IS62WV51216ALL IS62WV51216BLL ISSI ® 512K x 16 LOW VOLTAGE, ULTRA LOW POWER CMOS STATIC RAM FEBRUARY 2005 FEATURES DESCRIPTION • High-speed access time: 45ns, 55ns The ISSI IS62WV51216ALL/ IS62WV51216BLL are highspeed, 8M bit static RAMs organized as 512K words by 16 bits. It is fabricated using ISSI's high-performance CMOS technology. This highly reliable process coupled with innovative circuit design techniques, yields highperformance and low power consumption devices. • CMOS low power operation – 36 mW (typical) operating – 12 µW (typical) CMOS standby When CS1 is HIGH (deselected) or when CS2 is LOW (deselected) or when CS1 is LOW, CS2 is HIGH and both LB and UB are HIGH, the device assumes a standby mode at which the power dissipation can be reduced down with CMOS input levels. • TTL compatible interface levels • Single power supply – 1.65V--2.2V VDD (62WV51216ALL) – 2.5V--3.6V VDD (62WV51216BLL) Easy memory expansion is provided by using Chip Enable and Output Enable inputs. The active LOW Write Enable (WE) controls both writing and reading of the memory. A data byte allows Upper Byte (UB) and Lower Byte (LB) access. • Fully static operation: no clock or refresh required • Three state outputs • Data control for upper and lower bytes The IS62WV51216ALL and IS62WV51216BLL are packaged in the JEDEC standard 48-pin mini BGA (7.2mm x 8.7mm) and 44-Pin TSOP (TYPE II). • Industrial temperature available • Lead-free available FUNCTIONAL BLOCK DIAGRAM A0-A18 DECODER 512K x 16 MEMORY ARRAY I/O DATA CIRCUIT COLUMN I/O VDD GND I/O0-I/O7 Lower Byte I/O8-I/O15 Upper Byte CS2 CS1 OE WE UB LB CONTROL CIRCUIT Copyright © 2005 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. B 02/24/05 1 ISSI IS62WV51216ALL, IS62WV51216BLL PIN CONFIGURATIONS PIN DESCRIPTIONS 48-Pin mini BGA (7.2mm x 8.7mm) 1 2 3 4 5 6 A0-A18 Address Inputs I/O0-I/O15 Data Inputs/Outputs CS1, CS2 Chip Enable Input OE Output Enable Input WE Write Enable Input A LB OE A0 A1 A2 CS2 LB Lower-byte Control (I/O0-I/O7) B I/O8 UB A3 A4 CS1 I/O0 UB Upper-byte Control (I/O8-I/O15) C I/O9 I/O10 A5 A6 I/O1 I/O2 NC No Connection D GND I/O11 A17 A7 I/O3 VDD` VDD Power E VDD I/O12 GND A16 I/O4 GND GND Ground F I/O14 I/O13 A14 A15 I/O5 I/O6 G I/O15 NC A12 A13 WE I/O7 H A18 A9 A10 A11 NC A8 ® 44-Pin TSOP (Type II) A4 A3 A2 A1 A0 CS1 I/O0 I/O1 I/O2 I/O3 VDD GND I/O4 I/O5 I/O6 I/O7 WE A16 A15 A14 A13 A12 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 A5 A6 A7 OE UB LB I/O15 I/O14 I/O13 I/O12 GND VDD I/O11 I/O10 I/O9 I/O8 A18 A8 A9 A10 A11 A17 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. B 02/24/05 ISSI IS62WV51216ALL, IS62WV51216BLL ® TRUTH TABLE I/O PIN I/O0-I/O7 I/O8-I/O15 WE CS1 CS2 OE LB UB Not Selected X X X H X X X L X X X X X X H X X H High-Z High-Z High-Z High-Z High-Z High-Z ISB1, ISB2 ISB1, ISB2 ISB1, ISB2 Output Disabled H H L L H H H H L X X L High-Z High-Z High-Z High-Z ICC I CC Read H H H L L L H H H L L L L H L H L L DOUT High-Z DOUT High-Z DOUT DOUT I CC Write L L L L L L H H H X X X L H L H L L DIN