ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC Description Features World’s smallest 2.5 mm x 2.5 mm CDMA The ITM1010 is an integrated receiver front-end IC for 800 MHz Cellular CDMA and receiver chip 450MHz Operating frequency: CDMA450 mobile phones. The device has an LNA and a down-converter on a single die. Its low CDMA Cellular : 869 ~ 894 MHz noise amplifier and mixer have high linearity and CDMA 450 : 460 ~ 470 MHz high gain. The LNA has two-step gain control High linearity and high gain scheme, increasing dynamic range while saving Two step LNA gain control current. Gain, noise figure, and linearity of the 16 dB Gain, 1.2 dB NF, 9.5 dBm IIP3 LNA mixer can be easily adjusted using an external Adjustable Gain, NF, IIP3 of mixer using inductor. an external inductor The ITM1010 is fabricated on an advanced SiGe All pins are ESD-protected BiCMOS process which facilitates low -noise, low- Tiny 12-pin LPCC package (2.5mm × 2.5mm × 0.9mm) power, high-frequency analog circuits along with (LPCC) package, which is the smallest CDMA receiver chip in the world. Applications LNAE 10 LNAIN 11 MIXIN Functional Block Diagram MIXE pin 2.5mm x 2.5mm Leadless Plastic Chip Carrier LNAOUT CMOS control function. The ITM1010 uses tiny 12- 9 8 7 ITM1010 6 IFP 5 IFN Cellular CDMA/CDMA450 Mobile Phone (@ IS-95A/B/C, CDMA2000, CDMA20001X) 450 MHz CDMA Receiver Gain Control Bias Control 1 2 3 LOIN 4 VCC ENABLE Portable Radio Handset and Equipments GND 12 LNAGAIN 800 MHz CDMA and TDMA Receivers Ordering Information Part Package ITM1010 12-pin 2.5mmx2.5mm LPCC ITM1010TR ITM1010 Tape and Reel ITM1010EV ITM1010 Evaluation Board (800MHz) ITM1010EV45 ITM1010 Evaluation Board (450MHz) Integrant Technologies Inc. D-206, Bundang Technopark 151, Yatab-dong, Bundang-Gu, Seongnam-Si, Kyeongki-do 463-760, KOREA Tel : 82-31-719-4500, Fax. : 82-31-719-4506 For pricing, delivery, and ordering information, please contact [email protected] or visit www.integrant.biz . 02-IM1010-030827 [email protected] Tel: 82-31-719-4500 1/19 ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC 1. Operating Conditions 1-1 Absolute Maximum Ratings The ratings described below are stress-only, and the device’s performance might be degraded and/or permanent damage might be caused by the stresses applied beyond these ratings. Table 1-1 Absolute Maximum Ratings Parameter Symbol Min Max Unit Supply Voltage VCC -0.5 3.6 V Digital Input Voltage to Ground VD -0.3 Vcc+0.3 V 6 dBm 150 °C Input Power Level PImax Storage Temperature TS -40 Junction Temperature TJ 150 °C Lead Temperature (Soldering, 10sec) TL 240 °C 1-2 Recommended Operating Conditions All device performance of ITM1010 is guaranteed under these Recommended Operating Conditions. Table 1-2 Recommended Operation Conditions Parameter Symbol Min Max Unit Supply Voltage VCC 2.7 3.15 V Operating Temperature TA -40 85 °C Logic High Level Input Voltage VIH 1.8 Logic Low Level Input Voltage VIL V 0.4 V 1-3 Typical Current Consumption Table 1-3 Typical Current Consumption Parameter Cellular CDMA Power Down Current Typical Unit High Gain 28 mA Low Gain 19 mA <1 µA Note: Typical current consumption is measured