FPD1000AS Datasheet v3.0 1W PACKAGED POWER PHEMT FEATURES: • • • • • • • • PACKAGE 31 dBm Output Power (P1dB) @1.8GHz 15 dB Power Gain (G1dB) @ 1.8GHz 43 dBm Output IP3 -42 dBc WCDMA ACPR at 21 dBm PCH 10V Operation 50% Power-Added Efficiency Evaluation Boards Available Suitable for applications to 5 GHz TYPICAL APPLICATIONS: • GENERAL DESCRIPTION: The FPD1000AS is a packaged depletion mode AlGaAs/InGaAs pseudomorphic High Electron Mobility Transistor (pHEMT), optimized for power applications in L-Band. The surface-mount package has been optimized for low parasitics. • Drivers or output stages in PCS/Cellular base station transmitter amplifiers Power applications in WLL/WLAN and WiMax amplifiers ELECTRICAL SPECIFICATIONS: PARAMETER SYMBOL CONDITIONS MIN TYP 30 31 13.5 15.0 MAX UNITS VDS = 10V; IDS = 200 mA Power at 1dB Gain Compression P1dB ΓS and ΓL tuned for Optimum IP3 dBm VDS = 10V; IDS = 200 mA Power Gain at 1dB Gain Compression G1dB ΓS and ΓL tuned for Optimum IP3 VDS = 10 V; IDS = 200mA Maximum Stable Gain MSG S21/S12 dB 50 % VDS = 10V; IDS = 200 mA Power-Added Efficiency PAE at 1dB Gain Compression 3rd-Order Intermodulation Distortion ΓS and ΓL tuned for Optimum IP3 20 PIN = 0dBm, 50Ω system ΓS and ΓL tuned for Optimum IP3 VDS = 10V; IDS = 200 mA IM3 -46 POUT = 19 dBm (single-tone level) dBc Saturated Drain-Source Current IDSS VDS = 1.3 V; VGS = 0 V 480 650 800 Maximum Drain-Source Current IMAX VDS = 1.3 V; VGS ≅ +1 V 1100 mA Transconductance GM VDS = 1.3 V; VGS = 0 V 720 mS Gate-Source Leakage Current IGSO VGS = -3 V 20 50 µA Pinch-Off Voltage |VP| VDS = 1.3 V; IDS = 2.4 mA 0.7 0.9 1.4 V Gate-Source Breakdown Voltage |VBDGS| IGS = 2.4 mA 6 V Gate-Drain Breakdown Voltage |VBDGD| IGD = 2.4 mA 20 V Thermal Resistance (channel-to-case) ΘCC See Note on following page 25 mA °C/W Note: TAMBIENT = 22°; RF specification measured at f = 1850 MHz using CW signal (except as noted) 1 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FPD1000AS Datasheet v3.0 1 ABSOLUTE MAXIMUM RATING : PARAMETER SYMBOL TEST CONDITIONS ABSOLUTE MAXIMUM 7 Drain-Source Voltage VDS -3V < VGS < -0.5V 12V Gate-Source Voltage VGS 0V < VDS < +8V -3V Drain-Source Current IDS For VDS > 2V IDSS Gate Current IG Forward or reverse current +20/-20mA RF Input Power PIN Under any acceptable bias state 27.5dBm Channel Operating Temperature TCH Under any acceptable bias state 175°C Storage Temperature TSTG Non-Operating Storage -40°C to 150°C PTOT See De-Rating Note below 6W 2 3 Total Power Dissipation Notes: 1 TAmbient = 22°C unless otherwise noted; exceeding any one of these absolute maximum ratings may cause permanent damage to the device; Users should avoid exceeding 80% of 2 or more Limits simultaneously 2 Max. RF Input Limit must be further limited if input VSWR > 2.5:1 3 Total Power Dissipation defined as: PTOT ≡ (PDC + PIN) – POUT, where PDC: DC Bias Power, PIN: RF Input Power, POUT: RF Output Power Total