® OPA OPA2658 265 OPA 8 265 8 Dual Wideband, Low Power, Current Feedback OPERATIONAL AMPLIFIER FEATURES APPLICATIONS ● UNITY GAIN STABLE BANDWIDTH: 800MHz ● LOW POWER: 50mW/Chan. ● MEDICAL IMAGING ● HIGH-RESOLUTION VIDEO ● HIGH-SPEED SIGNAL PROCESSING ● LOW DIFFERENTIAL GAIN/PHASE ERRORS: 0.01%/0.03° ● COMMUNICATIONS ● PULSE AMPLIFIERS ● ADC/DAC GAIN AMPLIFIER ● HIGH SLEW RATE: 1700V/µs ● PACKAGE: 8-Pin DIP, SO-8 and MSOP-8 ● MONITOR PREAMPLIFIER ● CCD IMAGING AMPLIFIER DESCRIPTION The OPA2658 is a dual, ultra-wideband, low power current feedback video operational amplifier featuring high slew rate and low differential gain/phase error. The current feedback design allows for superior large signal bandwidth, even at high gains. The low differential gain/phase errors, wide bandwidth and low quiescent current make the OPA2658 a perfect choice for numerous video, imaging and communications applications. The OPA2658 is optimized for low gain operation, and is also available in single, OPA658 and quad, OPA4658 configurations. +VS Current Mirror IBIAS +Input –Input Buffer VOUT CCOMP IBIAS Current Mirror –VS NOTE: Diagram reflects only one-half of the OPA2658 International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111 Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 ® © 1994 Burr-Brown Corporation PDS-1269D 1 Printed in U.S.A. March, 1998 OPA2658 SPECIFICATIONS At TA = +25°C, VS = ±5V, RL = 100Ω, RFB = 402Ω, unless otherwise noted. OPA2658P, U, E PARAMETER CONDITION FREQUENCY RESPONSE Closed-Loop Bandwidth(2) Bandwidth for 0.1dB Flatness(2) Slew Rate(4) Over Temperature Range Settling Time: 0.01% 0.1% 1% Spurious Free Dynamic Range Third-Order Intercept Point Differential Gain Differential Phase Crosstalk OFFSET VOLTAGE Input Offset Voltage Over Temperature Range Power Supply Rejection INPUT BIAS CURRENT Non-Inverting Over Temperature Range Inverting Over Temperature Range NOISE Input Voltage Noise Noise Density: f = 100Hz f = 10kHz f ≥ 1MHz Integrated Noise: fB = 100Hz to 200MHz Input Bias Current Noise Density Inverting: f ≥ 1MHz Non-Inverting: f ≥ 1MHz INPUT VOLTAGE RANGE Common-mode Input Range Over Temperature Range Common-mode Rejection INPUT IMPEDANCE Non-Inverting Inverting OPEN-LOOP TRANSIMPEDANCE Open-loop Transimpedance Over Temperature Range OUTPUT Voltage Output Over Temperature Range Voltage Output Over Temperature Range Voltage Output Over Temperature Range Output Current, Sourcing Over Temperature Range Output Current, Sinking Over Temperature Range Short Circuit Current Output Resistance POWER SUPPLY Specified Operating Voltage Operating Voltage Range Quiescent Current Over Temperature THERMAL CHARACTERISTICS Temperature Range Thermal Resistance, θJA P 8-Pin DIP U SO-8 E MSOP-8 MIN G = +1(3) G = +2 G = +5 G = +10 VO < 0.5Vp-p G = +2, 2V Step VCM = 0V 55 VCM = 0V VCM = 0V ±2.5 45 Input Referred, VCM = ±1V MAX 800 500 210 130 135 1700 1500 15 12.6 4.8 68 56 39 0.01 0.03 –78 G = +2, 2V Step G = +2, 2V Step G = +2, 2V Step f = 5MHz, G = +2, VO = 2Vp-p f = 20MHz, G = +2, VO = 2Vp-p f = 10MHz, 4dBm, Each Tone G = +2, NTSC, VO = 1.4Vp-p, RL = 150Ω G = +2, NTSC, VO = 1.4Vp-p, RL = 150Ω Input Referred, 5MHz, Channel-to-Channel Input Referred, VS = ±4.5 to ±5.5V TYP OPA2658UB MIN 300 1000 900 ±3 ±5 64 ±5.5 ±8 ±4.0 ±10 ±2.9 ±30 ±30 ±80 ±35 ±75 58 TYP MAX ✻(1) ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ UNITS MHz MHz MHz MHz MHz V/µs V/µs ns ns ns dB dB dBm % degrees dB ±2 ±4 68 ±4.5 ±7 mV mV dB ✻ ✻ ✻ ✻ ±18 ±35 ✻ ✻ µA µA µA µA 16 3.6 3.2 ✻ ✻ ✻ nV/√Hz nV/√Hz nV/√Hz 45 ✻ µVr ms 32 11.9 ✻ ✻ pA/√Hz pA/√Hz ✻ ✻ V V dB ✻ ✻ kΩ || pF Ω ±2.9 ✻ ✻ 50 500 || 1 50 VO = ±2V, RL = 100Ω 150 100 180 200 150 ✻ kΩ kΩ No Load ±2.7 ±2.5 ±2.7 ±2.5 ±2.2 ±2.0 80 70 60 35 ±3.0 ±2.8 ±2.9 ±2.8 ±2.6 ±2.4 120 ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ V V V V V V mA mA mA mA mA Ω RL = 250Ω RL = 100Ω 80 ✻ ✻ 150 0.06 f < 100kHz, G = +2 ±4.5 Both Channels, VS = ±5V Specification: P, U, E, UB ±5 ±10 ±11 –40 100 125 150 ✻ ✻ ±5.5 ±15.5 ±17 ✻ +85 ✻ ✻ ✻ ✻ ✻ ✻ ✻ ±11.5 ±13 V V mA mA ✻ °C °C/W °C/W °C/W NOTES: (1) An asterisk (✻) specifies the same value as the grade to the left. (2) Frequency response can be strongly influenced by PC board parasitics. The demonstration boards show low parasitic layouts for this part. Refer to the demonstration board layout for details. (3) At G = +1, RFB = 560Ω for DIP and MSOP-8, and 402Ω for SO-8. (4) Slew rate is rate of change from 10% to 90% of output voltage step. ® OPA2658 2 ABSOLUTE MAXIMUM RATINGS ELECTROSTATIC DISCHARGE SENSITIVITY Supply Voltage ................................................................................. ±5.5V Internal Power Dissipation .......................... See Thermal Characteristics Differential Input Voltage .................................................................. ±1.2V Input Voltage Range ............................................................................ ±VS Storage Temperature Range: P, U, UB, E ................... –40°C to +125°C Lead Temperature (DIP, soldering, 10s) ..................................... +300°C (SO-8 and MSOP-8, soldering, 3s) ................ +260°C Junction Temperature (TJ ) ............................................................ +175°C This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PIN CONFIGURATION Top View DIP/SO-8/MSOP-8 Output 1 1 8 +VS –Input 1 2 7 Output 2 +Input 1 3 6 –Input 2 –VS 4 5 +Input 2 PACKAGE/ORDERING INFORMATION PRODUCT PACKAGE PACKAGE DRAWING NUMBER(1) OPA2658P OPA2658U 8-Pin Plastic DIP SO-8 Surface Mount 006 182 –40°C to +85°C –40°C to +85°C OPA2658P OPA2658U OPA2658P OPA2658U OPA2658UB SO-8 Surface Mount 182 –40°C to +85°C OPA2658UB OPA2658UB 8-Pin MSOP-8 337 –40°C to +85°C B58 OPA2658E-250 OPA2658E-2500 OPA2658E TEMPERATURE RANGE PACKAGE MARKING(2) ORDERING NUMBER(3) NOTE: (1) For detailed drawing and dimension table, see end of data sheet, or Appendix C of Burr-Brown IC Data Book. (2) The “B” grade will be marked with a “B” by pin 8. (3) The MSOP-8 is available on 7" tape and reel with 250 parts, and on 14" tape and reel with 2500 parts. For example, ordering 250 pieces of “OPA2658E-250” will get a single 250 piece tape and reel. Refer to Appendix B of Burr-Brown IC Data Book for detailed Tape and Reel Mechanical information. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. ® 3 OPA2658 TYPICAL PERFORMANCE CURVES At TA = +25°C, VS = ±5V, RL = 100Ω, RFB = 402Ω, unless otherwise noted. PSRR AND CMR vs TEMPERATURE 55 75 50 70 PSRR , CMR (dB) Common-Mode Rejection (dB) COMMON-MODE REJECTION vs INPUT COMMON-MODE VOLTAGE 45 40 35 PSRR 65 PSR+ 60 PSR– 55 CMR 30 50 25 –4 –3 –2 –1 0 1 2 3 45 –50 4 –25 0 Common-Mode Voltage (V) 25 50 75 100 Temperature (°C) OUTPUT CURRENT vs TEMPERATURE SUPPLY CURRENT vs TEMPERATURE 120 Output Current (±mA) Supply Current /Chan. (±mA) I O+ 5 4 110 100 90 80 IO– 70 –50 –25 0 25 50 75 –50 100 50 75 OUTPUT SWING vs TEMPERATURE NON-INVERTING INPUT BIAS CURRENT vs TEMPERATURE Non-Inverting Input Bias Current IB+ (µA) RL = 250Ω 3.0 Output Swing (V) 25 Ambient Temperature (°C) 3.10 –VO +VO 2.90 2.80 2.70 –VO 2.60 +VO RL = 100Ω 2.50 2.40 2.30 –20 0 Ambient Temperature (°C) 3.20 –40 –25 0 20 40 60 80 100 8 6 4 2 –25 0 25 50 Ambient Temperature (°C) ® OPA2658 10 –50 Temperature (°C) 4 100 75 100 TYPICAL PERFORMANCE CURVES (CONT) At TA = +25°C, VS = ±5V, RL = 100Ω, RFB = 402Ω, unless otherwise noted. OPEN-LOOP TRANSIMPEDANCE AND PHASE vs FREQUENCY INVERTING INPUT BIAS CURRENT vs TEMPERATURE 106 Transimpedance 105 1.6 1.4 1.2 1.0 0.8 0.6 0 104 –45 Phase 103 –90 102 –135 101 –180 –225 1 0.4 –50 –25 0 25 50 75 1k 100 10k Temperature (°C) OPEN-LOOP GAIN AND PHASE vs FREQUENCY 100k 1M 10M Frequency (Hz) 100M 1G CLOSED-LOOP BANDWIDTH 60 6 Gain SO-8 Bandwidth = 881MHz, RFB = 402Ω 0 20 –45 0 –90 3 G = +1 Gain (dB) Phase Open-Loop Phase (°) 40 Open-Loop Gain (dB) Open-Loop Phase (°) 1.8 Transimpedance (Ω) Inverting Input Bias Current IB– (µA) 2.0 0 –135 –40 –180 –6 –225 –9 –60 1k 10k 100k 1M 10M 100M DIP Bandwidth = 949MHz, RFB = 560Ω –3 –20 1G MSOP-8 Bandwidth = 600MHz, RFB = 560Ω 1M 10M Frequency (Hz) 100M 1G Frequency (Hz) CLOSED-LOOP BANDWIDTH CLOSED-LOOP BANDWIDTH 20 9 G = +5 G = +2 17 6 MSOP-8/SO-8/DIP Bandwidth= 372MHz 14 Gain (dB) Gain (dB) DIP Bandwidth = 682MHz 3 SO-8 Bandwidth = 680MHz 0 11 8 –3 5 MSOP-8 Bandwidth = 351MHz 2 –6 1M 10M 100M 1M 1G 10M 100M 1G Frequency (Hz) Frequency (Hz) ® 5 OPA2658 TYPICAL PERFORMANCE CURVES (CONT) At TA = +25°C, VS = ±5V, RL = 100Ω, RFB = 402Ω, unless otherwise noted. SMALL SIGNAL TRANSIENT RESPONSE CLOSED-LOOP BANDWIDTH 26 160 MSOP-8/SO-8/DIP Bandwidth = 200MHz Output Voltage (mV) G = +10 20 Gain (dB) G = +2 120 23 17 14 11 80 40 0 –40 –80 –120 8 –160 1M 10M 100M 1G Time (5ns/div) Frequency (Hz) RECOMMENDED ISOLATION RESISTANCE vs CAPACITIVE LOAD LARGE SIGNAL TRANSIENT RESPONSE 1.6 40 G = +2 1.2 G = +2 Output Voltage (V) Isolation Resistance 35 30 RISO 25 OPA658 20 CL 402Ω 15 1kΩ 0.8 0.4 0 –0.4 –0.8 402Ω –1.2 –1.6 10 10 20 Time (5ns/div) 30 40 50 60 70 80 90 100 Capacitive Load (pf) HARMONIC DISTORTION vs FREQUENCY 5MHz HARMONIC DISTORTION vs OUTPUT SWING –60 –50 Harmonic Distortion (dBc) Harmonic Distortion (dBc) –65 –60 –70 –80 2fO –90 3fO 3fO –70 2fO –75 G = +2 –80 –85 –90 –95 –100 –100 100k 1M 10M 0 100M ® OPA2658 1 2 Output Swing (Vp-p) Frequency (Hz) 6 3 4 TYPICAL PERFORMANCE CURVES (CONT) At TA = +25°C, VS = ±5V, RL = 100Ω, RFB = 402Ω, unless otherwise noted. HARMONIC DISTORTION vs TEMPERATURE (VO = 2Vp-p, G = +2) 10MHz HARMONIC DISTORTION vs OUTPUT SWING –60 Harmonic Distortion (dBc) Harmonic Distortion (dBc) –60 –70 2fO –80 3fO –90 –100 0.01 3fO –70 2fO –75 –80 –85 1 0.1 4V 10 –75 –50 –25 0 25 50 75 100 Output Swing (Vp-p) Temperature (°C) HARMONIC DISTORTION vs GAIN (fO = 5MHz, VO = 2Vp-p) INPUT VOLTAGE AND CURRENT NOISE vs FREQUENCY 125 100 –50 –55 Voltage Noise (nV/√Hz) Current Noise (pA/√Hz) Harmonic Distortion (dBc) –65 2fO –60 3fO –65 –70 Inverting Current Noise Non-Inverting Noise 10 Voltage Noise 1 –75 0 1 2 3 4 5 6 7 8 9 102 10 103 104 105 106 107 Frequency (Hz) Non-Inverting Gain (V/V) ® 7 OPA2658 APPLICATIONS INFORMATION For non-inverting operation, the input signal is applied to the non-inverting (high impedance buffer) input. The output (buffer) error current (IE) is generated at the low impedance inverting input. The signal generated at the output is fed back to the inverting input such that the overall gain is (1 + RFB/RFF). Where a voltage-feedback amplifier has two symmetrical high impedance inputs, a current feedback amplifier has a low inverting (buffer output) impedance and a high non-inverting (buffer input) impedance. The closed-loop gain for the OPA2658 can be calculated using the following equations: R – FB R FF Inverting Gain = 1 (1) 1+ Loop Gain THEORY OF OPERATION Conventional op amps depend on feedback to drive their inputs to the same potential, however the current feedback op amp’s inverting and non-inverting inputs are connected by a unity gain buffer, thus enabling the inverting input to automatically assume the same potential as the non-inverting input. This results in very low impedance at the inverting input, which makes it a very good current sensor. The feedback loop reduces the error current seen at the inverting input to a very small value. DISCUSSION OF PERFORMANCE The OPA2658 is a dual, low-power, unity gain stable, current feedback