CY62137VN MoBL® 2-Mbit (128K x 16) Static RAM Features • Temperature Ranges — Industrial: –40°C to 85°C — Automotive-A: –40°C to 85°C — Automotive-E: –40°C to 125°C • High Speed: 55 ns • Wide voltage range: 2.7V–3.6V • Ultra-low active, standby power • Easy memory expansion with CE and OE features • TTL-compatible inputs and outputs • Automatic power-down when deselected • CMOS for optimum speed/power • Available in Pb-free 44-pin TSOP Type II package Functional Description[1] The CY62137VN is a high-performance CMOS static RAM organized as 128K words by 16 bits. This device features advanced circuit design to provide ultra-low active current. This is ideal for providing More Battery Life™ (MoBL®) in portable applications such as cellular telephones. The device also has an automatic power-down feature that reduces power consumption by 99% when addresses are not toggling. The device can also be put into standby mode when deselected (CE HIGH) or when CE is LOW and both BLE and BHE are HIGH. The input/output pins (I/O0 through I/O15) are placed in a high-impedance state when: deselected (CE HIGH), outputs are disabled (OE HIGH), BHE and BLE are disabled (BHE, BLE HIGH), or during a write operation (CE LOW, and WE LOW).Writing to the device is accomplished by taking Chip Enable (CE) and Write Enable (WE) inputs LOW. If Byte Low Enable (BLE) is LOW, then data from I/O pins (I/O0 through I/O7), is written into the location specified on the address pins (A0 through A16). If Byte High Enable (BHE) is LOW, then data from I/O pins (I/O8 through I/O15) is written into the location specified on the address pins (A0 through A16).Reading from the device is accomplished by taking Chip Enable (CE) and Output Enable (OE) LOW while forcing the Write Enable (WE) HIGH. If Byte Low Enable (BLE) is LOW, then data from the memory location specified by the address pins will appear on I/O0 to I/O7. If Byte High Enable (BHE) is LOW, then data from memory will appear on I/O8 to I/O15. See the truth table at the back of this data sheet for a complete description of read and write modes. Logic Block Diagram DATA IN DRIVERS A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 SENSE AMPS ROW DECODER 10 128K x 16 RAM Array I/O0–I/O7 I/O8–I/O15 BHE WE CE OE BLE A12 A13 A14 A15 A16 A11 COLUMN DECODER CE Power-down Circuit BHE BLE Note: 1. For best practice recommendations, please refer to the Cypress application note “System Design Guidelines” on http://www.cypress.com. Cypress Semiconductor Corporation Document #: 001-06497 Rev. *A • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised August 3, 2006 [+] Feedback CY62137VN MoBL® Product Portfolio Power Dissipation Speed (ns) VCC Range (V) Product CY62137VNLL Industrial Min. Typ.[3] Max. 2.7 3.0 3.6 55 Operating, ICC (mA) Standby, ISB2 (µA) Typ.[3] Max. Typ.[3] Max. 7 20 1 15 CY62137VNLL 70 7 15 1 15 CY62137VNLL Automotive-A 70 7 15 1 15 CY62137VNLL Automotive-E 70 7 15 1 20 Pin Configurations TSOP II (Forward) Top View A4 A3 A2 A1 A0 CE I/O0 I/O1 I/O2 I/O3 VCC VSS I/O4 I/O5 I/O6 I/O7 WE A16 A15 A14 A13 A12 1 44 2 3 43 42 4 41 40 39 38 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 A5 A6 A7 OE BHE BLE I/O15 I/O14 I/O13 I/O12 VSS VCC I/O11 I/O10 I/O9 I/O8 NC A8 A9 A10 A11 NC Pin Definitions Pin Number Type Description 1–5, 18–22, 24–27, 42–45 Input A0–A16. Address Inputs 7–10, 13–16, 29–32, 35–38 Input/Output I/O0–I/O15. Data lines. Used as input or output lines depending on operation 23 No Connect NC. This pin is not connected to the die 17 Input/Control WE. When selected LOW, a WRITE is conducted. When selected HIGH, a READ is conducted 6 Input/Control CE. When LOW, selects the chip. When HIGH, deselects the chip 40, 39 Input/Control Byte Write Select Inputs, active LOW. BHE controls I/O15–I/O8, BLE controls I/O7–I/O0. 