Plug-in Maxi ISO Relays Power Relay F7 nPin assignment similar to ISO 7588 part 1 versions on request – 24VDC versions with contact gap >0.8mm – Integrated components (e.g. resistor, diode) – Customized marking/color – Special covers (e.g. notches, release features, brackets) nCustomized Typical applications Cross carline up to 70A for example: ABS control, cooling fan, energy management, engine control, glow plug, heated front screen, ignition, lamps: front, rear, fog light, main switch/supply relay. F134J_a_bw Contact Data Contact arrangement 1 form A, 1 form A, 1 form A, 1 NO 1 NO 1 NO Contact gap - - >0.8mm Rated voltage 12VDC 24VDC 24VDC1) Limiting continuous current 23°C 70A 70A 70A 85°C 50A 50A 50A 125°C 30A 30A 30A Limiting making current2) 240A240A240A Limiting breaking current 70A 25A 40A Limiting short-time current 3) overload current, ISO 8820-3 1.35 x 50A, 1800s 2.00 x 50A, 5s 3.50 x 50A, 0.5s 6.00 x 50A, 0.2s Jump start test, ISO 16750-1 24VDC for 5min, conducting nominal current at 23°C Contact material Silver based Min. recommended contact load4) 1A at 5VDC Initial voltage drop, form A (NO) contact at 10A, typ./max. 10/300mV Frequency of operation at nominal load 6 ops./min (0.1Hz) Operate/release time typ. 7/2ms5) Electrical endurance resistive load at 14VDC >1x105 ops. - 70A >2x105 ops. - 50A resistive load at 28VDC - >1x105ops.>1x105 ops. 25A 50A Max. DC load breaking capacity Contact Data (continued) Mechanical endurance >1x107ops. 1) Special high performance 24VDC version with contact gap >0.8mm, part number V23134-A0056-X408 (see part number table). 2) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 14VDC for 12VDC or 28VDC for 24VDC load voltages. For a load current duration of maximum 3s for a make/break ratio of 1:10. 3) Current and time are compatible with circuit protection by a typical automotive fuse. Relay will make, carry and break the specified current. 4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes/ 5) For unsuppressed relay coil. A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher risk of contact tack welding. Coil Data Rated coil voltage 12VDC, 24VDC Coil versions, DC coil Coil Rated Operate Release Coil Rated coil codevoltagevoltagevoltage resistance6)power6) VDCVDCVDC Ω±10%W 05212 7.21.690 1.6 0532414.4 3.2324 1.8 0562416.0 4.0268 2.1 0652414.4 2.4288 2.0 6) Without components in parallel. All figures are given for coil without pre-energization, at ambient temperature +23°C. Coil operating range TEVF4_OVR1 ECR0629-N Does not tak the temperat the contact c E = pre-ener Load limit curve: safe shutdown, no stationary arc/make contact. Load limit curve measured with low inductive resistors verified for 1000 switching events. 04-2013, Rev. 0413 www.te.com © 2013 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Catalog and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Does not take into account the temperature rise due to the contact current E = pre-energization. Catalog and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Catalog, product data, ‘Definitions’ section, application notes and all specifications are subject to change. 1 Plug-in Maxi ISO Relays Power Relay F7 (Continued) Insulation Data Initial dielectric strength between open contacts between contact and coil between adjacent contacts Load dump test ISO 7637-1 (12VDC), test pulse 5 ISO 7637-2 (24VDC), test pulse 5 500Vrms 500Vrms 500Vrms Vs=+86.5VDC Vs=+200VDC Other Data EU RoHS/ELV compliance compliant Protection to heat and fire according UL-94 HB or better7) Ambient temperature -40 to 125°C Climatic cycling with condensation EN ISO 6988 6 cycles, storage 8/16h Temperature cycling, IEC 60068-2-14, Nb 10 cycles, -40/+85°C (5°C/min) Damp heat cyclic, IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temp. 55°C Damp heat constant, IEC 60068-2-3, Ca 56 days Category of environmental protection, IEC 61810 RTI – dustproof, RT III – sealed Degree of protection, IEC 60529 IP54 (dustproof), IP67 (sealed) Corrosive gas IEC 60068-2-42 10±2cm3/m3 SO2, 10 days IEC 60068-2-43 1±0.3cm3/m3 H2S, 10 days Vibration resistance (functional) IEC 60068-2-6 (sine sweep) 10 to 500Hz, min. 5g8) Shock resistance (functional) IEC 60068-2-27 (half sine) 6ms, min. 30g.8) Drop test, free fall IEC 60068-2-32 1m onto concrete Other Data (continued) Terminal type Cover retention axial force pull force push force Terminal retention pull force push force resistance to bending force applied to side torque Weight Resistance to soldering heat THT IEC 60068-2-20 Packaging unit plug-in: plug-in with bracket: PCB plug-in, QC/ PCB 150N 150N 150N 100N 100N 10N8) 10N8) 0.3Nm approx. 