LTC3808 No RSENSETM, Low EMI, Synchronous DC/DC Controller with Output Tracking DESCRIPTIO U FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ The LTC®3808 is a synchronous step-down switching regulator controller that drives external complementary power MOSFETs using few external components. The constant frequency current mode architecture with MOSFET VDS sensing eliminates the need for a current sense resistor and improves efficiency. Programmable Output Voltage Tracking Sense Resistor Optional Spread Spectrum Modulation for Low Noise Constant Frequency Current Mode Operation for Excellent Line and Load Transient Response Wide VIN Range: 2.75V to 9.8V Wide VOUT Range: 0.6V to VIN 0.6V ±1.5% Reference Low Dropout Operation: 100% Duty Cycle True PLL for Frequency Locking or Adjustment (Frequency Range: 250kHz to 750kHz) Selectable Burst Mode®/Pulse Skipping/Forced Continuous Operation Auxiliary Winding Regulation Internal Soft-Start Circuitry Power Good Output Voltage Monitor Output Overvoltage Protection Micropower Shutdown: IQ = 9µA Tiny Thermally Enhanced Leadless (4mm × 3mm) DFN or 16-lead SSOP Package Burst Mode operation provides high efficiency operation at light loads. 100% duty cycle provides low dropout operation, extending operating time in battery-powered systems. The switching frequency can be programmed up to 750kHz, allowing the use of small surface mount inductors and capacitors. For noise sensitive applications, the LTC3808 can be externally synchronized from 250kHz to 750kHz. Burst Mode is inhibited during synchronization or when the SYNC/MODE pin is pulled low to reduce noise and RF interference. To further reduce EMI, the LTC3808 incorporates a novel spread spectrum frequency modulation technique. U APPLICATIO S ■ ■ ■ , LTC and LT are registered trademarks of Linear Technology Corporation. Burst Mode is a registered trademark of Linear Technology Corporation. No RSENSE is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 5481178, 5929620, 6580258, 6304066, 5847554, 6611131, 6498466. Other Patents pending. One or Two Cell Lithium-Ion Powered Devices Notebook and Palmtop Computers, PDAs Portable Instruments Distributed DC Power Systems U ■ The LTC3808 is available in the tiny footprint thermally enhanced DFN package or 16-lead SSOP package. TYPICAL APPLICATIO Efficiency and Power Loss vs Load Current 100 10k EFFICIENCY High Efficiency, 550kHz Step-Down Converter 1M LTC3808 PLLLPF 15k 187k 220pF VIN SENSE+ SYNC/MODE 59k 10µF TG PGOOD VFB SW ITH BG 2.2µH IPRG RUN + VOUT 2.5V 2A VIN = 3.3V 90 VIN = 5V 80 100 TYPICAL POWER LOSS (VIN = 4.2V) 70 1 FIGURE 11 CIRCUIT VOUT = 2.5V 50 1 3808 TA01 10 60 47µF GND 1k VIN = 4.2V POWER LOSS (mW) VIN 2.75V TO 9.8V EFFICIENCY (%) ■ 10 100 1k LOAD CURRENT (mA) 0.1 10k 3808 TA01b 3808f 1 LTC3808 U W W W ABSOLUTE MAXIMUM RATINGS (Note 1) Input Supply Voltage (VIN)........................ – 0.3V to 10V PLLLPF, RUN, SYNC/MODE, TRACK/SS, SENSE+, IPRG Voltages ............ – 0.3V to (VIN + 0.3V) VFB, ITH Voltages...................................... –0.3V to 2.4V SW, SENSE– Voltages......... – 2V to VIN + 1V (10V Max) PGOOD ..................................................... – 0.3V to 10V TG, BG Peak Output Current (<10µs) ........................ 1A Operating Temperature Range (Note 2)... – 40°C to 85°C Storage Ambient Temperature Range ... – 65°C to 125°C Junction Temperature (Note 3) ............................ 125°C Lead Temperature (Soldering, 10 sec) GN16 Package .................................................. 300°C W U U PACKAGE/ORDER INFORMATION ORDER PART NUMBER TOP VIEW PLLLPF 1 14 SW – SYNC/MODE 2 13 SENSE TRACK/SS 3 PGOOD 4 12 VIN 11 SENSE+ VFB 5 10 TG ITH 6 9 BG RUN 7 8 IPRG 15 DE PACKAGE 14-LEAD (4mm × 3mm) PLASTIC DFN LTC3808EDE ORDER PART NUMBER TOP VIEW GND 1 16 SW PLLLPF 2 15 SENSE– SYNC/MODE 3 14 VIN TRACK/SS 4 13 SENSE+ PGOOD 5 12 TG VFB 6 11 BG ITH 7 10 IPRG RUN 8 9 DE PART MARKING 3808 LTC3808EGN GND GN PACKAGE 16-LEAD PLASTIC SSOP TJMAX = 125°C, θJA = 37°C/W EXPOSED PAD (PIN 15) IS GND (MUST BE SOLDERED TO PCB) TJMAX = 125°C, θJA = 130°C/W Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS The ● indicates specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VIN = 4.2V unless otherwise noted. PARAMETER CONDITIONS MIN TYP MAX UNITS 350 105 9 9 500 150 20 20 µA µA µA µA 1.95 2.15 2.25 2.45 2.55 2.75 V V 0.8 1.1 1.4 V 0.65 1 1.35 µA Main Control Loops Input DC Supply Current Normal Operation Sleep Mode Shutdown UVLO (Note 4) Undervoltage Lockout Threshold VIN Falling VIN Rising RUN = 0V VIN = UVLO Threshold – 200mV ● ● Shutdown Threshold of RUN Pin Start-Up Current Source TRACK/SS = 0V Regulated Feedback Voltage (Note 5) 0.6 0.609 V Output Voltage Line Regulation 2.75V < VIN < 9.8V (Note 5) 0.01 0.04 %/V Output Voltage Load Regulation ITH = 0.9V (Note 5) ITH = 1.7V 0.1 –0.1 0.5 –0.5 % % VFB Input Current (Note 5) 9 50 nA Overvoltage Protect Threshold Measured at VFB 0.68 0.7 V ● 0.591 0.66 3808f 2 LTC3808 ELECTRICAL CHARACTERISTICS The ● indicates specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VIN = 4.2V unless otherwise noted. PARAMETER CONDITIONS MIN Overvoltage Protect Hysteresis TYP MAX 20 Auxiliary Feedback Threshold 0.325 0.4 UNITS mV 0.475 V Top Gate (TG) Drive Rise Time CL = 3000pF 40 ns Top Gate (TG) Drive Fall Time CL = 3000pF 40 ns Bottom Gate (BG) Drive Rise Time CL = 3000pF 50 ns Bottom Gate (BG) Drive Fall Time CL = 3000pF Maximum Current Sense Voltage (∆VSENSE(MAX)) (SENSE+ – SW) IPRG = Floating (Note 6) IPRG = 0V (Note 6) IPRG = VIN (Note 6) Soft-Start Time (Internal) 40 ● ● ● ns 110 70 185 125 85 204 140 100 223 mV mV mV Time for VFB to Ramp from 0.05V to 0.55V 0.5 0.74 0.9 ms Unsynchronized (SYNC/MODE Not Clocked) PLLLPF = Floating PLLLPF = 0V PLLLPF = VIN 480 260 650 550 300 750 600 340 825 kHz kHz kHz SYNC/MODE Clocked Minimum Synchronizable Frequency Maximum Synchronizible Frequency 200 1000 250 750 kHz kHz Oscillator and Phase-Locked Loop Oscillator Frequency Phase-Locked Loop Lock Range Phase Detector Output Current Sinking Sourcing fOSC > fSYNC/MODE fOSC < fSYNC/MODE –3 3 µA µA Spread Spectrum Frequency Range Minimum Switching Frequency Maximum Switching Frequency 460 635 kHz kHz SYNC/MODE Pull-Down Current SYNC/MODE = 2.2V 2.6 µA PGOOD Voltage Low IPGOOD Sinking 1mA 50 mV PGOOD Trip Level VFB with Respect to Set Output Voltage VFB < 0.6V, Ramping Positive VFB < 0.6V, Ramping Negative VFB > 0.6V, Ramping Negative VFB > 0.6V, Ramping Positive PGOOD Output Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: The LTC3808E is guaranteed to meet specified performance from 0°C to 70°C. Specifications over the –40°C to 85°C operating range are assured by design characterization, and correlation with statistical process controls. Note 3: TJ is calculated from the ambient temperature TA and power dissipation PD according to the following formula: TJ = TA + (PD • θJA °C/W) –13 –16 7 10 –10.0 –13.3 10.0 13.3 –7 –10 13 16 % % % % Note 4: Dynamic supply current is higher due to gate charge being delivered at the switching frequency. Note 5: The LTC3808 is tested in a feedback loop that servos ITH to a specified voltage and measures the resultant VFB voltage. Note 6: Peak current sense voltage is reduced dependent on duty cycle to a percentage of value as shown in Figure 1. 3808f 3 LTC3808 U W TYPICAL PERFOR A CE CHARACTERISTICS Efficiency vs Load Current FIGURE 11 CIRCUIT FIGURE 11 CIRCUIT 95 VIN = 5V, VOUT = 2.5V EFFICIENCY (%) EFFICIENCY (%) VOUT = 1.2V 80 VOUT = 1.8V 75 85 BURST MODE (SYNC/MODE = VIN) 80 75 70 65 70 FORCED CONTINUOUS (SYNC/MODE = 0V) 60 65 SYNC/MODE = VIN VIN = 5V 60 1 10 100 1k LOAD CURRENT (mA) PULSE SKIPPING (SYNC/MODE = 0.6V) 55 60 40 20 0 –20 50 10k 1 Burst Mode OPERATION (ITH RISING) Burst Mode OPERATION (ITH FALLING) FORCED CONTINUOUS MODE PULSE SKIPPING MODE 80 90 VOUT = 3.3V 85 100 100 VOUT = 2.5V 95 90 Maximum Current Sense Voltage vs ITH Pin Voltage Efficiency vs Load Current CURRENT LIMIT (%) 100 TA = 25°C unless otherwise noted. 