ADVANCE INFORMATION ICS845204 CRYSTAL-TO-MLVDS PCI EXPRESS™ CLOCK SYNTHESIZER W/SPREAD SPECTRUM General Description Features The ICS845204 is a 4 output PCI Express clock synthesizer optimized to generate low jitter PCI HiPerClockS™ Express™ reference clocks with or without spread spectrum modulation and is a member of the HiPerClockS™ family of high performance clock solutions from IDT. Spread type and amount can be configured via the SSC control pins. Using a 25MHz, 18pF parallel resonant crystal, the device will generate M-LVDS clocks at either 25MHz, 100MHz, 125MHz or 250MHz. The ICS845204 uses a low jitter VCO that easily meets PCI Express jitter requirements and is packaged in a 32-pin VFQFN package. • • Four differential spread spectrum clock outputs • Crystal oscillator interface designed for 18pF, 25MHz parallel resonant crystal • Supports the following output frequencies: 25MHz, 100MHz, 125MHz or 250MHz • • VCO range: 250MHz - 700MHz • • • • • Cycle-to-cycle jitter: 50ps (maximum) design target ICS Q1 nQ1 nc VDDA OE1 GND Q0 nQ0 Pin Assignment 32 31 30 29 28 27 26 25 OE0 1 24 nc VDD 2 23 nc nQ3 3 22 GND Q3 4 21 Q2 VDDO 5 20 nQ2 19 SSC1 7 18 nc nc 8 17 GND OE2 Supports SSC downspread at 0.05% and -0.75%, centerspread at ±0.25% and no spread options Period jitter, RMS: TBD Full 3.3V output supply mode 0°C to 70°C ambient operating temperature Available in both standard (RoHS 5) and lead-free (RoHS 6) packages GND XTAL_OUT XTAL_IN VDD 10 11 12 13 14 15 16 OE3 9 SSC0 6 FSEL1 nc FSEL0 Each output can be individually disabled by separate output-enable inputs ICS845204 32 Lead VFQFN 5mm x 5mm x 0.925mm package body K Package Top View Block Diagram 00 PLL Bypass 01 10 11 ÷5 ÷4 ÷2 25MHz Q0 nQ0 XTAL_IN Phase Detector OSC VCO 250-700MHz XTAL_OUT Pullup OE0 Q1 nQ1 Pullup OE1 Feedback Divider ÷20 Q2 nQ2 Pullup OE2 2 SSC[1:0] Pullup:Pullup FSEL[1:0] Default = 100MHz Pulldown:Pullup 2 Spread Spectrum Control Q3 nQ3 Pullup OE3 The Advance Information presented herein represents a product that is developmental or prototype. The noted characteristics are design targets. Integrated Device Technologies, Inc. (IDT) reserves the right to change any circuitry or specifications without notice. IDT™ / ICS™ M-LVDS CLOCK SYNTHESIZER 1 ICS845204AK SEPTEMBER 25, 2007 ICS845204 CRYSTAL-TO-MLVDS CLOCK SYNTHESIZER W/SPREAD SPECTRUM ADVANCE INFORMATION Table 1. Pin Descriptions Number Name Type Description 1 OE0 Input 2, 11 VDD Power Core supply pins. 3, 4 nQ3, Q3 Output Differential output pair. M-LVDS interface levels. 5 VDDO Power Output supply pin. 6, 8, 18, 23, 24, 27 nc Unused 7 FSEL0 Input Pullup Output frequency select pins. See Table 3A. LVCMOS/LVTTL interface levels. 9 FSEL1 Input Pulldown Output frequency select pin. See Table 3A. LVCMOS/LVTTL interface levels. 10, 19 SSC0, SSC1 Input Pullup Spread spectrum control pins. See Table 3B. LVCMOS/LVTTL interface levels. 12 OE3 Input Pullup Output enable pin for Q3/nQ3 outputs. Logic High, outputs are enabled. Logic LOW, outputs are in Hi-Z. LVCMOS/LVTTL interface levels. 13, 14 XTAL_IN XTAL_OUT Input 15 OE2 Input Output enable pin for Q0/nQ0 outputs. Logic High, outputs are enabled. Logic LOW, outputs are in Hi-Z. LVCMOS/LVTTL interface levels. Pullup No connect. Crystal oscillator interface. XTAL_IN is the input, XTAL_OUT is the output. Pullup Output enable pin for Q2/nQ2 outputs. Logic High, outputs are enabled. Logic LOW, outputs are in Hi-Z. LVCMOS/LVTTL interface levels. 16, 17, 22, 30 GND Power Power supply ground. 20, 21 nQ2, Q2 Output Differential output pair. M-LVDS interface levels. 