Integrated Circuit Systems, Inc. ICS9250-19 Frequency Generator & Integrated Buffers for Celeron & PII/III™ Recommended Application: BX, Appollo Pro 133 type of chip set. Output Features: • 3 - CPUs @2.5V, up to 150MHz. • 17 - SDRAM @ 3.3V, up to 150MHz. • 7 - PCI @3.3V • 2 - IOAPIC @ 2.5V • 1 - 48MHz, @3.3V fixed. • 1 - 24MHz @ 3.3V • 2 - REF @3.3V, 14.318MHz. Features: • Up to 150MHz frequency support • Support power management: CPU, PCI, stop and Power down Mode form I2C programming. • Spread spectrum for EMI control (0 to -0.5%, ± 0.25%). • Uses external 14.318MHz crystal Key Specifications: • CPU – CPU: <175ps • CPU – PCI: 1 - 4ns • PCI – PCI: <500ps • SDRAM - SDRAM: <250ps Pin Configuration 56-Pin SSOP Block Diagram * Internal Pull-up Resistor of 240K to 3.3V on indicated inputs ** Internal Pull-down resistor of 240K to GND on indicated inputs. Functionality 9250-19 Rev C 4/12/01 Third party brands and names are the property of their respective owners. FS3 FS2 FS1 FS0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 CPU (MHz) 133 124 150 140 105 110 115 120 100.0 133 112 103 66.6 83.3 75 124 PCICLK (MHz) 33.3 (CPU/4) 31 (CPU/4) 37.5 (CPU/4) 35 (CPU/4) 35 (CPU/3) 36.67 (CPU/3) 38.33 (CPU/3) 40.00 (CPU/3) 33.43 (CPU/3) 44.33 (CPU/3) 37.33 (CPU/3) 34.33 (CPU/2) 33.40 (CPU/2) 41.65 (CPU/2) 37.5 (CPU/2) 41.33 (CPU/2) ICS reserves the right to make changes in the device data identified in this publication without further notice. ICS advises its customers to obtain the latest version of all device data to verify that any information being relied upon by the customer is current and accurate. ICS9250-19 Pin Configuration PIN NUMBER 2 3 P I N NA M E REF1 FS21 REF0 P C I _ S TO P # 4, 10, 23, 26, 34, 42, GND 48, 53 TYPE OUT IN OUT IN PWR 5 X1 IN 6 X2 OUT PCICLK_F OUT 8 9 16, 14, 13, 12, 11 17 27 28 MODE1 IN FS3 IN DESCRIPTION 14.318 MHz reference clock output L a t c h e d f r e q u e n cy s e l e c t i n p u t . H a s p u l l - u p t o V D D P C I 14.318MHz reference clock output Halts PCICLK [5:1] at logic "0" level when low. (in mobile, MODE=0) Ground. 14.318MHz input. Has internal load cap, (nominal 33pF). Crystal output. Has internal load cap (33pF) and feedback resistor to X1 F r e e r u n n i n g B U S c l o c k n o t a f e c t e d b y P C I _ S TO P # Latched input for MODE select. Converts pin 3 to PCI_STOP# when low for power management. Latched frequency select input, pull-down PCICLK0 OUT F r e e r u n n i n g B U S c l o c k n o t a f e c t e d b y P C I _ S TO P # PCICLK [5:1] OUT PCI Clock Outputs. BU F F E R I N SDATA SCLK 24MHz IN IN IN Input for Buffers Serial data in for serial config port. (I2C) Clock input for serial config port. (I2C) OUT 24MHz clock output for Super I/O or FD. 30 FS01 IN L a t c h e d f r e q u e n cy s e l e c t i n p u t . H a s p u l l - u p t o V D D 4 . OUT IN 48MHz clock output for USB. L a t c h e d f r e q u e n cy s e l e c t i n p u t . H a s p u l l - u p t o V D D 2 . PWR Nominal 3.3V power supply, see power groups for function. SDRAM [15:0] OUT SDRAM clocks 46 SDRAM_F OUT Free running SDRAM clock Not affected by CPU_STOP# 47 C P U _ S TO P # 29 1, 7, 15, 20, 31, 37, 45 24, 25, 32, 33, 18, 