CYPRESS CY62146DV30LL

CY62146DV30
4-Mbit (256K x 16) Static RAM
Features
an automatic power-down feature that significantly reduces
power consumption. The device can also be put into standby
mode reducing power consumption by more than 99% when
deselected (CE HIGH). The input/output pins (I/O0 through
I/O15) are placed in a high-impedance state when: deselected
(CE HIGH), outputs are disabled (OE HIGH), both Byte High
Enable and Byte Low Enable are disabled (BHE, BLE HIGH),
or during a write operation (CE LOW and WE LOW).
• Very high speed: 45 ns
• Wide voltage range: 2.20V–3.60V
• Pin-compatible with CY62146CV30
• Ultra-low active power
— Typical active current: 1.5 mA @ f = 1 MHz
Writing to the device is accomplished by taking Chip Enable
(CE) and Write Enable (WE) inputs LOW. If Byte Low Enable
(BLE) is LOW, then data from I/O pins (I/O0 through I/O7), is
written into the location specified on the address pins (A0
through A17). If Byte High Enable (BHE) is LOW, then data
from I/O pins (I/O8 through I/O15) is written into the location
specified on the address pins (A0 through A17).
— Typical active current: 8 mA @ f = fmax
• Ultra low standby power
• Easy memory expansion with CE, and OE features
• Automatic power-down when deselected
• CMOS for optimum speed/power
Reading from the device is accomplished by taking Chip
Enable (CE) and Output Enable (OE) LOW while forcing the
Write Enable (WE) HIGH. If Byte Low Enable (BLE) is LOW,
then data from the memory location specified by the address
pins will appear on I/O0 to I/O7. If Byte High Enable (BHE) is
LOW, then data from memory will appear on I/O8 to I/O15. See
the truth table at the back of this data sheet for a complete
description of read and write modes.
• Packages offered 48-ball BGA and 44-pin TSOPII
• Also available in Lead-free packages
Functional Description[1]
The CY62146DV30 is a high-performance CMOS static RAM
organized as 256K words by 16 bits. This device features advanced circuit design to provide ultra-low active current. This
is ideal for providing More Battery Life™ (MoBL) in portable
applications such as cellular telephones. The device also has
The CY62146DV30 is available in a 48-ball VFBGA, 44-pin
TSOPII packages.
Logic Block Diagram
SENSE AMPS
ROW DECODER
DATA IN DRIVERS
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
256K x 16
RAM Array
I/O0–I/O7
I/O8–I/O15
BHE
WE
CE
OE
BLE
A17
A13
A14
A15
A16
A11
A12
COLUMN DECODER
Note:
1. For best practice recommendations, please refer to the Cypress application note “System Design Guidelines” on http://www.cypress.com.
Cypress Semiconductor Corporation
Document #: 38-05339 Rev. *A
•
3901 North First Street
•
San Jose, CA 95134
•
408-943-2600
Revised February 2, 2005
CY62146DV30
Pin Configuration[2, 3, 4]
VFBGA (Top View)
44 TSOP II (Top View)
1
2
3
4
5
6
BLE
OE
A0
A1
A2
NC
A
I/O8
BHE
A3
A4
CE
I/O0
B
I/O9
I/O10
A5
A6
I/O1
I/O2
C
VSS
I/O11
A17
A7
I/O3
Vcc
D
VCC
I/O12 DNU
A16
I/O4
Vss
E
I/O14
I/O13
A14
A15
I/O5
I/O6
F
I/O15
NC
A12
A13
WE
I/O7
G
NC
A8
A9
A10
A11
NC
A4
A3
A2
A1
A0
CE
I/O0
I/O1
I/O2
I/O3
VCC
VSS
I/O4
I/O5
I/O6
I/O7
WE
A17
A16
A15
A14
A13
H
1
44
2
3
43
42
4
41
40
39
38
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
A5
A6
A7
OE
BHE
BLE
I/O15
I/O14
I/O13
I/O12
VSS
VCC
I/O11
I/O10
I/O9
I/O8
NC
A8
A9
A10
A11
A12
Product Portfolio
Power Dissipation
Operating ICC (mA)
VCC Range (V)
Product
CY62146DV30L
f = 1MHz
f = fmax
Standby ISB2 (µA)
Min.