41 Input/Control OE. Output Enable. Controls the direction of the I/O pins. When LOW, the I/O pins behave as outputs. When deasserted HIGH, I/O pins are tri-stated, and act as input data pins 12, 34 Ground 11, 33 Power Supply VCC. Power supply for the device VSS. Ground for the device Notes: 2. NC pins are not connected on the die. 3. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC = VCC(TYP)., TA = 25°C. Document #: 001-06497 Rev. *A Page 2 of 11 [+] Feedback CY62137VN MoBL® Maximum Ratings Output Current into Outputs (LOW)............................. 20 mA (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ................................. –65°C to +150°C Ambient Temperature with Power Applied............................................. –55°C to +125°C Static Discharge Voltage........................................... > 2001V (per MIL-STD-883, Method 3015) Latch-up Current..................................................... > 200 mA Operating Range Supply Voltage to Ground Potential ............... –0.5V to +4.6V Range Ambient Temperature VCC DC Voltage Applied to Outputs in High-Z State[4] ....................................–0.5V to VCC + 0.5V Industrial –40°C to +85°C 2.7V to 3.6V DC Input Voltage[4] .................................–0.5V to VCC + 0.5V Automotive-A –40°C to +85°C Automotive-E –40°C to +125°C Electrical Characteristics Over the Operating Range -55 Parameter -70 Test Conditions Min. 2.4 VOL Output HIGH Voltage VCC = 2.7V, IOH = –1.0 mA Output LOW Voltage VCC = 2.7V, IOL = 2.1 mA VIH Input HIGH Voltage 2.2 VCC + 0.5V VIL Input LOW Voltage –0.5 IIX Input Leakage Current GND < VI < VCC IOZ Output Leakage Current GND < VO < VCC, Output Disabled ICC VCC Operating Supply Current IOUT = 0 mA, VCC = 3.6V Ind’l f = fMAX = 1/tRC, Auto-A/ CMOS Levels Auto-E 7 IOUT = 0 mA, f = 1 MHz, CMOS Levels 1 VOH ISB1 ISB2 Description Typ.[3] Max. Min. Typ.[3] Max. 2.4 V 0.4 0.4 V 2.2 VCC + 0.5V V 0.8 –0.5 0.8 V –1 +1 –1 +1 µA –1 +1 –1 +1 µA 7 15 mA 7 15 1 2 1 2 Ind’l 20 2 Auto-A/ Auto-E Automatic CE Power-down Current—CMOS Inputs CE > VCC – 0.3V, VCC = 3.6V Ind’l VIN > VCC – 0.3V Auto-A/ or VIN < 0.3V, Auto-E f = fMAX Automatic CE Power-down Current—CMOS Inputs CE > VCC – 0.3V VCC = 3.6V Ind’l/ VIN > VCC – 0.3V Auto-A or VIN < 0.3V, f=0 Auto-E Unit 100 mA µA 100 100 1 15 1 15 1 15 1 20 µA Capacitance[5] Parameter Description CIN Input Capacitance COUT Output Capacitance Test Conditions TA = 25°C, f = 1 MHz, VCC = VCC(typ) Max. Unit 6 pF 8 pF Thermal Resistance[5] Parameter ΘJA ΘJC Description Test Conditions Thermal Resistance (Junction to Ambient) Still Air, soldered on a 4.25 x 1.125 inch, Thermal Resistance (Junction to Case) 2-layer printed circuit board TSOPII Unit 60 °C/W 22 °C/W Notes: 4. VIL(min.) = –2.0V for pulse durations less than 20 ns. 5. Tested initially and after any design or process changes that may affect these parameters. Document #: 001-06497 Rev. *A Page 3 of 11 [+] Feedback CY62137VN MoBL® AC Test Loads and Waveforms R1 R1 VCC ALL INPUT PULSES VCC OUTPUT VCC Typ OUTPUT INCLUDING JIG AND SCOPE (a) R2 5 pF R2 30 pF 90% 10% 90% 10% GND INCLUDING JIG AND SCOPE Fall Time: 1 V/ns Rise Time: 1 V/ns (b) (c) Equivalent to: THÉVENIN EQUIVALENT RTH OUTPUT Parameters VTH Value Unit R1 1105 Ohms R2 1550 Ohms RTH 645 Ohms VTH 1.75 Volts Data Retention Characteristics (Over the Operating Range) Parameter Description VDR VCC for Data Retention ICCDR Data Retention Current tCDR[5] Chip Deselect to Data Retention Time tR Operation Recovery Time Conditions Typ.