19, 21, 22, 35, 36, 38, 39, 40, 41, 43, 44 50, 56 55 51, 49 52 54 48MHz FS11 VDDPCI, VDDREF, VDDSDR, VDD48 VDDLCPU, VDDLIOAPIC I OA P I C 0 CPUCLK [2:1] CPUCLK_F I OA P I C _ F IN Halts CPUCLK [2:1], IOAPIC0, SDRAM [15:0] clocks at logic "0" level when low. PWR CPU and IOAPIC clock buffer power supply, 2.5V nominal. OUT OUT OUT IOAPIC clock output. (14.318 MHz) Poweredby VDDL1 CPU Output clocks. Powered by VDDL2 (60 or 66.6MHz) Free running CPU output clock. Not affected ty the CPU_STOP#. Freerunning IOAPIC clock output. Not affected by the CPU_STOP# (14.31818 MHz) Powered by VDDL1 OUT Notes: 1: Bidirectional input/output pins, input logic levels are latched at internal power-on-reset. Use 10Kohm resistor to program logic Hi to VDD or GND for logic low. Third party brands and names are the property of their respective owners. 2 ICS9250-19 General Description The ICS9250-19 is the single chip clock solution for Desktop/designs using BX, Appollo Pro 133 type of chip sets. It provides all necessary clock signals for such a system. Spread spectrum may be enabled through I2C programming. Spread spectrum typically reduces system EMI by 8dB to 10dB. This simplifies EMI qualification without resorting to board design iterations or costly shielding. The ICS9250-19 employs a proprietary closed loop design, which tightly controls the percentage of spreading over process and temperature variations. Serial programming I2C interface allows changing functions, stop clock programming and frequency selection. Mode Pin - Power Management Input Control MODE (Latched Input) 0 1 PCI_STOP# (Input) REF0 (Output) Third party brands and names are the property of their respective owners. 3 ICS9250-19 General I2C serial interface information The information in this section assumes familiarity with I2C programming. For more information, contact ICS for an I2C programming application note. How to Write: How to Read: • • • • • • • • • • • • • • • • Controller (host) sends a start bit. Controller (host) sends the write address D2 (H) ICS clock will acknowledge Controller (host) sends a dummy command code ICS clock will acknowledge Controller (host) sends a dummy byte count ICS clock will acknowledge Controller (host) starts sending first byte (Byte 0) through byte 5 • ICS clock will acknowledge each byte one at a time. • Controller (host) sends a Stop bit Controller (host) will send start bit. Controller (host) sends the read address D3 (H) ICS clock will acknowledge ICS clock will send the byte count Controller (host) acknowledges ICS clock sends first byte (Byte 0) through byte 5 Controller (host) will need to acknowledge each byte Controller (host) will send a stop bit How to Write: Controller (Host) Start Bit Address D2(H) ICS (Slave/Receiver) How to Read: Controller (Host) Start Bit Address D3(H) ACK Dummy Command Code ACK ICS (Slave/Receiver) ACK Byte Count Dummy Byte Count ACK ACK ACK ACK ACK ACK ACK ACK ACK ACK ACK ACK ACK ACK Stop Bit Byte 0 Byte 0 Byte 1 Byte 1 Byte 2 Byte 2 Byte 3 Byte 3 Byte 4 Byte 4 Byte 5 Byte 5 Stop Bit Notes: 1. 2. 3. 4. 5. 