at 25°C and Vcc=2.85V 1-4 Electrical Mode Table 1-4 Operation Mode Control Table ENA LNA_GAIN Operation Mode 0 X Full Power Down 1 0 LNA low gain 1 1 LNA high gain 02-IM1010-030827 [email protected] Tel: 82-31-719-4500 2/19 ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC 2. RF Specifications 2-1 CDMA LNA Table 2-1 CDMA LNA RF Specifications 1 Specification RF Frequency Range Min Typ 869 Max Unit 894 MHz Input VSWR 2:1 Output VSWR 2:1 Comments High Gain Mode Gain 15 Noise Figure Input IP3 16 dB 1.2 8.5 1.5 dB 9.5 dBm Gain -3.5 dB Noise Figure 4.8 dB Input IP3 23 dBm Low Gain Mode 2-2 CDMA Downconverter Table 2-2 CDMA Downconverter Specifications 1 Specification Min Typ RF Frequency Range 869 IF Frequency Range 50 85.38 Gain 8.5 9.5 Noise Figure IIP3 Output Impedance LO Power Unit 894 MHz 300 MHz 10.5 dB 10 dBm 1000 Ohm -7 dBm Input VSWR 2:1 Output VSWR 2:1 LO to RF Isolation 25 dB LO to IF Isolation 35 dB RF to LO Isolation 26 dB 02-IM1010-030827 Comments dB 9.5 8.7 Max [email protected] Tel: 82-31-719-4500 3/19 ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC 2-3 CDMA Cascaded Performance Table 2-3 CDMA Cascaded Specifications 1,2 Specification Min RF Frequency Range 869 IF Frequency Range 50 Typ 85.38 Max Unit 894 MHz 300 MHz Gain 23.5 dB Noise Figure 2.15 dB IIP3 -4.2 dBm IF Output Impedance 1000 Ohm -7 dBm LO Level Input VSWR 2:1 Output VSWR 2:1 Comments Notes 1. 2. The measurement condition is TA =25°C and VCC =3V with mixer emitter degeneration inductor (L4 in Fig. 4-1) of 8.2 nH (default value). Filter noise figure of 2.0dB is used for calculation of cascaded performance. 02-IM1010-030827 [email protected] Tel: 82-31-719-4500 4/19 ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC 2-4 CDMA450 LNA Table 2-4 450MHz CDMA LNA RF Specifications 3 Specification RF Frequency Range Min Typ 400 Max Unit 500 MHz Input VSWR 2:1 Output VSWR 2:1 Comments High Gain Mode Gain 15.5 Noise Figure Input IP3 16.5 1.6 8.5 dB 1.9 dB 9.5 dBm Gain -3.5 dB Noise Figure 3.3 dB Input IP3 25 dBm Low Gain Mode 2-5 CDMA450 Downconverter Table 2-5 450MHz CDMA Downconverter Specifications 3 Specification Min Typ RF Frequency Range 460 IF Frequency Range 50 85.38 Gain 9.5 10.5 Noise Figure IIP3 8.5 5.7 Output Impedance LO Power Max Unit 470 MHz 300 MHz dB 10 dB 7 dBm 1000 Ohm -10 dBm Input VSWR 2:1 Output VSWR 2:1 LO to RF Isolation 25 dB LO to IF Isolation 35 dB RF to LO Isolation 26 dB 02-IM1010-030827 Comments [email protected] Tel: 82-31-719-4500 5/19 ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC 2-6 CDMA450 Cascaded Performance Table 2-6 450MHz CDMA Cascaded Specifications 3,4 Specification Min RF Frequency Range 460 IF Frequency Range 50 Typ 85.38 Max Unit 470 MHz 300 MHz Gain 25 dB Noise Figure 2.2 dB IIP3 -7.6 dBm IF Output Impedance 1000 Ohm -10 dBm LO Level Input VSWR 2:1 Output VSWR 2:1 Comments Notes 3. 4. The measurement condition is TA =25°C and VCC =2.85V with mixer emitter degeneration inductor (L4 in Fig. 4-2) of 18 nH (default value). Filter noise figure of 2.0dB is used for calculation of cascaded performance. 