Impala Linear Corporation ILC7011 Preliminary 80mA SC70 Ultra Low Noise CMOS RF-LDO™ Regulator General Description Features The ILC7011 is an 80mA, Ultra Low Noise, Low Dropout (LDO) linear regulator, designed and processed in Impala’s proprietary CMOS process technology. This process combines the best CMOS features of low quiescent current, small size and low dropout voltage with the best bipolar features of high ripple rejection, ultra low noise and power handling capability. The ILC7011 offers a quiescent current of less than 100µA, a logic level enable (regulator on/off) pin, a footprint that is half the size of the industry standard SOT23 and a low dropout voltage of 50mV at 10mA. With better than 70dB (1kHz) of ripple rejection, ultra low noise of 10µVRMS and 1% output voltage accuracy, the ILC7011 sets a new standard in linear regulators for communications and personal electronics applications. • 1% output voltage accuracy • Only 10µVRMS noise from 300Hz to 100kHz • Uses low ESR ceramic or Tantalum output capacitor to minimize noise and output ripple. • Only 90µA ground current at 80mA load • Ripple rejection up to 70dB at 1kHz, 60dB at 1MHz • Excellent line and load transient response • Guaranteed to 80mA output current • Industry standard five lead SC70 packages • Fixed 2.8V, 3.0V, 3.3V, 3.6V, 4.7V, 5.0V, output voltage options • Metal mask option available for custom voltages between 2.5V and 8V The ILC7011 is designed to operate with small, low cost, ceramic capacitors and is stable over a wide range of ESR values. In addition to the output capacitor, the ILC7011 requires only a 1µF input capacitor. The enable pin can be tied to VIN for easy device layout. The ILC7011 is available in a number of fixed output voltages ranging from 2.5V to 8V. An adjacent version will be available shortly. • • • • Applications Cellular phones Wireless communicators PDAs / palmtops / organizers Battery powered portable electronics The ILC7011 is ideally suited for use in small size cordless and cellular handsets as well as many other low battery powered electronic devices. Please contact Impala for samples and application information. Typical Circuit 4 5 CNOISE Ordering Information ON (TA = 0°C to 70°C) OFF ILC7011C5-XX ILC7011 VOUT 1 2 COUT Impala Linear Corporation ILC7011 1.4 80mA, fixed voltage, SC-70 Package VIN 3 Note: Fixed voltage options are defined by 2-digit code as shown in the package markings information section of the data sheet CIN (408) 574-3939 www.impalalinear.com August 2000 1 80mA SC 70 Ultra Low Noise CMOS RF-LDO™ Regulator Preliminary Pin Description ILC7011 (fixed voltage version) Pin Number Pin Name Pin Description 4 ON/OFF 5 CNOISE 2 GND Ground pin. Local ground for COUT 1 VOUT Output voltage. Connect COUT between this pin and the GND (pin 3) 2 VIN By applying less than 0.4V to this pin the device will be turned off Noise Bypass Capacitor Connect Directly to Supply Pin Package Configurations ON OFF CNOISE 4 5 ILC7011 Parameter 1 2 3 VOUT GND VIN Symbol Ratings Units VIN -0.3 to +9V V VON/OFF -0.3 to VIN V Output Current IOUT Short Circuit Protected mA Output Voltage VOUT -0.3 to VIN +0.3 V PD TBD mW TJ(MAX) -40 to +125 °C Storage Temperature TSTG -40 to +125 °C Operation Ambient Temperature TSTG -40 to +125 °C Input Voltage 7011 ON/OFF Input Voltage Package Power Dissipation Maximum Juncion Temp. Range Impala Linear Corporation ILC7011 1.4 (408) 574-3939 www.impalalinear.com August 2000 2 80mA SC 70 Ultra Low Noise CMOS RF-LDO™ Regulator Preliminary Electrical Characteristics ILC7011 Unless otherwise specified all limits are at TA = 25°C, VIN = VOUT (NOM) + 1V, IOUT = 1mA, COUT = 1mF, VON/OFF = 2V Parameter Input Voltage Range Symbol VIN Conditions Output Voltage Accuracy Line Regulation Dropout Voltage (Note 3) Ground Pin Current Shutdown (OFF) Current ∆VOUT/(VOUT*∆VIN) VOUT (NOM) + 1V < 8V IOUT = 10µA IOUT = 10mA VIN VOUT IOUT = 20mA IOUT = 80mA IOUT = 0mA IGND IOUT = 10mA IOUT = 80mA ION/OFF ION/OFF = 0V ON/OFF Input Voltage VON/OFF High = Regulator On Low = Regulator Off ON/OFF Pin Input Current (Note 5) IIN ON/OFF V V Peak Output Current (Note 4) IOUT (peak) VOUT > 0.95V Output Noise Voltage eN Ripple Rejection ∆VOUT/∆VIN Units V ±1 % %/V 0.007 0.1 50 70 235 66 67 90 0.6V Regulator OFF ON/OFF 2V Regulator ON ON/OFF OUT (NOM), tpw Typ 2.5-8 = 2ms BW = 300Hz to 50kHz, CIN = 1µF CNOISE = 0.01µF, COUT = 1.0µF, IOUT = 10mA COUT = 4.7µF Tantalum IOUT = 80mA Freq = 1kHz Freq = 10kHz Freq = 1MHz mV µA 0.1 µA 1.5-2.0 0.6 V 0.3 1 µA 100-120 mA TBD µVrms 70 50 65 dB Dynamic Line Regulation ∆VOUT(line) VIN: VOUT (NOM) + 1V to VOUT (NOM) + 2V, tr/tf = 2µs; IOUT = 80mA 14 mV Dynamic Load Regulation ∆VOUT(load) IOUT: 1mA to 80mA; tr < 5µS 40 mV VOUT = 0V 200 mA 1.5 kΩ Short Circuit Current ISC Resistance Shutdown Discharge Note 1: Absolute maximum ratings indicate limits which when exceeded may result in damage to the component. Electrical specifications do not apply when operating the device outside of its rated operating conditions. Note 2: Specified Min/Max limits are production tested or guaranteed through correlation based on statistical control methods. Measurments are taken at constant junction temperature as close to ambient as possible using low duty pulse testing. Note 3 Dropout voltage is defined as the input to output differential voltage at which the output voltage drops 2% below the nominal value measured with a 1V differential. Note 4: Guaranteed by design Note 5: The device’s shutdown pin inlcudes a 2MΩ internal pull down resistor connected to ground. Impala Linear Corporation ILC7011 1.4 (408) 574-3939 www.impalalinear.com August 2000 3 80mA SC 70 Ultra Low Noise CMOS RF-LDO™ Regulator Preliminary SC-70 Package Markings ILC7011C5-xx Output Voltage (V) Grade Order Information Supplied As: 2.8 A ILC7011C5-28 3K Units on Tape and Reel 3.0 A ILC7011C5-30 3K Units on Tape and Reel 3.3 A ILC7011C5-33 3K Units on Tape and Reel 3.6 A ILC7011C5-36 3K Units on Tape and Reel 4.7 A ILC7011C5-47 3K Units on Tape and Reel 5.0 A ILC7011C5-50 3K Units on Tape and Reel *NOTE: First two characters identify the product and the last two characters identify the datecode .45 .70 .325 1.85 c 1.15/1.35 .325 .65 1.30 Recommended Mount Pad 0.15-0.30 0.65 BSC .65 0.65 BSC This product is intended for use in normal commercial applications. Applications requiring an extended temperature range, unusual environmental requirements, or high reliability applications, such as military and aerospace, are specifically not recommended without additional processing by Impala Linear Corporation. 0.10-0.18 0.02 Devices sold by Impala Linear Corporation are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Impala Linear Corporation makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. Impala Linear Corporation makes no warranty of merchantability or fitness for any purpose. Impala Linear Corporation reserves the right to discontinue production and change specifications and prices at any time and without notice. x 0.45-0.60 0.80-1.00 0.78-0.98 1.80-2.20 1.30 15° Life Support Policy Impala Linear Corporation’s products are not authorized for use as critical components in life support devices or systems. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labelling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonbly expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Impala Linear Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in an Impala Linear Corporation product. No other circuits, patents, licenses are implied. Impala Linear Corporation ILC7011 1.4 (408) 574-3939 www.impalalinear.com August 2000 4