MOTOROLA MSC8101

Freescale Semiconductor
Technical Data
MSC8101
Rev. 16, 11/2004
MSC8101
Network Digital Signal Processor
MII
•
TDMs
{ ••
SIU
MCC / UART / HDLC / Transparent /
Ethernet / Fast Ethernet / ATM / SCC
UTOPIA
Interface
Serial Interface and TSA
CPM
3 × FCC
2 × MCC
64-bit System Bus
Interrupt
Controller
MEMC
Timers
Parallel I/O
4 × SCC
Baud Rate
Generators
2 × SMC
Dual Ported
RAM
DMA
Engine
2 × SDMA
I2C
RISC
Interrupts
64-bit Local Bus
Other
Peripherals
Extended Core
Address
Register
File
Data ALU
Register
File
Q2PPC
Bridge
128-bit QBus
SIC
MEMC
PIC
Interrupts
EFCOP
Boot
ROM
HDI16
SC140
Core
JTAG
Address
ALU
Data
ALU
SRAM
512 KB
L1 Interface
EOnCE™
Power
Management
64/32-bit
System
Bus
SIC_EXT
Bridge
SPI
Program
Sequencer
PIT
System Protection
Reset Control
Clock Control
The Freescale MSC8101
16-bit DSP is the first
member of the family of
DSPs based on the
StarCore SC140 DSP core.
The MSC8101 is available
in three core speed levels:
250, 275, and 300 MHz.
Clock/PLL
128-bit P-Bus
64-bit XA Data Bus
64-bit XB Data Bus
8/16-bit
Host
Interface
What’s New?
Rev. 16 includes the following
changes:
• Changed most REFCLK
references to DLLIN in
Section 2.7.4.
Figure 1. MSC8101 Block Diagram
The Freescale MSC8101 DSP is a very versatile device that integrates the high-performance SC140 four-ALU (arithmetic
logic unit) DSP core along with 512 KB of internal memory, a communications processor module (CPM), a 64-bit bus, a very
flexible System Integration Unit (SIU), and a 16-channel DMA engine on a single device. With its four-ALU core, the
MSC8101 can execute up to four multiply-accumulate (MAC) operations in a single clock cycle. The MSC8101 CPM is a 32bit RISC-based communications protocol engine that can network to time-division multiplexed (TDM) highways, Ethernet,
and asynchronous transfer mode (ATM) backbones. The MSC8101 60x-compatible bus interface facilitates its connection to
multi-master system architectures. The very large internal memory, 512 KB, reduces the need for external program and data
memories. The MSC8101 offers 1500 DSP MMACS (1200 core and 300 EFCOP) performance using an internal 300 MHz
clock with a 1.6 V core and independent 3.3 V input/output (I/O).
© Freescale Semiconductor, Inc., 2001, 2004. All rights reserved.
Table of Contents
MSC8101 Features .................................................................................................................................................................................... iii
Target Applications .....................................................................................................................................................................................iv
Product Documentation ..............................................................................................................................................................................iv
Chapter 1
Signals/Connections
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
Chapter 2
Physical and Electrical Specifications
2.1
2.2
2.3
2.4
2.5
2.6
Chapter 3
Absolute Maximum Ratings .................................................................................................................................................. 2-1
Recommended Operating Conditions.................................................................................................................................... 2-2
Thermal Characteristics ......................................................................................................................................................... 2-2
DC Electrical Characteristics................................................................................................................................................. 2-3
Clock Configuration .............................................................................................................................................................. 2-4
AC Timings............................................................................................................................................................................ 2-7
Packaging
3.1
3.2
Chapter 4
Power Signals ........................................................................................................................................................................ 1-4
Clock Signals ......................................................................................................................................................................... 1-4
Reset, Configuration, and EOnCE Event Signals.................................................................................................................. 1-5
System Bus, HDI16, and Interrupt Signals............................................................................................................................ 1-6
Memory Controller Signals ................................................................................................................................................. 1-13
CPM Ports............................................................................................................................................................................ 1-15
JTAG Test Access Port Signals............................................................................................................................................ 1-36
Reserved Signals.................................................................................................................................................................. 1-36
FC-PBGA Package Description............................................................................................................................................. 3-1
Lidded FC-PBGA Package Mechanical Drawing ............................................................................................................... 3-31
Design Considerations
4.1
4.2
4.3
4.4
Thermal Design Considerations............................................................................................................................................. 4-1
Electrical Design Considerations........................................................................................................................................... 4-1
Power Considerations ............................................................................................................................................................ 4-2
Layout Practices..................................................................................................................................................................... 4-3
Ordering and Contact Information ...............................................................................................................................Back Cover
Data Sheet Conventions
pin and pinout
Although the device package does not have pins, the term pins and pin-out are used for
convenience and indicate specific signal locations within the ball-grid array.
OVERBAR
Used to indicate a signal that is active when pulled low (For example, the RESET pin is active
when low.)
“asserted”
Means that a high true (active high) signal is high or that a low true (active low) signal is low
“deasserted”
Means that a high true (active high) signal is low or that a low true (active low) signal is high
Examples:
Signal/Symbol
Logic State
Signal State
Voltage
PIN
True
Asserted
VIL/VOL
PIN
False
Deasserted
VIH/VOH
PIN
True
Asserted
VIH/VOH
PIN
False
Deasserted
VIL/VOL
Note: Values for VIL, VOL, V IH, and VOH are defined by individual product specifications.
MSC8101 Technical Data, Rev. 16
ii
Freescale Semiconductor
MSC8101 Features
•
•
•
•
•
•
•
•
•
•
•
•
SC140 core
— Architecture optimized for efficient C/C++ code compilation
— Four 16-bit ALUs and two 32-bit AGUs
— 1200 DSP MMACS running at 300 MHz
— Very low power dissipation
— Variable-length execution set (VLES) execution model
— JTAG/Enhanced OnCE debug port
Communications processor module (CPM)
— Programmable protocol machine using a 32-bit RISC engine
— 155 Mbps ATM interface (including AAL 0/1/2/5)
— 10/100 Mbit Ethernet interface
— Up to four E1/T1 interfaces or one E3/T3 interface and one E1/T1 interface
— HDLC support up to T3 rates, or 256 channels
64- or 32-bit wide bus interface
— Support for bursts for high efficiency
— Glueless interface to 60x-compatible bus systems
— Multi-master support
Enhanced filter coprocessor (EFCOP)
— Independently and concurrently executes long filters (such as echo cancellation)
— Runs at 250/275/300 MHz and provides 250/275/300 MMACS performance
Programmable memory controller
— Control for up to eight banks of external memory
— User-programmable machines (UPM) allowing glueless interface to various memory types (SRAM, DRAM,
EPROM, and Flash memory) and other user-definable peripherals
— Dedicated pipelined SDRAM memory interface
Large internal SRAM
— 256K 16-bit words (512 KB)
— Unified program and data space configurable by the application
— Word and byte addressable
DMA controller
— 16 DMA channels, FIFO based, with burst capabilities
— Sophisticated addressing capabilities
Small foot print package
— 17 mm × 17 mm lidded FC-PBGA package
Very low power consumption
— Separate power supply for internal logic (1.6 V) and for I/O (3.3 V)
Enhanced 16-bit parallel host interface (HDI16)
— Supports a variety of microcontroller, microprocessor, and DSP bus interfaces
Phase-lock loops (PLLs)
— System PLL
— CPM DPLLs (SCC and SCM)
Process technology
— 0.13 micron copper interconnect process technology
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
iii
Target Applications
The MSC8101 targets applications requiring very high performance, very large amounts of internal memory, and
such networking capabilities as:
•
•
•
•
Third-generation wideband wireless infrastructure systems
Packet Telephony systems
Multi-channel modem banks
Multi-channel xDSL
Product Documentation
The documents listed in Table 1 are required for a complete description of the MSC8101 and are necessary to
design properly with the part. Documentation is available from the following sources (see back cover for details):
•
•
•
•
A local Freescale distributor
A Freescale Semiconductor sales office
A Freescale Semiconductor Literature Distribution Center
The world wide web (WWW)
Table 1. MSC8101 Documentation
Name
Description
Order Number
MSC8101
Technical Data
MSC8101 features list and physical, electrical, timing, and package
specifications
MSC8101/D
MSC8101 User’s Guide
Detailed functional description of the MSC8101 memory
configuration, operation, and register programming
MSC8101UG/D
MSC8101 Pocket Guide
Quick reference information for application development.
MSC8101PG/D
MSC8101 Reference Manual
Detailed description of the MSC8101 processor core and instruction
set
MSC8101RM/D
SC140 DSP Core Reference Manual
Detailed description of the SC140 family processor core and
instruction set
MNSC140CORE/D
Application Notes
Documents describing specific applications or optimized device
operation including code examples
See the MSC8101 product
website
MSC8101 Technical Data, Rev. 16
iv
Freescale Semiconductor
1
Signals/Connections
The MSC8101 external signals are organized into functional groups, as shown in Table 1-1, Figure 1-1, and
Figure 1-2. Table 1-1 lists the functional groups, states the number of signal connections in each group, and
references the table that gives details on multiplexed signals within each group. Figure 1-1 shows MSC8101
external signals organized by function. Figure 1-2 indicates how the parallel input/output (I/O) ports signals are
multiplexed. Because the parallel I/O design supported by the MSC8101 communications processor module
(CPM) is a subset of the parallel I/O signals supported by the MPC8260 device, port pins are not numbered
sequentially.
Table 1-1.
MSC8101 Functional Signal Groupings
Number of Signal
Connections
Detailed Description
Power (VCC , VDD, and GND)
80
Table 1-2 on page 1-4
Clock
6
Table 1-3 on page 1-4
Reset, configuration, and EOnCE
11
Table 1-4 on page 1-5
133
Table 1-5 on page 1-7
27
Table 1-6 on page 1-13
Port A
26
Table 1-7 on page 1-16
Port B
14
Table 1-8 on page 1-21
Port C
18
Table 1-9 on page 1-24
Port D
8
Table 1-10 on page 1-33
JTAG Test Access Port
5
Table 1-11 on page 1-36
Reserved (denotes connections that are always reserved)
5
Table 1-12 on page 1-36
Functional Group
System bus, HDI16, and interrupts
Memory Controller
CPM Input/Output Parallel Ports
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
1-1
Signals/Connections
For the signals
multiplexed on
Ports A–D,
see Figure 1-2
VDD
VDDH
VCCSYN
VCCSYN1
→ 14
→ 25
→ 1
→ 1
GND
GNDSYN
GNDSYN1
→ 37
→ 1
→ 1
Port A
PA[31–6]
↔ 26
Port B
PB[31–18]
↔ 14
Port C
PC[31–22, 15–12, 7–4]
↔ 18
Port D
PD[31–29, 19–16, 7]
TMS
TDI
TCK
TRST
TDO
EOnCE Event
EED
EE0
EE1
EE[2–3]
EE[4–5]
BNKSEL[0–2]
TC[0–2]
→
→
→
→
←
8
1
1
1
1
1
C
P
M
I
/
O
P
O
R
T
S
6
0
x
B
U
S
J
T
A
G
RESET
Configuration
DBREQ
HPE
BTM[0–1]
PORESET
RSTCONF
HRESET
SRESET
↔
↔
↔
↔
↔
→
→
↔
↔
1
1
1
2
2
1
1
1
1
↔
↔
↔
↔
↔
→
↔
↔
↔
↔
↔
←
↔
↔
↔
16
4
1
↔ D[32–47]
↔ D[48–51]
↔ D52
1
1
↔ D53
↔ D54
1
1
1
1
1
1
4
↔
↔
↔
↔
↔
↔
↔
1
← Reserved
DP0
Reserved
1
↔ IRQ1
DP1
IRQ1
EXT_BG2
1
1
1
1
1
1
1
1
1
1
1
1
↔
↔
↔
↔
↔
↔
↔
↔
←
→
↔
↔
DP2
DP3
DP4
DP5
DP6
DP7
Reserved
Reserved
DREQ3
DREQ4
DACK3
DACK4
EXT_DBG2
EXT_BR3
EXT_BG3
EXT_DBG3
IRQ6
IRQ7
PSDRAS
PBS[0–7]
PGPL0
PGPL1
PGPL2
PGPL3
PGPL4
PGPL5
A[0–31]
TT[0–4]
TSIZ[0–3]
TBST
IRQ1
Reserved
BR
BG
ABB
TS
AACK
ARTRY
DBG
DBB
D[0–31]
D55
D56
D57
D58
D59
D60
D[61–63]
IRQ2
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
TA
TEA
NMI
NMI_OUT
PSDVAL
IRQ7
CLKIN
→
1
8
1
→ CS[0–7]
→ BCTL1
MODCK[1–3]
→
3
2
→ BADDR[27–28]
CLKOUT
DLLIN
←
→
1
1
1
1
8
1
1
1
1
1
1
→
→
→
→
→
→
→
↔
→
TEST
THERM[1–2]
SPARE1, SPARE5
Note:
↔
P
O
W
E
R
32
5
4
1
1
3
1
1
1
1
1
1
1
1
32
→
↔
↔
1
2
2
M
E
M
C
ALE
BCTL0
PWE[0–7]
PSDA10
PSDWE
POE
PSDCAS
PGTA
PSDAMUX
GBL
BADDR[29–31]
IRQ[2–3, 5]
IRQ2
IRQ3
HDI16 Signals
HD[0–15]
HA[0–3]
HCS1
Single DS
Double DS
HRW
HRD/HRD
HDS/HDS
HWR/HWR
Single HR
Double HR
HREQ/HREQ
HTRQ/HTRQ
HACK/HACK
HRRQ/HRRQ
HDSP
HDDS
H8BIT
HCS2
Reserved
EXT_Br2
INT_OUT
PSDDQM[0–7]
PUPMWAIT
PPBS
Refer to the System Interface Unit (SIU) chapter in the MSC8101 Reference Manual for details on how to configure these pins.
Figure 1-1.
MSC8101 External Signals
MSC8101 Technical Data, Rev. 16
1-2
Freescale Semiconductor
FCC1
ATM/UTOPIA
MPHY
MPHY
Master
Master
mux poll
dir. poll
or Slave
TXENB
TXCLAV TXCLAV0
TXSOC (master)
RXENB
RXSOC
(slave)
RXCLAV RXCLAV0
TXD0
TXD1
TXD2
TXD3
TXD4
TXD5
TXD6
TXD7
RXD7
RXD6
RXD5
RXD4
RXD3
RXD2
RXD1
RXD0
FCC1
HDLC/
Ethernet transp. HDLC
MII
Serial Nibble
COL
GPIO
PA31
CRS
TX_ER
TX_EN
PA30
PA29
PA28
RTS
RX_DV
PA27
RX_ER
TXD3
TXD2
TXD1
TXD0
RXD0
RXD1
RXD2
RXD3
SDMA
MSNUM0
MSNUM1
TXD
RXD
TXD3
TXD2
TXD1
TXD0
RXD0
RXD1
RXD2
RXD3
SMC2
SMTXD
SMRXD
FCC2
HDLC/
HDLC
Ethernet
transp.
MII
Serial Nibble
TX_ER
RX_DV
TX_EN
RX_ER
RTS
SMSYN
SCC2
RXD
TXD
CRS
TXD3
TXD2
L1TSYNC
SI2
PA7
L1RSYNC
TDMB2
L1TXD
L1RXD
L1RSYNC
L1TSYNC
TDMC2
L1TXD
L1RXD
L1TSYNC
L1RSYNC
TDMD2
L1TXD
L1RXD
L1TSYNC
L1RSYNC
PA6
PB31
PB30
PB29
PB28
RTS/TENA
TXD3
TXD2
L1TXD3
L1RXD3
TXD1
L1RXD2
TXD0
RXD0
RXD1
RXD2
RXD3
L1RXD1
L1TXD2
L1TXD1
TXD1
TXD
RXD
MSNUM2
MSNUM3
MSNUM4
MSNUM5
SI1
TDMA1
Serial
Nibble
L1TXD
L1TXD0
L1RXD
L1RXD0
COL
TXD0
RXD0
RXD1
RXD2
RXD3
PB27
PB26
PB25
PB24
PB23
I2C
SDA
SCL
Ext. Req.
EXT1
SCC1
CTS/CLSN
Ext. Req.
DREQ2
EXT2
SCC1
DACK1
DREQ1
CTS
CD
SMC1
SMTXD
SMRXD
CTS
CD
RXD
TXD
RTS/TENA
CLK7
TIN4
PC25
CLK8
TIN3/
TOUT4
PC24
BRG8O
CLK9
CLK10
PC23
PC22
PC15
PC14
PC13
PC12
LIST1
PC7
LIST2
PC6
LIST3
LIST4
PC5
PC4
PD31
PD30
PD29
PD19
PD18
PD17
PD16
PD7
DRACK1/DONE1
DRACK2/DONE2
SPI
BRG1O
SPISEL
SPICLK
SPIMOSI
BRG2O
SPIMISO
SMSYN
Figure 1-2.
PC29
BRG7O
LIST2
LIST4
LIST3
CTS/CLSN
CD/RENA
TIN2
BRG5O
BRG6O
SMTXD
CTS/CLSN
CD/RENA
FCC2
RXADDR3 RXCLAV2
TXADDR4 TXCLAV3
RXADDR4 RXCLAV3
RXPRTY
TXPRTY
TXADDR3 TXCLAV2
LIST1
CLK3
TIN1/
CLK4
PC28
TOUT2
CLK5 TGATE2 PC27
CLK6 TOUT3 PC26
SIU Timer Input BRG4O
CLK5
TMCLK
DMA
DACK2
FCC1
PB22
PB21
PB20
PB19
BRGs Clocks Timers PB18
BRG1O CLK1 TGATE1 PC31
BRG2O CLK2 TOUT1 PC30
BRG3O
CTS/CLSN
TXADDR0
RXADDR0
TXADDR1
RXADDR1
TXADDR2/
TXADDR2
TXCLAV1
RXADDR2/
RXADDR2
RXCLAV1
PA26
PA25
PA24
PA23
PA22
PA21
PA20
PA19
PA18
PA17
PA16
PA15
PA14
PA13
PA12
PA11
PA10
PA9
PA8
CPM Port A–D Pin Multiplexed Functionality
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
1-3
Signals/Connections
1.1 Power Signals
Table 1-2.
Power and Ground Signal Inputs
Power Name
Description
VDD
Internal Logic Power
VDD dedicated for use with the device core. The voltage should be well-regulated and the input should be provided with
an extremely low impedance path to the VDD power rail.
VDDH
Input/Output Power
This source supplies power for the I/O buffers. The user must provide adequate external decoupling capacitors.
VCCSYN
System PLL Power
VCC dedicated for use with the system Phase Lock Loop (PLL). The voltage should be well-regulated and the input
should be provided with an extremely low impedance path to the VCC power rail.
VCCSYN1
SC140 PLL Power
VCC dedicated for use with the SC140 core PLL. The voltage should be well-regulated and the input should be provided
with an extremely low impedance path to the V CC power rail.
GND
System Ground
An isolated ground for the internal processing logic. This connection must be tied externally to all chip ground
connections, except GND SYN and GND SYN1. The user must provide adequate external decoupling capacitors.
GNDSYN
System PLL Ground
Ground dedicated for system PLL use. The connection should be provided with an extremely low-impedance path to
ground.
GNDSYN1
SC140 PLL Ground 1
Ground dedicated for SC140 core PLL use. The connection should be provided with an extremely low-impedance path
to ground.
1.2 Clock Signals
Table 1-3.
Signal Name
Type
Clock Signals
Signal Description
CLKIN
Input
Clock In
Primary clock input to the MSC8101 PLL.
MODCK1
Input
Clock Mode Input 1
Defines the operating mode of internal clock circuits.
TC0
Output
Transfer Code 0
Supplies information that can be useful for debugging bus transactions initiated by the MSC8101.
BNKSEL0
Output
MODCK2
Input
Clock Mode Input 2
Defines the operating mode of internal clock circuits.
TC1
Output
Transfer Code 1
Supplies information that can be useful for debugging bus transactions initiated by the MSC8101.
BNKSEL1
Output
MODCK3
Input
Clock Mode Input 3
Defines the operating mode of internal clock circuits.
TC2
Output
Transfer Code 2
Supplies information that can be useful for debugging bus transactions initiated by the MSC8101.
BNKSEL2
Output
Bank Select 0
Selects the SDRAM bank when the MSC8101 is in 60x-compatible bus mode.
Bank Select 1
Selects the SDRAM bank when the MSC8101 is in 60x-compatible bus mode.
Bank Select 2
Selects the SDRAM bank when the MSC8101 is in 60x-compatible bus mode.
MSC8101 Technical Data, Rev. 16
1-4
Freescale Semiconductor
Reset, Configuration, and EOnCE Event Signals
Table 1-3.
Signal Name
Clock Signals (Continued)
Type
Signal Description
CLKOUT
Output
Clock Out
The system bus clock.
DLLIN
Input
DLLIN
Synchronizes with an external device.
Note:
When the DLL is disabled, connect this signal to GND.
1.3 Reset, Configuration, and EOnCE Event Signals
Table 1-4.
Signal Name
DBREQ
Type
Input
EE01
Signal Description
Debug Request
Determines whether to go into SC140 Debug mode when PORESET is deasserted.
Enhanced OnCE (EOnCE) Event 0
After PORESET is deasserted, you can configure EE0 as an input (default) or an output.
Input
Output
HPE
Reset, Configuration, and EOnCE Event Signals
Input
EE11
Debug request, enable Address Event Detection Channel 0, or generate an EOnCE event.
Detection by Address Event Detection Channel 0. Used to trigger external debugging equipment.
Host Port Enable
When this pin is asserted during PORESET, the Host port is enabled, the system data bus is 32 bits
wide, and the Host must program the reset configuration word.
EOnCE Event 1
After PORESET is deasserted, you can configure EE1 as an input (default) or an output.
Input
Output
EE21
Enable Address Event Detection Channel 1 or generate an EOnCE event.
Debug Acknowledge or detection by Address Event Detection Channel 1. Used to trigger external
debugging equipment.
EOnCE Event 2
After PORESET is deasserted, you can configure EE2 as an input (default) or an output.
Input
Output
EE31
Enable Address Event Detection Channel 2 or generate an EOnCE event or enable the Event
Counter.
Detection by Address Event Detection Channel 2. Used to trigger external debugging equipment.
EOnCE Event 3
After PORESET is deasserted, you can configure EE3 as an input (default) or an output. See the
emulation and debug chapter in the SC140 DSP Core Reference Manual for details on the ERCV
Register.
Input
Output
Enable Address Event Detection Channel 3 or generate one of the EOnCE events.
The DSP has read the EOnCE Receive Register (ERCV). Triggers external debugging equipment.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
1-5
Signals/Connections
Table 1-4.
Signal Name
BTM[0–1]
Reset, Configuration, and EOnCE Event Signals (Continued)
Type
Signal Description
Input
Boot Mode 0–1
Determines the MSC8101 boot mode when PORESET is deasserted. See the emulation and debug
chapter in the SC140 DSP Core Reference Manual for details on how to set these pins.
EE41
EOnCE Event 4
After PORESET is deasserted, you can configure EE4 as an input (default) or an output. See the
emulation and debug chapter in the SC140 DSP Core Reference Manual for details on the ETRSMT
Register.
Input
Output
EE51
Enable Address Event Detection Channel 4 or generate an EOnCE event.
The DSP wrote the EOnCE Transmit Register (ETRSMT). Triggers external debugging equipment.
EOnCE Event 5
After PORESET is deasserted, you can configure EE5 as an input (default) or an output.
Input
Output
EED1
Enable Address Event Detection Channel 5.
Detection by Address Event Detection Channel 5. Triggers external debugging equipment.
Enhanced OnCE (EOnCE) Event Detection
After PORESET is deasserted, you can configure EED as an input (default) or output:
Input
Output
Enable the Data Event Detection Channel.
Detection by the Data Event Detection Channel. Triggers external debugging equipment.
PORESET
Input
Power-On Reset
When asserted, this line causes the MSC8101 to enter power-on reset state.
RSTCONF
Input
Reset Configuration
Used during reset configuration sequence of the chip. A detailed explanation of its function is
provided in the “Power-On Reset Flow” and “Hardware Reset Configuration” sections of the
MSC8101 Reference Manual.
HRESET
Input
Hard Reset
When asserted, this open-drain line causes the MSC8101 to enter the hard reset state.
SRESET
Input
Soft Reset
When asserted, this open-drain line causes the MSC8101 to enter the soft reset state.
Note:
See the emulation and debug chapter in the SC140 DSP Core Reference Manual for details on how to configure these pins.
1.4 System Bus, HDI16, and Interrupt Signals
The system bus, HDI16, and interrupt signals are grouped together because they use a common set of signal lines.
Individual assignment of a signal to a specific signal line is configured through registers in the System Interface
Unit (SIU) and the Host Interface (HDI16). 1-5 describes the signals in this group.
Note: To boot from the host interface, the HDI16 must be enabled by pulling up the HPE signal line during
PORESET. The configuration word must then be loaded from the host. The configuration word must set the
Internal Space Port Size bit in the Bus Control Register (BCR[ISPS]) to change the system data bus width
from 64 bits to 32 bits and reassign the upper 32 bits to their HDI16 functions. Never set the Host Port
Enable (HEN) bit in the Host Port Control Register (HPCR) to enable the HDI16, unless the bus size is
first changed from 64 bits to 32 bits. Otherwise, unpredictable operation may occur.
MSC8101 Technical Data, Rev. 16
1-6
Freescale Semiconductor
System Bus, HDI16, and Interrupt Signals
Although there are eight interrupt request (IRQ) connections to the core processor, there are multiple external lines
that can connect to these internal signal lines. After reset, the default configuration includes two IRQ1 and two IRQ7
input lines. The designer must select one line for each required interrupt and reconfigure the other external signal
line or lines for alternate functions.
