DU C T NT E PRO T E CE M E a t L A O L P E OBS R Center ND E D OMME ical Support .com/tsc C E R NO hn Data ersil ecSheet ww.int t o ur T contac TERSIL or w IN 1-888- HA5013 ® November 2004 FN3654.5 Triple, 125MHz Video Amplifier Features The HA5013 is a low cost triple amplifier optimized for RGB video applications and gains between 1 and 10. It is a current feedback amplifier and thus yields less bandwidth degradation at high closed loop gains than voltage feedback amplifiers. • Wide Unity Gain Bandwidth . . . . . . . . . . . . . . . . . 125MHz The low differential gain and phase, 0.1dB gain flatness, and ability to drive two back terminated 75Ω cables, make this amplifier ideal for demanding video applications. • Slew Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475V/µs • Input Offset Voltage . . . . . . . . . . . . . . . . . . . . . . . . 800µV • Differential Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.03% • Differential Phase. . . . . . . . . . . . . . . . . . . . . 0.03 Degrees • Supply Current (Per Amplifier) . . . . . . . . . . . . . . . . 7.5mA • ESD Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4000V The current feedback design allows the user to take advantage of the amplifier’s bandwidth dependency on the feedback resistor. The performance of the HA5013 is very similar to the popular Intersil HA-5020 single video amplifier. • Guaranteed Specifications at ±5V Supplies • Low Cost Applications • PC Add-On Multimedia Boards Pinout • Flash A/D Driver HA5013 (PDIP, SOIC) TOP VIEW • Color Image Scanners • CCD Cameras and Systems NC 1 14 OUT2 NC 2 NC 3 12 +IN2 V+ 4 11 V- +IN1 5 10 +IN3 -IN1 6 9 -IN3 OUT1 7 8 OUT3 +- + + 13 -IN2 - • RGB Cable Driver • RGB Video Preamp • PC Video Conferencing Part Number Information PART NUMBER PACKAGE PKG. NO. HA5013IP -40 to 85 14 Ld PDIP E14.3 HA5013IB -40 to 85 14 Ld SOIC M14.15 - HA5025EVAL 1 TEMP. RANGE (oC) High Speed Op Amp DIP Evaluation Board CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 1999, 2004. All Rights Reserved All other trademarks mentioned are the property of their respective owners. HA5013 Absolute Maximum Ratings Thermal Information Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . 36V DC Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±VSUPPLY Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10V Output Current (Note 2) . . . . . . . . . . . . . . . . Short Circuit Protected ESD Rating (Note 4) Human Body Model (Per MIL-STD-883 Method 3015.7) . . . . 2000V Thermal Resistance (Typical, Note 1) Operating Conditions θJA (oC/W) PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Maximum Junction Temperature (Die Only, Note 3). . . . . . . . . 175oC Maximum Junction Temperature (Plastic Package, Note 3) . . 