10 100 1k LOAD CURRENT (mA) 3808 G01 10k 0.5 3808 G02 Load Step (Burst Mode Operation) Load Step (Forced Continuous Mode) Load Step (Pulse Skipping Mode) VOUT 200mV/DIV AC COUPLED VOUT 200mV/DIV AC COUPLED IL 2A/DIV IL 2A/DIV IL 2A/DIV 3808 G04 100µs/DIV VIN = 3.3V VOUT = 1.8V ILOAD = 300mA TO 3A SYNC/MODE = 0V FIGURE 11 CIRCUIT Start-Up with Internal Soft-Start (TRACK/SS = VIN) 200µs/DIV VIN = 4.2V RLOAD = 1Ω FIGURE 11 CIRCUIT 3808 G07 2 3808 G03 VOUT 200mV/DIV AC COUPLED 100µs/DIV VIN = 3.3V VOUT = 1.8V ILOAD = 300mA TO 3A SYNC/MODE = VIN FIGURE 11 CIRCUIT 1 1.5 ITH VOLTAGE (V) 3808 G05 100µs/DIV VIN = 3.3V VOUT = 1.8V ILOAD = 300mA TO 3A SYNC/MODE = VFB FIGURE 11 CIRCUIT 3808 G06 Start-Up with External Soft-Start (CSS = 10nF) VOUT 1.8V VOUT 1.8V 500mV/DIV 500mV/DIV 1ms/DIV VIN = 4.2V RLOAD = 1Ω FIGURE 11 CIRCUIT 3808 G08 3808f 4 LTC3808 U W TYPICAL PERFOR A CE CHARACTERISTICS Start-Up with Coincident Tracking (VOUT = 0.8V at 0s) Start-Up with Coincident Tracking (VOUT = 0V at 0s) Vx 2.5V Vx 2.5V VOUT 1.8V VOUT 1.8V VOUT 1.8V 500mV/DIV 500mV/DIV 500mV/DIV 3808 G10 10ms/DIV VIN = 4.2V RTA = 590Ω RTB = 1.18k FIGURE 11 CIRCUIT Regulated Feedback Voltage vs Temperature Shutdown (RUN) Threshold vs Temperature 2.55 1.20 2.50 0.602 0.600 0.598 VIN RISING 1.15 2.45 RUN VOLTAGE (V) INPUT VOLTAGE (V) 0.604 2.40 2.35 2.30 VIN FALLING 1.10 1.05 2.25 0.596 3808 G11 10ms/DIV VIN = 4.2V RTA = 590Ω RTB = 1.69k FIGURE 11 CIRCUIT Undervoltage Lockout Threshold vs Temperature 0.606 2.20 0.594 20 40 60 –60 –40 –20 0 TEMPERATURE (°C) 80 100 2.15 –60 –40 –20 0 20 40 60 TEMPERATURE (°C) Maximum Current Sense Threshold vs Temperature 1.04 IPRG = FLOAT 130 125 120 115 20 40 60 –60 –40 –20 0 TEMPERATURE (°C) 100 1.00 20 40 60 –60 –40 –20 0 TEMPERATURE (°C) 80 100 3808 G14 TRACK/SS Start-Up Current vs Temperature TRACK/SS START-UP CURRENT (µA) 135 80 3808 G13 3808 G12 MAXIMUM CURRENT SENSE THRESHOLD (mV) FEEDBACK VOLTAGE (V) Start-Up with Ratiometric Tracking (VOUT = 0V at 0s) Vx 2.5V 3808 G09 10ms/DIV VIN = 4.2V RTA = 590Ω RTB = 1.18k FIGURE 11 CIRCUIT TA = 25°C unless otherwise noted. 80 100 3808 G16 TRACK/SS = 0V 1.02 1.00 0.98 0.96 0.94 20 40 60 –60 –40 –20 0 TEMPERATURE (°C) 80 100 3808 G17 3808f 5 LTC3808 U W TYPICAL PERFOR A CE CHARACTERISTICS SYNC/MODE Pull-Down Current vs Temperature Oscillator Frequency vs Temperature NORMALIZED FREQUENCY (%) 2.75 2.70 2.65 2.60 2.55 2.50 2.45 Oscillator Frequency vs Input Voltage 10 5 8 4 NORMALIZED FREQUENCY SHIFT (%) 2.80 SYNC/MODE PULL-DOWN CURRENT (µA) TA = 25°C unless otherwise noted. 6 4 2 0 –2 –4 –6 –8 2.40 –60 –40 –20 0 20 40 60 TEMPERATURE (°C) 80 –10 –60 –40 –20 0 20 40 60 TEMPERATURE (°C) 100 Shutdown Quiescent Current vs Input Voltage 10 8 6 110 100 90 4 80 2 70 9 10 3808 G21 4 7 8 5 6 INPUT VOLTAGE (V) 9 10 3808 G20 TRACK/SS STARTUP CURRENT (µA) SLEEP CURRENT (µA) 12 3 1.04 120 SHUTDOWN CURRENT (µA) 2 TRACK/SS Start-Up Current vs TRACK/SS Voltage 14 7 8 5 6 INPUT VOLTAGE (V) –4 100 16 4 –3 –5 80 130 3 –1 –2 Sleep Current vs Input Voltage 18 2 1 0 3808 G19 3808 G18 0 3 2 2 3 4 8 7 6 5 INPUT VOLTAGE (V) 1.00 0.96 0.92 0.88 0.84 9 10 3808 G22 0 0.1 0.2 0.3 0.4 0.5 TRACK/SS VOLTAGE (V) 0.6 0.7 3808 G24 3808f 6 LTC3808 U U U PI FU CTIO S (DFN/SSOP) PLLLPF (Pin 1/Pin 2): Frequency Set/PLL Lowpass Filter. When synchronizing to an external clock, this pin serves as the low pass filter point for the phase-locked loop. Normally, a series RC is connected between this pin and ground. When not synchronizing to an external clock, this pin serves as the frequency select input. Tying this pin to GND selects 300kHz operation; tying this pin to VIN selects 750kHz operation. Floating this pin selects 550kHz operation. Connect a 2.2nF capacitor between this pin and GND and a 1000pF capacitor between this pin and the SYNC/MODE when using spread spectrum modulation operation. SYNC/MODE (Pin 2/Pin 3): This pin performs four functions: 1) auxiliary winding feedback input, 2) external clock synchronization input for phase-locked loop, 3) Burst Mode, pulse skipping or forced continuous mode select, and 4) enable spread spectrum modulation operation in pulse skipping mode. Applying a clock with frequency between 250kHz to 750kHz causes the internal oscillator to phase-lock to the external clock and disables Burst Mode operation but allows pulse skipping at low load currents. To select Burst Mode operation at light loads, tie this pin to VIN. Grounding this pin selects forced continuous operation, which allows the inductor current to reverse. Tying this pin to VFB selects pulse skipping mode. In these cases, the frequency of the internal oscillator is set by the voltage on the PLLLPF pin. Tying to a voltage between 1.35V to VIN – 0.5V enables spread spectrum modulation operation. In this case, an internal 2.6µA pull-down current source helps to set the voltage at this pin by tying a resistor with appropriate value between this pin and VIN. Do not leave this pin floating. TRACK/SS (Pin 3/Pin 4): Tracking Input for the Controller or Optional External Soft-Start Input. This pin allows the start-up of VOUT to “track” the external voltage at this pin using an external resistor divider. Tying this pin to VIN allows VOUT start-up with the internal 1ms soft-start clamp. An external soft-start can be programmed by connecting a capacitor between this pin and ground. Do not leave this pin floating. PGOOD (Pin 4/Pin 5): Power Good Output Voltage Monitor Open-Drain Logic Output. This pin is pulled to ground when the voltage on the feedback pin VFB is not within ±13.3% of its nominal set point. VFB (Pin 5/Pin 6): Feedback Pin. This pin receives the remotely sensed feedback voltage for the controller from an external resistor divider across the output. ITH (Pin 6/Pin 7): Current Threshold and Error Amplifier Compensation Point. Nominal operating range on this pin is from 0.7V to 2V. The voltage on this pin determines the threshold of the main current comparator. RUN (Pin 7/Pin 8): Run Control Input. Forcing this pin below 1.1V shuts down the chip. Driving this pin to VIN or releasing this pin enables the chip to start-up either by tracking the external voltage at the TRACK/SS pin or with the internal/external soft-start, all based on the connection at the TRACK/SS pin. IPRG (Pin 8/Pin 10): Three-State Pin to Select Maximum Peak Sense Voltage Threshold. This pin selects the maximum allowed voltage drop between the SENSE+ and SENSE– or SW pins (i.e., the maximum allowed drop across the sense resistor or the external P-channel MOSFET). Tie to VIN, GND or float to select 204mV, 85mV or 125mV respectively. BG (Pin 9/Pin 11): Bottom (NMOS) Gate Drive Output. This pin drives the gate of the external N-channel MOSFET. This pin has an output swing from GND to SENSE+. TG (Pin 10/Pin 12): Top (PMOS) Gate Drive Output. This pin drives the gate of the external P-channel MOSFET. This pin has an output swing from GND to SENSE+. SENSE+ (Pin 11/Pin 13): Positive Input to Differential Current Comparator. Also powers the gate drivers. Normally connected to the source of the external P-channel MOSFET when the sense resistor is not used. Otherwise, it is connected to the sense resistor. VIN (Pin 12/Pin 14): Chip Signal Power Supply. This pin powers the entire chip except for the gate drivers. Externally filtering this pin with a lowpass RC network (e.g., R = 10Ω, C = 1µF) is suggested to minimize noise pickup, especially in high load current applications. 3808f 7 LTC3808 U U U PI FU CTIO S (DFN/SSOP) SENSE– (Pin 13/Pin 15): Negative Input to Differential Current Comparator. Normally is connected to the SW pin when the sense resistor is not used. When using a current sense resistor, connect the resistor between SENSE+ and SENSE– and connect the source of the P-channel MOSFET to the SENSE– pin. Normally this pin is connected to the drain of the external P-channel MOSFET, the drain of the external N-channel MOSFET and the inductor. GND (Pin 15/Pins 1, 9): Ground connection for internal circuits, the gate drivers and the negative input to the reverse current comparator. The exposed pad (Pin 15 in DFN package) must be soldered to the PCB ground. SW (Pin 14/Pin 16): Switch Node Connection to Inductor. This pin is also an input to the reverse current comparator. W FU CTIO AL DIAGRA U U VIN CIN VIN SENSE– SENSE+ VOLTAGE REFERENCE VREF 0.6V IPRG SLOPE CLK + UNDERVOLTAGE LOCKOUT PVIN S Q R ICMP SENSE+ – VIN BG RUN FCB VIN 0.15V SLEEP – + OV IREV TRK/SS 0.3V CLOCK DETECT 0.4V – BURSTDIS BURSTDIS FCB PHASE DETECTOR MN GND + t = 1ms INTERNAL SOFT-START SYNC/MODE BURST DEFEAT VOUT COUT SW UVSD MUX L ANTI-SHOOTTHROUGH PVIN 0.7µA 1µA MP GND SWITCHING LOGIC AND BLANKING CIRCUIT VIN TRACK/SS TG 0.68V RB + + 0.54V – VFB UV – ITH 2.6µA RC + EAMP + – PLLLPF VCO VREF 0.6V TRK/SS VFB CC RA CLK VIN 3808 FD PGOOD GND OV UV UVSD IREV + SW – GND RICMP 3808f 8 LTC3808 U OPERATIO (Refer to Functional Diagram) Main Control Loop The LTC3808 uses a constant frequency, current mode architecture. During normal operation, the top external P-channel power MOSFET is turned on when the clock sets the RS latch, and is turned off when the current comparator (ICMP) resets the latch. The peak inductor current at which ICMP resets the RS