Power Dissipation to be de-rated as follows above 22°C: PTOT= 6 - (0.04W/°C) x TPACK where TPACK= source tab lead temperature above 22°C (coefficient of de-rating formula is the Thermal Conductivity) Example: For a 55°C carrier temperature: PTOT = 6W – (0.04 x (55 – 22)) = 4.68W 5 For optimum heatsinking, metal-filled through (Source) via holes should be used directly below the central metallized ground pad on the bottom of the package 6 Thermal Resistivity: The nominal value of 25°C/W is measured with the package mounted on a large heatsink with thermal compound to ensure adequate (unsoldered) contact. The package temperature is referred to the Source leads. 7 Operating at absolute maximum VD continuously is not recommended. If operation is considered then IDS must be reduced in order to keep the part within it's thermal power dissipation limits. Therefore VGS is restricted to <-0.5V. BIASING GUIDELINES: • • • Active bias circuits provide good performance stabilization over variations of operating temperature, but require a larger number of components compared to self-bias or dual-biased. Such circuits should include provisions to ensure that Gate bias is applied before Drain bias, otherwise the pHEMT may be induced to self-oscillate. Contact your Sales Representative for additional information. Dual-bias circuits are relatively simple to implement, but will require a regulated negative voltage supply for depletion-mode devices such as the FPD1000AS. The recommended 200mA bias point is nominally a Class AB mode. A small amount of RF gain expansion prior to the onset of compression is normal for this operating point. RECOMMENDED OPERATING BIAS CONDITIONS: • • Drain-Source Voltage: Quiescent Current: From 5V to 10V From 25% IDSS to 55% IDSS 2 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FPD1000AS Datasheet v3.0 TYPICAL MEASURED RF PERFORMANCE: Note: Measurement Conditions TAMBIENT = 22°C unless otherwise stated (VDS=10V, IDS=200mA, f=1800MHz) Power Transfer Characteristic Drain Efficiency and PAE 3.50 31.00 70.00% 70.00% 60.00% 60.00% 3.00 29.00 Pout 21.00 Comp Point 1.00 19.00 .50 17.00 .00 15.00 0.00 2.00 4.00 6.00 8.00 10.00 12.00 14.00 Eff. 40.00% 30.00% 30.00% 20.00% 20.00% 10.00% 10.00% .00% 0.00 -.50 18.00 16.00 50.00% PAE 40.00% 2.00 4.00 6.00 8.00 10.00 12.00 14.00 16.00 Drain Efficiency (%) 1.50 23.00 50.00% PAE (%) Output Power (dBm) 2.00 25.00 Gain Compression (dB) 2.50 27.00 .00% 18.00 Input Power (dBm) Input Power (dBm) IMProductsvs. Input Power FPD1000AS I-V Curves -15.00 .800 27.00 -20.00 VGS = 0V .700 Pout -30.00 Im3, dBc 23.00 -35.00 -40.00 21.00 IM Products (dBc) Output Power (dBm) 25.00 Drain-Source Current (A) -25.00 -45.00 VGS = -0.25V .600 .500 VGS = -0.5V .400 .300 VGS = -0.75V .200 19.00 17.00 2.00 3.00 4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 VGS = -1.0V -50.00 .100 -55.00 .000 0.00 12.00 VGS = -1.25V 1.00 2.00 3.00 5.00 1.0 FPD1000AS IP3 CONTOURS 1800 MHz 2.0 0.6 2.0 0.4 3.0 28 dBm 29 dBm 30 dBm 3.0 4.0 5.0 0.2 5.0 31 dBm 0.2 32 dBm 0.2 10.0 5.0 4.0 3.0 2.0 1.0 0.8 0.6 0.4 10.0 0.2 0.4 0.6 10.0 0.8 1.0 2.0 10. 