Order this document by MPX2200/D SEMICONDUCTOR TECHNICAL DATA !" ! ! " The MPX2200 and MPX2201 series device is a silicon piezoresistive pressure sensor providing a highly accurate and linear voltage output — directly proportional to the applied pressure. The sensor is a single monolithic silicon diaphragm with the strain gauge and a thin–film resistor network integrated on–chip. The chip is laser trimmed for precise span and offset calibration and temperature compensation. They are designed for use in applications such as pump/motor controllers, robotics, level indicators, medical diagnostics, pressure switching, barometers, altimeters, etc. Features • Temperature Compensated Over 0°C to + 85°C • Patented Silicon Shear Stress Strain Gauge • ± 0.25% Linearity (MPX2200D) • Easy to Use Chip Carrier Package • Available in Absolute, Differential and Gauge Configurations Application Examples • Pump/Motor Controllers • Robotics • Level Indicators • Medical Diagnostics • Pressure Switching • Barometers • Altimeters Motorola Preferred Device 0 to 200 kPa (0 to 29 psi) 40 mV FULL SCALE SPAN (TYPICAL) BASIC CHIP CARRIER ELEMENT CASE 344–15, STYLE 1 Figure 1 illustrates a block diagram of the internal circuitry on the stand–alone pressure sensor chip. DIFFERENTIAL PORT OPTION CASE 344C–01, STYLE 1 VS 3 THIN FILM TEMPERATURE COMPENSATION AND CALIBRATION CIRCUITRY X–ducer SENSING ELEMENT 2 4 NOTE: Pin 1 is the notched pin. Vout+ PIN NUMBER Vout– 1 Gnd 3 VS 2 +Vout 4 –Vout 1 GND Figure 1. Temperature Compensated Pressure Sensor Schematic VOLTAGE OUTPUT versus APPLIED DIFFERENTIAL PRESSURE The differential voltage output of the X–ducer is directly proportional to the differential pressure applied. The absolute sensor has a built–in reference vacuum. The output voltage will decrease as vacuum, relative to ambient, is drawn on the pressure (P1) side. The output voltage of the differential or gauge sensor increases with increasing pressure applied to the pressure (P1) side relative to the vacuum (P2) side. Similarly, output voltage increases as increasing vacuum is applied to the vacuum (P2) side relative to the pressure (P1) side. Preferred devices are Motorola recommended choices for future use and best overall value. Senseon and X–ducer are trademarks of Motorola, Inc. REV 7 Motorola Sensor Device Data Motorola, Inc. 1997 1 MAXIMUM RATINGS Rating Overpressure(8) (P1 > P2) Burst Pressure(8) (P1 > P2) Storage Temperature Operating Temperature Symbol Value Unit Pmax 400 kPa Pburst 2000 kPa Tstg – 40 to +125 °C TA – 40 to +125 °C OPERATING CHARACTERISTICS (VS = 10 Vdc, TA = 25°C unless otherwise noted, P1 > P2) Symbol Min Typ Max Unit Supply Voltage POP VS 0 — 200 kPa — 10 16 Supply Current Io Vdc — 6.0 — mAdc VFSS 38.5 37.5 40 40 41.5 42.5 mV Voff –1.0 – 2.0 – 3.0 — — — 1.0 2.0 3.0 mV ∆V/∆P — 0.2 — mV/kPa — – 0.25 – 1.0 – 0.5 – 2.0 — — — — 0.25 1.0 0.5 2.0 %VFSS — — ± 0.1 — — — ± 0.5 — %VFSS %VFSS TCVFSS TCVoff –1.0 — 1.0 –1.0 — 1.0 %VFSS mV Zin Zout tR 1300 — 2500 Ω 1400 — 3000 Ω — 1.0 — ms Warm–Up — — 20 — ms Offset Stability(9) — — ± 0.5 — %VFSS Symbol