High-Z DIN High-Z DIN DIN I CC Mode VDD Current OPERATING RANGE (VDD) Range Ambient Temperature IS62WV51216ALL (70ns) IS62WV51216BLL (55ns, 70ns) Commercial Industrial 0°C to +70°C 1.65V - 2.2V 2.5V - 3.6V –40°C to +85°C 1.65V - 2.2V 2.5V - 3.6V Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. B 02/24/05 IS62WV51216BLL (45ns) 3.0 - 3.6V 3 ISSI IS62WV51216ALL, IS62WV51216BLL ® ABSOLUTE MAXIMUM RATINGS(1) Symbol VTERM TBIAS VDD TSTG PT Parameter Terminal Voltage with Respect to GND Temperature Under Bias VDD Related to GND Storage Temperature Power Dissipation Value –0.2 to VDD+0.3 –40 to +85 –0.2 to +3.8 –65 to +150 1.0 Unit V °C V °C W Note: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC ELECTRICAL CHARACTERISTICS (Over Operating Range) Symbol Parameter Test Conditions VDD Min. Max. Unit VOH Output HIGH Voltage IOH = -0.1 mA IOH = -1 mA 1.65-2.2V 2.5-3.6V 1.4 2.2 — — V V VOL Output LOW Voltage IOL = 0.1 mA IOL = 2.1 mA 1.65-2.2V 2.5-3.6V — — 0.2 0.4 V V VIH Input HIGH Voltage 1.65-2.2V 2.5-3.6V 1.4 2.2 VDD + 0.2 VDD + 0.3 V V VIL(1) Input LOW Voltage 1.65-2.2V 2.5-3.6V –0.2 –0.2 0.4 0.6 V V ILI Input Leakage GND ≤ VIN ≤ VDD –1 1 µA ILO Output Leakage GND ≤ VOUT ≤ VDD, Outputs Disabled –1 1 µA Notes: 1. VIL (min.) = –1.0V for pulse width less than 10 ns. 4 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. B 02/24/05 ISSI IS62WV51216ALL, IS62WV51216BLL ® CAPACITANCE(1) Symbol Parameter CIN Input Capacitance COUT Input/Output Capacitance Conditions Max. Unit VIN = 0V 8 pF VOUT = 0V 10 pF Note: 1. Tested initially and after any design or process changes that may affect these parameters. AC TEST CONDITIONS Parameter Input Pulse Level Input Rise and Fall Times Input and Output Timing and Reference Level Output Load 62WV51216ALL (Unit) 0.4V to VDD-0.2 5 ns VREF 62WV51216BLL (Unit) 0.4V to VDD-0.3V 5ns VREF See Figures 1 and 2 See Figures 1 and 2 62WV51216ALL (1.65V - 2.2V) 62WV51216BLL (2.5V - 3.6V) R1(Ω) 3070 1029 R2(Ω) 3150 1728 VREF 0.9V 1.5V VTM 1.8V 2.8V AC TEST LOADS R1 R1 VTM VTM OUTPUT OUTPUT 30 pF Including jig and scope R2 Figure 1 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. B 02/24/05 5 pF Including jig and scope R2 Figure 2 5 ISSI IS62WV51216ALL, IS62WV51216BLL ® IS62WV51216ALL, POWER SUPPLY CHARACTERISTICS(1) (Over Operating Range) Symbol ICC ICC1 ISB1 Parameter Test Conditions VDD Dynamic Operating Supply Current Operating Supply Current VDD = Max., IOUT = 0 mA, f = fMAX VDD = Max., CS1 = 0.2V WE = VDD – 0.2V CS2 = VDD – 0.2V, f = 1MHZ VDD = Max., VIN = VIH or VIL CS1 = VIH , CS2 = VIL, f = 1 MHZ TTL Standby Current (TTL Inputs) Unit Com. Ind. Com. Ind. Max. 70 20 25 4 4 Com. Ind. 0.3 0.3 mA 15 21 3 µA mA mA OR ULB Control ISB2 CMOS Standby Current (CMOS Inputs) VDD = Max., VIN = VIH or VIL CS1 = VIL, f = 0, UB = VIH, LB = VIH VDD = Max., Com. CS1 ≥ VDD – 0.2V, Ind. CS2 ≤ 0.2V, typ.(1) VIN ≥ VDD – 0.2V, or VIN ≤ 0.2V, f = 0 OR ULB Control VDD = Max., CS1 = VIL, CS2=VIH VIN ≥ VDD – 0.2V, or VIN ≤ 0.2V, f = 0; UB / LB = VDD – 0.2V Note:. 