0 3.0 4.0 5.0 0 -10.0 -10.0 -0.2 -0.2 -5.0 -5.0 -4.0 -4.0 -3.0 - 3. 0 -0.4 .0 -2 .4 -0 -1.0 -0.8 -0.6 8.00 Swp Max 215 1.0 0.8 0.6 4.0 0 7.00 FPD1000AS POWER CONTOURS 1800 MHz Swp Max 222 0. 4 48 dBm 46 dBm 44 dBm 42 dBm 40 dBm 6.00 Drain-Source Voltage (V) Input Power(dBm) 0.8 4.00 0.6 Swp Min 1 2.0 0.8 1.0 Swp Min 1 NOTE: Power contours measured at constant input power level set to meet Optimum P1dB at the output match. Optimum match: ΓS = 3 – j2 Ω and ΓL = 25 + j5 Ω NOTE: IP3 contours generated with PIN = 11dB back-off from P1dB. Local maxima for best linearity located at: ΓL = 40 + j55 Ω and ΓL = 113 + j70 Ω with ΓS = 15 + j12 Ω 3 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FPD1000AS Datasheet v3.0 TYPICAL MEASURED RF PERFORMANCE: Note: Measurement Conditions TAMBIENT = 22°C unless otherwise stated (VDS=10V, IDS=200mA) FPD1000AS at VDS = 10V and IDS = 200mA FPD1000AS WCDMA ACPR 1900 MHz DOWNLINK Pk/Avg = 9dB 0.01% 30.0 40 0 30 -10 25.0 20 Output Power (dBm) Ga in 15.0 (dB) S21 MSG 10.0 0 -30 -10 -40 Output Power -20 ACPR (5 MHz) -30 ACPR (10MHz) -50 -40 5.0 -60 -50 -60 0.0 0 500 1000 1500 2000 2500 3000 3500 4000 -70 3 4 5 6 7 8 9 10 11 12 13 Input Power (dBm) Frequency (MHz) AS PACKAGE OUTLINE AND RECOMMENDED PC BOARD LAYOUT: (dimensions in millimeters – mm) 3.8 0 to 0.3 4 Plcs. 0.35 2 Plcs. 0.5 2 Plcs. 4.4 0.35 2 Plcs. 3.8 2.2±0.25 1.9±0.25 1.3 2 Plcs. 3.2 0.15 1.5 Epoxy Fillet All Dimnesions in mm General Tolerance: .xx ± 0.05 .x ± 0.15 For best positional accuracy in auto pick and place device should be referenced directly from the leads 4 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com 14 ACPR (dBc) -20 10 20.0 FPD1000AS Datasheet v3.0 REFERENCE DESIGN AT 1.70 TO 1.85 GHZ: VGG ≈ -0.5V VDD = +10V C6 C8 R2 C7 C5 L2 RF INPUT C4 R1 C9 L1 C1 C2 Q1 RF OUTPUT NOTE: AutoCAD™ drawing available on request DESIGNATOR MANUFACTURER’S PART DESCRIPTION C1 C2 C4 C5 C6 C7 C8 C9 L1 L2 R1 R2 Q1 ATC600S3R9CW250 ATC600S5R6CW250 ATC600S330JW250 ATC600S330JW250 T491B105M035AS7015 ATC600S680JW250 T491B105M035AS7015 ATC600S2R0BW250 0604HQ-1N1 0604HQ-1N1 RCI-0402-27R0J RCI-0603-12R0J FPD1000AS PC-SP-000010-006 TF-SP-000012 142-0711-841 AMP-103185-2 TF-SP-000003 Capacitor, 3.9 pF, 0603, ATC 600, tol. +0.25pF Capacitor, 5.6 pF, 0603, ATC 600, tol. +0.25pF Capacitor, 33 pF, 0603, ATC 600, tol. +5% Capacitor, 33 pF, 0603, ATC 600, tol. +5% Capacitor, 1 mF, SMD-B, Kemet, tol. +20% Capacitor, 68 pF, 0603, ATC 600 Capacitor, 1 mF, SMD-B, Kemet, tol. +20% Capacitor, 2 pF, 0603, ATC 600, tol. +0.1pF Inductor, 1.1 nH, Coilcraft High Q Surface Mount Inductor, 1.1 nH, Coilcraft High Q Surface Mount Resistor, 27 W, 0402, IMS, tol. +5% Resistor, 12 W, 0603, IMS, tol. +5% 1w Packaged Power pHEMT, Filtronic PCB, Rogers R04003, 0.012”(0.3mm), 0.5oz. QUANTITY 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Carrier 1 Connector, RF, SMA End Launch, Jack Assy, 2 Connector, DC, 0.100 on center, 0.025 sq. 2 Center Block for P100 Package 1 Screw, #0-80 8 NOTE: 10-12 mil (0.3mm) plated thru vias used; vias under Q1 should be filled with Dupont CB100 conductive via plugging material in order to achieve optimal heatsinking. 