Min Typ Max Unit — — 2.0 — Grams — — — 690 kPa Characteristics Pressure Range(1) Full Scale Span(3) MPX2200A, MPX2200D, MPX2201D MPX2201A Offset(4) MPX2200A, MPX2200D MPX2200A MPX2201A Sensitivity Linearity(5) MPX2200D MPX2200A MPX2201D MPX2201A Pressure Hysteresis(5) (0 to 200 kPa) Temperature Hysteresis(5) (– 40°C to +125°C) Temperature Effect on Full Scale Span(5) Temperature Effect on Offset(5) Input Impedance Output Impedance Response Time(6) (10% to 90%) MECHANICAL CHARACTERISTICS Characteristics Weight, (Basic Element Case 344–15) Common Mode Line Pressure(7) NOTES: 1. 1.0 kPa (kiloPascal) equals 0.145 psi. 2. Device is ratiometric within this specified excitation range. Operating the device above the specified excitation range may induce additional error due to device self–heating. 3. Full Scale Span (VFSS) is defined as the algebraic difference between the output voltage at full rated pressure and the output voltage at the minimum rated pressure. 4. Offset (Voff) is defined as the output voltage at the minimum rated pressure. 5. Accuracy (error budget) consists of the following: • Linearity: Output deviation from a straight line relationship with pressure, using end point method, over the specified pressure range. • Temperature Hysteresis: Output deviation at any temperature within the operating temperature range, after the temperature is cycled to and from the minimum or maximum operating temperature points, with zero differential pressure applied. • Pressure Hysteresis: Output deviation at any pressure within the specified range, when this pressure is cycled to and from the minimum or maximum rated pressure, at 25°C. • TcSpan: Output deviation at full rated pressure over the temperature range of 0 to 85°C, relative to 25°C. • TcOffset: Output deviation with minimum rated pressure applied, over the temperature range of 0 to 85°C, relative to 25°C. 6. Response Time is defined as the time for the incremental change in the output to go from 10% to 90% of its final value when subjected to a specified step change in pressure. 7. Common mode pressures beyond specified may result in leakage at the case–to–lead interface. 8. Exposure beyond these limits may cause permanent damage or degradation to the device. 9. Offset stability is the product’s output deviation when subjected to 1000 hours of Pulsed Pressure, Temperature Cycling with Bias Test. 2 Motorola Sensor Device Data LINEARITY Linearity refers to how well a transducer’s output follows the equation: Vout = Voff + sensitivity x P over the operating pressure range. There are two basic methods for calculating nonlinearity: (1) end point straight line fit (see Figure 2) or (2) a least squares best line fit. While a least squares fit gives the “best case” linearity error (lower numerical value), the calculations required are burdensome. Conversely, an end point fit will give the “worst case” error (often more desirable in error budget calculations) and the calculations are more straightforward for the user. Motorola’s specified pressure sensor linearities are based on the end point