ONSEMI NCL30082A

NCL30082
Dimmable Quasi-Resonant
Primary Side Current-Mode
Controller for LED Lighting
with Thermal Fold-back
The NCL30082 is a PWM current mode controller targeting isolated
flyback and non−isolated constant current topologies. The controller
operates in a quasi−resonant mode to provide high efficiency. Thanks
to a novel control method, the device is able to precisely regulate a
constant LED current from the primary side. This removes the need
for secondary side feedback circuitry, biasing and an optocoupler.
The device is highly integrated with a minimum number of external
components. A robust suite of safety protection is built in to simplify
the design. This device supports analog/digital dimming as well as
thermal current fold−back. While the NCL30082 has integrated fixed
overvoltage protection, the designer has the flexibility to program a
lower OVP level.
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
http://onsemi.com
Micro8
DM SUFFIX
CASE 846A
MARKING DIAGRAM
8
AAx
AYWG
G
1
Quasi−resonant Peak Current−mode Control Operation
Primary Side Sensing (no optocoupler needed)
AAx
= Specific Device Code
Wide VCC Range
x
= C or D
A
= Assembly Location
Source 300 mA / Sink 500 mA Totem Pole Driver with 12 V Gate
Y
=
Year
Clamp
W
= Work Week
Precise LED Constant Current Regulation ±1% Typical
G
= Pb−Free Package
(Note: Microdot may be in either location)
Line Feed−forward for Enhanced Regulation Accuracy
Low LED Current Ripple
250 mV ±2% Guaranteed Voltage Reference for Current Regulation
PIN CONNECTIONS
~ 0.9 Power Factor with Valley Fill Input Stage
1
SD
DIM
Low Start−up Current (13 mA typ.)
ZCD
VIN
Analog or Digital Dimming
CS
VCC
GND
DRV
Thermal Fold−back
Wide Temperature Range of −40 to +125°C
(Top View)
Pb−free, Halide−free MSL1 Product
Robust Protection Features
Typical Applications
♦ Over Voltage / LED Open Circuit Protection
♦ Over Temperature Protection
• Integral LED Bulbs
♦ Secondary Diode Short Protection
• LED Power Driver Supplies
♦ Output Short Circuit Protection
• LED Light Engines
♦ Shorted Current Sense Pin Fault Detection
♦ Latched and Auto−recoverable Versions
♦ Brown−out
♦ VCC Under Voltage Lockout
♦ Thermal Shutdown
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 32 of this data sheet.
© Semiconductor Components Industries, LLC, 2013
April, 2013 − Rev. 0
1
Publication Order Number:
NCL30082/D
NCL30082
.
.
Aux
.
VDIM
1
8
2
7
3
6
4
5
Figure 1. Typical Application Schematic for NCL30082
Table 1. PIN FUNCTION DESCRIPTION
Pin No
Pin Name
Function
Pin Description
1
SD
Thermal Fold−back
and shutdown
Connecting an NTC to this pin allows reducing the output current down to 50%
of its fixed value before stopping the controller. A Zener diode can also be
used to pull−up the pin and stop the controller for adjustable OVP protection
2
ZCD
Zero Crossing Detection
3
CS
Current sense
4
GND
−
5
DRV
Driver output
6
VCC
Supplies the controller
This pin is connected to an external auxiliary voltage.
7
VIN
Input voltage sensing
Brown−Out
This pin observes the HV rail and is used in valley selection. This pin also
monitors and protects for low mains conditions.
8
DIM
Analog / PWM dimming
Connected to the auxiliary winding, this pin detects the core reset event.
This pin monitors the primary peak current
The controller ground
The current capability of the totem pole gate drive (+0.3/−0.5 A) makes it suitable to effectively drive a broad range of power MOSFETs.
This pin is used for analog or PWM dimming control. An analog signal than
can be varied between VDIM(EN) and VDIM100 can be used to vary the current,
or a PWM signal with an amplitude greater than VDIM100.
http://onsemi.com
2
NCL30082
CS_shorted Enable
Over Voltage
Protection
Aux_SCP
Fault
Management
Over Temperature
Protection
SD
Thermal
Foldback
Internal
Thermal
Shutdown
VTF
CS
VCC
Clamp
Circuit
Valley Selection
S
Aux_SCP
offset_OK
Leading
Edge
Blanking
VCC Over Voltage
Protection
offset_OK
Aux. Winding
Short Circuit Prot.
Line
Feedforward
Latch
VVIN VREF
Zero Crossing Detection
VVIN
VCC
VCC Management
WOD_SCP
BO_NOK
Qdrv
ZCD
OFF
UVLO
VCC_max
Ipkmax
VREF
VDD
STOP
Q
DRV
Qdrv
VVLY
R
VTF
STOP VREF
CS_reset
Constant−Current
Control
Dimming
Type
Detection
VDIMA
DIM
Ipkmax STOP
Enable
Enable VDIMA
Max. Peak
Current
Limit
VVIN
GND
VVIN
Ipkmax
CS Short
Protection
BO_NOK
CS_shorted
Winding and
Output diode
Short Circuit
Protection
WOD_SCP
Note: CS Short Protection is disabled
Note: for NCL30082B1
Figure 2. Internal Circuit Architecture
http://onsemi.com
3
Brown−Out
VIN
NCL30082
Table 2. MAXIMUM RATINGS TABLE
Symbol
Rating
Value
Unit
VCC(MAX)
ICC(MAX)
Maximum Power Supply voltage, VCC pin, continuous voltage
Maximum current for VCC pin
−0.3, +35
Internally limited
V
mA
VDRV(MAX)
IDRV(MAX)
Maximum driver pin voltage, DRV pin, continuous voltage
Maximum current for DRV pin
−0.3, VDRV (Note 1)
−500, +800
V
mA
VMAX
IMAX
Maximum voltage on low power pins (except pins ZCD, DIM, DRV and VCC)
Current range for low power pins (except pins ZCD, DRV and VCC)
−0.3, +5.5
−2, +5
V
mA
VZCD(MAX)
IZCD(MAX)
Maximum voltage for ZCD pin
Maximum current for ZCD pin
−0.3, +10
−2, +5
V
mA
VDIM(MAX)
Maximum voltage for DIM pin
−0.3, +10
V
RθJ−A
Thermal Resistance, Junction−to−Air
289
°C/W
TJ(MAX)
Maximum Junction Temperature
150
°C
Operating Temperature Range
−40 to +125
°C
Storage Temperature Range
−60 to +150
°C
ESD Capability, HBM model (Note 2)
4
kV
ESD Capability, MM model (Note 2)
200
V
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. VDRV is the DRV clamp voltage VDRV(high) when VCC is higher than VDRV(high). VDRV is VCC unless otherwise noted.