150oC Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC Supply Voltage Range (Typical) . . . . . . . . . . . . . . . . ±4.5V to ±15V CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. θJA is measured with the component mounted on an evaluation PC board in free air. 2. Output is protected for short circuits to ground. Brief short circuits to ground will not degrade reliability, however, continuous (100% duty cycle) output current should not exceed 15mA for maximum reliability. 3. Maximum power dissipation, including output load, must be designed to maintain junction temperature below 175oC for die, and below 150oC for plastic packages. See Application Information section for safe operating area information. 4. The non-inverting input of unused amplifiers must be connected to GND. VSUPPLY = ±5V, RF = 1kΩ, AV = +1, RL = 400Ω, CL ≤10pF, Unless Otherwise Specified Electrical Specifications (NOTE 9) TEST LEVEL TEMP. (oC) MIN TYP MAX UNITS A 25 - 0.8 3 mV A Full - - 5 mV Delta VIO Between Channels A Full - 1.2 3.5 mV Average Input Offset Voltage Drift B Full - 5 - µV/oC A 25 53 - - dB A Full 50 - - dB A 25 60 - - dB A Full 55 - - dB A Full ±2.5 - - V A 25 - 3 8 µA A Full - - 20 µA A 25 - - 0.15 µA/V A Full - - 0.5 µA/V A 25 - - 0.1 µA/V A Full - - 0.3 µA/V A 25, 85 - 4 12 µA A -40 - 10 30 µA A 25, 85 - 6 15 µA A -40 - 10 30 µA PARAMETER TEST CONDITIONS INPUT CHARACTERISTICS Input Offset Voltage (VIO) VIO Common Mode Rejection Ratio VIO Power Supply Rejection Ratio VCM = ±2.5V (Note 5) ±3.5V ≤ VS ≤ ±6.5V VCM = ±2.5V (Note 5) Input Common Mode Range Non-Inverting Input (+IN) Current +IN Common Mode Rejection (+IBCMR = 1 +RIN VCM = ±2.5V (Note 5) ) ±3.5V ≤ VS ≤ ±6.5V +IN Power Supply Rejection Inverting Input (-IN) Current Delta - IN BIAS Current Between Channels 2 HA5013 VSUPPLY = ±5V, RF = 1kΩ, AV = +1, RL = 400Ω, CL ≤10pF, Unless Otherwise Specified (Continued) Electrical Specifications PARAMETER TEST CONDITIONS VCM = ±2.5V (Note 5) -IN Common Mode Rejection ±3.5V ≤ VS ≤ ±6.5V -IN Power Supply Rejection (NOTE 9) TEST LEVEL TEMP. (oC) MIN TYP MAX UNITS A 25 - - 0.4 µA/V A Full - - 1.0 µA/V A 25 - - 0.2 µA/V A Full - - 0.5 µA/V Input Noise Voltage f = 1kHz B 25 - 4.5 - nV/√Hz +Input Noise Current f = 1kHz B 25 - 2.5 - pA/√Hz -Input Noise Current f = 1kHz B 25 - 25.0 - pA/√Hz VOUT = ±2.5V (Note 11) A 25 1.0 - - MΩ A Full 0.85 - - MΩ A 25 70 - - dB A Full 65 - - dB A 25 50 - - dB A Full 45 - - dB A 25 ±2.5 ±3.0 - V A Full ±2.5 ±3.0 - V TRANSFER CHARACTERISTICS Transimpedence RL = 400Ω, VOUT = ±2.5V Open Loop DC Voltage Gain RL = 100Ω, VOUT = ±2.5V Open Loop DC Voltage Gain OUTPUT CHARACTERISTICS Output Voltage Swing RL = 150Ω Output Current RL = 150Ω B Full ±16.6 ±20.0 - mA Short Circuit Output Current VIN = ±2.5V, VOUT = 0V A Full ±40 ±60 - mA Supply Voltage Range A 25 5 - 15 V Quiescent Supply Current A Full - 7.5 10 mA/Op Amp B 25 275 350 - V/µs B 25 22 28 - MHz POWER SUPPLY