6. The ICS clock generator is a slave/receiver, I2C component. It can read back the data stored in the latches for verification. Read-Back will support Intel PIIX4 "Block-Read" protocol. The data transfer rate supported by this clock generator is 100K bits/sec or less (standard mode) The input is operating at 3.3V logic levels. The data byte format is 8 bit bytes. To simplify the clock generator I2C interface, the protocol is set to use only "Block-Writes" from the controller. The bytes must be accessed in sequential order from lowest to highest byte with the ability to stop after any complete byte has been transferred. The Command code and Byte count shown above must be sent, but the data is ignored for those two bytes. The data is loaded until a Stop sequence is issued. At power-on, all registers are set to a default condition, as shown. Third party brands and names are the property of their respective owners. 4 ICS9250-19 Serial Configuration Command Bitmap Byte0: Functionality and Frequency Select Register (default = 0) Bit Bit 7 Bit 2, Bit 6:4 Bit 3 Bit 1 Bit 0 Description 0 = 0 to -0.5% Down Spread Spectrum Modulation 1 = ±0.25% Center Spread Spectrum Modulation Bit2 Bit6 Bit5 Bit4 CPU clock PCI 0111 100.0 33.43 (CPU/3) 0110 133 44.33 (CPU/3) 0101 112 37.33 (CPU/3) 0100 103 34.3 (CPU/3) 0011 66.6 33.4 (CPU/2) 0010 83.3 41.65(CPU/2) 0001 75 37.5 (CPU/2) 0000 124 41.33 (CPU/3) 1111 133 33.25 (CPU/4) 1110 124 31.00 (CPU/4) 1101 150 37.50 (CPU/4) 1100 140 35.00 (CPU/4) 1011 105 35.00 (CPU/3) 1010 110 36.67 (CPU/3) 1001 115 38.33 (CPU/3) 1000 120 40.00 (CPU/3) 0 - Frequency is selected by hardware select, Latched Inputs 1 - Frequency is selected by Bit 6:4 (above) 0 - Normal 1 - Spread Spectrum Enabled (Center Spread) 0 - Running 1- Tristate all outputs PWD 0 Note1 0 1 0 Note 1. Default at Power-up will be for latched logic inputs to define frequency. Bits 4, 5, 6 are default to 000, and if bit 3 is written to a 1 to use Bits 6:4, then these should be defined to desired frequency at same write cycle. Note: PWD = Power-Up Default Third party brands and names are the property of their respective owners. 5 ICS9250-19 Byte 1: CPU, Active/Inactive Register (1= enable, 0 = disable) BIT Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PIN# 46 49 51 52 PWD 1 1 1 1 1 1 1 1 Byte 2: PCI, Active/Inactive Register (1= enable, 0 = disable) DESCRIPTION R e s e r ve d R e s e r ve d R e s e r ve d R e s e r ve d SDRAM_F (Act/Inact) CPUCLK2 (Act/Inact) CPUCLK1 (Act/Inact) CPUCLK_F (Act/Inact) BIT Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 3 Bit 2 Bit 1 Bit 0 PIN# 29 30 33, 32, 25, 24 22, 21, 19, 18 39, 38, 36, 35 44, 43, 41, 40 PWD 1 1 1 1 BIT PIN# PWD Bit 7 X Bit 6 1 Bit 5 1 Bit 4 X Bit 3 1 Bit 2 1 Bit 1 X Bit 0 1 DESCRIPTION R e s e r ve d R e s e r ve d 48MHz (Act/Inact) 24MHz (Act/Inact) 1 SDRAM(12:15) (Act/Inact) 1 SDRAM (8:11) (Act/Inact) 1 SDRAM (4:7) (Act/Inact) 1 SDRAM (0:3) (Act/Inact) PWD 1 1 1 1 1 1 1 1 DESCRIPTION R e s e r ve d PCICLKF (Act/Inact) PCICLK5 (Act/Inact) PCICLK4 (Act/Inact) PCICLK3 (Act/Inact) PCICLK2 (Act/Inact) PCICLK1 (Act/Inact) PCICLK0 (Act/Inact) Byte 4: Reserved , Active/Inactive Register (1= enable, 0 = disable) Byte 3: SDRAM, Active/Inactive Register (1= enable, 0 = disable) BIT Bit 7 Bit 6 Bit 5 Bit 4 PIN# 8 16 14 13 12 11 9 