LINER RH1021BM-10

RH1021-10
Precision 10V Reference
U
W W
W
U
DESCRIPTION
ABSOLUTE MAXIMUM RATINGS
The RH1021-10 is a precision 10V reference with ultralow
drift and noise, extremely good long-term stability and
almost total immunity to input voltage variations. The
reference output will source and sink up to 10mA. This
reference can also be used as a shunt regulator
(2-terminal Zener). Unique circuit design makes the
RH1021-10 the first IC reference to offer ultralow drift
without the use of high power on-chip heaters.
Input Voltage ........................................................... 40V
Input/Output Voltage Differential ............................. 35V
Output to Ground Voltage
(Shunt Mode Current Limit) ............................... 16V
Trim Pin to Ground Voltage
Positive................................................ Equal to VOUT
Negative ........................................................... – 20V
Output Short-Circuit Duration
VIN = 35V ........................................................ 10 sec
VIN ≤ 20V ................................................... Indefinite
Operating Temperature Range .............. – 55°C to 125°C
Storage Temperature Range ................. – 65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
W
, LTC and LT are registered trademarks of Linear Technology Corporation.
U U
U
BUR -I CIRCUIT
U
The wafer lots are processed to Linear Technology’s inhouse Class S flow to yield circuits usable in stringent
military applications.
PACKAGE/ORDER INFORMATION
TOP VIEW
NC*
8
7
1
8
NC* 1
20V
2
7 NC*
6
RH1021-10
6 VOUT
VIN 2
5
3
4
5 TRIM
NC* 3
4
GND
–20V
H PACKAGE
8-LEAD TO-5 METAL CAN
* Connected internally. Do not connect external
circuitry to these pins.
1
RH1021-10
TABLE 1: ELECTRICAL CHARACTERISTICS
SYMBOL PARAMETER
CONDITIONS
VOUT
Output Voltage
TCVOUT
(Preirradiation) (Note 9)
TA = 25°C
TYP MAX
NOTES
MIN
RH1021CM-10
RH1021BM-10, DM-10
1
1
9.995
9.95
Output Voltage
Temperature Coefficient
RH1021BM-10
RH1021CM-10, DM-10
2
2
∆VOUT
∆VIN
Line Regulation
11.5V ≤ VIN ≤ 14.5V
14.5V ≤ VIN ≤ 40V
3
3
4
2
∆VOUT
∆IOUT
Load Regulation
(Sourcing Current)
0 ≤ IOUT ≤ 10mA
3
Load Regulation (Shunt Mode)
1.7mA ≤ IOUT ≤ 10mA
3,4
10.005
10.05
SUB- – 55°C ≤ TA ≤ 125°C SUBGROUP MIN TYP MAX
GROUP
1
1
UNITS
V
V
5
20
2,3
2,3
ppm/°C
ppm/°C
1
1
6
4
2,3
2,3
ppm/V
ppm/V
25
1
40
2,3
ppm/mA
100
1
150
2,3
ppm/mA
IS
Supply Current (Series Mode)
1.7
1
2.0
2,3
mA
IMIN
Minimum Current (Shunt Mode) VIN Is Open
1.5
1
1.7
2,3
mA
6
4
0.1Hz ≤ f ≤ 10Hz
10Hz ≤ f ≤ 1kHz
5
5
6
Long-Term Stability
of VOUT
∆T = 1000 Hrs
Noncumulative
6
15
ppm
Temperature Hysteresis
of VOUT
∆T = ±25°C
5
ppm
Output Voltage Noise
TABLE 1A: ELECTRICAL CHARACTERISTICS
10Krad(Si)
NOTES MIN MAX
µVP-P
µVRMS
(Postirradiation) (Note 7)
20Krad(Si) 50Krad(Si)
MIN MAX MIN MAX
100Krad(Si) 200Krad(Si)
MIN MAX MIN MAX
UNITS
9.995 10.005 9.99 10.01 9.987 10.013 9.985 10.015 9.98 10.02
9.95 10.05 9.945 10.055 9.942 10.06 9.98 10.06 9.935 10.065
V
V
SYMBOL PARAMETER
CONDITIONS
VOUT
Output Voltage
RH1021CM-10
RH1021BM-10, DM-10
1
1
TCVOUT
Output Voltage
Temperature Coefficient
RH1021BM-10
RH1021CM-10, DM-10
2
2
5
20
5
20
5
20
7
22
10
25
ppm/°C
ppm/°C
∆VOUT
∆VIN
Line Regulation
11.5V ≤ VIN ≤ 14.5V
14.5V ≤ VIN ≤ 40V
3
3
4
2
4
2
4.5
2
5
2
6
3
ppm/V
ppm/V
∆VOUT
∆IOUT
Load Regulation
(Sourcing Current)
0 ≤ IOUT ≤ 10mA
3,8
25
25
25
25
25
ppm/mA
Load Regulation
(Shunt Mode)
1.7mA ≤ IOUT ≤ 10mA
3,4
100
100
100
100
150
ppm/mA
IMIN
Minimum Current
(Shunt Mode)
VIN Is Open
1.5
1.5
1.5
1.5
1.5
mA
IS
Supply Current
(Series Mode)
1.7
1.7
1.7
1.7
1.7
mA
2
RH1021-10
TABLE 1A: ELECTRICAL CHARACTERISTICS
Note 1: Output voltage is measured immediately after turn-on. Changes
due to chip warm-up are typically less than 0.005%.