CHARACTERISTICS AC CHARACTERISTICS AV = +1 Slew Rate Note 6 Full Power Bandwidth (Note 7) Rise Time (Note 8) VOUT = 1V, RL = 100Ω B 25 - 6 - ns Fall Time (Note 8) VOUT = 1V, RL = 100Ω B 25 - 6 - ns Propagation Delay (Note 8) VOUT = 1V, RL = 100Ω B 25 - 6 - ns B 25 - 4.5 - % Overshoot -3dB Bandwidth VOUT = 100mV B 25 - 125 - MHz Settling Time To 1%, 2V Output Step B 25 - 50 - ns Settling Time To 0.25%, 2V Output Step B 25 - 75 - ns Note 6 B 25 - 475 - V/µs AC CHARACTERISTICS AV = +2, RF = 681Ω Slew Rate 3 HA5013 VSUPPLY = ±5V, RF = 1kΩ, AV = +1, RL = 400Ω, CL ≤10pF, Unless Otherwise Specified (Continued) Electrical Specifications PARAMETER TEST CONDITIONS Full Power Bandwidth (Note 7) (NOTE 9) TEST LEVEL TEMP. (oC) MIN TYP MAX UNITS B 25 - 26 - MHz Rise Time (Note 8) VOUT = 1V, RL = 100Ω B 25 - 6 - ns Fall Time (Note 8) VOUT = 1V, RL = 100Ω B 25 - 6 - ns Propagation Delay (Note 8) VOUT = 1V, RL = 100Ω B 25 - 6 - ns B 25 - 12 - % Overshoot -3dB Bandwidth VOUT = 100mV B 25 - 95 - MHz Settling Time To 1%, 2V Output Step B 25 - 50 - ns Settling Time To 0.25%, 2V Output Step B 25 - 100 - ns Gain Flatness 5MHz B 25 - 0.02 - dB 20MHz B 25 - 0.07 - dB Note 6 B 25 350 475 - V/µs B 25 28 38 - MHz AC CHARACTERISTICS AV = +10, RF = 383Ω Slew Rate Full Power Bandwidth (Note 7) Rise Time (Note 8) VOUT = 1V, RL = 100Ω B 25 - 8 - ns Fall Time (Note 8) VOUT = 1V, RL = 100Ω B 25 - 9 - ns Propagation Delay (Note 8) VOUT = 1V, RL = 100Ω B 25 - 9 - ns B 25 - 1.8 - % Overshoot -3dB Bandwidth VOUT = 100mV B 25 - 65 - MHz Settling Time To 1%, 2V Output Step B 25 - 75 - ns To 0.1%, 2V Output Step B 25 - 130 - ns Differential Gain RL = 150Ω, (Note 10) B 25 - 0.03 - % Differential Phase RL = 150Ω, (Note 10) B 25 - 0.03 - Degrees VIDEO CHARACTERISTICS NOTES: 5. At -40oC Product is tested at VCM = ±2.25V because Short Test Duration does not allow self heating. 6. VOUT switches from -2V to +2V, or from +2V to -2V. Specification is from the 25% to 75% points. Slew Rate 7. FPBW = ----------------------------; V = 2V . 2πV PEAK PEAK 8. Measured from 10% to 90% points for rise/fall times; from 50% points of input and output for propagation delay. 9. A. Production Tested; B. Typical or Guaranteed Limit based on characterization; C. Design Typical for information only. 10. Measured with a VM700A video tester using an NTC-7 composite VITS. 11. At -40oC Product is tested at VOUT = ±2.25V because Short Test Duration does not allow self heating. 