LINER LT1236CIN8-10

LT1236
Precision Reference
U
DESCRIPTIO
FEATURES
■
■
■
■
■
■
■
■
■
■
The LT®1236 is a precision reference that combines ultralow drift and noise with excellent long-term stability and
high output accuracy. The reference output will both
source and sink up to 10mA and is almost totally immune
to input voltage variations. Two voltages are available: 5V
and 10V. The 10V version can be used as a shunt regulator
(two-terminal zener) with the same precision characteristics as the three-terminal connection. Special care has
been taken to minimize thermal regulation effects and
temperature induced hysteresis.
Ultra-Low Drift: 5ppm/°C Max
Trimmed to High Accuracy: 0.05% Max
Industrial Temperature Range SO Package
Operates in Series or Shunt Mode
Pin Compatible with AD586, AD587
Output Sinks and Sources in Series Mode
Very Low Noise < 1ppm P-P (0.1Hz to 10Hz)
100% Noise Tested
> 100dB Ripple Rejection
Minimum Input/Output Differential of 1V
The LT1236 combines both superior accuracy and temperature coefficient specifications without the use of high
power, on-chip heaters. The LT1236 references are based
on a buried zener diode structure which eliminates noise
and stability problems with surface breakdown devices.
Further, a subsurface zener exhibits better temperature
drift and time stability than even the best band-gap
references.
UO
APPLICATI
■
■
■
■
■
S
A/D and D/A Converters
Precision Regulators
Precision Scales
Inertial Navigation Systems
Digital Voltmeters
, LTC and LT are registered trademarks of Linear Technology Corporation.
UO
TYPICAL APPLICATI
Typical Distribution of Temperature Drift
Basic Positive and Negative Connections
24
LT1236
IN
OUT
VOUT
NC
IN
GND
OUT
18
GND
16
–VOUT
V
– (V – )
R1 = OUT
ILOAD + 1.5mA
R1
UNITS (%)
VIN
DISTRIBUTION
22 OF THREE RUNS
20
LT1236-10
14
12
10
8
–15V
(V – )
6
4
LT1236 TA01
2
0
–3
–2
–1
0
1
OUTPUT DRIFT (ppm/°C)
2
3
LT1236 TA02
1
LT1236
W W
W
AXI U
U
ABSOLUTE
RATI GS
Input Voltage .......................................................... 40V
Input/Output Voltage Differential ............................ 35V
Output-to-Ground Voltage (Shunt Mode Current Limit)
LT1236-5 ............................................................. 10V
LT1236-10 ........................................................... 16V
Trim Pin-to-Ground Voltage
Positive................................................ Equal to VOUT
Negative ........................................................... – 20V
Output Short-Circuit Duration
VIN = 35V ......................................................... 10 sec
VIN ≤ 20V ................................................... Indefinite
Operating Temperature Range
LT1236AC, BC, CC .................................. 0°C to 70°C
LT1236AI, BI, CI ................................ – 40°C to 85°C
Storage Temperature Range ................ – 65°C to 150°C
Lead Temperature (Soldering, 10 sec)................ 300°C
U
W
U
PACKAGE/ORDER I FOR ATIO
ORDER PART
NUMBER
TOP VIEW
NC* 1
8
NC*
VIN 2
7
NC*
NC* 3
6
V0UT
GND 4
5
TRIM**
N8 PACKAGE
8-LEAD PDIP
*CONNECTED INTERNALLY.
D0 NOT CONNECT EXTERNAL
CIRCUITRY TO THESE PINS
**SEE APPLICATIONS
INFORMATION SECTION
TJMAX = 125°C, θJA = 130°C/W
ORDER PART
NUMBER
TOP VIEW
LT1236ACN8-5
LT1236BCN8-5
LT1236CCN8-5
LT1236ACN8-10
LT1236BCN8-10
LT1236CCN8-10
LT1236AIN8-5
LT1236BIN8-5
LT1236CIN8-5
LT1236AIN8-10
LT1236BIN8-10
LT1236CIN8-10
NC* 1
8
NC*
VIN 2
7
NC*
NC* 3
6
V0UT
GND 4
5
TRIM**
S8 PACKAGE
8-LEAD PLASTIC SO
LT1236ACS8-5
LT1236BCS8-5
LT1236CCS8-5
LT1236ACS8-10
LT1236BCS8-10
LT1236CCS8-10
LT1236AIS8-5
LT1236BIS8-5
LT1236CIS8-5
LT1236AIS8-10
LT1236BIS8-10
LT1236CIS8-10
S8 PART MARKING
*CONNECTED INTERNALLY.