25, 26 nQ1, Q1 Output Differential output pair. M-LVDS interface levels. 28 VDDA Power Analog supply pin. 29 OE1 Input 31, 32 nQ0, Q0 Output Pullup Output enable pin for Q1/nQ1 outputs. Logic High, outputs are enabled. Logic LOW, outputs are in Hi-Z. LVCMOS/LVTTL interface levels. Differential output pair. M-LVDS interface levels. NOTE: Pullup and Pulldown refer to internal input resistors. See Table 2, Pin Characteristics, for typical values. Table 2. Pin Characteristics Symbol Parameter CIN Input Capacitance 4 pF RPULLUP Input Pullup Resistor 51 kΩ RPULLDOWN Input Pulldown Resistor 51 kΩ IDT™ / ICS™ M-LVDS CLOCK SYNTHESIZER Test Conditions 2 Minimum Typical Maximum Units ICS845204AK SEPTEMBER 25, 2007 ICS845204 CRYSTAL-TO-MLVDS CLOCK SYNTHESIZER W/SPREAD SPECTRUM ADVANCE INFORMATION Function Tables Table 3A. F_SEL[1:0] Function Table Inputs Table 3B. SSC[1:0] Function Table Outputs Inputs Spread% FSEL1 FSEL0 Q[0:3]/nQ[0:3] SSC1 SSC0 0 0 PLL Bypass (25MHz) 0 0 Center ± -0.25 0 1 100MHz (default) 0 1 Down -0.5 1 0 125MHz 1 0 Down -0.75 1 1 250MHz 1 1 No Spread (default) Absolute Maximum Ratings NOTE: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only. Functional operation of product at these conditions or any conditions beyond those listed in the DC Characteristics or AC Characteristics is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. Item Rating Supply Voltage, VDD 4.6V Inputs, VI -0.5V to VDD + 0.5V Outputs, IO Continuos Current Surge Current 10mA 15mA Package Thermal Impedance, θJA 42.4°C/W (0 mps) Storage Temperature, TSTG -65°C to 150°C DC Electrical Characteristics Table 4A. Power Supply DC Characteristics, VDD = VDDO = 3.3V ± 5%, TA = 0°C to 70°C Symbol Parameter VDD Core Supply Voltage VDDA Minimum Typical Maximum Units 3.135 3.3 3.465 V Analog Supply Voltage VDD – IDDA*10Ω 3.3 VDD V VDDO Output Supply Voltage 3.135 3.3 3.465 V IDD Power Supply Current TBD mA IDDA Analog Supply Current TBD mA IDDO Power Supply Current TBD mA IDT™ / ICS™ M-LVDS CLOCK SYNTHESIZER Test Conditions 3 ICS845204AK SEPTEMBER 25, 2007 ICS845204 CRYSTAL-TO-MLVDS CLOCK SYNTHESIZER W/SPREAD SPECTRUM ADVANCE INFORMATION Table 4B. LVCMOS/LVTTL DC Characteristics, VDD = VDDO = 3.3V ± 5%, TA = 0°C to 70°C Symbol Parameter Test Conditions VIH Input High Voltage VIL Input Low Voltage IIH Input High Current IIL Input Low Current Minimum Typical Maximum Units 2 VDD + 0.3 V -0.3 0.8 V F_SEL1 VDD = VIN = 3.465V 150 µA SSC0, SSC1, FSEL0, OE0:OE3 VDD = VIN = 3.465V 5 µA F_SEL1 VDD = 3.465V, VIN = 0V -5 µA SSC0, SSC1, FSEL0, OE0:OE3 VDD = 3.465V, VIN = 0V -150 µA Table 4C. M-LVDS DC Characteristics, VDD = VDDO = 3.3V ± 5%, TA = 0°C to 70°C Symbol Parameter VOD Differential Output Voltage ∆VOD VOD Magnitude Change VOS Offset Voltage ∆VOS VOS Magnitude Change ISC Output Short Circuit Current Test Conditions Minimum Typical 480 Maximum Units 650 mV 50 0.30 mV 2.10 50 V mV 43 mA Table 5. Crystal Characteristics Parameter Test Conditions Mode of Oscillation Minimum Typical Maximum Units Fundamental Frequency 25 MHz Equivalent Series Resistance (ESR) 50 Ω Shunt Capacitance 7 pF TBD mW Drive Level IDT™ / ICS™ M-LVDS CLOCK SYNTHESIZER 4 ICS845204AK SEPTEMBER 25, 2007 ICS845204 CRYSTAL-TO-MLVDS CLOCK SYNTHESIZER W/SPREAD SPECTRUM ADVANCE INFORMATION AC Electrical Characteristics Table 6. AC Characteristics, VDD = VDDO = 3.3V ± 5%, TA = 0°C to 70° Parameter Symbol fOUT tjit(per) Test Conditions Minimum Output Frequency Period Jitter, Random tjit(cc) Cycle-to-Cycle Jitter; NOTE 1, 2 tsk(o) Output Skew; NOTE 2, 3 FXTAL Typical Maximum Units 25 MHz 100 MHz 125 MHz 25MHz, Integration Range: 