4 HA5013 Test Circuits and Waveforms + DUT 50Ω HP4195 NETWORK ANALYZER 50Ω FIGURE 1. TEST CIRCUIT FOR TRANSIMPEDANCE MEASUREMENTS (NOTE 12) 100Ω (NOTE 12) 100Ω VIN + VIN DUT VOUT - 50Ω RL 100Ω + DUT VOUT - 50Ω RI 681Ω RF , 681Ω RL 400Ω RF , 1kΩ FIGURE 2. SMALL SIGNAL PULSE RESPONSE CIRCUIT FIGURE 3. LARGE SIGNAL PULSE RESPONSE CIRCUIT NOTE: 12. A series input resistor of ≥100Ω is recommended to limit input currents in case input signals are present before the HA5013 is powered up. Vertical Scale: VIN = 100mV/Div., VOUT = 100mV/Div. Horizontal Scale: 20ns/Div. Vertical Scale: VIN = 1V/Div., VOUT = 1V/Div. Horizontal Scale: 50ns/Div. FIGURE 4. SMALL SIGNAL RESPONSE FIGURE 5. LARGE SIGNAL RESPONSE 5 Schematic (One Amplifier of Three) V+ R10 820 R5 2.5K R2 800 QP8 R19 400 R15 400 QP9 QP14 QP11 QP1 QP5 R11 1K R17 280 QN5 R24 140 6 QP10 C1 1.4pF R28 20 QP6 -IN R12 280 QP4 QP17 QN13 +IN QN17 R25 20 C2 1.4pF QN15 QN2 R21 140 QN10 QN3 R14 280 QP7 QN4 R22 280 QN14 R16 400 QN21 R25 140 QN16 R13 1K QN7 HA5013 QP13 R3 6K D1 QP20 QP12 QN6 QN1 QP16 R20 140 QP15 QN8 QP2 R1 60K QP19 R31 5 R18 280 QN12 R29 9.5 R27 200 QN18 R23 R26 400 200 R32 5 QN19 R30 7 OUT R4 800 V- R33 800 R9 820 QN9 QN11 HA5013 Application Information as short as possible to minimize the capacitance from this node to ground. Optimum Feedback Resistor The plots of inverting and non-inverting frequency response, see Figure 8 and Figure 9 in the typical performance section, illustrate the performance of the HA5013 in various closed loop gain configurations. Although the bandwidth dependency on closed loop gain isn’t as severe as that of a voltage feedback amplifier, there can be an appreciable decrease in bandwidth at higher gains. This decrease may be minimized by taking advantage of the current feedback amplifier’s unique relationship between bandwidth and RF . All current feedback amplifiers require a feedback resistor, even for unity gain applications, and RF , in conjunction with the internal compensation capacitor, sets the dominant pole of the frequency response. Thus, the amplifier’s bandwidth is inversely proportional to RF . The HA5013 design is optimized for a 1000Ω RF at a gain of +1. Decreasing RF in a unity gain application decreases stability, resulting in excessive peaking and overshoot. At higher gains the amplifier is more stable, so RF can be decreased in a trade-off of stability for bandwidth. The table below lists recommended RF values for various gains, and the expected bandwidth. GAIN (ACL) RF (Ω) BANDWIDTH (MHz) -1 750 100 +1 1000 125 +2 68f1 95 +5 1000 52 +10 383 65 -10 750 22 Driving Capacitive Loads Capacitive loads will degrade the amplifier’s phase margin resulting in frequency response peaking and possible oscillations. In most cases the oscillation can be avoided by placing an isolation resistor (R) in series with the output as shown in Figure 6. 