latch is determined by the voltage on the ITH pin, which is driven by the output of the error amplifier (EAMP). The VFB pin receives the output voltage feedback signal from an external resistor divider. This feedback signal is compared to the internal 0.6V reference voltage by the EAMP. When the load current increases, it causes a slight decrease in VFB relative to the 0.6V reference, which in turn causes the ITH voltage to increase until the average inductor current matches the new load current. While the top P-channel MOSFET is off, the bottom N-channel MOSFET is turned on until either the inductor current starts to reverse, as indicated by the current reversal comparator IRCMP, or the beginning of the next cycle. Shutdown, Soft-Start and Tracking Start-Up (RUN and TRACK/SS Pins) The LTC3808 is shut down by pulling the RUN pin low. In shutdown, all controller functions are disabled and the chip draws only 9µA. The TG output is held high (off) and the BG output low (off) in shutdown. Releasing the RUN pin allows an internal 0.7µA current source to pull up the RUN pin to VIN. The controller is enabled when the RUN pin reaches 1.1V. The start-up of VOUT is based on the three different connections on the TRACK/SS pin. The start-up of V OUT is controlled by the LTC3808’s internal soft-start when TRACK/SS is connected to VIN. During soft-start, the error amplifier EAMP compares the feedback signal VFB to the internal soft-start ramp (instead of the 0.6V reference), which rises linearly from 0V to 0.6V in about 1ms. This allows the output voltage to rise smoothly from 0V to its final value while maintaining control of the inductor current. The 1ms soft-start time can be changed by connecting the optional external soft-start capacitor CSS between the TRACK/SS and GND pins. When the controller is enabled by releasing the RUN pin, the TRACK/SS pin is charged up by an internal 1µA current source and rises linearly from 0V to above 0.6V. The error amplifier EAMP compares the feedback signal VFB to this ramp instead, and regulates VFB linearly from 0V to 0.6V. When the voltage on the TRACK/SS pin is less than the 0.6V internal reference, the LTC3808 regulates the VFB voltage to the TRACK/SS pin instead of the 0.6V reference. Therefore VOUT of the LTC3808 can track an external voltage VX during start-up. Typically, a resistor divider on VX is connected to the TRACK/SS pin to allow the start-up of VOUT to “track” that of VX. For coincident tracking during start-up, the regulated final value of VX should be larger than that of VOUT, and the resistor divider on VX has the same ratio as the divider on VOUT that is connected to VFB. See detailed discussions in the Run and Soft-Start/ Tracking Functions in the Applications Information Section. Light Load Operation (Burst Mode Operation, Continuous Conduction or Pulse Skipping Mode) (SYNC/MODE Pin) The LTC3808 can be programmed for either high efficiency Burst Mode operation, forced continuous conduction mode or pulse skipping mode at low load currents. To select Burst Mode operation, tie the SYNC/MODE pin to VIN. To select forced continuous operation, tie the SYNC/ MODE pin to a DC voltage below 0.4V (e.g., GND). Tying the SYNC/MODE to a DC voltage above 0.4V and below 1.2V (e.g., VFB) enables pulse skipping mode. The 0.4V threshold between forced continuous operation and pulse skipping mode can be used in secondary winding regulation as described in the Auxiliary Winding Control Using SYNC/MODE Pin discussion in the Applications Information section. When the LTC3808 is in Burst Mode operation, the peak current in the inductor is set to approximate one-fourth of the maximum sense voltage even though the voltage on the ITH pin indicates a lower value. If the average inductor current is higher than the load current, the EAMP will decrease the voltage on the ITH pin. When the ITH voltage drops below 0.85V, the internal SLEEP signal goes high and the external MOSFET is turned off. 3808f 9 LTC3808 U OPERATIO (Refer to Functional Diagram) In sleep mode, much of the internal circuitry is turned off, reducing the quiescent current that the LTC3808 draws. The load current is supplied by the output capacitor. As the output voltage decreases, the EAMP increases the ITH voltage. When the ITH voltage reaches 0.925V, the SLEEP signal goes low and the controller resumes normal operation by turning on the external P-channel MOSFET on the next cycle of the internal oscillator. When the controller is enabled for Burst Mode or pulse skipping operation, the inductor current is not allowed to reverse. Hence, the controller operates discontinuously. The reverse current comparator RICMP senses the drainto-source voltage of the bottom external N-channel MOSFET. This MOSFET is turned off just before the inductor current reaches zero, preventing it from going negative. In forced continuous operation, the inductor current is allowed to reverse at light loads or under large transient conditions. The peak inductor current is determined by the voltage on the ITH pin. The P-channel MOSFET is turned on every cycle (constant frequency) regardless of the ITH pin voltage. In this mode, the efficiency at light loads is lower than in Burst Mode operation. However, continuous mode has the advantages of lower output ripple and no noise at audio frequencies. When the SYNC/MODE pin is clocked by an external clock source to use the phase-locked loop (see Frequency Selection and Phase-Locked Loop), or is set to a DC voltage between 0.4V and several hundred mV below VIN, the LTC3808 operates in PWM pulse skipping mode at light loads. In this mode, the current comparator ICMP may remain tripped for several cycles and force the external P-channel MOSFET to stay off for the same number of cycles. The inductor current is not allowed to reverse (discontinuous operation). This mode, like forced continuous operation, exhibits low output ripple as well as low audio noise and reduced RF interference as compared to Burst Mode operation. However, it provides low current efficiency higher than forced continuous mode, but not nearly as high as Burst Mode operation. During start-up or an undervoltage condition (VFB ≤ 0.54V), the LTC3808 operates in pulse skipping mode (no current reversal allowed), regardless of the state of the SYNC/MODE pin. Short-Circuit and Current Limit Protection The LTC3808 monitors the voltage drop ∆VSC (between the GND and SW pins) across the external N-channel MOSFET with the short-circuit current limit comparator. The allowed voltage is determined by: ∆VSC(MAX) = A • 90mV where A is a constant determined by the state of the IPRG pin. Floating the IPRG pin selects A = 1; tying IPRG to VIN selects A = 5/3; tying IPRG to GND selects A = 2/3. The inductor current limit for short-circuit protection is determined by ∆VSC(MAX) and the on-resistance of the external N-channel MOSFET: ISC = ∆VSC(MAX) RDS(ON) Once the inductor current exceeds ISC, the short current comparator will shut off the external P-channel MOSFET until the inductor current drops below ISC. Output Overvoltage Protection As further protection, the overvoltage comparator (OVP) guards against transient overshoots, as well as other more serious conditions that may overvoltage the output. When the feedback voltage on the VFB pin has risen 13.33% above the reference voltage of 0.6V, the external P-channel MOSFET is turned off and the N-channel MOSFET is turned on until the overvoltage is cleared. Frequency Selection and Phase-Locked Loop (PLLLPF and SYNC/MODE Pins) The selection of switching frequency is a tradeoff between efficiency and component size. Low frequency operation increases efficiency by reducing MOSFET switching losses, but requires larger inductance and/or capacitance to maintain low output ripple voltage. The switching frequency of the LTC3808’s controllers can be selected using the PLLLPF pin. If the SYNC/MODE is not being driven by an external clock source, the PLLLPF can be floated, tied to VIN or tied to GND to select 550kHz, 750kHz or 300kHz, respectively. 