2. This device series contains ESD protection and exceeds the following tests: Human Body Model 4000 V per Mil−Std−883, Method 3015.
3. This device contains latch−up protection and exceeds 100 mA per JEDEC Standard JESD78 except for VIN pin which passes 60 mA.
http://onsemi.com
4
NCL30082
Table 3. ELECTRICAL CHARACTERISTICS (Unless otherwise noted: For typical values TJ = 25°C, VCC = 12 V;
For min/max values TJ = −40°C to +125°C, Max TJ = 150°C, VCC = 12 V)
Description
Test Condition
Symbol
Min
Typ
Max
Unit
VCC increasing
VCC decreasing
VCC decreasing
VCC(on)
VCC(off)
VCC(HYS)
VCC(reset)
16
8.2
8
3.5
18
8.8
–
4.5
20
9.4
–
5.5
Over Voltage Protection
VCC OVP threshold
VCC(OVP)
26
28
30
V
VCC(off) noise filter
VCC(reset) noise filter−
tVCC(off)
tVCC(reset)
–
–
5
20
–
–
ms
ICC(start)
–
13
30
mA
ICC(sFault)
–
46
60
mA
ICC1
ICC2
ICC3
0.8
–
–
1.2
2.3
2.7
1.4
4.0
5.0
Maximum Internal current limit
VILIM
0.95
1
1.05
V
Leading Edge Blanking Duration for VILIM
(Tj = −25°C to 125°C)
tLEB
250
300
350
ns
Leading Edge Blanking Duration for VILIM
(Tj = −40°C to 125°C)
tLEB
240
300
350
ns
Ibias
–
0.02
–
mA
tILIM
–
50
150
ns
VCS(stop)
1.35
1.5
1.65
V
tBCS
–
120
–
ns
Blanking time for CS to GND short detection VpinVIN = 1 V
tCS(blank1)
6
–
12
ms
Blanking time for CS to GND short detection VpinVIN = 3.3 V
tCS(blank2)
2
–
4
ms
Drive Resistance
DRV Sink
DRV Source
RSNK
RSRC
–
–
13
30
–
–
Drive current capability
DRV Sink (Note 4)
DRV Source (Note 4)
ISNK
ISRC
–
–
500
300
–
–
STARTUP AND SUPPLY CIRCUITS
Supply Voltage
Startup Threshold
Minimum Operating Voltage
Hysteresis VCC(on) – VCC(off)
Internal logic reset
V
Startup current
Startup current in fault mode
Supply Current
Device Disabled/Fault
Device Enabled/No output load on pin 5
Device Switching (Fsw = 65 kHz)
mA
VCC > VCC(off)
Fsw = 65 kHz
CDRV = 470 pF,
Fsw = 65 kHz
CURRENT SENSE
Input Bias Current
DRV high
Propagation delay from current detection to gate off−state
Threshold for immediate fault protection activation
Leading Edge Blanking Duration for VCS(stop)
GATE DRIVE
W
mA
Rise Time (10% to 90%)
CDRV = 470 pF
tr
–
40
–
ns
Fall Time (90% to 10%)
CDRV = 470 pF
tf
–
30
–
ns
DRV Low Voltage
VCC = VCC(off)+0.2 V
CDRV = 470 pF,
RDRV = 33 kW
VDRV(low)
8
–
–
V
DRV High Voltage
VCC = 30 V
CDRV = 470 pF,
RDRV = 33 kW
VDRV(high)
10
12
14
V
4. Guaranteed by design
5. OTP triggers when RNTC = 4.7 kW
http://onsemi.com
5
NCL30082
Table 3. ELECTRICAL CHARACTERISTICS (Unless otherwise noted: For typical values TJ = 25°C, VCC = 12 V;
For min/max values TJ = −40°C to +125°C, Max TJ = 150°C, VCC = 12 V)
Description
Test Condition
Symbol
Min
Typ
Max
Unit
ZCD threshold voltage
VZCD increasing
VZCD(THI)
25
45
65
mV
ZCD threshold voltage (Note 4)
VZCD decreasing
VZCD(THD)
5
25
45
mV
ZCD hysteresis (Note 4)
VZCD increasing
VZCD(HYS)
10
–
–
mV
VZCD(short)
0.8
1
1.2
V
tOVLD
70
90
110
ms
trecovery
3
4
5
s
Ipin1 = 3.0 mA
Ipin1 = −2.0 mA
VCH
VCL
–
−0.9
9.5
−0.6
–
−0.3
VZCD decreasing
tDEM
–
–
150
ns
tPAR
–
20
–
ns
tBLANK
2.25
3
3.75
ms
tTIMO
5
6.5
8
ms
Reference Voltage at Tj = 25°C
VREF
245
250
255
mV
Reference Voltage Tj = −40°C to 125°C
VREF
242.5
250
257.5
mV
50% reference voltage (for thermal foldback)
VREF50
–
125
–
mV
Current sense lower threshold for detection of the
leakage inductance reset time
VCS(low)
30
55
80
mV
KLFF
15
17
19
mA/V
VpinVIN = 4.5 V
Ioffset(MAX)
67.5
76.5
85.5
mA
VREF value below which the offset current source is turned off
VREF decreases
VREF(off)
–
37.5
–
mV
VREF value above which the offset current source is turned on
VREF increases
VREF(on)
–
50
–
mV
Threshold for line range detection Vin increasing
(1st to 2nd valley transition for VREF > 0.75 V)
VVIN increases
VHL
2.28
2.4
2.52
V
Threshold for line range detection Vin decreasing
(2nd to 1st valley transition for VREF > 0.75 V)
VVIN decreases
VLL
2.18
2.3
2.42
V
tHL(blank)
15
25
35
ZERO VOLTAGE DETECTION CIRCUIT
Threshold voltage for output short circuit or aux. winding
short circuit detection
Short circuit detection Timer
VZCD < VZCD(short)
Auto−recovery timer duration
Input clamp voltage
High state
Low state
Propagation Delay from valley detection to DRV high
Equivalent time constant for ZCD input (Note 4)
Blanking delay after on−time
Timeout after last demag transition
V
CONSTANT CURRENT CONTROL
LINE FEED−FORWARD
VVIN to ICS(offset) conversion ratio
Offset current maximum value
VALLEY SELECTION
Blanking time for line range detection
Valley thresholds
1st to 2nd valley transition at LL and 2nd to 3rd valley HL
2nd to 1st valley transition at LL and 3rd to 2nd valley HL
2nd to 4th valley transition at LL and 3rd to 5th valley HL
4th to 2nd valley transition at LL and 5th to 3rd valley HL
4th to 7th valley transition at LL and 5th to 8th valley HL
7th to 4th valley transition at LL and 8th to 5th valley HL
7th to 11th valley transition at LL and 8th to 12th valley HL
11th to 7th valley transition at LL and 12th to 8th valley HL