100Ω VIN R + VOUT CL RT RF RI FIGURE 6. PLACEMENT OF THE OUTPUT ISOLATION RESISTOR, R The selection criteria for the isolation resistor is highly dependent on the load, but 27Ω has been determined to be a good starting value. Power Dissipation Considerations Due to the high supply current inherent in triple amplifiers, care must be taken to insure that the maximum junction temperature (TJ , see Absolute Maximum Ratings) is not exceeded. Figure 7 shows the maximum ambient temperature versus supply voltage for the available package styles (PDIP, SOIC). At VS = ±5V quiescent operation both package styles may be operated over the full industrial range of -40oC to 85oC. It is recommended that thermal calculations, which take into account output power, be performed by the designer. PC Board Layout Attention must be given to decoupling the power supplies. A large value (10µF) tantalum or electrolytic capacitor in parallel with a small value (0.1µF) chip capacitor works well in most cases. 130 MAX. AMBIENT TEMPERATURE (oC) The frequency response of this amplifier depends greatly on the amount of care taken in designing the PC board. The use of low inductance components such as chip resistors and chip capacitors is strongly recommended. If leaded components are used the leads must be kept short especially for the power supply decoupling components and those components connected to the inverting input. 120 100 90 7 SOIC 80 70 60 50 40 30 20 10 A ground plane is strongly recommended to control noise. Care must also be taken to minimize the capacitance to ground seen by the amplifier’s inverting input (-IN). The larger this capacitance, the worse the gain peaking, resulting in pulse overshoot and possible instability. It is recommended that the ground plane be removed under traces connected to -IN, and that connections to -IN be kept PDIP 110 5 7 9 11 13 15 SUPPLY VOLTAGE (±V) FIGURE 7. MAXIMUM OPERATING AMBIENT TEMPERATURE vs SUPPLY VOLTAGE HA5013 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified 5 5 VOUT = 0.2VP-P CL = 10pF AV = +1, RF = 1kΩ 3 AV = 2, RF = 681Ω 2 AV = 5, RF = 1kΩ 1 0 -1 -2 -3 3 AV = -1 2 1 AV = -2 0 -1 -2 AV = -10 -3 AV = 10, RF = 383Ω -4 AV = -5 -4 -5 -5 10 FREQUENCY (MHz) 100 200 2 +90 AV = -1, RF = 750Ω +45 AV = +10, RF = 383Ω -100 0 -225 -45 -270 -90 AV = -10, RF = 750Ω -315 -135 VOUT = 0.2VP-P CL = 10pF 2 -180 10 100 140 VOUT = 0.2VP-P CL = 10pF AV = +1 130 -3dB BANDWIDTH 120 5 GAIN PEAKING 200 500 700 FIGURE 10. PHASE RESPONSE AS A FUNCTION OF FREQUENCY 1100 1300 0 1500 FIGURE 11. BANDWIDTH AND GAIN PEAKING vs FEEDBACK RESISTANCE 130 VOUT = 0.2VP-P CL = 10pF AV = +2 95 -3dB BANDWIDTH 90 10 5 GAIN PEAKING 500 650 800 950 FEEDBACK RESISTOR (Ω) 0 1100 FIGURE 12. BANDWIDTH AND GAIN PEAKING vs FEEDBACK RESISTANCE 8 -3dB BANDWIDTH (MHz) 100 GAIN PEAKING (dB) -3dB BANDWIDTH (MHz) 900 FEEDBACK RESISTOR (Ω) FREQUENCY (MHz) 350 10 120 -3dB BANDWIDTH 110 6 100 4 90 GAIN PEAKING VOUT = 0.2VP-P CL = 10pF AV = +1 80 0 200 400 600 800 2 0 1000 LOAD RESISTOR (Ω) FIGURE 13. BANDWIDTH AND GAIN PEAKING vs LOAD RESISTANCE GAIN PEAKING (dB) -360 -3dB BANDWIDTH (MHz) +180 +135 -45 -135 200 FIGURE 9. INVERTING FREQUENCY RESPONSE