Table 1-5.
Signal
System Bus, HDI16, and Interrupt Signals
Data Flow
Description
A[0–31]
Input/Output
Address Bus
When the MSC8101 is in external master bus mode, these pins function as the address bus. The
MSC8101 drives the address of its internal bus masters and responds to addresses generated by
external bus masters. When the MSC8101 is in Internal Master Bus mode, these pins are used as
address lines connected to memory devices and are controlled by the MSC8101 memory controller.
TT[0–4]
Input/Output
Bus Transfer Type
The bus master drives these pins during the address tenure to specify the type of transaction.
TSIZ[0–3]
Input/Output
Transfer Size
The bus master drives these pins with a value indicating the number of bytes transferred in the
current transaction.
TBST
Input/Output
Bus Transfer Burst
The bus master asserts this pin to indicate that the current transaction is a burst transaction
(transfers four quad words).
IRQ1
Input
Interrupt Request 11
One of eight external lines that can request a service routine, via the internal interrupt controller,
from the SC140 core.
GBL
Input/Output
Global1
When a master within the chip initiates a bus transaction, it drives this pin. When an external master
initiates a bus transaction, it should drive this pin. Assertion of this pin indicates that the transfer is
global and it should be snooped by caches in the system.
Reserved
Output
The primary configuration is reserved.
BADDR29
Output
Burst Address 291
One of five outputs of the memory controller. These pins connect directly to memory devices
controlled by the MSC8101 memory controller.
IRQ2
Input
Interrupt Request 21
One of eight external lines that can request a service routine, via the internal interrupt controller,
from the SC140 core.
Reserved
Output
The primary configuration is reserved.
BADDR30
Output
Burst Address 301
One of five outputs of the memory controller. These pins connect directly to memory devices
controlled by the MSC8101 memory controller.
IRQ3
Input
Interrupt Request 31
One of eight external lines that can request a service routine, via the internal interrupt controller,
from the SC140 core.
Reserved
Output
The primary configuration is reserved.
BADDR31
Output
Burst Address 311
One of five outputs of the memory controller. These pins connect directly to memory devices
controlled by the MSC8101 memory controller.
IRQ5
Input
Interrupt Request 51
One of eight external lines that can request a service routine, via the internal interrupt controller,
from the SC140 core.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
1-7
Signals/Connections
Table 1-5.
Signal
BR
System Bus, HDI16, and Interrupt Signals (Continued)
Data Flow
Description
Request 2
Input/Output
Output
Bus
An output when an external arbiter is used. The MSC8101 asserts this pin to request ownership of
the bus.
Input
An input when an internal arbiter is used. An external master should assert this pin to request bus
ownership from the internal arbiter.
Input/Output
Output
Bus Grant2
An output when an internal arbiter is used. The MSC8101 asserts this pin to grant bus ownership to
an external bus master.
Input
An input when an external arbiter is used. The external arbiter should assert this pin to grant bus
ownership to the MSC8101.
Input/Output
Output
Address Bus Busy1
The MSC8101 asserts this pin for the duration of the address bus tenure. Following an address
acknowledge (AACK) signal, which terminates the address bus tenure, the MSC8101 deasserts
ABB for a fraction of a bus cycle and then stops driving this pin.
Input
The MSC8101 does not assume bus ownership while it this pin is asserted by an external bus
master.
IRQ2
Input
Interrupt Request 21
One of the eight external lines that can request a service routine, via the internal interrupt controller,
from the SC140 core.
TS
Input/Output
Bus Transfer Start
Signals the beginning of a new address bus tenure. The MSC8101 asserts this signal when one of
its internal bus masters (SC140 core or DMA controller) begins an address tenure. When the
MSC8101 senses this pin being asserted by an external bus master, it responds to the address bus
tenure as required (snoop if enabled, access internal MSC8101 resources, memory controller
support).
AACK
Input/Output
Address Acknowledge
A bus slave asserts this signal to indicate that it identified the address tenure. Assertion of this signal
terminates the address tenure.
ARTRY
Input
Address Retry
Assertion of this signal indicates that the bus transaction should be retried by the bus master. The
MSC8101 asserts this signal to enforce data coherency with its internal cache and to prevent
deadlock situations.
DBG
Input/Output
Output
Data Bus Grant2
An output when an internal arbiter is used. The MSC8101 asserts this pin as an output to grant data
bus ownership to an external bus master.
Input
An input when an external arbiter is used. The external arbiter should assert this pin as an input to
grant data bus ownership to the MSC8101.
Input/Output
Output
Data Bus Busy1
The MSC8101 asserts this pin as an output for the duration of the data bus tenure. Following a TA,
which terminates the data bus tenure, the MSC8101 deasserts DBB for a fraction of a bus cycle and
then stops driving this pin.
Input
The MSC8101 does not assume data bus ownership while DBB is asserted by an external bus
master.
IRQ3
Input
Interrupt Request 31
One of the eight external lines that can request a service routine, via the internal interrupt controller,
from the SC140 core.
D[0–31]
Input/Output
Data Bus Most Significant Word
In write transactions the bus master drives the valid data on this bus. In read transactions the slave
drives the valid data on this bus. In Host Port Disabled mode, these 32 bits are part of the 64-bit data
bus. In Host Port Enabled mode, these bits are used as the bus in 32-bit mode.
BG
ABB
DBB
MSC8101 Technical Data, Rev. 16
1-8
Freescale Semiconductor
System Bus, HDI16, and Interrupt Signals
Table 1-5.
Signal
Data Flow
System Bus, HDI16, and Interrupt Signals (Continued)
Description
D[32–47]
Input/Output
Data Bus Bits 32–47
In write transactions the bus master drives the valid data on this bus. In read transactions the slave
drives the valid data on this bus.
HD[0–15]
Input/Output
Host Data2
When the HDI16 interface is enabled, these signals are lines 0-15 of the bidirectional tri-state data
bus.
D[48–51]
Input/Output
Data Bus Bits 48–51
In write transactions the bus master drives the valid data on these pins. In read transactions the
slave drives the valid data on these pins.
HA[0–3]
Input
Host Address Line 0–33
When the HDI16 interface bus is enabled, these lines address internal host registers.
D52
Input/Output
Data Bus Bit 52
In write transactions the bus master drives the valid data on this pin. In read transactions the slave
drives the valid data on this pin.
HCS1
Input
Host Chip Select 3
When the HDI16 interface is enabled, this is one of the two chip-select pins. The HDI16 chip select
is a logical OR of HCS1 and HCS2.
D53
Input/Output
Data Bus Bit 53
In write transactions the bus master drives the valid data on this pin. In read transactions the slave
drives the valid data on this pin.
HRW
Input
Host Read Write Select3
When the HDI16 interface is enabled in Single Strobe mode, this is the read/write input (HRW).
HRD/HRD
Input
Host Read Strobe3
When the HDI16 is programmed to interface with a double data strobe host bus, this pin is the read
data strobe Schmitt trigger input (HRD/HRD). The polarity of the data strobe is programmable.
D54
Input/Output
Data Bus Bit 54
In write transactions the bus master drives the valid data on this pin. In read transactions the slave
drives the valid data on this pin.
HDS/HDS
Input
Host Data Strobe3
When the HDI16 is programmed to interface with a single data strobe host bus, this pin is the data
strobe Schmitt trigger input (HDS/HDS). The polarity of the data strobe is programmable.
HWR/HWR
Input
Host Write Data Strobe3
When the HDI16 is programmed to interface with a double data strobe host bus, this pin is the write
data strobe Schmitt trigger input (HWR/HWR). The polarity of the data strobe is programmable.
D55
Input/Output
Data Bus Bit 55
In write transactions the bus master drives the valid data on this pin. In read transactions the slave
drives the valid data on this pin.
HREQ/HREQ
Output
Host Request 3
When the HDI16 is programmed to interface with a single host request host bus, this pin is the host
request output (HREQ/HREQ). The polarity of the host request is programmable. The host request
may be programmed as a driven or open-drain output.
HTRQ/HTRQ
Output
Transmit Host Request3
When the HDI16 is programmed to interface with a double host request host bus, this pin is the
transmit host request output (HTRQ/HTRQ). The signal can be programmed as driven or open
drain. The polarity of the host request is programmable.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
1-9
Signals/Connections
Table 1-5.
Signal
System Bus, HDI16, and Interrupt Signals (Continued)
Data Flow
Description
D56
Input/Output
Data Bus Bit 56
In write transactions the bus master drives the valid data on this pin. In read transactions the slave
drives the valid data on this pin.
HACK/HACK
Output
Host Acknowledge3
When the HDI16 is programmed to interface with a single host request host bus, this pin is the host
acknowledge Schmitt trigger input (HACK). The polarity of the host acknowledge is programmable.
HRRQ/HRRQ
Output
Receive Host Request3
When the HDI16 is programmed to interface with a double host request host bus, this pin is the
receive host request output (HRRQ/HRRQ). The signal can be programmed as driven or open drain.
The polarity of the host request is programmable.
D57
Input/Output
Data Bus Bit 57
In write transactions the bus master drives the valid data on this pin. In read transactions the slave
drives the valid data on this pin.
HDSP
Input
Host Data Strobe Polarity3
When the HDI16 interface is enabled, this pin is the host data strobe polarity (HDSP).
D58
Input/Output
Data Bus Bit 58
In write transactions the bus master drives the valid data on this pin. In read transactions the slave
drives the valid data on this pin.
HDDS
Input
Host Dual Data Strobe3
When the HDI16 interface is enabled, this pin is the host dual data strobe (HDDS).
D59
Input/Output
Data Bus Bit 59
In write transactions the bus master drives the valid data on this pin. In read transactions the slave
drives the valid data on this pin.
H8BIT
Input
H8BIT3
When the HDI16 interface is enabled, this bit determines if the interface is in 8-bit or 16-bit mode.
D60
Input/Output
Data Bus Bit 60
In write transactions the bus master drives the valid data on this pin. In read transactions the slave
drives the valid data on this pin.
HCS2
Input
Host Chip Select 3
When the HDI16 interface is enabled, this is one of the two chip-select pins. The HDI16 chip select
is a logical OR of HCS1 and HCS2.
D[61–63]
Input/Output
Data Bus Bits 61–63
Used only in 60x-mode-only mode. In write transactions the bus master drives the valid data on this
bus. In read transactions the slave drives the valid data on this bus.
These dedicated signals are reserved when the HDI16 is enabled.3
Reserved
Reserved
Input
The primary configuration is reserved.
DP0
Input/Output
Data Parity 01
The agent that drives the data bus also drives the data parity signals. The value driven on the data
parity zero pin should give odd parity (odd number of ones) on the group of signals that includes
data parity 0 and D[0–7].
EXT_BR2
Input
External Bus Request 21,2
An external master asserts this pin to request bus ownership from the internal arbiter.
MSC8101 Technical Data, Rev. 16
1-10
Freescale Semiconductor
System Bus, HDI16, and Interrupt Signals
Table 1-5.
Signal
System Bus, HDI16, and Interrupt Signals (Continued)
Data Flow
Description
11
IRQ1
Input
Interrupt Request
One of eight external lines that can request a service routine, via the internal interrupt controller,
from the SC140 core.
DP1
Input/Output
Data Parity 11
The agent that drives the data bus also drives the data parity signals. The value driven on the data
parity one pin should give odd parity (odd number of ones) on the group of signals that includes data
parity 1 and D[8–15].
EXT_BG2
Output
External Bus Grant 21,2
The MSC8101 asserts this pin to grant bus ownership to an external bus master.
IRQ2
Input
Interrupt Request 21
One of eight external lines that can request a service routine, via the internal interrupt controller,
from the SC140 core.
DP2
Input/Output
Data Parity 21
The agent that drives the data bus also drives the data parity signals. The value driven on the data
parity two pin should give odd parity (odd number of ones) on the group of signals that includes data
parity 2 and D[16–23].
EXT_DBG2
Output
External Data Bus Grant 21,2
The MSC8101 asserts this pin to grant data bus ownership to an external bus master.
IRQ3
Input
Interrupt Request 31
One of eight external lines that can request a service routine, via the internal interrupt controller,
from the SC140 core.
DP3
Input/Output
Data Parity 31
The agent that drives the data bus also drives the data parity signals. The value driven on the data
parity three pin should give odd parity (odd number of ones) on the group of signals that includes
data parity 3 and D[24–31].
EXT_BR3
Input
External Bus Request 31,2
An external master asserts this pin to request bus ownership from the internal arbiter.
IRQ4
Input
Interrupt Request 41
One of eight external lines that can request a service routine, via the internal interrupt controller,
from the SC140 core.
DP4
Input/Output
Data Parity 41
The agent that drives the data bus also drives the data parity signals. The value driven on the data
parity four pin should give odd parity (odd number of ones) on the group of signals that includes data
parity 4 and D[32–39].
DREQ3
Input
DMA Request 31
An external peripheral uses this pin to request DMA service.
EXT_BG3
Output
External Bus Grant 31,2
The MSC8101 asserts this pin to grant bus ownership to an external bus master.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
1-11
Signals/Connections
Table 1-5.
Signal
System Bus, HDI16, and Interrupt Signals (Continued)
Data Flow
Description
51
IRQ5
Input
Interrupt Request
One of eight external lines that can request a service routine, via the internal interrupt controller,
from the SC140 core.
DP5
Input/Output
Data Parity 51
The agent that drives the data bus also drives the data parity signals. The value driven on the data
parity five pin should give odd parity (odd number of ones) on the group of signals that includes data
parity 5 and D[40–47].
DREQ4
Input
DMA Request 41
An external peripheral uses this pin to request DMA service.
EXT_DBG3
Output
External Data Bus Grant 31,2
The MSC8101 asserts this pin to grant data bus ownership to an external bus master.
IRQ6
Input
Interrupt Request 61
One of eight external lines that can request a service routine, via the internal interrupt controller,
from the SC140 core.
DP6
Input/Output
Data Parity 61
The agent that drives the data bus also drives the data parity signals. The value driven on the data
parity six pin should give odd parity (odd number of ones) on the group of signals that includes data
parity 6 and D[48–55].
DACK3
Output
DMA Acknowledge 31
The DMA controller drives this output to acknowledge the DMA transaction on the bus.
IRQ7
Input
Interrupt Request 71
One of eight external lines that can request a service routine, via the internal interrupt controller,
from the SC140 core.
DP7
Input/Output
Data Parity 71
The master or slave that drives the data bus also drives the data parity signals. The value driven on
the data parity seven pin should give odd parity (odd number of ones) on the group of signals that
includes data parity 7 and D[56–63].
DACK4
Output
DMA Acknowledge1
The DMA controller drives this output to acknowledge the DMA transaction on the bus.
TA
Input/Output
Transfer Acknowledge
Indicates that a data beat is valid on the data bus. For single beat transfers, assertion of TA
indicates the termination of the transfer. For burst transfers, TA is asserted four times to indicate the
transfer of four data beats with the last assertion indicating the termination of the burst transfer.
TEA
Input/Output
Transfer Error Acknowledge
Indicates a bus error. masters within the MSC8101 monitor the state of this pin. The MSC8101
internal bus monitor can assert this pin if it identifies a bus transfer that is hung.
NMI
Input
Non-Maskable Interrupt
When an external device asserts this line, the MSC8101 NMI input is asserted.
NMI_OUT
Output
Non-Maskable Interrupt
Driven from the MSC8101 internal interrupt controller. Assertion of this output indicates that a
non-maskable interrupt, pending in the MSC8101 internal interrupt controller, is waiting to be
handled by an external host.
PSDVAL
Input/Output
Data Valid
Indicates that a data beat is valid on the data bus. The difference between the TA pin and PSDVAL
is that the TA pin is asserted to indicate data transfer terminations while the PSDVAL signal is
asserted with each data beat movement. Thus, when TA is asserted, PSDVAL is asserted, but when
PSDVAL is asserted, TA is not necessarily asserted. For example when the SDMA initiates a double
word (2x64 bits) transfer to a memory device that has a 32-bit port size, PSDVAL is asserted three
times without TA, and finally both pins are asserted to terminate the transfer.
MSC8101 Technical Data, Rev. 16
1-12
Freescale Semiconductor
Memory Controller Signals
Table 1-5.
Signal
System Bus, HDI16, and Interrupt Signals (Continued)
Data Flow
Description
71
IRQ7
Input
Interrupt Request
One of eight external lines that can request a service routine, via the internal interrupt controller,
from the SC140 core.
INT_OUT
Output
Interrupt Output1
Driven from the MSC8101 internal interrupt controller. Assertion of this output indicates that an
unmasked interrupt is pending in the MSC8101 internal interrupt controller.
Notes:
1.
2.
3.
See the SIU chapter in the MSC8101 Reference Manual for details on how to configure these pins.
When used as the bus control arbiter for the system bus, the MSC8101 can support up to three external bus masters. Each
master uses its own set of Bus Request, Bus Grant, and Data Bus Grant signals (BR/BG/DBG,
EXT_BR2/EXT_BG2/EXT_DBG2, and EXT_BR3/EXT_BG3/EXT_DBG3). Each of these signal sets must be configured to
indicate whether the external master is or is not a MSC8101 master device. See the Bus Configuration Register (BCR)
description in the SIU chapter in the MSC8101 Reference Manual for details on how to configure these pins. The second and
third set of pins is defined by EXT_xxx to indicate that they can only be used with external master devices. The first set of pins
(BR/BG/DBG) have a dual function. When the MSC8101 is not the bus arbiter, these signals (BR/BG/DBG) are used by the
MSC8101 to obtain master control of the bus.
See the host interface (HDI16) chapter in the MSC8101 Reference Manual for details on how to configure these pins.
1.5 Memory Controller Signals
Refer to the memory controller chapter in the MSC8101 Reference Manual (MSC8101RM/D) for detailed
information about configuring these signals.
Table 1-6.
Signal
Data Flow
Memory Controller Signals
Description
CS[0–7]
Output
Chip Select
Enable specific memory devices or peripherals connected to MSC8101 buses.
BCTL1
Output
Buffer Control 1
Controls buffers on the data bus. Usually used with BCTL0. The exact function of this pin is defined
by the value of SIUMCR[BCTLC]. See the System Interface Unit (SIU) chapter in the MSC8101
Reference Manual for details.
BADDR[27–28]
Output
Burst Address 27–28
Two of five outputs of the memory controller. These pins connect directly to memory devices
controlled by the MSC8101 memory controller.
ALE
Output
Address Latch Enable
Controls the external address latch used in external master bus configuration.
BCTL0
Output
Buffer Control 0
Controls buffers on the data bus. The exact function of this pin is defined by the value of
SIUMCR[BCTLC]. See the System Interface Unit (SIU) chapter in the MSC8101 Reference Manual
for details.
PWE[0–7]
Output
Bus Write Enable
Outputs of the bus General-Purpose Chip-select Machine (GPCM). These pins select byte lanes for
write operations.
PSDDQM[0–7]
Output
Bus SDRAM DQM
Outputs of the SDRAM control machine. These pins select specific byte lanes of SDRAM devices.
PBS[0–7]
Output
Bus UPM Byte Select
Outputs of the User-Programmable Machine (UPM) in the memory controller. These pins select
specific byte lanes during memory operations. The timing of these pins is programmed in the UPM.
The actual driven value depends on the address and size of the transaction and the port size of the
accessed device.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
1-13
Signals/Connections
Table 1-6.
Signal
Memory Controller Signals (Continued)
Data Flow
Description
PSDA10
Output
Bus SDRAM A10
Output from the bus SDRAM controller. This pin is part of the address when a row address is driven.
It is part of the command when a column address is driven.
PGPL0
Output
Bus UPM General-Purpose Line 0
One of six general-purpose output lines of the UPM. The values and timing of this pin are
programmed in the UPM.
PSDWE
Output
Bus SDRAM Write Enable
Output from the bus SDRAM controller. This pin should connect to the SDRAM WE input signal.
PGPL1
Output
Bus UPM General-Purpose Line 1
One of six general-purpose output lines from the UPM. The values and timing of this pin are
programmed in the UPM.
POE
Output
Bus Output Enable
Output of the bus GPCM. Controls the output buffer of memory devices during read operations.
PSDRAS
Output
Bus SDRAM RAS
Output from the bus SDRAM controller. This pin should connect to the SDRAM Row Address Strobe
(RAS) input signal.
PGPL2
Output
Bus UPM General-Purpose Line 2
One of six general-purpose output lines from the UPM. The values and timing of this pin are
programmed in the UPM.
PSDCAS
Output
Bus SDRAM CAS
Output from the bus SDRAM controller. This pin should connect to the SDRAM Column Address
Strobe (CAS) input signal.
PGPL3
Output
Bus UPM General-Purpose Line 3
One of six general-purpose output lines from the UPM. The values and timing of this pin are
programmed in the UPM.
PGTA
Input
GPCM TA
Terminates transactions during GPCM operation. Requires an external pull up resistor for proper
operation.
PUPMWAIT
Input
Bus UPM Wait
Input to the UPM. An external device can hold this pin high to force the UPM to wait until the device
is ready for the operation to continue.
PPBS
Output
Bus Parity Byte Select
In systems that store data parity in a separate chip, this output is the byte-select for that chip.
PGPL4
Output
Bus UPM General-Purpose Line 4
One of six general-purpose output lines from the UPM. The values and timing of this pin are
programmed in the UPM.
PSDAMUX
Output
Bus SDRAM Address Multiplexer
Controls the SDRAM address multiplexer when the MSC8101 is in External Master mode.
PGPL5
Output
Bus UPM General-Purpose Line 5
One of six general-purpose output lines from the UPM. The values and timing of this pin are
programmed in the UPM.
MSC8101 Technical Data, Rev. 16
1-14
Freescale Semiconductor
CPM Ports
1.6 CPM Ports
The MSC8101 CPM supports the subset of MPC8260 signals as described below.
• The MSC8101 CPM includes the following set of communication controllers:
• Two full-duplex fast serial communications controllers (FCCs) that support:
— Asynchronous transfer mode (ATM) through a UTOPIA 8 interface (FCC1 only)—The MSC8101 can
operate as one of the following:
UTOPIA slave device
UTOPIA multi-PHY master device using direct polling for up to 4 PHY devices
° UTOPIA multi-PHY master device using multiplex polling that can address up to 31 PHY devices at addresses 0–30
(address 31 is reserved as a null port).
°
°
— IEEE 802.3/Fast Ethernet through a Media-Independent Interface (MII)
— High-level data link control (HDLC) Protocol:
°
°
Serial mode—Transfers data one bit at a time
Nibble mode—Transfers data four bits at a time
— Transparent mode serial operation
• One FCC that operates with the TSA only
• Two multi-channel controllers (MCCs) that together can handle up to 256 HDLC/transparent channels at 64
Kbps each, multiplexed on up to four TDM interfaces
• Two full-duplex serial communications controllers (SCCs) that support the following protocols:
— IEEE 802.3/fast Ethernet through a media-independent interface (MII)
— HDLC Protocol:
Serial mode—Transfers data one bit at a time
° Nibble mode—Transfers data four bits at a time
°
—
—
—
—
—
—
Synchronous data link control (SDLC)
LocalTalk (HDLC-based local area network protocol)
Universal asynchronous receiver/transmitter (UART)
Synchronous UART (1x clock mode)
Binary synchronous (BISYNC) communication
Transparent mode serial operation
• Two additional SCCs that operate with the TSA only
• Two full-duplex serial management controllers (SMCs) that support the following protocols:
— General circuit interface (GCI)/integrated services digital network (ISDN) monitor and C/I channels (TSA
only)
— UART
— Transparent mode serial operation
• Serial peripheral interface (SPI) support for master or slave operation
• Inter-integrated circuit (I2C) bus controller
• Time-slot assigner (TSA) that supports multiplexing from any of the SCCs, FCCs, SMCs, and two MCCs onto
four time-division multiplexed (TDM) interfaces. The TSA uses two serial interfaces (SI1 and SI2). SI1 uses
TDMA1 which supports both serial and nibble mode. SI2 does not support nibble mode and includes TDMB2,
TDMC2, and TDMD2, which operate only in serial mode.
The individual sets of externals signals associated with a specific protocol and data transfer mode are multiplexed
across any or all of the ports, as shown in Figure 1-2. The following sections describe the signals supported by
Ports A–D.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
1-15
Signals/Connections
1.6.1
Port A Signals
Table 1-7.
Port A Signals
Name
GeneralPurpose I/O
PA31
PA30
Output
FCC1: TXENB
UTOPIA slave
Input
FCC1: UTOPIA Slave Transmit Enable
Asserted by an external UTOPIA master PHY when there is valid
transmit cell data (TXD[0–7]).
FCC1: COL
MII
Input
FCC1: Media Independent Interface Collision Detect
Asserted by an external fast Ethernet PHY when collision is detected.
Output
FCC1: UTOPIA Slave Transmit Cell Available
Asserted by the MSC8101 (UTOPIA slave PHY) when the MSC8101
can accept one complete ATM cell.
FCC1: TXCLAV
UTOPIA slave
FCC1: UTOPIA Master Transmit Enable
Asserted by the MSC8101 (UTOPIA master PHY) when there is valid
transmit cell data (TXD[0–7]).
FCC1: TXCLAV
UTOPIA master, or
Input
FCC1: UTOPIA Master Transmit Cell Available
Asserted by an external UTOPIA slave PHY to indicate that it can accept
one complete ATM cell.
FCC1: TXCLAV0
UTOPIA master, Multi-PHY, direct
polling
Input
FCC1: UTOPIA Master Transmit Cell Available Multi-PHY Direct
Polling
Asserted by an external UTOPIA slave PHY using direct polling to
indicate that it can accept one complete ATM cell.