38g (1.3oz) 260°C, 10s 210 pcs. 208 pcs. 315 pcs. 7) Refers to used materials. 8) No change in the switching state >1μs. Valid for NC contacts, NO contact values significantly higher. 8) Values apply 2mm from the end of the terminal. When the force is removed, the terminal must not have moved by more than 0.3mm. Accessories For details see datasheet Connectors for Maxi ISO Relays Terminal Assignment NO 1 form A, NO 2 NOR 1 form A, NO with resistor NOD 1 form A, NO with diode 85 87 85 87 85 87 86 30 86 30 86 30 04-2013, Rev. 0413 www.te.com © 2013 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Catalog and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Catalog and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Catalog product data, ‘Definitions’ section, application notes and all specifications are subject to change. Plug-in Maxi ISO Relays Power Relay F7 (Continued) Dimensions Power Relay F7 with quick connect terminals View of the terminals (bottom view) 25.9 ±0.3 TE1103-411 15 ±0.1 6 ±0.4 4 ±0.2 5.3 ±0.1 25.9 ±0.3 16 ±0.5 24.9 ±0.3 Measurement reference plane 4x 0.3 11 ±0.5 17 +1/-0.5 26.2 MAX. 26.2 MAX. ø 1.7 +0.2 6.3 ±0.1 25.2 MAX. 0.8 ±0.05 9.5 ±0.1 1.2 ±0.05 Quick connect terminal similar to ISO 8092-1 3.0 TE1098-Y1 1.5 TE2104-H1 TIN PLATED Power Relay F7 with PCB terminals 3.8 view) View of the terminals (bottom 26.2 MAX. 26.2 MAX. 30 86 85 2.7 87 25.2 MAX. 3.0 1.5 TIN PLATED TE2104-H1 3.8 PCB Layout Bottom view on solder pins 30 3.8 86 85 3.8 2.7 87 2x 2.18 17.9 8.4 TE2105-Q1 3.8 8.5 2x 1.93 3.8 17.0 04-2013, Rev. 0413 www.te.com © 2013 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Catalog and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Catalog and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Catalog, product data, ‘Definitions’ section, application notes and all specifications are subject to change. 3 Plug-in Maxi ISO Relays Power Relay F7 (Continued) Product code structure Typical product code V23134 -J Type V23134 Power Relay F Contact arrangement J 1 form A, 1 NO Cover 0 Standard Coil 052 12VDC 056 24VDC (contact gap >0.8mm) Terminal/arrangement D642 Plug-in/NO 1 Bracket near terminal 30 ISO 053 065 24VDC 24VDC 0 052-D642 Xnnn Customized (nnn: version number) Product code V23134-J0052-D642 V23134-J0052-X429 V23134-J0052-X439 V23134-J0052-X455 V23134-J0052-X511 V23134-J0052-X461 V23134-J0053-D642 V23134-J0056-X4082) V23134-J0065-X4974) V23134-J1052-D642 V23134-J1052-X281 V23134-J1053-D642 Arrangement Cover 1 form A, 1 NO Standard Coil suppr. Resistor 680Ω Diode (cathode 86) Resistor 470Ω Resistor 560Ω Resistor 1200Ω Bracket Resistor 560Ω Circuit1) NO NOR NOD NOR NO NOR NO NOR NO NOR NO Coil 12VDC 04-2013, Rev. 0413 www.te.com © 2013 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Catalog and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Silver based Plug-in, QC PCB Plug-in, QC3) Plug-in, QC Plug-in, QC3) PCB Plug-in, QC 24VDC 12VDC 24VDC 1) See terminal assignment diagrams. 2) Special feature: contact gap >0.8mm. 3) Special feature: 14.5mm load terminals. 4) Packed in tray with 300 pcs. per unit. Other types on request. This list represents the most common types and does not show all variants covered by this datasheet. 4 Cont. material Terminals Part number 7-1393303-3 1-1414147-0 1-1414286-0 1-1414610-0 3-1415001-2 1-1414469-0 9-1393303-7 0-1393304-5 3-1414937-3 0-1393304-9 1-1393304-0 1-1393304-1 Catalog and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Catalog product data, ‘Definitions’ section, application notes and all specifications are subject to change.