INVERTING PHASE (DEGREES) AV = +1, RF = 1kΩ -90 100 FREQUENCY (MHz) FIGURE 8. NON-INVERTING FREQUENCY RESPONSE 0 10 GAIN PEAKING (dB) 2 NON-INVERTING PHASE (DEGREES) VOUT = 0.2VP-P CL = 10pF RF = 750Ω 4 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 4 HA5013 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 16 VOUT = 0.1VP-P CL = 10pF VOUT = 0.2VP-P CL = 10pF AV = +10 60 OVERSHOOT (%) -3dB BANDWIDTH (MHz) 80 40 VSUPPLY = ±5V, AV = +2 12 VSUPPLY = ±15V, AV = +2 6 20 VSUPPLY = ±5V, AV = +1 VSUPPLY = ±15V, AV = +1 0 0 200 350 500 650 FEEDBACK RESISTOR (Ω) 800 0 950 800 1000 0.08 DIFFERENTIAL PHASE (DEGREES) FREQUENCY = 3.58MHz 0.08 RL = 75Ω 0.06 RL = 150Ω 0.04 0.02 FREQUENCY = 3.58MHz 0.06 0.04 RL = 150Ω RL = 75Ω 0.02 RL = 1kΩ RL = 1kΩ 3 5 7 9 11 13 0.00 15 3 5 7 9 11 SUPPLY VOLTAGE (±V) SUPPLY VOLTAGE (±V) FIGURE 16. DIFFERENTIAL GAIN vs SUPPLY VOLTAGE VOUT = 2.0VP-P CL = 30pF 0 REJECTION RATIO (dB) HD2 -60 3RD ORDER IMD HD2 HD3 AV = +1 -20 -30 -40 -50 CMRR -60 -70 -80 NEGATIVE PSRR -80 POSITIVE PSRR HD3 -90 0.3 15 -10 -50 -70 13 FIGURE 17. DIFFERENTIAL PHASE vs SUPPLY VOLTAGE -40 DISTORTION (dBc) 600 FIGURE 15. SMALL SIGNAL OVERSHOOT vs LOAD RESISTANCE 0.10 0.00 400 LOAD RESISTANCE (Ω) FIGURE 14. BANDWIDTH vs FEEDBACK RESISTANCE DIFFERENTIAL GAIN (%) 200 1 FREQUENCY (MHz) FIGURE 18. DISTORTION vs FREQUENCY 9 10 0.001 0.01 0.1 1 FREQUENCY (MHz) 10 FIGURE 19. REJECTION RATIOS vs FREQUENCY 30 HA5013 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 12 RL = 100Ω VOUT = 1.0VP-P AV = +1 RLOAD = 100Ω VOUT = 1.0VP-P PROPAGATION DELAY (ns) PROPAGATION DELAY (ns) 8.0 7.5 7.0 6.5 AV = +10, RF = 383Ω 8 AV = +2, RF = 681Ω 6 AV = +1, RF = 1kΩ 4 6.0 -50 -25 0 25 50 75 TEMPERATURE (oC) 100 3 125 FIGURE 20. PROPAGATION DELAY vs TEMPERATURE 5 7 9 11 SUPPLY VOLTAGE (±V) 13 15 FIGURE 21. PROPAGATION DELAY vs SUPPLY VOLTAGE 0.8 500 VOUT = 2VP-P NORMALIZED GAIN (dB) + SLEW RATE 400 VOUT = 0.2VP-P CL = 10pF 0.6 450 SLEW RATE (V/µs) 10 350 - SLEW RATE 300 250 200 0.4 0.2 AV = +2, RF = 681Ω 0 -0.2 -0.4 AV = +5, RF = 1kΩ -0.6 AV = +1, RF = 1kΩ -0.8 150 -1.0 100 -1.2 -50 -25 0 25 50 75 100 TEMPERATURE (oC) FIGURE 22. SLEW RATE vs TEMPERATURE 10 125 AV = +10, RF = 383Ω 5 10 15 20 FREQUENCY (MHz) 25 FIGURE 23. NON-INVERTING GAIN FLATNESS vs FREQUENCY 30 HA5013 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 0.8 VOUT = 0.2VP-P CL = 10pF RF = 750Ω 0.2 AV = -1 0 -0.2 -0.4 -0.6 AV = -5 -0.8 -1.0 -INPUT NOISE CURRENT 80 -1.2 600 60 +INPUT NOISE CURRENT 400 40 INPUT NOISE VOLTAGE 200 20 10 15 20 25 0 0.01 30 0.1 FREQUENCY (MHz) 1 FIGURE 25. INPUT NOISE CHARACTERISTICS 1.5 BIAS CURRENT (µA) 2 VIO (mV) 1.0 0.5 0 -2 -4 -40 -20 0 20 40 60 80 100 120 -60 140 -40 -20 0 40 60 80 100 120 140 FIGURE 27. +INPUT BIAS CURRENT vs TEMPERATURE FIGURE 26. INPUT OFFSET VOLTAGE vs TEMPERATURE 4000 TRANSIMPEDANCE (kΩ) 