D0 NOT CONNECT EXTERNAL
CIRCUITRY TO THESE PINS
236AC5
236BC5
236CC5
236AC1
236BC1
236CC1
**SEE APPLICATIONS
INFORMATION SECTION
TJMAX = 125°C, θJA = 190°C/W
236AI5
236BI5
236CI5
236AI1
236BI1
236CI1
Consult factory for Military grade parts.
ELECTRICAL CHARACTERISTICS
VIN = 10V, IOUT = 0, TA = 25°C, unless otherwise noted.
PARAMETER
CONDITIONS
Output Voltage (Note 1)
LT1236A-5
LT1236B-5/LT1236C-5
Output Voltage Temperature Coefficient (Note 2)
TMIN ≤ TJ ≤ TMAX
LT1236A-5
LT1236B-5
LT1236C-5
Line Regulation (Note 3)
7.2V ≤ VIN ≤ 10V
MIN
LT1236-5
TYP
MAX
4.9975
4.9950
5.000
5.000
5.0025
5.0050
2
5
10
5
10
15
ppm/°C
ppm/°C
ppm/°C
4
12
20
6
10
ppm/V
ppm/V
ppm/V
ppm/V
20
35
ppm/mA
ppm/mA
●
10V ≤ VIN ≤ 40V
2
●
Load Regulation (Sourcing Current)
(Note 3)
2
0 ≤ IOUT ≤ 10mA
10
●
UNITS
V
V
LT1236
ELECTRICAL CHARACTERISTICS
VIN = 10V, IOUT = 0, TA = 25°C, unless otherwise noted.
PARAMETER
CONDITIONS
Load Regulation (Sinking Current)
(Note 3)
0 ≤ IOUT ≤ 10mA
MIN
LT1236-5
TYP
MAX
UNITS
60
100
150
ppm/mA
ppm/mA
0.8
1.2
1.5
mA
mA
3.5
µVP-P
µVRMS
●
Supply Current
●
Output Voltage Noise
(Note 5)
0.1Hz ≤ f ≤ 10Hz
10Hz ≤ f ≤ 1kHz
3.0
2.2
Long-Term Stability of Output Voltage (Note 6)
∆t = 1000Hrs Non-Cumulative
20
ppm
Temperature Hysteresis of Output (Note 7)
∆T = ±25°C
10
ppm
VIN = 15V, IOUT = 0, TA= 25°C, unless otherwise noted.
PARAMETER
CONDITIONS
MIN
LT1236-10
TYP
MAX
Output Voltage (Note 1)
LT1236A-10
LT1236B-10/LT1236C-10
9.995
9.990
10.000
10.000
10.005
10.010
Output Voltage Temperature Coefficient (Note 2)
TMIN ≤ TJ ≤ TMAX
LT1236A-10
LT1236B-10
LT1236C-10
2
5
10
5
10
15
ppm/°C
ppm/°C
ppm/°C
1.0
4
6
2
4
ppm/V
ppm/V
ppm/V
ppm/V
12
25
40
ppm/mA
ppm/mA
50
100
150
ppm/mA
ppm/mA
1.2
1.7
2.0
mA
mA
1.1
1.5
1.7
mA
mA
Line Regulation (Note 3)
11.5V ≤ VIN ≤ 14.5V
●
14.5V ≤ VIN ≤ 40V
0.5
●
Load Regulation (Sourcing Current)
(Note 3)
0 ≤ IOUT ≤ 10mA
Load Regulation (Shunt Mode)
(Notes 3, 4)
1.7mA ≤ ISHUNT ≤ 10mA
●
●
Series Mode Supply Current
●
Shunt Mode Minimum Current
VIN is Open
●
UNITS
V
V
0.1Hz ≤ f ≤ 10Hz
10Hz ≤ f ≤ 1kHz
6.0
3.5
Long-Term Stablility of Output Voltage (Note 6)
∆t = 1000Hrs Non-Cumulative
30
ppm
Temperature Hysteresis of Output (Note 7)
∆T = ±25°C
5
ppm
Output Voltage Noise (Note 5)
The ● denotes specifications which apply over the specified temperature
range.