3808f 10 LTC3808 U OPERATIO (Refer to Functional Diagram) A phase-locked loop (PLL) is available on the LTC3808 to synchronize the internal oscillator to an external clock source that connects to the SYNC/MODE pin. In this case, a series RC should be connected between the PLLLPF pin and GND to serve as the PLL’s loop filter. The LTC3808 phase detector adjusts the voltage on the PLLLPF pin to align the turn-on of the external P-channel MOSFET to the rising edge of the synchronizing signal. The typical capture range of the LTC3808’s phase-locked loop is from approximately 200kHz to 1MHz. Spread Spectrum Modulation (SYNC/MODE and PLLLPF Pins) Connecting the SYNC/MODE pin to a DC voltage above 1.35V and several hundred mV below VIN enables spread spectrum modulation (SSM) operation. An internal 2.6µA pull-down current source at SYNC/MODE helps to set the voltage at the SYNC/MODE pin for this operation by tying a resistor with appropriate value between SYNC/MODE and VIN. This mode of operation spreads the internal oscillator frequency fOSC (= 550kHz) over a wider range (460kHz to 635kHz), reducing the peaks of the harmonic output on a spectral analysis of the output noise. In this case, a 2.2nF filter cap should be connected between the PLLLPF pin and GND and another 1000pF cap should be connected between PLLLPF and the SYNC/MODE pin. The controller operates in PWM pulse skipping mode at light loads when spread spectrum modulation is selected. See more discussions in the Spread Spectrum Modulation with SYNC/MODE and PLLLPF Pins in the Applications Information section. Dropout Operation When the input supply voltage (VIN) approaches the output voltage, the rate of change of the inductor current while the external P-channel MOSFET is on (ON cycle) decreases. This reduction means that the P-channel MOSFET will remain on for more than one oscillator cycle if the inductor current has not ramped up to the threshold set by the EAMP on the ITH pin. Further reduction in the input supply voltage will eventually cause the P-channel MOSFET to be turned on 100%; i.e., DC. The output voltage will then be determined by the input voltage minus the voltage drop across the P-channel MOSFET and the inductor. Undervoltage Lockout To prevent operation of the P-channel MOSFET below safe input voltage levels, an undervoltage lockout is incorporated in the LTC3808. When the input supply voltage (VIN) drops below 2.25V, the external P- and N-channel MOSFETs and all internal circuits are turned off except for the undervoltage block, which draws only a few microamperes. Peak Current Sense Voltage Selection and Slope Compensation (IPRG Pin) When the LTC3808 controller is operating below 20% duty cycle, the peak current sense voltage (between the SENSE+ and SENSE–/SW pins) allowed across the external Pchannel MOSFET is determined by: ∆VSENSE(MAX) = A • VITH – 0.7 V 10 where A is a constant determined by the state of the IPRG pin. Floating the IPRG pin selects A = 1; tying IPRG to VIN selects A = 5/3; tying IPRG to GND selects A = 2/3. The 3808f 11 LTC3808 U OPERATIO (Refer to Functional Diagram) maximum value of VITH is typically about 1.98V, so the maximum sense voltage allowed across the external P-channel MOSFET is 125mV, 85mV or 204mV for the three respective states of the IPRG pin. However, once the controller’s duty cycle exceeds 20%, slope compensation begins and effectively reduces the peak sense voltage by a scale factor (SF) given by the curve in Figure 1. The peak inductor current is determined by the peak sense voltage and the on-resistance of the external P-channel MOSFET: IPK = ∆VSENSE(MAX) RDS(ON) If a sense resistor is used, ∆VSENSE(MAX) is the peak current sense voltage (between the SENSE+ and SENSE– pins) across the sense resistor. The peak inductor is determined by the peak sense voltage and the resistance of the sense resistor: IPK = ∆VSENSE(MAX) RSENSE Power Good (PGOOD) Pin A window comparator monitors the feedback voltage and the open-drain PGOOD output pin is pulled low when the feedback voltage is not within ±10% of the 0.6V reference voltage. PGOOD is low when the LTC3808 is shut down or in undervoltage lockout. 110 100 90 SF = I/IMAX (%) 80 70 60 50 40 30 20 10 0 0 10 20 30 40 50 60 70 80 90 100 DUTY CYCLE (%) 3808 F01 Figure 1. Maximum Peak Current vs Duty Cycle 3808f 12 LTC3808 U W U U APPLICATIO S I FOR ATIO The typical LTC3808 application circuit is shown on Figure 11. External component selection for the controller is driven by the load requirement and begins with the selection of the inductor and the power MOSFETs. Power MOSFET Selection The LTC3808’s controller requires two external power MOSFETs: a P-channel MOSFET for the topside (main) switch and a N-channel MOSFET for the bottom (synchronous) switch. The main selection criteria for the power MOSFETs are the breakdown voltage VBR(DSS), threshold voltage VGS(TH), on-resistance RDS(ON), reverse transfer capacitance CRSS, turn-off delay tD(OFF) and the total gate charge QG. The gate drive voltage is the input supply voltage. Since the LTC3808 is designed for operation down to low input voltages, a sublogic level MOSFET (RDS(ON) guaranteed at VGS = 2.5V) is required for applications that work close to this voltage. When these MOSFETs are used, make sure that the input supply to the LTC3808 is less than the absolute maximum MOSFET VGS rating, which is typically 8V. The P-channel MOSFET’s on-resistance is chosen based on the required load current. The maximum average load current IOUT(MAX) is equal to the peak inductor current minus half the peak-to-peak ripple current IRIPPLE. The LTC3808’s current comparator monitors the drain-tosource voltage VDS of the top P-channel MOSFET, which is sensed between the SENSE+ and SW pins. The peak inductor current is limited by the current threshold, set by the voltage on the ITH pin, of the current comparator. The voltage on the ITH pin is internally clamped, which limits the maximum current sense threshold ∆VSENSE(MAX) to approximately 125mV when IPRG is floating (85mV when IPRG is tied low; 204mV when IPRG is tied high). The output current that the LTC3808 can provide is given by: IOUT(MAX) = ∆VSENSE(MAX) IRIPPLE – RDS(ON) 2 where IRIPPLE is the inductor peak-to-peak ripple current (see Inductor Value Calculation). A reasonable starting point is setting ripple current IRIPPLE to be 40% of IOUT(MAX). Rearranging the above equation yields: RDS(ON)MAX = 5 ∆VSENSE(MAX) • for Duty Cycle < 20% 6 IOUT(MAX) However, for operation above 20% duty cycle, slope compensation has to be taken into consideration to select the appropriate value of RDS(ON) to provide the required amount of load current: RDS(ON)MAX = ∆VSENSE(MAX) 5 • SF • 6 IOUT(MAX) where SF is a scale factor whose value is obtained from the curve in Figure 1. These must be further derated to take into account the significant variation in on-resistance with temperature. The following equation is a good guide for determining the required RDS(ON)MAX at 25°C (manufacturer’s specification), allowing some margin for variations in the LTC3808 and external component values: RDS(ON)MAX = ∆VSENSE(MAX) 5 • 0.9 • SF • 6 IOUT(MAX) • ρT The ρT is a normalizing term accounting for the temperature variation in on-resistance, which is typically about 0.4%/°C, as shown in Figure 2. Junction-to-case temperature TJC is about 10°C in most applications. For a maximum ambient temperature of 70°C, using ρ80°C ~ 1.3 in the above equation is a reasonable choice. The N-channel MOSFET’s on resistance is chosen based on the short-circuit current limit (ISC). The LTC3808’s short-circuit current limit comparator monitors the drainto-source voltage VDS of the bottom N-channel MOSFET, 3808f 13 LTC3808 U W U U APPLICATIO S I FOR ATIO ρT NORMALIZED ON RESISTANCE 2.0 VOUT VIN V –V Bottom N-Channel Duty Cycle = IN OUT VIN Top P-Channel Duty Cycle = 1.5 1.0 The MOSFET power dissipations at maximum output current are: 0.5 PTOP = 0 – 50 50 100 0 JUNCTION TEMPERATURE (°C) 150 3808 F02 Figure 2. RDS(ON) vs Temperature which is sensed between the GND and SW pins. The shortcircuit current sense threshold ∆VSC is set approximately 90mV when IPRG is floating (60mV when IPRG is tied low; 150mV when IPRG is tied high). The on-resistance of Nchannel MOSFET is determined by: RDS(ON)MAX = ∆VSC ISC(PEAK) The short-circuit current limit (ISC(PEAK)) should be larger than the IOUT(MAX) with some margin to avoid interfering with the peak current sensing loop. On the other hand, in order to prevent the MOSFETs from excessive heating and the inductor from saturation, ISC(PEAK) should be smaller than the minimum value of their current ratings. A reasonable range is: IOUT(MAX) < ISC(PEAK) < IRATING(MIN) Therefore, the on-resistance of N-channel MOSFET should be chosen within the following range: ∆VSC IRATING(MIN) < RDS(ON) < ∆VSC IOUT(MAX) where ∆VSC is 90mV, 60mV or 150mV with IPRG being floated, tied to GND or VIN respectively. The power dissipated in the MOSFET strongly depends on its respective duty cycles and load current. When the LTC3808 is operating in continuous mode, the duty cycles for the MOSFETs are: PBOT = VOUT • IOUT (MAX)2 • ρT • RDS(ON) + 2 • VIN2 VIN • IOUT (MAX) • C RSS • f VIN – VOUT • IOUT (MAX)2 • ρT • RDS(ON) VIN Both MOSFETs have I2R losses and the PTOP equation includes an additional term for transition losses, which are largest at high input voltages. The bottom MOSFET losses are greatest at high input voltage or during a short-circuit when the bottom duty cycle is 100%. The LTC3808 utilizes a non-overlapping, anti-shootthrough gate drive control scheme to ensure that the Pand N-channel MOSFETs are not turned on at the same time. To function properly, the control scheme requires that the MOSFETs used are intended for DC/DC switching applications. Many power MOSFETs, particularly P-channel MOSFETs, are intended to be used as static switches and therefore are slow to turn on or off. Reasonable starting criteria for selecting the P-channel MOSFET are that it must typically have a gate charge (QG) less than 25nC to 30nC (at 4.5VGS) and a turn-off delay (tD(OFF)) of less than approximately 140ns. However, due to differences in test and specification methods of various MOSFET manufacturers, and in the variations in QG and tD(OFF) with gate drive (VIN) voltage, the P-channel MOSFET ultimately should be evaluated in the actual LTC3808 application circuit to ensure proper operation. Shoot-through between the P-channel and N-channel MOSFETs can most easily be spotted by monitoring the input supply current. As the input supply voltage increases, if the input supply current increases dramatically, then the likely cause is shoot-through. Note that some MOSFETs that do not work well at high input voltages (e.g., 3808f 14 LTC3808 U W U U APPLICATIO S I FOR ATIO VIN > 5V) may work fine at lower voltages (e.g., 3.3V). Selecting the N-channel MOSFET is typically easier, since for a given RDS(ON), the gate charge and turn-on and turnoff delays are much smaller than for a P-channel MOSFET. Using a Sense Resistor A sense resistor RSENSE can be connected between SENSE+ and SENSE– to sense the output load current. In this case, the source of the P-channel MOSFET is connected to SENSE– pin and the drain is connected to SW pin of LTC3808. Therefore the current comparator monitors the voltage developed across RSENSE instead of VDS of the P-channel MOSFET. The output current that the LTC3808 can provide in this case is given by: ∆VSENSE(MAX) IRIPPLE IOUT(MAX) = – RSENSE 2 Setting ripple current as 40% of IOUT(MAX) and using Figure 1 to choose SF, the value of RSENSE is: RSENSE = ∆VSENSE(MAX) 5 • SF • 6 IOUT(MAX) See the P-channel RDS(ON) selection in Power MOSFET Selection. Variation in the resistance of a sense resistor is much smaller than the variation in on-resistance of the external MOSFET. Therefore the load current is well controlled with a sense resistor. However the sense resistor causes extra I2R losses in addition to the I2R losses of the MOSFET. Therefore, using a sense resistor lowers the efficiency of LTC3808, especially for large load current. Operating Frequency and Synchronization The choice of operating frequency, fOSC, is a trade-off between efficiency and component size. Low frequency operation improves efficiency by reducing MOSFET switching losses, both gate charge loss and transition loss. However, lower frequency operation requires more inductance for a given amount of ripple current. The internal oscillator for the LTC3808’s controller runs at a nominal 550kHz frequency when the PLLLPF pin is left floating and the SYNC/MODE pin is not configured for spread spectrum operation. Pulling the PLLLPF to VIN selects 750kHz operation; pulling the PLLLPF to GND selects 300kHz operation. Alternatively, the LTC3808 will phase-lock to a clock signal applied to the SYNC/MODE pin with a frequency between 250kHz and 750kHz (see Phase-Locked Loop and Frequency Synchronization). To further reduce EMI, the nominal 550kHz frequency will be spread over a range with frequencies between 460kHz and 635kHz when spread spectrum modulation is enabled (see Spread Spectrum Modulation with SYNC/MODE and PLLLPF Pins). Inductor Value Calculation Given the desired input and output voltages, the inductor value and operating frequency, fOSC, directly determine the inductor’s peak-to-peak ripple current: IRIPPLE = VOUT VIN – VOUT • VIN fOSC • L Lower ripple current reduces core losses in the inductor, ESR losses in the output capacitors and output voltage ripple. Thus, highest efficiency operation is obtained at low frequency with a small ripple current. Achieving this, however, requires a large inductor. A reasonable starting point is to choose a ripple current that is about 40% of IOUT(MAX). Note that the largest ripple current occurs at the highest input voltage. To guarantee that ripple current does not exceed a specified maximum, the inductor should be chosen according to: L≥ VIN – VOUT VOUT • fOSC • IRIPPLE VIN Burst Mode Operation Considerations The choice of RDS(ON) and inductor value also determines the load current at which the LTC3808 enters Burst Mode operation. When bursting, the controller clamps the peak inductor current to approximately: IBURST(PEAK) = 1 ∆VSENSE(MAX) • 4 RDS(ON) 3808f 15 LTC3808 U W U U APPLICATIO S I FOR ATIO The corresponding average current depends on the amount of ripple current. Lower inductor values (higher IRIPPLE) will reduce the load current at which Burst Mode operation begins. inductors wound on bobbins are generally easier to surface mount. However, designs for surface mount that do not increase the height significantly are available from Coiltronics, Coilcraft, Dale and Sumida. The ripple current is normally set so that the inductor current is continuous during the burst periods. Therefore, Schottky Diode Selection (Optional) IRIPPLE ≤ IBURST(PEAK) This implies a minimum inductance of: LMIN ≤ VIN – VOUT V • OUT fOSC • IBURST(PEAK) VIN A smaller value than LMIN could be used in the circuit, although the inductor current will not be continuous during burst periods, which will result in slightly lower efficiency. In general, though, it is a good idea to keep IRIPPLE comparable to IBURST(PEAK). Inductor Core Selection Once the value of L is known, the type of inductor must be selected. High efficiency converters generally cannot afford the core loss found in low cost powdered iron cores, forcing the use of more expensive ferrite, molypermalloy or Kool Mµ® cores. Actual core loss is independent of core size for a fixed inductor value, but is very dependent on the inductance selected. As inductance increases, core losses go down. Unfortunately, increased inductance requires more turns of wire and therefore copper losses will increase. Ferrite designs have very low core losses and are preferred at high switching frequencies, so design goals can concentrate on copper loss and preventing saturation. Ferrite core material saturates “hard”, which means that inductance collapses abruptly when the peak design current is exceeded. Core saturation results in an abrupt increase in inductor ripple current and consequent output voltage ripple. Do not allow the core to saturate! Molypermalloy (from Magnetics, Inc.) is a very good, low loss core material for toroids, but is more expensive than ferrite. A reasonable compromise from the same manufacturer is Kool Mµ. Toroids are very space efficient, especially when several layers of wire can be used, while The schottky diode D in Figure 12 conducts current during the dead time between the conduction of the power MOSFETs. This prevents the body diode of the bottom N-channel MOSFET from turning on and storing charge during the dead time, which could cost as much as 1% in efficiency. A 1A Schottky diode is generally a good size for most LTC3808 applications, since it conducts a relatively small average current. Larger diode results in additional transition losses due to its larger junction capacitance. This diode may be omitted if the efficiency loss can be tolerated. CIN and COUT Selection In continuous mode, the source current of the P-channel MOSFET is a square wave of duty cycle (VOUT/VIN). To prevent large voltage transients, a low ESR input capacitor sized for the maximum RMS current must be used. The maximum RMS capacitor current is given by: 1/ 2 VOUT • ( VIN – VOUT ) CIN Re quiredIRMS ≈ IMAX • VIN This formula has a maximum value at VIN = 2VOUT, where IRMS = IOUT/2. This simple worst-case condition is commonly used for design because even significant deviations do not offer much relief. Note that capacitor manufacturer’s ripple current ratings are often based on 2000 hours of life. This makes it advisable to further