22 BIAS CURRENT (µA) 20 TEMPERATURE (oC) TEMPERATURE (oC) 20 18 16 -60 0 100 10 FREQUENCY (kHz) FIGURE 24. INVERTING GAIN FLATNESS vs FREQUENCY 0.0 -60 800 AV = -2 AV = -10 5 1000 AV = +10, RF = 383Ω CURRENT NOISE (pA/√Hz) 0.4 100 VOLTAGE NOISE (nV/√Hz) NORMALIZED GAIN (dB) 0.6 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (oC) FIGURE 28. -INPUT BIAS CURRENT vs TEMPERATURE 11 140 3000 2000 1000 -60 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (oC) FIGURE 29. TRANSIMPEDANCE vs TEMPERATURE 140 HA5013 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 74 25 REJECTION RATIO (dB) ICC (mA) 20 55oC 15 10 3 4 5 6 70 68 -PSRR 66 64 62 CMRR 60 25oC 5 +PSRR 72 125oC 7 8 9 10 11 12 13 14 58 -100 15 -50 0 100 200 150 250 FIGURE 31. REJECTION RATIO vs TEMPERATURE FIGURE 30. SUPPLY CURRENT vs SUPPLY VOLTAGE 4.0 40 +10V 30 +15V +5V OUTPUT SWING (V) SUPPLY CURRENT (mA) 50 TEMPERATURE (oC) SUPPLY VOLTAGE (±V) 20 3.8 10 3.6 0 0 1 2 3 4 5 6 7 8 9 -60 10 11 12 13 14 15 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE (oC) DISABLE INPUT VOLTAGE (V) FIGURE 32. SUPPLY CURRENT vs DISABLE INPUT VOLTAGE FIGURE 33. OUTPUT SWING vs TEMPERATURE 30 1.2 VS = ±15V 1.1 VIO (mV) VOUT (VP-P) 20 VS = ±10V 1.0 10 0.9 VS = ±4.5V 0 0.8 0.01 0.10 1.00 LOAD RESISTANCE (kΩ) FIGURE 34. OUTPUT SWING vs LOAD RESISTANCE 12 10.00 -60 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (oC) FIGURE 35. INPUT OFFSET VOLTAGE CHANGE BETWEEN CHANNELS vs TEMPERATURE 140 HA5013 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) -30 1.5 -40 SEPARATION (dB) ∆BIAS CURRENT (µA) AV = +1 VOUT = 2VP-P 1.0 0.5 -50 -60 -70 0.0 -40 -20 0 20 40 60 80 TEMPERATURE (oC) 100 120 -80 0.1 140 0 DISABLE = 0V VIN = 5VP-P RF = 750Ω -20 -30 -40 -50 30 10 RL = 100Ω 1 0.1 0.01 180 0.001 135 90 45 -60 0 -70 -45 -80 -90 1 FREQUENCY (MHz) 10 0.001 20 0.01 1 10 -135 100 FREQUENCY (MHz) FIGURE 38. DISABLE FEEDTHROUGH vs FREQUENCY FIGURE 39. TRANSIMPEDANCE vs FREQUENCY 10 RL = 400Ω 1 0.1 0.01 180 0.001 135 90 45 0 -45 -90 -135 0.001 0.01 0.1 1 10 100 FREQUENCY (MHz) FIGURE 40. TRANSIMPEDENCE vs FREQUENCY 13 0.1 PHASE ANGLE (DEGREES) 0.1 TRANSIMPEDANCE (MΩ) FEEDTHROUGH (dB) -10 10 FIGURE 37. CHANNEL SEPARATION vs FREQUENCY TRANSIMPEDANCE (MΩ) FIGURE 36. INPUT BIAS CURRENT CHANGE BETWEEN CHANNELS vs TEMPERATURE 1 FREQUENCY (MHz) PHASE ANGLE (DEGREES) -60 HA5013 Die Characteristics DIE DIMENSIONS: PASSIVATION: 2010µm x 3130µm x 483µm Type: Nitride Thickness: 4kÅ ±0.4kÅ METALLIZATION: TRANSISTOR COUNT: Type: Metal 1: AlCu (1%) Thickness: Metal 1: 8kÅ ±0.4kÅ 248 Type: Metal 2: AlCu (1%) Thickness: Metal 2: 16kÅ ±0.8kÅ PROCESS: High Frequency Bipolar Dielectric Isolation SUBSTRATE POTENTIAL Unbiased Metallization Mask Layout HA5013 NC NC OUT2 -IN2 NC +IN2 V+ V- +IN1 +IN3 -IN1 OUT1 OUT3 -IN3 All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 14