11th to 13th valley transition at LL and 12th to 15th valley HL
13th to 11th valley transition at LL and 15th to 12th valley HL
ms
mV
VREF decreases
VREF increases
VREF decreases
VREF increases
VREF decreases
VREF increases
VREF decreases
VREF increases
VREF decreases
VREF increases
4. Guaranteed by design
5. OTP triggers when RNTC = 4.7 kW
http://onsemi.com
6
VVLY1−2/2−3
VVLY2−1/3−2
VVLY2−4/3−5
VVLY4−2/5−3
VVLY4−7/5−8
VVLY7−4/8−5
VVLY7−11/8−12
VVLY11−7/12−8
VVLY11−13/12−15
VVLY13−11/15−12
177.5
185.0
117.5
125.0
–
–
–
–
–
–
187.5
195.0
125.0
132.5
75.0
82.5
37.5
50.0
15.0
20.0
197.5
205.0
132.5
140.0
–
–
–
–
–
–
NCL30082
Table 3. ELECTRICAL CHARACTERISTICS (Unless otherwise noted: For typical values TJ = 25°C, VCC = 12 V;
For min/max values TJ = −40°C to +125°C, Max TJ = 150°C, VCC = 12 V)
Description
Test Condition
Symbol
Min
Typ
Max
Unit
DIM pin voltage for zero output current (OFF voltage)
VDIM(EN)
0.66
0.7
0.74
V
DIM pin voltage for maximum output current
VDIM100
2.25
2.45
2.65
V
Dimming range
VDIM(range)
–
1.75
–
V
Clamping voltage for DIM pin
VDIM(CLP)
–
7.8
–
V
Dimming pin pull−up current source
IDIM(pullup)
–
280
–
nA
SD pin voltage at which thermal fold−back starts
VTF(start)
0.9
1
1.2
V
SD pin voltage at which thermal fold−back stops
(Iout = 50% Iout(nom))
VTF(stop)
0.64
0.68
0.72
V
Reference current for direct connection of an NTC (Note 5)
IOTP(REF)
80
85
90
mA
DIMMING SECTION
THERMAL FOLD−BACK AND OVP
Fault detection level for OTP (Note 5)
VSD decreasing
VOTP(off)
0.47
0.5
0.53
V
SD pin level at which controller re−start switching after OTP
detection
VSD increasing
VOTP(on)
0.64
0.68
0.72
V
tOTP(start)
180
–
300
ms
Timer duration after which the controller is allowed to start
pulsing (Note 5)
Clamped voltage (SD pin left open)
SD pin open
Clamp series resistor
SD pin detection level for OVP
VSD increasing
Delay before OVP or OTP confirmation (OVP and OTP)
VSD(clamp)
1.13
1.35
1.57
V
RSD(clamp)
–
1.6
–
kW
VOVP
2.35
2.5
2.65
V
TSD(delay)
15
30
45
ms
TSHDN
130
150
170
°C
TSHDN(HYS)
–
50
–
°C
VBO(on)
0.90
1
1.10
V
THERMAL SHUTDOWN
Thermal Shutdown (Note 4)
Device switching
(FSW around 65 kHz)
Thermal Shutdown Hysteresis (Note 4)
BROWN−OUT
Brown−Out ON level (IC start pulsing)
VSD increasing
Brown−Out OFF level (IC shuts down)
VSD decreasing
VBO(off)
0.85
0.9
0.95
V
BO comparators delay
tBO(delay)
–
30
–
ms
Brown−Out blanking time
tBO(blank)
35
50
65
ms
Brown−out pin bias current
IBO(bias)
−250
–
250
nA
4. Guaranteed by design
5. OTP triggers when RNTC = 4.7 kW
http://onsemi.com
7
NCL30082
TYPICAL CHARACTERISTICS
8.90
18.15
8.85
18.10
8.80
VCC(off) (V)
VCC(on) (V)
18.20
18.05
8.75
18.00
8.70
17.95
8.65
17.90
−40
−20
0
20
40
60
80
100
8.60
−40
120
−20
0
20
40
60
80
100
120
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 3. VCC(on) vs. Junction Temperature
Figure 4. VCC(off) vs. Junction Temperature
27.80
18
17
27.75
16
VCC(OVP) (V)
ICC(start) (mA)
27.70
27.65
27.60
15
14
13
12
27.55
11
27.50
−40
−20
0
20
40
60
80
100
10
−40
120
0
20
40
60
80
100
120
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 5. VCC(OVP) vs. Junction Temperature
Figure 6. ICC(start) vs. Junction Temperature
52
1.30
1.28
50
1.26
1.24
48
ICC1 (mA)
ICC(sFault) (mA)
−20
46
44
1.22
1.20
1.18
1.16
42
1.14
40
−40
−20
0
20
40
60
80
100
1.12
−40
120
−20
0
20
40
60
80
100
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 7. ICC(sFault) vs. Junction Temperature
Figure 8. ICC1 vs. Junction Temperature
http://onsemi.com
8
120
NCL30082
TYPICAL CHARACTERISTICS
2.40
2.85
2.80
2.35
2.75
ICC3 (mA)
ICC2 (mA)
2.30
2.25
2.20
2.70
2.65
2.60
2.55
2.15
2.10
−40
2.50
−20
0
20
40
60
80
100
2.45
−40
120
0
20
40
60
80
100
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 9. ICC2 vs. Junction Temperature
Figure 10. ICC3 vs. Junction Temperature
1.495
0.995
1.490
120
VILIM (V)
VCS(stop) (V)
1.000
0.990
1.485
0.985
0.980
−40
−20
1.480
−20
0
20
40
60
80
100
1.475
−40
120
−20
0
20
40
60
80
100
120
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 11. VILIM vs. Junction Temperature
Figure 12. VCS(stop) vs. Junction Temperature
305
1.010
303
1.005
301
VZCD(short) (V)
tLEB (ns)
299
297
295
293
291
289
287
285
−40
1.000
0.995
0.990
0.985
−20
0
20
40
60
80
100
0.980
−40
120
−20
0
20
40
60
80
100
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 13. tLEB vs. Junction Temperature
Figure 14. VZCD(short) vs. Junction
Temperature
http://onsemi.com
9
120
NCL30082
TYPICAL CHARACTERISTICS
7.1
3.20
7.0
6.9
tTIMO (ms)
tBLANK (ms)
3.15
3.10
6.8
6.7
3.05
6.6
−20
0
20
40
60
80
100
6.5
−40
120
0
20
40
60
80
100
TJ, JUNCTION TEMPERATURE (°C)
Figure 15. tBLANK vs. Junction Temperature
Figure 16. tTIMO vs. Junction Temperature
255
55.0
254
54.5
253
54.0
252
251
250
249
−40
53.5
53.0
−20
0
20
40
60
80
100
52.0
−40
120
−20
0
20
40
60
80
100
120
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 17. VREF vs. Junction Temperature