FCC1: CRS
MII
PA28
Description
FCC1: TXENB
UTOPIA master
FCC1: RTS
HDLC, Serial and Nibble
PA29
Dedicated
I/O Data
Direction
Peripheral Controller:
Dedicated Signal
Protocol
Output
Input
FCC1: Request To Send
In the standard modem interface signals supported by FCC1 (RTS,
CTS, and CD). RTS is asynchronous with the data. RTS is typically used
in conjunction with CD. The MSC8101 FCC1 transmitter requests the
receiver to send data by asserting RTS low. The request is accepted
when CTS is returned low.
FCC1: Media Independent Interface Carrier Sense
Asserted by an external fast Ethernet PHY to indicate activity on the
cable.
FCC1: TXSOC
UTOPIA master
Output
FCC1: UTOPIA Transmit Start of Cell
Asserted by the MSC8101 (UTOPIA master PHY) when TXD[0–7]
contains the first valid byte of the cell.
FCC1: TX_ER
MII
Output
FCC1: Media Independent Interface Transmit Error
Asserted by the MSC8101 to force propagation of transmit errors.
FCC1: RXENB
UTOPIA master
Output
FCC1: UTOPIA Master Receive Enable
Asserted by the MSC8101 (UTOPIA master PHY) to indicate that
RXD[0–7] and RXSOC are to be sampled at the end of the next cycle.
RXD[0–7] and RXSOC are enabled only in cycles following those with
RXENB asserted.
FCC1: RXENB
UTOPIA slave
Input
FCC1: TX_EN
MII
Output
FCC1: UTOPIA Master Receive Enable
Asserted by an external PHY to indicate that RXD[0–7] and RXSOC is to
be sampled at the end of the next cycle. RXD[0–7] and RXSOC are
enabled only in cycles following those with RXENB asserted.
FCC1: Media Independent Interface Transmit Enable
Asserted by the MSC8101 when transmitting data.
MSC8101 Technical Data, Rev. 16
1-16
Freescale Semiconductor
CPM Ports
Table 1-7.
Port A Signals (Continued)
Name
GeneralPurpose I/O
PA27
PA26
PA25
PA24
PA23
Dedicated
I/O Data
Direction
Peripheral Controller:
Dedicated Signal
Protocol
FCC1: RXSOC
UTOPIA slave
Output
FCC1: RX_DV
MII
Input
FCC1: RXCLAV
UTOPIA slave
Output
Description
FCC1: UTOPIA Receive Start of Cell
Asserted by the MSC8101 (UTOPIA slave) for an external PHY when
RXD[0–7] contains the first valid byte of the cell.
FCC1: Media Independent Interface Receive Data Valid
Asserted by an external fast Ethernet PHY to indicate that valid data is
being sent. The presence of carrier sense but not RX_DV indicates
reception of broken packet headers, probably due to bad wiring or a bad
circuit.
FCC1: UTOPIA Slave Receive Cell Available
Asserted by the MSC8101 (UTOPIA slave PHY) when one complete
ATM cell is available for transfer.
FCC1: RXCLAV
UTOPIA master, or
Input
FCC1: UTOPIA Master Receive Cell Available
Asserted by an external PHY when one complete ATM cell is available
for transfer.
RXCLAV0
UTOPIA master, Multi-PHY, direct
polling
Input
FCC1: UTOPIA Master Receive Cell Available 0 Direct Polling
Asserted by an external PHY when one complete ATM cell is available
for transfer.
FCC1: RX_ER
MII
Input
FCC1: Media Independent Interface Receive Error
Asserted by an external fast Ethernet PHY to indicate a receive error,
which often indicates bad wiring.
FCC1: TXD0
UTOPIA
Output
FCC1: UTOPIA Transmit Data Bit 0
The MSC8101 outputs ATM cell octets (UTOPIA interface data) on
TXD[0–7]. TXD0 is the least significant bit. When no ATM data is
available, idle cells are inserted. A cell is 53 bytes.
SDMA: MSNUM0
Output
Module Serial Number Bit 0
The MSNUM has 6 bits that identify devices using the serial DMA
(SDMA) modules. MSNUM[0–4] is the sub-block code of the current
peripheral controller using SDMA. MSNUM5 indicates the section,
transmit (0) or receive (1), that is active during the transfer. The
information is recorded in the SDMA transfer error registers.
FCC1: TXD1
UTOPIA
Output
FCC1: UTOPIA Transmit Data Bit 1
The MSC8101 outputs ATM cell octets (UTOPIA interface data) on
TXD[0–7]. This is bit 1 of the transmit data. TXD7 is the most significant
bit. When no ATM data is available, idle cells are inserted. A cell is 53
bytes.
SDMA: MSNUM1
Output
Module Serial Number Bit 1
The MSNUM has 6 bits that identify devices using the serial DMA
(SDMA) modules. MSNUM[0–4] is the sub-block code of the current
peripheral controller using SDMA. MSNUM5 indicates the section,
transmit (0) or receive (1), that is active during the transfer. The
information is recorded in the SDMA transfer error registers.
FCC1: TXD2
UTOPIA
Output
FCC1: UTOPIA Transmit Data Bit 2
The MSC8101 outputs ATM cell octets (UTOPIA interface data) on
TXD[0–7]. This is bit 2 of the transmit data. TXD7 is the most significant
bit. When no ATM data is available, idle cells are inserted. A cell is 53
bytes.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
1-17
Signals/Connections
Table 1-7.
Port A Signals (Continued)
Name
GeneralPurpose I/O
Peripheral Controller:
Dedicated Signal
Protocol
Dedicated
I/O Data
Direction
Description
PA22
FCC1: TXD3
UTOPIA
Output
FCC1: UTOPIA Transmit Data Bit 3
The MSC8101 outputs ATM cell octets (UTOPIA interface data) on
TXD[0–7]. This is bit 3 of the transmit data. TXD7 is the most significant
bit. When no ATM data is available, idle cells are inserted. A cell is 53
bytes.
PA21
FCC1: TXD4
UTOPIA
Output
FCC1: UTOPIA Transmit Data Bit 4
The MSC8101 outputs ATM cell octets (UTOPIA interface data) on
TXD[0–7]. This is bit 4 of the transmit data. TXD7 is the most significant
bit. When no ATM data is available, idle cells are inserted. A cell is 53
bytes.
FCC1: TXD3
MII and HDLC nibble
Output
FCC1: MII and HDLC Nibble Transmit Data Bit 3
TXD[3–0] supports MII and HDLC nibble modes in FCC1. TXD3 is the
most significant bit.
FCC1: TXD5
UTOPIA
Output
FCC1: UTOPIA Transmit Data Bit 5
The MSC8101 outputs ATM cell octets (UTOPIA interface data) on
TXD[0–7]. This is bit 5 of the transmit data. TXD7 is the most significant
bit. When no ATM data is available, idle cells are inserted. A cell is 53
bytes.
FCC1: TXD2
MII and HDLC nibble
Output
FCC1: MII and HDLC Nibble Transmit Data Bit 2
TXD[3–0] is supported by MII and HDLC nibble modes in FCC1. This is
bit 2 of the transmit data. TXD3 is the most significant bit.
FCC1: TXD6
UTOPIA
Output
FCC1: UTOPIA Transmit Data Bit 6
The MSC8101MSC8101 outputs ATM cell octets (UTOPIA interface
data) on TXD[0–7]. This is bit 6 of the transmit data. TXD7 is the most
significant bit. When no ATM data is available, idle cells are inserted. A
cell is 53 bytes.
FCC1: TXD1
MII and HDLC nibble
Output
FCC1: MII and HDLC Nibble Transmit Data Bit 1
TXD[3–0] is supported by MII and HDLC transparent nibble modes in
FCC1. This is bit 1 of the transmit data. TXD3 is the most significant bit.
FCC1: TXD7
UTOPIA
Output
FCC1: UTOPIA Transmit Data Bit 7.
The MSC8101 outputs ATM cell octets (UTOPIA interface data) on
TXD[0–7]. TXD7 is the most significant bit. When no ATM data is
available, idle cells are inserted. A cell is 53 bytes.
FCC1: TXD0
MII and HDLC nibble
Output
FCC1: MII and HDLC Nibble Transmit Data Bit 0
TXD[3–0] is supported by MII and HDLC nibble modes in FCC1. TXD0
is the least significant bit.
FCC1: TXD
HDLC serial and transparent
Output
FCC1: HDLC Serial and Transparent Transmit Data Bit
This is the single transmit data bit in supported by HDLC serial and
transparent modes.
PA20
PA19
PA18
MSC8101 Technical Data, Rev. 16
1-18
Freescale Semiconductor
CPM Ports
Table 1-7.
Port A Signals (Continued)
Name
GeneralPurpose I/O
PA17
PA16
PA15
PA14
PA13
Peripheral Controller:
Dedicated Signal
Protocol
Dedicated
I/O Data
Direction
Description
FCC1: RXD7
UTOPIA
Input
FCC1: UTOPIA Receive Data Bit 7.
The MSC8101 inputs ATM cell octets (UTOPIA interface data) on
RXD[0–7]. RXD7 is the most significant bit. When no ATM data is
available, idle cells are inserted. A cell is 53 bytes. To support Multi-PHY
configurations, RXD[0–7] is tri-stated, enabled only when RXENB is
asserted.
FCC1: RXD0
MII and HDLC nibble
Input
FCC1: MII and HDLC Nibble Receive Data Bit 0
RXD[3–0] is supported by MII and HDLC nibble mode in FCC1. RXD0 is
the least significant bit.
FCC1: RXD
HDLC serial and transparent
Input
FCC1: HDLC Serial and Transparent Receive Data Bit
This is the single receive data bit supported by HDLC and transparent
modes.
FCC1: RXD6
UTOPIA
Input
FCC1: UTOPIA Receive Data Bit 6.
The MSC8101 inputs ATM cell octets (UTOPIA interface data) on
RXD[0–7]. This is bit 6 of the receive data. RXD7 is the most significant
bit. When no ATM data is available, idle cells are inserted. A cell is 53
bytes. To support Multi-PHY configurations, RXD[0–7] is tri-stated,
enabled only when RXENB is asserted.
FCC1: RXD1
MII and HDLC nibble
Input
FCC1: MII and HDLC Nibble Receive Data Bit 1
This is bit 1 of the receive nibble data. RXD3 is the most significant bit.
FCC1: RXD5
UTOPIA
Input
FCC1: UTOPIA Receive Data Bit 5
The MSC8101 inputs ATM cell octets (UTOPIA interface data) on
RXD[0–7]. This is bit 5 of the receive data. RXD7 is the most significant
bit. When no ATM data is available, idle cells are inserted. A cell is 53
bytes. To support Multi-PHY configurations, RXD[0–7] is tri-stated,
enabled only when RXENB is asserted.
RXD2
MII and HDLC nibble
Input
FCC1: MII and HDLC Nibble Receive Data Bit 2
This is bit 2 of the receive nibble data. RXD3 is the most significant bit.
FCC1: RXD4
UTOPIA
Input
FCC1: UTOPIA Receive Data Bit 4.
The MSC8101 inputs ATM cell octets (UTOPIA interface data) on
RXD[0–7]. RXD7 is the most significant bit. RXD0 is the least significant
bit. When no ATM data is available, idle cells are inserted. A cell is 53
bytes. To support Multi-PHY configurations, RXD[0–7] is tri-stated,
enabled only when RXENB is asserted.
FCC1: RXD3
MII and HDLC nibble
Input
FCC1: MII and HDLC Nibble Receive Data Bit 3
RXD3 is the most significant bit of the receive nibble bit.
FCC1: RXD3
UTOPIA
Input
FCC1: UTOPIA Receive Data Bit 3
The MSC8101 inputs ATM cell octets (UTOPIA interface data) on
RXD[0–7]. RXD7 is the most significant bit. RXD0 is the least significant
bit. A cell is 53 bytes. To support Multi-PHY configurations, RXD[0–7] is
tri-stated, enabled only when RXENB is asserted.
SDMA: MSNUM2
Output
Module Serial Number Bit 2
The MSNUM has 6 bits that identify devices using the serial DMA
(SDMA) modules. MSNUM[0–4] is the sub-block code of the current
peripheral controller using SDMA. MSNUM5 indicates the section,
transmit (0) or receive (1), that is active during the transfer. The
information is recorded in the SDMA transfer error registers.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
1-19
Signals/Connections
Table 1-7.
Port A Signals (Continued)
Name
GeneralPurpose I/O
PA12
Peripheral Controller:
Dedicated Signal
Protocol
FCC1: RXD2
UTOPIA
SDMA: MSNUM3
PA11
FCC1: RXD1
UTOPIA
SDMA: MSNUM4
PA10
PA9
PA8
FCC1: RXD0
UTOPIA
Dedicated
I/O Data
Direction
Input
Output
Input
Output
Input
Description
FCC1: UTOPIA Receive Data Bit 2
The MSC8101 inputs ATM cell octets (UTOPIA interface data) on
RXD[0–7]. This is bit 2 of the receive data. RXD7 is the most significant
bit. A cell is 53 bytes. To support Multi-PHY configurations, RXD[0–7] is
tri-stated, enabled only when RXENB is asserted.
Module Serial Number Bit 3
The MSNUM has 6 bits that identify devices using the serial DMA
(SDMA) modules. MSNUM[0–4] is the sub-block code of the current
peripheral controller using SDMA. MSNUM5 indicates the section,
transmit (0) or receive (1), that is active during the transfer. The
information is recorded in the SDMA transfer error registers.
FCC1: UTOPIA RX Receive Data Bit 1
The MSC8101 inputs ATM cell octets (UTOPIA interface data) on
RXD[0–7]. This is bit 1 of the receive data. RXD7 is the most significant
bit. A cell is 53 bytes. To support Multi-PHY configurations, RXD[0–7] is
tri-stated, enabled only when RXENB is asserted.
Module Serial Number Bit 4
The MSNUM has 6 bits that identify devices using the serial DMA
(SDMA) modules. MSNUM[0–4] is the sub-block code of the current
peripheral controller using SDMA. MSNUM5 indicates the section,
transmit (0) or receive (1), that is active during the transfer. The
information is recorded in the SDMA transfer error registers.
FCC1: UTOPIA RX Receive Data Bit 0
The MSC8101 inputs ATM cell octets (UTOPIA interface data) on
RXD[0–7]. RXD0 is the least significant bit of the receive data. A cell is
53 bytes. To support Multi-PHY configurations, RXD[0–7] is tri-stated,
enabled only when RXENB is asserted.
SDMA: MSNUM5
Output
Module Serial Number Bit 5
The MSNUM has 6 bits that identify devices using the serial DMA
(SDMA) modules. MSNUM[0–4] is the sub-block code of the current
peripheral controller using SDMA. MSNUM5 indicates the section,
transmit (0) or receive (1), that is active during the transfer. The
information is recorded in the SDMA transfer error registers.
SMC2: SMTXD
Output
SMC2: Serial Management Transmit Data
The SMC interface consists of SMTXD, SMRXD, SMSYN, and a clock.
Not all signals are used for all applications. SMCs are full-duplex ports
that supports three protocols or modes: UART, transparent, or generalcircuit interface (GCI). See also PC15.
SI1 TDMA1: L1TXD0
TDM nibble
Output
Time-Division Multiplexing A1: Layer 1 Transmit Data Bit 0
L1TXD0 is the least significant bit of the TDM nibble data.
SMC2: SMRXD
Input
SMC2: Serial Management Receive Data
The SMC interface consists of SMTXD, SMRXD, SMSYN, and a clock.
Not all signals are used for all applications. SMCs are full-duplex ports
that supports three protocols or modes: UART, transparent, or generalcircuit interface (GCI).
SI1 TDMA1: L1RXD0
TDM nibble
Input
Time-Division Multiplexing A1: Layer 1 Nibble Receive Data Bit 0
L1RXD0 is the least significant bit received in nibble mode.
SI1 TDMA1: L1RXD
TDM serial
Input
Time-Division Multiplexing A1: Layer 1 Serial Receive Data
TDMA1 receives serial data from L1RXD.
MSC8101 Technical Data, Rev. 16
1-20
Freescale Semiconductor
CPM Ports
Table 1-7.
Port A Signals (Continued)
Name
GeneralPurpose I/O
PA7
PA6
1.6.2
Peripheral Controller:
Dedicated Signal
Protocol
Dedicated
I/O Data
Direction
Description
SMC2: SMSYN
Input
SMC2: Serial Management Synchronization
The SMC interface consists of SMTXD, SMRXD, SMSYN, and a clock.
Not all signals are used for all applications. SMCs are full-duplex ports
that supports three protocols or modes: UART, transparent, or generalcircuit interface (GCI).
SI1 TDMA1: L1TSYNC
TDM nibble and TDM serial
Input
Time-Division Multiplexing A1: Layer 1 Transmit Synchronization
The synchronizing signal for the transmit channel. See the Serial
Interface with time-slot assigner chapter in the MSC8101 Reference
Manual.
SI1 TDMA1: L1RSYNC
TDM nibble and TDM serial
Input
Time-Division Multiplexing A1: Layer 1 Receive Synchronization.
The synchronizing signal for the receive channel.
Port B Signals
Table 1-8.
Port B Signals
Name
GeneralPurpose I/O
PB31
Peripheral Controller:
Dedicated I/O
Protocol
FCC2: TX_ER
MII
SCC2: RXD
PB30
PB29
Dedicated
I/O Data
Direction
Output
Input
Description
FCC2: Media Independent Interface Transmit Error
Asserted by the MSC8101 to force propagation of transmit errors.
SCC2: Receive Data
SCC2 receives serial data from RXD.
SI2 TDMB2: L1TXD
TDM serial
Output
Time-Division Multiplexing B2: Layer 1 Transmit Data
TDMB2 transmits serial data out of L1TXD.
SCC2: TXD
Output
SCC2: Transmit Data.
SCC2 transmits serial data out of TXD.
FCC2: RX_DV
MII
Input
FCC2: Media Independent Interface Receive Data Valid
Asserted by an external fast Ethernet PHY to indicate that valid data is
being sent. The presence of carrier sense, but not RX_DV, indicates
reception of broken packet headers, probably due to bad wiring or a bad
circuit.
SI2 TDMB2: L1RXD
TDM serial
Input
Time-Division Multiplexing B2: Layer 1 Receive Data
TDMB2 receives serial data from L1RXD.
Output
FCC2: Media Independent Interface Transmit Enable
Asserted by the MSC8101 when transmitting data.
FCC2: TX_EN
MII
SI2 TDMB2: L1RSYNC
TDM serial
Input
Time-Division Multiplexing B2: Layer 1 Receive Synchronization
The synchronizing signal for the receive channel.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
1-21
Signals/Connections
Table 1-8.
Port B Signals (Continued)
Name
GeneralPurpose I/O
PB28
Peripheral Controller:
Dedicated I/O
Protocol
FCC2: RTS
HDLC serial, HDLC nibble, and
transparent
FCC2: RX_ER
MII
SCC2: RTS, TENA
PB27
PB25
Input
FCC2: Request to Send
One of the standard modem interface signals supported by FCC2 (RTS,
CTS, and CD). RTS is asynchronous with the data. RTS is typically used
in conjunction with CD. The MSC8101 FCC2 transmitter requests the
receiver to send data by asserting RTS low. The request is accepted
when CTS is returned low.
FCC2: Media Independent Interface Receive Error
Asserted by an external fast Ethernet PHY to indicate a receive error,
which often indicates bad wiring.
SCC2: Request to Send, Transmit Enable
Typically used in conjunction with CD supported by SCC2. The
MSC8101 SCC2 transmitter requests the receiver to send data by
asserting RTS low. The request is accepted when CTS is returned low.
TENA is the signal used in Ethernet mode.
SI2 TDMB2: L1TSYNC
TDM serial
Input
Time-Division Multiplexing B2: Layer 1 Transmit Synchronization
The synchronizing signal for the transmit channel. See the serial
interface with time-slot assigner chapter in the MSC8101 Reference
Manual.
FCC2: COL
MII
Input
FCC2: Media Independent Interface Collision Detect
Asserted by an external fast Ethernet PHY when a collision is detected.
Output
Time-Division Multiplexing C2: Layer 1 Transmit Data
TDMC2 transmits serial data out of L1TXD.
FCC2: CRS
MII
Input
FCC2: Media Independent Interface Carrier Sense Input
Asserted by an external fast Ethernet PHY to indicate activity on the
cable.
SI2 TDMC2: L1RXD
TDM serial
Input
Time-Division Multiplexing C2: Layer 1 Receive Data
TDMC2 receives serial data from L1RXD.
FCC2: TXD3
MII and HDLC nibble
Output
SI1 TDMA1: L1TXD3
TDM nibble
Output
SI2 TDMC2: L1TSYNC
TDM serial
PB24
Output
Description
Output
SI2 TDMC2: L1TXD
TDM serial
PB26
Dedicated
I/O Data
Direction
Input
FCC2: MII and HDLC Nibble Transmit Data Bit 3
TXD3 is bit 3 and the most significant bit of the transmit data nibble.
Time-Division Multiplexing A1: Nibble Layer 1 Transmit Data Bit 3
L1TXD3 is bit 3 and the most significant bit of the transmit data nibble.
Time-Division Multiplexing C2: Layer 1 Transmit Synchronization
The synchronizing signal for the transmit channel. See the Serial
Interface with Time-Slot Assigner chapter in the MSC8101 Reference
Manual.
FCC2: TXD2
MII and HDLC nibble
Output
SI1 TDMA1: L1RXD3
nibble
Input
Time-Division Multiplexing A1: Nibble Layer 1 Receive Data Bit 3
L1RXD3 is bit 3 and the most significant bit of the receive data nibble.
SI2 TDMC2: L1RSYNC
serial
Input
Time-Division Multiplexing C2: Layer 1 Receive Synchronization
The synchronizing signal for the receive channel.
FCC2: MII and HDLC Nibble: Transmit Data Bit 2
TXD2 is bit 2 of the transmit data nibble.
MSC8101 Technical Data, Rev. 16
1-22
Freescale Semiconductor
CPM Ports
Table 1-8.
Port B Signals (Continued)
Name
GeneralPurpose I/O
PB23
PB22
PB21
Peripheral Controller:
Dedicated I/O
Protocol
FCC2: TXD1
MII and HDLC nibble
Output
SI1 TDMA1: L1RXD2
TDM nibble
Input
PB19
Description
FCC2: MII and HDLC Nibble: Transmit Data Bit 1
TXD1 is bit 1 of the transmit data nibble.
Time-Division Multiplexing A1: Nibble Layer 1 Receive Data Bit 2
L1RXD2 is bit 2 of the receive data nibble.
SI2 TDMD2: L1TXD
TDM serial
Output
Time-Division Multiplexing D2: Layer 1 Transmit Data
TDMA1 transmits serial data out of L1TXD.
FCC2: TXD0
MII and HDLC nibble
Output
FCC2: MII and HDLC Nibble Transmit Data Bit 0
TXD0 is bit 0 and the least significant bit of the transmit data nibble.
FCC2: TXD
HDLC serial and transparent
Output
FCC2: HDLC Serial and Transparent Transmit Data
Serial data is transmitted via TXD.
SI1 TDMA1: L1RXD1
TDM nibble
Input
Time-Division Multiplexing A1: Nibble Layer 1 Receive Data Bit 1
L1RXD1 is bit 1 of the receive data nibble.
SI2 TDMD2: L1RXD
TDM serial
Input
Time-Division Multiplexing D2: Layer 1 Receive Data
Serial data is received via L1RXD.
FCC2: RXD0
MII and HDLC nibble
Input
FCC2: MII and HDLC Nibble Receive Data Bit 0
RXD0 is bit 0 and the least significant bit of the receive data nibble.
FCC2: RXD
HDLC serial and transparent
Input
FCC2: HDLC Serial and Transparent Receive Data
Serial data is received via RXD.
SI1 TDMA1: L1TXD2
TDM nibble
PB20
Dedicated
I/O Data
Direction
Output
Time-Division Multiplexing A1: Nibble Layer 1 Transmit Data Bit 2
L1TXD2 is bit 2 of the transmit data nibble.
SI2 TDMD2: L1TSYNC
TDM serial
Input
Time-Division Multiplexing D2: Layer 1 Transmit Synchronize Data
The synchronizing signal for the transmit channel. See the Serial
Interface with Time-Slot Assigner chapter in the MSC8101 Reference
Manual.
FCC2: RXD1
MII and HDLC nibble
Input
FCC2: MII and HDLC Nibble: Receive Data Bit 1
RXD1 is bit 1 of the receive data nibble.
SI1 TDMA1: L1TXD1
TDM nibble
Output
Time-Division Multiplexing A1: Nibble Layer 1 Transmit Data Bit 1
L1TXD1 is bit 1 of the transmit data nibble.
SI2 TDMD2: L1RSYNC
TDM serial
Input
Time-Division Multiplexing D2: Layer 1 Receive Synchronize Data
The synchronizing signal for the receive channel.
FCC2: RXD2
MII and HDLC nibble
Input
FCC2: MII and HDLC Nibble Receive Data Bit 2
RXD2 is bit 2 of the receive data nibble.
I2C: SDA
Input/ Output I2C: Inter-Integrated Circuit Serial Data
The I2C interface comprises two signals: serial data (SDA) and serial
clock (SDA). The I2C controller uses a synchronous, multimaster bus
that can connect several integrated circuits on a board. Clock rates run
up to 520 kHz@25 MHz system clock.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
1-23
Signals/Connections
Table 1-8.
Port B Signals (Continued)
Name
GeneralPurpose I/O
PB18
Peripheral Controller:
Dedicated I/O
Protocol
FCC2: RXD3
MII and HDLC nibble
I2C: SCL
1.6.3
Dedicated
I/O Data
Direction
Input
Input/Output
Description
FCC2: MII and HDLC Nibble Receive Data Bit 3
RXD3 is bit 3 and the most significant bit of the receive data nibble.