operational amplifier which operates on ±5V power supply. The current feedback architecture offers the following important advantages over voltage feedback architectures: (1) the high slew rate allows the large signal performance to approach the small signal performance, and (2) there is very little bandwidth degradation at higher gain settings. The current feedback architecture of the OPA2658 provides the traditional strength of excellent large signal response plus wide bandwidth, making it a good choice for use in high resolution video, medical imaging and DAC I/V Conversion. The low power requirements make it an excellent choice for numerous portable applications. R FB 1 + R FF Non−Inverting Gain = 1 1+ Loop Gain TO where Loop Gain = R FB R FB + R S 1 + R FF At higher gains the small value inverting input impedance causes an apparent loss in bandwidth. This can be seen from the equation: ƒ ( A = +2 ) BW x (1. 25) V (3) ƒ ACTUAL BW ≈ RS R FB 1 + × 1 + R FF R FB [ DC GAIN TRANSFER CHARACTERISTICS The circuit in Figure 1 shows the equivalent circuit for calculating the DC gain. When operating the device in the inverting mode, the input signal error current (IE) is amplified by the open loop transimpedance gain (TO). The output signal generated is equal to TO x IE. Negative feedback is applied through RFB such that the device operates at a gain equal to –RFB/RFF. IE RFF RS LS TO – VN OFFSET VOLTAGE AND NOISE The output offset is the algebraic sum of the input offset voltage and bias current errors, all with different gains to the output. The output offset for non-inverting operation is calculated by the following equation: R Output Offset Voltage = ±Ib N × R N 1 + F B ± (4) R FF R FB V IO 1 + ±Ib I × R FB R FF If all terms are divided by the gain (1 + RFB/RFF) it can be observed that the input referred offset improves as gain increases, and as RN decreases. VO (50Ω) C1 VI ] This loss in bandwidth at high gains can be corrected without affecting stability by lowering the value of the feedback resistor from the specified value of 402Ω. CC + RFB RFF IbI IbN RFB RN VIO FIGURE 1. Equivalent Circuit. (1/2 of OPA2658) FIGURE 2. Output Offset Voltage Equivalent Circuit. ® OPA2658 (2) 8 The feedback resistor value acts as the frequency response compensation element for a current feedback type amplifier. The 402Ω used in setting the specification achieves a nominal maximally flat Butterworth response while assuming a 2pF output pin parasitic. Increasing the feedback resistor will over compensate the amplifier, rolling off the frequency response, while decreasing it will decrease phase margin, peaking up the frequency response. Note that a non-inverting, unity gain buffer application still requires a feedback resistor for stability (560Ω for SO-8, 402Ω for PDIP and 560Ω for MSOP-8). d) Connections to other wideband devices on the board may be made with short direct traces or through on-board transmission lines. For short connections, consider the trace and the input to the next device as a lumped capacitive load. Relatively wide traces (50 to 100 mils) should be used, preferably with ground and power planes opened up around them. Estimate the total capacitive load and set RISO from the plot of recommended RISO vs capacitive load. Low parasitic loads may not need an RISO since the OPA2658 is nominally compensated to operate with a 2pF parasitic load. If a long trace is required and the 6dB signal loss intrinsic to doubly terminated transmission lines is acceptable, implement a matched impedance transmission line using microstrip or stripline techniques (consult an ECL design handbook for microstrip and stripline layout techniques). A 50Ω environment is not necessary on board, and in fact a higher impedance environment will improve distortion