Change
**
107498
08/08/01
CKN
New Data Sheet
*A
110043
02/06/02
CKN
Preliminary to Final
*B
113514
05/01/02
CKN
Removed overline on Figure 6 Register Address Register Data
Changed CLKHIGH unit from ns to μs in parameter description table
Added (sink) to rows 1 and 4 and added (source) to rows 2 and 3 in the DC
Electrical Characteristics table (Figure )
*C
121868
12/14/02
RBI
Power up requirements added to Operating Conditions Information
*D
125453
05/19/03
CKN
Changed 0 to 1 under 12H/D5 of Table 2 and Table 4.
Reworded and reformatted Programmable Crystal Input Oscillator Gain
Settings text.
*E
242808
See ECN
RGL
Minor Change: Fixed the broken line in the block diagram
Description of Change
*F
252352
See ECN
RGL
Corrected Table 2 specs.
*G
296084
See ECN
RGL
Added Pb-Free Devices
*H
2440846
See ECN
AESA
*I
2649578
01/29/09
Document #: 38-07104 Rev. *I
Updated template. Added Note “Not recommended for new designs.”
Added part number CY22150KFC, CY22150KFCT, CY22150KFI,
CY22150KFZXC, CY22150KFZXCT, CY22150KFZXI, CY22150KFZXIT,
CY22150KZXI-xxxT, and CY22150KZI-xxxT in ordering information table.
Replaced Lead Free with Pb-Free.
KVM/PYRS Removed reference to note “Not recommended for new designs” for the
following parts: CY22150KFC, CY22150KFCT, CY22150KFI
Added CY22150KZI-xxx to the Ordering Information Table
Removed CY22150ZC-xxx, CY22150ZC-xxxT and CY22150ZI-xxx from the
Ordering Information Table
Changed CY3672 to CY3672-USB, and moved to the bottom of the table
Page 15 of 16
[+] Feedback
CY22150
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at cypress.com/sales.
Products
PSoC
Clocks & Buffers
Wireless
Memories
Image Sensors
PSoC Solutions
psoc.cypress.com
clocks.cypress.com
General
Low Power/Low Voltage
psoc.cypress.com/solutions
psoc.cypress.com/low-power
wireless.cypress.com
Precision Analog
memory.cypress.com
LCD Drive
psoc.cypress.com/lcd-drive
CAN 2.0b
psoc.cypress.com/can
USB
psoc.cypress.com/usb
image.cypress.com
psoc.cypress.com/precision-analog
© Cypress Semiconductor Corporation, 2001-2009. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document #: 38-07104 Rev. *I
Revised January 23, 2009
Page 16 of 16
BP Microsystems is a trademark of BP Microsystems. HiLo Systems is a trademark of Hi-Lo Systems, Inc. CyClocks is a trademark of Cypress Semiconductor. All product and company names
mentioned in this document are the trademarks of their respective holders.
[+] Feedback