I2C: Inter-Integrated Circuit Serial Clock
The I2C interface comprises two signals: serial data (SDA) and serial
clock (SDA). The I2C controller uses a synchronous, multimaster bus
that can connect several integrated circuits on a board. Clock rates run
up to 520 kHz@25 MHz system clock.
Port C Signals
Table 1-9.
Port C Signals
Name
GeneralPurpose I/O
PC31
Peripheral Controller:
Dedicated I/O
Protocol
BRG1O
Dedicated
I/O Data
Direction
Output
Description
Baud-Rate Generator 1 Output
The CPM supports up to 8 BRGs used internally by the bank-of-clocks
selection logic and/or to provide an output to one of the 8 BRG pins.
BRG1O can be the internal input to the SIU timers. When CLK5 is selected
(see PC27 below), it is the source for BRG1O which is the default input for
the SIU timers. See the system interface unit (SIU) chapter in the
MSC8101 Reference Manual for additional information. If CLK5 is not
enabled, BRG1O uses an internal input. If TMCLK is enabled (see PC26
below), the BRG1O input to the SIU timers is disabled.
CLK1
Input
Clock 1
The CPM supports up to 10 clock input pins sent to the bank-of-clocks
selection logic, where they can be routed to the controllers.
TIMER1/2: TGATE1
Input
Timer 1/2: Timer Gate 1
The timers can be gated/restarted by an external gate signal. There are
two gate signals: TGATE1 controls timer 1 and/or 2 and TGATE2 controls
timer 3 and/or 4.
MSC8101 Technical Data, Rev. 16
1-24
Freescale Semiconductor
CPM Ports
Table 1-9.
Port C Signals (Continued)
Name
GeneralPurpose I/O
PC30
Peripheral Controller:
Dedicated I/O
Protocol
BRG2O
CLK2
Timer1: TOUT1
EXT1
PC29
Dedicated
I/O Data
Direction
Description
Output
Baud-Rate Generator 2 Output
The CPM supports up to 8 BRGs used internally by the bank-of-clocks
selection logic and/or to provide an output to one of the 8 BRG pins.
Input
Clock 2
The CPM supports up to 10 clock input pins sent to the bank-of-clocks
selection logic, where they can be routed to the controllers.
Output
Timer 1: Timer Out 1
The timers (Timer[1–4]) can output a signal on a timer output (TOUT[1–4])
when the reference value is reached. This signal can be an active-low
pulse or a toggle of the current output. The output can also connect
internally to the input of another timer, resulting in a 32-bit timer.
Input
External Request 1
Asserts an internal request to the CPM processor. The signal can be
programmed as level- or edge-sensitive, and also has programmable
priority. Refer to the RISC Controller Configuration Register (RCCR)
description in the Chapter 17 of the MSC8101 Reference Manual for
programming information. There are no current microcode applications for
this request line. It is reserved for future development.
Output
Baud-Rate Generator 3 Output
The CPM supports up to 8 BRGs used internally by the bank-of-clocks
selection logic and/or to provide an output to one of the 8 BRG pins.
CLK3
Input
Clock 3
The CPM supports up to 10 clock input pins sent to the bank-of-clocks
selection logic, where they can be routed to the controllers.
TIN2
Input
Timer Input 2
A timer can have one of the following sources: another timer, system
clock, system clock divided by 16 or a timer input. The CPM supports up to
4 timer inputs. The timer inputs can be captured on the rising, falling or
both edges.
SCC1: CTS, CLSN
Input
SCC1: Clear to Send, Collision
Typically used in conjunction with RTS. The MSC8101 SCC1 transmitter
sends out a request to send data signal (RTS). The request is accepted
when CTS is returned low. CLSN is the signal used in Ethernet mode. See
also PC15.
BRG3O
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
1-25
Signals/Connections
Table 1-9.
Port C Signals (Continued)
Name
GeneralPurpose I/O
PC28
Peripheral Controller:
Dedicated I/O
Protocol
BRG4O
Description
Output
Baud-Rate Generator 4 Output
The CPM supports up to 8 BRGs used internally by the bank-of-clocks
selection logic and/or to provide an output to one of the 8 BRG pins.
CLK4
Input
Clock 4
The CPM supports up to 10 clock input pins sent to the bank-of-clocks
selection logic, where they can be routed to the controllers.
TIN1
Input
Timer Input 1
A timer can have one of the following sources: another timer, system
clock, system clock divided by 16 or a timer input. The CPM supports up to
4 timer inputs. The timer inputs can be captured on the rising, falling or
both edges.
Output
Timer 2: Timer Output 2
The timers (Timer[1–4]) can output a signal on a timer output (TOUT[1–4])
when the reference value is reached. This signal can be an active-low
pulse or a toggle of the current output. The output can also be connected
internally to the input of another timer, resulting in a 32-bit timer.
Input
SCC2: Clear to Send, Collision
Typically used in conjunction with RTS. The MSC8101 SCC2 transmitter
sends out a request to send data signal (RTS). The request is accepted
when CTS is returned low. CLSN is the signal used in Ethernet mode. See
also PC13.
Timer2: TOUT2
SCC2: CTS, CLSN
PC27
Dedicated
I/O Data
Direction
BRG5O
Output
Baud-Rate Generator 5 Output
The CPM supports up to 8 BRGs used internally by the bank-of-clocks
selection logic and/or to provide an output to one of the 8 BRG pins.
CLK5
Input
Clock 5
When selected, CLK5 is a source for the SIU timers via BRG1O. See the
System Interface Unit (SIU) chapter in the MSC8101 Reference Manual
for additional information. If CLK5 is not enabled, BRG1O uses an internal
input. If TMCLK is enabled (see PC26 below), the BRG1O input to the SIU
timers is disabled.
TIMER3/4: TGATE2
Input
Timer 3/4: Timer Gate 2
The timers can be gated/restarted by an external gate signal. There are
two gate signals: TGATE1 controls timer 1 and/or 2 and TGATE2 controls
timer 3 and/or 4.
MSC8101 Technical Data, Rev. 16
1-26
Freescale Semiconductor
CPM Ports
Table 1-9.
Port C Signals (Continued)
Name
GeneralPurpose I/O
PC26
Peripheral Controller:
Dedicated I/O
Protocol
BRG6O
CLK6
Timer3: TOUT3
PC25
Dedicated
I/O Data
Direction
Description
Output
Baud-Rate Generator 6 Output
The CPM supports up to 8 BRGs used internally by the bank-of-clocks
selection logic and/or provide an output to one of the 8 BRG pins.
Input
Clock 6
The CPM supports up to 10 clock input pins sent to the bank-of-clocks
selection logic, where they can be routed to the controllers.
Output
Timer 3: Timer Out 3
The timers (Timer[1–4]) can output a signal on a timer output (TOUT[1–4])
when the reference value is reached. This signal can be an active-low
pulse or a toggle of the current output. The output can also connect
internally to the input of another timer, resulting in a 32-bit timer.
TMCLK
Input
BRG7O
Output
Baud-Rate Generator 7 Output
The CPM supports up to 8 BRGs used internally by the bank-of-clocks
selection logic and/or provide an output to one of the 8 BRG pins.
CLK7
Input
Clock 7
The CPM supports up to 10 clock input pins sent to the bank-of-clocks
selection logic, where they can be routed to the controllers.
TIN4
Input
Timer Input 4
A timer can have one of the following sources: another timer, system
clock, system clock divided by 16 or a timer input. The CPM supports up to
4 timer inputs. The timer inputs can be captured on the rising, falling or
both edges.
Output
DMA: Data Acknowledge 2
DACK2, DREQ2, DRACK2 and DONE2 belong to the SIU DMA controller.
DONE2 and DRACK2 are signals on the same pin and therefore cannot be
used simultaneously. There are two sets of DMA pins associated with the
PIO ports.
DMA: DACK2
Timer Clock
When selected, TMCLK is the designated input to the SIU timers. When
TMCLK is configured as the input to the SIU timers, the BRG1O input is
disabled. See the System Interface Unit (SIU) chapter in the MSC8101
Reference Manual for additional information.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
1-27
Signals/Connections
Table 1-9.
Port C Signals (Continued)
Name
GeneralPurpose I/O
PC24
Peripheral Controller:
Dedicated I/O
Protocol
BRG8O
Output
Description
Baud-Rate Generator 8 Output
The CPM supports up to 8 BRGs used internally by the bank-of-clocks
selection logic and/or to provide an output to one of the 8 BRG pins.
CLK8
Input
Clock 8
The CPM supports up to 10 clock input pins. The clocks are sent to the
bank-of-clocks selection logic, where they can be routed to the controllers.
TIN3
Input
Timer Input 3
A timer can have one of the following sources: another timer, system
clock, system clock divided by 16, or a timer input. The CPM supports up
to four timer inputs. The timer inputs can be captured on the rising, falling,
or both edges.
Output
Timer 4: Timer Out 4
The timers (Timer1–4]) can output a signal on a timer output (TOUT[1–4])
when the reference value is reached. This signal can be an active-low
pulse or a toggle of the current output. The output can also be connected
internally to the input of another timer, resulting in a 32-bit timer.
DMA: DREQ2
Input
DMA: Data Request 2
DACK2, DREQ2, DRACK2, and DONE2 belong to the SIU DMA controller.
DONE2 and DRACK2 are signals on the same pin and therefore cannot be
used simultaneously. There are two sets of DMA pins associated with the
PIO ports.
CLK9
Input
Clock 9
The CPM supports up to 10 clock input pins sent to the bank-of-clocks
selection logic, where they can be routed to the controllers.
Timer4: TOUT4
PC23
Dedicated
I/O Data
Direction
DMA: DACK1
EXT2
Output
DMA: Data Acknowledge 1
DACK1, DREQ1, DRACK1, and DONE1 belong to the SIU DMA controller.
DONE1 and DRACK1 are signals on the same pin and therefore cannot be
used simultaneously. There are two sets of DMA pins associated with the
PIO ports.
Input
External Request 2
External request input line 2 asserts an internal request to the CPM
processor. The signal can be programmed as level- or edge-sensitive, and
also has programmable priority. Refer to the risc controller configuration
register (RCCR) description in the Chapter 17 of the MSC8101 Reference
Manual for programming information. There are no current microcode
applications for this request line. It is reserved for future development.
MSC8101 Technical Data, Rev. 16
1-28
Freescale Semiconductor
CPM Ports
Table 1-9.
Port C Signals (Continued)
Name
GeneralPurpose I/O
PC22
Peripheral Controller:
Dedicated I/O
Protocol
SI1: L1ST1
CLK10
DMA: DREQ1
PC15
PC14
SMC2: SMTXD
Dedicated
I/O Data
Direction
Output
Input
Description
Serial Interface 1: Layer 1 Strobe 1
The MSC8101 time-slot assigner supports up to four strobe outputs that
can be asserted on a bit or byte basis. The strobe outputs are useful for
interfacing to other devices that do not support the multiplexed interface or
for enabling/disabling three-state I/O buffers in a multiple-transmitter
architecture. These strobes can also generate output wave forms for such
applications as stepper-motor control.
Clock 10
The CPM supports up to 10 clock input pins sent to the bank-of-clocks
selection logic, where they can be routed to the controllers.
Input/ Output DMA: Request 1
DACK1, DREQ1, DRACK1, and DONE1 belong to the SIU DMA controller.
DONE1 and DRACK1 are signals on the same pin and therefore cannot be
used simultaneously. There are two sets of DMA pins associated with the
PIO ports.
Output
SMC2: Serial Management Transmit Data
The SMC interface consists of SMTXD, SMRXD, SMSYN, and a clock. Not
all signals are used for all applications. SMCs are full-duplex ports that
support three protocols or modes: UART, transparent, or general-circuit
interface (GCI). See also PA9.
SCC1: CTS/CLSN
Input
SCC1: Clear To Send, Collision
Typically used in conjunction with RTS. The MSC8101 SCC1 transmitter
sends out a request to send data signal (RTS). The request is accepted
when CTS is returned low. CLSN is the signal used in Ethernet mode. See
also PC29.
FCC1: TXADDR0
UTOPIA master
Output
FCC1: TXADDR0
UTOPIA slave
Input
FCC1: UTOPIA Master Transmit Address Bit 0
This is master transmit address bit 0.
FCC1: UTOPIA Slave Transmit Address Bit 0
This is slave transmit address bit 0.
Output
Serial Interface 1: Layer 1 Strobe 2
The MSC8101 time-slot assigner supports up to four strobe outputs that
can be asserted on a bit or byte basis. The strobe outputs are useful for
interfacing to other devices that do not support the multiplexed interface or
for enabling/disabling three-state I/O buffers in a multiple-transmitter
architecture. These strobes can also be generate output wave forms for
such applications as stepper-motor control.
SCC1: CD, RENA
Input
SCC1: Carrier Detect, Receive Enable
Typically used in conjunction with RTS supported by SCC1. The
MSC8101MSC8101 SCC1 transmitter requests the receiver to send data
by asserting RTS low. The request is accepted when CTS is returned low.
FCC1: RXADDR0
UTOPIA master
Output
FCC1: RXADDR0
UTOPIA slave
Input
SI1: L1ST2
FCC1: UTOPIA Multi-PHY Master Receive Address Bit 0
This is master receive address bit 0.
FCC1: UTOPIA Multi-PHY Slave Receive Address Bit 0
This is slave receive address bit 0.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
1-29
Signals/Connections
Table 1-9.
Port C Signals (Continued)
Name
GeneralPurpose I/O
PC13
Peripheral Controller:
Dedicated I/O
Protocol
SI1: L1ST4
SCC2: CTS,CLSN
PC12
Dedicated
I/O Data
Direction
Description
Output
Serial Interface 1: Layer 1 Strobe 4
The MSC8101 time-slot assigner supports up to four strobe outputs that
can be asserted on a bit or byte basis. The strobe outputs are useful for
interfacing to other devices that do not support the multiplexed interface or
for enabling/disabling three-state I/O buffers in a multiple-transmitter
architecture. These strobes can also generate output wave forms for such
applications as stepper-motor control.
Input
SCC2: Clear to Send, Collision
Typically used in conjunction with RTS. The MSC8101 SCC2 transmitter
sends out a request to send data signal (RTS). The request is accepted
when CTS is returned low. CLSN is the signal used in Ethernet mode. See
also PC28.
FCC1:TXADDR1
UTOPIA master
Output
FCC1: TXADDR1
UTOPIA slave
Input
FCC1: UTOPIA Multi-PHY Master Transmit Address Bit 1
This is master transmit address bit 1.
FCC1: UTOPIA Multi-PHY Slave Transmit Address Bit 1
This is slave transmit address bit 1.
Output
Serial Interface 1: Layer 1 Strobe 3
The MSC8101 time-slot assigner supports up to four strobe outputs that
can be asserted on a bit or byte basis. The strobe outputs are useful for
interfacing to other devices that do not support the multiplexed interface or
for enabling/disabling three-state I/O buffers in a multiple-transmitter
architecture. These strobes can also generate output wave forms for such
applications as stepper-motor control.
SCC2: CD, RENA
Input
SCC2: Carrier Detect, Request Enable
Typically used in conjunction with RTS supported by SCC2. The MSC8101
SCC2 transmitter requests to the receiver that it sends data by asserting
RTS low. The request is accepted when CTS is returned low.
FCC1: RXADDR1
UTOPIA master
Output
FCC1: RXADDR1
UTOPIA slave
Input
SI1: L1ST3
FCC1: UTOPIA Multi-PHY Master Receive Address Bit 1
This is master receive address bit 1.
FCC1: UTOPIA Multi-PHY Slave Receive Address Bit 1
This is slave receive address bit 1.
MSC8101 Technical Data, Rev. 16
1-30
Freescale Semiconductor
CPM Ports
Table 1-9.
Port C Signals (Continued)
Name
GeneralPurpose I/O
PC7
Peripheral Controller:
Dedicated I/O
Protocol
SI2: L1ST1
FCC1: CTS
HDLC serial, HDLC nibble,
and transparent
PC6
Dedicated
I/O Data
Direction
Description
Output
Serial Interface 2: Strobe 1
The MSC8101 time-slot assigner supports up to four strobe outputs that
can be asserted on a bit or byte basis. The strobe outputs are useful for
interfacing to other devices that do not support the multiplexed interface or
for enabling/disabling three-state I/O buffers in a multiple-transmitter
architecture. These strobes can also generate output wave forms for such
applications as stepper-motor control.
Input
FCC1: Clear To Send
In the standard modem interface signals supported by FCC1 (RTS, CTS,
and CD). CTS is asynchronous with the data.
FCC1: UTOPIA Multi-PHY Master Transmit Address Bit 2
This is master transmit address bit 2.
FCC1: TXADDR2
UTOPIA master
Output
FCC1: TXADDR2
UTOPIA slave
Input
FCC1: UTOPIA Multi-PHY Slave Transmit Address Bit 2
This is slave transmit address bit 2.
FCC1: TXCLAV1
UTOPIA multi-PHY master, direct
polling
Input
FCC1: UTOPIA Multi-PHY Master Transmit Cell Available 1 Direct
Polling
Asserted by an external UTOPIA slave PHY to indicate that it can accept
one complete ATM cell.
Output
Serial Interface 2: Layer 1 Strobe 2
The MSC8101 time-slot assigner supports up to four strobe outputs that
can be asserted on a bit or byte basis. The strobe outputs are useful for
interfacing to other devices that do not support the multiplexed interface or
for enabling/disabling three-state I/O buffers in a multiple-transmitter
architecture. These strobes can also generate output wave forms for such
applications as stepper-motor control.
Input
FCC1: Carrier Detect
In the standard modem interface signals supported by FCC1 (RTS, CTS,
and CD). CD is an input asynchronous with the data.
SI2: L1ST2
FCC1: CD
HDLC serial, HDLC nibble,
and transparent
FCC1: RXADDR2
UTOPIA master
Output
FCC1: RXADDR2
UTOPIA slave
Input
FCC1: UTOPIA Slave Receive Address Bit 2
This is slave receive address bit 2.
FCC1: RXCLAV1
UTOPIA multi-PHY master, direct
polling
Input
FCC1: UTOPIA Multi-PHY Master Receive Cell Available 1 Direct
Polling
Asserted by an external PHY when one complete ATM cell is available for
transfer.
FCC1: UTOPIA Multi-PHY Master Receive Address Bit 2
This is master receive address bit 2.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
1-31
Signals/Connections
Table 1-9.
Port C Signals (Continued)
Name
GeneralPurpose I/O
PC5
PC4
Peripheral Controller:
Dedicated I/O
Protocol
Dedicated
I/O Data
Direction
Description
SMC1: SMTXD
Output
SMC1: Transmit Data
The SMC interface consists of SMTXD, SMRXD, SMSYN, and a clock. Not
all signals are used for all applications. SMCs are full-duplex ports that
supports three protocols or modes: UART, transparent, or general-circuit
interface (GCI).
SI2: L1ST3
Output
Serial Interface 2: Layer 1 Strobe 3
The MSC8101 time-slot assigner supports up to four strobe outputs that
can be asserted on a bit or byte basis. The strobe outputs are useful for
interfacing to other devices that do not support the multiplexed interface or
for enabling/disabling three-state I/O buffers in a multiple-transmitter
architecture. These strobes can also generate output wave forms for such
applications as stepper-motor control.
FCC2: CTS
HDLC serial, HDLC nibble,
and transparent
Input
FCC2: Clear To Send
In the standard modem interface signals supported by FCC2 (RTS, CTS,
and CD). CTS is asynchronous with the data.
SMC1: SMRXD
Input
SMC1: Receive Data
The SMC interface consists of SMTXD, SMRXD, SMSYN, and a clock. Not
all signals are used for all applications. SMCs are full-duplex ports that
supports three protocols or modes: UART, transparent, or general-circuit
interface (GCI).
Output
Serial Interface 2: Layer 1 Strobe 4
The MSC8101 time-slot assigner supports up to four strobe outputs that
can be asserted on a bit or byte basis. The strobe outputs are useful for
interfacing to other devices that do not support the multiplexed interface or
for enabling/disabling three-state I/O buffers in a multiple-transmitter
architecture. These strobes can also generate output wave forms for such
applications as stepper-motor control.
SI2: L1ST4
FCC2: CD
HDLC serial, HDLC nibble,
and transparent
Input
FCC2: Carrier Detect
In the standard modem interface signals supported by FCC2 (RTS, CTS
and CD). CD is asynchronous with the data.
MSC8101 Technical Data, Rev. 16
1-32
Freescale Semiconductor
CPM Ports
1.6.4
Port D Signals
Table 1-10.
Port D Signals
Name
GeneralPurpose I/O
PD31
Peripheral Controller:
Dedicated I/O
Protocol
SCC1: RXD
DMA: DRACK1
DMA: DONE1
PD30
Input
Description
SCC1: Receive Data
SCC1 receives serial data from RXD.
Output
DMA: Data Request Acknowledge 1
DACK1, DREQ1, DRACK1, and DONE1 belong to the SIU DMA
controller. DONE1 and DRACK1 are signals on the same pin and
therefore cannot be used simultaneously. There are two sets of DMA
pins associated with the PIO ports.
Input/ Output
DMA: Done 1
DACK1, DREQ1, DRACK1, and DONE1 belong to the SIU DMA
controller. DONE1 and DRACK1 are signals on the same pin and
therefore cannot be used simultaneously. There are two sets of DMA
pins associated with the PIO ports.
SCC1: TXD
Output
SCC1: Transmit Data
SCC1 transmits serial data out of TXD.
DMA: DRACK2
Output
DMA: Data Request Acknowledge 2
DACK2, DREQ2, DRACK2, and DONE2 belong to the SIU DMA
controller. DONE2 and DRACK2 are signals on the same pin and
therefore cannot be used simultaneously. There are two sets of DMA
pins associated with the PIO ports.
Input/ Output
DMA: Done 2
DACK2, DREQ2, DRACK2, and DONE2 belong to the SIU DMA
controller. DONE2 and DRACK2 are signals on the same pin and
therefore cannot be used simultaneously. There are two sets of DMA
pins associated with the PIO ports.
DMA: DONE2
PD29
Dedicated
I/O Data
Direction
SCC1: RTS, TENA
Output
SCC1: Request to Send, Transmit Enable
Typically used in conjunction with CD supported by SCC2. The
MSC8101 SCC1 transmitter requests the receiver to send data by
asserting RTS low. The request is accepted when CTS is returned low.
TENA is the signal used in Ethernet mode.
FCC1: RXADDR3
UTOPIA master
Output
FCC1: UTOPIA Multi-PHY Master Receive Address Bit 3
This is master receive address bit 3.
FCC1: RXADDR3
UTOPIA slave
Input
FCC1: UTOPIA Slave Receive Address Bit 3
This is slave receive address bit 3.
FCC1: RXCLAV2
UTOPIA multi-PHY master, direct
polling
Input
FCC1: UTOPIA Multi-PHY Master Receive Cell Available 2 Direct
Polling
Asserted by an external PHY when one complete ATM cell is available
for transfer.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
1-33
Signals/Connections
Table 1-10.
Port D Signals (Continued)
Name
GeneralPurpose I/O
PD19
Peripheral Controller:
Dedicated I/O
Protocol
Description
FCC1: Multi-PHY Master Transmit Address Bit 4 Multiplexed Polling
This is master transmit address bit 4.
FCC1: TXADDR4
UTOPIA master
Output
FCC1: TXADDR4
UTOPIA slave
Input
FCC1: UTOPIA Slave Transmit Address Bit 4
This is slave transmit address bit 4.
FCC1: TXCLAV3
UTOPIA multi-PHY master, direct
polling
Input
FCC1: UTOPIA Multi-PHY master Transmit Cell Available 3 Direct
Polling
Asserted by an external UTOPIA slave PHY to indicate that it can accept
one complete ATM cell.
Output
Baud Rate Generator 1 Output
The CPM supports up to 8 BRGs for use internally by the bank-of-clocks
selection logic and/or to provide an output to one of the 8 BRG pins.
BRG1O can be the internal input to the SIU timers. When CLK5 is
selected (see PC27 above), it is the source for BRG1O which is the
default input for the SIU timers. See the system interface unit (SIU)
chapter in the MSC8101 Reference Manual for additional information. If
CLK5 is not enabled, BRG1O uses an internal input. If TMCLK is
enabled (see PC26 above), the BRG1O input to the SIU timers is
disabled.
Input
SPI: Select
The SPI interface comprises four signals: master out slave in
(SPIMOSI), master in slave out (SPIMISO), clock (SPICLK) and select
(SPISEL). The SPI can be configured as a slave or master in single- or
multiple-master environments. SPISEL is the enable input to the SPI
slave. In a multimaster environment, SPISEL (always an input) detects
an error when more than one master is operating. SPI masters must
output a slave select signal to enable SPI slave devices by using a
separate general-purpose I/O signal. Assertion of an SPI SPISEL while
it is master causes an error.
BRG1O
SPI: SPISEL
PD18
Dedicated
I/O Data
Direction
FCC1: RXADDR4
UTOPIA master
Output
FCC1: RXADDR4
UTOPIA slave
Input
FCC1: UTOPIA Slave Receive Address Bit 4
This is slave receive address bit 4.
FCC1: RXCLAV3
UTOPIA multi-PHY master, direct
polling
Input
FCC1: UTOPIA Multi-PHY Master Receive Cell Available 3 Direct
Polling
Asserted by an external PHY when one complete ATM cell is available
for transfer.
Input/ Output
SPI: Clock
The SPI interface comprises four signals: master out slave in
(SPIMOSI), master in slave out (SPIMISO), clock (SPICLK) and select
(SPISEL). The SPI can be configured as a slave or master in single- or
multiple-master environments. SPICLK is a gated clock, active only
during data transfers. Four combinations of SPICLK phase and polarity
can be configured. When the SPI is a master, SPICLK is the clock
output signal that shifts received data in from SPIMISO and transmitted
data out to SPIMOSI.