[3] Min. Max. 1.0 VCC = 1.0V, CE > VCC – 0.3V, VIN > VCC – 0.3V or VIN < 0.3V; No input may exceed VCC + 0.3V Unit V Ind’l/Auto-A 0.5 Auto-E 7.5 µA 10 0 ns tRC ns Data Retention Waveform DATA RETENTION MODE VCC VCC(min.) tCDR VDR > 1.0 V VCC(min.) tR CE Document #: 001-06497 Rev. *A Page 4 of 11 [+] Feedback CY62137VN MoBL® Switching Characteristics Over the Operating Range [6] 55 ns Parameter Description Min. 70 ns Max. Min. Max. Unit Read Cycle tRC Read Cycle Time 55 tAA Address to Data Valid tOHA Data Hold from Address Change tACE CE LOW to Data Valid 55 70 ns tDOE OE LOW to Data Valid 25 35 ns [7] tLZOE OE LOW to Low-Z 55 10 OE HIGH to High-Z ns 70 10 5 [7, 8] tHZOE 70 ns 5 25 ns ns 25 ns CE LOW to Low-Z[7] tHZCE CE HIGH to High-Z[7, 8] tPU CE LOW to Power-up tPD CE HIGH to Power-down 55 70 ns BHE / BLE LOW to Data Valid 55 70 ns tLZCE tDBE tLZBE (9) tHZBE Write BHE / BLE LOW to Low-Z 10 10 25 0 25 0 5 BHE / BLE HIGH to High-Z ns ns 5 25 ns ns 25 ns Cycle[10, 11] tWC Write Cycle Time 55 70 ns tSCE CE LOW to Write End 45 60 ns tAW Address Set-up to Write End 45 60 ns tHA Address Hold from Write End 0 0 ns tSA Address Set-up to Write Start 0 0 ns tPWE WE Pulse Width 40 50 ns tSD Data Set-up to Write End 25 30 ns tHD Data Hold from Write End 0 0 ns tHZWE WE LOW to High-Z[7, 8] [7] tLZWE WE HIGH to Low-Z tBW BHE / BLE LOW to End of Write 20 25 ns 5 10 ns 50 60 ns Notes: 6. Test conditions assume signal transition time of 5 ns or less, timing reference levels of 1.5V, input levels of 0 to VCC typ., and output loading of the specified IOL/IOH and 30 pF load capacitance. 7. At any given temperature and voltage condition, tHZCE is less than tLZCE, tHZOE is less than tLZOE, and tHZWE is less than tLZWE for any given device. 8. tHZOE, tHZCE, and tHZWE are specified with CL = 5 pF as in (b) of AC Test Loads. Transition is measured ±500 mV from steady-state voltage. 9. If both byte enables are toggled together this value is 10 ns. 10. The internal write time of the memory is defined by the overlap of CE LOW and WE LOW. Both signals must be LOW to initiate a write and either signal can terminate a write by going HIGH. The data input set-up and hold timing should be referenced to the rising edge of the signal that terminates the write. 11. The minimum write cycle time for write cycle #3 (WE controlled, OE LOW) is the sum of tHZWE and tSD. Document #: 001-06497 Rev. *A Page 5 of 11 [+] Feedback CY62137VN MoBL® Switching Waveforms Read Cycle No. 1[12, 13] tRC ADDRESS tOHA DATA OUT tAA PREVIOUS DATA VALID DATA VALID Read Cycle No. 2[13, 14] tRC CE tPD tHZCE tACE OE tHZOE tDOE BHE/BLE tLZOE tHZBE tDBE tLZBE DATA OUT HIGH IMPEDANCE HIGH IMPEDANCE DATA VALID tLZCE VCC SUPPLY CURRENT tPU ICC 50% 50% ISB Notes: 12. Device is continuously selected. OE, CE = VIL. 13. WE is HIGH for read cycle. 