1. Typical values are measured at VDD = 1.8V, TA = 25oC and not 100% tested. 6 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. B 02/24/05 ISSI IS62WV51216ALL, IS62WV51216BLL ® IS62WV51216BLL, POWER SUPPLY CHARACTERISTICS(1) (Over Operating Range) Symbol ICC ICC1 ISB1 Parameter Test Conditions VDD Dynamic Operating Supply Current Operating Supply Current VDD = Max., IOUT = 0 mA, f = fMAX VDD = Max., CS1 = 0.2V WE = VDD – 0.2V CS2 = VDD – 0.2V, f = 1MHZ VDD = Max., VIN = VIH or VIL CS1 = VIH , CS2 = VIL, f = 1 MHZ TTL Standby Current (TTL Inputs) Max. 55 30 35 5 5 Max. 70 25 30 5 5 Unit Com. Ind. Com. Ind. Max. 45 35 40 5 5 Com. Ind. 0.3 0.3 0.3 0.3 0.3 0.3 mA 20 25 4 20 25 4 20 25 4 µA mA mA OR ULB Control ISB2 CMOS Standby Current (CMOS Inputs) VDD = Max., VIN = VIH or VIL CS1 = VIL, f = 0, UB = VIH, LB = VIH VDD = Max., Com. CS1 ≥ VDD – 0.2V, Ind. CS2 ≤ 0.2V, typ. (2) VIN ≥ VDD – 0.2V, or VIN ≤ 0.2V, f = 0 OR ULB Control VDD = Max., CS1 = VIL, CS2=VIH VIN ≥ VDD – 0.2V, or VIN ≤ 0.2V, f = 0; UB / LB = VDD – 0.2V Note: 1. At f = fMAX, address and data inputs are cycling at the maximum frequency, f = 0 means no input lines change. 2. Typical values are measured at VDD = 3.0V, TA = 25oC and not 100% tested. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. B 02/24/05 7 ISSI IS62WV51216ALL, IS62WV51216BLL ® READ CYCLE SWITCHING CHARACTERISTICS(1) (Over Operating Range) Symbol Parameter 45 ns Min. Max. 55 ns Min. Max. 70 ns Min. Max. Unit tRC Read Cycle Time 45 — 55 — 70 — ns tAA Address Access Time — 45 — 55 — 70 ns tOHA Output Hold Time 10 — 10 — 10 — ns tACS1/tACS2 CS1/CS2 Access Time — 45 — 55 — 70 ns tDOE OE Access Time — 20 — 25 — 35 ns (2) OE to High-Z Output — 15 — 20 — 25 ns (2) tLZOE OE to Low-Z Output 5 — 5 — 5 — ns tHZCS1/tHZCS2(2) CS1/CS2 to High-Z Output 0 15 0 20 0 25 ns tLZCS1/tLZCS2(2) CS1/CS2 to Low-Z Output 10 — 10 — 10 — ns tBA LB, UB Access Time — 45 — 55 — 70 ns tHZB LB, UB to High-Z Output 0 15 0 20 0 25 ns tLZB LB, UB to Low-Z Output 0 — 0 — 0 — ns tHZOE Notes: 1. Test conditions assume signal transition times of 5 ns or less, timing reference levels of 0.9V/1.5V, input pulse levels of 0.4 to VDD-0.2V/0.4V to VDD-0.3V and output loading specified in Figure 1. 2. Tested with the load in Figure 2. Transition is measured ±500 mV from steady-state voltage. Not 100% tested. AC WAVEFORMS READ CYCLE NO. 1(1,2) (Address Controlled) (CS1 = OE = VIL, CS2 = WE = VIH, UB or LB = VIL) tRC ADDRESS tAA tOHA DQ0-D15 8 PREVIOUS DATA VALID tOHA DATA VALID Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. B 02/24/05 ISSI IS62WV51216ALL, IS62WV51216BLL ® AC WAVEFORMS READ CYCLE NO. 2(1,3) (CS1, CS2, OE, AND UB/LB Controlled) tRC ADDRESS tAA tOHA OE tDOE CS1s tHZOE tLZOE tACE1/tACE2 CS2s tLZCE1/ tLZCE2 tHZCS1/ tHZCS1 LBs, UBs tBA tHZB tLZB DOUT HIGH-Z DATA VALID Notes: 1. WE is HIGH for a Read Cycle. 2. The device is continuously selected. OE, CS1, UB, or LB = VIL. CS2=WE=VIH. 3. Address is valid prior to or coincident with CS1 LOW transition. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. B 02/24/05 9 ISSI IS62WV51216ALL, IS62WV51216BLL ® WRITE CYCLE SWITCHING CHARACTERISTICS(1,2) (Over Operating Range) Symbol tWC 45ns Min. Max. Parameter Write Cycle Time tSCS1/tSCS2 CS1/CS2 to Write End tAW Address Setup Time to Write End 55 ns Min. Max. 70 ns Min. Max. Unit 45 — 55 — 70 — ns 35 — 45 — 60 — ns 35 — 45 — 60 — ns tHA tSA Address Hold from Write End 0 — 0 — 0 — ns Address Setup Time 0 — 0 — 0 — ns tPWB tPWE(4) LB, UB Valid to End of Write 35 — 45 — 60 — ns WE Pulse Width 35 — 40 — 50 — ns tSD tHD Data Setup to Write End 20 — 25 — 30 — ns Data Hold from Write End 0 — 0 — 0 — ns tHZWE(3) tLZWE(3) WE LOW to High-Z Output — 20 — 20 — 30 ns WE HIGH to Low-Z Output 5 — 5 — 5 — ns Notes: 1. Test conditions assume signal transition times of 5 ns or less, timing reference levels of 0.9V/1.5V, input pulse levels of 0.4 to VDD-0.2V/0.4V to VDD-0.3V and output loading specified in Figure 1. 2. The internal write time is defined by the overlap of CS1 LOW, CS2 HIGH and UB or LB, and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the write. 3. Tested with the load in Figure 2. Transition is measured ±500 mV from steady-state voltage. Not 100% tested. 4. tPWE > tHZWE + tSD when OE is LOW. AC WAVEFORMS WRITE CYCLE NO. 1(1,2) (CS1 Controlled, OE = HIGH or LOW) tWC ADDRESS tHA tSCS1 CS1 tSCS2 CS2 tAW tPWE WE tPWB LB, UB tSA DOUT tHZWE DATA UNDEFINED tLZWE HIGH-Z tSD DIN tHD DATA-IN VALID Notes: 1. WRITE is an internally generated signal asserted during an overlap of the LOW states on the CS1 , CS2 and WE inputs and at least one of the LB and UB inputs being in the LOW state. 2. WRITE = (CS1) [ (LB) = (UB) ] (WE). 10 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. B 02/24/05 ISSI IS62WV51216ALL, IS62WV51216BLL ® WRITE CYCLE NO. 2 (WE Controlled: OE is HIGH During Write Cycle) tWC ADDRESS OE tHA tSCS1 CS1 tSCS2 CS2 tAW t PWE WE LB, UB tSA DOUT tHZWE tLZWE HIGH-Z DATA UNDEFINED tSD DIN tHD DATA-IN VALID WRITE CYCLE NO. 3 (WE Controlled: OE is LOW During Write Cycle) tWC ADDRESS OE tHA tSCS1 CS1 tSCS2 CS2 tAW t PWE WE LB, UB tSA DOUT DATA UNDEFINED tHZWE tLZWE HIGH-Z tSD DIN Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. B 02/24/05 tHD DATA-IN VALID 11 ISSI IS62WV51216ALL, IS62WV51216BLL ® WRITE CYCLE NO. 4 (UB/LB Controlled) t WC ADDRESS t WC ADDRESS 1 ADDRESS 2 OE t SA CS1 LOW CS2 HIGH t HA t SA WE UB, LB t HA t PBW t PBW WORD 1 WORD 2 t HZWE DOUT t LZWE HIGH-Z DATA UNDEFINED t HD t SD DIN DATAIN VALID t HD t SD DATAIN VALID UB_CSWR4.eps 12 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. B 02/24/05 ISSI IS62WV51216ALL, IS62WV51216BLL ® DATA RETENTION SWITCHING CHARACTERISTICS Symbol Parameter Test Condition Min. Max. Unit VDR VDD for Data Retention See Data Retention Waveform 1.2 3.6 V IDR Data Retention Current VDD = 1.2V, CS1 ≥ VDD – 0.2V — 20 µA tSDR tRDR Data Retention Setup Time See Data Retention Waveform 0 — ns Recovery Time See Data Retention Waveform tRC — ns DATA RETENTION WAVEFORM (CS1 Controlled) Data Retention Mode tSDR