19-2872; Rev 4; 6/12 KIT ATION EVALU E L B A AVAIL 300MHz-to-450MHz Low-Power, Crystal-Based ASK Transmitter The MAX1472 is a crystal-referenced phase-locked loop (PLL) VHF/UHF transmitter designed to transmit OOK/ASK data in the 300MHz to 450MHz frequency range. The MAX1472 supports data rates up to 100kbps, and adjustable output power to more than +10dBm into a 50Ω load. The crystal-based architecture of the MAX1472 eliminates many of the common problems with SAW transmitters by providing greater modulation depth, faster frequency settling, higher tolerance of the transmit frequency, and reduced temperature dependence. Combined, these improvements enable better overall receiver performance when using a superheterodyne receiver such as the MAX1470 or MAX1473. The MAX1472 is available in a 3mm x 3mm 8-pin SOT23 package and is specified for the automotive (-40°C to +125°C) temperature range. An evaluation kit is available. Contact Maxim Integrated Products for more information. Features o 2.1V to 3.6V Single-Supply Operation o Low 5.3mA Operating Supply Current* o Supports ASK with 90dB Modulation Depth o Output Power Adjustable to More than +10dBm o Uses Small Low-Cost Crystal o Small 3mm 3mm 8-Pin SOT23 Package o Fast-On Oscillator 220µs Startup Time *At 50% duty cycle (315MHz, 2.7V supply, +10dBm output power) Applications Ordering Information Remote Keyless Entry RF Remote Controls Tire Pressure Monitoring Security Systems PART TEMP RANGE MAX1472AKA+T -40°C to +125°C PINPACKAGE TOP MARK 8 SOT23 AEKS +Denotes a lead(Pb)-free/RoHS-compliant package. T = Tape and reel. Radio-Controlled Toys Wireless Game Consoles Wireless Computer Peripherals Wireless Sensors Pin Configuration Typical Application Circuit * TOP VIEW + 1 XTAL1 XTAL2 8 3.0V VDD 7 2 GND 50Ω ANTENNA MAX1472 220pF 680pF 3 PAGND 8 XTAL2 7 VDD 3 6 DATA PAOUT 4 5 ENABLE GND 2 MAX1472 DATA 6 DATA INPUT 4 PAOUT + XTAL1 1 ENABLE 5 PAGND STANDBY OR POWER-UP SOT23 *Optional power adjust resistor. For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 MAX1472 General Description MAX1472 300MHz-to-450MHz Low-Power, Crystal-Based ASK Transmitter ABSOLUTE MAXIMUM RATINGS VDD to GND ..........................................................-0.3V to +4.0V All Other Pins to GND ................................-0.3V to (VDD + 0.3V) Continuous Power Dissipation (TA = +70°C) 8-Pin SOT23 (derate 8.9mW/°C above +70°C)............714mW Operating Temperature Range .........................-40°C to +125°C Storage Temperature Range .............................-60°C to +150°C Lead Temperature (soldering, 10s) .................................+300°C Soldering Temperature (reflow) .......................................+260°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (Typical Application Circuit, output power is referenced to 50Ω, VDD = 2.1V to 3.6V, VENABLE = VDD, TA = -40°C to +125°C, unless otherwise noted. Typical values are at VDD = 2.7V, TA = +25°C, unless otherwise noted.) (Note 1) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 3.6 V SYSTEM PERFORMANCE Supply Voltage VDD 2.1 fRF = 315MHz Supply Current IDD fRF = 433MHz Standby Current Frequency Range ISTDBY 5.3 9.4 VENABLE = VDD, VDATA = VDD 9.1 16.6 VENABLE = VDD, VDATA = 0V 1.5 2.3 VENABLE = VDD (Note 2) 5.7 VENABLE = VDD, VDATA = VDD 9.6 VENABLE = VDD, VDATA = 0V 1.7 2.7 5 350 nA 1.7 µA mA VENABLE < VIL, TA < +85°C (Note 3) VENABLE < VIL TA < +125°C (Note 3) (Note 1) 300 450 MHz Data Rate (Note 3) 0 100 kbps Modulation Depth ON to OFF POUT ratio (Note 4) Output Power Turn-On Time Transmit Efficiency with CW Transmit