DESCRIPTION Latched FS0# R e s e r ve d R e s e r ve d Latched FS1# R e s e r ve d R e s e r ve d Latched FS3# R e s e r ve d Byte 5: Peripheral , Active/Inactive Register (1= enable, 0 = disable) BIT PIN# PWD Bit 7 1 Bit 6 X Bit 5 54 1 Bit 4 55 1 Bit 3 1 Bit 2 1 Bit 1 2 1 Bit 0 3 1 DESCRIPTION R e s e r ve d Latched FS2# IOAPIC_F (Act/Inact) IOAPIC0 (Act/Inact) R e s e r ve d R e s e r ve d REF1 (Act/Inact) REF0 (Act/Inact) Third party brands and names are the property of their respective owners. Notes: 1. Inactive means outputs are held LOW and are disabled from switching. 2. Latched Frequency Selects (FS#) will be inferted logic load of the input frequency select pin conditions. 6 ICS9250-19 Shared Pin Operation Input/Output Pins These figures illustrate the optimal PCB physical layout options. These configuration resistors are of such a large ohmic value that they do not effect the low impedance clock signals. The layouts have been optimized to provide as little impedance transition to the clock signal as possible, as it passes through the programming resistor pad(s). The I/O pins designated by (input/output) on the ICS925019 serve as dual signal functions to the device. During initial power-up, they act as input pins. The logic level (voltage) that is present on these pins at this time is read and stored into a 4-bit internal data latch. At the end of Power-On reset, (see AC characteristics for timing values), the device changes the mode of operations for these pins to an output function. In this mode the pins produce the specified buffered clocks to external loads. To program (load) the internal configuration register for these pins, a resistor is connected to either the VDD (logic 1) power supply or the GND (logic 0) voltage potential. A 10 Kilohm(10K) resistor is used to provide both the solid CMOS programming voltage needed during the power-up programming period and to provide an insignificant load on the output clock during the subsequent operating period. Figs. 1 and 2 show the recommended means of implementing this function. In Fig. 1 either one of the resistors is loaded onto the board (selective stuffing) to configure the device’s internal logic. Figs. 2a and b provide a single resistor loading option where either solder spot tabs or a physical jumper header may be used. Fig. 1 Third party brands and names are the property of their respective owners. 7 ICS9250-19 Fig. 2a Fig. 2b Third party brands and names are the property of their respective owners. 8 ICS9250-19 CPU_STOP# Timing Diagram CPUSTOP# is an asychronous input to the clock synthesizer. It is used to turn off the CPUCLKs for low power operation. CPU_STOP# is synchronized by the ICS9250-19. All other clocks will continue to run while the CPUCLKs are disabled. The CPUCLKs will always be stopped in a low state and start in such a manner that guarantees the high pulse width is a full pulse. CPUCLK on latency is less than 4 CPUCLKs and CPUCLK off latency is less than 4 CPUCLKs. Notes: 1. All timing is referenced to the internal CPUCLK. 2. CPU_STOP# is an asynchronous input and metastable conditions may exist. This signal is synchronized to the CPUCLKs inside the ICS9250-19. 