as shown in the distortion vs load plot. With a characteristic impedance defined based on board material and desired trace dimensions, a matching series resistor into the trace from the output of the amplifier is used as well as a terminating shunt resistor at the input of the destination device. Remember also that the terminating impedance will be the parallel combination of the shunt resistor and the input impedance of the destination device; the total effective impedance should match the trace impedance. Multiple destination devices are best handled as separate transmission lines, each with their own series and shunt terminations. The effective noise at the output, generated by the op amp, can be determined by taking the root sum of the squares of equation (4) and applying the spectral noise values found in the Typical Performance Curve graph section. This applies to noise from the op amp only. Note that both the noise figure (NF) and the equivalent input offset voltages improve as the closed loop gain increases (by keeping RFB fixed and reducing RFF with RN = 0Ω). INCREASING BANDWIDTH AT HIGH GAINS The closed-loop bandwidth can be extended at high gains by reducing the value of the feedback resistor RFB (see Equation 3). This bandwidth reduction is caused by the feedback current being split between RS and RFF (refer to Figure 1). As the gain increases (for a fixed RFB), more feedback current is shunted through RFF, which reduces closed-loop bandwidth. CIRCUIT LAYOUT AND BASIC OPERATION Achieving optimum performance with a high frequency amplifier like the OPA2658 requires careful attention to layout parasitics and selection of external components. Recommendations for PC board layout and component selection include: a) Minimize parasitic capacitance to any ac ground for all of the signal I/O pins. Parasitic capacitance on the output and inverting input pins can cause instability; on the noninverting input it can react with the source impedance to cause unintentional bandlimiting. To reduce unwanted capacitance, a window around the signal I/O pins should be opened in all of the ground and power planes. Otherwise, ground and power planes should be unbroken elsewhere on the board. b) Minimize the distance (< 0.25") from the two power pins to high frequency 0.1µF decoupling capacitors. At the pins, the ground and power plane layout should not be in close proximity to the signal I/O pins. Avoid narrow power and ground traces to minimize inductance between the pins and the decoupling capacitors. Larger (2.2µF to 6.8µF) decoupling capacitors, effective at lower frequencies, should also be used. These may be placed somewhat farther from the device and may be shared among several devices in the same area of the PC board. If the 6dB attenuation loss of a doubly terminated line is unacceptable, a long trace can be series-terminated at the source end only. This will help isolate the line capacitance from the op amp output, but will not preserve signal integrity as well as a doubly terminated line. If the shunt impedance at the destination end is finite, there will be some signal attenuation due to the voltage divider formed by the series and shunt impedances. c) Careful selection and placement of external components will preserve the high frequency performance of the OPA2658. Resistors should be a very low reactance type. Surface mount resistors work best and allow a tighter overall layout. Metal film or carbon composition axially-leaded resistors can also provide good high frequency performance. Again, keep their leads as short as possible. Never use wirewound type resistors in a high frequency application. Since the output pin and the inverting input pin are most sensitive to parasitic capacitance, always position the feedback and