Figure 18. VCS(low) vs. Junction Temperature
16.60
37.6
16.55
37.5
16.50
37.4
16.45
16.40
16.35
16.30
−40
120
52.5
VREF(off) (mV)
KLFF (mA/V)
−20
TJ, JUNCTION TEMPERATURE (°C)
VCS(low) (mV)
VREF (mV)
3.00
−40
37.3
37.2
37.1
−20
0
20
40
60
80
100
37.0
−40
120
−20
0
20
40
60
80
100
120
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 19. KLFF vs. Junction Temperature
Figure 20. VREF(off) vs. Junction Temperature
http://onsemi.com
10
NCL30082
TYPICAL CHARACTERISTICS
49.0
2.400
48.5
2.395
47.5
2.390
47.0
VHL (V)
VREF(on) (mV)
48.0
46.5
46.0
2.385
2.380
45.5
45.0
2.375
44.5
44.0
−40
−20
0
20
40
60
80
100
2.370
−40
120
−20
0
20
40
60
80
100
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 21. VREF(on) vs. Junction Temperature
Figure 22. VHL vs. Junction Temperature
2.300
120
28.0
2.295
27.5
tHL(BLANK) (ms)
VLL (V)
2.290
2.285
2.280
27.0
26.5
2.275
2.270
−40
−20
0
20
40
60
80
100
26.0
−40
120
0
20
40
60
80
100
120
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 23. VLL vs. Junction Temperature
Figure 24. tHL(BLANK) vs. Junction Temperature
186.5
197
VVLY2−1/3−2 (mV)
198
VVLY1−2/2−3 (mV)
187.0
186.0
185.5
185.0
184.5
184.0
−40
−20
196
195
194
193
192
−20
0
20
40
60
80
100
191
−40
120
−20
0
20
40
60
80
100
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 25. VVLY1−2/2−3 vs. Junction
Temperature
Figure 26. VVLY2−1/3−2 vs. Junction
Temperature
http://onsemi.com
11
120
NCL30082
TYPICAL CHARACTERISTICS
124.5
135
VVLY4−2/5−3 (mV)
136
VVLY2−4/3−5 (mV)
125.0
124.0
123.5
123.0
122.5
−20
0
20
40
60
80
100
132
130
−40
120
20
40
60
80
100
Figure 27. VVLY2−4/3−5 vs. Junction
Temperature
Figure 28. VVLY4−2/5−3 vs. Junction
Temperature
87
75.5
86
75.0
74.5
74.0
120
85
84
83
82
81
−20
0
20
40
60
80
100
80
−40
120
−20
0
20
40
60
80
100
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 29. VVLY4−7/5−8 vs. Junction
Temperature
Figure 30. VVLY7−4/8−5 vs. Junction
Temperature
50
37.6
49
37.5
48
VVLY11−7/12−8 (mV)
37.7
37.4
37.3
37.2
120
47
46
45
44
37.1
37.0
−40
0
TJ, JUNCTION TEMPERATURE (°C)
76.0
73.0
−40
−20
TJ, JUNCTION TEMPERATURE (°C)
73.5
VVLY7−11/8−12 (mV)
133
131
VVLY7−4/8−5 (mV)
VVLY4−7/5−8 (mV)
122.0
−40
134
−20
0
20
40
60
80
100
43
−40
120
−20
0
20
40
60
80
100
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 31. VVLY7−11/8−12 vs. Junction
Temperature
Figure 32. VVLY11−7/12−8 vs. Junction
Temperature
http://onsemi.com
12
120
NCL30082
TYPICAL CHARACTERISTICS
15.05
20.5
15.00
20.0
VVLY13−11/15−12 (mV)
21.0
VVLY11−13/12−15 (mV)
15.10
14.95
14.90
14.85
14.80
19.0
18.5
18.0
17.5
14.75
14.70
−40
−20
0
20
40
60
80
100
17.0
−40
120
−20
0
20
40
60
80
100
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 33. VVLY11−13/12−15 vs. Junction
Temperature
Figure 34. VVLY13−11/15−12 vs. Junction
Temperature
0.710
2.46
0.705
2.45
VDIM(100) (V)
VDIM(EN) (V)
19.5
0.700
0.695
120
2.44
2.43
0.690
−40
−20
0
20
40
60
80
100
2.42
−40
120
−20
0
20
40
60
80
100
120
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 35. VDIM(EN) vs. Junction Temperature
Figure 36. VDIM(100) vs. Junction Temperature
88.0
4.55
87.5
4.50
86.5
trecovery (s)
tOVLD (ms)
87.0
86.0
85.5
85.0
4.45
4.40
4.35
84.5
84.0
−40
−20
0
20
40
60
80
100
4.30
−40
120
−20
0
20
40
60
80
100
120
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 37. tOVLD vs. Junction Temperature
Figure 38. trecovery vs. Junction Temperature
http://onsemi.com
13
NCL30082
TYPICAL CHARACTERISTICS
2.500
86.5
2.495
86.0
85.5
VOVP (V)
IOTP(ref) (mA)
2.490
2.485
2.480
85.0
84.5
84.0
2.475
83.5
2.470
−40
−20
0
20
40
60
80
100
83.0
−40
120
−20
0
20
40
60
80
100
120
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 39. VOVP vs. Junction Temperature
Figure 40. IOTP(ref) vs. Junction Temperature
0.690
0.997
0.995
VTF(start) (V)
VOTP(on), VTF(stop) (V)
0.688
0.686
0.684
0.991
0.989
0.682
0.987
0.680
−40
−20
0
20
40
60
80
100
0.985
−40
120
−20
0
20
40
60
80
100
120
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 41. VOTP(on), VTF(stop) vs. Junction
Temperature
Figure 42. VTF(start) vs. Junction Temperature
0.994
0.906
0.992
0.904
0.990
VBO(off) (V)
VBO(on) (V)
0.993
0.902
0.988
0.900
0.986
0.898
0.984
0.982
−40
−20
0
20
40
60
80
100
0.896
−40
120
−20
0
20
40
60
80
100
120
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 43. VBO(on) vs. Junction Temperature
Figure 44. VBO(off) vs. Junction Temperature
http://onsemi.com
14
NCL30082
TYPICAL CHARACTERISTICS
56.0
tBO(BLANK) (ms)
55.5
55.0
54.5
54.0
53.5
53.0
52.5
−40
−20
0
20
40
60
80
100
120
TJ, JUNCTION TEMPERATURE (°C)
Figure 45. tBO(BLANK) vs. Junction Temperature
APPLICATION INFORMATION
The NCL30082 implements a current−mode architecture
operating in quasi−resonant mode. Thanks to proprietary
circuitry, the controller is able to accurately regulate the
secondary side current of the flyback converter without
using any opto−coupler or measuring directly the secondary
side current.