02-IM1010-030827 [email protected] Tel: 82-31-719-4500 6/19 ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC 3. Typical Operating Characteristics ▶ CDMA450 CEL LG Current vs. Vcc CEL HG Current vs. Vcc 18.0 28.0 27.5 Current (mA) Current (mA) 17.5 17.0 -40 ℃ 25 ℃ 85 ℃ 16.5 27.0 26.5 26.0 -40 ℃ 25 ℃ 85 ℃ 25.5 16.0 25.0 2.7 2.8 2.9 3.0 3.1 3.2 2.7 2.8 Vcc (V) 3.0 3.1 3.2 Vcc (V) LNA High Gain vs. Vcc LNA Low Gain vs. Vcc 18.0 -2.0 17.5 -2.5 17.0 -3.0 Gain (dB) Gain (dB) 2.9 16.5 16.0 -40 ℃ 25 ℃ 85 ℃ 15.5 -3.5 -4.0 -40 ℃ 25 ℃ 85 ℃ -4.5 15.0 -5.0 2.7 2.8 2.9 3.0 3.1 3.2 2.7 2.8 Vcc (V) 2.9 3.0 3.1 3.2 Vcc (V) LNA HG-Mode IIP3 vs. Vcc LNA LG-Mode IIP3 vs. Vcc 10 26 25 IIP3 (dBm) IIP3 (dBm) 9 8 24 -40 ℃ 25 ℃ 85 ℃ 23 -40 ℃ 25 ℃ 85 ℃ 7 22 2.7 2.8 2.9 3.0 3.1 3.2 Vcc (V) 02-IM1010-030827 2.7 2.8 2.9 3.0 3.1 3.2 Vcc (V) [email protected] Tel: 82-31-719-4500 7/19 ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC 3. Typical Operating Characteristics(Cont’d) ▶ CDMA450 LNA HG-Mode NF vs. Vcc LNA LG-Mode NF vs. Vcc 3.0 5 2.5 4 2.0 NF (dB) NF (dB) 3 1.5 2 1.0 -40 ℃ 25 ℃ 85 ℃ 0.5 -40 ℃ 25 ℃ 85 ℃ 1 0.0 0 2.7 2.8 2.9 3.0 3.1 3.2 2.7 2.8 Vcc (V) 2.9 3.0 3.1 3.2 Vcc (V) Mixer Gain vs. Vcc Mixer IIP3 vs. Vcc 14 8 12 IIP3 (dBm) Gain (dB) 6 10 4 o -45 C -40 ℃ 25 ℃ 85 ℃ 8 o 25 C o 85 C 6 2 2.7 2.8 2.9 3.0 3.1 3.2 2.7 2.8 Vcc (V) Mixer NF vs. Vcc 3.0 3.1 3.2 Mixer Gain vs. LO Power 10 14 9 12 Gain (dB) NF (dB) 2.9 Vcc (V) 8 10 -40 ℃ 25 ℃ 85 ℃ 7 -40 ℃ 25 ℃ 85 ℃ 8 6 6 2.7 2.8 2.9 3.0 3.1 3.2 Vcc (V) 02-IM1010-030827 -25 -20 -15 -10 -5 0 LO Power (dBm) [email protected] Tel: 82-31-719-4500 8/19 ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC 3. Typical Operating Characteristics(Cont’d) ▶ CDMA450 Mixer NF vs. LO Power 12 7 10 NF (dB) IIP3 (dBm) Mixer IIP3 vs. LO Power 8 6 5 8 -40 ℃ 25 ℃ 85 ℃ 6 -40 ℃ 25 ℃ 85 ℃ 4 4 -25 -20 -15 -10 -5 0 LO Power (dBm) 02-IM1010-030827 -25 -20 -15 -10 -5 0 LO Power (dBm) [email protected] Tel: 82-31-719-4500 9/19 ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC 4. PIN Assignment Table 4-1 PIN Assignment Table PIN Symbol Description 1 LNA_GAIN LNA Gain Control Pin. With LNA_GAIN=HIGH, LNA operates at high-gain mode, and with LNA_GAIN=LOW LNA operates at low-gain mode. 2 ENA Enable Pin. If ENA is LOW, the device operates at full power-down mode. If ENA is HIGH the device operates at active mode. 3 LO_IN 4 VCC Power supply voltage 5 IFN Negative mixer output (open collector) 6 IFP Positive mixer output (open collector) 7 MIX_IN Mixer RF input 8 MIX_E Mixer emitter degeneration 9 LNA_OUT 10 LNA_ E LNA emitter degeneration 11 LNA_IN LNA RF input. Requires external matching network. 12 GND 02-IM1010-030827 Mixer LO input LNA output (open collector). Requires external matching network. Ground [email protected] Tel: 82-31-719-4500 10/19 ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC 5. Evaluation Board Schematic 5-1. CDMA Cellular Band(869 ~ 894 MHz) SAW_FILTER C1 2pF C5 4pF L8 12nH L4 8.2nH L5 6.8nH C4 47nF VCC LNA_E MIX_IN 7 9 10 MIX_E R5 0 ohm 8 VCC C8 100pF LNA_OUT C9 1nF L6 220nH IFP 6 ITM1010 C3 6pF C7 8pF 1 1 LNA_IN 5 LNA_GAIN VCC 3 LO_IN GND 2 12 1 C6 47 nF 4 R1 12 SAW_FILTER IF + C14 5pF C13 5pF L7 220nH Bias Control ENA Gain Control L3 10nH LNA_GAIN