series output resistor, if any, as close as possible to the package pins. Other network components, such as noninverting input termination resistors, should also be placed close to the package. e) Socketing a high speed part like the OPA2658 is not recommended. The additional lead length and pin-to-pin capacitance introduced by the socket creates an extremely troublesome parasitic network which can make it almost impossible to achieve a smooth, stable response. Best results are obtained by soldering the part onto the board. If socketing for the DIP package is desired, high frequency flush mount pins (e.g., McKenzie Technology #710C) can give good results. ® 9 OPA2658 SUPPLY VOLTAGES The OPA2658 is nominally specified for operation using ±5V power supplies. A 10% tolerance on the supplies, or an ECL –5.2V for the negative supply, is within the maximum specified total supply voltage of 11V. Higher supply voltages can break down internal junctions possibly leading to catastrophic failure. Single supply operation is possible as long as common mode voltage constraints are observed. The common mode input and output voltage specifications can be interpreted as a required headroom to the supply voltage. Observing this input and output headroom requirement will allow non-standard or single supply operation. Figure 3 shows one approach to single-supply operation. +VS R VAC Output Impedance (Ω) 100 1 0.1 G = +2 0.01 0.001 10k 100k 1M 10M 100M Frequency (Hz) FIGURE 4. Closed-Loop Output Impedance vs Frequency. +VS VS 2 10 VOUT = 1/2 OPA2658 OPA2658 maintains very low closed-loop output impedance over frequency. Closed-loop output impedance increases with frequency since loop gain decreases with frequency. VS + AV VAC 2 ROUT THERMAL CONSIDERATIONS R RL The OPA2658 will not require heatsinking under most operating conditions. Maximum desired junction temperature will set a maximum allowed internal power dissipation as described below. In no case should the maximum junction temperature be allowed to exceed 175°C. The total internal power dissipation (PD) is the sum of quiescent (PDQ) and additional power dissipated in the two output stages (PDL1 and PDL2) while delivering load power. Quiescent power is simply the specified no-load supply current for both channels times the total supply voltage across the part. PDL1 and PDL2 will depend on the required output signals and loads. For grounded resistive loads, and equal bipolar supplies, they would be at a maximum when the outputs are fixed at a voltage equal to 1/2 either supply voltage. Under this condition, PDL1 = VS2/(4•RL1) where RL1 includes feedback network loading. P DL2 is calculated the same way. 402Ω 402Ω FIGURE 3. Single Supply Operation. ESD PROTECTION ESD static damage has been well recognized for MOSFET devices, but any semiconductor device deserves protection from this potentially damaging source. This is particularly true for very high speed, fine geometry processes. ESD static damage can cause subtle changes in amplifier input characteristics without necessarily destroying the device. In precision operational amplifiers, this may cause a noticeable degradation of offset voltage and drift. Therefore, static protection is strongly recommended when handling the OPA2658. Note that it is the power in the output stages, and not into the loads, that determines internal power dissipation. Operating junction temperature (TJ) is given by TA + PD θJA, where TA is the ambient temperature. As an example, compute the maximum TJ for an OPA2658U where both op amps are at G = +2, RL = 100Ω, RFB = 402Ω, ±VS = ±5V, and at the specified maximum TA = +85°C. This gives: OUTPUT DRIVE CAPABILITY The OPA2658 has been optimized to drive 75Ω and 100Ω resistive loads. The device can drive 2Vp-p into a 75Ω