5 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FPD1000AS Datasheet v3.0 REFERENCE DESIGN AT 3.4 TO 3.5 GHZ: PARAMETER UNIT PERFORMANCE Frequency GHz 3.4 to 3.5 Gain dB 12 P1dB dBm 31 IM3@19dBm Pout SCL dBc -46dBc S11 dB -5 S22 dB -19 Vd V 10 Vg V -0.6 to -0.9 Id mA 200 SCHEMATIC: Vd -Vg 1.0uF 1.0uF 100pF FPD1000AS EVAL Board Schematic 10pF 10pF 20 Ohm Z16 Z10 Z15 Z9 1 RF IN (50 Ohm) Z5 Z1 15pF 2 4 1 3 Z2 Z1 Z3 2 4 1 3 Z4 Z5 Z14 Z8 Z6 2 4 1 Z12 3 Z7 Z11 2 4 15pF 3 Z13 Z17 Z18 Z19 RF OUT (50 Ohm) Z14 Z8 Desc. Value 0.040" x 0.930" Microstrip Z1 W1=0.020" W2=0.040" W3=0.020" W4=0.040" Microstrip Cross Z2 0.020" x 0.140" Microstrip Z3 W1=0.020" W2=0.080" W3=0.020" W4=0.080" Microstrip Cross Z4 0.080" x 0.100" Microstrip Z5 0.020" x 0.350" Microstrip Z6 W1=0.020" W2=0.060" W3=0.020" W4=0.060" Microstrip Cross Z7 0.060" x 0.320" Microstrip Z8 0.015" x 0.256" Microstrip Z9 Z10, Z16 0.400" x 90° Microstrip Radial Stub Z11, Z12 0.040" x 0.040" Microstrip W1=0.040" W2=0.120" W3=0.040" W4=0.120" Microstrip Cross Z13 0.120" x 0.220" Microstrip Z14 0.015" x 0.330" Microstrip Z15 0.040" x 0.320" Microstrip Z17 0.150" x 0.140" Microstrip Z18 0.030" x 0.270" Microstrip Z19 6 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FPD1000AS Datasheet v3.0 BOARD LAYOUT 3.4 TO 3.5 GHZ: VD RF IN EV-SP-000017-002 NOTE: AutoCAD™ drawing available on request 7 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FPD1000AS Datasheet v3.0 S-PARAMETERS: Note: Biased @ 10V, 200mA FREQ-GHZ 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00 2.10 2.20 2.30 2.40 2.50 2.60 2.70 2.80 2.90 3.00 3.10 3.20 3.30 3.40 3.50 3.60 3.70 3.80 3.90 4.00 4.10 4.20 4.30 4.40 4.50 4.60 4.70 4.80 4.90 S11MAG 0.88 0.87 0.87 0.87 0.86 0.86 0.86 0.86 0.86 0.86 0.86 0.86 0.86 0.86 0.86 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.84 0.84 0.84 0.83 0.83 0.83 0.82 0.82 0.82 0.82 0.82 0.82 S11ANG -128.80 -138.81 -146.73 -153.30 -158.82 -163.57 -167.75 -171.53 -174.94 -178.08 178.98 176.28 173.71 171.32 168.97 166.76 164.62 162.52 160.59 158.68 156.79 154.99 153.27 151.54 149.70 148.18 146.56 145.00 143.46 141.96 140.50 139.18 137.91 133.28 131.33 129.25 127.24 125.13 123.09 120.85 118.85 116.97 114.89 112.68 110.43 S21MAG 15.67 13.51 11.82 10.51 9.47 8.59 7.86 7.23 6.72 6.26 5.86 5.51 5.20 4.93 4.68 4.46 4.26 4.07 3.91 3.75 3.61 3.48 3.36 3.25 3.14 3.05 2.95 2.87 2.79 2.71 2.64 2.57 2.50 2.55 2.51 2.47 2.42 2.38 2.34 2.31 2.28 2.24 2.21 2.18 2.15 S21ANG 106.53 100.36 95.18 90.63 86.53 82.82 79.41 76.19 