• Quasi−Resonance Current−Mode Operation:
implementing quasi−resonance operation in peak
current−mode control, the NCL30082 optimizes the
efficiency by switching in the valley of the MOSFET
drain−source voltage. Thanks to a smart control
algorithm, the controller locks−out in a selected valley
and remains locked until the input voltage or the output
current set point significantly changes.
• Primary Side Constant Current Control: thanks to a
proprietary circuit, the controller is able to compensate
for the leakage inductance of the transformer and allow
accurate control of the secondary side current.
• Line Feed−forward: compensation for possible
variation of the output current caused by system slew
rate variation.
• Open LED protection: if the voltage on the VCC pin
exceeds an internal limit, the controller shuts down and
waits 4 seconds before restarting switching.
• Thermal Fold−back / Over Temperature / Over
Voltage Protection: by combining a dual threshold on
the SD pin, the controller allows the direct connection
of an NTC to ground plus a Zener diode to a monitored
voltage. The temperature is monitored and the output
current is linearly reduced in the event that the
•
•
•
•
•
temperature exceeds a prescribed level. If the
temperature continues to increase, the current will be
further reduced until the controller is stopped. The
control will automatically restart if the temperature is
reduced. This pin can implement a programmable OVP
shutdown that can also auto−restart the device.
Brown−Out: the controller includes a brown−out
circuit which safely stops the controller in case the
input voltage is too low. The device will automatically
restart if the line recovers.
Cycle−by−cycle peak current limit: when the current
sense voltage exceeds the internal threshold VILIM, the
MOSFET is turned off for the rest of the switching
cycle.
Winding Short−Circuit Protection: an additional
comparator with a short LEB filter (tBCS) senses the CS
signal and stops the controller if VCS reaches 1.5 x
VILIM. For noise immunity reasons, this comparator is
enabled only during the main LEB duration tLEB.
Output Short−circuit protection: If a very low
voltage is applied on ZCD pin for 90 ms (nominal), the
controllers assume that the output or the ZCD pin is
shorted to ground and enters shutdown. The
auto−restart version (B suffix) waits 4 seconds, then the
controller restarts switching. In the latched version (A
suffix), the controller is latched as long as VCC stays
above the VCC(reset) threshold.
Linear or PWM dimming: the DIM pin allows
implementing both analog and PWM dimming.
http://onsemi.com
15
NCL30082
Constant Current Control
Figure 47 portrays the primary and secondary current of
a flyback converter in discontinuous conduction mode
(DCM). Figure 46 shows the basic circuit of a flyback
converter.
Transformer
Vbulk
Lleak
Cclp
Nsp
Rclp
Vout
.
Lp
.
Clamping
network
DRV
Clump
Rsense
Figure 46. Basic Flyback Converter Schematic
During the on−time of the MOSFET, the bulk voltage
Vbulk is applied to the magnetizing and leakage inductors Lp
and Lleak and the current ramps up.
When the MOSFET is turned−off, the inductor current
first charges Clump. The output diode is off until the voltage
across Lp reverses and reaches:
N spǒV out ) V fǓ
When the diode conducts, the secondary current decreases
linearly from ID,pk to zero. When the diode current has
turned off, the drain voltage begins to oscillate because of
the resonating network formed by the inductors (Lp+Lleak)
and the lump capacitor. This voltage is reflected on the
auxiliary winding wired in flyback mode. Thus, by looking
at the auxiliary winding voltage, we can detect the end of the
conduction time of secondary diode. The constant current
control block picks up the leakage inductor current, the end
of conduction of the output rectifier and controls the drain
current to maintain the output current constant.
We have:
(eq. 1)
The output diode current increase is limited by the leakage
inductor. As a consequence, the secondary peak current is
reduced:
I D,pk t
I L,pk
N sp
(eq. 2)
I out +
The diode current reaches its peak when the leakage inductor
is reset. Thus, in order to accurately regulate the output
current, we need to take into account the leakage inductor
current. This is accomplished by sensing the clamping
network current. Practically, a node of the clamp capacitor
is connected to Rsense instead of the bulk voltage Vbulk.
Then, by reading the voltage on the CS pin, we have an
image of the primary current (red curve in Figure 47).
V REF
2N spR sense
(eq. 3)
The output current value is set by choosing the sense
resistor:
R sense +
V ref
2N spI out
(eq. 4)
From Equation 3, the first key point is that the output
current is independent of the inductor value. Moreover, the
leakage inductance does not influence the output current
value as the reset time is taken into account by the controller.
http://onsemi.com
16
NCL30082
IL,pk
NspID,pk
Ipri(t)
Isec(t)
time
t1
t2
ton
tdemag
Vaux(t)
time
Figure 47. Flyback Currents and Auxiliary Winding Voltage in DCM
Internal Soft−Start
At startup or after recovering from a fault, there is a small
internal soft−start of 40 ms.
In addition, during startup, as the output voltage is zero
volts, the demagnetization time is long and the constant
current control block will slowly increase the peak current
towards its nominal value as the output voltage grows.