load. This high-output drive capability makes the OPA2658 an ideal choice for a wide range of RF, IF, and video applications. In many cases, additional buffer amplifiers are unneeded. P DQ = (10V •17mA ) = 170mW P DL1 = P DL2 = Many demanding high-speed applications such as ADC/DAC buffers require op amps with low wideband output impedance. For example, low output impedance is essential when driving the signal-dependent capacitances at the inputs of flash A/D converters. As shown in Figure 4, the 4 • (100Ω || 804Ω ) = 70mW P D = 170mW + 2 ( 70mW ) = 310mW T J = 85° C + 0.310W •125° C / W = 124° C ® OPA2658 (5V )2 10 CAPACITIVE LOADS The OPA2658’s output stage has been optimized to drive low resistive loads. Capacitive loads, however, will decrease the amplifier’s phase margin which may cause high frequency peaking or oscillations. Capacitive loads greater than 5pF should be buffered by connecting a small resistance, usually 10Ω to 35Ω, in series with the output as shown in Figure 5. This is particularly important when driving high capacitance loads such as flash A/D converters. In general, capacitive loads should be minimized for optimum high frequency performance. Coax lines can be driven if the cable is properly terminated. The capacitance of coax cable (29pF/foot for RG-58) will not load the amplifier when the coaxial cable or transmission line is terminated with its characteristic impedance. 402Ω 5MHz HARMONIC DISTORTION vs LOAD RESISTANCE (G = +2) –55 Harmonic Distortion (dBc) 402Ω tone, third-order spurious plot shown in Figure 7 indicates how far below these two equal power, closely spaced, tones the intermodulation spurious will be. The single tone power is at a matched 50Ω load. The unique design of the OPA2658 provides much greater spurious free range than what a twotone third-order intermodulation intercept specification would predict. This can be seen in Figure 7 as the spurious free range actually increases at the higher output power levels. 10Ω to 35Ω 1/2 OPA2658 RS –60 G = +2, VO = 2Vp-p, fO = 5MHz –65 3fO –70 –75 2fO –80 –85 10 50Ω RL 100 1k Load Resistance (Ω) CL FIGURE 6. 5MHz Harmonic Distortion vs Load Resistance. FIGURE 5. Driving Capacitive Loads. TWO TONE, THIRD-ORDER SPURIOUS LEVELS –65 Third-Order Spurious Level (dBc) COMPENSATION The OPA2658 is internally compensated and is stable in unity gain with a phase margin of approximately 62°, and approximately 64° in a gain of +2V/V when used with the recommended feedback resistor value. Frequency response for other gains are shown in the Typical Performance Curves. The high-frequency response of the OPA2658 in a good layout is very flat with frequency. 20MHz –70 –75 10MHz 5MHz –80 –85 –90 DISTORTION –18 –16 –14 –12 –10 The OPA2658’s Harmonic Distortion characteristics into a 100Ω load are shown versus frequency and power output in the Typical Performance Curves. Distortion can be further improved by increasing the load resistance as illustrated in Figure 6. Remember to include the contribution of the feedback resistance when calculating the effective load resistance seen by the amplifier. –8 –6 –4 –2 0 2 4 Single Tone Power (dBm) FIGURE 7. Third-Order Intercept Point vs Frequency. CROSSTALK Crosstalk is the undesired result of the signal of one channel mixing with and reproducing itself in the output of the other channel. Crosstalk occurs in most multichannel integrated circuits. In dual devices, the effect of crosstalk is measured by driving one channel and observing the output of the undriven channel over various frequencies. The magnitude of this effect is referenced in terms of channel- to-channel isolation and expressed in decibels. "Input referred" points to the fact that there is a direct correlation between gain and crosstalk, therefore at increased