SPI: SPICLK
FCC1: UTOPIA Master Receive Address Bit 4
This is master receive address bit 4.
MSC8101 Technical Data, Rev. 16
1-34
Freescale Semiconductor
CPM Ports
Table 1-10.
Port D Signals (Continued)
Name
GeneralPurpose I/O
PD17
Peripheral Controller:
Dedicated I/O
Protocol
BRG2O
FCC1: RXPRTY
UTOPIA
SPI: SPIMOSI
PD16
FCC1: TXPRTY
UTOPIA
SPI: SPIMISO
PD7
SMC1: SMSYN
Dedicated
I/O Data
Direction
Output
Input
Input/ Output
Output
Description
Baud Rate Generator 2 Output
The CPM supports up to 8 BRGs for use internally to the MSC8101
and/or to provide an output to one of the 8 BRG pins.
FCC1: UTOPIA Receive Parity
This is the odd parity bit for RXD[0–7].
SPI: Master Output Slave Input
The SPI interface comprises our signals: master out slave in (SPIMOSI),
master in slave out (SPIMISO), clock (SPICLK) and select (SPISEL).
The SPI can be configured as a slave or master in single- or multiplemaster environments. When the SPI is a slave, SPICLK is the clock
input that shifts received data in from SPIMOSI and transmitted data out
through SPIMISO.
FCC1: UTOPIA Transmit Parity
This is the odd parity bit for TXD[0–7].
Input/ Output
SPI: Master Input Slave Output
The SPI interface comprises four signals: master out slave in
(SPIMOSI), master in slave out (SPIMISO), clock (SPICLK), and select
(SPISEL). The SPI can be configured as a slave or master in single- or
multiple-master environments. When the SPI is a slave, SPICLK is the
clock input that shifts received data in from SPIMOSI and transmitted
data out through SPIMISO.
Input
SMC1: Serial Management Synchronization
The SMC interface consists of SMTXD, SMRXD, SMSYN and a clock.
Not all signals are used for all applications. SMCs are full-duplex ports
that support three protocols or modes: UART, transparent or generalcircuit interface (GCI).
FCC1: TXADDR3
UTOPIA master
Output
FCC1: TXADDR3
UTOPIA slave
Input
FCC1: UTOPIA Slave Transmit Address Bit 3
This is slave transmit address bit 3.
FCC1: TXCLAV2
UTOPIA multi-PHY master, direct
polling
Input
FCC1: UTOPIA Multi-PHY Master Transmit Cell Available 2 Direct
Polling
Asserted by an external UTOPIA slave PHY to indicate that it can accept
one complete ATM cell.
FCC1: UTOPIA Master Transmit Address Bit 3
This is master transmit address bit 3.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
1-35
Signals/Connections
1.7 JTAG Test Access Port Signals
The MSC8101 supports the standard set of Test Access Port (TAP) signals defined by IEEE 1149.1 Standard Test
Access Port and Boundary-Scan Architecture specification and described in Table 1-11.
Table 1-11.
JTAG Test Access Port Signals
Signal Name
Type
Signal Description
TCK
Input
Test Clock
A test clock signal for synchronizing JTAG test logic.
TDI
Input
Test Data Input
A test data serial signal for test instructions and data. TDI is sampled on the rising edge of TCK and
has an internal pull-up resistor.
TDO
Output
Test Data Output
A test data serial signal for test instructions and data. TDO can be tri-stated. The signal is actively
driven in the shift-IR and shift-DR controller states and changes on the falling edge of TCK.
TMS
Input
Test Mode Select
Sequences the test controller’s state machine, is sampled on the rising edge of TCK, and has an
internal pull-up resistor.
TRST
Input
Test Reset
Asynchronously initializes the test controller, has an internal pull-up resistor, and must be asserted
after power up.
1.8 Reserved Signals
Table 1-12.
Signal Name
TEST
Type
Input
Reserved Signals
Signal Description
Test
Used for manufacturing testing. You must connect this input to GND.
THERM[1–2]
—
Leave disconnected.
SPARE1, 5
—
Spare Pins
Leave disconnected for backward compatibility with future revisions of this device.
MSC8101 Technical Data, Rev. 16
1-36
Freescale Semiconductor
Physical and Electrical Specifications
2
This document contains detailed information on environmentatl limits, power considerations, DC/AC electrical
characteristics, and AC timing specifications for the MSC8101 communications processor, mask set 2K87M. For
additional information, see the MSC8101 Reference Manual.
2.1 Absolute Maximum Ratings
CAUTION
This device contains circuitry protecting against damage due to
high static voltage or electrical fields; however, normal precautions
should be taken to avoid exceeding maximum voltage ratings.
Reliability is enhanced if unused inputs are tied to an appropriate
logic voltage level (for example, either GND or VCC).
In calculating timing requirements, adding a maximum value of one specification to a minimum value of another
specification does not yield a reasonable sum. A maximum specification is calculated using a worst case variation
of process parameter values in one direction. The minimum specification is calculated using the worst case for the
same parameters in the opposite direction. Therefore, a “maximum” value for a specification never occurs in the
same device with a “minimum” value for another specification; adding a maximum to a minimum represents a
condition that can never exist. Table 2-1 describes the maximum electrical ratings for the MSC8101.
Table 2-1.
Rating
Core supply
Symbol
Value
Unit
VDD
–0.2 to 1.7
V
VCCSYN
–0.2 to 1.7
V
V DDH
–0.2 to 3.6
V
VIN
(GND – 0.2) to 3.6
V
TJ
–40 to 120
°C
TSTG
–55 to +150
°C
voltage3
3
PLL supply voltage
I/O supply
Absolute Maximum Ratings2
voltage3
Input voltage3
Maximum operating temperature
range4
Storage temperature range
Notes:
1.
2.
3.
4.
Functional operating conditions are given in Table 2-2.
Absolute maximum ratings are stress ratings only, and functional operation at the maximum is not guaranteed. Stress beyond
the listed limits may affect device reliability or cause permanent damage.
The input voltage must not exceed the I/O supply VDDH by more than 2.5 V at any time, including during power-on reset. In
turn, VDDH can exceed VDD /VCCSYN by more than 3.3 V during power-on reset, but for no more than 100 ms. VDDH should not
exceed VDD/V CCSYN by more than 2.1 V during normal operation. V DD/V CCSYN must not exceed VDDH by more than 0.4 V at
any time, including during power-on reset. See Section 4.2, Electrical Design Considerations, on page 4-1 for more
information.
Section 4.1, Thermal Design Considerations, on page 4-1 includes a formula for computing the chip junction temperature
(TJ ).
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
2-1
Physical and Electrical Specifications
2.2 Recommended Operating Conditions
Table 2-2 lists recommended operating conditions. Proper device operation outside of these conditions is not
guaranteed.
Table 2-2.
Recommended Operating Conditions
Rating
Symbol
Value
Unit
VDD
250/275 MHz: 1.5 to 1.7
300 MHz: 1.55 to 1.7
V
V
PLL supply voltage
VCCSYN
250/275 MHz: 1.5 to 1.7
300 MHz: 1.55 to 1.7
V
V
I/O supply voltage
VDDH
3.135 to 3.465
V
SC140 core supply voltage
Input voltage
VIN
–0.2 to VDDH + 0.2
V
Operating temperature range
TJ
250/275 MHz: –40 to 105
300 MHz: –40 to 75
°C
°C
2.3 Thermal Characteristics
Table 2-3 describes thermal characteristics of the MSC8101.
Table 2-3.
Characteristic
Junction-to-ambient, single-layer board1, 2
Junction-to-ambient, four-layer
Junction-to-board3
Junction-to-case
Notes:
1.
2.
3.
4.
5.
4
board1, 3
Thermal Characteristics
Lidded FC-PBGA
17 × 17 mm
Symbol
Unit
Natural Convection
200 ft/min
(1 m/s) airflow
RθJA or θJA
50
37
°C/W
RθJA or θJA
22
18
°C/W
RθJB or θJB
15
°C/W
RθJC or θJC
TBD
°C/W
Junction temperature is a function of on-chip power dissipation, package thermal resistance, mounting site (board)
temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal
resistance.
Per SEMI G38-87 and EIA/JESD51-2 with the single layer board horizontal.
Per JEDEC JESD51-6 with the board (JESD51-9) horizontal.
Thermal resistance between the die and the printed circuit board per JEDEC JESD 51-8. Board temperature is measured on
the top surface of the board near the package.
Thermal resistance between the die and the case top surface without thermal grease. TBD = to be determined. If a thin (less
than 50 micron) thermal grease interface is established to a heat sink from the lid, the junction to sink thermal resistance is
about 0.7 °C/W.
See Section 4.1, Thermal Design Considerations, on page 4-1 for details on these characteristics.
MSC8101 Technical Data, Rev. 16
2-2
Freescale Semiconductor
DC Electrical Characteristics
2.4 DC Electrical Characteristics
This section describes the DC electrical characteristics for the MSC8101. The measurements in Table 2-4 assume
the following system conditions:
• TJ = 0 – 100 °C
• VDD = 1.6 V ± 5% VDC
• VDDH = 3.3 V ± 5% VDC
• GND = 0 VDC
Note: The leakage current is measured for nominal VDDH and VDD or both VDDH and VDD must vary in the same
direction (for example, both VDDH and VDD vary by ± 5 percent).
Table 2-4.
Characteristic
Input high voltage, all inputs except CLKIN
Input low voltage
DC Electrical Characteristics
Symbol
Min
Max
Unit
VIH
2.0
3.465
V
VIL
GND
0.8
V
CLKIN input high voltage
V IHC
2.5
3.465
V
CLKIN input low voltage1
VILC
GND
0.8
V
Input leakage current, VIN = VDDH
IIN
—
10
µA
Tri-state (high impedance off state) leakage current,
VIN = VDDH
IOZ
—
10
µA
Signal low input current2, VIL = 0.4 V
IL
—
–4.0
mA
Signal high input current2, VIH = 2.0 V
IH
—
4.0
mA
Output high voltage, IOH = –2 mA, except open drain pins
VOH
2.4
—
V
Output low voltage, IOL= 3.2 mA
V OL
—
0.4
V
Symbol
Typical
Unit
Core power dissipation at 300 MHz
PCORE
450
mW
CPM power dissipation at 200 MHz
PCPM
320
mW
SIU power dissipation at 100 MHz
PSIU
80
mW
Core leakage power
PLCO
3
mW
CPM leakage power
PLCP
6
mW
SIU leakage power
PLSI
2
mW
Notes:
1.
2.
The optimum CLKIN duty cycle is obtained when: VILC = VDDH – VIHC .
Not tested. Guaranteed by design.
Table 2-5.
Typical Power Dissipation
Characteristic
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
2-3
Physical and Electrical Specifications
2.5 Clock Configuration
The following sections provide a general description of clock configuration.
2.5.1
Valid Clock Modes
Table 2-6 shows the maximum frequency values for each rated core frequency (250, 275, or 300 MHz). The user
must ensure that maximum frequency values are not exceeded.
Table 2-6.
Maximum Frequencies
Characteristic
Maximum Frequency in MHz
Core Frequency
CPM Frequency (CPMCLK)
Bus Frequency (BCLK)
250
275
166.67
183.33
300
200
83.33
91.67
100
Serial Communication Controller Clock Frequency (SCLK)
83.33
91.67
100
Baud Rate Generator Clock Frequency (BRGCLK)
83.33
91.67
100
External Clock Output Frequency (CLKOUT)
83.33
91.67
100
Six bit values map the MSC8101 clocks to one of the valid configuration mode options. Each option determines the
CLKIN, SC140, system bus, SCC clock, CPM, and CLKOUT frequencies. The six bit values are derived from three
dedicated input pins (MODCK[1–3]) and three bits from the hard reset configuration word (MODCK_H). To
configure the SPLL pre-division factor, SPLL multiplication factor, and the frequencies for the SC140, SCC
clocks, CPM parallel I/O ports, and system buses, the MODCK[1–3] pins are sampled and combined with the
MODCK_H values when the internal power-on reset (internal PORESET) is deasserted. Clock configuration
changes only when the internal PORESET signal is deasserted. The following factors are configured:
• SPLL pre-division factor (SPLL PDF)
• SPLL multiplication factor (SPLL MF)
• Bus post-division factor (Bus DF)
• CPM division factor (CPM DF)
• Core division factor (Core DF)
• CPLL pre-division factor (CPLL PDF)
• CPLL multiplication factor (CPLL MF)
The SCC division factor (SCC DF) is fixed at 4. The BRG division factor (BRG DF) is configured through the
System Clock Control Register (SCCR) and can be 4, 16 (default after reset), 64, or 256.
Note: Refer to Clock Mode Selection for MSC8101 and MSC8103 Mask Set 2K87M (AN2306) for details on
clock configuration.
2.5.2
Clocks Programming Model
This section describes the clock registers in detail. The registers discussed are as follows:
• System Clock Control Register (SCCR)
• System Clock Mode Register (SCMR)
MSC8101 Technical Data, Rev. 16
2-4
Freescale Semiconductor
Clock Configuration
2.5.2.1 System Clock Control Register
Bit
0
1
2
3
4
5
6
7
8
9
10
25
26
11
12
27
28
13
14
15
29
30
31
—
Type
Reserved
Reset
—
Bit
16
17
18
19
20
21
22
23
24
—
CLKODIS
—
Type
Reserved
R/W
Reserved
Reset
—
0
—
Figure 2-1.
DFBRG
R/W
0
1
System Clock Control Register (SCCR)—0x10C80
SCCR is memory-mapped into the SIU register map of the MSC8101.
Table 2-7.
SCCR Bit Descriptions
Defaults
Name
Bit No.
Description
PORESET
Hard Reset
—
0–26
—
—
CLKODIS
27
0
Unaffected
—
28–29
—
—
DFBRG
30–31
01
Unaffected
Settings
Reserved. Write to 0 fro future compatibility.
CLKOUT Disable
Disables the CLKOUT signal. The value of
CLKOUT when disabled is indeterminate (can be 1
or 0).
0
1
CLKOUT enabled (default)
CLKOUT disabled
00
01
10
11
Divide by 4
Divide by 16 (default value)
Divide by 64
Divide by 256
Reserved. Write to 0 fro future compatibility.
Division Factor for the BRG Clock Defines the
BRGCLK frequency. Changing this value does not
result in a loss of lock condition.
2.5.2.2 System Clock Mode Register
Bit
0
1
2
3
4
COREPDF
5
6
7
8
COREMF
R
Reset
—
16
17
18
19
20
SPLLPDF
21
22
23
SPLLMF
Type
R
Reset
—
Figure 2-2.
10
11
12
BUSDF
Type
Bit
9
24
25
—
DLLDIS
13
14
15
CPMDF
26
27
—
28
29
30
31
COREDF
System Clock Mode Register (SCMR)—0x10C88
SCMR is a read-only register that is updated during power-on reset (PORESET) and provides the mode control
signals to the PLLs, DLL, and clock logic. This register reflects the currently defined configuration settings. For
details of the available setting options, see AN2306/D.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
2-5
Physical and Electrical Specifications
Table 2-8.
Name
Bit No.
SCMR Field Descriptions
Defaults
Description
Settings
PORESET
Hard Reset
COREPDF
0–3
Configuration
Pins
Unaffected
Core PLL Pre-Division Factor
0000
0001
0010
0011
All other
CPLL PDF = 1
CPLL PDF = 2
CPLL PDF = 3
CPLL PDF = 4
combinations not used.
COREMF
4–7
Configuration
Pins
Unaffected
Core Multiplication Factor
0101
0110
0111
All other
CPLL MF = 10
CPLL MF = 12
CPLL MF = 14
combinations not used.
BUSDF
8–11
Configuration
Pins
Unaffected
60x-compatible Bus Division Factor
0001
0010
0011
0100
0101
All other
Bus DF = 2
Bus DF = 3
Bus DF = 4
Bus DF = 5
Bus DF = 6
combinations not used.
CPMDF
12–15
Configuration
Pins
Unaffected
CPM Division Factor
0000
0001
0010
All other
CPM DF = 1
CPM DF = 2
CPM DF = 3
combinations not used.
SPLLPDF
16–19
Configuration
Pins
Unaffected
SPLL Pre-Division Factor
0000
0001
0010
0011
0100
0101
All other
SPLL PDF = 1
SPLL PDF = 2
SPLL PDF = 3
SPLL PDF = 4
SPLL PDF = 5
SPLL PDF = 6
combinations not used
SPLLMF
20–23
Configuration
Pins
Unaffected
SPLL Multiplication Factor
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
All other
SPLL MF = 10
SPLL MF = 12
SPLL MF = 14
SPLL MF = 16
SPLL MF = 18
SPLL MF = 20
SPLL MF = 22
SPLL MF = 24
SPLL MF = 26
SPLL MF = 28
SPLL MF = 30
combinations not used
—
24
—
—
DLLDIS
25
Configuration
Pins
Unaffected
—
26–27
—
—
COREDF
28–31
Configuration
Pins
Unaffected
Reserved
DLL Disable
0
1
DLL operation is enabled
DLL is disabled
Reserved
Core Division Factor
0000
0001
0010
0011
0100
0101
All other
CORE DF = 1
CORE DF = 2
CORE DF = 3
CORE DF = 4
CORE DF = 5
CORE DF = 6
combinations not used.
MSC8101 Technical Data, Rev. 16
2-6
Freescale Semiconductor
AC Timings
2.6 AC Timings
The following sections include illustrations and tables of clock diagrams, signals, and parallel I/O outputs and
inputs. AC timings are based on a 50 pF load, except where noted otherwise, and 50 Ω transmission line.
2.6.1
Output Buffer Impedances
Table 2-9.
Output Buffer Impedances
Output Buffers
Typical Impedance (Ω)
System Bus
35
Memory Controller
35
Parallel I/O
55
Note:
These are typical values at 65°C. The impedance may vary by ±25% depending on device process and operating temperature.
2.6.2
Clocking and Timing Characteristics
Table 2-10.
System Clock Parameters
Characteristic
Minimum
Maximum
Unit
—
0.5
ns
18
75
MHz
CLKIN slope
—
5
ns
DLLIN slope
—
2
ns
CLKOUT frequency jitter
—
(0.01/CLKOUT) + CLKIN jitter
ns
Delay between CLKOUT and DLLIN
—
5
ns
Phase Jitter between BCLK and DLLIN
CLKIN
Notes:
frequency1,2
1.
2.
Low CLKIN frequency causes poor PLL performance. Choose a CLKIN frequency high enough to keep the frequency after the
predivider (SPLLMFCLK) higher than 18 MHz.
CLKIN should have a 50% ± 5% duty cycle.
Table 2-11.
Clock Ranges
Maximum Rated Core Frequency
Clock
Symbol
All
Max. Values for SC140 Clock Rating of:
Min
250 MHz
275 MHz
300 MHz
CLKIN
18 MHz
83.3
91.67 MHz
100 MHz
SPLLMFCLK
18 MHz
31.25
34.38 MHz
37.5 MHz
BCLK
CLKOUT
18 MHz
83.3 MHz
91.67 MHz
100 MHz
SCLK
35 MHz
83.3 MHz
91.67 MHz
100 MHz
Communications Processor Module
CPMCLK
70 MHz
166.7 MHz
183.3 MHz
200 MHz
SC140 Core
DSPCLK
72 MHz
250 MHz
275 MHz
300 MHz
Input Clock
SPLL MF Clock
Bus/Output
Serial Communications Controller
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
2-7
Physical and Electrical Specifications
Table 2-11.
Clock Ranges (Continued)
Maximum Rated Core Frequency
Clock
Symbol
Baud Rate Generator
• For BRG DF = 4
• For BRG DF = 16 (default)
• For BRG DF = 64
• For BRG DF = 256
2.6.3
All
Max. Values for SC140 Clock Rating of:
Min
250 MHz
275 MHz
300 MHz
36 MHz
9 MHz
2.25 MHz
562.5 KHz
83.3 MHz
20.83 MHz
5.21 MHz
1.3 MHz
91.67 MHz
22.91 MHz
5.73 MHz
1.43 MHz
100 MHz
25 MHz
6.25 MHz
1.56 MHz
BRGCLK
Reset Timing
The MSC8101 has several inputs to the reset logic:
• Power-on reset (PORESET)
• External hard reset (HRESET)
• External soft reset (SRESET)
Asserting an external PORESET causes concurrent assertion of an internal PORESET signal, HRESET, and SRESET.
When the external PORESET signal is deasserted, the MSC8101 samples several configuration pins:
• RSTCONF—determines whether the MSC8101 is a master (0) or slave (1) device
• DBREQ—determines whether to operate in normal mode (0) or invoke the SC140 debug mode (1)
• HPE—disable (0) or enable (1) the host port (HDI16)
• BTM[0–1]—boot from external memory (00) or the HDI16 (01)
All these reset sources are fed into the reset controller, which takes different actions depending on the source of the
reset. The reset status register indicates the last sources to cause a reset. Table 2-12 describes reset causes.
Table 2-12.
Name
Power-on reset
(PORESET)
Direction
Input
Reset Causes
Description
PORESET initiates the power-on reset flow that resets all the MSC8101s and configures
various attributes of the MSC8101, including its clock mode.
Hard reset
(HRESET)
Input/Output
The MSC8101 can detect an external assertion of HRESET only if it occurs while the
MSC8101 is not asserting reset. During HRESET, SRESET is asserted. HRESET is an opendrain pin.
Soft reset
(SRESET)
Input/Output
The MSC8101 can detect an external assertion of SRESET only if it occurs while the
MSC8101 is not asserting reset. SRESET is an open-drain pin.
2.6.3.1 Reset Operation
The reset control logic determines the cause of a reset, synchronizes it if necessary, and resets the appropriate logic
modules. The memory controller, system protection logic, interrupt controller, and parallel I/O pins are initialized
only on hard reset. Soft reset initializes the internal logic while maintaining the system configuration. The
MSC8101 has three mechanisms for reset configuration: host reset configuration, hardware reset configuration, and
reduced reset configuration.
MSC8101 Technical Data, Rev. 16
2-8
Freescale Semiconductor
AC Timings
2.6.3.2 Power-On Reset Flow
Asserting the PORESET external pin initiates the power-on reset flow. PORESET should be asserted externally for at
least 16 input clock cycles after external power to the MSC8101 reaches at least 2/3 VCC. As Table 2-13 shows, the
MSC8101 has five configuration pins, four of which are multiplexed with the SC140 EONCE Event (EE[0–1],
EE[4–5]) pins and the fifth of which is the RSTCONF pin. These pins are sampled at the rising edge of PORESET. In
addition to these configuration pins, three (MODCK[1–3]) pins are sampled by the MSC8101. The signals on these
pins and the MODCK_H value in the Hard Reset Configuration Word determine the PLL locking mode, by
defining the ratio between the DSP clock, the bus clocks, and the CPM clock frequencies.
Table 2-13.
Pin
External Configuration Signals
Description
Settings
RSTCONF
Reset Configuration
Input line sampled by the MSC8101 at the rising edge of
PORESET.
0
1
Reset Configuration Master.
Reset Configuration Slave.
DBREQ/ EE0
EONCE Event Bit 0
Input line sampled after SC140 core PLL locks. Holding EE0
high when PORESET is deasserted puts the SC140 into
Debug mode.
0
SC140 starts the normal processing
mode after reset.
SC140 enters Debug mode immediately
after reset.
Host Port Enable
Input line sampled at the rising edge of PORESET. If
asserted, the Host port is enabled, the system data bus is
32-bit wide, and the Host must program the reset
configuration word.
0
1
Host port disabled (hardware reset
configuration enabled).
Host port enabled.
Boot Mode
Input lines sampled at the rising edge of PORESET, which
determine the MSC8101 Boot mode.
00
01
10
11
MSC8101 boots from external memory.
MSC8101 boots from HDI16.
Reserved.
Reserved.
HPE/EE1
BTM[0–1]/
EE[4–5]
Table 2-14.
No.
1
2
3
4
5
Reset Timing
Characteristics
Required external PORESET duration minimum
• CLKIN = 18 MHz
• CLKIN = 75 MHz
Delay from deassertion of external PORESET to deassertion of
internal PORESET
• CLKIN = 18 MHz
• CLKIN = 75 MHz
Delay from deassertion of internal PORESET to SPLL lock
• SPLLMFCLK = 18 MHz
• SPLLMFCLK = 25 MHz
Delay from SPLL lock to DLL lock
• DLL enabled
— BCLK = 18 MHz
— BCLK = 75 MHz
• DLL disabled
1
Expression
Min
Max
Unit
888.8
213.3
—
—
ns
ns
16 / CLKIN
1024 / CLKIN
56.89
13.65
µs
µs
44.4
32.0
µs
µs
170.72
40.97
0.0
µs
µs
ns
199.17
47.5
µs
µs
28.4
6.83
µs
µs
800 / SPLLMFCLK
3073 / BLCK
—
Delay from SPLL lock to HRESET deassertion
• DLL enabled
— BCLK = 18 MHz
— BCLK = 75 MHz
• DLL disabled
— BCLK = 18 MHz
— BCLK = 75 MHz
3585 / BLCK
512 / BLCK
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
2-9
Physical and Electrical Specifications
Table 2-14.
No.
6
Note:
Reset Timing (Continued)
Characteristics
Expression
Delay from SPLL lock to SRESET deassertion
• DLL enabled
— BCLK = 18 MHz
— BCLK = 75 MHz
• DLL disabled
— BCLK = 18 MHz
— BCLK = 75 MHz
Min
Max
3588 / BLCK
Unit
199.33
47.84
µs
µs
28.61
6.87
µs
µs
515 / BLCK
Value given for lowest possible CLKIN frequency 18 MHz to ensure proper initialization of reset sequence.