73.13 70.17 67.33 64.62 61.95 59.34 56.77 54.27 51.80 49.34 46.97 44.57 42.21 39.86 37.54 35.25 32.97 30.71 28.46 26.22 24.00 21.75 19.55 17.37 15.34 12.52 10.15 7.62 5.19 2.91 0.60 -1.66 -4.25 -6.61 -8.92 -11.33 -13.72 S12MAG 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.06 0.06 0.06 0.06 S12ANG 28.11 24.30 21.50 19.18 17.49 15.99 14.99 13.89 13.12 12.20 11.65 11.00 10.43 10.09 9.33 9.11 8.72 8.23 7.91 7.48 6.98 6.55 6.11 5.76 5.67 5.28 4.73 4.39 3.80 3.47 2.94 2.37 2.17 1.14 0.41 -0.73 -1.59 -2.45 -3.33 -4.30 -5.16 -6.12 -7.13 -7.96 -8.99 S22MAG 0.28 0.28 0.28 0.28 0.28 0.28 0.28 0.28 0.28 0.28 0.29 0.29 0.29 0.29 0.29 0.29 0.29 0.30 0.30 0.30 0.30 0.30 0.30 0.31 0.31 0.31 0.31 0.31 0.31 0.31 0.32 0.32 0.32 0.30 0.30 0.30 0.30 0.30 0.30 0.29 0.29 0.29 0.29 0.29 0.29 S22ANG -125.75 -134.41 -140.94 -146.22 -150.43 -154.02 -156.96 -159.56 -161.88 -163.82 -165.60 -167.20 -168.79 -170.11 -171.44 -172.55 -173.63 -174.74 -175.59 -176.51 -177.41 -178.34 -179.07 -179.86 179.17 178.58 177.94 177.26 176.65 176.12 175.68 175.37 174.54 171.63 170.81 169.88 168.68 167.57 166.08 164.67 163.90 162.91 161.64 160.21 158.83 8 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FPD1000AS Datasheet v3.0 S-PARAMETERS (CONT.): Biased 10V, 200mA FREQ-GHZ 5.00 5.10 5.20 5.30 5.40 5.50 5.60 5.70 5.80 5.90 6.00 6.10 6.20 6.30 6.40 6.50 6.60 6.70 6.80 6.90 7.00 7.10 7.20 7.30 7.40 7.50 7.60 7.70 7.80 7.90 8.00 8.10 8.20 8.30 8.40 8.50 8.60 8.70 8.80 8.90 9.00 9.10 9.20 9.30 9.40 9.50 9.60 9.70 9.80 9.90 10.00 S11MAG 0.82 0.81 0.81 0.81 0.81 0.81 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.79 0.79 0.78 0.79 0.79 0.79 0.79 0.79 0.79 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.81 0.81 0.81 0.81 0.81 0.81 0.81 0.81 0.81 0.82 0.82 0.82 0.82 0.82 0.82 0.83 0.82 0.82 S11ANG 108.18 105.83 103.46 101.13 98.72 96.33 93.92 91.39 88.80 86.30 83.78 81.27 78.66 76.05 73.44 70.67 67.95 65.31 63.23 61.09 58.43 55.67 52.99 50.30 47.73 45.33 42.75 40.08 37.57 34.99 32.44 30.01 27.63 25.29 22.80 20.44 18.12 15.80 13.42 11.15 8.87 6.58 4.40 2.09 -0.07 -2.41 -4.64 -7.03 -9.45 -11.95 -14.29 S21MAG 2.13 2.10 2.08 2.05 2.03 2.00 1.98 1.96 1.93 1.91 1.89 1.87 1.85 1.82 1.80 1.78 1.75 1.72 1.71 1.71 1.70 1.68 1.66 1.64 1.62 1.61 1.59 1.57 1.55 1.53 1.52 1.50 1.48 1.47 1.45 1.43 1.42 1.40 1.39 1.37 1.36 1.35 1.34 1.33 1.32 1.30 1.29 1.28 1.27 1.26 1.25 S21ANG -16.13 -18.60 -21.11 -23.59 -26.08 -28.59 -31.11 -33.62 -36.18 -38.70 -41.23 -43.77 -46.41 -49.03 -51.60 -54.20 -56.75 -59.02 -60.71 -63.43 -66.42 -69.26 -71.95 -74.59 -77.04 -79.49 -82.36 -85.07 -87.69 -90.32 -92.91 -95.45 -97.99 -100.59 -103.20 -105.74 -108.27 -110.78 -113.31 -115.81 -118.27 -120.72 -123.22 -125.78 -128.34 -130.90 -133.47 -136.06 -138.66 -141.19 -143.71 S12MAG 0.06 0.06 0.06 0.07 0.07 0.07 0.07 0.07 0.07 0.07 0.07 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.09 0.09 0.09 0.09 0.09 0.10 0.10 0.10 0.10 0.10 0.11 0.11 0.11 