Efficiency at 50% Duty Cycle 2 fRF VENABLE = VDD (Note 2) POUT tON 90 TA = +25°C, VDD = 2.7V (Notes 5, 6) 7.3 10.3 TA = +125°C, VDD = 2.1V (Notes 5, 6) 3.3 6.0 TA = -40°C, VDD = 3.6V (Notes 5, 6) 13.7 To fOFFSET < 50kHz (Note 7) 220 To fOFFSET < 5kHz (Note 7) 450 fRF = 315MHz (Note 8) 43.6 fRF = 433MHz (Note 8) 41.3 fRF = 315MHz (Note 9) 37.6 fRF = 433MHz (Note 9) 35.1 dB 12.8 dBm 16.2 µs % % 300MHz-to-450MHz Low-Power, Crystal-Based ASK Transmitter (Typical Application Circuit, output power is referenced to 50Ω, VDD = 2.1V to 3.6V, VENABLE = VDD, TA = -40°C to +125°C, unless otherwise noted. Typical values are at VDD = 2.7V, TA = +25°C, unless otherwise noted.) (Note 1) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS PHASE-LOCKED LOOP PERFORMANCE VCO Gain 330 fRF = 315MHz Phase Noise fRF = 433MHz Maximum Carrier Harmonics Reference Spur fOFFSET =100kHz -84 fOFFSET = 1MHz -91 fOFFSET =100kHz -82 fOFFSET = 1MHz -89 fRF = 315MHz -50 fRF = 433MHz -50 fRF = 315MHz -75 fRF = 433MHz -81 Loop Bandwidth Crystal Frequency fXTAL Oscillator Input Capacitance From each XTAL pin to GND Frequency Pushing by VDD MHz/V dBc/Hz dBc dBc 1.6 MHz fRF / 32 MHz 6.2 pF 3 ppm/V DIGITAL INPUTS Data Input High VIH Data Input Low VIL VDD - 0.25 V 0.25 V Maximum Input Current 2 nA Pulldown Current 25 µA Note 1: Note 2: Note 3: Note 4: Note 5: Note 6: Note 7: Note 8: Note 9: 100% tested at TA = +25°C. Guaranteed by design and characterization over temperature. 50% duty cycle at 10kHz data. Guaranteed by design and characterization, not production tested. Generally limited by PC board layout. Output power can be adjusted with external resistor. Guaranteed by design and characterization at fRF = 315MHz. VENABLE < VIL to VENABLE > VIH. fOFFSET is defined as the frequency deviation from the desired carrier frequency. VENABLE > VIH, VDATA > VIH, Efficiency = POUT/(VDD x IDD). VENABLE > VIH, DATA toggled from VIL to VIH, 10kHz, 50% duty cycle, Efficiency = POUT/(VDD x IDD). 3 MAX1472 ELECTRICAL CHARACTERISTICS (continued) Typical Operating Characteristics (Typical Application Circuit, VDD = 2.7V, TA = +25°C, unless otherwise noted.) -40°C +125°C 9 +85°C 8 1.6 1.5 1.4 7 1.3 6 1.2 5 +85°C -40°C +25°C 3.2 3.6 SUPPLY VOLTAGE (V) +125°C +85°C 1.8 1.6 13 OUTPUT POWER (dBm) 3.2 -40°C +25°C 1.4 1.2 2.4 2.8 3.2 12 VENABLE = VIH, VDATA = VIH, fRF = 315MHz -25°C 10 MAX1472 toc03 2.8 14 13 +125°C 9 +85°C 8 VENABLE = VIH, VDATA = VIH, fRF = 433MHz +25°C 11 -40°C 10 +125°C 9 7 8 6 7 +85°C 6 2.0 2.4 2.8 3.2 2.0 3.6 2.4 2.8 SUPPLY VOLTAGE (V) REFERENCE SPUR MAGNITUDE vs. SUPPLY VOLTAGE FREQUENCY STABILITY vs. SUPPLY VOLTAGE TRANSMIT POWER EFFICIENCY vs. SUPPLY VOLTAGE 2 MAX1472 toc07 315MHz -77 -79 433MHz 55 0 315MHz -1 433MHz -2 -40°C 50 EFFICIENCY (%) -73 1 OFFSET FREQUENCY (ppm) -71 -81 40 35 +125°C +85°C -3 30 -4 -85 2.4 2.8 SUPPLY VOLTAGE (V) 3.2 3.6 CW OUTPUT fRF = 315MHz 25 2.0 2.4 2.8 SUPPLY VOLTAGE (V) 3.2 3.6 3.6 +25°C 45 -83 4 3.2 SUPPLY VOLTAGE (V) -69 3.6 12 SUPPLY VOLTAGE (V) -67 2.0 3.2 OUTPUT POWER vs. SUPPLY VOLTAGE -40°C 11 3.6 -65 -75 2.4 SUPPLY VOLTAGE (V) 5 2.0 +125°C 2.0 3.6 MAX1472 toc08 SUPPLY CURRENT (mA) 2.0 2.8 OUTPUT POWER vs. SUPPLY VOLTAGE 14 MAX1472 toc04 VENABLE = VIH, VDATA = VIL, fRF = 433MHz 8 SUPPLY VOLTAGE (V) SUPPLY CURRENT vs. SUPPLY VOLTAGE 2.2 +85°C 9 5 2.4 2.0 OUTPUT POWER (dBm) 2.8 -40°C +25°C 10 6 MAX1472 toc05 2.4 11 7 1.1 2.0 VENABLE = VIH, VDATA = VIH, fRF = 433MHz 12 MAX1472 toc09 10 1.7 +125°C SUPPLY CURRENT (mA) 11 VENABLE = VIH, VDATA = VIL, fRF = 315MHz 1.8 13 MAX1472 toc02 +25°C SUPPLY CURRENT (mA) SUPPLY CURRENT (mA) MAX1472 toc01 VENABLE = VIH, VDATA = VIH, fRF = 315MHz 12 SUPPLY CURRENT vs. SUPPLY VOLTAGE SUPPLY CURRENT vs. SUPPLY VOLTAGE 1.9 MAX1472 toc06 SUPPLY CURRENT vs. SUPPLY VOLTAGE 13 REFERENCE SPUR (dBc) MAX1472 300MHz-to-450MHz Low-Power, Crystal-Based ASK Transmitter 2.0 2.4 2.8 SUPPLY VOLTAGE (V) 3.2 3.6 300MHz-to-450MHz Low-Power, Crystal-Based ASK Transmitter TRANSMIT POWER EFFICIENCY vs. SUPPLY VOLTAGE -40°C 40 35 +85°C 30 35 30 2.4 2.8 3.2 3.6 2.0 2.4 2.8 3.2 PHASE NOISE vs. OFFSET FREQUENCY SUPPLY CURRENT AND OUTPUT POWER vs. EXTERNAL RESISTOR MAX1472 toc13 -70 -80 -90 -100 -110 -120 fRF = 315MHz POWER 2.0 8 6 6 4 4 2 2 0 10 100 1k 10k 100k 1M 10M 0.1 fOFFSET (Hz) 1 10 100 3.2 3.6 fRF = 315MHz 9 0 1000 8 7 CW 6 5 4 50% DUTY CYCLE 3 2 0 2 4 6 8 10 OUTPUT POWER (dBm) EXTERNAL RESISTOR (Ω) FREQUENCY SETTLING TIME AM DEMODULATION OF PA OUTPUT MAX1472 toc16 MAX1472 toc17 DATA RATE = 100kHz ENABLE TRANSITION FROM LOW TO HIGH 25kHz/div START: 0s 2.8 SUPPLY CURRENT vs. OUTPUT POWER -130 -140 2.4 10 12 10 CURRENT 8 OOK OUTPUT AT 50% DUTY CYCLE fRF = 433MHz 20 SUPPLY CURRENT (mA) OUTPUT POWER (dBm) -60 MAX1472 toc14 12 10 25 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) -50 +85°C 3.6 SUPPLY VOLTAGE (V) -40 +125°C 30 OOK OUTPUT AT 50% DUTY CYCLE fRF = 315MHz 20 2.0 35 +125°C +85°C 25 CW OUTPUT fRF = 433MHz 25 PHASE NOISE (dBc/Hz) EFFICIENCY (%) +125°C 40 SUPPLY CURRENT (mA) EFFICIENCY (%) EFFICIENCY (%) 40 +25°C -40°C +25°C MAX1472 toc12 45 45 MAX1472 toc11 +25°C -40°C 45 50 MAX1472 toc10 50 TRANSMIT POWER EFFICIENCY vs. SUPPLY VOLTAGE MAX1472 toc15 TRANSMIT POWER EFFICIENCY vs. SUPPLY VOLTAGE 1ms 15%/div ENABLE TRANSITION FROM LOW TO HIGH 2.5kHz/div START: 0s 1ms START: 0s STOP: 20µs 5 MAX1472 Typical Operating Characteristics (continued) (Typical Application Circuit, VDD = 2.7V, TA = +25°C, unless otherwise noted.) 300MHz-to-450MHz Low-Power, Crystal-Based ASK Transmitter MAX1472 Pin Description PIN NAME FUNCTION 1 XTAL1 2 GND 3 PAGND Ground for the Power Amplifier (PA). Connect to system ground. 4 PAOUT Power-Amplifier Output. This output requires a pullup inductor to the supply voltage, which may be part of the output-matching network to a 50Ω antenna. 5 ENABLE Standby/Power-Up Input. A logic low on ENABLE places the device in standby mode. 6 DATA 7 VDD 8 XTAL2 1st Crystal Input. fRF = 32 x fXTAL. Ground. Connect to system ground. OOK Data Input. Power amplifier is ON when DATA is high. Supply Voltage. Bypass to GND with capacitor as close to the pin as possible. 2nd Crystal Input. fRF = 32 x fXTAL. Detailed Description The MAX1472 is a highly integrated OOK/ASK transmitter operating over the 300MHz to 450MHz frequency range. The IC includes a complete PLL and a highly efficient PA. The device can also be easily placed into a 5nA low-power shutdown mode. Shutdown Mode The ENABLE pin is internally pulled down with a 15µA current source. If the pin is left unconnected or pulled low, the MAX1472 goes into shutdown mode, where the supply current drops to less than 5nA. When ENABLE is high, the IC is enabled and is ready for transmission after 220µs (frequency settles to within 50kHz). The 220µs turn-on time of the MAX1472 is mostly dominated by the crystal oscillator startup time. Once the oscillator is running, the 1.6MHz PLL loop bandwidth allows fast-frequency recovery during power-amplifier toggling. Phase-Locked Loop The PLL block contains a phase detector, charge pump, integrated loop filter, VCO, 32X clock divider, and crystal oscillator. This PLL requires no external components, other than a crystal. The relationship