Typ.[5]
Max.
Speed
(ns)
Typ.[5]
Max.
Typ.[5]
Max.
Typ.[5]
Max.
2.20V
3.0
3.60
45
1.5
3
10
20
2
12
CY62146DV30LL
CY62146DV30L
8
2.20V
3.0
3.60
55
1.5
3
8
15
2
CY62146DV30LL
CY62146DV30L
12
8
2.20V
3.0
3.60
70
1.5
3
8
15
2
CY62146DV30LL
12
8
Notes:
2. NC pins are not internally connected on the die.
3. DNU pins have to be left floating or tied to VSS to ensure proper application.
4. Pins H1, G2, and H6 in the BGA package are address expansion pins for 8 Mb, 16 Mb, and 32 Mb, respectively.
5. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC = VCC(typ.), TA = 25°C.
Document #: 38-05339 Rev. *A
Page 2 of 11
CY62146DV30
DC Input Voltage[6, 7] ..................... –0.3V to VCC(MAX) + 0.3V
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ................................. –65°C to +150°C
Ambient Temperature with
Power Applied............................................. –55°C to +125°C
Output Current into Outputs (LOW)............................. 20 mA
Static Discharge Voltage........................................... >2001V
(per MIL-STD-883, Method 3015)
Latch-up Current...................................................... >200 mA
Operating Range
Supply Voltage to Ground
Potential ......................................–0.3V to + VCC(MAX) + 0.3V
Device
DC Voltage Applied to Outputs
in High-Z State[6, 7] .........................–0.3V to VCC(MAX) + 0.3V
Ambient Temperature (TA)
Range
CY62146DV30L
VCC[8]
Industrial –40°C to +85°C 2.20V to 3.60V
CY62146DV30LL
Electrical Characteristics Over the Operating Range
CY62146DV30-45
Parameter Description
VOH
VOL
VIH
VIL
Test Conditions
Output HIGH IOH = –0.1 mA VCC = 2.20V
Voltage
IOH = –1.0 mA VCC = 2.70V
Min. Typ.[5]
Input LOW
Voltage
CY62146DV30-55
Min. Typ.[5]
Max.
CY62146DV30-70
Min. Typ.[5] Max. Unit
2.0
2.0
2.0
V
2.4
2.4
2.4
V
Output LOW IOL = 0.1 mA VCC = 2.20V
Voltage
IOL = 2.1 mA VCC = 2.70V
Input HIGH
Voltage
Max.
0.4
0.4
0.4
V
0.4
0.4
0.4
V
VCC = 2.2V to 2.7V
1.8
VCC +
0.3V
1.8
VCC +
0.3V
1.8
VCC +
0.3V
V
VCC= 2.7V to 3.6V
2.2
VCC +
0.3V
2.2
VCC +
0.3V
2.2
VCC +
0.3V
V
VCC = 2.2V to 2.7V
–0.3
0.6
–0.3
0.6
–0.3
0.6
V
VCC= 2.7V to 3.6V
–0.3
0.8
–0.3
0.8
–0.3
0.8
V
IIX
Input Leakage GND < VI < VCC
Current
–1
+1
–1
+1
–1
+1
µA
IOZ
Output
Leakage
Current
GND < VO < VCC, Output
Disabled
–1
+1
–1
+1
–1
+1
µA
ICC
VCC
Operating
Supply
Current
f = fMAX =
1/tRC
Automatic
CE
Power-down
Current —
CMOS
Inputs
ISB1
ISB2
10
20
8
15
8
15
mA
1.5
3
1.5
3
1.5
3
mA
CE > VCC−0.2V,
L
VIN>VCC–0.2V, VIN<0.2V) LL
f = fMAX (Address and Data
Only),
f = 0 (OE, WE, BHE and
BLE), VCC = 3.60V
2
12
2
12
2
12
µA
CE > VCC – 0.2V,
Automatic
L
CE
VIN > VCC – 0.2V or VIN < LL
Power-down 0.2V,
Current —
f = 0, VCC = 3.60V
CMOS Inputs
2
f = 1 MHz
VCC = VCCmax
IOUT = 0 mA
CMOS levels
8
12
8
2
12
8
8
8
2
12
µA
8
Notes:
6. VIL(min.) = –2.0V for pulse durations less than 20 ns.
7. VIH(max) = VCC+0.75V for pulse durations less than 20 ns.
8. Full device AC operation assumes a 100-µs ramp time from 0 to VCC(min) and 200 µs wait time after VCC stabilization.
Document #: 38-05339 Rev. *A
Page 3 of 11
CY62146DV30
Capacitance (for all packages)[9]
Parameter
Description
CIN
Input Capacitance
COUT
Output Capacitance
Test Conditions
Max.