Note 1: Output voltage is measured immediately after turn-on. Changes
due to chip warm-up are typically less than 0.005%.
Note 2: Temperature coefficient is measured by dividing the change in
output voltage over the temperature range by the change in temperature.
Incremental slope is also measured at 25°C.
Note 3: Line and load regulation are measured on a pulse basis. Output
changes due to die temperature change must be taken into account
separately.
Note 4: Shunt mode regulation is measured with the input open. With the
input connected, shunt mode current can be reduced to 0mA. Load
regulation will remain the same.
6
µVP-P
µVRMS
Note 5: RMS noise is measured with a 2-pole highpass filter at 10Hz and a
2-pole lowpass filter at 1kHz. The resulting output is full-wave rectified and
then integrated for a fixed period, making the final reading an average as
opposed to RMS. Correction factors are used to convert from average to
RMS, and 0.88 is used to correct for the non-ideal bandbass of the filters.
Peak-to-peak noise is measured with a single highpass filter at 0.1Hz and a
2-pole lowpass filter at 10Hz. The unit is enclosed in a still-air environment
to eliminate thermocouple effects on the leads. Test time is 10 seconds.
Note 6: Long-term stability typically has a logarithmic characteristic and
therefore, changes after 1000 hours tend to be much smaller than before
that time. Total drift in the second thousand hours is normally less than
one third that of the first thousand hours, with a continuing trend toward
reduced drift with time. Significant improvement in long-term drift can be
3
LT1236
ELECTRICAL CHARACTERISTICS
VIN = 15V, IOUT = 0, TA = 25°C, unless otherwise noted.
temperature. Output voltage is always measured at 25°C, but the IC is
cycled to 50°C or 0°C before successive measurements. Hysteresis is
roughly proportional to the square of temperature change. Hysteresis is
not normally a problem for operational temperature excursions, but can be
significant in critical narrow temperature range applications where the
instrument might be stored at high or low temperatures.
realized by preconditioning the IC with a 100-200 hour, 125°C burn in.
Long term stability will also be affected by differential stresses between the
IC and the board material created during board assembly. Temperature
cycling and baking of completed boards is often used to reduce these
stresses in critical applications.
Note 7: Hysteresis in output voltage is created by package stress that
differs depending on whether the IC was previously at a higher or lower
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Ripple Rejection
130
120
100
LT1236-5
95
LT1236-10
100
90
80
LT1236-5
70
90
60
5
10
15 20 25 30
INPUT VOLTAGE (V)
35
100
1k
FREQUENCY (Hz)
10
40
Start-Up (Series Mode)
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
9
8
7
6
LT1236-5
9
VOUT + 2V
0V
8
NC
1k
VOUT
OUT
IN
GND
7
6
8
TIME (µs)
10
12
14
LT1236 G04
4
300
250
200
150
LT1236-10
100
LT1236-5
0
5
4
6 8 10 12 14 16 18 20
OUTPUT CURRENT (mA)
50
4
2
4
350
6
3
2
Output Voltage Noise Spectrum
LT1236-10
LT1236-10
0
400
10
11
0
0.4
LT1236 G03
11