J4 2 1 3 IFN R2 30k C21 1nF IF C22 1nF VCC VCC C11 100pF L2 27nH ENA C20 5pF 1 3 2 Fig. 5-1 Evaluation Board Schematic for CDMA Cellular Application 02-IM1010-030827 [email protected] Tel: 82-31-719-4500 11/19 ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC 5-2. CDMA450 Band(460 ~ 470 MHz) SAW_FILTER C1 2pF C5 5pF L8 39nH L4 18nH L5 15nH C4 47nF VCC 10 LNA_E MIX_IN 7 9 MIX_E L9 3.3nH 8 VCC C8 100pF LNA_OUT C9 1nF L6 220nH IFP 6 ITM1010 C3 6pF C7 6pF 1 1 LNA_IN 5 VCC 3 LO_IN ENA GND L7 220nH Bias Control 2 12 1 C6 47 nF LNA_GAIN 3 1 2 Gain Control L3 22nH SAW_FILTER IF + C14 5pF R2 6.2k C 1 3 5pF IFN J4 C21 1nF IF C22 1nF VCC 4 VCC C11 100pF L2 82nH LNA_GAIN ENA 1 C20 4pF 3 2 Fig. 5-2 Evaluation Board Schematic for CDMA450 Application 02-IM1010-030827 [email protected] Tel: 82-31-719-4500 12/19 ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC 6. External Components 6-1. CDMA cellular application The external components below are used in the ITM1010 Evaluation Board, as shown in Fig. 5-1, for 800MHz CDMA cellular application. Table 5-1 External Component Information for CDMA cellular application Component Model Type Part Number C1 Murata, 2 pF 0402 C3 Murata, 6 pF 0402 C4 Murata, 47 nF 0402 C5 Murata, 4 pF 0402 C6 Murata, 47 nF 0402 C7 Murata, 8 pF 0402 C8 Murata, 100 pF 0402 C9 Murata, 1 nF 0402 C11 Murata, 100 pF 0402 C13 Murata, 5 pF 0402 C14 Murata, 5 pF 0402 C20 Murata, 100 pF 0402 C21 Murata, 1 nF 0402 C22 Murata, 1 nF 0402 L2 Toko, 27 nH 0402 L3 Toko, 10 nH 0402 L4 Toko, 6.8 nH 0402 L5 Toko, 6.8 nH 0402 L6 Coil Craft, 220 nH 0603 L7 Coil Craft, 220 nH 0603 L8 Toko, 12 nH 0402 R1 0402 12 Ω R2 0402 6.8 kΩ R5 0402 0Ω 02-IM1010-030827 [email protected] Tel: 82-31-719-4500 Comment 13/19 ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC 6-2. CDMA450 application The external components below are used in the ITM1010 Evaluation Board, as shown in Fig. 5-2, for 450MHz CDMA450 application. Table 5-2 External Component Information for CDMA450 application Component Model Type Part Number C1 Murata, 2 pF 0402 C3 Murata, 6 pF 0402 C4 Murata, 47 nF 0402 C5 Murata, 5 pF 0402 C6 Murata, 47 nF 0402 C7 Murata, 6 pF 0402 C8 Murata, 100 pF 0402 C9 Murata, 1 nF 0402 C11 Murata, 100 pF 0402 C13 Murata, 5 pF 0402 C14 Murata, 5 pF 0402 C20 Murata, 100 pF 0402 C21 Murata, 1 nF 0402 C22 Murata, 1 nF 0402 L2 Toko, 82 nH 0402 L3 Toko, 22 nH 0402 L4 Toko, 18 nH 0402 L5 Toko, 15 nH 0402 L6 Toko, 220 nH 0603 L7 Toko, 220 nH 0603 L8 Toko, 39 nH 0402 L9 Toko, 3.3 nH 0402 R2 0402 6.8 kΩ 02-IM1010-030827 [email protected] Tel: 82-31-719-4500 Comment 14/19 ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC 7. Package Information (D A T U M B ) D D2 e D/2 NX L D2/2 NX k (NE - 1)ⅹ INDEX AREA ( D/2 ⅹ E/2 ) E/2 (D A T U M A ) E2/2 E E2 aaa C 2X 0. 