tRDR VDD 1.65V 1.4V VDR CS1 ≥ VDD - 0.2V CS1 GND DATA RETENTION WAVEFORM (CS2 Controlled) Data Retention Mode 3.0 VDD CE2 2.2V tSDR tRDR VDR 0.4V CS2 ≤ 0.2V GND Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. B 02/24/05 13 ISSI IS62WV51216ALL, IS62WV51216BLL ® ORDERING INFORMATION IS62WV51216ALL (1.65V - 2.2V) Industrial Range: –40°C to +85°C Speed (ns) 70 Order Part No. Package IS62WV51216ALL-70TI TSOP-II IS62WV51216ALL-70BI mini BGA (7.2mm x 8.7mm) IS62WV51216ALL-70XI DIE Order Part No. Package IS62WV51216BLL-45B mini BGA (7.2mm x 8.7mm) ORDERING INFORMATION IS62WV51216BLL (2.5V - 3.6V) Commercial Range: 0°C to +70°C Speed (ns) 45 Industrial Range: –40°C to +85°C Speed (ns) 55 70 14 Order Part No. Package IS62WV51216BLL-55TI TSOP-II IS62WV51216BLL-55TLI TSOP-II, Lead-free IS62WV51216BLL-55BI mini BGA (7.2mm x 8.7mm) IS62WV51216BLL-55BLI mini BGA (7.2mm x 8.7mm), Lead-free IS62WV51216BLL-70XI DIE Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. B 02/24/05 ISSI IS62WV51216ALL, IS62WV51216BLL ® Mini Ball Grid Array Package Code: B (48-pin) Top View Bottom View φ b (48x) 1 2 3 4 5 6 6 A 4 3 2 1 A e B B C C D D D 5 D1 E E F F G G H H e E E1 A2 A A1 SEATING PLANE Notes: 1. Controlling dimensions are in millimeters. mBGA - 7.2mm x 8.7mm MILLIMETERS INCHES Sym. Min. Typ. Max. Min. Typ. Max. N0. Leads 48 A — — 1.20 — — 0.047 A1 0 .24 — 0.30 0.009 — 0.012 A2 0.60 — — 0.024 — — D 8.60 8.70 8.80 0.339 0.343 0.346 7.30 0.280 0.283 0.287 D1 E 5.25BSC 7.10 7.20 0.207BSC E1 3.75BSC 0.148BSC e 0.75BSC 0.030BSC b 0.30 0.35 0.40 0.012 0.014 0.016 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. B 02/24/05 15 ISSI ® PACKAGING INFORMATION Plastic TSOP Package Code: T (Type II) N N/2+1 E1 1 Notes: 1. Controlling dimension: millimieters, unless otherwise specified. 2. BSC = Basic lead spacing between centers. 3. Dimensions D and E1 do not include mold flash protrusions and should be measured from the bottom of the package. 4. Formed leads shall be planar with respect to one another within 0.004 inches at the seating plane. E N/2 D SEATING PLANE A ZD . b e Symbol Ref. Std. No. Leads A A1 b C D E1 E e L ZD α Millimeters Min Max Inches Min Max (N) 32 — 1.20 — 0.047 0.05 0.15 0.002 0.006 0.30 0.52 0.012 0.020 0.12 0.21 0.005 0.008 20.82 21.08 0.820 0.830 10.03 10.29 0.391 0.400 11.56 11.96 0.451 0.466 1.27 BSC 0.050 BSC 0.40 0.60 0.016 0.024 0.95 REF 0.037 REF 0° 5° 0° 5° L α A1 Plastic TSOP (T - Type II) Millimeters Inches Min Max Min Max 44 — 1.20 — 0.047 0.05 0.15 0.002 0.006 0.30 0.45 0.012 0.018 0.12 0.21 0.005 0.008 18.31 18.52 0.721 0.729 10.03 10.29 0.395 0.405 11.56 11.96 0.455 0.471 0.80 BSC 0.032 BSC 0.41 0.60 0.016 0.024 0.81 REF 0.032 REF 0° 5° 0° 5° Millimeters Min Max C Inches Min Max 50 — 1.20 0.05 0.15 0.30 0.45 0.12 0.21 20.82 21.08 10.03 10.29 11.56 11.96 0.80 BSC 0.40 0.60 0.88 REF 0° 5° — 0.047 0.002 0.006 0.012 0.018 0.005 0.008 0.820 0.830 0.395 0.405 0.455 0.471 0.031 BSC 0.016 0.024 0.035 REF 0° 5° Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. F 06/18/03