VIN = 0V TO 12V
5
0.6
Start-Up (Shunt Mode), LT1236-10
13
10
0.8
LT1236 G02
LT1236 G01
12
TJ = 25 °C
1.0
0
10k
NOISE VOLTAGE (nV/√Hz)
0
TJ = –55 °C
1.2
0.2
50
85
TJ = 125 °C
1.4
110
LT1236-10
REJECTION (dB)
REJECTION (dB)
110
1.6
VIN = 15V
COUT = 0
f = 150Hz
INPUT/OUTPUT VOLTAGE (V)
115
105
Minimum Input/Output
Differential, LT1236-10
Ripple Rejection
0
2
6
4
TIME (µs)
8
10
12
LT1236 G05
10
1k
100
FREQUENCY (Hz)
1M
LT1236 G06
LT1236
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Output Voltage Temperature Drift
LT1236-5
Output Voltage Noise
COUT = 0
FILTER = 1 POLE
fLOW = 0.1Hz
14
5.004
OUTPUT VOLTAGE (V)
10
8
LT1236-10
4
3
5.003
5.002
5.001
100
1k
BANDWIDTH (Hz)
5.000
–40 –20
10k
40
20
0
60
TEMPERATURE (°C)
Sink Mode* Current Limit,
LT1236-5
60
CURRENT INTO OUTPUT (mA)
1.4
1.2
TJ = – 55°C
1.0
TJ = 25°C
TJ = 125°C
0.6
0.4
2
4 6 8
SINKING
10
LT1236 G09
Thermal Regulation, LT1236-5
VIN = 8V
VIN = 25V
∆POWER = 200mW
50
OUTPUT CHANGE (mV)
IOUT = 0
1.6
0
OUTPUT CURRENT (mA)
LT1236 G08
Quiescent Current, LT1236-5
40
30
20
LOAD
REGULATION
0
– 0.5
THERMAL
REGULATION*
– 1.0
ILOAD = 10mA
10
0.2
0
0
0
5
10
15 20 25 30
INPUT VOLTAGE (V)
35
40
0
2
4
6
8 10 12 14
OUTPUT VOLTAGE (V)
Load Transient Response,
LT1236-5, CLOAD = 0
OUTPUT CHANGE (20mV/DIV)
ISINK = 0
50mV
50mV
ISINK = 0.2mA
ISOURCE = 0.5mA
ISINK = 2-10mA
ISOURCE = 2-10mA
ISINK = 0
20mV
20mV
ISINK = 0.2mA
ISOURCE = 0.2mA
ISINK = 2-10mA
0
1
2
∆ISOURCE = 100µAP-P
∆ISINK = 100µAP-P
3 4 0
TIME (µs)
1
2
3
4
LT1236 G13
0
5
20
40 60 80
TIME (ms)
100 120 140
*INDEPENDENT OF TEMPERATURE COEFFICIENT
LT1236 G12
Output Noise 0.1Hz to 10Hz,
LT1236-5
ISOURCE = 2-10mA
∆ISOURCE = 100µAP-P
0
18
Load Transient Response,
LT1236-5, CLOAD = 1000pF
ISOURCE = 0
ISOURCE = 0
16
*NOTE THAT AN INPUT VOLTAGE IS REQUIRED
FOR 5V UNITS.
LT1236 G11
LT1236 G10
OUTPUT CHANGE (50mV/DIV)
INPUT CURRENT (mA)
–1
–2
–5
–10 – 8 – 6 – 4 – 2
SOURCING
100
80
LT1236 G07
0.8
1
0
–4
LT1236-5
0
1.8
2
–3
2
10
VIN = 8V
FILTERING = 1 ZERO AT 0.1Hz
2 POLES AT 10Hz
OUTPUT VOLTAGE NOISE (5µV/DIV)
RMS NOISE (µV)
5
4
12
6
Load Regulation LT1236-5
5.005
OUTPUT CHANGE (mV)
16
5µV (1ppm)
∆ISINK = 100µAP-P
10 15 20 0
TIME (µs)
5
10 15 20
LT1236 G14
0
1
4
3
2
TIME (MINUTES)
5
6
LT1236 G15
5
LT1236
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Load Regulation, LT1236-10
10.0020
5
10.0015
4
VIN = 12V
10.0000
9.9995
9.9990
9.9985
9.9980
–40
–20
0
20
60
40
TEMPERATURE (˚C)
80
INPUT CURRENT (mA)
10.0005
2
1
0
–1
–2
2
4 6 8
SINKING
TJ = 125°C
1.0
0.8
0.6
0
10
1.4
1.2
TJ = – 55°C
0.8
TJ = 25°C
0.4
TJ = 125°C
0
2
4
6
10
8
OUTPUT TO GROUND VOLTAGE (V)
35
40
Thermal Regulation, LT1236-10
INPUT PIN OPEN
VIN = 30V
∆POWER = 200mW
50
40
30
20
LOAD
REGULATION
0
– 0.5
–1.0
THERMAL
REGULATION*
–1.5
ILOAD = 10mA
10
0
12
15 20 25 30
INPUT VOLTAGE (V)
LT1236 G18
0
0
10
LT1236 G17
OUTPUT CHANGE (mV)
INPUT PIN OPEN
5
0
Shunt Mode Current Limit,
LT1236-10
CURRENT INTO OUTPUT (mA)
CURRENT INTO OUTPUT (mA)
0
OUTPUT CURRENT (mA)
1.6
0.2
TJ = 25°C
1.2
0.2
60
0.6
1.4
–4
Shunt Characteristics, LT1236-10
1.0
TJ = – 55°C
0.4
–5
–10 – 8 – 6 – 4 – 2
SOURCING
100
IOUT = 0
1.6
–3
LT1236 G16
1.8
Input Supply Current, LT1236-10
1.8