2X 45 R EF e PIN 1 INDICATOR aaa C NX b bbb M C A B (ND - 1) ⅹ e TOP VIEW BOTTOM VIEW // c c c C NX 0.08 C A1 A3 SIDE VIEW PACKAGE REF A 12L 2.5 ⅹ 2.5 - 0.5 PITCH MIN NOM MAX A 0.80 0.90 1.00 b 0.225 0.25 0.275 D 2.40 2.50 2.60 PACKAGE D2 1.20 1.30 1.40 REF MIN NOM MAX E 2.40 2.50 2.60 A1 0 0.02 0.05 E2 1.20 1.30 1.40 A3 e L 0.50 BSC 0.35 0.40 COMMON DIMENSIONS 0.25 REF K 0.45 0.20 - TOLERANCES OF FORM POSITION N 12 aaa 0.15 ND 3 bbb 0.10 3 ccc 0.10 NE - 1. Dimensioning and tolerancing confirm to ASME Y14 -1994 2. N is the total number of solder pads 3. All dimensions are in millimeter. Angles are in degrees. Fig. 7-1 Package Information 02-IM1010-030827 [email protected] Tel: 82-31-719-4500 15/19 ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC 8. Layout Guidelines The guidelines listed below help the users to achieve the optimum performance of ITM1010 when drawing their layout. These guidelines are recommended. n Keep RF signal lines as short as possible to minimize unnecessary losses and radiation. n For the best noise performance of LNA, keep the pad-to-pad distance in LNA input line as short as possible. The minimum distance is recommended. Also, use high Q components in LNA input-matching circuit. n The 0 ohm resistor between pin 10(LNA_E) and ground is used as a degeneration inductor of the LNA for 800MHz application. This component should not be eliminated. It can also be replaced with chip inductors to increase IP3 of LNA at the cost of smaller gain and higher noise figure. n At the mixer outputs (pin 5 and pin 6), keep the differential signal lines of the same length to ensure signal balance. Symmetrical PCB layout is recommended. n High value (47nF) chip capacitors in the evaluation board (Fig. 4-1) are used for optimum IP3 performance of ITM1010. Do not replace these capacitors with smaller value capacitors. n For various duplexer and RF SAW filters, sensitivity and IMD performance can be optimized by tuning R5, L4 and R2 in Fig. 4-1. n Parasitic impedances at pins 8 (MIX_E) and 10 (LNA_E) might affect RF performance significantly because these pins are used as degeneration. Short PCB lines are recommended for these two pins. n Generally, high LO power is preferable for high gain/IIP3 and low noise figure of the mixer. 02-IM1010-030827 [email protected] Tel: 82-31-719-4500 16/19 ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC 9. Recommended PCB Land Pattern A SOLDER MASK B PKG OUTLINE 2.5 X 2.5 PCB LAND e SOLDER MASK OPENNING E PCB EXPOSED PAD b L M 1. 2. 3. 4. 5. 6. 7. 8. 02-IM1010-030827 D [Unit: mm] REF MIN NOM MAX A 0.0635 B 0.2 D 1.20 1.30 1.40 E 1.20 1.30 1.40 b 0.225 0.25 0.275 e 0.50 BSC L 0.45 0.5 0.55 N 12 M 0.1 N is the total number of solder pads. The exposed pad must be connected to the ground through the via holes and the via holes must be as many as possible. A= Clearance from PCB thermal pad to solder mask opening. B= Clearance from edge of PCB thermal pad to PCB land. L= PCB land length. b= PCB land width. D,E= Ground thermal pad size M= (PCB land length) – (Package solder pad length) [email protected] Tel: 82-31-719-4500 17/19 ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC 10. Tape and Reel Information 02-IM1010-030827 [email protected] Tel: 82-31-719-4500 18/19 ITM1010 CDMA Cellular/CDMA450 Receiver RF Front-end IC 11. Device Marking 1010 YMDX PIN 1 Identifier 1010 YMDX Product Code Name Lot Code Note : The device marking can be subjected to change without any notice. 02-IM1010-030827 [email protected] Tel: 82-31-719-4500 19/19