2.6.3.3 Host Reset Configuration
Host reset configuration allows the host to program the reset configuration word via the Host port after PORESET is
deasserted, as described in the MSC8101 Reference Manual. The MSC8101 samples the signals described in Table
2-13 one the rising edge of PORESET when the signal is deasserted.
If HPE is sampled high, the host port is enabled. In this mode the RSTCONF pin must be pulled up. The device
extends the internal PORESET until the host programs the reset configuration word register. The host must write
four 8-bit half-words to the Host Reset Configuration Register address to program the reset configuration word,
which is 32 bits wide. For more information, see the MSC8101 Reference Manual. The reset configuration word is
programmed before the internal PLL and DLL in the MSC8101 are locked. The host must program it after the
rising edge of the PORESET input. In this mode, the host must have its own clock that does not depend on the
MSC8101 clock. After the PLL and DLL are locked, HRESET remains asserted for another 512 bus clocks and is
then released. The SRESET is released three bus clocks later (see Figure 2-3).
1
PORESET
Input
PORESET
Internal
asserted for
min 16
CLKIN.
RSTCONF, HPE
HRM, BTM
pins are sampled
Any time
HRESET
Output (I/O)
Host programs
Reset Configuration
Word
MODCK[1–3] pins
are sampled.
MODCK_H bits
are ready for PLL.
PLL locked
DLL locked
SRESET
Output (I/O)
2
3
4
PLL locks after
800 SPLLMFCLKs and
DLL locks 3073 BUS clocks
after PLL is locked.
When DLL is disabled,
reset period is shortened
by DLL lock time.
Figure 2-3.
5
6
HRESET/SRESET are
extended for 512/515 BUS
clocks, respectively, from PLL
and DLL lock
Host Reset Configuration Timing
MSC8101 Technical Data, Rev. 16
2-10
Freescale Semiconductor
AC Timings
2.6.3.4 Hardware Reset Configuration
Hardware reset configuration is enabled if HPE is sampled low at the rising edge of PORESET. The value driven on
RSTCONF while PORESET changes from assertion to deassertion determines the MSC8101 configuration. If
RSTCONF is deasserted (driven high) while PORESET changes, the MSC8101 acts as a configuration slave. If
RSTCONF is asserted (driven low) while PORESET changes, the MSC8101 acts as a configuration master. Section
2.6.3.4, Hardware Reset Configuration, explains the configuration sequence and the terms “configuration master”
and “configuration slave.”
Directly after the deassertion of PORESET and choice of the reset operation mode as configuration master or
configuration slave, the MSC8101 starts the configuration process. The MSC8101 asserts HRESET and SRESET
throughout the power-on reset process, including configuration. Configuration takes 1024 CLOCKIN cycles, after
which MODCK[1–3] are sampled to determine the MSC8101’s working mode.
Next, the MSC8101 halts until the SPLL locks. The SPLL locks according to MODCK[1–3], which are sampled, and
to MODCK_H taken from the Reset Configuration Word. SPLL locking time is 800 reference clocks, which is the
clock at the output of the SPLL Pre-divider. After the SPLL is locked, all the clocks to the MSC8101 are enabled.
If the DLLDIS bit in the reset configuration word is reset, the DLL starts the locking process after the SPLL is
locked. During PLL and DLL locking, HRESET and SRESET are asserted. HRESET remains asserted for another 512
BUS clocks and is then released. The SRESET is released three bus clocks later. If the DLLDIS bit in the reset
configuration word is set, the DLL is bypassed and there is no locking process, thus saving the DLL locking time.
Figure 2-4 shows the power-on reset flow.
1
PORESET
Input
PORESET
Internal
asserted for
min 16
CLKIN.
RSTCONF is sampled for
master/slave determination
MODCK[1–3] are sampled.
MODCK_H bits are ready
for PLL.
HRESET
Output (I/O)
PLL locked
SRESET
Output (I/O)
2
3
In reset configuration mode:
reset configuration sequence
occurs in this period.
Figure 2-4.
DLL locked
4
PLL locks after
800 SPLLMFCLKs. DLL
locks 3073 bus clocks after
PLL is locked.
When DLL is disabled, reset
period is shortened by 3073
bus clocks.
5
6
HRESET/SRESET are
extended for 512/515 bus
clocks, respectively, from PLL
and DLL Lock time.
Hardware Reset Configuration Timing
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
2-11
Physical and Electrical Specifications
2.6.4
System Bus Access Timing
2.6.4.1 Core Data Transfers
Generally, all MSC8101 bus and system output signals are driven from the rising edge of the reference clock
(REFCLK), which is DLLIN. Memory controller signals, however, trigger on four points within a DLLIN cycle.
Each cycle is divided by four internal ticks: T1, T2, T3, and T4. T1 always occurs at the rising edge of DLLIN (and
T3 at the falling edge), but the spacing of T2 and T4 depends on the PLL clock ratio selected, as Table 2-15 shows.
Table 2-15.
Tick Spacing for Memory Controller Signals
Tick Spacing (T1 Occurs at the Rising Edge of DLLIN)
PLL Clock Ratio
T2
T3
T4
1:2, 1:3, 1:4, 1:5, 1:6
1/4 DLLIN
1/2 DLLIN
3/4 DLLIN
1:2.5
3/10 DLLIN
1/2 DLLIN
8/10 DLLIN
1:3.5
4/14 DLLIN
1/2 DLLIN
11/14 DLLIN
Figure 2-5 is a graphical representation of Table 2-15.
for 1:2, 1:3, 1:4, 1:5, 1:6
DLLIN
T1
T2
T3
T4
DLLIN
for 1:2.5
T1
T2
T3
T4
for 1:3.5
DLLIN
T1
Figure 2-5.
T2
T3
T4
Internal Tick Spacing for Memory Controller Signals
Note: The UPM machine and GPCM machine outputs change on the internal tick determined by the memory
controller programming; the AC specifications are relative to the internal tick. SDRAM machine outputs
change only on the DLLIN rising edge.
MSC8101 Technical Data, Rev. 16
2-12
Freescale Semiconductor
AC Timings
Table 2-16.
No.
AC Timing for SIU Inputs
Characteristic
Value2
Units
0.5
ns
10
Hold time for all signals after the 50% level of the DLLIN rising edge
11a
ABB/AACK set-up time before the 50% level of the DLLIN rising edge
3.5
ns
11b
DBG/DBB/BR/TC set-up time before the 50% level of the DLLIN rising edge
5.0
ns
11c
ARTRY set-up time before the 50% level of the DLLIN rising edge
4.0
ns
11d
TA set-up time before the 50% level of the DLLIN rising edge
• Pipeline mode
• Non-pipeline mode
3.5
4.0
ns
ns
TEA set-up time before the 50% level of the DLLIN rising edge
• Pipeline mode
• Non-pipeline mode
4.0
3.0
ns
ns
PSDVAL set-up time before the 50% level of the DLLIN rising edge
• Pipeline mode
• Non-pipeline mode
3.5
3.5
ns
ns
11g
TS set-up time before the 50% level of the DLLIN rising edge
5.0
ns
11h
BG set-up time before the 50% level of the DLLIN rising edge
4.5
ns
12
Data bus set-up time before the 50% level of the DLLIN rising edge in Normal
• Pipeline mode
• Non-pipeline mode
2.5
5.0
ns
ns
2.5
8.0
ns
ns
DP set-up time before the 50% level of the DLLIN rising edge
• Pipeline mode
• Non-pipeline mode
4.0
9.0
ns
ns
Address bus set-up time before the 50% level of the DLLIN rising edge
• Extra cycle mode (SIUBCR[EXDD] = 0)
• Non-extra cycle mode (SIUBCR[EXDD] = 1)
5.0
8.0
ns
ns
5.0
5.5
ns
ns
3.0
ns
11e
11f
13
Data bus set-up time before the 50% level of the DLLIN rising edge in ECC and PARITY modes
• Pipeline mode
• Non-pipeline mode
14
15a
15b
Address attributes: TT/TBST/TSIZ/GBL set-up time before the 50% level of the DLLIN rising edge
• Extra cycle mode (SIUBCR[EXDD] = 0)
• Non-extra cycle mode (SIUBCR[EXDD] = 1)
PUPMWAIT/IRQ signals set-up time before the 50% level of the DLLIN rising edge
161
Notes:
1.
2.
The set-up time for these signals is for synchronous operation. Any set-up time can be used for asynchronous operation.
Input specifications are measured from the 50% level of the rising edge of DLLIN to the 50% level of the signal. Timings are
measured at the pin.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
2-13
Physical and Electrical Specifications
Table 2-17.
AC Timing for SIU Outputs
Maximum2
No.
31a
Characteristic
Min.
Units
30 pF
50 pF
TA delay from the 50% level of the DLLIN rising edge
• Pipeline mode
• Non-pipeline mode
1.0
1.0
5.0
4.0
6.5
5.5
ns
ns
TEA delay from the 50% level of the DLLIN rising edge
• Pipeline mode
• Non-pipeline mode
1.0
1.0
3.0
3.5
4.5
5.0
ns
ns
PSDVAL delay from the 50% level of the DLLIN rising edge
• Pipeline mode
• Non-pipeline mode
1.0
1.0
4.0
3.5
5.5
5.0
ns
ns
Address bus delay from the 50% level of the DLLIN rising edge
• Multi master mode (SIUBCR[EBM] = 1)
• Single master mode (SIUBCR[EBM] = 0)
1.0
1.0
6.3
5.5
7.8
7.0
ns
ns
32b
Address attributes: TT/TBST/TSIZ/GBL delay from the 50% level of the DLLIN rising edge
1.0
5.5
7.0
ns
32c
BADDR delay from the 50% level of the DLLIN rising edge
1.0
3.5
5.0
ns
33a
Data bus delay from the 50% level of the DLLIN rising edge
• Pipeline mode
• Non-pipeline mode
1.0
1.0
5.0
6.0
6.5
7.5
ns
ns
DP delay from the 50% level of the DLLIN rising edge
• Pipeline mode
• Non-pipeline mode
1.0
1.0
4.0
6.5
5.5
8.0
ns
ns
Memory controller signals/ALE delay from the 50% level of the DLLIN rising edge
1.0
5.5
7.0
ns
31b
31c
32a
33b
34
35a
DBG/BR/DBB delay from the 50% level of the DLLIN rising edge
1.0
4.0
5.5
ns
35b
AACK/ABB/CS delay from the 50% level of the DLLIN rising edge
1.0
4.5
6.0
ns
35c
BG delay from the 50% level of the DLLIN rising edge
1.0
4.0
5.5
ns
35d
TS delay from the 50% level of the DLLIN rising edge
1.0
3.5
5.0
ns
36
Delay from the 50% level of the DLLIN rising edge for all other signals
1.0
4.5
6.0
ns
Notes:
1.
2.
The maximum bus frequency depends on the mode:
• In 60x-compatible mode connected to another MSC8101 device, the frequency is determined by adding the input and output
longest timing values, which results in a frequency of 75 MHz for 30 pF output capacitance. In multi-master mode when
connected to another MSC8101 device, the frequency is determined by adding the input and output longest timing values,
which results in a frequency of 75 MHz for 30 pF output capacitance.
• Certain bus modes, such as non-extra cycle (EXDD = 1), non-pipelined, and ECC/Parity modes, result in slower bus
frequencies.
• In single-master mode, the frequency depends on the timing of the devices connected to the MSC8101.
Output specifications are measured from the 50% level of the rising edge of DLLIN to the 50% level of the signal. Timings are
measured at the pin.
MSC8101 Technical Data, Rev. 16
2-14
Freescale Semiconductor
AC Timings
DLLIN
10
AACK/ARTRY/TA/TEA/DBG/BG/BR
PSDVAL/ABB/DBB/TS inputs
11
10
12
Data bus inputs—normal mode
10
Data bus inputs—ECC and parity modes
13
DP inputs
14
Address bus/TT[0–4]/TC[0–2]/TBST/TSIZ[0–3]/GBL inputs
15
PUPMWAIT/IRQn input
10
16
31
PSDVAL/TEA/TA outputs
Address bus/TT[0–4]/TC[0–2]/TBST/TSIZ[0–3]/GBL/BADDR[27–31] outputs
Data bus outputs
DP outputs
Memory controller/ALE signals
32
33a
33b
34
35
AACK/ARTRY/ABB/TS/DBG/BG/BR/DBB/CS signals
36
All other normal mode outputs
Figure 2-6.
Bus Signal Timing
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
2-15
Physical and Electrical Specifications
2.6.4.2 DMA Data Transfers
Table 2-18 describes the DMA signal timing.
Table 2-18.
Number
DMA Signals
Characteristic
Minimum
Maximum
Units
6
—
ns
0.5
—
ns
9
—
ns
72
DREQ set-up time before DLLIN falling edge
73
DREQ hold time after DLLIN falling edge
74
DONE set-up time before DLLIN rising edge
75
DONE hold time after DLLIN rising edge
0.5
—
ns
76
DACK/DRACK/DONE delay after DLLIN rising edge
0.5
9
ns
The DREQ signal is synchronized with the falling edge of DLLIN. DONE timing is relative to the rising edge of DLLIN .
To achieve fast response, a synchronized peripheral should assert DREQ according to the timings in Table 2-18.
Figure 2-7 shows synchronous peripheral interaction.
DLLIN
73
72
DREQ
75
74
DONE Input
76
DACK/DONE/DRACK Outputs
Figure 2-7.
2.6.5
HDI16 Signals
Host Interface (HDI16) Timing 1, 2
Table 2-19.
Number
DMA Signals
Characteristics3
4
Expression
Value
Unit
(1.5 × TC) + 5.0
Note 11
ns
TC + 5.0
Note 11
ns
44a
Read data strobe minimum assertion width
HACK read minimum assertion width
44b
Read data strobe minimum deassertion width4
HACK read minimum deassertion width
44c
Read data strobe minimum deassertion width4 after “Last Data Register”
reads5,6, or between two consecutive CVR, ICR, or ISR reads7
HACK minimum deassertion width after “Last Data Register” reads5,6
(2.5 × TC) + 5.0
Note 11
ns
45
Write data strobe minimum assertion width8
HACK write minimum assertion width
(1.5 × TC) + 5.0
Note 11
ns
46
Write data strobe minimum deassertion width8
HACK write minimum deassertion width after ICR, CVR and Data Register
writes5
(2.5 × TC) + 5.0
Note 11
ns
47
Host data input minimum set-up time before write data strobe deassertion8
Host data input minimum set-up time before HACK write deassertion
—
5.0
ns
MSC8101 Technical Data, Rev. 16
2-16
Freescale Semiconductor
AC Timings
Table 2-19.
Host Interface (HDI16) Timing1, 2 (Continued)
Characteristics3
Number
Expression
Value
Unit
deassertion8
48
Host data input minimum hold time after write data strobe
Host data input minimum hold time after HACK write deassertion
—
5.0
ns
49
Read data strobe minimum assertion to output data active from high
impedance4
HACK read minimum assertion to output data active from high impedance
—
5.0
ns
(2.0 × TC) + 5.0
Note 11
ns
—
5.0
ns
4
50
Read data strobe maximum assertion to output data valid
HACK read maximum assertion to output data valid
51
Read data strobe maximum deassertion to output data high impedance4
HACK read maximum deassertion to output data high impedance
52
Output data minimum hold time after read data strobe deassertion4
Output data minimum hold time after HACK read deassertion
—
5.0
ns
53
HCS[1–2] minimum assertion to read data strobe assertion4
—
5.0
ns
54
HCS[1–2] minimum assertion to write data strobe assertion8
55
HCS[1–2] maximum assertion to output data valid
56
57
—
5.0
ns
TC + 5.0
Note 11
ns
HCS[1–2] minimum hold time after data strobe deassertion9
—
0.0
ns
HA[0–3], HRW minimum set-up time before data strobe assertion9
• Read
• Write
—
0
5.0
ns
ns
58
HA[0–3], HRW minimum hold time after data strobe deassertion9
—
5.0
ns
61
Maximum delay from read data strobe deassertion to host request deassertion
for “Last Data Register” read4, 5, 10
(3.5 × TC ) + 5.0
Note 11
ns
62
Maximum delay from write data strobe deassertion to host request deassertion
for “Last Data Register” write5,8,10
(3.0 × TC ) + 5
Note 11
ns
63
Minimum delay from DMA HACK (OAD=0) or Read/Write data strobe(OAD=1)
deassertion to HREQ assertion.
(5.0 × TC) + 5.0
Note 11
ns
Maximum delay from DMA HACK (OAD=0) or Read/Write data strobe(OAD=1)
assertion to HREQ deassertion
(3.5 × TC ) + 5.0
Note 11
ns
64
Notes:
TC = 1/ DSPCLK. At 300 MHz, TC = 3.3 ns
In the timing diagrams below, the controls pins are drawn as active low. The pin polarity is programmable.
VCC = 3.3 V ± 0.3 V; TJ = –40°C to +100 °C, C L = 50 pF
The read data strobe is HRD/HRD in the dual data strobe mode and HDS/HDS in the single data strobe mode.
In 64-bit mode, The “last data register” is the register at address $7, which is the last location to be read or written in data
transfers. This is RX0/TX0 in the little endian mode (HBE = 0), or RX3/TX3 in the big endian mode (HBE = 1).
6. This timing is applicable only if a read from the “last data register” is followed by a read from the RXL, RXM, or RXH registers
without first polling RXDF or HREQ bits, or waiting for the assertion of the HREQ/HREQ signal.
7. This timing is applicable only if two consecutive reads from one of these registers are executed.
8. The write data strobe is HWR in the dual data strobe mode and HDS in the single data strobe mode.
9. The data strobe is host read (HRD/HRD) or host write (HWR/HWR) in the dual data strobe mode and host data strobe
(HDS/HDS) in the single data strobe mode.
10. The host request is HREQ/HREQ in the single host request mode and HRRQ/HRRQ and HTRQ/HTRQ in the double host
request mode. HRRQ/HRRQ is deasserted only when HOTX fifo is empty, HTRQ/HTRQ is deasserted only if HORX fifo is full
(treat as level Host Request).
11. Compute the value using the expression.
1.
2.
3.
4.
5.
Figure 2-8 and Figure 2-9 show HDI16 read signal timing. Figure 2-10 and Figure 2-11 show HDI16 write signal
timing.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
2-17
Physical and Electrical Specifications
HA[0–3]
57
58
56
53
HCS[1–2]
57
58
HRW
44a
HDS
44b
51
55
44c
50
52
49
HD[0–15]
61
HREQ (single host request)
HRRQ (double host request)
Figure 2-8.
Read Timing Diagram, Single Data Strobe
HA[0–3]
57
58
56
53
HCS[1–2]
44a
HRD
44b
51
55
44a
50
52
49
HD[0–15]
61
HREQ (single host request)
HRRQ (double host request)
Figure 2-9.
Read Timing Diagram, Double Data Strobe
MSC8101 Technical Data, Rev. 16
2-18
Freescale Semiconductor
AC Timings
HA[0–3]
57
58
56
54
HCS[1–2]
57
58
HRW
45
HDS
46
47
48
HD[0–15]
62
HREQ (single host request)
HTRQ (double host request)
Figure 2-10.
Write Timing Diagram, Single Data Strobe
HA[0–3]
57
58
56
54
HCS[1–2]
45
HWR
46
48
47
HD[0–15]
62
HREQ (single host request)
HTRQ (double host request)
Figure 2-11.
Write Timing Diagram, Double Data Strobe
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
2-19
Physical and Electrical Specifications
Figure 2-12 shows Host DMA read timing.
HREQ
(Output)
63
64
44a
HACK
44b
RX[0–3]
Read
51
50
49
52
Data
Valid
HD[0–15]
(Output)
Figure 2-12.
Host DMA Read Timing Diagram, HPCR[OAD] = 0
Figure 2-13 shows Host DMA write timing.
HREQ
(Output)
63
64
46
45
HACK
TX[0–3]
Write
47
48
HD[0–15]
(Output)
Figure 2-13.
Data
Valid
Host DMA Write Timing Diagram, HPCR[OAD] = 0
MSC8101 Technical Data, Rev. 16
2-20
Freescale Semiconductor
AC Timings
2.6.6
CPM Timings
Table 2-20.
No.
CPM Input Characteristics
Typical
Unit
FCC input set-up time before low-to-high clock transition
a. internal clock (BRGxO)
b. external clock (serial clock input)
10
5
ns
ns
FCC input hold time after low-to-high clock transition
a. internal clock (BRGxO)
b. external clock (serial clock input)
0
3
ns
ns
SCC/SMC/SPI/I2C input set-up time before low-to-high clock transition
a. internal clock (BRGxO)
b. external clock (serial clock input)
20
5
ns
ns
SCC/SMC/SPI/I2C input hold time after low-to-high clock transition
a. internal clock (BRGxO)
b. external clock (serial clock input)
0
5
ns
ns
20
TDM input set-up time before low-to-high serial clock transition
5
ns
21
TDM input hold time after low-to-high serial transition
5
ns
22
PIO/TIMER/DMA input set-up time before low-to-high serial clock transition
10
ns
23
PIO/TIMER/DMA input hold time after low-to-high serial clock transition
3
ns
Min
Max
Unit
FCC output delay after low-to-high clock transition
a. internal clock (BRGxO)
b. external clock (serial input clock)
0
2
6
18
ns
ns
SCC/SMC/SPI/I2C output delay after low-to-high clock transition
a. internal clock (BRGxO)
b. external clock (serial input clock)
0
0
20
30
ns
ns
40
TDM output delay after low-to-high serial clock transition
5
15
ns
42
PIO/TIMER/DMA output delay after low-to-high serial clock transition
1
14
ns
39
17
18
19
Note:
Characteristic
2
FCC, SCC, SMC, SPI, I C are Non-Multiplexed Serial Interface signals.
Table 2-21.
No.
41
38
Note:
CPM Output Characteristics
Characteristic
FCC, SCC, SMC, SPI,
I2
C are non-multiplexed serial interface signals.
BRGxO
17a
29a
FCC inputs
41a
FCC outputs
Figure 2-14.
FCC Internal Clock Diagram
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
2-21
Physical and Electrical Specifications
Serial input clock
17b
39b
FCC inputs
41b
FCC outputs
Figure 2-15.
FCC External Clock Diagram
BRGxO
19a
18a
SCC/SMC/SPI/I2C inputs
38a
SCC/SMC/SPI/I2C outputs
Figure 2-16.
SCC/SMC/SPI/I2C Internal Clock Diagram
Serial input clock
19b
18b
SCC/SMC/SPI/I2C inputs
38b
SCC/SMCSPI/I2C outputs
Figure 2-17.
SCC/SMC/SPI/I2C External Clock Diagram
Serial input clock
20
21
TDM inputs
40
TDM outputs
Figure 2-18.
TDM Signal Diagram
MSC8101 Technical Data, Rev. 16
2-22
Freescale Semiconductor
AC Timings
DLLIN
23
22
PIO/TIMER/DMA inputs
42
PIO/TIMER/DMA outputs
Figure 2-19.
PIO, Timer, and DMA Signal Diagram
Note: The timing values refer to minimum system timing requirements. Actual implementation requires
conformance to the specific protocol requirements. Refer to Chapter 1 to identify the specific input and
output signals associated with the referenced internal controllers and supported communication protocols.
For example, FCC1 supports ATM/Utopia operation in slave mode, multi-PHY master direct polling
mode, and multi-PHY master multiplexed polling mode and each of these modes supports its own set of
signals; the direction (input or output) of some of the shared signal names depends on the selected mode.
2.6.7
JTAG Signals
Table 2-22.
JTAG Timing
All frequencies
No.
Characteristics
Unit
Min
Max
500
TCK frequency of operation
0.0
40.0
MHz
501
TCK cycle time
25.0
—
ns
502
TCK clock pulse width measured at 1.6 V
12.5
—
ns
503
TCK rise and fall times
0.0
3.0
ns
508
TMS, TDI data set-up time
6.0
—
ns
509
TMS, TDI data hold time
3.0
—
ns
510
TCK low to TDO data valid
0.0
15.0
ns
511
TCK low to TDO high impedance
0.0
20.0
ns
512
TRST assert time
100.0
—
ns
513
TRST set-up time to TCK low
40.0
—
ns
501
TCK
(Input)
VIH
502
502
VM
VM
VIL
503
503
Figure 2-20.
Test Clock Input Timing Diagram
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
2-23
Physical and Electrical Specifications
TCK
(Input)
VIH
V IL
508
TDI
TMS
(Input)
509
Input Data Valid
510
TDO
(Output)
Output Data Valid
511
TDO
(Output)
510
TDO
(Output)
Output Data Valid
Figure 2-21.
Test Access Port Timing Diagram
TCK
(Input)
513
TRST
(Input)
512
Figure 2-22.
TRST Timing Diagram
MSC8101 Technical Data, Rev. 16
2-24
Freescale Semiconductor
3
Packaging
This chapter provides information about the MSC8101 package, including diagrams of the package pinouts and
tables showing how the signals discussed in Chapter 1 are allocated. The MSC8101 is available in a 332-pin
lidded flip chip-plastic ball grid array (FC-PBGA).
3.1 FC-PBGA Package Description
Figure 3-1 and Figure 3-2 show top and bottom views of the FC-PBGA package, including pinouts. Table 3-1 lists
the MSC8101 signals alphabetically by signal name. Connections with multiple names are listed individually by
each name. Signals with programmable polarity are shown both as signals which are asserted low (default) and
high (that is, NAME/NAME). Table 3-2 lists the signals numerically by pin number. Each pin number is listed once
with the various signals that are multiplexed to it. For simplicity, signals with programmable polarity are shown in
this table only with their default name (asserted low).