3
10.0010
OUTPUT CHANGE (mV)
OUTPUT VOLTAGE (V)
Output Voltage Temperature
Drift, LT1236-10
2
4
6
8 10 12 14
OUTPUT VOLTAGE (V)
16
LT1236 G20
LT1236 G19
0
18
20
40 60 80
TIME (ms)
100 120 140
*INDEPENDENT OF TEMPERATURE COEFFICIENT
LT1236 G21
Load Transient Response,
LT1236-10, CLOAD = 0
OUTPUT VOLTAGE CHANGE
OUTPUT VOLTAGE CHANGE
ISOURCE = 0
50mV
10mV
ISINK = 0.8mA
ISOURCE = 0.2mA
ISINK = 1.0mA
1
2
3 4 0
TIME (µs)
1
3
2
ISINK = 1.2mA
ISOURCE = 0.5mA
ISOURCE = 2-10mA
∆ISOURCE = 100µAP-P
∆ISINK = 100µAP-P
4
NOTE VERTICAL SCALE CHANGE
BETWEEN SOURCING AND SINKING
LT1236 G22
6
5mV
ISINK = 2-10mA
ISOURCE = 2-10mA
∆ISOURCE = 100µAP-P
20mV
0
1
2
ISINK = 1.4mA
ISINK = 2-10mA
∆ISINK = 100µAP-P
3 4 0
TIME (µs)
1
3
2
4
NOTE VERTICAL SCALE CHANGE
BETWEEN SOURCING AND SINKING
LT1236 G23
FILTERING = 1 ZERO AT 0.1Hz
2 POLES AT 10Hz
OUTPUT VOLTAGE NOISE (10µV/DIV)
ISINK = 0.8mA
ISINK = 0.6mA
ISOURCE = 0
0
Output Noise 0.1Hz to 10Hz,
LT1236-10
Load Transient Response,
LT1236-10, CLOAD = 1000pF
10µV (1ppm)
0
1
4
3
2
TIME (MINUTES)
5
6
LT1236 G24
LT1236
U
U
W
U
APPLICATIONS INFORMATION
Effect of Reference Drift on System Accuracy
A large portion of the temperature drift error budget in
many systems is the system reference voltage. This graph
indicates the maximum temperature coefficient allowable
if the reference is to contribute no more than 0.5LSB error
to the overall system performance. The example shown is
a 12-bit system designed to operate over a temperature
range from 25°C to 65°C. Assuming the system calibration is performed at 25°C, the temperature span is 40°C.
It can be seen from the graph that the temperature coefficient of the reference must be no worse than 3ppm/°C if
it is to contribute less than 0.5LBS error. For this reason,
the LT1236 family has been optimized for low drift.
MAXIMUM TEMPERATURE COEFFICIENT FOR
0.5LSB ERROR (ppm/°C)
Maximum Allowable Reference Drift
100
in series with a 20kΩ potentiometer will give ±10mV trim
range. Effect on the output TC will be only 1ppm/°C for the
± 5mV trim needed to set the “A” device to 10.000V.
LT1236-5
The LT1236-5 does have an output voltage trim pin, but
the TC of the nominal 4V open circuit voltage at pin 5 is
about –1.7mV/°C. For the voltage trimming not to affect
reference output TC, the external trim voltage must track
the voltage on the trim pin. Input impedance of the trim pin
is about 100kΩ and attenuation to the output is 13:1. The
technique shown below is suggested for trimming the
output of the LT1236-5 while maintaining minimum shift
in output temperature coefficient. The R1/R2 ratio is
chosen to minimize interaction of trimming and TC shifts,
so the exact values shown should be used.
8-BIT
LT1236-5
IN
10-BIT
10
GND
VOUT
OUT
TRIM
R1
27k
R2
50k
12-BIT
1N4148
14-BIT
1.0
LT1236 AI02
10 20 30 40 50 60 70 80 90 100
TEMPERATURE SPAN (°C)
LT1236 AI01
Trimming Output Voltage
The LT1236-10 has a trim pin for adjusting output voltage.
The impedance of the trim pin is about 12kΩ with a
nominal open circuit voltage of 5V. It is designed to be
driven from a source impedance of 3kΩ or less to minimize changes in the LT1236 TC with output trimming.