3. IOAPIC output is stopped Glitch Free by CPUSTOP# going low. 4. PCI_STOP# is shown in a high (true) state. 5. All other clocks continue to run undisturbed. PCI_STOP# Timing Diagram PCI_STOP# is an asynchronous input to the ICS9250-19. It is used to turn off the PCICLK (0:5) clocks for low power operation. PCI_STOP# is synchronized by the ICS9250-19 internally. PCICLK (0:5) clocks are stopped in a low state and started with a full high pulse width guaranteed. PCICLK (0:5) clock on latency cycles are only one rising PCICLK clock off latency is one PCICLK clock. Notes: 1. All timing is referenced to the Internal CPUCLK (defined as inside the device.) 2. PCI_STOP# is an asynchronous input, and metastable conditions may exist. This signal is required to be synchronized inside the device. 3. All other clocks continue to run undisturbed. 4. CPU_STOP# is shown in a high (true) state. Third party brands and names are the property of their respective owners. 9 ICS9250-19 Absolute Maximum Ratings Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . Logic Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ambient Operating Temperature . . . . . . . . . . . . . Case Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . 5.5 V GND –0.5 V to VDD +0.5 V 0°C to +70°C 115°C –65°C to +150°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only and functional operation of the device at these or any other conditions above those listed in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. Electrical Characteristics - Input/Supply/Common Output Parameters TA = 0 - 70º C; Supply Voltage VDD = 3.3 V +/-5%, VDDL = 2.5 V +/-5% (unless otherwise stated) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Input High Voltage VIH 2 VDD+0.3 V Input Low Voltage VIL VSS-0.3 0.8 V VIN = VDD 0.1 5 Input High Current IIH µA Input Low Current IIL1 VIN = 0 V; Inputs with no pull-up resistors -5 2.0 µA Input Low Current IIL2 VIN = 0 V; Inputs with pull-up resistors -200 -100 µA Operating IDD3.3OP100 Select @ 100MHz; Sdram running 150 180 mA 200 Supply Current IDD3.3OP133 Select @ 133MHz; Sdram running n/a VDD = 3.3 V 12 14.318 16 MHz Input frequency Fi 1 Input Capacitance CIN Logic Inputs 5 pF X1 & X2 pins 27 36 45 pF CINX Transition Time1 TTrans To 1st crossing of target Freq. 4 ms Settling Time1 TS From 1st crossing to 1% target Freq. 1 3 ms Clk Stabilization1 TStab From VDD = 3.3 V to 1% target Freq. 4 ms 1 Guaranteed by design, not 100% tested in production. Electrical Characteristics - Input/Supply/Common Output Parameters TA = 0 - 70º C; Supply Voltage VDD = 3.3 V +/-5%, VDDL = 2.5 V +/-5% (unless otherwise stated) PARAMETER SYMBOL CONDITIONS MIN TYP Operating IDD2.5OP100 Select @ 100MHz; Max discrete cap loads 13 Select @ 133MHz; Max discrete cap loads I Supply Current 18 DD2.5OP133 1 Guaranteed by design, not 100% tested in production. Third party brands and names are the property of their respective owners. 