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
3-1
Packaging
Top View
1
A
B
IRQ1
C THERM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
IRQ5
D1
D4
D7
D11
D17
D22
D27
D32
D37
D42
D46
D51
D55
D60
D62
D63
IRQ3
D0
D3
D6
D10
D16
D21
D26
D31
D36
D41
D45
D50
D54
D59
PWE6
DBG
BADDR
28
B
DP0
IRQ4
D2
D5
D9
D15
D20
D25
D30
D35
D40
D44
D49
D53
D58
D61
DBB
BADDR
29
C
GBL
BADDR D
27
D
EE1
EE0
THERM
2
IRQ2
IRQ6
D8
D14
D19
D24
D29
D34
D39
D43
D48
D52
D57
PWE5
E
EE4
EE3
EE2
VDDH
VDD
VDDH
D13
VDDH
VDD
VDDH
VDDH
VDD
VDDH
D47
VDDH
D56
PSDA
10
F
TDO
EED
EE5
VDD
GND
IRQ7
GND
D18
GND
D28
GND
D38
GND
PSD
WE
GND
VDD
G
PA31
TMS
TRST
TCK
VDDH
GND
D12
GND
D23
GND
D33
GND
PSD
VAL
GND
VDDH
H
PB30
PD31
PC31
PB31
GND
TDI
GND
J
PA29
PD30
PC30
VDD
GND
GND
PA30
K
PA28
PD29
PC29
PB29
VDDH
GND
GND
L
PA27
PB28
PC28
VDD
GND
GND
PC27
M
PB27
PC26
PB26
VDDH
GND
PA26
PA16
N
PC25
PA25
PB25
VDD
PC23
GND
PD17
CLKIN
GND
PC6
TSIZ3
P
PC24
PA24
PB24
PA23
PB20
GND
GND
DLL_IN
GND
PC4
R
PC22
SPARE
1
PA22
PB18
PA19
VDDH
VDDH
VDD
VDDH
T
PB21
PB22
PA20
PA17
PC13
PC14
VCC
SYN1
CLK
OUT
U
PA21
PB19
PD18
PD16
NMI
RST
CONF
GND
SYN1
V
PB23
PD19
PC15
PC12
NMI_ HRESET
OUT
PA18
PA15
2
3
4
5
A
MOD
CK1
PSD
CAS
E
PWE7
MOD
CK2
BCTL0
F
VDDH
TEA
MOD
CK3
POE
G
GND
VDD
BR
ALE
PWE4
H
TA
GND
VDDH
VDDH
PSDA
MUX
PGTA
PWE3
J
GND
PWE2
GND
VDDH
PWE1
PWE0
CS2
K
CS6
GND
GND
VDD
CS1
CS3
BCTL1
L
A21
A26
GND
CS0
CS5
CS7
CS4
M
TT1
TT0
A1
VDDH
VDDH
A28
A30
A31
N
GND
GND
GND
GND
GND
VDD
A23
A27
A29
P
VDDH
VDD
VDDH
VDD
VDDH
VDDH
A15
A19
A24
A25
R
PA12
PC7
PA6
AACK
TS
A3
VDDH
A12
A16
A20
A22
T
PA13
PA10
PA8
TBST
TT2
A4
A8
A11
A17
A18
U
GND
SYN
PA11
PD7
PA7
ABB
BG
TSIZ0
TT3
A2
A6
A9
A13
A14
V
TEST
VCC
SYN
PA14
PA9
PC5
INT
_OUT
TSIZ2
TSIZ1
TT4
A0
A5
A7
A10
6
7
8
9
10
11
12
14
15
16
17
18
01
81
SC
1
PO
SRESET RESET
M
W
BADDR BADDR
31
30
19
SPARE ARTRY
5
13
W
19
Note: Signal names in this figure are the default signals after reset, except for signals C2, C19, D1, D2, D18, E1, F3, H13, H14, and W11 which show the second configuration signal name.
Figure 3-1.
MSC8101 Flip Chip Plastic Ball Grid Array (FC-PBGA), Top View
MSC8101 Technical Data, Rev. 16
3-2
Freescale Semiconductor
FC-PBGA Package Description
Bottom View
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
A
D63
D62
D60
D55
D51
D46
D42
D37
D32
D27
D22
D17
D11
D7
D4
D1
IRQ5
B BADDR
28
DBG
PWE6
D59
D54
D50
D45
D41
D36
D31
D26
D21
D16
D10
D6
D3
D0
IRQ3
C BADDR
29
DBB
D61
D58
D53
D49
D44
D40
D35
D30
D25
D20
D15
D9
D5
D2
IRQ4
DP0
D BADDR
27
GBL
PWE5
D57
D52
D48
D43
D39
D34
D29
D24
D19
D14
D8
IRQ6
IRQ2
THERM
2
EE0
EE1
D
MOD
CK1
PSDA
10
D56
VDDH
D47
VDDH
VDD
VDDH
VDDH
VDD
VDDH
D13
VDDH
VDD
VDDH
EE2
EE3
EE4
E
E
PSD
CAS
1
A
IRQ1
B
THERM C
1
F BCTL0
MOD
CK2
PWE7
VDD
GND
PSD
WE
GND
D38
GND
D28
GND
D18
GND
IRQ7
GND
VDD
EE5
EED
TDO
F
G
POE
MOD
CK3
TEA
VDDH
VDDH
GND
PSD
VAL
GND
D33
GND
D23
GND
D12
GND
VDDH
TCK
TRST
TMS
PA31
G
H
PWE4
ALE
BR
VDD
GND
GND
TDI
GND
PB31
PC31
PD31
PB30
H
J
PWE3
PGTA
PSDA
MUX
VDDH
VDDH
GND
TA
PA30
GND
GND
VDD
PC30
PD30
PA29
J
K
CS2
PWE0
PWE1
VDDH
GND
PWE2
GND
GND
GND
VDDH
PB29
PC29
PD29
PA28
K
L
BCTL1
CS3
CS1
VDD
GND
GND
CS6
PC27
GND
GND
VDD
PC28
PB28
PA27
L
M
CS4
CS7
CS5
CS0
GND
A26
A21
PA16
PA26
GND
VDDH
PB26
PC26
PB27
M
N
A31
A30
A28
VDDH
VDDH
A1
TT0
TT1
TSIZ3
PC6
GND
CLKIN
PD17
GND
PC23
VDD
PB25
PA25
PC25
N
P
A29
A27
A23
VDD
GND
GND
GND
GND
GND
PC4
GND
DLL_IN
GND
GND
PB20
PA23
PB24
PA24
PC24
P
R
A25
A24
A19
A15
VDDH
VDDH
VDD
VDDH
VDD
VDDH
VDDH
VDD
VDDH
VDDH
PA19
PB18
PA22
SPARE
1
PC22
R
T
A22
A20
A16
A12
VDDH
A3
TS
AACK
PA6
PC7
PA12
CLK
OUT
VCC
SYN1
PC14
PC13
PA17
PA20
PB22
PB21
T
U
A18
A17
A11
A8
A4
TT2
TBST
PA8
PA10
PA13
GND
SYN1
RST
CONF
NMI
PD16
PD18
PB19
PA21
U
V
A14
A13
A9
A6
A2
TT3
TSIZ0
BG
ABB
PA7
PD7
PA11
GND
SYN
HRESET
NMI_
OUT
PC12
PC15
PD19
PB23
V
A10
A7
A5
A0
TT4
TSIZ1
TSIZ2
INT
_OUT
PC5
PA9
PA14
VCC
SYN
TEST
PO
RESET
SRESET
PA15
PA18
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
W
19
M
SC
81
01
BADDR BADDR
30
31
ARTRY SPARE
5
W
1
Note: Signal names in this figure are the default signals after reset, except for signals C2, C19, D1, D2, D18, E1, F3, H13, H14, and W11 which show the second configuration signal name.
Figure 3-2.
MSC8101 Flip Chip Plastic Ball Grid Array (FC-PBGA), Bottom Vie
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
3-3
Packaging
Table 3-1.
MSC8101 Signal Listing By Name
Signal Name
Number
A0
W15
A1
N14
A2
V15
A3
T14
A4
U15
A5
W16
A6
V16
A7
W17
A8
U16
A9
V17
A10
W18
A11
U17
A12
T16
A13
V18
A14
V19
A15
R16
A16
T17
A17
U18
A18
U19
A19
R17
A20
T18
A21
M13
A22
T19
A23
P17
A24
R18
A25
R19
A26
M14
A27
P18
A28
N17
A29
P19
A30
N18
A31
N19
AACK
T12
ABB
V11
MSC8101 Technical Data, Rev. 16
3-4
Freescale Semiconductor
FC-PBGA Package Description
Table 3-1.
MSC8101 Signal Listing By Name (Continued)
Signal Name
Number
ALE
H18
ARTRY
U12
BADDR27
D19
BADDR28
B19
BADDR29
C19
BADDR30
H14
BADDR31
H13
BCTL0
F19
BCTL1
L19
BG
V12
BNKSEL0
E18
BNKSEL1
F18
BNKSEL2
G18
BR
H17
BRG1O
H3
BRG1O
V2
BRG2O
J3
BRG2O
N7
BRG3O
K3
BRG4O
L3
BRG5O
L7
BRG6O
M2
BRG7O
N1
BRG8O
P1
BTM0
E1
BTM1
F3
CD for FCC1
N10
CD for FCC2
P10
CD/RENA for SCC1
T6
CD/RENA for SCC2
V4
CLK1
H3
CLK2
J3
CLK3
K3
CLK4
L3
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
3-5
Packaging
Table 3-1.
MSC8101 Signal Listing By Name (Continued)
Signal Name
Number
CLK5
L7
CLK6
M2
CLK7
N1
CLK8
P1
CLK9
N5
CLK10
R1
CLKIN
N8
CLKOUT
T8
COL for FCC1
G1
COL for FCC2
M1
CRS for FCC1
J7
CRS for FCC2
M3
CS0
M16
CS1
L17
CS2
K19
CS3
L18
CS4
M19
CS5
M17
CS6
L13
CS7
M18
CTS for FCC1
T10
CTS for FCC2
W10
CTS/CLSN for SCC1
K3
CTS/CLSN for SCC1
V3
CTS/CLSN for SCC2
L3
CTS/CLSN for SCC2
T5
D0
B3
D1
A3
D2
C4
D3
B4
D4
A4
D5
C5
D6
B5
D7
A5
MSC8101 Technical Data, Rev. 16
3-6
Freescale Semiconductor
FC-PBGA Package Description
Table 3-1.
MSC8101 Signal Listing By Name (Continued)
Signal Name
Number
D8
D6
D9
C6
D10
B6
D11
A6
D12
G7
D13
E7
D14
D7
D15
C7
D16
B7
D17
A7
D18
F8
D19
D8
D20
C8
D21
B8
D22
A8
D23
G9
D24
D9
D25
C9
D26
B9
D27
A9
D28
F10
D29
D10
D30
C10
D31
B10
D32
A10
D33
G11
D34
D11
D35
C11
D36
B11
D37
A11
D38
F12
D39
D12
D40
C12
D41
B12
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
3-7
Packaging
Table 3-1.
MSC8101 Signal Listing By Name (Continued)
Signal Name
Number
D42
A12
D43
D13
D44
C13
D45
B13
D46
A13
D47
E14
D48
D14
D49
C14
D50
B14
D51
A14
D52
D15
D53
C15
D54
B15
D55
A15
D56
E16
D57
D16
D58
C16
D59
B16
D60
A16
D61
C17
D62
A17
D63
A18
DACK1
N5
DACK2
N1
DACK3
D5
DACK4
F6
DBB
C18
DBG
B18
DBREQ
D2
DLLIN
P8
DP0
C2
DP1
B1
DP2
D4
DP3
B2
MSC8101 Technical Data, Rev. 16
3-8
Freescale Semiconductor
FC-PBGA Package Description
Table 3-1.
MSC8101 Signal Listing By Name (Continued)
Signal Name
Number
DP4
C3
DP5
A2
DP6
D5
DP7
F6
DRACK1/DONE1
H2
DRACK2/DONE2
J2
DREQ1
R1
DREQ2
P1
DREQ3
C3
DREQ4
A2
EE0
D2
EE1
D1
EE2
E3
EE3
E2
EE4
E1
EE5
F3
EED
F2
EXT_BG2
B1
EXT_BG3
C3
EXT_BR2
C2
EXT_BR3
B2
EXT_DBG2
D4
EXT_DBG3
A2
EXT1
H3
EXT2
N5
GBL
D18
GND
F11
GND
F13
GND
F15
GND
F5
GND
F7
GND
F9
GND
G10
GND
G12
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
3-9
Packaging
Table 3-1.
MSC8101 Signal Listing By Name (Continued)
Signal Name
Number
GND
G14
GND
G6
GND
G8
GND
H15
GND
H5
GND
H7
GND
J14
GND
J5
GND
J6
GND
K13
GND
K15
GND
K6
GND
K7
GND
L14
GND
L15
GND
L5
GND
L6
GND
M15
GND
M5
GND
N6
GND
N9
GND
P11
GND
P12
GND
P13
GND
P14
GND
P15
GND
P6
GND
P7
GND
P9
GNDSYN
V7
GNDSYN1
U7
H8BIT
B16
HA0
D14
HA1
C14
MSC8101 Technical Data, Rev. 16
3-10
Freescale Semiconductor
FC-PBGA Package Description
Table 3-1.
MSC8101 Signal Listing By Name (Continued)
Signal Name
Number
HA2
B14
HA3
A14
HACK/HACK
E16
HCS1/HCS1
D15
HCS2/HCS2
A16
HD0
A10
HD1
G11
HD2
D11
HD3
C11
HD4
B11
HD5
A11
HD6
F12
HD7
D12
HD8
C12
HD9
B12
HD10
A12
HD11
D13
HD12
C13
HD13
B13
HD14
A13
HD15
E14
HDDS
C16
HDS/HDS
B15
HDSP
D16
HPE
D1
HRD/HRD
C15
HREQ/HREQ
A15
HRESET
V6
HRRQ/HRRQ
E16
HRW
C15
HTRQ/HTRQ
A15
HWR/HWR
B15
INT_OUT
W11
IRQ1
B1
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
3-11
Packaging
Table 3-1.
MSC8101 Signal Listing By Name (Continued)
Signal Name
Number
IRQ1
D18
IRQ2
C19
IRQ2
D4
IRQ2
V11
IRQ3
B2
IRQ3
C18
IRQ3
H14
IRQ4
C3
IRQ5
A2
IRQ5
H13
IRQ6
D5
IRQ7
F6
IRQ7
W11
L1RSYNC for SI1 TDMA1
T11
L1RSYNC for SI2 TDMB2
K4
L1RSYNC for SI2 TDMC2
P3
L1RSYNC for SI2 TDMD2
P5
L1RXD for SI1 TDMA1 Serial
U10
L1RXD for SI2 TDMB2
H1
L1RXD for SI2 TDMC2
M3
L1RXD for SI2 TDMD2
T2
L1RXD0 for SI1 TDMA1 Nibble
U10
L1RXD1 for SI1 TDMA1 Nibble
T2
L1RXD2 for SI1 TDMA1 Nibble
V1
L1RXD3 for SI1 TDMA1 Nibble
P3
L1TSYNC for SI1 TDMA1
V10
L1TSYNC for SI2 TDMB2
L2
L1TSYNC for SI2 TDMC2
N3
L1TSYNC for SI2 TDMD2
T1
L1TXD for SI1 TDMA1 Serial
W9
L1TXD for SI2 TDMB2
H4
L1TXD for SI2 TDMC2
M1
L1TXD for SI2 TDMD2
V1
L1TXD0 for SI1 TDMA1 Nibble
W9
MSC8101 Technical Data, Rev. 16
3-12
Freescale Semiconductor
FC-PBGA Package Description
Table 3-1.
MSC8101 Signal Listing By Name (Continued)
Signal Name
Number
L1TXD1 for SI1 TDMA1 Nibble
P5
L1TXD2 for SI1 TDMA1 Nibble
T1
L1TXD3 for SI1 TDMA1 Nibble
N3
LIST1 for SI1
R1
LIST1 for SI2
T10
LIST2 for SI1
T6
LIST2 for SI2
N10
LIST3 for SI1
V4
LIST3 for SI2
W10
LIST4 for SI1
T5
LIST4 for SI2
P10
MODCK1
E18
MODCK2
F18
MODCK3
G18
MSNUM0
N2
MSNUM1
P2
MSNUM2
U8
MSNUM3
T9
MSNUM4
V8
MSNUM5
U9
NMI
U5
NMI_OUT
V5
PA6
T11
PA7
V10
PA8
U10
PA9
W9
PA10
U9
PA11
V8
PA12
T9
PA13
U8
PA14
W8
PA15
W3
PA16
M7
PA17
T4
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
3-13
Packaging
Table 3-1.
MSC8101 Signal Listing By Name (Continued)
Signal Name
Number
PA18
W2
PA19
R5
PA20
T3
PA21
U1
PA22
R3
PA23
P4
PA24
P2
PA25
N2
PA26
M6
PA27
L1
PA28
K1
PA29
J1
PA30
J7
PA31
G1
PB18
R4
PB19
U2
PB20
P5
PB21
T1
PB22
T2
PB23
V1
PB24
P3
PB25
N3
PB26
M3
PB27
M1
PB28
L2
PB29
K4
PB30
H1
PB31
H4
PBS0
K18
PBS1
K17
PBS2
K14
PBS3
J19
PBS4
H19
PBS5
D17
MSC8101 Technical Data, Rev. 16
3-14
Freescale Semiconductor
FC-PBGA Package Description
Table 3-1.
MSC8101 Signal Listing By Name (Continued)
Signal Name
Number
PBS6
B17
PBS7
F17
PC4
P10
PC5
W10
PC6
N10
PC7
T10
PC12
V4
PC13
T5
PC14
T6
PC15
V3
PC22
R1
PC23
N5
PC24
P1
PC25
N1
PC26
M2
PC27
L7
PC28
L3
PC29
K3
PC30
J3
PC31
H3
PD7
V9
PD16
U4
PD17
N7
PD18
U3
PD19
V2
PD29
K2
PD30
J2
PD31
H2
PGPL0
E17
PGPL1
F14
PGPL2
G19
PGPL3
E19
PGPL4
J18
PGPL5
J17
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
3-15
Packaging
Table 3-1.
MSC8101 Signal Listing By Name (Continued)
Signal Name
Number
PGTA
J18
POE
G19
PORESET
W5
PPBS
J18
PSDA10
E17
PSDAMUX
J17
PSDCAS
E19
PSDDQM0
K18
PSDDQM1
K17
PSDDQM2
K14
PSDDQM3
J19
PSDDQM4
H19
PSDDQM5
D17
PSDDQM6
B17
PSDDQM7
F17
PSDRAS
G19
PSDVAL
G13
PSDWE
F14
PUPMWAIT
J18
PWE0
K18
PWE1
K17
PWE2
K14
PWE3
J19
PWE4
H19
PWE5
D17
PWE6
B17
PWE7
F17
Reserved
A17
Reserved
A18
Reserved
C2
Reserved
C17
Reserved
C19
Reserved
H14
Reserved
H13
MSC8101 Technical Data, Rev. 16
3-16
Freescale Semiconductor
FC-PBGA Package Description
Table 3-1.
MSC8101 Signal Listing By Name (Continued)
Signal Name
Number
RSTCONF
U6
RTS for FCC1
J7
RTS for FCC2
L2
RTS/TENA for SCC1
K2
RTS/TENA for SCC2
L2
RX_DV for FCC1
L1
RX_DV for FCC2
H1
RX_ER for FCC1
M6
RX_ER for FCC2
L2
RXADDR0 for FCC1 UTOPIA 8
T6
RXADDR1 for FCC1 UTOPIA 8
V4
RXADDR2 for FCC1 UTOPIA 8
N10
RXADDR2/RXCLAV1 for FCC1 UTOPIA 8
N10
RXADDR3 for FCC1 UTOPIA 8
K2
RXADDR4 for FCC1 UTOPIA 8
U3
RXCLAV for FCC1 UTOPIA 8
M6
RXCLAV0 for FCC1 UTOPIA 8
M6
RXCLAV2 for FCC1 UTOPIA 8
K2
RXCLAV3 for FCC1 UTOPIA 8
V4
RXD for FCC1 transparent/HDLC serial
T4
RXD for FCC2 transparent/HDLC serial
T1
RXD for SCC1
H2
RXD for SCC2
H4
RXD0 for FCC1 MII/HDLC nibble
T4
RXD0 for FCC1 UTOPIA 8
U9
RXD0 for FCC2 MII/HDLC nibble
T1
RXD1 for FCC1 MII/HDLC nibble
M7
RXD1 for FCC1 UTOPIA 8
V8
RXD1 for FCC2 MII/HDLC nibble
P5
RXD2 for FCC1 MII/HDLC nibble
W3
RXD2 for FCC1 UTOPIA 8
T9
RXD2 for FCC2 MII/HDLC nibble
U2
RXD3 for FCC1 MII/HDLC nibble
W8
RXD3 for FCC1 UTOPIA 8
U8
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
3-17
Packaging
Table 3-1.
MSC8101 Signal Listing By Name (Continued)
Signal Name
Number
RXD3 for FCC2 MII/HDLC nibble
R4
RXD4 for FCC1 UTOPIA 8
W8
RXD5 for FCC1 UTOPIA 8
W3
RXD6 for FCC1 UTOPIA 8
M7
RXD7 for FCC1 UTOPIA 8
T4
RXENB for FCC1
K1
RXPRTY for FCC1 UTOPIA 8
N7
RXSOC for FCC1
L1
SCL
R4
SDA
U2
SMRXD for SMC1
P10
SMRXD for SMC2
U10
SMSYN for SMC1
V9
SMSYN for SMC2
V10
SMTXD for SMC1
W10
SMTXD for SMC2
W9
SMTXD for SMC2
V3
SPARE1
R2
SPARE5
U11
SPICLK
U3
SPIMISO
U4
SPIMOSI
N7
SPISEL
V2
SRESET
W4
TA
J13
TBST
U13
TC0
E18
TC1
F18
TC2
G18
TCK
G4
TDI
H6
TDO
F1
TEA
G17
TEST
W6
MSC8101 Technical Data, Rev. 16
3-18
Freescale Semiconductor
FC-PBGA Package Description
Table 3-1.
MSC8101 Signal Listing By Name (Continued)
Signal Name
Number
TGATE1
H3
TGATE2
L7
THERM1
C1
THERM2
D3
TIN1/TOUT2
L3
TIN2
K3
TIN3/TOUT4
P1
TIN4
N1
TMCLK
M2
TMS
G2
TOUT1
J3
TOUT3
M2
TRST
G3
TS
T13
TSIZ0
V13
TSIZ1
W13
TSIZ2
W12
TSIZ3
N11
TT0
N13
TT1
N12
TT2
U14
TT3
V14
TT4
W14
TX_EN for FCC1 MII
K1
TX_EN for FCC2 MII
K4
TX_ER for FCC1 MII
J1
TX_ER for FCC2 MII
H4
TXADDR0 for FCC1 UTOPIA 8
V3
TXADDR1 for FCC1 UTOPIA 8
T5
TXADDR2 for FCC1 UTOPIA 8
T10
TXADDR2 for FCC1 UTOPIA 8
T10
TXADDR3 for FCC1 UTOPIA 8
V9
TXADDR4 for FCC1 UTOPIA 8
V2
TXCLAV for FCC1 UTOPIA 8
J7
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
3-19
Packaging
Table 3-1.
MSC8101 Signal Listing By Name (Continued)
Signal Name
Number
TXCLAV0 for FCC1 UTOPIA 8
J7
TXCLAV1 for FCC1 UTOPIA 8
T10
TXCLAV2 for FCC1 UTOPIA 8
V9
TXCLAV3 for FCC1 UTOPIA 8
V2
TXD for FCC1 transparent/HDLC serial
W2
TXD for FCC2 transparent/HDLC serial
T2
TXD for SCC1
J2
TXD for SCC2
H1
TXD0 for FCC1 MII/HDLC nibble
W2
TXD0 for FCC1 UTOPIA 8
N2
TXD0 for FCC2 MII/HDLC nibble
T2
TXD1 for FCC1 MII/HDLC nibble
R5
TXD1 for FCC1 UTOPIA 8
P2
TXD1 for FCC2 MII/HDLC nibble
V1
TXD2 for FCC1 MII/HDLC nibble
T3
TXD2 for FCC1 UTOPIA 8
P4
TXD2 for FCC2 MII/HDLC nibble
P3
TXD3 for FCC1 MII/HDLC nibble
U1
TXD3 for FCC1 UTOPIA 8
R3
TXD3 for FCC2 MII/HDLC nibble
N3
TXD4 for FCC1 UTOPIA 8
U1
TXD5 for FCC1 UTOPIA 8
T3
TXD6 for FCC1 UTOPIA 8
R5
TXD7 for FCC1 UTOPIA 8
W2
TXENB for FCC1
G1
TXPRTY for FCC1 UTOPIA 8
U4
TXSOC for FCC1
J1
VCCSYN
W7
VCCSYN1
T7
VDD
E12
VDD
E5
VDD
E9
VDD
F16
VDD
F4
MSC8101 Technical Data, Rev. 16
3-20
Freescale Semiconductor
FC-PBGA Package Description
Table 3-1.
MSC8101 Signal Listing By Name (Continued)
Signal Name
Number
VDD
H16
VDD
J4
VDD
L16
VDD
L4
VDD
N4
VDD
P16
VDD
R11
VDD
R13
VDD
R8
VDDH
E10
VDDH
E11
VDDH
E13
VDDH
E15
VDDH
E4
VDDH
E6
VDDH
E8
VDDH
G15
VDDH
G16
VDDH
G5
VDDH
J15
VDDH
J16
VDDH
K16
VDDH
K5
VDDH
M4
VDDH
N15
VDDH
N16
VDDH
R10
VDDH
R12
VDDH
R14
VDDH
R15
VDDH
R6
VDDH
R7
VDDH
R9
VDDH
T15
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
3-21
Packaging
Table 3-2.