0.11 0.11 0.11 0.11 0.12 0.12 0.12 0.12 0.12 0.12 0.13 0.13 0.13 0.13 0.13 0.13 0.14 0.14 0.14 S12ANG -9.98 -11.10 -12.35 -13.63 -14.83 -16.07 -17.49 -18.72 -20.03 -21.39 -22.73 -24.19 -26.10 -27.81 -29.44 -30.98 -32.63 -33.63 -32.15 -33.13 -35.89 -38.30 -40.44 -42.24 -43.66 -44.69 -46.91 -49.10 -51.11 -53.07 -55.02 -56.92 -58.66 -60.57 -62.43 -64.13 -65.92 -67.73 -69.56 -71.48 -73.28 -75.07 -76.87 -78.81 -80.75 -82.67 -84.62 -86.70 -88.65 -90.55 -92.29 S22MAG 0.29 0.29 0.29 0.29 0.29 0.29 0.29 0.29 0.29 0.29 0.29 0.29 0.29 0.29 0.29 0.29 0.29 0.28 0.28 0.29 0.30 0.30 0.30 0.30 0.30 0.30 0.31 0.31 0.31 0.32 0.32 0.32 0.32 0.32 0.32 0.33 0.33 0.33 0.33 0.33 0.33 0.33 0.33 0.33 0.34 0.34 0.34 0.34 0.34 0.34 0.34 S22ANG 157.42 155.91 154.46 152.90 151.36 149.74 148.11 146.28 144.50 142.74 141.04 139.39 137.34 135.24 133.07 130.98 128.65 126.73 126.99 126.51 124.01 121.40 118.89 116.47 114.40 113.31 110.92 108.33 105.97 103.61 101.30 99.02 96.94 94.64 92.31 89.97 87.60 85.33 83.03 80.64 78.35 76.22 74.12 71.85 69.43 67.07 64.55 62.06 59.65 57.31 54.97 9 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FPD1000AS Datasheet v3.0 TAPE AND REEL DIMENSIONS AND PART ORIENTATION f xxx xxx PACKAGE MARKING CODE Example: f1ZD P2F f = Filtronic 1ZD = Lot / Date Code P2F = Status, Part Code, Part Type Parts per reel 178mm = 1000 330mm = 2500 10 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FPD1000AS Datasheet v3.0 PREFERRED ASSEMBLY INSTRUCTIONS: ORDERING INFORMATION: This package is compatible with both lead free and leaded solder reflow processes as defined within IPC/JEDEC J-STD-020C. The maximum package temperature should not exceed 260°C. Package leads are gold plated. PART NUMBER DESCRIPTION FPD1000AS Packaged pHEMT FPD1000AS-EB Packaged pHEMT evaluation board EB-1000AS-AB (880MHz) EB-1000AS-AA (1.85GHz) HANDLING PRECAUTIONS: EB-1000AS-AD (2.14GHz) EB-1000AS-AG (2.5 to 2.7GHz) To avoid damage to the devices care should be exercised during handling. Proper Electrostatic Discharge (ESD) precautions should be observed at all stages of storage, handling, assembly, and testing. EB-1000AS-AH (3.5GHz) ESD/MSL RATING: These devices should be treated as Class 1A (250-500 V) as defined in JEDEC Standard No. 22-A114. Further information on ESD control measures can be found in MIL-STD1686 and MIL-HDBK-263. The device has a MSL rating of Level 1. To determine this rating, preconditioning was performed to the device per, the Pb-free solder profile defined within IPC/JEDEC J-STD-020C, Moisture / Reflow sensitivity classification for non-hermatic solid state surface mount devices APPLICATION NOTES & DESIGN DATA: Application Notes and design data including Sparameters, noise parameters and device model are available on request. DISCLAIMERS: This product is not designed for use in any space based or life sustaining/supporting equipment. 11 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com