10 MAX 25 25 UNITS mA ICS9250-19 Electrical Characteristics - CPUCLK TA = 0 - 70º C; VDD = 3.3 V +/-5%, VDDL = 2.5 V +/-5%; CL = 20 pF (unless otherwise stated) PARAMETER SYMBOL CONDITIONS MIN Output High Voltage VOH2B IOH = -12.0 mA 2 IOL = 12 mA Output Low Voltage VOL2B VOH = 1.7 V Output High Current IOH2B VOL = 0.7 V 19 Output Low Current IOL2B 1 Rise Time tr2B VOL = 0.4 V, VOH = 2.0 V 0.4 1 VOH = 2.0 V, VOL = 0.4 V 0.4 Fall Time tf2B Duty Cycle dt2B1 VT = 1.25 V 45 1 Skew group1: 1,2 and 1,F tsk2B VT = 1.25 V 1 Skew group2: 2, F tsk2B VT = 1.25 V VT = 1.25 V Jitter, One Sigma tj1σ2B1 1 VT = 1.25 V -250 Jitter, Absolute tjabs2B tjcyc-cyc2B1 VT = 1.25 V Jitter, Cycle-to-cycle TYP 2.3 0.2 -41 37 1 51 120 120 100 150 MAX 0.4 -19 1.6 1.6 55 175 295 250 +250 250 UNITS V V mA mA ns ns % ps ps ps ps ps 1 Guaranteed by design, not 100% tested in production. Electrical Characteristics - 48MHz, 24MHz,REF0 TA = 0 - 70º C; VDD = 3.3 V +/-5%, VDDL = 2.5 V +/-5%; CL = 20 pF (unless otherwise stated) PARAMETER Output High Voltage Output Low Voltage Output High Current Output Low Current IOH = -14 mA IOL = 6.0 mA VOH = 2.0 V VOL = 0.8 V MIN 2.4 10 TYP 2.9 0.25 -42 18 MAX 0.4 -20 UNITS V V mA mA tr5 VOL = 0.4 V, VOH = 2.4 V 1.1 2.5 ns 1 tf5 VOH = 2.4 V, VOL = 0.4 V 1 2.5 ns 50 100 250 55 250 800 % ps ps Duty Cycle Jitter1 Jitter1 1 CONDITIONS 1 Rise Time Fall Time SYMBOL VOH5 VOL5 IOH5 IOL5 1 dt5 tj1s5 tjabs5 VT = 1.5 V VT = 1.5 V, 24, 48MHz VT = 1.5 V, REF0 Guaranteed by design, not 100% tested in production. Third party brands and names are the property of their respective owners. 11 45 ICS9250-19 Electrical Characteristics - PCICLK T A = 0 - 70º C; V DD = 3.3 V +/-5%, V DDL = 2.5 V +/-5%; C L = 60 pF for PCI0 & PCI1, CL = 30 pF for other PCIs PA RA M ETER Output High Voltage Output Low Voltage Output High Current Output Low Current Ris e Time Fall Time 1 1 Duty Cycle Skew 1 1 Jitter, One Sigma Jitter, A bs olute 1 SYM BOL VO H 1 VO L 1 IO H 1 IO L 1 1 1 CONDITIONS IO H = -18 mA IO L = 9.4 mA VO H = 2.0 V VO L = 0.8 V M IN 2.4 25 TYP 2.9 0.2 -58 52 M A X UNITS V 0.4 V -22 mA mA t r1 VO L = 0.8 V, VO H = 2.4 V 1.5 2.5 ns t f1 VO H = 2.4 V, VO L = 0.4 V 1.4 2.5 ns d t1 VT = 1.5 V 50 55 % t sk 1 VT = 1.5 V 270 500 ps t j1 σ1 VT = 1.5 V 50 150 ps t jab s1 VT = 1.5 V 200 500 ps 45 Guaranteed by des ign, not 100% tes ted in production. Electrical Characteristics - SDRAM T A = 0 - 70º C; VDD = 3.3 V +/-5%, VDDL = 2.5 V +/-5%; C L =30 pF PA RA M ETER Output High Voltage Output Low Voltage Output High Current Output Low Current Ris e Time Fall Time SYM BOL VO H 1 VO L 1 IO H 1 IO L 1 1 1 Duty Cycle 1 1 Skew(Group1: F,0:4, 8:11) 1 Skew(Group2: 5, 7, 12:15) 1 Skew(Group3: 0, 13) 1 Skew(Group4: 6, 13) 1 Skew(Buferin-Output) Jitter, One Sigma Jitter, A bs olute 1 1 1 CONDITIONS IO H = -28 mA IO L = 19 mA VO H = 2.0 V VO L = 0.8 V M IN 2.4 33 TYP 2.8 0.34 -72 50 M A X UNITS V 0.4 V -42 mA mA t r1 VO L = 0.4 V, VO H = 2.4 V 0.5 2 ns t f1 VO H = 2.4 V, VO L = 04 V 0.5 2.4 ns d t1 VT = 1.5 V 45 50 55 % t sk 1 VT = 1.5 V 130 250 ps t sk 1 VT = 1.5 V 180 250 ps t sk 1 VT = 1.5 V 490 ps t sk 1 VT = 1.5 V 910 ps t sk 1 VT = 1.5 V 3.5 4.4 ns t j1 σ1 VT = 1.5 V 50 150 ps t jab s1 VT = 1.5 V 130 250 ps -250 Guaranteed by des ign, not 100% tes ted in production. Third party brands and names are the property of their respective owners. 