AGILE OPTICAL COMPONENTS X5 and Z5 Modulator Key Features • Small size: 65 x 12 x 5 mm • Surface mountable with gull wing DC pins • GPO RF connector • Integrated PD (photodiode) for bias and power control • 200 kpsi input fiber for tight bend radii • High bandwidth FEC and super FEC compatible • Zero chirp and chirped modulators in a common package • Operation over C-band and L-band • Low drive voltage • Power penalty without FEC: < 1 dB (±1200 ps/nm) for X5 < 2 dB (1600 ps/nm) for Z5 Applications • MSA transponders using tunable or fixed wavelength sources • TDM and WDM Metro systems with up to 120 km reach • Long Haul (LH) and Ultra Long Haul (ULH) systems (both terrestrial and submarine) • Alternate modulation schemes including electrical RZ Compliance • Telcordia 468 The JDSU Agile Optical Components family includes modulators, switches, attenuators and tunable filters. These products provide the basis for spectrally efficient DWDM transmission utilizing dispersion tolerant modulation, channel monitoring, wavelength switching, remote power control and dynamic channel selection. They support a wide range of flexible functionalities at lower operational expenses for the Agile Optical Network. In addition, we have a complete line of tunable lasers assemblies and sub-assemblies in our Agile Transmission Module family. JDSU X5 and Z5 single drive 10 Gb/s modulators with integrated photodiode are ideally suited for use in long reach (LR)/ very long reach (VR) Metro applications as well as in long haul (LH) transmission. The X5 is a fixed zero-chirp solution and the Z5 is a fixed ±0.7 chirp solution, both packaged identically. The small package form factor makes the X5/Z5 compatible with the 300 pin MSA transponder footprint. The X5 and Z5 modulators operate over the C and L band. Their low drive voltages make them compatible with low power dissipating driver solutions such as GaAs driver technology. In addition to providing bias control feedback, the new enhanced photodiode is capable of power monitoring for control of the transmitter’s modulated output power. NORTH AMERICA : 800 498-JDSU (5378) WORLDWIDE : +800 5378-JDSU WEBSITE : www.jdsu.com X5 AND Z5 MODULATOR 2 Dimensions Diagram (Specifications in mm unless otherwise noted.) O ( .19 4.7 ) 2 PL .73 ( 18.5 ) ±.002 3 ±0.05 ) .26 ( 6.6 ) .30 ( 7.6 ) .23 ( 5.8 ) .47 ( 12 ) 2.45 ( 62.2 ) ±.002 ( 65 0.05 ) 3.84 ( 97.5 ) GPO RF PORT INPUT .10 ( 2.6 ) .192 ±.004 ( 4.86 ±0.1 ) 2X ( .10 2.4 ) OUTPUT 1.299 ( 33 ) 5432 2X ( .079 2) 2X ( .309 7.84 ) DETAIL D Pin Description 1 2 3 4 5 RF input GND DC bias PD anode PD cathode 1 1.000 ( 25.4 ) #2-56 UNC-2B ` .118 4 PL Pinout 1.181 ( 30 ) .780 ( 19.8 ) R ( .59 15 ) MIN. BEND RADIUS 200 KPSI FIBER X5 AND Z5 MODULATOR 3 S21 1 0 S21 [ dB ] -1 -2 -3 -4 -5 -6 0 5 10 15 20 Frequency [ GHz ] S11 0 S11 [ dBe ] -5 -10 -15 -20 -25 -30 0 5 10 15 20 Frequency [ GHz ] Volts Eye Diagram 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 -0.1 (Key feaures: ER >15 dB, jitterp-p <13 ps, measured with optimized driver set-up) 0.0 10.0 20.0 30.0 40.0 50.0 60.0 70.0 80.0 90.0 100.0 110.0 120.0 130.0 140.0 Ps X5 AND Z5 MODULATOR 4 Specifications Parameter Chirp (alpha parameter) Optical insertion loss (BOL)1 Optical return loss (input and output ports) Optical on/off extinction ratio Low frequency PRBS2 E/O bandwidth (-3 dB electrical, linear fit 2 to 15 GHz) S11 (130 MHz to 10 GHz) Drive voltage (RF port)3 Vπ bias port at 40 kHz Bias voltage range4 RF port resistance (DC) Bias port resistance (DC) Photodetector extinction ratio5 Photodetector O/E bandwidth Photodetector responsivity (referenced to output power) Photodetector phase tracking error6 Photodetector dark current (at -5 V, room temperature) ∆R/∆T7 ∆R/∆λ8 X5 Typical Typical Typical 0 ±0.7 4.5 dB 40 dB Typical Typical Typical Typical Typical Typical Typical Typical Typical Typical Typical Typical Typical Typical Typical Z5 27 dB 15 dB 12 GHz 10 dB 5.5 V 4V 4.5 V 2.5 V -15 to 15 V 40 Ω 1 MΩ 6 dB 100 kHz 20 mA/W -5 to 5° 5 nA ±0.2 dB ±0.3 dB 1. Measured at peak of DC bias transmission with no RF input and no optical connectors. 2. For PRBS signals of up to 231-1 and bit rates up to 12.5 Gb/s. Measurement is based on an optimized test set up. 3. Maximum driving voltage required to achieve 15 dB ER for 12.5 Gb/s 231-1 PRBS signal over the operating wavelength and temperature ranges. 4. Maximum voltage range required to maintain optimum bias point over life and temperature. 5. ER = 10*log(Imax/Imin): Imax = PD current with modulator biased to maximum output power, Imin = PD current with modulator biased to minimum output power. 6. Tracking error is the difference in phase between the modulator output power transfer function and the photodetector output current transfer function. 7. The change in responsivity with temperature can be improved from the values given by employing passive thermal compensation. 8. Over C or L band. This can be calibrated for a given laser frequency. X5 AND Z5 MODULATOR Ordering Information For more information on this or other products and their availability, please contact your local JDSU account manager or JDSU directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide or via e-mail at [email protected]. Sample: 21049397 Product Code 21049397 21049396 Description 10 Gb/s X5, SC/UPC output connector 10 Gb/s Z5, SC/UPC output connector Telcordia is a registered trademark of Telcordia Technologies Incorporated. All statements, technical information and recommendations related to the products herein are based upon information believed to be reliable or accurate. However, the accuracy or completeness thereof is not guaranteed, and no responsibility is assumed for any inaccuracies. The user assumes all risks and liability whatsoever in connection with the use of a product or its application. JDSU reserves the right to change at any time without notice the design, specifications, function, fit or form of its products described herein, including withdrawal at any time of a product offered for sale herein. JDSU makes no representations that the products herein are free from any intellectual property claims of others. Please contact JDSU for more information. JDSU and the JDSU logo are trademarks of JDS Uniphase Corporation. Other trademarks are the property of their respective holders. ©2006 JDS Uniphase Corporation. All rights reserved. 21029448 Rev. 006 04/06 X5Z5.DS.CC.AE NORTH AMERICA : 800 498-JDSU (5378) WORLDWIDE : +800 5378-JDSU WEBSITE : www.jdsu.com