12kHz – 20MHz TBD ps 100MHz, Integration Range: 12kHz – 20MHz TBD ps 125MHz, Integration Range: 12kHz – 20MHz TBD ps 250MHz, Integration Range: 12kHz – 20MHz TBD ps 25MHz 50 ps 100MHz 50 ps 125MHz 50 ps 50 ps 250MHz TBD ps Crystal Input Range: NOTE 1 25 MHz FM SSC Modulation Frequency; NOTE 4 TBD kHz FMF SSC Modulation Factor; NOTE 4 TBD % SSCRED Spectral Reduction TBD dB tSTABLE Power-up Stable Clock Output tR / tF Output Rise/Fall Time odc Output Duty Cycle 10 20% to 80% ms TBD ps 50 % NOTE 1: This parameter is defined in accordance with JEDEC Standard 65. NOTE 2: Only valid within the VCO operating range. NOTE 3: Defined as skew between outputs at the same supply voltage and with equal load conditions. Measured at the output differential cross points. NOTE 4: Spread Spectrum clocking enabled. IDT™ / ICS™ M-LVDS CLOCK SYNTHESIZER 5 ICS845204AK SEPTEMBER 25, 2007 ICS845204 CRYSTAL-TO-MLVDS CLOCK SYNTHESIZER W/SPREAD SPECTRUM ADVANCE INFORMATION Parameter Measurement Information VOH VREF SCOPE 3.3V±5% POWER SUPPLY + Float GND – Qx VDD, VDDO VDDA M-LVDS VOL 1σ contains 68.26% of all measurements 2σ contains 95.4% of all measurements 3σ contains 99.73% of all measurements 4σ contains 99.99366% of all measurements 6σ contains (100-1.973x10-7)% of all measurements nQx Histogram Reference Point Mean Period (Trigger Edge) (First edge after trigger) - - Period Jitter nQx nQx Qx Qx ➤ nQy ➤ 3.3V LVDS Output Load AC Test Circuit ➤ tcycle n tcycle n+1 ➤ tjit(cc) = tcycle n – tcycle n+1 1000 Cycles Qy tsk(o) Output Skew Cycle-to-Cycle Jitter nQ0:nQ3 80% Q0:Q3 80% t PW VOD Clock Outputs t PERIOD 20% 20% tR tF odc = t PW x 100% t PERIOD Output Duty Cycle/Pulse Width/Period Output Rise/Fall Time IDT™ / ICS™ M-LVDS CLOCK SYNTHESIZER 6 ICS845204AK SEPTEMBER 25, 2007 ICS845204 CRYSTAL-TO-MLVDS CLOCK SYNTHESIZER W/SPREAD SPECTRUM ADVANCE INFORMATION Parameter Measurement Information, continued VDD VDD out M-LVDS ➤ out ➤ out DC Input ➤ M-LVDS 100 100 ➤ VOD/∆ VOD VOS/∆ VOS out ➤ DC Input ➤ Offset Voltage Setup Differential Output Voltage Setup Application Information Power Supply Filtering Technique As in any high speed analog circuitry, the power supply pins are vulnerable to random noise. The ICS845204 provides separate power supplies to isolate any high switching noise from the outputs to the internal PLL. VDD, VDDA and VDDO should be individually connected to the power supply plane through vias, and bypass capacitors should be used for each pin. To achieve optimum jitter performance, power supply isolation is required. Figure 1 illustrates how a 10Ω resistor along with a 10µF and a 0.01µF bypass capacitor should be connected to each VDDA pin. 3.3V VDD .01µF 10Ω .01µF 10µF VDDA Figure 1. Power Supply Filtering Recommendations for Unused Input and Output Pins Inputs: Outputs: LVCMOS Control Pins M-LVDS Outputs All control pins have internal pull-ups or pull-downs; additional resistance is not required but can be added for additional protection. A 1kΩ resistor can be used. All unused M-LVDS output pairs can be either left floating or terminated with 100Ω across. If they are left floating, there should be no trace attached. IDT™ / ICS™ M-LVDS CLOCK SYNTHESIZER 7 ICS845204AK SEPTEMBER 25, 2007 ICS845204 CRYSTAL-TO-MLVDS CLOCK SYNTHESIZER W/SPREAD SPECTRUM ADVANCE INFORMATION Crystal Input Interface The ICS845204 has been characterized with 18pF parallel resonant crystals. The capacitor values, C1 and C2, shown in Figure 2 below were determined using a 25MHz, 18pF parallel resonant crystal and were chosen to minimize the ppm error. The optimum C1 and C2 values