19-3274; Rev 0; 5/04 +3.3V, 1Mbps, Low-Supply-Current CAN Transceiver The MAX3051 interfaces between the CAN protocol controller and the physical wires of the bus lines in a controller area network (CAN). The MAX3051 provides differential transmit capability to the bus and differential receive capability to the CAN controller. The MAX3051 is primarily intended for +3.3V single-supply applications that do not require the stringent fault protection specified by the automotive industry (ISO 11898). The MAX3051 features four different modes of operation: high-speed, slope-control, standby, and shutdown mode. High-speed mode allows data rates up to 1Mbps. The slope-control mode can be used to program the slew rate of the transmitter for data rates of up to 500kbps. This reduces the effects of EMI, thus allowing the use of unshielded twisted or parallel cable. In standby mode, the transmitter is shut off and the receiver is pulled high, placing the MAX3051 in lowcurrent mode. In shutdown mode, the transmitter and receiver are switched off. The MAX3051 input common-mode range is from -7V to +12V, exceeding the ISO 11898 specification of -2V to +7V. These features, and the programmable slew-rate limiting, make the part ideal for nonautomotive, harsh environments. The MAX3051 is available in 8-pin SO and SOT23 packages and operates over the -40°C to +85°C extended temperature range. Features ♦ Low +3.3V Single-Supply Operation ♦ Wide -7V to +12V Common-Mode Range ♦ Small SOT23 Package ♦ Four Operating Modes High-Speed Operation Up to 1Mbps Slope-Control Mode to Reduce EMI (Up to 500kbps) Standby Mode Low-Current Shutdown Mode ♦ Thermal Shutdown ♦ Current Limiting Ordering Information TEMP RANGE PINPACKAGE MAX3051ESA -40°C to +85°C 8 SO MAX3051EKA-T -40°C to +85°C 8 SOT23-8 PART TOP MARK — AEKF Pin Configuration Applications Printers JetLink Industrial Control and Networks TOP VIEW Telecom Backplane Consumer Applications TXD 1 8 RS 7 CANH 3 6 CANL RXD 4 5 SHDN GND 2 MAX3051 VCC SO/SOT23 Typical Operating Circuit at end of data sheet. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 MAX3051 General Description MAX3051 +3.3V, 1Mbps, Low-Supply-Current CAN Transceiver ABSOLUTE MAXIMUM RATINGS VCC to GND ..............................................................-0.3V to +6V TXD, RS, SHDN to GND ...........................................-0.3V to +6V RXD to GND .............................................................-0.3V to +6V CANH, CANL to GND..........................................-7.5V to +12.5V Continuous Power Dissipation (TA = +70°C) 8-Pin SO (derate 5.9mW/°C above +70°C)...................470mW 8-Pin SOT23 (derate 9.7mW/°C above +70°C).............774mW Operating Temperature Range ...........................-40°C to +85°C Maximum Junction Temperature .....................................+150°C Storage Temperature Range .............................-65°C to +150°C Lead Temperature Range (soldering, 10s)......................