Figure 48 shows a soft−start simulation example for a 9 W
LED power supply.
http://onsemi.com
17
NCL30082
16.0
(V)
12.0
1
Vout
2
I out
4
VControl
3
VCS
8.00
4.00
0
800m
(A)
600m
400m
200m
0
800m
(V)
600m
400m
200m
0
604u
1.47m
2.34m
time in seconds
3.21m
4.07m
Figure 48. Startup Simulation Showing the Natural Soft−start
Cycle−by−Cycle Current Limit
Winding and Output Diode Short−Circuit Protection
When the current sense voltage exceeds the internal
threshold VILIM, the MOSFET is turned off for the rest of the
switching cycle (Figure 49).
In parallel with the cycle−by−cycle sensing of the CS pin,
another comparator with a reduced LEB (tBCS) and a higher
threshold (1.5 V typical) is able to sense winding
short−circuit and immediately stops the DRV pulses. The
controller goes into auto−recovery mode in version B.
In version A, the controller is latched. In latch mode, the
DRV pulses stop and VCC ramps up and down. The circuit
un−latches when VCC pin voltage drops below VCC(reset)
threshold.
http://onsemi.com
18
NCL30082
S
CS
LEB1
Rsense
Vcc
management
PWMreset
VCC
−
+
VCCstop
UVLO
grand
8_HICC
reset
Ipkmax
−
VILIMIT
OVP
LEB2
aux
Vdd
latch
R
+
Vcontrol
DRV
Q
Q
+
STOP
WOD_SCP
−
S
VCS(stop)
Q
Q
OVP
OFF WOD_SCP
latch
S
Q
Q
R
8_HICC
R
grand
reset
from Fault Management Block
Figure 49. Winding Short Circuit Protection, Max. Peak Current Limit Circuits
Thermal Fold−back and Over Voltage / Over
Temperature Protection
If VSD drops below VOTP, the controller enters into the
auto−recovery fault mode for version B, meaning that the
4−s timer is activated. The controller will re−start switching
after the 4−s timer has elapsed and when VSD > VOTP(on) to
provide some temperature hysteresis (around 10°C).
For version A, this protection is latched: reset occurs when
VCC < VCC(reset).
The thermal fold−back and OTP thresholds correspond
roughly to the following resistances:
• Thermal fold−back starts when RNTC ≤ 11.76 kW.
• Thermal fold−back stops when RNTC ≤ 8.24 kW.
• OTP triggers when RNTC ≤ 5.88 kW.
• OTP is removed when RNTC ≥ 8.24 kW.
The thermal fold−back circuit reduces the current in the
LED string when the ambient temperature exceeds a set
point. The current is gradually reduced to 50% of its nominal
value if the temperature continues to rise. (Figure 50). The
thermal foldback starting temperature depends of the
Negative Coefficient Temperature (NTC) resistor chosen by
the power supply designer.
Indeed, the SD pin allows the direct connection of an NTC
to sense the ambient temperature. When the SD pin voltage
VSD drops below VTF(start), the internal reference for the
constant current control VREF is decreased proportionally to
VSD. When VSD reaches VTF(stop), VREF is clamped to
VREF50, corresponding to 50% of the nominal output
current.
Temperature increases
Temperature decreases
Iout
Iout(nom)
Shutdown
50% Iout(nom)
VOTP(off)
VTF(stop)
VOTP(on)
VTF(start)
VSD
Figure 50. Output Current Reduction versus SD Pin Voltage
http://onsemi.com
19
NCL30082
At startup, when VCC reaches VCC(on), the controller is
not allowed to start pulsing for at least 180 ms in order to
allow the SD pin voltage to reach its nominal value if a
filtering capacitor is connected to the SD pin. This is to avoid
flickering of the LED light in case of over temperature.
VOVP
VCC
Vdd
noise delay
−
Dz
IOTP(REF)
OVP
+
S
SD
Q
OFF
Q
OTP_Timer end
Rclamp
Clamp
Vclamp
R
OTP
−
NTC
noise delay
4−s Timer
+
VOTP
(OTP latched for version A)
0.5 V if OTP low
0.7 V if OTP high
S
Q
Latch
Q
VTF
R
VCCreset
Figure 51. Thermal Fold−back and OVP/OTP Circuitry
In the case of excess voltage, the Zener diode starts to
conduct and inject current into the internal clamp resistor
Rclamp thus causing the pin SD voltage to increase. When
this voltage reaches the OVP threshold (2.5 V typ.), the
controller shuts−down and waits for at least 4 seconds before
restarting switching.
http://onsemi.com
20
NCL30082
VCC
VCC(on)
VCC(off)
VCC > VCC(on):
DRV pulses restart
VCC(reset)
VDRV
4−s Timer
VSD
VSD > VOVP:
controller stops
switching
4−s timer has elapsed:
waiting for VCC > VCC(on)
to restart DRV pulses
VOVP
VSD(clamp)
Vout
Figure 52. OVP with SD Pin Chronograms
http://onsemi.com
21
NCL30082
VCC
VCC(on)
VCC(off)
VCC(reset)
VDRV
VSD > VTF(stop) and
VCC > VCC(on):
DRV pulses restart
4−s Timer
VSD < VOTP(off):
controller stops
switching
VSD
VTF(start)
4−s timer has elapsed
but VSD < VTF(stop)
≥ no restart
VTF(stop)
VOTP(off)
Iout
Figure 53. Thermal Fold−back / OTP Chronograms
PWM or Linear Dimming Detection
The pin DIM allows implementing either linear dimming
or PWM dimming of the LED light.
If the power supply designer apply an analog signal
varying from VDIM(EN) to VDIM100 to the DIM pin, the
output current will increase or decrease proportionally to the
voltage applied. For VDIM = VDIM100, the power supply
delivers the maximum output current.
VDIM
If a voltage lower than VDIM(EN) is applied to the DIM pin,
the DRV pulses are disabled. Thus, for PWM dimming, a
PWM signal with a low state value < VDIM(EN) and a high
state value > VDIM100 should be applied.
The DIM pin is pulled up internally by a small current
source. Thus, if the pin is left open, the controller is able to
start.
Analog dimming
PWM dimming
VDIM100
100% Iout
VDIM(EN)
0% Iout
Figure 54. Pin DIM Chronograms
Note:
• If a PWM voltage with a high state value < VDIM100 is
applied to the DIM pin, the product will still be in
PWM dimming mode, but the reference voltage will be
decreased according to VDIM. This allows increased
dynamic range on the dimming control pin.