Attenuation between the trim pin and the output is 70:1.
This allows ±70mV trim range when the trim pin is tied to
the wiper of a potentiometer connected between the
output and ground. A 10kΩ potentiometer is recommended, preferably a 20 turn cermet type with stable
characteristics over time and temperature.
The LT1236-10 “A” version is pre-trimmed to ±5mV and
therefore can utilize a restricted trim range. A 75k resistor
Capacitive Loading and Transient Response
The LT1236 is stable with all capacitive loads, but for
optimum settling with load transients, output capacitance
should be under 1000pF. The output stage of the reference
is class AB with a fairly low idling current. This makes
transient response worse-case at light load currents.
Because of internal current drain on the output, actual
worst-case occurs at ILOAD = 0 on LT1236-5 and ILOAD =
1.4mA (sinking) on LT1236-10. Significantly better load
transient response is obtained by moving slightly away
from these points. See Load Transient Response curves
for details. In general, best transient response is obtained
when the output is sourcing current. In critical applications, a 10µF solid tantalum capacitor with several ohms
in series provides optimum output bypass.
7
LT1236
U
W
U
U
APPLICATIONS INFORMATION
Kelvin Connections
Although the LT1236 does not have true force/sense
capability at its outputs, significant improvements in ground
loop and line loss problems can be achieved with proper
hook-up. In series mode operation, the ground pin of the
LT1236 carries only ≈ 1mA and can be used as a sense
line, greatly reducing ground loop and loss problems on
the low side of the reference. The high side supplies load
current so line resistance must be kept low. Twelve feet of
#22 gauge hook-up wire or 1 foot of 0.025 inch printed
circuit trace will create 2mV loss at 10mA output current.
This is equivalent to 1LSB in a 10V, 12-bit system.
The following circuits show proper hook-up to minimize
errors due to ground loops and line losses. Losses in the
output lead can be greatly reduced by adding a PNP boost
transistor if load currents are 5mA or higher. R2 can be
added to further reduce current in the output sense lead.
temperature gradients in the package leads. Variations in
thermal resistance, caused by uneven air flow, create
differential lead temperatures, thereby causing thermoelectric voltage noise at the output of the reference.
Standard Series Mode
LT1236
INPUT
IN
KEEP THIS LINE RESISTANCE LOW
OUT
+
GND
LOAD
GROUND
RETURN
LT1236 AI03
Series Mode with Boost Transistor
INPUT
R1
220Ω
2N3906
Effects of Air Movement on Low Frequency Noise
The LT1236 has very low noise because of the buried zener
used in its design. In the 0.1Hz to 10Hz band, peak-to-peak
noise is about 0.5ppm of the DC output. To achieve this
low noise, however, care must be taken to shield the
reference from ambient air turbulence. Air movement can
create noise because of thermoelectric differences between IC package leads and printed circuit board materials
and/or sockets. Power dissipation in the reference, even
though it rarely exceeds 20mW, is enough to cause small
IN
LT1236
OUT
GND
LOAD
R2*
GROUND
RETURN
*OPTIONAL—REDUCES CURRENT IN OUTPUT SENSE
LEAD: R2 = 2.4k (LT1236-5), 5.6k (LT1236-10)
LT1236 AI04
U
TYPICAL APPLICATIONS
Restricted Trim Range for Improved
Resolution, 10V, “A” Version Only
LT1236-10 Full Trim Range (±0.7%)
Negative Series Reference
15V
LT1236-10
LT1236A-10
VIN
IN
GND
10.000V
OUT
TRIM
R1
75k
R2
50k
VIN
IN
GND
R1
4.7k
VOUT
OUT
IN
TRIM
R2
4.7k
R1*
10k
–15V
LT1236 TA03
TRIM RANGE ≈ ±10mV
8
LT1236 TA10
LT1236-10
*CAN BE RAISED TO 20k FOR LESS
CRITICAL APPLICATIONS
D1
15V
Q1
2N2905
OUT
GND
–10V AT
50mA
LT1236 TA04
LT1236
U
TYPICAL APPLICATIONS
Boosted Output Current
with No Current Limit
Boosted Output Current
with Current Limit
±10V Output Reference
V+ ≥ VOUT + 2.8V
V + ≥ (VOUT + 1.8V)
D1*
LED
R1
220Ω
R1
220Ω
LT1236-10
8.2Ω
15V
VOUT
VIN
2N2905
2N2905
+10V
GND
IN
IN
LT1236
10V AT
100mA
OUT
GND
+
COM
LT1236
10V AT
100mA
OUT
2µF
SOLID
TANT
GND
+
LT1236-10
VOUT
V IN
2µF
SOLID
TANT
GND
–10V
LT1236 TA05
*GLOWS IN CURRENT LIMIT,
DO NOT OMIT
–15V –10V
R1 =
ILOAD + 1.5mA
LT1236 TA06
ILOAD
R1
–15V
Handling Higher Load Currents
15V
LT1236 TA17
Operating 5V Reference from 5V Supply
5V LOGIC
SUPPLY
30mA
1N914
CMOS LOGIC GATE**
R1*
169Ω
IN
LT1236-10
fIN ≥ 2kHz*
VOUT
10V
OUT
TYPICAL LOAD
CURRENT = 30mA
LT1236-5
1N914
≈8.5V
+ C2*
C1*
5µF
GND
RL
+
IN
OUT
5V
REFERENCE
GND
5µF
*FOR HIGHER FREQUENCIES C1 AND C2 MAY BE DECREASED
**PARALLEL GATES FOR HIGHER REFERENCE CURRENT LOADING
LT1236 TA15
*SELECT R1 TO DELIVER TYPICAL LOAD CURRENT.