12 ICS9250-19 Electrical Characteristics - IOAPIC TA = 0 - 70º C; VDD = 3.3 V +/-5%, VDDL = 2.5 V +/-5%; CL = 20 pF (unless otherwise stated) 1 PARAMETER Output High Voltage Output Low Voltage Output High Current Output Low Current SYMBOL VOH4B VOL4B IOH4B IOL4B Rise Time1 Tr4B Fall Time1 Duty Cycle1 Jitter, One Sigma1 Jitter, Absolute1 CONDITIONS 19 TYP 2.2 0.3 -32 26 VOL = 0.4 V, VOH = 2.0 V 0.4 1.5 1.8 ns Tf4B VOH = 2.0 V, VOL = 0.4 V 0.4 1 1.6 ns Dt4B VT = 1.25 V 45 51 55 % Tj1σ4B VT = 1.25 V 240 300 ps Tjabs4B VT = 1.25 V 619 650 ps IOH = -12 mA IOL = 12 mA VOH = 1.7 V VOL = 0.7 V Guaranteed by design, not 100% tested in production. Third party brands and names are the property of their respective owners. 13 MIN 2 MAX UNITS V 0.4 V -19 mA mA ICS9250-19 General Layout Precautions: 1) Use a ground plane on the top layer of the PCB in all areas not used by traces. Ferrite Bead VDD 2) Make all power traces and ground traces as wide as the via pad for lower inductance. Notes: 1) All clock outputs should have a series terminating resistor, and a 20pF capacitor to ground between the resistor and clock pin. Not shown in all places to improve readibility of diagram. 2) Optional crystal load capacitors are recommended. They should be included in the layout but not inserted unless needed. C2 22µF/20V Tantalum C2 22µF/20V Tantalum 1 56 2 55 3 54 4 53 5 52 6 51 7 50 8 49 9 48 10 47 Ferrite Bead VDD C3 C1 2.5V Power Route 1 C1 2 Clock Load C3 3.3V Power Route 11 46 12 45 13 44 14 43 15 42 16 41 17 40 18 39 19 38 20 37 21 36 22 35 23 34 24 33 25 32 26 31 27 30 28 29 3.3V Power Route Component Values: C1 : Crystal load values determined by user C2 : 22 F/20V/D case/Tantalum AVX TAJD226M020R C3 : 100pF ceramic capacitor C4 : 20pF capacitor FB = Fair-Rite products 2512066017X1 All unmarked capacitors are 0.01 F ceramic Connections to VDD: Ground Ground = Routed Power = Ground Connection (component side copper) = Ground Plane Connection = Power Route Connection = Solder Pads = Clock Load Third party brands and names are the property of their respective owners. 14 ICS9250-19 c N SYMBOL L E1 INDEX AREA E 1 2 h x 45° D A A A1 b c D E E1 e h L N α A1 -Ce SEATING PLANE b .10 (.004) C N 56 In Millimeters COMMON DIMENSIONS MIN MAX 2.41 2.80 0.20 0.40 0.20 0.34 0.13 0.25 SEE VARIATIONS 10.03 10.68 7.40 7.60 0.635 BASIC 0.38 0.64 0.50 1.02 SEE VARIATIONS 0° 8° In Inches COMMON DIMENSIONS MIN MAX .095 .110 .008 .016 .008 .0135 .005 .010 SEE VARIATIONS .395 .420 .291 .299 0.025 BASIC .015 .025 .020 .040 SEE VARIATIONS 0° 8° VARIATIONS D mm. MIN MAX 18.31 18.55 D (inch) MIN .720 MAX .730 Reference Doc.: JEDEC Publication 95, MO-118 10-0034 300 mil SSOP Package Ordering Information ICS9250yF-19 Example: ICS XXXX y F - PPP Pattern Number (2 or 3 digit number for parts with ROM code patterns) Package Type F=SSOP Revision Designator (will not correlate with datasheet revision) Device Type Prefix ICS, AV = Standard Device Third party brands and names are the property of their respective owners. 15 ICS reserves the right to make changes in the device data identified in this publication without further notice. ICS advises its customers to obtain the latest version of all device data to verify that any information being relied upon by the customer is current and accurate.