• Thermal Foldback and dimming: if the IC is in a
dimming state and the thermal foldback (TF) is
activated, the output current is further reduced to a
value equal to Dimming*TF.
http://onsemi.com
22
NCL30082
VCC Over Voltage Protection (Open LED Protection)
In the NCL30082, when the VCC voltage reaches the
VCC(OVP) threshold, the controller stops the DRV pulses and
the 4−s timer starts counting. The IC re−start pulsing after
the 4−s timer has elapsed and when VCC ≥ VCC(on).
If no output load is connected to the LED power supply,
the controller must be able to safely limit the output voltage
excursion.
40.0
V CC(OVP)
(V)
30.0
1 V CC
VCC(on)
20.0
10.0
VCC(off)
0
40.0
(V)
30.0
2 Vout
20.0
10.0
0
800m
(A)
600m
400m
200m
3 I out
0
8.00
(V)
6.00
4 OVP
4.00
2.00
0
1.38
3.96
6.54
time in seconds
9.11
11.7
Figure 55. Open LED Protection Chronograms
Valley Lockout
or the output current set−point varies significantly. This
avoids valley jumping and the inherent noise caused by this
phenomenon.
The input voltage is sensed by the VIN pin (line range
detection in Figure 56). The internal logic selects the
operating valley according to VIN pin voltage, SD pin
voltage and DIM pin voltage.
By default, when the output current is not dimmed, the
controller operates in the first valley at low line and in the
second valley at high line.
Quasi−square wave resonant systems have a wide
switching frequency excursion. The switching frequency
increases when the output load decreases or when the input
voltage increases. The switching frequency of such systems
must be limited.
The NCL30082 changes the valley as the input voltage
increases and as the output current set−point is varied
(dimming and thermal fold−back). This limits the switching
frequency excursion. Once a valley is selected, the
controller stays locked in the valley until the input voltage
http://onsemi.com
23
NCL30082
Vbulk
VIN
+
LLine
HLine
25−ms blanking time
−
2.4 V if LLine low
2.3 V if LLine high
Figure 56. Line Range Detector
Table 4. VALLEY SELECTION
VIN pin voltage for valley change
Iout value at which the
controller changes valley
(Iout decreasing)
0
100%
75%
50%
30%
15%
6%
0%
0
−LL−
2.3 V
−HL−
1st
2nd
2nd
3rd
4th
5th
7th
8th
11th
12th
13th
15th
−LL−
2.4 V
−HL−
VVIN increases
VIN pin voltage for valley change
http://onsemi.com
24
5V
100%
78%
53%
33%
20%
8%
0%
5V
Iout increases
Iout decreases
Iout value at which the
controller changes valley
(Iout increasing)
VVIN decreases
NCL30082
Zero Crossing Detection Block
the valleys. To avoid such a situation, the NCL30082
features a Time−Out circuit that generates pulses if the
voltage on ZCD pin stays below the VZCD(THD) threshold
for 6.5 ms.
The time−out also acts as a substitute clock for the valley
detection and simulates a missing valley in case of too
damped free oscillations.
The ZCD pin allows detecting when the drain−source
voltage of the power MOSFET reaches a valley.
A valley is detected when the voltage on pin 1 crosses
below the VZCD(THD) internal threshold.
At startup or in case of extremely damped free
oscillations, the ZCD comparator may not be able to detect
V ZCD
3
4
high
V ZCD(THD)
The 3rd valley
is validated
14
2nd, 3rd
low
12
The 3rd valley is not detected
by the ZCD comp
The 2nd valley is detected
By the ZCD comparator
high
15 ZCD comp
low
high
low
16
TimeOut
17
Clk
Time−out circuit adds a pulse to
account for the missing 3rd valley
high
low
Figure 57. Time−out Chronograms
Normally with this type of time−out function, in the event
the ZCD pin or the auxiliary winding is shorted, the
controller could continue switching leading to improper
regulation of the LED current. Moreover during an output
short circuit, the controller will strive to maintain constant
current operation.
To avoid these scenarios, a protection circuit consisting of
a comparator and secondary timer starts counting when the
ZCD voltage is below the VZCD(short) threshold. If this timer
reaches 90 ms, the controller detects a fault and shutdown.
The auto−restart version (B suffix) waits 4 seconds, then the
controller restarts switching. In the latched version
(A suffix), the controller is latched as long as VCC stays
above the VCC(reset) threshold.
http://onsemi.com
25
NCL30082
Tblank
Time−Out
ZCD
+
VZCD(TH)
.
Clock
−
Tblank
VZCD(short)
+
−
90−ms
Timer
Enable_b
S
Q
Aux_SCP
Q
R
4−s Timer
Figure 58. ZCD Block Schematic
Line Feed−Forward
Because of the propagation delays, the MOSFET is not
turned−off immediately when the current set−point is
reached. As a result, the primary peak current is higher than
expected and the output current increases. To compensate
the peak current increase brought by the propagation delay,
a positive voltage proportional to the line voltage is added
on the current sense signal. The amount of offset voltage can
be adjusted using the RCS resistor as shown in Figure 59.
V CS(offset) + K LFFV pinVINR CS
(eq. 5)
The offset voltage is applied only during the MOSFET
on−time.
This offset voltage is removed at light load during
dimming when the output current drops below 15% of the
programmed output current.
Bulk rail
VDD
VIN
ICS(offset)
CS
RCS
Rsense
Q_drv
Offset_OK
Figure 59. Line Feed−Forward Schematic
http://onsemi.com
26
NCL30082
Brown−out
shuts−down if the VIN pin voltage decreases and stays
below 0.9 V for 50 ms nominal. Exiting a brown−out
condition overrides the hiccup on VCC (VCC does not wait
to reach VCC(off)) and the IC immediately goes into startup
mode (ICC = ICC(start)).
In order to protect the supply against a very low input
voltage, the NCL30082 features a brown−out circuit with a
fixed ON/OFF threshold. The controller is allowed to start
if a voltage higher than 1 V is applied to the VIN pin and
Vbulk
VIN
+
BO_NOK
50−ms blanking time
−
1 V if BONOK high
0.9 V if BONOK low
Figure 60. Brown−out Circuit
160
(V)
120
VBulk
80.0
1
40.0
0
18.0
(V)
2
VCC(on)
16.0
14.0
VCC
12.0
VCC(off)
10.0
1.10
V BO(on)
(V)
900m
V BO(off)
700m
V pinVIN
500m
3
300m
8.00
50−ms Timer
(V)
6.00
BO_NOK low
=> Startup mode
4.00
2.00
BO_NOK
4
0
46.1m
138m
231m
time in seconds
323m
Figure 61. Brown−Out Chronograms (Valley Fill circuit is used)
http://onsemi.com
27
415m
NCL30082
CS Pin Short Circuit Protection
Normally, if the CS pin or the sense resistor is shorted to
ground, the Driver will not be able to turn off, leading to
potential damage of the power supply. To avoid this, the
NCL30082A and the NCL30082B features a circuit to
protect the power supply against a short circuit of the CS pin.