LT1236 WILL THEN SOURCE OR SINK AS NECESSARY
TO MAINTAIN PROPER OUTPUT. DO NOT REMOVE LOAD
AS OUTPUT WILL BE DRIVEN UNREGULATED HIGH. LINE
REGULATION IS DEGRADED IN THIS APPLICATION
LT1236 TA07
Trimming 10V Units to 10.24V
CMOS DAC with Low Drift Full-Scale Trimming**
LT1236-10
R3
4.02K
1%
OUT
LT1236-10
TRIM
GND
FB
R1
4.99k
1%
REF
CMOS
DAC
LTC7543
30pF
IOUT
R2
40.2Ω
1%
1.2k
–15V
*TC LESS THAN 200ppm/°C
**NO ZERO ADJUST REQUIRED
WITH LT1007 (V0S ≤ 60µV)
VIN
R4*
100Ω
FULL-SCALE
ADJUST
TRIM
OUT
VOUT = 10.24V
GND
4.32k
–
LT1007C
+
IN
10V
F.S.
5k
V – = –15V*
LT1236 TA14
*MUST BE WELL REGULATED
dVOUT 15mV
=
V
dV –
LT1236 TA11
9
LT1236
U
TYPICAL APPLICATIONS
Negative Shunt Reference Driven
by Current Source
Strain Gauge Conditioner for 350Ω Bridge
R1
357Ω
1/2W
LT1236-10
28mA
LT1236-10
15V
IN
OUT
28.5mA
GND
OUT
5V
350Ω STRAIN
GAUGE BRIDGE**
GND
+
6
–
100pF
2
R4
20k
LM301A†
1
2.5mA
R2
20k
3
2
–10V (ILOAD ≤ 1mA)
R3
2M
–
LT1012C
3
6
LM334
VOUT
X100
+
R5
2M
8
27Ω
R6*
2M
–11V TO – 40V
–5V
LT1236 TA13
357Ω
1/2W
–15V
*THIS RESISTOR PROVIDES POSITIVE FEEDBACK TO
THE BRIDGE TO ELIMINATE LOADING EFFECT OF
THE AMPLIFIER. EFFECTIVE ZIN OF AMPLIFIER
STAGE IS ≥ 1MΩ. IF R2 TO R5 ARE CHANGED,
SET R6 = R3
**BRIDGE IS ULTRA-LINEAR WHEN ALL LEGS ARE
ACTIVE, TWO IN COMPRESSION AND TWO IN TENSION,
OR WHEN ONE SIDE IS ACTIVE WITH ONE COMPRESSED
AND ONE TENSIONED LEG
†
OFFSET AND DRIFT OF LM301A ARE VIRTUALLY
ELIMINATED BY DIFFERENTIAL CONNECTION OF LT1012C
LT1236 TA08
2-Pole Lowpass Filtered Reference
Precision DAC Reference with System TC Trim
1µF
MYLAR
LT1236-10
15V
IN
–
OUT
GND
VIN
8.87k
1%
VIN
D1
1N457
1.24k
1%
LT1001
LT1236
50k
TC TRIM*
10k
1%
10k
1%
D2
1N457
50k
ROOM TEMP
TRIM
IN
GND
R1
36k
R2
36k
f = 10Hz
10.36k
1%
200k
1%
VREF
+
OUT
0.5µF
MYLAR
TOTAL NOISE
≤2µVRMS
1Hz ≤ f ≤ 10kHz
–VREF
LT1236 TA12
50k
*TRIMS 1mA REFERENCE CURRENT
TC BY ±40ppm/°C. THIS TRIM
SCHEME HAS VERY LITTLE EFFECT ON ROOM
TEMPERATURE CURRENT TO MINIMIZE ITERATIVE
TRIMMING
10
8.45k
1mA
DAC
LT1236 TA16
LT1236
U
TYPICAL APPLICATIONS
Ultra-Linear Platinum Temperature Sensor*
LT1236-10
IN
OUT
20V
GND
R2*
5k
R10
182k