MSC8101 Signal Listing by Pin Designator
Number
Signal Name
A2
IRQ5 / DP5 / DREQ4 / EXT_DBG3
A3
D1
A4
D4
A5
D7
A6
D11
A7
D17
A8
D22
A9
D27
A10
D32 / HD0
A11
D37 / HD5
A12
D42 / HD10
A13
D46 / HD14
A14
D51 / HA3
A15
D55 / HREQ / HTRQ
A16
D60 / HCS2
A17
D62 / Reserved
A18
D63 / Reserved
B1
IRQ1 / DP1 / EXT_BG2
B2
IRQ3 / DP3 / EXT_BR3
B3
D0
B4
D3
B5
D6
B6
D10
B7
D16
B8
D21
B9
D26
B10
D31
B11
D36 / HD4
B12
D41 / HD9
B13
D45 / HD13
B14
D50 / HA2
B15
D54 / HDS / HWR
B16
D59 / H8BIT
B17
PWE6 / PSDDQM6 / PBS6
B18
DBG
B19
BADDR28
C1
THERM1
C2
Reserved / DP0 / EXT_BR2
C3
IRQ4 / DP4 / DREQ3 / EXT_BG3
MSC8101 Technical Data, Rev. 16
3-22
Freescale Semiconductor
FC-PBGA Package Description
Table 3-2.
MSC8101 Signal Listing by Pin Designator (Continued)
Number
Signal Name
C4
D2
C5
D5
C6
D9
C7
D15
C8
D20
C9
D25
C10
D30
C11
D35 / HD3
C12
D40 / HD8
C13
D44 / HD12
C14
D49 / HA1
C15
D53 / HRW / HRD
C16
D58 / HDDS
C17
D61
C18
DBB / IRQ3
C19
BADDR29 / IRQ2
D1
HPE / EE1
D2
DBREQ / EE0
D3
THERM2
D4
IRQ2 / DP2 / EXT_DBG2
D5
IRQ6 / DP6 / DACK3
D6
D8
D7
D14
D8
D19
D9
D24
D10
D29
D11
D34 / HD2
D12
D39 / HD7
D13
D43 / HD11
D14
D48 / HA0
D15
D52 / HCS1
D16
D57 / HDSP
D17
PWE5 / PSDDQM5 / PBS5
D18
IRQ1 / GBL
D19
BADDR27
E1
BTM0 / EE4
E2
EE3
E3
EE2
E4
VDDH
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
3-23
Packaging
Table 3-2.
MSC8101 Signal Listing by Pin Designator (Continued)
Number
Signal Name
E5
VDD
E6
VDDH
E7
D13
E8
VDDH
E9
VDD
E10
VDDH
E11
VDDH
E12
VDD
E13
VDDH
E14
D47 / HD15
E15
VDDH
E16
D56 / HACK / HRRQ
E17
PSDA10 / PGPL0
E18
MODCK1 / TC0 / BNKSEL0
E19
PSDCAS / PGPL3
F1
TDO
F2
EED
F3
BTM1 / EE5
F4
VDD
F5
GND
F6
IRQ7 / DP7 / DACK4
F7
GND
F8
D18
F9
GND
F10
D28
F11
GND
F12
D38 / HD6
F13
GND
F14
PSDWE / PGPL1
F15
GND
F16
VDD
F17
PWE7 / PSDDQM7 / PBS7
F18
MODCK2 / TC1 / BNKSEL1
F19
BCTL0
G1
PA31 / FCC1:UTOPIA8:TXENB / FCC1:MII:COL
G2
TMS
G3
TRST
G4
TCK
G5
VDDH
MSC8101 Technical Data, Rev. 16
3-24
Freescale Semiconductor
FC-PBGA Package Description
Table 3-2.
MSC8101 Signal Listing by Pin Designator (Continued)
Number
Signal Name
G6
GND
G7
D12
G8
GND
G9
D23
G10
GND
G11
D33 / HD1
G12
GND
G13
PSDVAL
G14
GND
G15
VDDH
G16
VDDH
G17
TEA
G18
MODCK3 / TC2 / BNKSEL2
G19
POE / PSDRAS / PGPL2
H1
PB30 / FCC2:MII:RX_DV / SCC2:TXD / TDBM2:L1RXD
H2
PD31 / SCC1:RXD / DRACK1 / DONE1
H3
PC31 / BRG1O / CLK1 / TGATE1
H4
PB31 / FCC2:MII:TX_ER / SCC2:RXD / TDMB2:L1TXD
H5
GND
H6
TDI
H7
GND
H13
Reserved / BADDR31 / IRQ5
H14
Reserved / BADDR30 / IRQ3
H15
GND
H16
VDD
H17
BR
H18
ALE
H19
PWE4 / PSDDQM4 / PBS4
J1
PA29 / FCC1:UTOPIA8:TXSOC / FCC1:MII:TX_ER
J2
PD30 / SCC1:TXD / DMA:DRACK2/DONE2
J3
PC30 / EXT1 / BRG2O / CLK2 / TOUT1
J4
VDD
J5
GND
J6
GND
J7
PA30 / FCC1:UTOPIA8:TXCLAV / FCC1:UTOPIA8:TXCLAV0 / FCC1:MII:CRS /
FCC1:HDLC and transparent:RTS
J13
TA
J14
GND
J15
VDDH
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
3-25
Packaging
Table 3-2.
MSC8101 Signal Listing by Pin Designator (Continued)
Number
Signal Name
J16
VDDH
J17
PSDAMUX / PGPL5
J18
PGTA / PUPMWAIT / PPBS / PGPL4
J19
PWE3 / PSDDQM3 / PBS3
K1
PA28 / FCC1:UTOPIA8:RXENB / FCC1:MII:TX_EN
K2
PD29 / FCC1:UTOPIA8:RXADDR3 / FCC1:UTOPIA8:RXCLAV2 /
SCC1:RTS/TENA
K3
PC29 / SCC1:CTS / SCC1:CLSN / BRG3O / CLK3 / TIN2
K4
PB29 / FCC2:MII:TX_EN / TDMB2:L1RSYNC
K5
VDDH
K6
GND
K7
GND
K13
GND
K14
PWE2 / PSDDQM2 / PBS2
K15
GND
K16
VDDH
K17
PWE1 / PSDDQM1 / PBS1
K18
PWE0 / PSDDQM0 / PBS0
K19
CS2
L1
PA27 / FCC1:UTOPIA8:RXSOC / FCC1:MII:RX_DV
L2
PB28 / FCC2:RX_ER / FCC2:HDLC:RTS / SCC2:RTS/TENA / TDMB2:L1TSYNC
L3
PC28 / SCC2:CTS/CLSN / BRG4O / CLK4 / TIN1/TOUT2
L4
VDD
L5
GND
L6
GND
L7
PC27 / CLK5 / BRG5O / TGATE2
L13
CS6
L14
GND
L15
GND
L16
VDD
L17
CS1
L18
CS3
L19
BCTL1
M1
PB27 / FCC2:MII:COL / TDMC2:L1TXD
M2
PC26 / TMCLK / BRG6O / CLK6 / TOUT3
M3
PB26 / FCC2:MII:CRS / TDMC2:L1RXD
M4
VDDH
M5
GND
M6
PA26 / FCC1:UTOPIA8:RXCLAV / FCC1:UTOPIA8:RXCLAV0 /
FCC1:MII:RX_ER
MSC8101 Technical Data, Rev. 16
3-26
Freescale Semiconductor
FC-PBGA Package Description
Table 3-2.
MSC8101 Signal Listing by Pin Designator (Continued)
Number
Signal Name
M7
PA16 / FCC1:UTOPIA8:RXD6 / FCC1:MII and HDLC nibble:RXD1
M13
A21
M14
A26
M15
GND
M16
CS0
M17
CS5
M18
CS7
M19
CS4
N1
PC25 / DMA:DACK2 / BRG7O / CLK7 / TIN4
N2
PA25 / FCC1:UTOPIA8:TXD0 / SDMA:MSNUM0
N3
PB25 / FCC2:MII and HDLC nibble:TXD3 / TDMA1:nibble:L1TXD3 /
TDMC2:L1TSYNC
N4
VDD
N5
PC23 / EXT2 / DMA:DACK1 / CLK9
N6
GND
N7
PD17 / FCC1:UTOPIA8:RXPRTY / SPI:SPIMOSI / BRG2O
N8
CLKIN
N9
GND
N10
PC6 / FCC1:UTOPIA8:RXADDR2 / FCC1:UTOPIA8:RXADDR2/RXCLAV1 /
FCC1:CD / SI2:LIST2
N11
TSIZ3
N12
TT1
N13
TT0
N14
A1
N15
VDDH
N16
VDDH
N17
A28
N18
A30
N19
A31
P1
PC24 / DMA:DREQ2 / BRG8O / CLK8 / TIN3/TOUT4
P2
PA24 / FCC1:UTOPIA8:TXD1 / SDMA:MSNUM1
P3
PB24 / FCC2:MII and HDLC nibble:TXD2 / TDMA1:nibble:L1RXD3 /
TDMC2:L1RSYNC
P4
PA23 / FCC1:UTOPIA8:TXD2
P5
PB20 / FCC2:MII and HDLC nibble:RXD1 / TDMA1:nibble:L1TXD1 /
TDMD2:L1RSYNC
P6
GND
P7
GND
P8
DLLIN
P9
GND
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
3-27
Packaging
Table 3-2.
MSC8101 Signal Listing by Pin Designator (Continued)
Number
Signal Name
P10
PC4 / FCC2:CD / SMC1:SMRXD / SI2:LIST4
P11
GND
P12
GND
P13
GND
P14
GND
P15
GND
P16
VDD
P17
A23
P18
A27
P19
A29
R1
PC22 / SI1:LIST1 / DREQ1 / CLK10
R2
SPARE1
R3
PA22 / FCC1:UTOPIA8:TXD3
R4
PB18 / FCC2:MII and HDLC nibble:RXD3 / I2C:SCL
R5
PA19 / FCC1:UTOPIA8:TXD6 / FCC1:MII and HDLC nibble:TXD1
R6
VDDH
R7
VDDH
R8
VDD
R9
VDDH
R10
VDDH
R11
VDD
R12
VDDH
R13
VDD
R14
VDDH
R15
VDDH
R16
A15
R17
A19
R18
A24
R19
A25
T1
PB21 / FCC2:MII and HDLC nibble:RXD0 /
FCC2:transparent and HDLC serial:RXD /TDMA1:nibble:L1TXD2 /
TDMD2:L1TSYNC
T2
PB22 / FCC2:MII and HDLC nibble TXD0 /
FCC2:transparent and HDLC serial TXD /TDMA1:nibble L1RXD1 /
TDMD2:L1RXD
T3
PA20 / FCC1:UTOPIA8 TXD5 / FCC1:MII and HDLC nibble TXD2
T4
PA17 / FCC1:UTOPIA8 RXD7 / FCC1:MII and HDLC nibble RXD0 /
FCC1:transparent and HDLC serial RXD
T5
PC13 / FCC1:UTOPIA8:TXADDR1 / SCC2:CTS/CLSN / SI1:LIST4
T6
PC14 / FCC1:UTOPIA8:RXADDR0 / SCC1:CD/RENA / SI1:LIST2
T7
V CCSYN1
MSC8101 Technical Data, Rev. 16
3-28
Freescale Semiconductor
FC-PBGA Package Description
Table 3-2.
MSC8101 Signal Listing by Pin Designator (Continued)
Number
Signal Name
T8
CLKOUT
T9
PA12 / FCC1:UTOPIA8:RXD2 / SDMA:MSNUM3
T10
PC7 / FCC1:UTOPIA8:TXADDR2 /
FCC1:UTOPIA8:TXADDR2/TXCLAV1 / FCC1:CTS / SI1:LIST1
T11
PA6 / TDMA1:L1RSYNC
T12
AACK
T13
TS
T14
A3
T15
VDDH
T16
A12
T17
A16
T18
A20
T19
A22
U1
PA21 / FCC1:TXD4 / FCC1:MII and HDLC nibble TXD3
U2
PB19 / FCC2:MII and HDLC nibble RXD2 / I2C:SDA
U3
PD18 / FCC1:UTOPIA8:RXADDR4 / FCC1:UTOPIA8:RXCLAV3 / SPI:SPICLK
U4
PD16 / FCC1:UTOPIA8:TXPRTY / SPI:SPIMISO
U5
NMI
U6
RSTCONF
U7
GNDSYN1
U8
PA13 / FCC1:UTOPIA8:RXD3 / SDMA:MSNUM2
U9
PA10 / FCC1:UTOPIA8:RXD0 / SDMA:MSNUM5
U10
PA8 / SMC2:SMRXD / TDMA1:serial L1RXD / TDMA1:nibble L1RXD0
U11
SPARE5
U12
ARTRY
U13
TBST
U14
TT2
U15
A4
U16
A8
U17
A11
U18
A17
U19
A18
V1
PB23 / FCC2:MII and HDLC nibble:TXD1 / TDMA1:nibble:L1RXD2 /
TDMD2:L1TXD
V2
PD19 / FCC1:UTOPIA8:TXADDR4 / FCC1:UTOPIA:TXCLAV3 / SPI:SPISEL /
BRG1O
V3
PC15 / FCC1:UTOPIA8:TXADDR0 / SCC1:CTS/CLSN / SMC2:SMTXD
V4
PC12 / FCC1:UTOPIA8:RXADDR1 / SCC2:CD/RENA / SI1:LIST3
V5
NMI_OUT
V6
HRESET
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
3-29
Packaging
Table 3-2.
MSC8101 Signal Listing by Pin Designator (Continued)
Number
Signal Name
V7
GNDSYN
V8
PA11 / FCC1:UTOPIA8:RXD1 / SDMA:MSNUM4
V9
PD7 / FCC1:UTOPIA8:TXADDR3 / FCC1:UTOPIA8:TXCLAV2 / SMC1:SMSYN
V10
PA7 / SMC2:SMSYN / TDMA1:L1TSYNC
V11
ABB / IRQ2
V12
BG
V13
TSIZ0
V14
TT3
V15
A2
V16
A6
V17
A9
V18
A13
V19
A14
W2
PA18 / FCC1:UTOPIA8:TXD7 / FCC1:MII and HDLC nibble:TXD0 /
FCC1:transparent and HDLC serial:TXD
W3
PA15 / FCC1:UTOPIA8:RXD5 / FCC1:MII and HDLC nibble:RXD2
W4
SRESET
W5
PORESET
W6
TEST
W7
VCCSYN
W8
PA14 / FCC1:UTOPIA8 RXD4 / FCC1:MII and HDLC nibble:RXD3
W9
PA9 / SMC2:SMTXD / TDMA1:serial:L1TXD /TDMA1:nibble:L1TXD0
W10
PC5 / FCC2:CTS / SMC1:SMTXD / SI2:LIST3
W11
IRQ7 / INT_OUT
W12
TSIZ2
W13
TSIZ1
W14
TT4
W15
A0
W16
A5
W17
A7
W18
A10
MSC8101 Technical Data, Rev. 16
3-30
Freescale Semiconductor
Lidded FC-PBGA Package Mechanical Drawing
3.2 Lidded FC-PBGA Package Mechanical Drawing
.
Notes:
1. Dimensioning and tolerancing
per ASME Y14.5M–1994.
2. Dimensions in millimeters.
3. Maximum solder ball diameter
measured parallel to Datum A.
4. Primary Datum A and the
seating plane are defined by
the spherical crowns of the
solder balls.
CASE 1473-01
Figure 3-3.
Case 1473-01 Mechanical Information, 332-pin Lidded FC-PBGA Package
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
3-31
Packaging
MSC8101 Technical Data, Rev. 16
3-32
Freescale Semiconductor
4
Design Considerations
This chapter includes design and layout guidelines for manufacturing boards using the MSC8102.
4.1 Thermal Design Considerations
The average chip-junction temperature, TJ, in °C can be obtained from the following:
TJ = TA + (PD •
θJA)
Equation 1
where
TA = ambient temperature °C
θJA = package thermal resistance, junction to ambient, °C/W
PD = PINT + PI/O in W
PINT = IDD × VDD in W—chip internal power
PI/O = power dissipation on output pins in W—user determined
The user should set TA and PD such that TJ does not exceed the maximum operating conditions. In case TJ is too
high, the user should either lower the ambient temperature or the power dissipation of the chip.
4.2 Electrical Design Considerations
The input voltage must not exceed the I/O supply VDDH by more than 2.5 V at any time, including during power-on
reset. In turn, VDDH can exceed VDD/VCCSYN by more than 3.3 V during power-on reset, but for no more than 100 ms.
VDDH should not exceed VDD/VCCSYN by more than 2.1 V during normal operation. VDD/VCCSYN must not exceed VDDH
by more than 0.4 V at any time, including during power-on reset. Therefore the recommendation is to use
“bootstrap” diodes between the power rails, as shown in Figure 4-1.
3.3 V (VDDH)
I/O Power
MUR420
MUR420
MUR420
Core/PLL
Supply
Figure 4-1.
MUR420
1.6 V (VDD/VCCSYN)
Bootstrap Diodes for Power-Up Sequencing
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
4-1
Design Considerations
Select the bootstrap diodes such that a nominal VDD/VCCSYN is sourced from the VDDH power supply until the
VDD/VCCSYN power supply becomes active. In Figure 4-1, four MUR420 Schottky barrier diodes are connected in
series; each has a forward voltage (VF) of 0.6 V at high currents, so these diodes provide a 2.4 V drop, maintaining
0.9 V on the 1.6 V power line. Once the core/PLL power supply stabilizes at 1.6 V, the bootstrap diodes will be
reverse biased with negligible leakage current. The VF should be effective at the current levels required by the
processor. Do not use diodes with a nominal V F that drops too low at high current.
4.3 Power Considerations
The internal power dissipation consists of three components:
PINT = PCORE + PSIU + PCPM
Power dissipation depends on the operating frequency of the different portions of the chip. Table 2-5 provides
typical power values at the specified operating frequencies. To determine the typical power dissipation for a given
set of frequencies, use the following equations:
PCORE (f) = ((PCORE – PLCO)/fCORE) × fCOREA + PLCO
PCPM (f) = ((PCPM – PLCP)/fCPM) × fCPMA + PLCP
PSIU (f) = ((PSIU – PLSI)/fSIU) × fSIUA + PLSI
Where:
fCORE is the core frequency, fSIU is the SIU frequency, and fCPM is the CPM frequency specified in Table 2-5
in MHz
fCOREA is the actual core frequency, FSIUA is the actual SIU frequency, and FCPMA is the actual CPM frequency in MHz
PLCO, PLSI, and PLCP are the leakage power values specified in Table 2-5
All power numbers are in mW
Power consumption is assumed to be linear with frequency. The first part of each equation computes a
mw/MHz value that is then scaled based on the actual frequency used.
To determine a total power dissipation in a specific application, you must add the power values derived from the
above set of equations to the value derived for I/O power consumption using the following equation for each output
pin:
P = C × VDDH2 × f × 10–3
Equation 2
Where: P = power in mW, C = load capacitance in pF, f = output switching frequency in MHz.
For an application in which external data memory is used in a 32-bit single bus mode and no other outputs are
active, the core runs at 200 MHz, the CPM runs at 100 MHz and the SIU runs at 50 MHz, power dissipation is
calculated as follows:
Assumptions:
• External data memory is accessed every second cycle with 10% of address pins switching.
• External data memory writes occurs once every eight cycles with 50% of data pins switching.
• Each address and data pin has a 30 pF total load at the pin.
• The application operates at VDDH = 3.3 V.
MSC8101 Technical Data, Rev. 16
4-2
Freescale Semiconductor
Layout Practices
Since the address pins switch once at every second cycle, the address pins frequency is a quarter of the bus
frequency (that is, 25 MHz).
For the same reason the data pins frequency is 3.125 MHz.
Table 4-1.
Power Dissipation
Pins
Number of Pins
Switching
×C
× VDDH2
× f × 10–3
Power in mW
Address
Data, HRD, HRW
CLKOUT
4
34
1
× 30
× 30
× 30
× 3.32
× 3.32
× 3.32
× 12.5 × 10–3
× 3. 125 × 10–3
× 50 × 10–3
16.25
34.75
16
67
Total PI/O
Calculating internal power (from Table 2-5 values):
PCORE (200) = ((PCORE – PLCO)/300) × 200 + PLCO =((450 – 3) / 300 × 200 + 3 = 301
PCPM (100) = ((PCPM – PLCP) / 200) × 100 + PLCP = ((320 – 6) / 200) × 100 + 6 = 163
PSIU (50) = ((PSIU – PLSI) / 100) × 50 + PLSI = ((80 – 2) / 100) × 50 + 2 = 41
PINT = PCORE(200) + PCPM(100) + PSIU(50) = 301 + 163 + 41 = 505
PD = PINT + PI/O = 505 + 67 = 572
Maximum allowed ambient temperature is:
TA = TJ – (PD × θJA)
4.4 Layout Practices
Each VCC and VDD pin on the MSC8101 should be provided with a low-impedance path to the board’s power supply.
Similarly, each GND pin should be provided with a low-impedance path to ground. The power supply pins drive
distinct groups of logic on the chip. The VCC power supply should be bypassed to ground using at least four 0.1 µF
by-pass capacitors located as closely as possible to the four sides of the package. The capacitor leads and
associated printed circuit traces connecting to chip VCC, VDD, and GND should be kept to less than half an inch per
capacitor lead. A four-layer board is recommended, employing two inner layers as VCC and GND planes.
All output pins on the MSC8101 have fast rise and fall times. Printed circuit board (PCB) trace interconnection
length should be minimized in order to minimize undershoot and reflections caused by these fast output switching
times. This recommendation particularly applies to the address and data busses. Maximum PCB trace lengths of six
inches are recommended. Capacitance calculations should consider all device loads as well as parasitic
capacitances due to the PCB traces. Attention to proper PCB layout and bypassing becomes especially critical in
systems with higher capacitive loads because these loads create higher transient currents in the VCC, VDD, and GND
circuits. Pull up all unused inputs or signals that will be inputs during reset. Special care should be taken to
minimize the noise levels on the PLL supply pins.
There are 2 pairs of PLL supply pins: VCCSYN-GNDSYN and VCCSYN1-GNDSYN1. Each pair supplies one PLL. To
ensure internal clock stability, filter the power to the VCCSYN and VCCSYN1 inputs with a circuit similar to the one in
Figure 0-1.. To filter as much noise as possible, place the circuit as close as possible to VCCSYN and VCCSYN1. The
0.01-µF capacitor should be closest to VCCSYN and VCCSYN1, followed by the 10-µF capacitor, the 10-nH inductor,
and finally the 10-Ω resistor to VDD. These traces should be kept short and direct.
MSC8101 Technical Data, Rev. 16
Freescale Semiconductor
4-3
Design Considerations
GNDSYN and GNDSYN1 should be provided with an extremely low impedance path to ground and should be bypassed
to VCCSYN and VCCSYN1, respectively, by a 0.01-µF capacitor located as close as possible to the chip package. The
user should also bypass GNDSYN and GNDSYN1 to VCCSYN and VCCSYN1 with a 0.01-µF capacitor as closely as
possible to the chip package
VCCSYN
VDD
10Ω
10nH
10 µF
0.01 µF
Figure 0-1. VCCSYN and VCCSYN1 Bypass
MSC8101 Technical Data, Rev. 16
4-4
Freescale Semiconductor
Ordering Information
Consult a Freescale Semiconductor sales office or authorized distributor to determine product availability and
place an order.
Part
MSC8101
Supply
Voltage
1.6 V core
3.3 V I/O
Package Type
Lidded Flip Chip Plastic Ball Grid Array (FCPBGA)
How to Reach Us:
Home Page:
www.freescale.com
E-mail:
[email protected]
USA/Europe or Locations not listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
+1-800-521-6274 or +1-480-768-2130
[email protected]
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GMBH
Technical Information Center
Schatzbogen 7
81829 München, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
[email protected]
Japan:
Freescale Semiconductor Japan Ltd.
Technical Information Center
3-20-1, Minami-Azabu. Minato-ku
Tokyo 106-8573, Japan
0120 191014 or +81-3-3440-3569
[email protected]
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T. Hong Kong
+800 2666 8080
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
[email protected]
MSC8101
Rev. 16
11/2004
Pin
Count
Mask
Set
Core
Frequency
(MHz)
Order Number
332
2K87M
250
MSC8101M1250F
275
MSC8101M1375F
300
MSC8101M1500F
Information in this document is provided solely to enable system and software implementers to
use Freescale Semiconductor products. There are no express or implied copyright licenses
granted hereunder to design or fabricate any integrated circuits or integrated circuits based on
the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to any
products herein. Freescale Semiconductor makes no warranty, representation or guarantee
regarding the suitability of its products for any particular purpose, nor does Freescale
Semiconductor assume any liability arising out of the application or use of any product or
circuit, and specifically disclaims any and all liability, including without limitation consequential
or incidental damages. “Typical” parameters which may be provided in Freescale
Semiconductor data sheets and/or specifications can and do vary in different applications and
actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. Freescale
Semiconductor does not convey any license under its patent rights nor the rights of others.
Freescale Semiconductor products are not designed, intended, or authorized for use as
components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the
Freescale Semiconductor product could create a situation where personal injury or death may
occur. Should Buyer purchase or use Freescale Semiconductor products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Freescale
Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such unintended or
unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent
regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. StarCore
is a trademark of StarCore LLC. All other product or service names are the property of their
respective owners.
© Freescale Semiconductor, Inc. 2001, 2004.