5 Tap High Speed CMOS (HCT) Compatible Active Delay Lines Delays are ±5% or ±2 nS† Tap Total 12* 17 12* 18 12* 19 12* 20 12* 21 12* 22 12* 24 15 30 20 40 25 50 30 60 35 70 40 80 50 100 60 120 70 140 22 24 26 28 30 32 36 45 60 75 90 105 120 150 180 210 27 30 33 36 39 42 48 60 80 100 120 140 160 200 240 280 †Whichever is greater. 32 36 40 44 48 52 60 75 100 125 150 175 200 250 300 350 * Inherent Delay DIP Part Number EP9604-32 EP9604-36 EP9604-40 EP9604-44 EP9604-48 EP9604-52 EP9604-60 EP9604-75 EP9604-100 EP9604-125 EP9604-150 EP9604-175 EP9604-200 EP9604-250 EP9604-300 EP9604-350 SMD Part Number Delays are ±5% or ±2 nS† Tap Total EP9604G-32 EP9604G-36 EP9604G-40 EP9604G-44 EP9604G-48 EP9604G-52 EP9604G-60 EP9604G-75 EP9604G-100 EP9604G-125 EP9604G-150 EP9604G-175 EP9604G-200 EP9604G-250 EP9604G-300 EP9604G-350 80 84 88 90 100 110 120 130 140 150 160 170 180 190 200 High Level Input Voltage Low Level Input Voltage High Level Output Voltage VOL Low Level Output Voltage IL I CCL TRO Input Leakage Current Supply Current Output Rise Time NH High Fanout VCC 320 400 336 420 352 440 360 450 400 500 440 550 480 600 520 650 560 700 600 750 640 800 680 850 720 900 760 950 800 1000 EP9604-400 EP9604-420 EP9604-440 EP9604-450 EP9604-500 EP9604-550 EP9604-600 EP9604-650 EP9604-700 EP9604-750 EP9604-800 EP9604-850 EP9604-900 EP9604-950 EP9604-1000 EP9604G-400 EP9604G-420 EP9604G-440 EP9604G-450 EP9604G-500 EP9604G-550 EP9604G-600 EP9604G-650 EP9604G-700 EP9604G-750 EP9604G-800 EP9604G-850 EP9604G-900 EP9604G-950 EP9604G-1000 Schematic Min Max Unit VCC = 4.5 to 5.5 VCC = 4.5 to 5.5 VCC = 4.5V,IO= -4.0mA @ VIH or VIL VCC = 4.5V,IO = 4.0mA @ VIH or VIL VCC = 5.5V @ VIH or VIL VCC = 5.5V, VIN = 0 ≤550 nS (.75 - 2.4 Volts) >550 nS VCC = 5.5V, VOH = 4.0V Input Pulse Test Conditions @ 25°C EIN PW TRI PRR 240 252 264 270 300 330 360 390 420 450 480 510 540 570 600 SMD Part Number • Delay times referenced from input to leading edges at 25°C, 5.0V. DC Electrical Characteristics Parameter Test Conditions VIH VIL VOH 160 168 176 180 200 220 240 260 280 300 320 340 360 380 400 DIP Part Number Unit Pulse Input Voltage Pulse Width % of Total Delay Input Rise Time (0.75 - 2.4 Volts) Pulse Repetition Rate @ PW ≤ 500nS Pulse Repetition Rate @ PW > 500nS Supply Voltage 3.2 150 2.0 1.0 100 5.0 Volts % nS MHz KHz Volts 2.0 0.8 Volt Volt Volt 0.3 Volt 4.0 10 14 VCC 12 6 8 OUTPUT INPUT 1 7 GROUND ±1.0 uA 15 mA 4 nS 5 nS LSTTL Load Recommended Operating Conditions VCC VI VO IO PW* D* TA 10 4 Min DC Supply Voltage DC Input Voltage Range DC Output Voltage Range DC Output Source/Sink Current Pulse Width % of Total Delay Duty Cycle Operating Free Air Temperature 4.5 0 0 Max Unit 5.5 VCC VCC 25 Volt Volt Volt mA % % °C 40 0 40 70 *These two values are inter-dependent. SMD Package DIP Package .200 .200 PCA EP9604G-32 Date Code .400 Max. .280 Max. Suggested Solder Pad Layout .055 White Dot Pin#1 .410 PCA EP9604G-32 Date Code .300 .300 .200 .300 .02 .780 Max. .01 Typ. DSD9604/G Rev. A .100 .100 .03 .780 Max. .250 Max. .280 Max. .020 Min. .250 Max. .050 .300 .020 Typ. .150 Typ. .365 Max. 2/5/96 Unless Otherwise Noted Dimensions in Inches Tolerances: Fractional = ± 1/32 .XX = ± .030 .XXX = ± .010 .010 Typ. QAF-CSO1a Rev. B 8/25/94 ELECTRONICS INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 TEL: (818) 892-0761 FAX: (818) 894-5791