1%
R14
5k
R1**
253k
R9
100k
R11
6.65M
1%
R8
10M
R15
10k
Rf**
654k
R12
1k
R13
24.3k
20V
R4
4.75k
1%
R3**
5k
RS†
100Ω AT
0°C
2
R5
200k
1%
LT1001
3
R6
619k
1%
R7
392k
1%
–15V
7
–
+
6
VOUT =100mV/°C
–50°C ≤ T ≤ 150°C
4
–15V
†
STANDARD INDUSTRIAL 100Ω PLATINUM 4-WIRE SENSOR,
ROSEMOUNT 78S OR EQUIVALENT. α = 0.00385
TRIM R9 FOR VOUT = 0V AT 0°C
TRIM R12 FOR VOUT = 10V AT 100°C
TRIM R14 FOR VOUT = 5V AT 50°C
USE TRIM SEQUENCE AS SHOWN. TRIMS ARE NONINTERACTIVE
SO THAT ONLY ONE TRIM SEQUENCE IS NORMALLY REQUIRED.
*FEEDBACK LINEARIZES OUTPUT TO ± 0.005°C FROM
– 50°C TO 150°C
LT1236 TA09
**WIREWOUND RESISTORS WITH LOW TC
U
W
EQUIVALE T SCHE ATIC
INPUT
Q3
D1
D2
OUTPUT
D3
R1
Q1
+
–
A1
R2
D4
6.3V
Q2
GND
LT1236 ES
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
11
LT1236
U
PACKAGE DESCRIPTION Dimensions in inches (millimeters) unless otherwise noted.
N8 Package
8-Lead Plastic DIP
0.300 – 0.325
(7.620 – 8.255)
0.045 – 0.065
(1.143 – 1.651)
(
0.130 ± 0.005
(3.302 ± 0.127)
0.065
(1.651)
TYP
0.009 – 0.015
(0.229 – 0.381)
+0.025
0.325 –0.015
+0.635
8.255
–0.381
0.400*
(10.160)
MAX
7
6
5
1
2
3
4
0.255 ± 0.015*
(6.477 ± 0.381)
0.125
(3.175)
MIN
0.045 ± 0.015
(1.143 ± 0.381)
)
8
0.015
(0.380)
MIN
0.018 ± 0.003
(0.457 ± 0.076)
0.100 ± 0.010
(2.540 ± 0.254)
N8 0395
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm).
S8 Package
8-Lead Plastic SOIC
0.189 – 0.197*
(4.801 – 5.004)
0.010 – 0.020
× 45°
(0.254 – 0.508)
0.008 – 0.010
(0.203 – 0.254)
0.053 – 0.069
(1.346 – 1.752)
0.004 – 0.010
(0.101 – 0.254)
8
7
6
5
0°– 8° TYP
0.016 – 0.050
0.406 – 1.270
0.014 – 0.019
(0.355 – 0.483)
0.050
(1.270)
BSC
0.150 – 0.157*
(3.810 – 3.988)
0.228 – 0.244
(5.791 – 6.197)
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006 INCH (0.15mm).
1
2
3
4
SO8 0294
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1019
Precision Bandgap Reference
0.05%, 5ppm/°C
LT1027
Precision 5V Reference
0.02%, 2ppm/°C
12
Linear Technology Corporation
LT/GP 0695 10K • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7487
(408) 432-1900 ● FAX: (408) 434-0507 ● TELEX: 499-3977
 LINEAR TECHNOLOGY CORPORATION 1995