14. Address valid prior to or coincident with CE transition LOW. Document #: 001-06497 Rev. *A Page 6 of 11 [+] Feedback CY62137VN MoBL® Switching Waveforms (continued) Write Cycle No. 1 (WE Controlled)[10, 15, 16] tWC ADDRESS CE tAW tHA tSA WE tPWE tBW BHE/BLE OE tSD DATA I/O tHD DATAIN VALID NOTE 17 tHZOE Write Cycle No. 2 (CE Controlled)[10, 15, 16] tWC ADDRESS tSCE CE tSA tAW BHE/BLE WE tHA tBW tPWE tSD DATA I/O tHD DATAIN VALID Notes: 15. Data I/O is high-impedance if OE = VIH. 16. If CE goes HIGH simultaneously with WE HIGH, the output remains in a high-impedance state. 17. During this period, the I/Os are in output state and input signals should not be applied. Document #: 001-06497 Rev. *A Page 7 of 11 [+] Feedback CY62137VN MoBL® Switching Waveforms (continued) Write Cycle No. 3 (WE Controlled, OE LOW)[11, 16] tWC ADDRESS CE tAW tBW BHE/BLE WE tHA tSA tSD DATA I/O tHD DATAIN VALID NOTE 17 tLZWE tHZWE Write Cycle No. 4 (BHE/BLE Controlled, OE LOW)[17] tWC ADDRESS CE tAW tHA tBW BHE/BLE tSA WE tSD DATA I/O DATAIN VALID NOTE 17 tHZWE Document #: 001-06497 Rev. *A tHD tLZWE Page 8 of 11 [+] Feedback CY62137VN MoBL® Typical DC and AC Characteristics Normalized Operating Current vs. Supply Voltage 1.4 Standby Current vs. Supply Voltage 35 MoBL 30 1.2 MoBL 25 ISB (µA) 1.0 ICC 0.8 0.6 20 15 10 0.4 5 0.2 0.0 1.7 0 2.2 2.7 3.2 SUPPLY VOLTAGE (V) 1.0 3.7 2.7 2.8 3.7 1.9 SUPPLY VOLTAGE (V) Access Time vs. Supply Voltage 80 MoBL 70 60 TAA (ns) 50 40 30 20 10 1.0 2.7 2.8 1.9 3.7 SUPPLY VOLTAGE (V) Truth Table CE WE OE BHE BLE H X X X X High-Z High-Z Deselect/Power-down Standby (ISB) X X X H H High-Z High-Z Deselect/Power-down Standby (ISB) L H L L L Data Out Data Out Read Active (ICC) L H L H L High-Z Data Out Read Active (ICC) L H L L H Data Out High-Z Read Active (ICC) L H H X X High-Z High-Z Output Disabled Active (ICC) L L X L L Data In Data In Write Active (ICC) L L X H L High-Z Data In Write Active (ICC) L L X L H Data In High-Z Write Active (ICC) Document #: 001-06497 Rev. *A I/O8–I/O15 I/O0–I/O7 Mode Power Page 9 of 11 [+] Feedback CY62137VN MoBL® Ordering Information Speed (ns) Ordering Code Package Diagram Operating Range Package Type 55 CY62137VNLL-55ZXI 51-85087 44-pin TSOP II (Pb-free) Industrial 70 CY62137VNLL-70ZXI 44-pin TSOP II (Pb-free) Industrial CY62137VNLL-70ZSXA 44-pin TSOP II (Pb-free) Automotive-A CY62137VNLL-70ZSXE 44-pin TSOP II (Pb-free) Automotive-E Please contact your local Cypress sales representative for availability of these parts Package Diagram 44-Pin TSOP II (51-85087) DIMENSION IN MM (INCH) MAX MIN. PIN 1 I.D. 1 23 10.262 (0.404) 10.058 (0.396) 11.938 (0.470) 11.735 (0.462) 22 EJECTOR PIN 44 TOP VIEW 0.800 BSC (0.0315) OR E K X A SG BOTTOM VIEW 0.400(0.016) 0.300 (0.012) 10.262 (0.404) 10.058 (0.396) BASE PLANE 0.210 (0.0083) 0.120 (0.0047) 0°-5° 0.10 (.004) 0.150 (0.0059) 0.050 (0.0020) 1.194 (0.047) 0.991 (0.039) 18.517 (0.729) 18.313 (0.721) SEATING PLANE 0.597 (0.0235) 0.406 (0.0160) 51-85087-*A MoBL is a registered trademark, and More Battery Life is a trademark, of Cypress Semiconductor Corporation. All product and company names mentioned in this document are the trademarks of their respective holders. Document #: 001-06497 Rev. *A Page 10 of 11 © Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. [+] Feedback CY62137VN MoBL® Document History Page Document Title: CY62137VN MoBL® 2-Mbit (128K x 16) Static RAM Document Number: 001-06497 REV. ECN NO. Issue Date Orig. of Change Description of Change ** 426503 See ECN NXR New Data Sheet *A 488954 See ECN NXR Added Automotive product Updated Ordering Information table Document #: 001-06497 Rev. *A Page 11 of 11 [+] Feedback