TA = 25°C, f = 1 MHz,
VCC = VCC(typ)
Unit
10
pF
10
pF
Thermal Resistance[9]
Parameter
Description
ΘJA
Thermal Resistance
(Junction to Ambient)
ΘJC
Thermal Resistance
(Junction to Case)
Test Conditions
BGA
TSOP II
Unit
72
75.13
°C/W
8.86
8.95
°C/W
Still Air, soldered on a 3 × 4.5 inch, four-layer
printed circuit board
AC Test Loads and Waveforms[10]
R1
VCC
OUTPUT
50 pF
ALL INPUT PULSES
90%
90%
10%
VCC
R2
10%
GND
Rise Time = 1 V/ns
INCLUDING
JIG AND
SCOPE
Fall Time = 1 V/ns
Equivalent to:
THÉVENIN EQUIVALENT
RTH
OUTPUT
V
Parameters
2.50V
3.0V
Unit
R1
16667
1103
Ω
R2
15385
1554
Ω
RTH
8000
645
Ω
VTH
1.20
1.75
V
Data Retention Characteristics (Over the Operating Range)
Parameter
Description
VDR
VCC for Data Retention
ICCDR
Data Retention Current
Typ.[5]
Max.
Unit
L
9
µA
LL
6
Conditions
Min.
1.5
VCC= 1.5V
CE > VCC – 0.2V,
VIN > VCC – 0.2V or VIN < 0.2V
tCDR[9]
Chip Deselect to Data Retention Time
tR[11]
Operation Recovery Time
V
0
ns
tRC
ns
Data Retention Waveform
VCC
VCC(min)
DATA RETENTION MODE
VDR > 1.5 V
tCDR
VCC(min)
tR
CE
Notes:
9. Tested initially and after any design or process changes that may affect these parameters.
10. Test condition for the 45 ns part is a load capacitance of 30 pF.
11. Full device operation requires linear VCC ramp from VDR to VCC(min.) > 100 µs or stable at VCC(min.) > 100 µs.
Document #: 38-05339 Rev. *A
Page 4 of 11
CY62146DV30
Switching Characteristics Over the Operating Range [12]
45 ns[10]
Parameter
Description
Min.
Max.
55 ns
Min.
70 ns
Max.
Min.
Max.
Unit
Read Cycle
tRC
Read Cycle Time
45
tAA
Address to Data Valid
tOHA
Data Hold from Address Change
tACE
CE LOW to Data Valid
45
55
70
ns
tDOE
OE LOW to Data Valid
25
25
35
ns
25
ns
45
[13]
tLZOE
OE LOW to LOW Z
tHZOE
OE HIGH to High Z[13, 14]
tLZCE
CE LOW to Low Z[13]
tHZCE
CE HIGH to High
55
10
55
10
5
10
ns
10
20
ns
25
tPU
CE LOW to Power-Up
CE HIGH to Power-Down
45
55
70
ns
tDBE
BLE/BHE LOW to Data Valid
25
25
35
ns
tLZBE
tHZBE
BLE/BHE LOW to Low
BLE/BHE HIGH to HIGH
10
Z[13, 14]
0
ns
tPD
Z[13]
0
ns
ns
5
10
0
70
20
20
ns
10
5
15
Z[13, 14]
70
10
15
ns
10
20
ns
25
ns
Write Cycle[15]
tWC
Write Cycle Time
45
55
70
ns
tSCE
CE LOW to Write End
40
40
60
ns
tAW
Address Set-up to Write End
40
40
60
ns
tHA
Address Hold from Write End
0
0
0
ns
tSA
Address Set-up to Write Start
0
0
0
ns
tPWE
WE Pulse Width
35
40
45
ns
tBW
BLE/BHE LOW to Write End
40
40
60
ns
tSD
Data Set-up to Write End
25
25
30
ns
tHD
Data Hold from Write End
0
0
0
ns
tHZWE
tLZWE
WE LOW to
High-Z[13, 14]
[13]
WE HIGH to Low-Z
15
10
20
10
25
10
ns
ns
Notes:
12. Test conditions for all parameters other than three-state parameters assume signal transition time of 3 ns (1V/ns) or less, timing reference levels of VCC(typ)/2,
input pulse levels of 0 to VCC(typ.), and output loading of the specified IOL/IOH as shown in the “AC Test Loads and Waveforms” section.