straight line method measured at the midrange pressure. LEAST SQUARES FIT RELATIVE VOLTAGE OUTPUT EXAGGERATED PERFORMANCE CURVE LEAST SQUARE DEVIATION STRAIGHT LINE DEVIATION END POINT STRAIGHT LINE FIT OFFSET 50 PRESSURE (% FULLSCALE) 0 100 Figure 2. Linearity Specification Comparison ON–CHIP TEMPERATURE COMPENSATION and CALIBRATION Figure 3 shows the output characteristics of the MPX2200 series at 25°C. The output is directly proportional to the differential pressure and is essentially a straight line. VS = 10 Vdc TA = 25°C P1 > P2 40 OUTPUT (mVdc) 35 TYP 30 25 The effects of temperature on Full Scale Span and Offset are very small and are shown under Operating Characteristics. SPAN RANGE (TYP) MAX 20 15 10 MIN 5 0 –5 kPa 0 PSI 25 50 7.25 75 100 14.5 125 150 21.75 175 200 29 OFFSET PRESSURE Figure 3. Output versus Pressure Differential SILICONE GEL DIE COAT DIFFERENTIAL/GAUGE STAINLESS STEEL DIE METAL COVER P1 EPOXY CASE ÉÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉ WIRE BOND LEAD FRAME DIFFERENTIAL/GAUGE ELEMENT P2 DIE BOND SILICONE GEL ABSOLUTE DIE COAT DIE P1 STAINLESS STEEL METAL COVER EPOXY CASE ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ WIRE BOND LEAD FRAME ABSOLUTE ELEMENT P2 DIE BOND Figure 4. Cross–Sectional Diagrams (Not to Scale) Figure 4 illustrates an absolute sensing die (right) and the differential or gauge die in the basic chip carrier (Case 344–15). A silicone gel isolates the die surface and wire bonds from the environment, while allowing the pressure signal to be transmitted to the silicon diaphragm. The MPX2200 series pressure sensor operating charac- Motorola Sensor Device Data teristics and internal reliability and qualification tests are based on use of dry air as the pressure media. Media other than dry air may have adverse effects on sensor performance and long term reliability. Contact the factory for information regarding media compatibility in your application. 3 PRESSURE (P1)/VACUUM (P2) SIDE IDENTIFICATION TABLE Motorola designates the two sides of the pressure sensor as the Pressure (P1) side and the Vacuum (P2) side. The Pressure (P1) side is the side containing the silicone gel which isolates the die from the environment. The differential or gauge sensor is designed to operate with positive differen- tial pressure applied, P1 > P2. The absolute sensor is designed for vacuum applied to P1 side. The Pressure (P1) side may be identified by using the table below: Part Number MPX2200A MPX2200D MPX2200DP MPX2200AP Case Type MPX2201DP MPX2200GP MPX2201GP MPX2200GVP MPX2200AS MPX2200GS MPX2200GVS MPX2200ASX MPX2200GSX MPX2201GSX Pressure (P1) Side Identifier 344–15– Stainless Steel Cap 344C–01 Side with Part Marking 344B–01 Side with Port Attached 344D–01 Stainless Steel Cap 344E–01 Side with Port Attached 344A–01 Stainless Steel Cap 344F–01 Side with Port Attached ORDERING INFORMATION MPX2200 series pressure sensors are available in absolute, differential and gauge configurations. Devices are available in the basic element package or with pressure port fittings which provide printed