Note 2: Temperature coefficient is measured by dividing the change in
output voltage over the temperature range by the change in temperature.
Separate tests are done for hot and cold; TMIN to 25°C and 25°C to TMAX.
Incremental slope is also measured at 25°C.
Note 3: Line and load regulation are measured on a pulse basis. Output
changes due to die temperature change must be taken into account
separately. Package thermal resistance is 150°C/W for the TO-5 (H)
package.
Note 4: Shunt mode regulation is measured with the input open. With the
input connected, shunt mode current can be reduced to 0mA. Load
regulation will remain the same.
Note 5: RMS noise is measured with a 2-pole highpass filter at 10Hz and a
2-pole lowpass filter at 1kHz. The resulting output is full wave rectified and
then integrated for a fixed period, making the final reading an average as
opposed to RMS. Correction factors are used to convert from average to
RMS and to correct for the nonideal bandpass of the filters. Peak-to-peak
noise is measured with a single highpass filter at 0.1Hz and a 2-pole
lowpass filter at 10Hz. The unit is enclosed in a still-air environment to
eliminate thermocouple effects on the leads. Test time is 10 seconds.
Note 6: Consult factory for units with long term stability data.
Note 7: VIN = 12V, IOUT = 0, TA = 25°C, unless otherwise noted.
Note 8: IOUT(MAX) (Sourcing) is 5mA for exposures greater than
100Krad (Si).
Note 9: VIN = 12V, IOUT = 0, unless otherwise noted.
U W
TABLE 2: ELECTRICAL TEST REQUIRE E TS
MIL-STD-883 TEST REQUIREMENTS
PDA Test Notes
The PDA is specified as 5% based on failures from group A, subgroup 1,
tests after cooldown as the final electrical test in accordance with method
5004 of MIL-STD-883. The verified failures of group A, subgroup 1, after
burn-in divided by the total number of devices submitted for burn-in in
that lot shall be used to determine the percent for the lot.
Linear Technology Corporation reserves the right to test to tighter limits
than those given.
SUBGROUP
Final Electrical Test Requirements (Method 5004)
1*,2,3,4
Group A Test Requirements (Method 5005)
1,2,3,4
Group B and D for Class S, and
Group C and D for Class B
End Point Electrical Parameters (Method 5005)
1
* PDA Applies to subgroup 1. See PDA Test Notes.
TOTAL DOSE BIAS CIRCUIT
15V
VIN
GND
–15V
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
3
RH1021-10
U W
TYPICAL PERFORMANCE CHARACTERISTICS
Output Voltage
Load Regulation (Shunt Mode)
10.00
9.99
10
100
TOTAL DOSE Krad (Si)
VIN = OPEN
1.2mA ≤ IOUT ≤ 10mA
50
30
20
10
1000
Line Regulation
10
100
TOTAL DOSE Krad (Si)
NOTE 8
1000
1
–1.0
–1.5
1000
10
100
TOTAL DOSE Krad (Si)
Minimum Current (Shunt Mode)
1.2
VIN = 15V
VIN = OPEN
10
1.1
5
0
–5
–10
–15
RH1021-10 G04
1000
RH1021-10 G03
MINIMUM CURRENT (mA)
TEMPERATURE COEFFICIENT (ppm/°C)
LINE REGULATION (ppm/V)
11.5V ≤ VIN ≤ 14.5V
10
100
TOTAL DOSE Krad (Si)
8
Temperature Coefficient
14.5V ≤ VIN ≤ 40V
1
10
4
1
15
–0.5
12
RH1021-10 G02
1.0
0
14
6
RH1021-10 G01
0.5
V IN = 15V
0mA ≤ IOUT ≤ 10mA
16
40
0
1
18
LOAD REGULATION (ppm/mA)
LOAD REGULATION (ppm/mA)
OUTPUT VOLTAGE (V)
V IN = 15V
IOUT = 0
–2.0
Load Regulation (Sourcing)
60
10.01
1.0
0.9
0.8
0.7
1
10
100
TOTAL DOSE Krad (Si)
1000
RH1021-10 G05
0.6
1
10
100
TOTAL DOSE Krad (Si)
1000
RH1021-10 G06
I.D. No. 66-10-0179 Rev. A 0796
4
Linear Technology Corporation
LT/HP 0796 500 REV A • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507 ● TELEX: 499-3977
 LINEAR TECHNOLOGY CORPORATION 1990