13. At any given temperature and voltage condition, tHZCE is less than tLZCE, tHZBE is less than tLZBE, tHZOE is less than tLZOE, and tHZWE is less than tLZWE for any
given device.
14. tHZOE, tHZCE, tHZBE, and tHZWE transitions are measured when the outputs enter a high-impedence state.
15. The internal Write time of the memory is defined by the overlap of WE, CE = VIL, BHE and/or BLE = VIL. All signals must be ACTIVE to initiate a write and any
of these signals can terminate a write by going INACTIVE. The data input set-up and hold timing should be referenced to the edge of the signal that terminates
the write.
Document #: 38-05339 Rev. *A
Page 5 of 11
CY62146DV30
Switching Waveforms
Read Cycle 1 (Address Transition Controlled)[16, 17]
tRC
ADDRESS
tOHA
DATA OUT
tAA
DATA VALID
PREVIOUS DATA VALID
Read Cycle No. 2 (OE Controlled)[17, 18]
ADDRESS
tRC
CE
tPD
tHZCE
tACE
OE
tHZOE
tDOE
BHE/BLE
tLZOE
tHZBE
tDBE
tLZBE
DATA OUT
HIGH IMPEDANCE
HIGH
IMPEDANCE
DATA VALID
tLZCE
VCC
SUPPLY
CURRENT
tPU
50%
50%
ICC
ISB
Notes:
16. The device is continuously selected. OE, CE = VIL, BHE and/or BLE = VIL.
17. WE is HIGH for read cycle.
18. Address valid prior to or coincident with CE and BHE, BLE transition LOW.
Document #: 38-05339 Rev. *A
Page 6 of 11
CY62146DV30
Switching Waveforms (continued)
Write Cycle No. 1 (WE Controlled)[15, 19, 20]
tWC
ADDRESS
tSCE
CE
tAW
tHA
tSA
WE
tPWE
tBW
BHE/BLE
OE
tSD
DATA I/O
tHD
DATAIN
NOTE 21
tHZOE
Write Cycle No. 2 (CE Controlled)[15, 19, 20]
tWC
ADDRESS
tSCE
CE
tSA
tAW
tHA
tPWE
WE
tBW
BHE/BLE
OE
tSD
DATA I/O
tHD
DATAIN
NOTE 21
tHZOE
Notes:
