HS-390RH-T TM Data Sheet July 1999 FN4604.1 Radiation Hardened CMOS Dual SPDT Analog Switch Features Intersil’s Satellite Applications Flow TM (SAF) devices are fully tested and guaranteed to 100kRAD total dose. This QML Class T device is processed to a standard flow intended to meet the cost and shorter lead-time needs of large volume satellite manufacturers, while maintaining a high level of reliability. • Radiation Performance - Gamma Dose (γ) 1 x 105 RAD(Si) - No Latch-Up, Dielectrically Isolated Device Islands • QML Class T, Per MIL-PRF-38535 • Pin for Pin Compatible with Intersil HI-390 Series Analog Switches The HS-390RH-T analog switch is a monolithic device fabricated using Radiation Hardened CMOS technology and the Intersil dielectric isolation process for latch-up free operation. Improved total dose hardness is obtained by layout (thin oxide tabs extending to a channel stop) and processing (hardened gate oxide). These switches offer lowresistance switching performance for analog voltages up to the supply rails. “ON” resistance is low and stays reasonably constant over the full range of operating voltage and current. “ON” resistance also stays reasonably constant when exposed to radiation, being typically 30Ω pre-rad and 35Ω post 100kRAD(Si). Break-before-make switching is controlled by 5V digital inputs. • Analog Signal Range 15V • Low Leakage . . . . . . . . . . . . . . . . 100nA (Max, Post Rad) • Low rON . . . . . . . . . . . . . . . . . . . . . . 60Ω (Max, Post Rad) • Low Operating Power. . . . . . . . . . 100µA (Max, Post Rad) Pinouts HS1-390RH (SBDIP), CDIP2-T16 TOP VIEW D1 1 16 S1 NC 2 15 IN1 D3 3 14 V- S3 4 13 GND S4 5 12 NC Specifications D4 6 11 V+ Specifications for Rad Hard QML devices are controlled by the Defense Supply Center in Columbus (DSCC). The SMD numbers listed below must be used when ordering. NC 7 10 IN2 D2 8 9 S2 Detailed Electrical Specifications for the HS-390RH-T are contained in SMD 5962-95813. A “hot-link” is provided from our website for downloading. www.intersil.com/spacedefense/newsafclasst.asp HS9-390RH (FLATPACK), CDFP4-F16 TOP VIEW D1 NC D3 Intersil’s Quality Management Plan (QM Plan), listing all Class T screening operations, is also available on our website. www.intersil.com/quality/manuals.asp S3 D2 Ordering Information PART NUMBER 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 S1 IN1 VGND NC S4 D4 NC ORDERING NUMBER 1 TEMP. RANGE (oC) 5962R9581303TEC HS1-390RH-T -55 to 125 5962R9581303TYC HS9-390RH-T -55 to 125 V+ IN2 S2 Functional Diagram IN N P D NOTE: Minimum order quantity for -T is 150 units through distribution, or 450 units direct. TRUTH TABLE 1 LOGIC SW1 SW2 SW3 SW4 0 OFF ON 1 ON OFF CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2002. All Rights Reserved Satellite Applications Flow™ (SAF) is a trademark of Intersil Corporation. HS-390RH-T Die Characteristics PASSIVATION: DIE DIMENSIONS: (2130µm x 1930µm x 279µm ±25.4µm) Type: Silox (SiO2) 84 x 76 x 11mils ±1mil Thickness: 8.0kÅ ±1.0kÅ WORST CASE CURRENT DENSITY: METALLIZATION: < 2.0e5 A/cm 2 Type: Al Thickness: 12.5kÅ ±2kÅ TRANSISTOR COUNT: SUBSTRATE POTENTIAL: 76 Unbiased (DI) PROCESS: BACKSIDE FINISH: Metal Gate CMOS, Dielectric Isolation Gold Metallization Mask Layout IN1 S1 D1 D3 HS-390RH-T S3 VGND S4 IN2 S2 D2 D4 V+ All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation 7585 Irvine Center Drive Suite 100 Irvine, CA 92618 TEL: (949) 341-7000 FAX: (949) 341-7123 Intersil Corporation 2401 Palm Bay Rd. Palm Bay, FL 32905 TEL: (321) 724-7000 FAX: (321) 724-7946 2 EUROPE Intersil Europe Sarl Ave. William Graisse, 3 1006 Lausanne Switzerland TEL: +41 21 6140560 FAX: +41 21 6140579 ASIA Intersil Corporation Unit 1804 18/F Guangdong Water Building 83 Austin Road TST, Kowloon Hong Kong TEL: +852 2723 6339 FAX: +852 2730 1433