derate the capacitor or to choose a capacitor rated at a higher temperature than required. Several capacitors may be paralleled to meet the size or height requirements in the design. Due to the high operating frequency of the LTC3808, ceramic capacitors can also be used for CIN. Always consult the manufacturer if there is any question. The selection of COUT is driven by the effective series resistance (ESR). Typically, once the ESR requirement is Kool Mµ is a registered trademark of Magnetics, Inc. 3808f 16 LTC3808 U W U U APPLICATIO S I FOR ATIO satisfied, the capacitance is adequate for filtering. The output ripple (∆VOUT) is approximated by: 3.3V OR 5V LTC3808 RUN LTC3808 RUN ⎛ ⎞ 1 ∆VOUT ≈ IRIPPLE • ⎜ ESR + ⎟ ⎝ 8 • f • C OUT ⎠ where f is the operating frequency, COUT is the output capacitance and IRIPPLE is the ripple current in the inductor. The output ripple is highest at maximum input voltage since IRIPPLE increase with input voltage. Setting Output Voltage The LTC3808 output voltage is set by an external feedback resistor divider carefully placed across the output, as shown in Figure 3. The regulated output voltage is determined by: ⎛ R ⎞ VOUT = 0.6 V • ⎜ 1 + B ⎟ ⎝ RA ⎠ Figure 4. RUN Pin Interfacing Once the controller is enabled, the start-up of VOUT is controlled by the state of the TRACK/SS pin. If the TRACK/ SS pin is connected to VIN, the start-up of VOUT is controlled by internal soft-start, which slowly ramps the positive reference to the error amplifier from 0V to 0.6V, allowing VOUT to rise smoothly from 0V to its final value. The default internal soft-start time is around 1ms. The soft-start time can be changed by placing a capacitor between the TRACK/SS pin and GND. In this case, the softstart time will be approximately: tSS = CSS • For most applications, a 59k resistor is suggested for RA. In applications where minimizing the quiescent current is critical, RA should be made bigger to limit the feedback divider current. If RB then results in very high impedance, it may be beneficial to bypass RB with a 50pF to 100pF capacitor CFF. VOUT LTC3808 3808 F04 RB CFF VFB RA 3808 F03 Figure 3. Setting Output Voltage Run and Soft-Start/Tracking Functions The LTC3808 has a low power shutdown mode which is controlled by the RUN pin. Pulling the RUN pin below 1.1V puts the LTC3808 into a low quiescent current shutdown mode (IQ = 9µA). Releasing the RUN pin, an internal 0.7µA (at VIN = 4.2V) current source will pull the RUN pin up to VIN, which enables the controller. The RUN pin can be driven directly from logic as showed in Figure 4. 600mV 1µA where 1µA is an internal current source which is always on. When the voltage on the TRACK/SS pin is less than the internal 0.6V reference, the LTC3808 regulates the VFB voltage to the TRACK/SS pin voltage instead of 0.6V. Therefore the start-up of VOUT can ratiometrically track an external voltage VX, according to a ratio set by a resistor divider at TRACK/SS pin (Figure 5a). The ratiometric relation between VOUT and VX is (Figure 5c): VOUT RTA RA + RB = • VX RA RTA + RTB VOUT VX LTC3808 RTB RB VFB TRACK/SS RA RTA 3808 F5a Figure 5a. Using the TRACK/SS Pin to Track VX 3808f 17 LTC3808 U W U U APPLICATIO S I FOR ATIO VOUT VX OUTPUT VOLTAGE OUTPUT VOLTAGE VX VOUT 3808 F05b,c TIME TIME (5b) Coincident Tracking (5c) Ratiometric Tracking Figure 5b and 5c. Two Different Modes of Output Voltage Tracking RTA = RA, RTB = RB VX should always be greater than VOUT when using the tracking function of TRACK/SS pin. The internal current source (1µA), which is for external soft-start, will cause a tracking error at VOUT. For example, if a 59k resistor is chosen for RTA, the RTA current will be about 10µA (600mV/59k). In this case, the 1µA internal current source will cause about 10% (1µA/10µA • 100%) tracking error, which is about 60mV (600mV • 10%) referred to VFB. This is acceptable for most applications. If a better tracking accuracy is required, the value of RTA should be reduced. Table 1 summarizes the different states in which the TRACK/SS can be used. Table 1. The States of the TRACK/SS Pin TRACK/SS Pin FREQUENCY Capacitor CSS External Soft-Start VIN Internal Soft-Start Resistor Divider VOUT Tracking an External Voltage VX is an edge sensitive digital type that provides zero degrees phase shift between the external and internal oscillators. This type of phase detector does not exhibit false lock to harmonics of the external clock. The output of the phase detector is a pair of complementary current sources that charge or discharge the external filter network connected to the PLLLPF pin. The relationship between the voltage on the PLLLPF pin and operating frequency, when there is a clock signal applied to SYNC/ MODE, is shown in Figure 6 and specified in the electrical characteristics table. Note that the LTC3808 can only be synchronized to an external clock whose frequency is within range of the LTC3808’s internal VCO, which is 1200 1000 FREQUENCY (kHz) For coincident tracking (VOUT = VX during start-up), 800 600 400 200 Phase-Locked Loop and Frequency Synchronization 0 0.2 The LTC3808 has a phase-locked loop (PLL) comprised of an internal voltage-controlled oscillator (VCO) and a phase detector. This allows the turn-on of the external P-channel MOSFET to be locked to the rising edge of an external clock signal applied to the SYNC/MODE pin. The phase detector 0.7 1.2 1.7 PLLLPF PIN VOLTAGE (V) 2.2 3808 F06 Figure 6. Relationship Between Oscillator Frequency and Voltage at the PLLLPF Pin When Synchronizing to an External Clock 3808f 18 LTC3808 U W U U APPLICATIO S I FOR ATIO Table 2. The States of the PLLLPF Pin 2.4V RLP PLLLPF PIN SYNC/MODE PIN FREQUENCY 0V DC Voltage (<1.2V or VIN) 300kHz Floating DC Voltage (<1.2V or VIN) 550kHz VIN DC Voltage (<1.2V or VIN) 750kHz CLP SYNC/ MODE EXTERNAL OSCILLATOR PLLLPF DIGITAL PHASE/ FREQUENCY DETECTOR OSCILLATOR RC Loop Filter Clock Signal Phase-Locked to External Clock Filter Caps Spread Spectrum 460kHz to 635kHz DC Voltage (>1.35V and <VIN – 0.5V) 3808 F07 Figure 7. Phase-Locked Loop Block Diagram nominally 200kHz to 1MHz. This is guaranteed, over temperature and process variations, to be between 250kHz and 750kHz. A simplified block diagram is shown in Figure 7. If the external clock frequency is greater than the internal oscillator’s frequency, fOSC, then current is sourced continuously from the phase detector output, pulling up the PLLLPF pin. When the external clock frequency is less than fOSC, current is sunk continuously, pulling down the PLLLPF pin. If the external and internal frequencies are the same but exhibit a phase difference, the current sources turn on for an amount of time corresponding to the phase difference. The voltage on the PLLLPF pin is adjusted until the phase and frequency of the internal and external oscillators are identical. At the stable operating point, the phase detector output is high impedance and the filter capacitor CLP holds the voltage. The loop filter components, CLP and RLP, smooth out the current pulses from the phase detector and provide a stable input to the voltage-controlled oscillator. The filter components CLP and RLP determine how fast the loop acquires lock. Typically RLP = 10k and CLP is 2200pF to 0.01µF. Typically, the external clock (on SYNC/MODE pin) input high level is 1.6V, while the input low level is 1.2V. Table 2 summarizes the different states in which the PLLLPF pin can be used. Auxiliary Winding Control Using SYNC/MODE Pin The SYNC/MODE pin can be used as an auxiliary feedback to provide a means of regulating a flyback winding output. When this pin drops below its ground-referenced 0.4V threshold, continuous mode operation is forced. During continuous mode, current flows continuously in the transformer primary side. The auxiliary winding draws current only when the bottom synchronous N-channel MOSFET is on. When primary load currents are low and/ or the VIN/VOUT ratio is close to unity, the synchronous MOSFET may not be on for a sufficient amount of time to transfer power from the output capacitor to the auxiliary load. Forced continuous operation will support an auxiliary winding as long as there is a sufficient synchronous MOSFET duty factor. The SYNC/MODE input pin removes the requirement that power must be drawn from the transformer primary side in order to extract power from the auxiliary winding. With the loop in continuous mode, the auxiliary output may nominally be loaded without regard to the primary output load. The auxiliary output voltage VAUX is normally set, as shown in Figure 8, by the turns ratio N of the transformer: VAUX = (N + 1) • VOUT VIN LTC3808 R6 TG VAUX + L1 1:N 1µF VOUT SYNC/MODE R5 SW BG + COUT 3808 F08 Figure 8. Auxiliary Output Loop Connection 3808f 19 LTC3808 U W U U APPLICATIO S I FOR ATIO However, if the controller goes into pulse skipping operation and halts switching due to a light primary load current, then VAUX will droop. An external resistor divider from VAUX to the SYNC/MODE sets a minimum voltage VAUX(MIN): ⎛ R6 ⎞ VAUX(MIN) = 0.4V • ⎜ 1 + ⎟ ⎝ R5 ⎠ If VAUX drops below this value, the SYNC/MODE voltage forces temporary continuous switching operation until VAUX is again above its minimum. Spread Spectrum Modulation with SYNC/MODE and PLLLPF Pins Switching regulators, which operate at fixed frequency, conduct electromagnetic interference (EMI) to their downstream load(s) with high spectral power density at this fundamental and harmonic frequencies. The peak energy can be lowered and distributed to other frequencies and their harmonics by modulating the PWM frequency. The LTC3808’s switching noise (at 550kHz) is spread between VOUT Spectrum without Spread Spectrum Modulation NOISE (dBm) –10dBm/DIV 460kHz and 635kHz in spread spectrum modulation operation. Figure 9 shows the spectral plots of the output (VOUT) noise with/without spread spectrum modulation. Note the significant reduction in peak output noise (>20dBm). The spread spectrum modulation operation of the LTC3808 is enabled by setting SYNC/MODE pin to a DC voltage between 1.35V and several hundred mV below VIN by tying a resistor between SYNC/MODE and VIN. Table 3 summarizes the different states in which the SYNC/MODE Pin can be used. Table 3. The States of the SYNC/MODE Pin SYNC/MODE PIN CONDITION GND (0V to 0.35V) Forced Continuous Mode Current Reversal Allowed VFB (0.45V to 1.2V) Pulse Skipping Mode No Current Reversal Allowed Resistor to VIN (1.35V to VIN – 0.5V) Spread Spectrum Modulation Pulse Skipping at Light Loads No Current Reversal Allowed VIN Burst Mode Operation No Current Reversal Allowed Feedback Resistors Regulate an Auxiliary Winding External Clock Signal Enable Phase-Locked Loop (Synchronize to External Clock) Pulse Skipping at Light Load No Current Reversal Allowed Fault Condition: Short-Circuit and Current Limit START FREQ: 400kHz RBW: 100Hz STOP FREQ: 700kHz 3808 F09a VOUT Spectrum with Spread Spectrum Modulation (CSSM = 2200pF) NOISE (dBm) –10dBm/DIV START FREQ: 400kHz RBW: 100Hz STOP FREQ: 700kHz 3808 F09b If the LTC3808’s load current exceeds the short-circuit current limit (ISC), which is set by the short-circuit sense threshold (∆VSC) and the on resistance (RDS(ON)) of bottom N-channel MOSFET, the top P-channel MOSFET is turned off and will not be turned on at the next clock cycle unless the load current decreases below ISC. In this case, the controller’s switching frequency is decreased and the output is regulated by short-circuit (current limit) protection. In a hard short (VOUT = 0V), the top P-channel MOSFET is turned off and kept off until the short-circuit condition is cleared. In this case, there is no current path from input supply (VIN) to either VOUT or GND, which prevents excessive MOSFET and inductor heating. Figure 9. Spectral Response of Spread Spectrum Modulation 3808f 20 LTC3808 U W U U APPLICATIO S I FOR ATIO NORMALIZED VOLTAGE OR CURRENT (%) 105 100 95 Efficiency Considerations VREF The efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine what is limiting efficiency and which change would produce the most improvement. Efficiency can be expressed as: MAXIMUM SENSE VOLTAGE 90 85 Efficiency = 100% – (L1 + L2 + L3 + …) 80 75 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 INPUT VOLTAGE (V) 3808 F10 Figure 10. Line Regulation of VREF and Maximum Sense Voltage Low Input Supply Voltage Although the LTC3808 can function down to below 2.4V, the maximum allowable output current is reduced as VIN decreases below 3V. Figure 10 shows the amount of change as the supply is reduced down to 2.4V. Also shown is the effect on VREF. Minimum On-Time Considerations Minimum on-time, tON(MIN) is the smallest amount of time that the LTC3808 is capable of turning the top P-channel MOSFET on. It is determined by internal timing delays and the gate charge required to turn on the top MOSFET. Low duty cycle and high frequency applications may approach the minimum on-time limit and care should be taken to ensure that: tON(MIN) < VOUT fOSC • VIN If the duty cycle falls below what can be accommodated by the minimum on-time, the LTC3808 will begin to skip cycles (unless forced continuous mode is selected). The output voltage will continue to be regulated, but the ripple current and ripple voltage will increase. The minimum ontime for the LTC3808 is typically about 210ns. However, as the peak sense voltage (IL(PEAK) • RDS(ON)) decreases, the minimum on-time gradually increases up to about 260ns. This is of particular concern in forced continuous applications with low ripple current at light loads. If forced continuous mode is selected and the duty cycle falls below the minimum on time requirement, the output will be regulated by overvoltage protection. where L1, L2, etc. are the individual losses as a percentage of input power. Although all dissipative elements in the circuit produce losses, four main sources usually account for most of the losses in LTC3808 circuits: 1) LTC3808 DC bias current, 2) MOSFET gate charge current, 3) I2R losses and 4) transition losses. 1) The VIN (pin) current is the DC supply current, given in the Electrical Characteristics, which excludes MOSFET driver currents. VIN current results in a small loss that increases with VIN. 2) MOSFET gate charge current results from switching the gate capacitance of the power MOSFET. Each time a MOSFET gate is switched from low to high to low again, a packet of charge dQ moves from SENSE+ to ground. The resulting dQ/dt is a current out of SENSE+, which is typically much larger than the DC supply current. In continuous mode, IGATECHG = f • QP. 3) I2R losses are calculated from the DC resistances of the MOSFETs, inductor and/or sense resistor. In continuous mode, the average output current flows through L but is “chopped” between the top P-channel MOSFET and the bottom N-channel MOSFET. The MOSFET RDS(ON) and/or the resistance of the sense resistor multiplied by duty cycle can be summed with the resistance of L to obtain I2R losses. 4) Transition losses apply to the external MOSFET and increase with higher operating frequencies and input voltages. Transition losses can be estimated from: Transition Loss = 2 • VIN2 • IO(MAX) • CRSS • f Other losses, including CIN and COUT ESR dissipative losses and inductor core losses, generally account for less than 2% total additional loss. 3808f 21 LTC3808 U W U U APPLICATIO S I FOR ATIO Checking Transient Response The regulator loop response can be checked by looking at the load transient response. Switching regulators take several cycles to respond to a step in load current. When a load step occurs, VOUT immediately shifts by an amount equal to (∆ILOAD) • (ESR), where ESR is the effective series resistance of COUT. ∆ILOAD also begins to charge or discharge COUT generating a feedback error signal used by the regulator to return VOUT to its steady-state value. During this recovery time, VOUT can be monitored for overshoot or ringing that would indicate a stability problem. OPTI-LOOP compensation allows the transient response to be optimized over a wide range of output capacitance and ESR values. The ITH series RC-CC filter (see Functional Diagram) sets the dominant pole-zero loop compensation. The ITH external components showed in the figure on the first page of this data sheet will provide adequate compensation for most applications. The values can be modified slightly (from 0.2 to 5 times their suggested values) to optimize transient response once the final PC layout is done and the particular output capacitor type and value have been determined. The output capacitor needs to be decided upon because the various types and values determine the loop feedback factor gain and phase. An output current pulse of 20% to 100% of full load current having a rise time of 1µs to 10µs will produce output voltage and ITH pin waveforms that will give a sense of the overall loop stability. The gain of the loop will be increased by increasing RC and the bandwidth of the loop will be increased by decreasing CC. The output voltage settling behavior is related to the stability of the closed-loop system and will demonstrate the actual overall supply performance. For a detailed explanation of optimizing