19. Data I/O is high impedance if OE = VIH.
20. If CE goes HIGH simultaneously with WE = VIH, the output remains in a high-impedance state.
21. During this period, the I/Os are in output state and input signals should not be applied.
Document #: 38-05339 Rev. *A
Page 7 of 11
CY62146DV30
Switching Waveforms (continued)
Write Cycle No. 3 (WE Controlled, OE LOW)[20]
tWC
ADDRESS
tSCE
CE
tBW
BHE/BLE
tAW
tHA
tSA
tPWE
WE
tSD
DATAI/O
NOTE 21
tHD
DATAIN
tHZWE
tLZWE
Write Cycle No. 4 (BHE/BLE Controlled, OE LOW)[20]
tWC
ADDRESS
CE
tSCE
tAW
tHA
tBW
BHE/BLE
tSA
tPWE
WE
tHZWE
DATA I/O
NOTE 21
tSD
tHD
DATAIN
tLZWE
Document #: 38-05339 Rev. *A
Page 8 of 11
CY62146DV30
Truth Table
CE
WE
OE
BHE
BLE
Inputs/Outputs
Mode
Power
H
X
X
X
X
High Z
Deselect/Power-Down
Standby (ISB)
L
X
X
H
H
High Z
Output Disabled
Active (ICC)
L
H
L
L
L
Data Out (I/OO–I/O15)
Read
Active (ICC)
L
H
L
H
L
Data Out (I/OO–I/O7);
I/O8–I/O15 in High Z
Read
Active (ICC)
L
H
L
L
H
Data Out (I/O8–I/O15);
I/O0–I/O7 in High Z
Read
Active (ICC)
L
H
H
L
L
High Z
Output Disabled
Active (ICC)
L
H
H
H
L
High Z
Output Disabled
Active (ICC)
L
H
H
L
H
High Z
Output Disabled
Active (ICC)
L
L
X
L
L
Data In (I/OO–I/O15)
Write
Active (ICC)
L
L
X
H
L
Data In (I/OO–I/O7);
I/O8–I/O15 in High Z
Write
Active (ICC)
L
L
X
L
H
Data In (I/O8–I/O15);
I/O0–I/O7 in High Z
Write
Active (ICC)
Ordering Information
Speed
(ns)
45
Ordering Code
CY62146DV30LL-45BVI
Package
Name
BV48A
CY62146DV30LL-45BVXI
55
Package Type
48-ball Very Fine Pitch BGA (6 mm × 8mm × 1 mm)
Industrial
48-ball Very Fine Pitch BGA (6 mm × 8mm × 1 mm) (Pb-free)
CY62146DV30LL-45ZSXI
ZS-44
44-pin TSOP II (Pb-free)
CY62146DV30L-55BVI
BV48A
48-ball Very Fine Pitch BGA (6 mm × 8mm × 1 mm)
CY62146DV30L-55BVXI
Industrial
48-ball Very Fine Pitch BGA (6 mm × 8mm × 1 mm)
(Pb-free)
CY62146DV30LL-55BVI
48-ball Very Fine Pitch BGA (6 mm × 8mm × 1 mm)
CY62146DV30LL-55BVXI
48-ball Very Fine Pitch BGA (6 mm × 8mm × 1 mm)
(Pb-free)
CY62146DV30L-55ZSXI
Operating
Range
ZS-44
44-pin TSOP II (Pb-free)
BV48A
48-ball Very Fine Pitch BGA (6 mm × 8mm × 1 mm)
CY62146DV30LL-55ZSXI
70
CY62146DV30L-70BVI
CY62146DV30L-70BVXI
48-ball Very Fine Pitch BGA (6 mm × 8mm × 1 mm)
(Pb-free)
CY62146DV30LL-70BVI
48-ball Very Fine Pitch BGA (6 mm × 8mm × 1 mm)
CY62146DV30LL-70BVXI
48-ball Very Fine Pitch BGA (6 mm × 8mm × 1 mm)
(Pb-free)
CY62146DV30L-70ZSXI
Industrial
ZS-44
44-pin TSOP II (Pb-free)
Industrial
CY62146DV30LL-70ZSXI
Document #: 38-05339 Rev. *A
Page 9 of 11
CY62146DV30
Package Diagram
48-Lead VFBGA (6 x 8 x 1 mm) BV48A
51-85150-*B
44-Pin TSOP II ZS44
51-85087-*A
MoBL is a registered trademark, and More Battery Life is a trademark, of Cypress Semiconductor. All product and company
names mentioned in this document may be the trademarks of their respective holders.
Document #: 38-05339 Rev. *A
Page 10 of 11
© Cypress Semiconductor Corporation, 2005. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
CY62146DV30
Document History Page
Document Title:CY62146DV30 MoBL® 4-Mbit (256K x 16) Static RAM
Document Number: 38-05339
REV.
ECN NO. Issue Date
Orig. of
Change
Description of Change
**
213251
See ECN
AJU
New Data Sheet
*A
316039
See ECN
PCI
Added 45-ns Speed Bin in AC, DC and Ordering Information tables
Added Footnote #10 on page #4
Added Pb-free package ordering information on page # 9
Changed 44-lead TSOP-II package name on page 10 from Z44 to ZS44
Standardized Icc values across ‘L’ and ‘LL’ bins
Document #: 38-05339 Rev. *A
Page 11 of 11