circuit board mounting ease and barbed hose pressure connections. MPX Series D i T Device Type O i Options C Case Type T Order Number Device Marking Basic Element Absolute, Differential Case 344–15 MPX2200A MPX2200D MPX2200A MPX2200D Ported Elements Differential Case 344C–01 MPX2200DP MPX2201DP MPX2200DP MPX2201DP Absolute, Gauge Case 344B–01 MPX2200AP MPX2200GP MPX2201GP MPX2200AP MPX2200GP MPX2201GP Gauge Vacuum Case 344D–01 MPX2200GVP MPX2200GVP Absolute, Gauge Stove Pipe Case 344E–01 MPX2200AS MPX2200GS MPX2200A MPX2200D Gauge Vacuum Stove Pipe Case 344A–01 MPX2200GVS MPX2200D Absolute, Gauge Axial Case 344F–01 MPX2200ASX MPX2200GSX MPX2201GSX MPX2200A MPX2200D MPX2201D 4 Motorola Sensor Device Data PACKAGE DIMENSIONS NOTES: C 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION –A– IS INCLUSIVE OF THE MOLD STOP RING. MOLD STOP RING NOT TO EXCEED 16.00 (0.630). POSITIVE PRESSURE (P1) R M B –A– DIM A B C D F G J L M N R N 1 PIN 1 2 3 L 4 –T– SEATING PLANE J POSITIVE PRESSURE (P1) G F D 4 PL 0.136 (0.005) M T A M INCHES MIN MAX 0.595 0.630 0.514 0.534 0.200 0.220 0.016 0.020 0.048 0.064 0.100 BSC 0.014 0.016 0.695 0.725 30_ NOM 0.475 0.495 0.430 0.450 STYLE 1: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 15.11 16.00 13.06 13.56 5.08 5.59 0.41 0.51 1.22 1.63 2.54 BSC 0.36 0.40 17.65 18.42 30_ NOM 12.07 12.57 10.92 11.43 GROUND + OUTPUT + SUPPLY – OUTPUT CASE 344–15 ISSUE W PORT #2 VACUUM PRESSURE (P2) –B– C NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. A POSITIVE PRESSURE (P1) PIN 1 V 1 2 3 4 K J N R SEATING PLANE S –T– G F D 4 PL 0.13 (0.005) M T B M DIM A B C D F G J K N R S V INCHES MIN MAX 0.690 0.720 0.245 0.255 0.780 0.820 0.016 0.020 0.048 0.064 0.100 BSC 0.014 0.016 0.345 0.375 0.300 0.310 0.178 0.186 0.220 0.240 0.182 0.194 STYLE 1: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 17.53 18.28 6.22 6.48 19.81 20.82 0.41 0.51 1.22 1.63 2.54 BSC 0.36 0.41 8.76 9.53 7.62 7.87 4.52 4.72 5.59 6.10 4.62 4.93 GROUND + OUTPUT + SUPPLY – OUTPUT CASE 344A–01 ISSUE B Motorola Sensor Device Data 5 PACKAGE DIMENSIONS — CONTINUED SEATING PLANE NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5, 1982. 2. CONTROLLING DIMENSION: INCH. –A– –T– U L R H N PORT #1 POSITIVE PRESSURE (P1) –Q– B 1 2 3 4 PIN 1 K –P– 0.25 (0.010) T Q M S S J F G D 4 PL 0.13 (0.005) C M T S S Q S INCHES MIN MAX 1.145 1.175 0.685 0.715 0.305 0.325 0.016 0.020 0.048 0.064 0.100 BSC 0.182 0.194 0.014 0.016 0.695 0.725 0.290 0.300 0.420 0.440 0.153 0.159 0.153 0.159 0.230 0.250 0.220 0.240 0.910 BSC DIM A B C D F G H J K L N P Q R S U STYLE 1: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 29.08 29.85 17.40 18.16 7.75 8.26 0.41 0.51 1.22 1.63 2.54 BSC 4.62 4.93 0.36 0.41 17.65 18.42 7.37 7.62 10.67 11.18 3.89 4.04 3.89 4.04 5.84 6.35 5.59 6.10 23.11 BSC GROUND + OUTPUT + SUPPLY – OUTPUT CASE 344B–01 ISSUE B PORT #1 R NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. –A– U V W L H PORT #2 N PORT #1 POSITIVE PRESSURE (P1) PORT #2 VACUUM (P2) –Q– B SEATING PLANE SEATING PLANE 1 2 3 4 PIN 1 K –P– –T– –T– 0.25 (0.010) M T Q S S F J G D 4 