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VCC = +3.3V ±5%, RL = 60Ω, CL = 100pF, TA = TMIN to TMAX, unless otherwise noted. Typical values are at VCC = +3.3V and TA = +25°C.) (Note 1) PARAMETER Supply Current SYMBOL IS Shutdown Current ISHDN Thermal-Shutdown Threshold VTSH Dominant CONDITIONS MIN TYP 35 MAX 70 Recessive 2 5 Standby 8 15 µA 1 µA VSHDN = VCC, TXD = VCC or floating Thermal-Shutdown Hysteresis UNITS mA +160 °C 25 °C TXD INPUT LEVELS High-Level Input Voltage VIH Low-Level Input Voltage VIL Input Capacitance Pullup Resistor 2 CIN VCC + 0.3V V 0.8 V 100 kΩ 3 V 5 RINTXD 50 pF CANH, CANL TRANSMITTER Recessive Bus Voltage VCANH, VCANL VTXD = VCC, no load 2 2.3 VTXD = VCC, no load, VRS = VCC (standby mode) -100 +100 mV Off-State Output Leakage -2V < VCANH, VCANL < +7V, SHDN = HIGH -250 +250 µA Input Leakage Current VCC = 0V, VCANH = VCANL = 5V -250 +250 µA 2.45 CANH Output Voltage VCANH VTXD = 0V CANL Output Voltage VCANL VTXD = 0V Differential Output 2 (VCANH VCANL) V 1.25 VTXD = 0V 1.5 3.0 VTXD = 0V, RL = 45Ω 1.2 3.0 VTXD = VCC, no load -500 +50 VTXD = VCC, RL = 60Ω -120 +12 _______________________________________________________________________________________ V V mV +3.3V, 1Mbps, Low-Supply-Current CAN Transceiver (VCC = +3.3V ±5%, RL = 60Ω, CL = 100pF, TA = TMIN to TMAX, unless otherwise noted. Typical values are at VCC = +3.3V and TA = +25°C.) (Note 1) PARAMETER SYMBOL CANH Short-Circuit Current ICANHSC CANL Short-Circuit Current ICANLSC CONDITIONS -7V ≤ VCANH ≤ 0V MIN TYP MAX -200 UNITS mA Minimum foldback current -35 VCC ≤ VCANL ≤ 12V 200 mA VCC V 0.4 V RXD OUTPUT LEVELS RXD High Output-Voltage Level VOH I = -1mA RXD Low Output-Voltage Level VOL I = 4mA 0.8 x VCC DC BUS RECEIVER (VTXD = VCC; CANH and CANL externally driven; -7V ≤ VCANH, VCANL ≤ +12V, unless otherwise specified) -7V ≤ VCM ≤ +12V 0.5 Differential Input Voltage VDIFF V (Recessive) VRS = VCC (standby mode) 0.5 Differential Input Voltage (Dominant) Differential Input Hysteresis CANH and CANL Input Resistance Differential Input Resistance VDIFF Dominant 0.9 VRS = VCC (standby mode) 1.1 VDIFF(HYST) 20 V mV RI 20 50 kΩ RDIFF 40 100 kΩ 0.3 x VCC V MODE SELECTION (RS) Input Voltage for High Speed VSLP Input Voltage for Standby VSTBY Slope-Control Mode Voltage High-Speed Mode Current VSLOPE IHS 0.75 x VCC RRS = 25kΩ to 200kΩ 0.4 x VCC VRS = 0 V 0.6 x VCC V -500 µA 0.8 V 100 kΩ SHUTDOWN (SHDN) SHDN Input Voltage High VSHDNH SHDN Input Voltage Low VSHDNL SHDN Pulldown Resistor RINSHDN 2 50 V _______________________________________________________________________________________ 3 MAX3051 ELECTRICAL CHARACTERISTICS (continued) MAX3051 +3.3V, 1Mbps, Low-Supply-Current CAN Transceiver TIMING CHARACTERISTICS (VCC = +3.3V ±5%, RL = 60Ω, CL = 100pF, TA = TMIN to TMAX, unless otherwise noted. Typical values are at VCC = +3.3V and TA = +25°C.) PARAMETER Delay TXD to Bus Active (Figure 1) Delay TXD to Bus Inactive (Figure 1) Delay Bus to Receiver Active (Figure 1) Delay Bus to Receiver Inactive (Figure 1) Differential-Output Slew Rate SYMBOL CONDITIONS MIN TYP VRS = 0V (≤1Mbps) tONTXD RRS = 25kΩ (≤500kbps) 183 RRS = 100kΩ (≤125kbps) 770 RRS = 25kΩ (≤500kbps) 226 RRS = 100kΩ (≤125kbps) 834 SR ns 80 RRS = 25kΩ (≤500kbps) 200 RRS = 100kΩ (≤125kbps) 730 VRS = 0V (≤1Mbps) tOFFRXD ns 70 VRS = 0V (≤1Mbps) tONRXD UNITS 50 VRS = 0V (≤1Mbps) tOFFTXD MAX ns 100 RRS = 25kΩ (≤500kbps) 245 RRS = 100kΩ (≤125kbps) 800 VRS = 0V (≤1Mbps) 96 RRS = 25kΩ (≤500kbps) 12.5 RRS = 100kΩ (≤125kbps) 2.9 RRS = 200kΩ (≤62.5kbps) 1.6 ns V/µs Bus Dominant to RXD Active tDRXDL VRS > 0.8 x VCC, standby, Figure 2 1 Standby to Receiver Active tSBRXDL BUS dominant, Figure 2 4 µs 1 µs 4 µs SHDN to Bus Inactive tOFFSHDN TXD = GND, Figure 3 (Note 2) SHDN to Receiver Active tONSHDN BUS dominant, Figure 3 (Note 3) SHDN to Standby tSHDNSB Figure 4 20 Note 1: All currents into device are positive; all currents out of the device are negative. All voltages are referenced to device ground, unless otherwise noted. Note 2: No other devices on the BUS. Note 3: BUS externally driven. 4 _______________________________________________________________________________________ µs µs +3.3V, 1Mbps, Low-Supply-Current CAN Transceiver TXD RS VCC /2 VCC /2 VCC x 0.75 BUS EXTERNALLY DRIVEN tONTXD tOFFTXD 0.9V VDIFF 1.1V VDIFF tSBRXDL 0.5V tONRXD RXD RXD VCC /2 VCC /2 VCC /2 Figure 1. Timing Diagram SHDN tDRXDL tOFFRXD VCC /2 Figure 2. Timing Diagram for Standby Signal VCC /2 VCC /2 SHDN VCC /2 tONSHDN tOFFSHDN VDIFF tSHDNSB 0.5V 0.75V × VCC BUS EXTERNALLY DRIVEN RS RXD VCC /2 Figure 3. Timing Diagram for Shutdown Signal Figure 4. Timing Diagram for Shutdown-to-Standby Signal _______________________________________________________________________________________ 5 MAX3051 Timing Diagrams Typical Operating Characteristics (VCC = +3.3V, RL = 60Ω, CL = 100pF, TA = +25°C, unless otherwise specified.) SLEW RATE vs. RRS AT 100kbps 20 15 10 19 TA = +25°C 16 TA = +85°C 13 5 0 100 80 60 40 20 0 10 20 40 60 80 100 120 140 160 180 200 0 200 RRS (kΩ) 400 600 800 -15 10 10.0 9.5 9.0 8.5 50 RECEIVER PROPAGATION DELAY (ns) 10.5 60 RECEIVER PROPAGATION DELAY vs. TEMPERATURE MAX3051toc04 11.0 35 TEMPERATURE (°C) DATA RATE (kbps) STANDBY SUPPLY CURRENT vs. TEMPERATURE (RS = VCC) STANDBY SUPPLY CURRENT (µA) -40 1000 MAX3051toc05 0 MAX3051toc03 SHUTDOWN SUPPLY CURRENT (nA) 25 TA = -40°C 22 120 MAX3051toc02 25 SUPPLY CURRENT (mA) 30 SHUTDOWN SUPPLY CURRENT vs. TEMPERATURE (SHDN = VCC) SUPPLY CURRENT vs. DATA RATE MAX3051toc01 35 SLEW RATE (V/µs) 45 RECESSIVE 40 35 30 DOMINANT 25 20 15 10 5 RRS = GND 0 8.0 -15 10 35 60 -40 85 -15 10 35 TEMPERATURE (°C) DRIVER PROPAGATION DELAY vs. TEMPERATURE RECEIVER OUTPUT LOW vs. OUTPUT CURRENT 1.6 MAX3051toc06 50 40 1.4 VOLTAGE RXD (V) 1.2 30 RECESSIVE 20 TA = -85°C 1.0 TA = +25°C 0.8 TA = -40°C 0.6 0.4 DOMINANT 10 85 60 TEMPERATURE (°C) MAX3051toc07 -40 DRIVER PROPAGATION DELAY (ns) MAX3051 +3.3V, 1Mbps, Low-Supply-Current CAN Transceiver 0.2 RRS = GND, DATA RATE = 100kbps 0 0 -40 -15 10 35 TEMPERATURE (°C) 6 60 85 0 5 10 15 20 25 30 35 OUTPUT CURRENT (mA) _______________________________________________________________________________________ 40 45 85 +3.3V, 1Mbps, Low-Supply-Current CAN Transceiver MAX3051 Typical Operating Characteristics (continued) (VCC = +3.3V, RL = 60Ω, CL = 100pF, TA = +25°C, unless otherwise specified.) RECEIVER OUTPUT HIGH vs. OUTPUT CURRENT DIFFERENTIAL VOLTAGE vs. DIFFERENTIAL LOAD TA = -40°C 3.0 DIFFERENTIAL VOLTAGE (V) 1.4 1.2 1.0 0.8 0.6 0.4 MAX3051toc09 3.5 MAX3051toc08 1.6 2.5 TA = -85°C 2.0 TA = +25°C 1.5 1.0 0.5 0.2 0 0 1 2 3 4 5 6 7 8 0 100 200 OUTPUT CURRENT (mA) DIFFERENTIAL LOAD RL (Ω) RECEIVER PROPAGATION DELAY DRIVER PROPAGATION DELAY RS = GND 300 MAX3051toc11 MAX3051toc10 CAHN - CANL TXD 2V/div RRS = 24kΩ RXD 1v/div RRS = 75kΩ RRS = 100kΩ 200ns/div 200ns/div LOOPBACK PROPAGATION DELAY vs. RRS DRIVER PROPAGATION DELAY TXD 1V/div CAHN - CANL MAX3051toc13 1200 LOOPBACK PROPAGATION DELAY (ns) 0 MAX3051toc12 RECEIVER OUTPUT HIGH (VCC - RXD) (V) 1.8 1000 800 600 400 200 RS = GND 0 200ns/div 0 20 40 60 80 100 120 140 160 180 200 RRS (kΩ) _______________________________________________________________________________________ 7 +3.3V, 1Mbps, Low-Supply-Current CAN Transceiver MAX3051 Detailed Description PIN NAME FUNCTION 1 TXD Transmit Data Input. TXD is a CMOS/TTL-compatible input from a CAN controller. TXD has an internal 75kΩ pullup resistor. 2 GND Ground 3 VCC Supply Voltage. Bypass VCC to GND with a 0.1µF capacitor. 4 RXD Receive Data Output. RXD is a CMOS/TTL-compatible output. 5 SHDN Shutdown Input, CMOS/TTL-Compatible. Drive SHDN high to put the MAX3051 in shutdown. SHDN has an internal 75kΩ pulldown resistor to GND. 6 CANL CAN Bus Line Low 7 CANH 8 CAN Bus Line High Mode-Select Input. Drive RS low or connect to GND for high-speed operation. Connect a resistor between RS and GND to control output slope. Drive RS high to put into standby mode (see the Mode Selection section). RS VCC MAX3051 THERMAL SHUTDOWN VCC TRANSMITTER CONTROL TXD RS CANH CANL MODE SELECTION GND RXD RECEIVER SHUTDOWN SHDN 0.75V Figure 5. MAX3051 Functional Diagram 8 _______________________________________________________________________________________ +3.3V, 1Mbps, Low-Supply-Current CAN Transceiver The receiver reads differential inputs from the bus lines (CANH, CANL) and transfers this data as a singleended output (RXD) to the CAN controller. It consists of a comparator that senses the difference VDIFF = (CANH - CANL) with respect to an internal threshold of +0.75V. If this VDIFF is greater than 0.75, a logic-low is present at RXD. If VDIFF is less than 0.75V, a logic-high is present. The receiver always echoes the CAN BUS data. The MAX3051 interfaces between the CAN protocol controller and the physical wires of the bus lines in a CAN. It provides differential transmit capability to the bus and differential receive capability to the CAN controller. It is primarily intended for +3.3V single-supply applications that do not require the stringent fault protection specified by the automotive industry (ISO 11898) The MAX3051 features four different modes of operation: high-speed, slope-control, standby, and shutdown mode. High-speed mode allows data rates up to 1Mbps. The slope-control mode can be used to program the slew rate of the transmitter for data rates of up to 500kbps. This reduces the effects of EMI, thus allowing the use of unshielded twisted or parallel cable. In standby mode, the transmitter is shut off and the receiver is pulled high, placing the MAX3051 in lowcurrent mode. In shutdown mode, the transmitter and receiver are switched off. The CANH and CANL common-mode range is -7V to +12V. RXD is logic-high when CANH and CANL are shorted or terminated and undriven. Mode Selection High-Speed Mode Connect RS to ground to set the MAX3051 to highspeed mode. When operating in high-speed mode, the MAX3051 can achieve transmission rates of up to 1Mbps. In high-speed mode, use shielded twisted pair cable to avoid EMI problems. The MAX3051 input common-mode range is from -7V to +12V, exceeding the ISO 11898 specification of -2V to +7V. These features, and the programmable slew-rate limiting, make the part ideal for nonautomotive, harsh environments. Slope-Control Mode Connect a resistor from RS to ground to select slopecontrol mode (Table 2). In slope-control mode, CANH and CANL slew rates are controlled by the resistor connected to the RS pin. Maximum transmission speeds are controlled by R RS and range from 40kbps to 500kbps. Controlling the rise and fall slopes reduces EMI and allows the use of an unshielded twisted pair or a parallel pair of wires as bus lines. The equation for selecting the resistor value is given by: The transceivers operate from a single +3.3V supply and draw 35µA of supply current in dominant state and 2µA in recessive state. In standby mode, supply current is reduced to 8µA. In shutdown mode, supply current is less than 1µA. CANH and CANL are output short-circuit current limited and are protected against excessive power dissipation by thermal-shutdown circuitry that places the driver outputs into a high-impedance state. RRS (kΩ) ≈ 12000 / (maximum speed in kbps) Transmitter See the Slew Rate vs. RRS graph in the Typical Operating Characteristics. The transmitter converts a single-ended input (TXD) from the CAN controller to differential outputs for the bus lines (CANH, CANL). The truth table for the transmitter and receiver is given in Table 1. Standby Mode If a logic-high is applied to RS, the MAX3051 enters a low-current standby mode. In this mode, the transmitter Table 1. Transmitter and Receiver Truth Table When Not Connected to The Bus TXD RS SHDN CANH CANL BUS STATE RXD Low VRS < 0.75 x VCC Low High Low Dominant Low High or float VRS < 0.75 x VCC Low 5kΩ to 25kΩ to VCC / 2 5kΩ to 25kΩ to VCC / 2 Recessive High X VRS > 0.75 x VCC Low 5kΩ to 25kΩ to GND 5kΩ to 25kΩ to GND Recessive High X X High Floating Floating Floating High _______________________________________________________________________________________ 9 MAX3051 Receiver Detailed Description MAX3051 +3.3V, 1Mbps, Low-Supply-Current CAN Transceiver is switched off and the receiver is switched to a lowcurrent/low-speed state. If dominant bits are detected, RXD switches to low level. The microcontroller should react to this condition by switching the transceiver back to normal operation. When the MAX3051 enters standby mode, RXD goes high for 4µs (max) regardless of the BUS state. However, after 4µs, RXD goes low only when the BUS is dominant, otherwise RXD remains high (when the BUS is recessive). For proper measurement of standbyto-receiver active time (tSBRXDL), the BUS should be in dominant state (see Figure 2). Shutdown Drive SHDN high to enter shutdown mode. Connect SHDN to ground or leave floating for normal operation. Thermal Shutdown If the junction temperature exceeds +160°C, the device is switched off. The hysteresis is approximately 25°C, disabling thermal shutdown once the temperature drops below 135°C. In thermal shutdown, CANH and CANL go recessive and all IC functions are disabled. Applications Information Reduced EMI and Reflections In slope-control mode, the CANH and CANL outputs are slew-rate limited, minimizing EMI and reducing reflections caused by improperly terminated cables. In multidrop CAN applications, it is important to maintain a direct point-to-point wiring scheme. A single pair of wires should connect each element of the CAN bus, and the two ends of the bus should be terminated with 120Ω resistors (Figure 6). A star configuration should never be used. Any deviation from the point-to-point wiring scheme creates a stub. The high-speed edge of the CAN data on a stub can create reflections back down the bus. These reflections can cause data errors by eroding the noise margin of the system. Although stubs are unavoidable in a multidrop system, care should be taken to keep these stubs as small as possible, especially in high-speed mode. In slope-control mode, the requirements are not as rigorous, but stub length should still be minimized. Power Supply and Bypassing The MAX3051 requires no special layout considerations beyond common practices. Bypass VCC to GND with a 0.1µF ceramic capacitor mounted close to the IC with short lead lengths and wide trace widths. Table 2. Mode Selection Truth Table CONDITION FORCED AT PIN RS 10 MODE RESULTING CURRENT AT RS VRS < 0.3 x VCC High Speed |IRS| < 500µA 0.4 x VCC <VRS < 0.6 x VCC Slope Control 10µA < |IRS| < 200µA VRS > 0.75 x VCC Standby |IRS| < 10µA ______________________________________________________________________________________ +3.3V, 1Mbps, Low-Supply-Current CAN Transceiver TWISTED PAIR CANH TXD RXD MAX3051 MAX3051 RL = 120Ω RL = 120Ω TRANSCEIVER 3 CANL STUB LENGTH KEEP AS SHORT AS POSSIBLE TRANSCEIVER 2 TRANSCEIVER 1 Figure 6. Multiple Receivers Connected to CAN Bus Typical Operating Circuit 120Ω VCC 0.1µF VCC CANH CAN CONTROLLER MAX3051 TX0 TXD RX0 RXD RS GND CANL GND 25kΩ TO 200kΩ 120Ω Chip Information TRANSISTOR COUNT: 1024 PROCESS: BiCMOS ______________________________________________________________________________________ 11 Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) DIM A A1 B C e E H L N E H INCHES MILLIMETERS MAX MIN 0.069 0.053 0.010 0.004 0.014 0.019 0.007 0.010 0.050 BSC 0.150 0.157 0.228 0.244 0.016 0.050 MAX MIN 1.35 1.75 0.10 0.25 0.35 0.49 0.25 0.19 1.27 BSC 3.80 4.00 5.80 6.20 0.40 SOICN .EPS MAX3051 +3.3V, 1Mbps, Low-Supply-Current CAN Transceiver 1.27 VARIATIONS: 1 INCHES TOP VIEW DIM D D D MIN 0.189 0.337 0.386 MAX 0.197 0.344 0.394 MILLIMETERS MIN 4.80 8.55 9.80 MAX 5.00 8.75 10.00 N MS012 8 AA 14 AB 16 AC D A B e C 0∞-8∞ A1 L FRONT VIEW SIDE VIEW PROPRIETARY INFORMATION TITLE: PACKAGE OUTLINE, .150" SOIC APPROVAL DOCUMENT CONTROL NO. 21-0041 12 ______________________________________________________________________________________ REV. B 1 1 +3.3V, 1Mbps, Low-Supply-Current CAN Transceiver CL CL E MIN MAX A A1 A2 0.90 0.00 0.90 1.45 0.15 1.30 b 0.28 0.45 C D E 0.09 2.80 2.60 0.20 3.00 3.00 SYMBOL e CL E1 E1 1.50 L 0.30 L2 e PIN 1 I.D. DOT (SEE NOTE 6) SOT23, 8L .EPS SEE DETAIL "A" b 1.75 0.60 0.25 BSC. 0.65 BSC. 1.95 REF. 0∞ 8∞ e1 0 e1 D C CL L2 A A2 GAUGE PLANE A1 SEATING PLANE C 0 L NOTE: 1. ALL DIMENSIONS ARE IN MILLIMETERS. 2. FOOT LENGTH MEASURED FROM LEAD TIP TO UPPER RADIUS OF HEEL OF THE LEAD PARALLEL TO SEATING PLANE C. 3. PACKAGE OUTLINE EXCLUSIVE OF MOLD FLASH & METAL BURR. 4. PACKAGE OUTLINE INCLUSIVE OF SOLDER PLATING. DETAIL "A" 5. COPLANARITY 4 MILS. MAX. 6. PIN 1 I.D. DOT IS 0.3 MM ÿ MIN. LOCATED ABOVE PIN 1. 7. SOLDER THICKNESS MEASURED AT FLAT SECTION OF LEAD BETWEEN 0.08mm AND 0.15mm FROM LEAD TIP. 8. MEETS JEDEC MO178. PROPRIETARY INFORMATION TITLE: PACKAGE OUTLINE, SOT-23, 8L BODY APPROVAL DOCUMENT CONTROL NO. 21-0078 REV. D 1 1 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13 © 2004 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products. MAX3051 Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.)