the compensation com- ponents, including a review of control loop theory, refer to Application Note 76. A second, more severe transient is caused by switching in loads with large (>1µF) supply bypass capacitors. The discharged bypass capacitors are effectively put in parallel with COUT, causing a rapid drop in VOUT. No regulator can deliver enough current to prevent this problem if the load switch resistance is low and it is driven quickly. The only solution is to limit the rise time of the switch drive so that the load rise time is limited to approximately (25) • (CLOAD). Thus a 10µF capacitor would be require a 250µs rise time, limiting the charging current to about 200mA. Design Example As a design example, assume VIN will be operating from a maximum of 4.2V down to a minimum of 2.75V (powered by a single lithium-ion battery). Load current requirement is a maximum of 2A, but most of the time it will be in a standby mode requiring only 2mA. Efficiency at both low and high load currents is important. Burst Mode operation at light loads is desired. Output voltage is 1.8V. The IPRG pin will be left floating, so the maximum current sense threshold ∆VSENSE(MAX) is approximately 125mV. MaximumDuty Cycle = VOUT = 65.5% VIN(MIN) From Figure 1, SF = 82%. RDS(ON)MAX = ∆VSENSE(MAX) 5 • 0.9 • SF • = 0.032Ω 6 IOUT(MAX) • ρT A 0.032Ω P-channel MOSFET in Si7540DP is close to this value. 3808f 22 LTC3808 U W U U APPLICATIO S I FOR ATIO The N-channel MOSFET in Si7540DP has 0.017Ω RDS(ON). The short circuit current is: ISC = 90mV = 5.3A 0.017Ω So the inductor current rating should be higher than 5.3A. The PLLLPF pin will be left floating, so the LTC3808 will operate at its default frequency of 550kHz. For continuous Burst Mode operation with 600mA IRIPPLE, the required minimum inductor value is: LMIN = 1.8 V 1.8 V ⎞ ⎛ • ⎜ 1− ⎟ = 1.88µH 550kHz • 600mA ⎝ 2.75V ⎠ A 6A 2.2µH inductor works well for this application. CIN will require an RMS current rating of at least 1A at temperature. A COUT with 0.1 ESR will cause approximately 60mV output ripple. In most applications, the requirements for these capacitors are fairly similar. PC Board Layout Checklist When laying out the printed circuit board, use the following checklist to ensure proper operation of the LTC3808. • The power loop (input capacitor, MOSFET, inductor, output capacitor) should be as small as possible and isolated as much as possible from LTC3808. • Put the feedback resistors close to the VFB pins. The ITH compensation components should also be very close to the LTC3808. • The current sense traces (SENSE+ and SENSE–) should be Kelvin connections right at the P-channel MOSFET source and drain. • Keeping the switch node (SW) and the gate driver nodes (TG, BG) away from the small-signal components, especially the feedback resistors, and ITH compensation components. 3808f 23 LTC3808 U TYPICAL APPLICATIO S VIN 2.75V TO 8V 2 10nF 10k 1 8 1M 4 220pF CITH 15k RITH 6 3 187k 5 SYNC/MODE VIN SENSE+ PLLLPF IPRG TG PGOOD ITH SENSE– LTC3808EDE TRACK/SS VFB SW BG GND RUN 12 10Ω 1µF 10µF 11 10 MP Si7540DP 13 L 1.5µH VOUT 2.5V (5A AT 5VIN) 14 9 MN Si7540DP 7 COUT 150µF + 15 59k 100pF L: VISHAY IHLD-2525CZ-01 COUT: SANYO 4TPB150MC 3808 F11 Figure 11. 550kHz, Synchronous DC/DC Converter with Internal Soft-Start VIN 2.75V TO 8V 2 1 8 1M 4 100pF 22k 6 SYNC/MODE VIN SENSE+ PLLLPF IPRG TG PGOOD ITH SENSE– LTC3808EDE SW 12 10Ω 1µF 10µF 11 10 13 MP Si3447BDV L 1.5µH 14 VOUT 1.8V 2A 10nF 3 118k 5 59k TRACK/SS VFB BG GND 15 RUN 9 MN Si3460DV 7 D OPT COUT 22µF x2 100pF L: VISHAY IHLD-2525CZ-01 D: ON SEMI MBRM120L (OPTIONAL) 3808 F12 Figure 12. 750kHz, Synchronous DC/DC Converter with External Soft-Start, Ceramic Output Capacitor 3808f 24 LTC3808 U TYPICAL APPLICATIO S Synchronizable, Synchronous DC/DC Converter with Output Tracking VIN 2.75V TO 8V 2 10nF 10k 1 8 1M 4 220pF 15k 1.18k Vx 6 3 590Ω 5 118k SYNC/MODE VIN SENSE+ PLLLPF IPRG TG PGOOD ITH SENSE– LTC3808EDE TRACK/SS VFB SW BG GND RUN 12 10Ω 1µF 10µF 11 10 MP Si7540DP 13 L 1.5µH VOUT 1.8V (5A AT 5VIN) 14 9 MN Si7540DP COUT 150µF 7 + 15 59k 100pF L: VISHAY IHLP-2525CZ-01 COUT: SANYO 4TPB150MC VOUT < Vx 3808 TA02 Resistor Sensing, Synchronous DC/DC Converter with Spread Spectrum Modulation VIN 2.75V TO 8V 301k 2 SYNC/MODE VIN 1000pF 1 8 2200pF 1M 220pF 15k 4 6 SENSE+ 12 13 SENSE– 10 TG PGOOD ITH LTC3808EDE SW 10µF 11 PLLLPF IPRG 10Ω 1µF 0.03Ω RSENSE MP Si4431BDY 14 L 1.5µH VOUT 1.5V 2A 10nF 3 88.7k 5 59k TRACK/SS VFB BG GND RUN 9 7 MN Si4860DY COUT 150µF + 15 100pF L: VISHAY IHLP-2525CZ-01 COUT: SANYO 4TPB150MC RSENSE: DALE 0.25W 3808 TA03 3808f 25 LTC3808 U PACKAGE DESCRIPTIO DE Package 14-Lead Plastic DFN (4mm × 3mm) (Reference LTC DWG # 05-08-1708) 0.65 ±0.05 3.50 ±0.05 1.70 ±0.05 2.20 ±0.05 (2 SIDES) PACKAGE OUTLINE 0.25 ± 0.05 0.50 BSC 3.30 ±0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS R = 0.115 TYP 4.00 ±0.10 (2 SIDES) R = 0.20 TYP 3.00 ±0.10 (2 SIDES) 8 0.38 ± 0.10 14 1.70 ± 0.10 (2 SIDES) PIN 1 TOP MARK (SEE NOTE 6) PIN 1 NOTCH (DE14) DFN 1203 7 0.200 REF 1 0.25 ± 0.05 0.50 BSC 0.75 ±0.05 0.00 – 0.05 3.30 ±0.10 (2 SIDES) BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING PROPOSED TO BE MADE VARIATION OF VERSION (WGED-3) IN JEDEC PACKAGE OUTLINE MO-229 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 3808f 26 LTC3808 U PACKAGE DESCRIPTIO GN Package 16-Lead Plastic SSOP (Narrow .150 Inch) (Reference LTC DWG # 05-08-1641) .189 – .196* (4.801 – 4.978) .045 ± .005 16 15 14 13 12 11 10 9 .254 MIN .009 (0.229) REF .150 – .165 .229 – .244 (5.817 – 6.198) .0165 ± .0015 .150 – .157** (3.810 – 3.988) .0250 BSC RECOMMENDED SOLDER PAD LAYOUT 1 .015 ± .004 × 45° (0.38 ± 0.10) .007 – .0098 (0.178 – 0.249) 2 3 4 5 6 7 .0532 – .0688 (1.35 – 1.75) 8 .004 – .0098 (0.102 – 0.249) 0° – 8° TYP .016 – .050 (0.406 – 1.270) NOTE: 1. CONTROLLING DIMENSION: INCHES INCHES 2. DIMENSIONS ARE IN (MILLIMETERS) .008 – .012 (0.203 – 0.305) TYP .0250 (0.635) BSC GN16 (SSOP) 0204 3. DRAWING NOT TO SCALE *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 3808f Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 27 LTC3808 U TYPICAL APPLICATIO S 550kHz, Pulse-Skipping Mode, Synchronous DC/DC Converter with Ceramic Output Capacitor 1 PLLLPF VIN RVIN 10Ω 12 CIN 22µF CVIN 1µF VIN 3.3V LTC3808EDE 8 4 CITH 470pF RITH 22k 3 6 2 187k 5 SENSE+ IPRG PGOOD TG TRACK/SS ITH SYNC/MODE VFB GND 11 10 13 SENSE– 14 SW 9 BG 7 RUN 15 59k MP Si3447BDV MN Si3460DV VOUT 2.5V 2A L 1.5µH COUT 22µF 2x L: VISHAY IHLP-2525CZ-01 3808 TA04 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC1628/LTC3728 Dual High Efficiency, 2-Phase Synchronous Step Down Controllers Constant Frequency, Standby, 5V and 3.3V LDOs, VIN to 36V, 28-Lead SSOP LTC1735 High Efficiency Synchronous Step-Down Controller Burst Mode Operation, 16-Pin Narrow SSOP, Fault Protection, 3.5V ≤ VIN ≤ 36V LTC1772 Constant Frequency Current Mode Step-Down DC/DC Controller 2.5V ≤ VIN ≤ 9.8V, IOUT Up to 4A, SOT-23 Package, 550kHz LTC1773 Synchronous Step-Down Controller 2.65V ≤ VIN ≤ 8.5V, IOUT Up to 4A, 10-Lead MSOP LTC1778 No RSENSE, Synchronous Step-Down Controller Current Mode Operation Without Sense Resistor, Fast Transient Response, 4V ≤ VIN ≤ 36V LTC1872 Constant Frequency Current Mode Step-Up Controller 2.5V ≤ VIN ≤ 9.8V, SOT-23 Package, 550kHz LTC3411 1.25A (IOUT), 4MHz, Synchronous Step-Down DC/DC Converter 95% Efficiency, VIN: 2.5V to 5.5V, VOUT = 0.8V, IQ = 60mA, ISD = <1mA, MS Package LTC3412 2.5A (IOUT), 4MHz, Synchronous Step-Down DC/DC Converter 95% Efficiency, VIN: 2.5V to 5.5V, VOUT = 0.8V, IQ = 60mA, ISD = <1mA, TSSOP-16E Package LTC3416 4A, 4MHz, Monolithic Synchronous Step-Down Regulator Tracking Input to Provide Easy Supply Sequencing, 2.25V ≤ VIN ≤ 5.5V, 20-Lead TSSOP Package LTC3701 2-Phase, Low Input Voltage Dual Step-Down DC/DC Controller 2.5V ≤ VIN ≤ 9.8V, 550kHz, PGOOD, PLL, 16-Lead SSOP LTC3708 2-Phase, No RSENSE, Dual Synchronous Controller with Output Tracking Constant On-Time Dual Controller, VIN Up to 36V, Very Low Duty Cycle Operation, 5mm × 5mm QFN Package LTC3736 2-Phase, No RSENSE, Dual Synchronous Controller with Output Tracking 2.75V ≤ VIN ≤ 9.8V, 0.6V ≤ VOUT ≤ VIN, 4mm × 4mm QFN LTC3736-1 Low EMI 2-Phase, Dual Synchronous Controller with Output Tracking Integrated Spread Spectrum for 20dB Lower EMI, 2.75V ≤ VIN ≤ 9.8V LTC3737 2-Phase, No RSENSE, Dual DC/DC Controller with Output Tracking 2.75V ≤ VIN ≤ 9.8V, 0.6V ≤ VOUT ≤ VIN, 4mm × 4mm QFN PolyPhase is a trademark of Linear Technology Corporation. 3808f 28 Linear Technology Corporation LT/TP 0305 500 • PRINTED IN THE USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2005