gain, crosstalk also increases by a factor equal to that of the gain. Figure 8 illustrates the measured effect of crosstalk in the OPA2658U. Narrowband communication channel requirements will benefit from the OPA2658’s wide bandwidth and low intermodulation distortion on low quiescent power. If output signal power at two closely spaced frequencies is required, third-order nonlinearities in any amplifier will cause spurious power at frequencies very near the two fundamental frequencies. If the two test frequencies, f1 and f2, are specified in terms of average and delta frequency, fO = (f1 + f2)/2 and ∆f = f2 – f1, the two, third-order, close-in spurious tones will appear at fO ±3 • ∆f. The two ® 11 OPA2658 10 0 G = +2 Crosstalk (dB) –10 75Ω 75Ω –20 OPA2658 –30 –40 75Ω 402Ω –50 75Ω –60 402Ω –70 TEK TSG 130A –80 TEK VM700A –90 1M 10M 100M 1G Frequency (MHz) FIGURE 8. Channel-to-Channel Crosstalk. FIGURE 9. Configuration for Testing Differential Gain/Phase. DIFFERENTIAL GAIN AND PHASE Differential Gain (dG) and Differential Phase (dP) are among the more important specifications for video applications. dG is defined as the percent change in closed-loop gain over a specified change in output voltage level. dP is defined as the change in degrees of the closed-loop phase over the same output voltage change. Both dG and dP are specified at the NTSC sub-carrier frequency of 3.58MHz and the PAL subcarrier of 4.43MHz. All NTSC measurements were performed using a Tektronix model VM700A Video Measurement Set. SPICE MODELS Computer simulation using SPICE is often useful when analyzing the performance of analog circuits and systems. This is particularly true for Video and RF amplifier circuits where parasitic capacitance and inductance can have a major effect on circuit performance. SPICE models are available on a disk from the Burr-Brown Applications Department. DEMONSTRATION BOARDS Demonstration boards are available for each OPA2658 package style. These boards implement a very low parasitic layout that will produce the excellent frequency and pulse responses shown in the Typical Performance Curves. For each package style, the recommended demonstration board is: dG/dP of the OPA2658 were measured with the amplifier in a gain of +2V/V with 75Ω input impedance and the output back-terminated in 75Ω. The input signal selected from the generator was a 0V to 1.4V modulated ramp with sync pulse. With these conditions the test circuit shown in Figure 9 delivered a 100IRE modulated ramp to the 75Ω input of the video analyzer. The signal averaging feature of the analyzer was used to establish a reference against which the performance of the amplifier was measured. Signal averaging was also used to measure the dg and dp of the test signal in order to eliminate the generator’s contribution to measured amplifier performance. Typical performance of the OPA2658 is 0.025% differential gain and 0.02° differential phase to both NTSC and PAL standards. DEMONSTRATION BOARD DEM-OPA265xP PACKAGE PRODUCT 8-Pin DIP OPA2658P DEM-OPA265xU SO-8 OPA2658U OPA2658UB DEM-OPA26xxE MSOP-8 OPA2658E Contact your local Burr-Brown sales office or distributor to order demonstration boards. TYPICAL APPLICATION 402Ω 402Ω 75Ω Transmission Line 75Ω 1/2 OPA2658 V OUT Video Input 75Ω 75Ω FIGURE 10. Low Distortion Video Amplifier. ® OPA2658 12 R12 J5 R13 –InB R11 C3 1µF R16 1 +5V 2 C1 0.1µF GND P1 6 R9 J4 5 +InB R8 7 R14 1 R1 J6 OutB R10 R3 J2 8 1/2 OPA2658 R4 –InA R2 R15 2 R6 J3 3 +InA 1/2 OPA2658 4 J1 OutA 1 R5 R7 C2 0.1µF GND 2 –5V P2 C4 1µF FIGURE 11. Circuit Detail For the DEM-OPA265xP Demonstration Board. DEM-OPA265xP Board Layout (A) (B) (C) (D) FIGURE 12a. Board Silkscreen (Bottom). 12b. Board Silkscreen (Top). 12c. Board Layout (Solder Side). 12d. Board Layout (Layout Side). ® 13 OPA2658