PL C 0.13 (0.005) M T S S Q S DIM A B C D F G H J K L N P Q R S U V W INCHES MIN MAX 1.145 1.175 0.685 0.715 0.405 0.435 0.016 0.020 0.048 0.064 0.100 BSC 0.182 0.194 0.014 0.016 0.695 0.725 0.290 0.300 0.420 0.440 0.153 0.159 0.153 0.159 0.063 0.083 0.220 0.240 0.910 BSC 0.248 0.278 0.310 0.330 STYLE 1: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 29.08 29.85 17.40 18.16 10.29 11.05 0.41 0.51 1.22 1.63 2.54 BSC 4.62 4.93 0.36 0.41 17.65 18.42 7.37 7.62 10.67 11.18 3.89 4.04 3.89 4.04 1.60 2.11 5.59 6.10 23.11 BSC 6.30 7.06 7.87 8.38 GROUND + OUTPUT + SUPPLY – OUTPUT CASE 344C–01 ISSUE B 6 Motorola Sensor Device Data PACKAGE DIMENSIONS — CONTINUED NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5, 1982. 2. CONTROLLING DIMENSION: INCH. –A– U L SEATING PLANE –T– R DIM A B C D F G H J K L N P Q R S U H PORT #2 VACUUM (P2) POSITIVE PRESSURE (P1) N –Q– B 1 2 3 4 K PIN 1 S C J F –P– 0.25 (0.010) M T Q G D 4 PL 0.13 (0.005) S M T S S Q S INCHES MIN MAX 1.145 1.175 0.685 0.715 0.305 0.325 0.016 0.020 0.048 0.064 0.100 BSC 0.182 0.194 0.014 0.016 0.695 0.725 0.290 0.300 0.420 0.440 0.153 0.159 0.153 0.158 0.230 0.250 0.220 0.240 0.910 BSC STYLE 1: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 29.08 29.85 17.40 18.16 7.75 8.26 0.41 0.51 1.22 1.63 2.54 BSC 4.62 4.93 0.36 0.41 17.65 18.42 7.37 7.62 10.67 11.18 3.89 4.04 3.89 4.04 5.84 6.35 5.59 6.10 23.11 BSC GROUND + OUTPUT + SUPPLY – OUTPUT CASE 344D–01 ISSUE B PORT #1 POSITIVE PRESSURE (P1) –B– C NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. A BACK SIDE VACUUM (P2) DIM A B C D F G J K N R S V V 4 3 2 1 PIN 1 K J N R SEATING PLANE S –T– INCHES MIN MAX 0.690 0.720 0.245 0.255 0.780 0.820 0.016 0.020 0.048 0.064 0.100 BSC 0.014 0.016 0.345 0.375 0.300 0.310 0.178 0.186 0.220 0.240 0.182 0.194 MILLIMETERS MIN MAX 17.53 18.28 6.22 6.48 19.81 20.82 0.41 0.51 1.22 1.63 2.54 BSC 0.36 0.41 8.76 9.53 7.62 7.87 4.52 4.72 5.59 6.10 4.62 4.93 G F D 4 PL 0.13 (0.005) M T B M STYLE 1: PIN 1. 2. 3. 4. GROUND + OUTPUT + SUPPLY – OUTPUT CASE 344E–01 ISSUE B Motorola Sensor Device Data 7 PACKAGE DIMENSIONS — CONTINUED –T– C A E –Q– U N V B R PORT #1 POSITIVE PRESSURE (P1) PIN 1 –P– 0.25 (0.010) M T Q M 4 3 2 1 S K F J NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. DIM A B C D E F G J K N P Q R S U V INCHES MIN MAX 1.080 1.120 0.740 0.760 0.630 0.650 0.016 0.020 0.160 0.180 0.048 0.064 0.100 BSC 0.014 0.016 0.220 0.240 0.070 0.080 0.150 0.160 0.150 0.160 0.440 0.460 0.695 0.725 0.840 0.860 0.182 0.194 MILLIMETERS MIN MAX 27.43 28.45 18.80 19.30 16.00 16.51 0.41 0.51 4.06 4.57 1.22 1.63 2.54 BSC 0.36 0.41 5.59 6.10 1.78 2.03 3.81 4.06 3.81 4.06 11.18 11.68 17.65 18.42 21.34 21.84 4.62 4.92 G D 4 PL 0.13 (0.005) M T P S Q S STYLE 1: PIN 1. 2. 3. 4. GROUND V (+) OUT V SUPPLY V (–) OUT CASE 344F–01 ISSUE B Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315 Mfax: [email protected] – TOUCHTONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, – US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 INTERNET: http://motorola.com/sps 8 ◊ Motorola Sensor DeviceMPX2200/D Data