between the carrier and crystal frequency is given by: fXTAL = fRF / 32 The lock-detect circuit prevents the PA from transmitting until the PLL is locked. In addition, the device shuts down the PA if the reference frequency is lost. 6 Power Amplifier (PA) The PA of the MAX1472 is a high-efficiency, open-drain, switch-mode amplifier. With proper output matching network, the PA can drive a wide range of impedances, including the small-loop PC board trace antenna and any 50Ω antenna. The output-matching network for a 50Ω antenna is shown in the Typical Application Circuit. The output-matching network suppresses the carrier harmonics and transforms the antenna impedance to an optimal impedance at PAOUT (pin 4), which is between 100Ω and 150Ω for a 2.7V supply. When the output matching network is properly tuned, the PA transmits power with high efficiency. The Typical Application Circuit delivers 10.3dBm at 2.7V supply with 9.1mA of supply current. Thus, the overall efficiency is 44%. The efficiency of the PA itself is more than 52%. Applications Information Output Power Adjustment It is possible to adjust the output power down to -10dBm with the addition of a resistor. The addition of the power-adjust resistor also reduces power consumption. See the Supply Current and Output Power vs. External Resistor and Supply Current vs. Output Power graphs in the Typical Operating Characteristics section. It is imperative to add both a low-frequency and a high-frequency decoupling capacitor as shown in the Typical Application Circuit. 300MHz-to-450MHz Low-Power, Crystal-Based ASK Transmitter Output Matching to 50Ω When matched to a 50Ω system, the MAX1472 PA is capable of delivering more than +10dBm of output power at VDD = 2.7V. The output of the PA is an opendrain transistor that requires external impedance matching and pullup inductance for proper biasing. The pullup inductance from PA to VDD serves three main purposes: It resonates the capacitance of the PA output, provides biasing for the PA, and becomes a high-frequency choke to reduce the RF energy coupling into VDD. The recommended output-matching network topology is shown in the Typical Application Circuit. The matching network transforms the 50Ω load to a higher impedance at the output of the PA in addition to forming a bandpass filter that provides attenuation for the higher order harmonics. fp = Cm 2 ⎛ ⎞ 1 1 6 − ⎜ ⎟ × 10 C + C C + C load case spec ⎠ ⎝ case where: fp is the amount the crystal frequency is pulled in ppm. Cm is the motional capacitance of the crystal. Ccase is the case capacitance. Cspec is the specified load capacitance. Cload is the actual load capacitance. When the crystal is loaded as specified, i.e., Cload = Cspec, the frequency pulling equals zero. Output Matching to PC Board Loop Antenna In most applications, the MAX1472 PA output has to be impedance matched to a small-loop antenna. The antenna is usually fabricated out of a copper trace on a PC board in a rectangular, circular, or square pattern. The antenna has an impedance that consists of a lossy component and a radiative component. To achieve high radiating efficiency, the radiative component should be as high as possible, while minimizing the lossy component. In addition, the loop antenna has an inherent loop inductance associated with it (assuming the antenna is terminated to ground). For example, in a typical application, the radiative impedance is less than 0.5Ω, the lossy impedance is less than 0.7Ω, and the inductance is approximately 50nH to 100nH. The objective of the matching network is to match the PA output to the small loop antenna. The matching components thus transform the low radiative and resistive parts of the antenna into the much higher value of the PA output, which gives higher efficiency. The low radiative and lossy components of the small loop antenna result in a higher Q matching network than the 50Ω network; thus, the harmonics are lower. 7 MAX1472 Crystal Oscillator The crystal oscillator in the MAX1472 is designed to present a capacitance of approximately 3.1pF between the XTAL1 and XTAL2 pins. If a crystal designed to oscillate with a different load capacitance is used, the crystal is pulled away from its intended operating frequency, thus introducing an error in the reference frequency. Crystals designed to operate with higher differential load capacitance always pull the reference frequency higher. For example, a 9.84375MHz crystal designed to operate with a 10pF load capacitance oscillates at 9.84688MHz with the MAX1472, causing the transmitter to be transmitting at 315.1MHz rather than 315.0MHz, an error of about 100kHz, or 320ppm. In actuality, the oscillator pulls every crystal. The crystal’s natural frequency is really below its specified frequency, but when loaded with the specified load capacitance, the crystal is pulled and oscillates at its specified frequency. This pulling is already accounted for in the specification of the load capacitance. Additional pulling can be calculated if the electrical parameters of the crystal are known. The frequency pulling is given by: MAX1472 300MHz-to-450MHz Low-Power, Crystal-Based ASK Transmitter Layout Considerations A properly designed PC board is an essential part of any RF/microwave circuit. On the PA output, use controlled-impedance lines and keep them as short as possible to minimize losses and radiation. At high frequencies, trace lengths that are on the order of λ/10 or longer can act as antennas. Keeping the traces short also reduces parasitic inductance. Generally, 1in of PC board trace adds about 20nH of parasitic inductance. The parasitic inductance can have a dramatic effect on the effective inductance. For example, a 0.5in trace connecting a 100nH inductor adds an extra 10nH of inductance, or 10%. To reduce the parasitic inductance, use wider traces and a solid ground or power plane below the signal traces. Using a solid ground plane can reduce the parasitic inductance from approximately 20nH/in to 7nH/in. Also, use low-inductance connections to ground on all GND pins, and place decoupling capacitors close to all VDD connections. Functional Diagram DATA ENABLE VDD MAX1472 8 PA PAOUT PAGND LOCK DETECT 32 x PLL GND CRYSTALOSCILLATOR DRIVER XTAL1 XTAL2 Package Information Chip Information PROCESS: CMOS AND GATE For the latest package outline information and land patterns (footprints), go to www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 8 SOT23 K8SN+1 21-0078 90-0176 300MHz-to-450MHz Low-Power, Crystal-Based ASK Transmitter REVISION NUMBER REVISION DATE 1 4/05 — 2 6/09 Updated EC table Max supply currents, added lead-free note, and corrected Electrical Characteristics notes 3 10/10 4 6/12 DESCRIPTION PAGES CHANGED — Removed Maximum Crystal Inductance spec from Electrical Characteristics table Updated Electrical Characteristics, updated Power Amplifier (PA) section 1, 2, 3, 6, 8 3 3, 6 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. 9 __________________Maxim Integrated Products, Inc. 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 © 2012 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc. MAX1472 Revision History