MAXIM MAX495CSA

19-0265; Rev 2; 9/96
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
The dual MAX492, quad MAX494, and single MAX495
operational amplifiers combine excellent DC accuracy
with rail-to-rail operation at the input and output. Since
the common-mode voltage extends from VCC to VEE,
the devices can operate from either a single supply
(+2.7V to +6V) or split supplies (±1.35V to ±3V). Each
op amp requires less than 150µA supply current. Even
with this low current, the op amps are capable of driving
a 1kΩ load, and the input referred voltage noise is only
25nV/√Hz. In addition, these op amps can drive loads in
excess of 1nF.
The precision performance of the MAX492/MAX494/
MAX495, combined with their wide input and output
dynamic range, low-voltage single-supply operation, and
very low supply current, makes them an ideal choice for
battery-operated equipment and other low-voltage applications. The MAX492/MAX494/MAX495 are available in
DIP and SO packages in the industry-standard op-amp
pin configurations. The MAX495 is also available in the
smallest 8-pin SO: the µMAX package.
________________________Applications
Portable Equipment
Battery-Powered Instruments
Data Acquisition
Signal Conditioning
Low-Voltage Applications
____________________________Features
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
Low-Voltage Single-Supply Operation (+2.7V to +6V)
Rail-to-Rail Input Common-Mode Voltage Range
Rail-to-Rail Output Swing
500kHz Gain-Bandwidth Product
Unity-Gain Stable
150µA Max Quiescent Current per Op Amp
No Phase Reversal for Overdriven Inputs
200µV Offset Voltage
High Voltage Gain (108dB)
High CMRR (90dB) and PSRR (110dB)
Drives 1kΩ Load
Drives Large Capacitive Loads
MAX495 Available in µMAX Package—8-Pin SO
______________Ordering Information
PART
TEMP. RANGE
PIN-PACKAGE
MAX492CPA
0°C to +70°C
8 Plastic DIP
MAX492CSA
MAX492C/D
MAX492EPA
MAX492ESA
MAX492MJA
0°C to +70°C
0°C to +70°C
-40°C to +85°C
-40°C to +85°C
-55°C to +125°C
8 SO
Dice*
8 Plastic DIP
8 SO
8 CERDIP
Ordering Information continued at end of data sheet.
*Dice are specified at TA = +25°C, DC parameters only.
__________Typical Operating Circuit
_________________Pin Configurations
TOP VIEW
+5V
1
VDD
10k
2
MAX187
(ADC)
7
6
3
ANALOG
INPUT
MAX495
2
DOUT 6
8
SCLK
7
CS
AIN
4
3
SHDN
4
REF
10k
OUT1 1
8
VCC
IN1- 2
7
OUT2
IN1+ 3
6
IN2-
5
IN2+
8
N.C.
7
VCC
IN1+ 3
6
OUT
VEE 4
5
NULL
VEE 4
MAX492
DIP/SO
SERIAL
INTERFACE
NULL 1
4.096V
GND
5
IN1- 2
MAX495
DIP/SO/µMAX
INPUT SIGNAL CONDITIONING FOR LOW-VOLTAGE ADC
Pin Configurations continued at end of data sheet.
________________________________________________________________ Maxim Integrated Products
1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800
MAX492/MAX494/MAX495
_______________General Description
MAX492/MAX494/MAX495
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
ABSOLUTE MAXIMUM RATINGS
Supply Voltage (VCC to VEE) ....................................................7V
Common-Mode Input Voltage..........(VCC + 0.3V) to (VEE - 0.3V)
Differential Input Voltage .........................................±(VCC - VEE)
Input Current (IN+, IN-, NULL1, NULL2) ..........................±10mA
Output Short-Circuit Duration ....................Indefinite short circuit
to either supply
Voltage Applied to NULL Pins ....................................VCC to VEE
Continuous Power Dissipation (TA = +70°C)
8-Pin Plastic DIP (derate 9.09mW/°C above +70°C) ....727mW
8-Pin SO (derate 5.88mW/°C above +70°C).................471mW
8-Pin CERDIP (derate 8.00mW/°C above +70°C).........640mW
8-Pin µMAX (derate 4.1mW/°C above +70°C) ..............330mW
14-Pin Plastic DIP (derate 10.00mW/°C above +70°C)...800mW
14-Pin SO (derate 8.33mW/°C above +70°C)...............667mW
14-Pin CERDIP (derate 9.09mW/°C above +70°C).......727mW
Operating Temperature Ranges
MAX49_C_ _ ........................................................0°C to +70°C
MAX49_E_ _......................................................-40°C to +85°C
MAX49_M_ _ ...................................................-55°C to +125°C
Junction Temperatures
MAX49_C_ _/E_ _..........................................................+150°C
MAX49_M_ _ .................................................................+175°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VCC = 2.7V to 6V, VEE = GND, VCM = 0V, VOUT = VCC / 2, TA = +25°C, unless otherwise noted.)
