14 Pin DIP and SMD 5 Tap Both Edges Controlled Fast Logic TTL Compatible Active Delay Lines Compatible with standard auto-insertable equipment and can be used in either infrared or vapor phase process. Input to Tap ± 5% or ± 2nS† Tap to Tap ± 7% or ± 2nS† Tap Total 5, 10, 15, 20 6, 12, 18, 24 7, 14, 21, 28 8, 16, 24, 32 9, 18, 27, 36 10, 20, 30, 40 12, 24, 36, 48 15, 30, 45, 60 20, 40, 60, 80 25, 50, 75, 100 30, 60, 90, 120 35, 70, 105, 140 25 30 35 40 45 50 60 75 100 125 150 175 DIP Part Number SMD Part Number EPA3507-25 EPA3507-30 EPA3507-35 EPA3507-40 EPA3507-45 EPA3507-50 EPA3507-60 EPA3507-75 EPA3507-100 EPA3507-125 EPA3507-150 EPA3507-175 EPA3507G-25 EPA3507G-30 EPA3507G-35 EPA3507G-40 EPA3507G-45 EPA3507G-50 EPA3507G-60 EPA3507G-75 EPA3507G-100 EPA3507G-125 EPA3507G-150 EPA3507G-175 Input to Tap ± 5% or ± 2nS† Tap to Tap ± 7% or ± 2nS† Tap Total 40, 80, 120, 160 45, 90, 135, 180 50, 100, 150, 200 60, 120, 180, 240 70, 140, 210, 280 80, 160, 240, 320 84, 168, 252, 336 88, 176, 264, 352 90, 180, 270, 360 84, 188, 282, 376 100, 200, 300, 400 200 225 250 300 350 400 420 440 450 470 500 DIP Part Number SMD Part Number EPA3507-200 EPA3507-225 EPA3507-250 EPA3507-300 EPA3507-350 EPA3507-400 EPA3507-420 EPA3507-440 EPA3507-450 EPA3507-470 EPA3507-500 EPA3507G-200 EPA3507G-225 EPA3507G-250 EPA3507G-300 EPA3507G-350 EPA3507G-400 EPA3507G-420 EPA3507G-440 EPA3507G-450 EPA3507G-470 EPA3507G-500 Delay measured @ 1.5V levels on leading and trailing edge w/ 15pF load on taps. Rise and Fall Time measured from 0.75 to 2.4V level. Electrical Characteristics Schematic Parameter Test Conditions Min. Max. Unit †Whichever is greater. VOH VOL VIK IIH IIL IOS High-Level Output Voltage Low-Level Output Voltage Input Clamp Voltage High-Level Input Current Low-Level Input Current Short Circuit Output Current VCC = Min. V IL = Max. I OH = Max. 2.7 V VCC = Min. VIH = Min. I OL= Max. 0.5 V VCC = Min. II = IIK -1.2 V VCC = Max. V IN = 2.7V 20 µA VCC = Max. V IN = 0.5V -0.6 mA VCC = Max. V OUT = 0. -60 -150 mA (One output at a time) I CCH High-Level Supply Current VCC = Max. V IN = OPEN 25 mA ICCL Low-Level Supply Current VCC = Max. V IN = 0 40 mA TRO Output Rise Time Td ≤ 500 nS (0.75 to 2.4 Volts) 4 nS Td > 500 nS 5 nS NH Fanout High-Level Output VCC = Max. V OH = 2.7V 20 TTL LOAD NL Fanout Low-Level Output VCC = Max. V OL = 0.5V 10 TTL LOAD TC Temp. Coeff. of Total Delay 100 + (25000/TD) PPM/°C TSTG Storage Temp. Range -20 °C to +100 °C Input Pulse Test Conditions @ 25° C EIN PW TRI PRR VCC Pulse Input Voltage Pulse Width 1.2X Total Delay Pulse Rise Time (10 - 90%) Pulse Repetition Rate 4X P W Supply Voltage 3.2 --3.0 --5.0 Volts nS nS MHz Volts 4 10 6 8 OUTPUT INPUT 1 7 GROUND Recommended Operating Conditions VCC VIH VIL IIK IOH IOL PW* d* TA Min. Max. Unit Supply Voltage 4.75 5.25 High-Level Input Voltage 2.0 Low-Level Input Voltage 0.8 Input Clamp Current -18 High-Level Output Current -1.0 Low-Level Output Current 20 Input Pulse Width of Total Delay 40 Duty Cycle 50 Operating Free-Air Temperature 0 +70 V V V mA mA mA % % °C DIP Package .085 Typ. PCA EPA3507G-XX Date Code .300 Typ. .200 .270 Suggested Solder Pad Layout .200 .055 PCA EPA3507-XX Date Code Pin 1 I.D. .420 .200 Typ. .300 .300 .030 .010 ± .005 .215 .010 Typ. 0°-8° .035 .380 .100 Typ. DSA3507G-XX & DSA3507-XX .280 Max. .100 .780 Max. .770 .019 ± .002 12 VCC *These two values are inter-dependent. SMD Package Pin 1 I.D. Unit 14 .020 Min. .250 Max. .020 Typ. .125 ± .010 Rev. - 7/22/98 Unless Otherwise Noted Dimensions in Inches Tolerances: Fractional = ± 1/32 .XX = ± .030 .XXX = ± .010 .365 Max. .010 Typ. QAF-CSO1 Rev. B 8/25/94 ELECTRONICS INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 TEL: (818) 892-0761 FAX: (818) 894-5791