IC for Headphone Stereos (with volume-limiting circuit) MM1336 MITSUMI IC for Headphone Stereos (with volume-limiting circuit) Monolithic IC MM1336 Outline This IC was developed for use in 3V headphone stereos. In addition to the basic functions required by headphone stereos, it incorporates a circuit for limiting volume. In some parts of Europe hearing impairment caused by the high volumes of headphone stereos has become a problem, and there has been strong demand for functions for limiting loud volumes in the sets themselves. This trend is expected to gain momentum in the U.S. as well. This IC uses an internal ALC circuit to suppress headphone stereo output, avoiding the above problem. Features 1. Configuration: Pre-and power amps, ALC circuit, motor control 2. Internal tape selector: A selector switch allows the user to select between normal and metal tapes. 3. Internal OCL circuit: There is no need for a capacitor for high-volume output, so sets can be kept thin. 4. With preamp off pin while connected to radio 5. Designed for low shock noise Reduced noise occuring when the power supply is turned on and off Package SOP-28B (MM1336CF, MM1336DF) Pin Assignment 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 SOP-28B COM1 PIN1 PNF1 PBU1 POUT1 IN1 RECT AVNF OUT1 COM2 GND1 GND2 PCOUT PHASE 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Absolute Maximum Ratings Item Operating temperature Storage temperature Power supply current Power consumption Symbol TOPR TSTG VCC Pd Ratings -20~+65 -40~+125 -0.3~+7.5 700 Units °C °C V mW VS C VCC2 OUT2 VCC1 RF Pre OFF N/M IN2 POUT2 PBU2 PNF2 PIN2 GND3 IC for Headphone Stereos (with volume-limiting circuit) MM1336 MITSUMI Recommended Operating Conditions Item Symbol Ratings Units Operating temperature TOPR -20~65 °C Operating voltage VOPR 2.0~5.0 V Electrical Characteristics (Except where noted otherwise, Vcc=3V, Ta=25°C, f=1kHz, RL1=10kΩ, RL2=16Ω) Item Consumption current Preamp unit Open-circuit gain Normal Closed-circuit gain I Metal Normal Closed-circuit gain II Metal Maximum output voltage Total harmonic distortion ratio Normal Output noise voltage Metal Crosstalk between channels Ripple rejection rate Output voltage with preamp off ALC (off) + power amp Voltage gain Voltage gain difference between channels Maximum output current Total harmonic distortion ratio Crosstalk between channels Output noise voltage Ripple rejection rate Input resistance ALC (on) + power amp Power amp output voltage ALC initiation input voltage Symbol ICC Measurement conditions VIN=0V, when motor is off Min. Typ. Max. Units 6 12 20 mA Gvo Gvc Vo=-10dBm, f=1kHz Gvc Vo=-10dBm, f=5kHz Vom THD THD=10% VOUT=-10dBm Vno C·T RR Vooff Gv GV 2CH Pom THD C·T Vn RR Ri VOA VINA ALC width WALC ALC total harmonic distortion Noise of preamp+power amp+ALC THD Vnto 31 29.5 28 23 0.30 30 Rg=2.2k, BPF (400~30kHz) 20 Rg=2.2kΩ, VOUT=-10dBm 50 VCC=3V, VR=-20dBm, fR=100Hz, Rg=2.2kΩ 45 VIN=100mVrms, Pre off POUT=5mW 72 33.5 32 30.5 25.5 0.45 0.05 75 45 70 55 -80 dB dB Vrms % 0.5 150 µVrms 100 dB dB -60 dBm 24 26 28 dB -2 0 2 dB 30 50 0.5 45 85 45 24 mW 1.5 % dB 200 µVrms dB 29 kΩ -26 THD=10% RL=16Ω POUT=5mW POUT=5mW Rg=0Ω, BPF (400~30kHz) VCC=3V, VR=-20dBm, fR=100Hz, Rg=0Ω 35 VIN=-40dBm -34 -30 -56 30 40 Input width for output from start of up to +4dB VIN=-40dBm Rg=2.2kΩ (preamp) dB 36 34.5 33 28 35 19 0.5 1.5 dBm dBm dB 1.5 6 % mVrms MITSUMI Item Motor control unit Consumption current Startup current Reference voltage IC for Headphone Stereos (with volume-limiting circuit) MM1336 Symbol Id IMS VS Reference voltage fluctuation I VS1 Reference voltage fluctuation II VS2 Reference voltage fluctuation III VS3 Output saturation voltage Bridge ratio VoSAT K Bridge ratio fluctuation I K1 Bridge ratio fluctuation II K2 Bridge ratio fluctuation III K3 Block Diagram Measurement conditions Min. Typ. Max. Units A2 measurement IM=0mA 1.5 3.5 mA At Rv=1.5Ω 500 mA At SW1=OFF, IM=100mA 0.09 0.10 0.11 V VS fluctuation rate for VCC between 1.8 and 3.5V with VCC=3.0 0.1 0.5 %/V V as reference, IM=100mA VS fluctuation rate for IM between 25 and 200 mA with 0.005 0.05 %/mA IM=100 mA as reference VS fluctuation rate for Ta between -10 and 50°C with 0.01 %/°C ° Ta=25 C as reference IM=200mA, V8 measurement, SW2=on 0.2 0.3 V V7/ V6 measurement 9 10 11 K fluctuation rate for VCC between 1.8 and 3.5V with 0.1 0.2 %/V VCC=3V as reference K fluctuation rate for IM between 25 and 250mA with 0.05 0.2 %/mA IM=100mA as reference K fluctuation rate for Ta between -10 and 60°C with 0.01 %/°C Ta=25°C as reference