can be slightly adjusted for different board layouts. XTAL_IN C1 X1 18pF Parallel Crystal XTAL_OUT C2 Figure 2. Crystal Input Interface LVCMOS to XTAL Interface The XTAL_IN input can accept a single-ended LVCMOS signal through an AC coupling capacitor. A general interface diagram is shown in Figure 3. The XTAL_OUT pin can be left floating. The input edge rate can be as slow as 10ns. For LVCMOS inputs, it is recommended that the amplitude be reduced from full swing to half swing in order to prevent signal interference with the power rail and to reduce noise. This configuration requires that the output VDD impedance of the driver (Ro) plus the series resistance (Rs) equals the transmission line impedance. In addition, matched termination at the crystal input will attenuate the signal in half. This can be done in one of two ways. First, R1 and R2 in parallel should equal the transmission line impedance. For most 50Ω applications, R1 and R2 can be 100Ω. This can also be accomplished by removing R1 and making R2 50Ω. VDD R1 Ro Rs 0.1µf 50Ω XTAL_IN Zo = Ro + Rs R2 XTAL_OUT Figure 3. General Diagram for LVCMOS Driver to XTAL Input Interface IDT™ / ICS™ M-LVDS CLOCK SYNTHESIZER 8 ICS845204AK SEPTEMBER 25, 2007 ICS845204 CRYSTAL-TO-MLVDS CLOCK SYNTHESIZER W/SPREAD SPECTRUM ADVANCE INFORMATION VFQFN EPAD Thermal Release Path In order to maximize both the removal of heat from the package and the electrical performance, a land pattern must be incorporated on the Printed Circuit Board (PCB) within the footprint of the package corresponding to the exposed metal pad or exposed heat slug on the package, as shown in Figure 4. The solderable area on the PCB, as defined by the solder mask, should be at least the same size/shape as the exposed pad/slug area on the package to maximize the thermal/electrical performance. Sufficient clearance should be designed on the PCB between the outer edges of the land pattern and the inner edges of pad pattern for the leads to avoid any shorts. application specific and dependent upon the package power dissipation as well as electrical conductivity requirements. Thus, thermal and electrical analysis and/or testing are recommended to determine the minimum number needed. Maximum thermal and electrical performance is achieved when an array of vias is incorporated in the land pattern. It is recommended to use as many vias connected to ground as possible. It is also recommended that the via diameter should be 12 to 13mils (0.30 to 0.33mm) with 1oz copper via barrel plating. This is desirable to avoid any solder wicking inside the via during the soldering process which may result in voids in solder between the exposed pad/slug and the thermal land. Precautions should be taken to eliminate any solder voids between the exposed heat slug and the land pattern. Note: These recommendations are to be used as a guideline only. For further information, please refer to the Application Note on the Surface Mount Assembly of Amkor’s Thermally/Electrically Enhance Leadfame Base Package, Amkor Technology. While the land pattern on the PCB provides a means of heat transfer and electrical grounding from the package to the board through a solder joint, thermal vias are necessary to effectively conduct from the surface of the PCB to the ground plane(s). The land pattern must be connected to ground through these vias. The vias act as “heat pipes”. The number of vias (i.e. “heat pipes”) are PIN PIN PAD SOLDER EXPOSED HEAT SLUG GROUND PLANE THERMAL VIA SOLDER LAND PATTERN (GROUND PAD) PIN PIN PAD Figure 4. P.C. Assembly for Exposed Pad Thermal Release Path – Side View (drawing not to scale) IDT™ / ICS™ M-LVDS CLOCK SYNTHESIZER 9 ICS845204AK SEPTEMBER 25, 2007 ICS845204 CRYSTAL-TO-MLVDS CLOCK SYNTHESIZER W/SPREAD SPECTRUM ADVANCE INFORMATION 3.3V M-LVDS Driver Termination A general M-LVDS interface is shown in Figure 5 In a 100Ω differential transmission line environment, M-LVDS drivers require a matched load termination of 100Ω across near the receiver input. For a multiple M-LVDS outputs buffer, if only partial outputs are used, it is recommended to terminate the unused outputs. 