When the MOSFET is on, if the CS voltage stays below
VCS(low) after the adaptive blanking timer has elapsed, the
controller shuts down and will attempt to restart on the next
VCC hiccup. In the NCL30082B1, this protection is
disabled.
Adaptative
Blanking Time
VVIN
Q_drv
CS
−
S
+
VCS(low)
Q
CS_short
Q
R
UVLO
BO_NOK
Figure 62. CS Pin Short Circuit Protection Schematic
Fault Management
In this mode, the DRV pulses are stopped. The VCC
voltage decrease through the controller own consumption
(ICC1).
For the output diode short circuit protection, the CS pin
short circuit protection, the output / aux. winding short
circuit protection and the OVP2, the controller waits 4
seconds (auto−recovery timer) and then initiates a startup
sequence (VCC ≥ VCC(on)) before re−starting switching.
Latch Mode
This mode is activated by the output diode short−circuit
protection (WOD_SCP), the OTP and the Aux−SCP in
version A only.
In this mode, the DRV pulses are stopped and the
controller is latched. There are hiccups on VCC.
The circuit un−latches when VCC < VCC(reset).
OFF Mode
The circuit turns off whenever a major condition prevents
it from operating:
• Incorrect feeding of the circuit: “UVLO high”. The
UVLO signal becomes high when VCC drops below
VCC(off) and remains high until VCC exceeds VCC(on).
• OTP
• VCC OVP
• OVP2 (additional OVP provided by SD pin)
• Output diode short circuit protection: “WOD_SCP
high”
• Output / Auxiliary winding Short circuit protection:
“Aux_SCP high”
• Die over temperature (TSD)
• Brown−Out: “BO_NOK” high
• Pin CS short circuited to GND: “CS_short high”
http://onsemi.com
28
NCL30082
Reset
Timer has
finished
counting
VCC > VCC(on)
OVP2 or
VCC_OVP
BO_NOK high
or OTP
or TSD
or CS_Short
Stop
4−s
Timer
VCC
Disch.
BO_NOK high
or OTP
or TSD
or CS_Short
OVP2
or WOD_SCP
or Aux_SCP
or VCC_OVP
With states: Reset
Stop
Run
VCC Disch.
4−s Timer
→
→
→
→
→
VCC < VCC(off)
or
BO_NOK ↓
Run
VCC < VCC(off)
Controller is reset, ICC = ICC(start)
Controller is ON, DRV is not switching, tOTP(start) has elapsed
Normal switching
No switching, ICC = ICC1, waiting for VCC to decrease to VCC(off)
the auto−recovery timer is counting, VCC is ramping up and down between VCC(on) and VCC(off)
Note: For the NCL30082B1, the CS pin short circuit Protection is disabled
Figure 63. State Diagram for B Version Faults
http://onsemi.com
29
NCL30082
Reset
Timer has
finished
counting
VCC < VCC(reset)
4−s
Timer
OVP2 or
VCC_OVP
VCC > VCC(on)
OVP2 or
VCC_OVP
VCC < VCC(off)
or
BO_NOK ↓
BO_NOK high
or TSD
or CS_Short
Stop
VCC
Disch.
OTP
BO_NOK high
or TSD
or CS_Short
Latch
Run
OTP or
WOD_SCP or
Aux_SCP
With states: Reset
Stop
Run
VCC Disch.
4−s Timer
Latch
→
→
→
→
→
→
VCC < VCC(off)
Controller is reset, ICC = ICC(start)
Controller is ON, DRV is not switching, tOTP(start) has elapsed
Normal switching
No switching, ICC = ICC1, waiting for VCC to decrease to VCC(off)
the auto−recovery timer is counting, VCC is ramping up and down between VCC(on) and VCC(off)
Controller is latched off, VCC is ramping up and down between VCC(on) and VCC(off),
only VCC(reset) can release the latch.
Figure 64. State Diagram for A Version Faults
http://onsemi.com
30
NCL30082
PACKAGE DIMENSIONS
Micro8t
CASE 846A−02
ISSUE H
D
HE
PIN 1 ID
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE
BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED
0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE.
5. 846A-01 OBSOLETE, NEW STANDARD 846A-02.
E
e
b 8 PL
0.08 (0.003)
T B
M
S
A
DIM
A
A1
b
c
D
E
e
L
HE
S
SEATING
−T− PLANE
0.038 (0.0015)
A
A1
MILLIMETERS
NOM
MAX
−−
1.10
0.08
0.15
0.33
0.40
0.18
0.23
3.00
3.10
3.00
3.10
0.65 BSC
0.40
0.55
0.70
4.75
4.90
5.05
MIN
−−
0.05
0.25
0.13
2.90
2.90
L
c
SOLDERING FOOTPRINT*
8X
1.04
0.041
0.38
0.015
3.20
0.126
6X
8X
4.24
0.167
0.65
0.0256
5.28
0.208
SCALE 8:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
31
INCHES
NOM
−−
0.003
0.013
0.007
0.118
0.118
0.026 BSC
0.016
0.021
0.187
0.193
MIN
−−
0.002
0.010
0.005
0.114
0.114
MAX
0.043
0.006
0.016
0.009
0.122
0.122
0.028
0.199
NCL30082
OPTIONS
Controller
Output SCP
Winding/Output
Diode SCP
Over Temperature Protection
CS Pin
Short Protection
NCL30082A
Latched
Latched
Latched
Yes
NCL30082B
Auto−recovery
Auto−recovery
Auto−recovery
Yes
NCL30082B1
Auto−recovery
Auto−recovery
Auto−recovery
No
ORDERING INFORMATION
Device
Package Marking
Package Type
Shipping†
NCL30082ADMR2G
AAC
Micro8
(Pb−Free,Halide−Free)
4000 / Tape & Reel
NCL30082BDMR2G
AAD
Micro8
(Pb−Free,Halide−Free)
4000 / Tape & Reel
NCL30082B1DMR2G
AAH
Micro8
(Pb−Free,Halide−Free)
4000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
32
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCL30082/D
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
ON Semiconductor:
NCL30082ADMR2G NCL30082BDMR2G