PARAMETER
CONDITIONS
TYP
MAX
UNITS
±200
±500
µV
VCM = VEE to VCC
±25
±60
nA
VCM = VEE to VCC
±0.5
±6
Input Offset Voltage
VCM = VEE to VCC
Input Bias Current
Input Offset Current
Differential Input Resistance
Common-Mode Input
Voltage Range
Common-Mode Rejection Ratio
Power-Supply Rejection Ratio
Large-Signal Voltage Gain
(Note 1)
Output Voltage Swing
(Note 1)
MIN
2
VEE - 0.25
V
74
90
dB
VCC = 2.7V to 6V
VCC = 2.7V,
RL = 100kΩ,
VOUT = 0.25V to 2.45V
dB
88
110
Sourcing
90
104
Sinking
90
102
VCC = 2.7V, RL = 1kΩ,
VOUT = 0.5V to 2.2V
Sourcing
94
105
Sinking
78
90
VCC = 5.0V,
RL = 100kΩ,
VOUT = 0.25V to 4.75V
Sourcing
98
108
Sinking
92
100
VCC = 5.0V, RL = 1kΩ,
VOUT = 0.5V to 4.5V
Sourcing
98
110
86
98
RL = 100kΩ
Sinking
VOH
VOL
VOH
dB
VCC - 0.075 VCC - 0.04
VEE + 0.04 VEE + 0.075
VCC - 0.20
VOL
VCC - 0.15
30
Operating Supply Voltage Range
2.7
VCM = VOUT = VCC / 2
V
VEE + 0.15 VEE + 0.20
Output Short-Circuit Current
2
VCC + 0.25
(VEE - 0.25V) ≤ VCM ≤ (VCC + 0.25V)
RL = 1kΩ
Supply Current (per amplifier)
nA
MΩ
mA
6.0
VCC = 2.7V
135
150
VCC = 5V
150
170
_______________________________________________________________________________________
V
µA
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
(VCC = 2.7V to 6V, VEE = GND, TA = +25°C, unless otherwise noted.)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Gain-Bandwidth Product
RL = 100kΩ, CL = 100pF
500
kHz
Phase Margin
RL = 100kΩ, CL = 100pF
60
degrees
Gain Margin
RL = 100kΩ, CL = 100pF
10
dB
Total Harmonic Distortion
RL = 10kΩ, CL = 15pF, VOUT = 2Vp-p, AV = +1, f = 1kHz
0.003
%
Slew Rate
RL = 100kΩ, CL = 15pF
0.20
V/µs
Time
To 0.1%, 2V step
12
µs
Turn-On Time
VCC = 0V to 3V step, VIN = VCC / 2, AV = +1
5
µs
Input Noise-Voltage Density
f = 1kHz
25
nV/√Hz
Input Noise-Current Density
f = 1kHz
0.1
pA/√Hz
Amp-Amp Isolation
f = 1kHz
125
dB
DC ELECTRICAL CHARACTERISTICS
(VCC = 2.7V to 6V, VEE = GND, VCM = 0V, VOUT = VCC / 2, TA = 0°C to +70°C, unless otherwise noted.)
PARAMETER
Input Offset Voltage
CONDITIONS
MIN
TYP
VCM = VEE to VCC
MAX
±650
Input Offset Voltage Tempco
±2
UNITS
µV
µV/°C
Input Bias Current
VCM = VEE to VCC
±75
nA
Input Offset Current
Common-Mode Input
Voltage Range
Common-Mode Rejection Ratio
VCM = VEE to VCC
±6
nA
(VEE - 0.20) ≤ VCM ≤ (VCC + 0.20)
72
dB
Power-Supply Rejection Ratio
VCC = 2.7V to 6V
86
dB
Large-Signal Voltage Gain
(Note 1)
Output Voltage Swing
(Note 1)
VEE - 0.20
VCC = 2.7V, RL = 100kΩ,
VOUT = 0.25V to 2.45V
Sourcing
88
Sinking
84
VCC = 2.7V, RL = 1kΩ,
VOUT = 0.5V to 2.2V
Sourcing
92
Sinking
76
VCC = 5.0V, RL = 100kΩ,
VOUT = 0.25V to 4.75V
Sourcing
92
Sinking
88
VCC = 5.0V, RL = 1kΩ,
VOUT = 0.5V to 4.5V
Sourcing
96
RL = 100kΩ
RL = 1kΩ
Sinking
VOH
Supply Current (per amplifier)
VEE + 0.075
VCC - 0.20
V
VEE + 0.20
2.7
VCM = VOUT = VCC / 2
dB
82
VOL
Operating Supply Voltage Range
V
VCC - 0.075
VOL
VOH
VCC + 0.20
6.0
VCC = 2.7V
175
VCC = 5V
190
V
µA
_______________________________________________________________________________________
3
MAX492/MAX494/MAX495
AC ELECTRICAL CHARACTERISTICS
MAX492/MAX494/MAX495
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
DC ELECTRICAL CHARACTERISTICS
(VCC = 2.7V to 6V, VEE = GND, VCM = 0V, VOUT = VCC / 2, TA = -40°C to +85°C, unless otherwise noted.)
PARAMETER
Input Offset Voltage
CONDITIONS
MIN
MAX
VCM = VEE to VCC
±950
Input Offset Voltage Tempco
±2
UNITS
µV
µV/°C
Input Bias Current
VCM = VEE to VCC
±100
nA
Input Offset Current
Common-Mode Input
Voltage Range
Common-Mode Rejection Ratio
VCM = VEE to VCC
±8
nA
(VEE - 0.15) ≤ VCM ≤ (VCC + 0.15)
68
dB
Power-Supply Rejection Ratio
VCC = 2.7V to 6V, VCM = 0V
84
dB
Large-Signal Voltage Gain
(Note 1)
Output Voltage Swing
(Note 1)
VEE - 0.15
VCC = 2.7V, RL = 100kΩ,
VOUT = 0.25V to 2.45V
Sourcing
86
Sinking
84
VCC = 2.7V, RL = 1kΩ,
VOUT = 0.5V to 2.2V
Sourcing
92
Sinking
76
VCC = 5.0V, RL = 100kΩ,
VOUT = 0.25V to 4.75V
Sourcing
92
Sinking
86
VCC = 5.0V, RL = 1kΩ,
VOUT = 0.5V to 4.5V
Sourcing
96
Sinking
80
RL = 100kΩ
RL = 1kΩ
VOH
VOH
Supply Current (per amplifier)
VCC + 0.15
dB
VEE + 0.075
VCC - 0.20
VOL
V
VEE + 0.20
2.7
VCM = VOUT = VCC / 2
V
VCC - 0.075
VOL
Operating Supply-Voltage Range
4
TYP
6.0
VCC = 2.7V
185
VCC = 5V
200
_______________________________________________________________________________________
V
µA
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
MAX492/MAX494/MAX495
DC ELECTRICAL CHARACTERISTICS
(VCC = 2.7V to 6V, VEE = GND, VCM = 0V, VOUT = VCC / 2, TA = -55°C to +125°C, unless otherwise noted.)
PARAMETER
Input Offset Voltage
CONDITIONS
MIN
TYP
VCM = VEE to VCC
Input Offset Voltage Tempco
MAX
UNITS
±1.2
mV
±2
µV/°C
Input Bias Current
VCM = VEE to VCC
±200
nA
Input Offset Current
VCM = VEE to VCC
±10
nA
Common-Mode Input Voltage Range
VEE - 0.05
VCC + 0.05
V
Common-Mode Rejection Ratio
(VEE - 0.05V) ≤ VCM ≤ (VCC + 0.05V)
66
dB
Power-Supply Rejection Ratio
VCC = 2.7V to 6V
80
dB
Large-Signal Voltage Gain
(Note 1)
Output Voltage Swing
(Note 1)
VCC = 2.7V, RL = 100kΩ,
VOUT = 0.25V to 2.45V
Sourcing
82
Sinking
80
VCC = 2.7V, RL = 1kΩ,
VOUT = 0.5V to 2.2V
Sourcing
90
Sinking
72
VCC = 5.0V, RL = 100kΩ,
VOUT = 0.25V to 4.75V
Sourcing
86
Sinking
82
VCC = 5.0V, RL = 1kΩ,
VOUT = 0.5V to 4.5V
Sourcing
94
RL = 100kΩ
RL = 1kΩ
Sinking
VOH
VEE + 0.075
VCC - 0.250
VOL
Operating Supply-Voltage Range
Supply Current (per amplifier)
76
VCC - 0.075
VOL
VOH
V
VEE + 0.250
2.7
VCM = VOUT = VCC / 2
dB
6.0
VCC = 2.7V
200
VCC = 5V
225
V
µA
Note 1: RL to VEE for sourcing and VOH tests; RL to VCC for sinking and VOL tests.
_______________________________________________________________________________________
5
__________________________________________Typical Operating Characteristics
(TA = +25°C, VCC = 5V, VEE = 0V, unless otherwise noted.)
GAIN AND PHASE
vs. FREQUENCY
MAX492-01
80
180
60
80
120
140
60
120
GAIN
-60
0
PHASE
PSRR (dB)
0
20
PHASE (DEG)
GAIN (dB)
0
PHASE
100
60
40
PHASE (DEG)
60
40
GAIN (dB)
180
120
GAIN
20
POWER-SUPPLY REJECTION RATIO
vs. FREQUENCY
MAX492-02
MAX492-03
GAIN AND PHASE
vs. FREQUENCY
-60
0
VCC
80
60
40
VEE
20
FREQUENCY (kHz)
10
1
100
MAX492-04
160
OFFSET VOLTAGE (µV)
120
100
80
60
40
VCM = 0V
140
20
120
110
80
60
100
1000 10,000
80
70
INPUT BIAS CURRENT (nA)
100
VCC = 6V
5
0
-5
-10
-15
-20
25
-50
4
VCM (V)
5
6
7
VCM = 0
-75
-125
3
VCC = 2.7V
-25
-30
2
VCM = VCC
0
-100
1
SUPPLY CURRENT PER AMPLIFIER
vs. TEMPERATURE
50
-25
0
VCC = 6V
75
VCC = 6V
-60 -40 -20 0
20 40 60 80 100 120 140
TEMPERATURE (°C)
125
MAX492-07
VCC = 2.7V
VCM = -0.4V TO +5.4V
-60 -40 -20 0
INPUT BIAS CURRENT
vs. TEMPERATURE
20
10
20 40 60 80 100 120 140
TEMPERATURE (°C)
INPUT BIAS CURRENT
vs. COMMON-MODE VOLTAGE
VCM = -0.2V TO +5.2V
VCM = -0.3V TO +5.3V
60
-60 -40 -20 0
FREQUENCY (kHz)
15
90
40
0
10
1
VCM = 0V TO +5V
VCM = -01V TO +5.1V
100
100
20 40 60 80 100 120 140
TEMPERATURE (°C)
220
SUPPLY CURRENT PER OP AMP (µA)
0.1
1000
120
MAX492-08
0
0.01
100
10
COMMON-MODE REJECTION RATIO
vs. TEMPERATURE
20
VIN = 2.5V
1
FREQUENCY (kHz)
OFFSET VOLTAGE
vs. TEMPERATURE
140
CHANNEL SEPARATION (dB)
0.1
VIN = 2.5V
-20
0.1
0.01
FREQUENCY (kHz)
CHANNEL SEPARATION
vs. FREQUENCY
6
0
-180
1000 10,000
MAX492-06
100
-40
0.01
-120
CMRR (dB)
10
-180
1000 10,000
CL = 470pF
AV = +1000
RL = ∞
MAX492-05
AV = +1000
NO LOAD
-40
0.01 0.1
1
-20
200
MAX492-09
-120
-20
INPUT BIAS CURRENT (nA)
MAX492/MAX494/MAX495
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
VOUT = VCM = VCC/2
180
160
VCC = 5V
140
VCC = 2.7V
120
100
80
60
40
20
0
-60 -40 -20 0
20 40 60 80 100 120 140
TEMPERATURE (°C)
_______________________________________________________________________________________
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
LARGE-SIGNAL GAIN
vs. OUTPUT VOLTAGE
110
100
RL = 100kΩ
RL = 1kΩ
80
70
90
RL = 100kΩ
RL = 10kΩ
RL = 1kΩ
80
70
VCC = +6V
RL TO VEE
60
VCC = +2.7V
RL TO VEE
60
50
500
600
100
LARGE-SIGNAL GAIN
vs. OUTPUT VOLTAGE
GAIN (dB)
80
VCC = +6V
RL TO VCC
500
600
140
VCC = 2.7V, RL = 1kΩ
100
80
VCC = 6V, RL = 100kΩ
40
20
VCC = 2.7V, RL = 100kΩ
0
0 20 40 60 80 100 120 140
TEMPERATURE (°C)
95
RL TO VEE
90
80
100
200
300 400
VOUT (mV)
500
-60 -40 -20 0
600
180
RL TO VEE
160
VCC = 6V, RL = 1kΩ
140
OUTPUT IMPEDANCE
vs. FREQUENCY
VCC = 2.7V, RL = 1kΩ
120
100
80
60
40
20 40 60 80 100 120 140
TEMPERATURE (°C)
VCC = 6V, RL = 100kΩ
VCC = 2.7V, RL = 100kΩ
1000
VCM = VOUT = 2.5V
100
10
1
20
0
-60 -40 -20
105
85
200
(VCC - VOUT) (mV)
VOUT MIN (mV)
160
VCC = +6V
100
MAXIMUM OUTPUT VOLTAGE
vs. TEMPERATURE
VCC = 6V, RL = 1kΩ
120
RL TO VCC
110
VCC = +2.7V
VCC = +2.7V
RL TO VCC
0
MAX492-16
RL TO VCC
RL = 100kΩ, 0.3V < VOUT < (VCC - 0.3V)
115
OUTPUT IMPEDANCE (Ω)
300 400
VOUT (mV)
220
60
RL = 1kΩ
RL = 10kΩ
60
MINIMUM OUTPUT VOLTAGE
vs. TEMPERATURE
180
120
50
200
20 40 60 80 100 120 140
LARGE-SIGNAL GAIN
vs. TEMPERATURE
90
70
50
200
-60 -40 -20 0
MAX492-17
GAIN (dB)
70
100
RL TO VEE
TEMPERATURE (°C)
RL = 100kΩ
RL = 1kΩ
RL = 10kΩ
0
VCC = +6V
90
600
100
90
60
500
RL = 1MΩ
110
RL = 100kΩ
80
400
200 300
VCC - VOUT (mV)
120
MAX492-13
RL = 1MΩ
100
VCC = +2.7V
95
LARGE-SIGNAL GAIN
vs. OUTPUT VOLTAGE
120
110
100
80
0
LARGE-SIGNAL GAIN (dB)
400
200 300
VCC - VOUT (mV)
MAX492-14
100
105
85
50
0
RL TO VCC
110
MAX492-15
90
GAIN (dB)
RL = 1MΩ
RL = 1kΩ, 0.5V < VOUT < (VCC - 0.5V)
115
MAX492-18
100
RL = 1MΩ
LARGE-SIGNAL GAIN (dB)
110
120
MAX492-11
RL = 10kΩ
GAIN (dB)
120
MAX492-10
120
LARGE-SIGNAL GAIN
vs. TEMPERATURE
MAX492-12
LARGE-SIGNAL GAIN
vs. OUTPUT VOLTAGE
0.1
-60 -40 -20 0 20 40 60 80 100 120 140
TEMPERATURE (°C)
0.01
0.1
1
10
100
1,000 10,000
FREQUENCY (kHz)
_______________________________________________________________________________________
7
MAX492/MAX494/MAX495
____________________________Typical Operating Characteristics (continued)
(TA = +25°C, VCC = 5V, VEE = 0V, unless otherwise noted.)
____________________________Typical Operating Characteristics (continued)
(TA = +25°C, VCC = 5V, VEE = 0V, unless otherwise noted.)
CURRENT-NOISE DENSITY
vs. FREQUENCY
VOLTAGE-NOISE DENSITY
vs. FREQUENCY
CURRENT-NOISE DENSITY (pA/√Hz)
10
INPUT REFERRED
MAX492-20
5.0
MAX492-19
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
INPUT REFERRED
0
1
0.01
1
0.1
0.01
10
10
TOTAL HARMONIC DISTORTION + NOISE
vs. PEAK-TO-PEAK SIGNAL AMPLITUDE
TOTAL HARMONIC DISTORTION + NOISE
vs. FREQUENCY
0.1
MAX492-21
0.1
THD + NOISE (%)
AV = +1
2VP-P SIGNAL
80kHz LOWPASS FILTER
0.01
1
0.1
FREQUENCY (kHz)
FREQUENCY (kHz)
RL = 10kΩ TO GND
AV = +1
1kHz SINE
22kHz FILTER
RL TO GND
MAX492-22
VOLTAGE-NOISE DENSITY (nV/√Hz)
100
THD + NOISE (%)
MAX492/MAX494/MAX495
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
RL = 1kΩ
RL = 2kΩ
0.01
RL = 100kΩ
RL = 10kΩ
NO LOAD
0.001
0.001
10
1000
100
4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0
10,000
PEAK-TO-PEAK SIGNAL AMPLITUDE (V)
FREQUENCY (Hz)
SMALL-SIGNAL TRANSIENT RESPONSE
SMALL-SIGNAL TRANSIENT RESPONSE
2µs/div
VCC = +5V, AV = +1, RL = 10kΩ
8
VIN
50mV/div
VIN
50mV/div
VOUT
50mV/div
VOUT
50mV/div
2µs/div
VCC = +5V, AV = -1, RL = 10kΩ
_______________________________________________________________________________________
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
LARGE-SIGNAL TRANSIENT RESPONSE
LARGE-SIGNAL TRANSIENT RESPONSE
VIN
2V/div
VIN
2V/div
VOUT
2V/div
VOUT
2V/div
50µs/div
50µs/div
VCC = +5V, AV = +1, RL = 10kΩ
VCC = +5V, AV = -1, RL = 10kΩ
______________________________________________________________Pin Description
PIN
MAX492 MAX494 MAX495
NAME
FUNCTION
1
1
—
OUT1
Amplifier 1 Output
—
—
1, 5
NULL
Offset Null Input. Connect to a 10kΩ potentiometer for offset-voltage trimming.
Connect wiper to VEE (Figure 3).
—
—
2
IN-
Inverting Input
2
2
—
IN1-
Amplifier 1 Inverting Input
—
—
3
IN+
Noninverting Input
3
3
—
IN1+
Amplifier 1 Noninverting Input
4
11
4
VEE
Negative Power-Supply Pin. Connect to ground or a negative voltage.
5
5
—
IN2+
Amplifier 2 Noninverting Input
—
—
6
OUT
Amplifier Output
6
6
—
IN2-
Amplifier 2 Inverting Input
7
7
—
OUT2
8
4
7
VCC
—
8
—
OUT3
—
9
—
IN3-
Amplifier 3 Inverting Input
—
10
—
IN3+
Amplifier 3 Noninverting Input
—
12
—
IN4+
Amplifier 4 Noninverting Input
—
13
—
IN4-
Amplifier 4 Inverting Input
—
14
—
OUT4
—
—
8
N.C.
Amplifier 2 Output
Positive Power-Supply Pin. Connect to (+) terminal of power supply.
Amplifier 3 Output
Amplifier 4 Output
No Connect. Not internally connected.
_______________________________________________________________________________________
9
MAX492/MAX494/MAX495
____________________________Typical Operating Characteristics (continued)
(TA = +25°C, VCC = 5V, VEE = 0V, unless otherwise noted.)
MAX492/MAX494/MAX495
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
__________Applications Information
The dual MAX492, quad MAX494, and single MAX495
op amps combine excellent DC accuracy with rail-torail operation at both input and output. With their precision performance, wide dynamic range at low supply
voltages, and very low supply current, these op amps
are ideal for battery-operated equipment and other lowvoltage applications.
Rail-to-Rail Inputs and Outputs
The MAX492/MAX494/MAX495’s input common-mode
range extends 0.25V beyond the positive and negative
supply rails, with excellent common-mode rejection.
Beyond the specified common-mode range, the outputs are guaranteed not to undergo phase reversal or
latchup. Therefore, the MAX492/MAX494/MAX495 can
be used in applications with common-mode signals at
or even beyond the supplies, without the problems
associated with typical op amps.
The MAX492/MAX494/MAX495’s output voltage swings
to within 50mV of the supplies with a 100kΩ load. This
rail-to-rail swing at the input and output substantially
increases the dynamic range, especially in low supplyvoltage applications. Figure 1 shows the input and output waveforms for the MAX492, configured as a
unity-gain noninverting buffer operating from a single
+3V supply. The input signal is 3.0Vp-p, 1kHz sinusoid
centered at +1.5V. The output amplitude is approximately 2.95Vp-p.
Input Offset Voltage
Rail-to-rail common-mode swing at the input is obtained
by two complementary input stages in parallel, which
feed a folded cascaded stage. The PNP stage is active
for input voltages close to the negative rail, and the
NPN stage is active for input voltages close to the positive rail.
The offsets of the two pairs are trimmed; however, there
is some small residual mismatch between them. This
mismatch results in a two-level input offset characteristic, with a transition region between the levels occurring
at a common-mode voltage of approximately 1.3V.
Unlike other rail-to-rail op amps, the transition region
has been widened to approximately 600mV in order to
minimize the slight degradation in CMRR caused by
this mismatch.
To adjust the MAX495’s input offset voltage (500µV max
at +25°C), connect a 10kΩ trim potentiometer between
the two NULL pins (pins 1 and 5), with the wiper connected to VEE (pin 4) (Figure 2). The trim range of this
circuit is ±6mV. External offset adjustment is not available for the dual MAX492 or quad MAX494.
The input bias currents of the MAX492/MAX494/MAX495
are typically less than 50nA. The bias current flows into
the device when the NPN input stage is active, and it
flows out when the PNP input stage is active. To reduce
the offset error caused by input bias current flowing
through external source resistances, match the effective resistance seen at each input. Connect resistor R3
between the noninverting input and ground when using
10k
VIN
1
NULL
MAX495
VOUT
4
Figure 1. Rail-to-Rail Input and Output (Voltage Follower
Circuit, VCC = +3V, VEE = 0V)
10
VEE
NULL
5
Figure 2. Offset Null Circuit
______________________________________________________________________________________
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
(Figure 4). The diodes limit the differential voltage
applied to the amplifiers’ internal circuitry to no more
than VF, where VF is the diodes’ forward-voltage drop
(about 0.7V at +25°C).
Input bias current for the ICs (±25nA typical) is specified for the small differential input voltages. For large
differential input voltages (exceeding VF), this protection circuitry increases the input current at IN+ and IN-:
Input Stage Protection Circuitry
The MAX492/MAX494/MAX495 include internal protection circuitry that prevents damage to the precision
input stage from large differential input voltages. This
protection circuitry consists of back-to-back diodes
between IN+ and IN- with two 1.7kΩ resistors in series
(VIN+ - VIN- ) - VF
Input Current = ———————————
2 x 1.7kΩ
For comparator applications requiring large differential
voltages (greater than VF), you can limit the input current that flows through the diodes with external resistors
R2
MAX492
MAX494
MAX495
TO INTERNAL
CIRCUITRY
1.7kΩ
IN+
R1
VIN
VOUT
MAX49_
R3
R3 = R2 II R1
IN–
TO INTERNAL
CIRCUITRY
1.7kΩ
Figure 3a. Reducing Offset Error Due to Bias Current:
Inverting Configuration
Figure 4. Input Stage Protection Circuitry
MAX492-FG 04
10,000
R3
VIN
VOUT
MAX49_
R2
R3 = R2 II R1
R1
CAPACITIVE LOAD (pF)
UNSTABLE REGION
1000
VCC = +5V
VOUT = VCC/2
RL TO VEE
AV = +1
100
1
10
100
RESISTIVE LOAD (kΩ)
Figure 3b. Reducing Offset Error Due to Bias Current:
Figure 5. Capacitive-Load Stable Region Sourcing Current
Noninverting Configuration
______________________________________________________________________________________ 11
MAX492/MAX494/MAX495
the op amp in an inverting configuration (Figure 3a);
connect resistor R3 between the noninverting input and
the input signal when using the op amp in a noninverting configuration (Figure 3b). Select R3 to equal the
parallel combination of R1 and R2. High source resistances will degrade noise performance, due to the thermal noise of the resistor and the input current noise
(which is multiplied by the source resistance).
MAX492/MAX494/MAX495
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
in series with IN-, IN+, or both. Series resistors are not
recommended for amplifier applications, as they may
increase input offsets and decrease amplifier bandwidth.
Output Loading and Stability
Even with their low quiescent current of less than 150µA
per op amp, the MAX492/MAX494/MAX495 are well
suited for driving loads up to 1kΩ while maintaining DC
accuracy. Stability while driving heavy capacitive loads
is another key advantage over comparable CMOS railto-rail op amps.
VIN
50mV/div
VIN
50mV/div
VOUT
50mV/div
VOUT
50mV/div
10µs/div
10µs/div
Figure 6. MAX492 Voltage Follower with 1000pF Load
(RL = ∞)
Figure 7b. MAX492 Voltage Follower with 500pF Load—
RL = 20kΩ
VIN
50mV/div
VIN
50mV/div
VOUT
50mV/div
VOUT
50mV/div
10µs/div
Figure 7a. MAX492 Voltage Follower with 500pF Load—
RL = 5kΩ
12
In op amp circuits, driving large capacitive loads
increases the likelihood of oscillation. This is especially
true for circuits with high loop gains, such as a unitygain voltage follower. The output impedance and a
capacitive load form an RC network that adds a pole to
the loop response and induces phase lag. If the pole
frequency is low enough—as when driving a large
capacitive load—the circuit phase margin is degraded,
leading to either an under-damped pulse response or
oscillation.
10µs/div
Figure 7c. MAX492 Voltage Follower with 500pF Load—
RL = ∞
______________________________________________________________________________________
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
To increase stability while driving large capacitive
loads, connect a pull-up resistor at the output to
decrease the current that the amplifier must source. If
the amplifier is made to sink current rather than source,
stability is further increased.
Frequency stability can be improved by adding an output isolation resistor (RS) to the voltage-follower circuit
(Figure 8). This resistor improves the phase margin of
the circuit by isolating the load capacitor from the op
amp’s output. Figure 9a shows the MAX492 driving
10,000pF (RL ≥ 100kΩ), while Figure 9b adds a 47Ω
isolation resistor.
VIN
50mV/div
RS
VOUT
MAX49_
CL
VIN
VOUT
50mV/div
10µs/div
Figure 9b. Driving a 10,000pF Capacitive Load with a 47Ω
Isolation Resistor
Figure 8. Capacitive-Load Driving Circuit
+5V
VCC
VIN
50mV/div
2
7
1k
6
MAX495
3
VOUT
50mV/div
VOUT
4
1k
10µs/div
Figure 9a. Driving a 10,000pF Capacitive Load
Figure 10. Power-Up Test Configuration
______________________________________________________________________________________
13
MAX492/MAX494/MAX495
The MAX492/MAX494/MAX495 can drive capacitive
loads in excess of 1000pF under certain conditions
(Figure 5). When driving capacitive loads, the greatest
potential for instability occurs when the op amp is
sourcing approximately 100µA. Even in this case, stability is maintained with up to 400pF of output capacitance. If the output sources either more or less current,
stability is increased. These devices perform well with a
1000pF pure capacitive load (Figure 6). Figure 7 shows
the performance with a 500pF load in parallel with various load resistors.
MAX492/MAX494/MAX495
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
VCC
2V/div
VCC
1V/div
VOUT
500mV/div
5µs/div
Figure 11a. Power-Up Settling Time (VCC = +3V)
Because the MAX492/MAX494/MAX495 have excellent
stability, no isolation resistor is required, except in the
most demanding applications. This is beneficial
because an isolation resistor would degrade the lowfrequency performance of the circuit.
Power-Up Settling Time
The MAX492/MAX494/MAX495 have a typical supply
current of 150µA per op amp. Although supply current is
already low, it is sometimes desirable to reduce it further
by powering down the op amp and associated ICs for
periods of time. For example, when using a MAX494 to
buffer the inputs to a multi-channel analog-to-digital converter (ADC), much of the circuitry could be powered
down between data samples to increase battery life. If
samples are taken infrequently, the op amps, along with
the ADC, may be powered down most of the time.
When power is reapplied to the MAX492/MAX494/
MAX495, it takes some time for the voltages on the supply pin and the output pin of the op amp to settle.
Supply settling time depends on the supply voltage, the
value of the bypass capacitor, the output impedance of
the incoming supply, and any lead resistance or inductance between components. Op amp settling time
depends primarily on the output voltage and is slew-rate
limited. With the noninverting input to a voltage follower
held at mid-supply (Figure 10), when the supply steps
from 0V to VCC, the output settles in approximately 4µs
for V CC = +3V (Figure 11a) or 10µs for V CC = +5V
(Figure 11b).
14
VOUT
1V/div
5µs/div
Figure 11b. Power-Up Settling Time (VCC = +5V)
Power Supplies and Layout
The MAX492/MAX494/MAX495 operate from a single
2.7V to 6V power supply, or from dual supplies of
±1.35V to ±3V. For single-supply operation, bypass the
power supply with a 1µF capacitor in parallel with a
0.1µF ceramic capacitor. If operating from dual supplies, bypass each supply to ground.
Good layout improves performance by decreasing the
amount of stray capacitance at the op amp’s inputs and
output. To decrease stray capacitance, minimize both
trace lengths and resistor leads and place external
components close to the op amp’s pins.
Rail-to-Rail Buffers
The Typical Operating Circuit shows a MAX495 gain-oftwo buffer driving the analog input to a MAX187 12-bit
ADC. Both devices run from a single 5V supply, and the
converter’s internal reference is 4.096V. The MAX495’s
typical input offset voltage is 200µV. This results in an
error at the ADC input of 400µV, or less than half of one
least significant bit (LSB). Without offset trimming, the
op amp contributes negligible error to the conversion
result.
______________________________________________________________________________________
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
PART
TEMP. RANGE
_________________Chip Topographies
MAX492
PIN-PACKAGE
MAX494CPD
0°C to +70°C
14 Plastic DIP
MAX494CSD
MAX494EPD
MAX494ESD
MAX494MJD
MAX495CPA
0°C to +70°C
-40°C to +85°C
-40°C to +85°C
-55°C to +125°C
0°C to +70°C
14 SO
14 Plastic DIP
14 SO
14 CERDIP
8 Plastic DIP
MAX495CSA
MAX495CUA
MAX495C/D
MAX495EPA
MAX495ESA
MAX495MJA
0°C to +70°C
0°C to +70°C
0°C to +70°C
-40°C to +85°C
-40°C to +85°C
-55°C to +125°C
8 SO
8 µMAX
Dice*
8 Plastic DIP
8 SO
8 CERDIP
IN1+
IN1-
V CC
OUT1
0.068"
(1.728mm)
V EE
V CC
V CC
OUT2
* Dice are specified at TA = +25°C, DC parameters only.
IN2+
IN2-
0.069"
(1.752mm)
____Pin Configurations (continued)
MAX495
NULL1
TOP VIEW
INOUT1 1
14 OUT4
IN1- 2
13 IN4-
IN1+ 3
12 IN4+
VCC 4
MAX494
11 VEE
IN2+ 5
10 IN3+
IN2- 6
9
IN3-
OUT2 7
8
OUT3
V CC
0.056"
(1.422mm)
OUT
IN+
V EE
DIP/SO
NULL2
0.055"
(1.397mm)
TRANSISTOR COUNT: 134 (single MAX495)
268 (dual MAX492)
536 (quad MAX494)
SUBSTRATE CONNECTED TO VEE
______________________________________________________________________________________
15
MAX492/MAX494/MAX495
_Ordering Information (continued)
MAX492/MAX494/MAX495
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
________________________________________________________Package Information
DIM
C
α
A
0.101mm
0.004 in
e
B
A1
L
A
A1
B
C
D
E
e
H
L
α
INCHES
MAX
MIN
0.044
0.036
0.008
0.004
0.014
0.010
0.007
0.005
0.120
0.116
0.120
0.116
0.0256
0.198
0.188
0.026
0.016
6°
0°
MILLIMETERS
MIN
MAX
0.91
1.11
0.10
0.20
0.25
0.36
0.13
0.18
2.95
3.05
2.95
3.05
0.65
4.78
5.03
0.41
0.66
0°
6°
21-0036D
E
H
8-PIN µMAX
MICROMAX SMALL-OUTLINE
PACKAGE
D
DIM
D
0°-8°
A
0.101mm
0.004in.
e
B
A1
E
C
L
Narrow SO
SMALL-OUTLINE
PACKAGE
(0.150 in.)
H
A
A1
B
C
E
e
H
L
INCHES
MAX
MIN
0.069
0.053
0.010
0.004
0.019
0.014
0.010
0.007
0.157
0.150
0.050
0.244
0.228
0.050
0.016
DIM PINS
D
D
D
8
14
16
MILLIMETERS
MIN
MAX
1.35
1.75
0.10
0.25
0.35
0.49
0.19
0.25
3.80
4.00
1.27
5.80
6.20
0.40
1.27
INCHES
MILLIMETERS
MIN MAX
MIN
MAX
0.189 0.197 4.80
5.00
0.337 0.344 8.55
8.75
0.386 0.394 9.80 10.00
21-0041A
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
16 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
© 1996 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.