3.3V 50Ω 3.3V LVDS Driver + R2 100Ω R1 100Ω – 50Ω 100Ω Differential Transmission Line Figure 5. Typical M-LVDS Driver Termination Reliability Information Table 7. θJA vs. Air Flow Table for a 32Lead VFQFN θJA vs. Air Flow Meters per Second Multi-Layer PCB, JEDEC Standard Test Boards 0 1 2.5 42.4°C/W 37.0°C/W 33.2°C/W Transistor Count The transistor count for ICS845204 is: 3749 IDT™ / ICS™ M-LVDS CLOCK SYNTHESIZER 10 ICS845204AK SEPTEMBER 25, 2007 ICS845204 CRYSTAL-TO-MLVDS CLOCK SYNTHESIZER W/SPREAD SPECTRUM ADVANCE INFORMATION Package Outline and Package Dimension Package Outline - K Suffix for 32 Lead VFQFN (Ref.) S eating Plan e N &N Even (N -1)x e (R ef.) A1 Ind ex Area A3 N L N e (Ty p.) 2 If N & N 1 Anvil Singula tion are Even 2 OR E2 (N -1)x e (Re f.) E2 2 To p View b A (Ref.) D Chamfer 4x 0.6 x 0.6 max OPTIONAL e N &N Odd 0. 08 C D2 2 Th er mal Ba se D2 C NOTE: The following package mechanical drawing is a generic drawing that applies to any pin count VFQFN package. This drawing is not intended to convey the actual pin count or pin layout of this device. The pin count and pinout are shown on the front page. The package dimensions are in Table 8 below. Table 8. Package Dimensions JEDEC Variation: VHHD-2/-4 All Dimensions in Millimeters Symbol Minimum Nominal Maximum N 32 A 0.80 1.00 A1 0 0.05 A3 0.25 Ref. b 0.18 0.25 0.30 8 ND & NE D&E 5.00 Basic D2 & E2 3.0 3.3 e 0.50 Basic L 0.30 0.40 0.50 Reference Document: JEDEC Publication 95, MO-220 IDT™ / ICS™ M-LVDS CLOCK SYNTHESIZER 11 ICS845204AK SEPTEMBER 25, 2007 ICS845204 CRYSTAL-TO-MLVDS CLOCK SYNTHESIZER W/SPREAD SPECTRUM ADVANCE INFORMATION Ordering Information Table 9. Ordering Information Part/Order Number 845204AK 845204AKT 845204AKLF 845204AKLFT Marking TBD TBD ICS845204AL ICS845204AL Package 32 Lead VFQFN 32 Lead VFQFN “Lead-Free” 32 Lead VFQFN “Lead-Free” 32 Lead VFQFN Shipping Packaging Tray 2500 Tape & Reel Tray 2500 Tape & Reel Temperature 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C NOTE: Parts that are ordered with an "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications, such as those requiring extended temperature ranges, high reliability or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. IDT™ / ICS™ M-LVDS CLOCK SYNTHESIZER 12 ICS845204AK SEPTEMBER 25, 2007 ICS845204 CRYSTAL-TO-MLVDS CLOCK SYNTHESIZER W/SPREAD SPECTRUM ADVANCE INFORMATION Innovate with IDT and accelerate your future networks. Contact: www.IDT.com www.IDT.com For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 [email protected] 480-763-2056 Corporate Headquarters Asia Pacific and Japan Europe Integrated Device Technology, Inc. 6024 Silver Creek Valley Road San Jose, CA 95138 United States 800 345 7015 +408 284 8200 (outside U.S.) Integrated Device Technology Singapore (1997) Pte. Ltd. Reg. No. 199707558G 435 Orchard Road #20-03 Wisma Atria Singapore 238877 +65 6 887 5505 IDT Europe, Limited 321 Kingston Road Leatherhead, Surrey KT22 7TU England +44 (0) 1372 363 339 Fax: +44 (0) 1372 378851 © 2007 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA