® OPA643 OP OPA 643 A64 OPA 3 658 Wideband Low Distortion, High Gain OPERATIONAL AMPLIFIER FEATURES APPLICATIONS ● LOW DISTORTION: –90dBc at 5MHz ● LOW NOISE: 2.3nV/√Hz ● GAIN-BANDWIDTH PRODUCT: 800MHz ● BASE STATION ADC PREAMP ● ADC/DAC BUFFER AMPLIFIER ● LOW DISTORTION IF AMPLIFIER ● AVAILABLE IN SOT23-5 PACKAGE ● STABLE IN GAINS ≥ 3 ● HIGH SLEW RATE: 1000V/µs ● LOW NOISE, BROADBAND, TRANSIMPEDANCE AMPLIFIER ● LOW NOISE PREAMPLIFIER ● VIDEO AMPLIFICATION ● TEST INSTRUMENTATION ● HIGH OPEN-LOOP GAIN: 95dB ● HIGH OUTPUT CURRENT: ±60mA DESCRIPTION The OPA643 provides a level of speed and dynamic range previously unattainable in a monolithic op amp. Using a de-compensated voltage feedback architecture with two internal gain stages, the OPA643 achieves exceptionally low harmonic distortion over a wide frequency range. The "classic" differential input provides all the familiar benefits of precision op amps, such as bias current cancellation and very low inverting current noise compared with wideband current feedback op amps. High slew rate and open-loop gain, along with low input noise and high output current drive make the OPA643 ideal for very high dynamic range requirements. The high gain bandwidth product for the gain ≥ 3 stable OPA643 makes it particularly suitable for wideband transimpedance amplifiers and moderate gain IF amplifier applications. External compensation techniques may be used to apply the OPA643 at low gains giving exceptionally low distortion and frequency response flatness. Where unity gain stability with comparable distortion performance is required, consider the OPA642. +5V 5kΩ REFT 0.1µF +5V ADS805 Low Gain Compensation 0.1µF 280Ω 2Vp-p 0.1µF 50Ω Analog Input OPA643 47pF 50Ω Source –5V 806Ω 402Ω 1Vp-p 10MHz 12-Bit 20MSPS Measured 80dB SFDR 5kΩ REFB 56.9Ω 2.7pF 0.1µF 14pF High Dynamic Range 20MSPS Digitizer International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111 Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 ® © 1993 Burr-Brown Corporation 1 PDS-1191D Printed in U.S.A. March, 1998 OPA643 SPECIFICATIONS ELECTRICAL At TA = +25°C, VS = ±5V, RL = 100Ω, RF = 402Ω, unless otherwise noted. OPA643P, U, N PARAMETER CONDITIONS OFFSET VOLTAGE Input Offset Voltage Average Drift Power Supply Rejection (PSR) TYP MAX ±4 65 ±2.5 5 90 VCM = 0V 19 VCM = 0V 0.1 30 40 2.0 3.0 VS = ±4.5 to ±5.5V INPUT BIAS CURRENT Input Bias Current Over Specified Temperature Input Offset Current Over Specified Temperature NOISE Input Voltage Noise Noise Density: f > 1MHz Integrated Voltage Noise, BW = 100Hz to 100MHz Input Bias Current Noise Current Noise Density, f > 1MHz INPUT VOLTAGE RANGE Common-Mode Input Range Over Specified Temperature Common-Mode Rejection (CMR) VCM = ±0.5V ±2.75 ±2.5 65 INPUT IMPEDANCE Differential Common-Mode OPEN-LOOP GAIN Open-Loop Voltage Gain (AOL) Over Specified Temperature FREQUENCY RESPONSE Closed-Loop Bandwidth Gain Bandwidth Product (GBP) Slew Rate(1) At Minimum Specified Temperature Settling Time: 0.01% 0.1% 1% Spurious Free Dynamic Range (SFDR) Differential Gain Error at 3.58MHz Differential Phase Error at 3.58MHz OUTPUT Voltage Output Over Specified Temperature Voltage Output, +25°C Over Specified Temperature Current Output, +25°C Over Specified Temperature Closed-Loop Output Resistance POWER SUPPLY Specified Operating Voltage Operating Voltage Range Quiescent Current Over Specified Temperature TEMPERATURE RANGE Specification: P, U, N Thermal Resistance P, PB 8-Pin DIP U, UB 8-Pin SO-8 N, NB 5-Pin SOT23-5 MIN TYP MAX UNITS ±1.5 70 ±0.5 3 ✻ mV µV/°C dB ✻ ✻ ✻ ✻ ✻ µA µA µA µA ✻ 2.3 23 ✻ ✻ nV/√Hz µVrms 2.5 ✻ pA/√Hz ✻ 92 V V dB ✻ ✻ kΩ || pF kΩ || pF ✻ dB dB ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ±3.0 ✻ ✻ 80 85 7 || 2.5 630 || 1.3 VO = ±2V, RL = 100Ω VO = ±2V, RL = 100Ω 82 80 Gain = +5V/V Gain = +10V/V Gain = +20V/V 95 87 80 G = +5, 2V Step G = +5, 2V Step G = +5, 2V Step G = +5, 2V Step G = +5, 2V Step G = +5, f = 5MHz VO = 2Vp-p, RL = 500Ω G = +5V/V, VO = 0V to 1.4V, RL = 150Ω G = +5V/V, VO = 0V to 1.4V, RL = 150Ω 200 85 40 800 1000 920 21 16.5 7.5 90 95 MHz MHz MHz MHz V/µs V/µs ns ns ns dBc 0.005 0.015 ✻ ✻ % degrees No Load ±3.25 ✻ V V V V mA mA Ω ±3.0 RL = 100Ω ±2.5 ±40 ±35 0.1MHz, G = +5V/V TMIN to TMAX Ambient θJA, Junction to Ambient ✻ ±2.75 ✻ ✻ ±50 ±40 ±60 ±4.5 ±5 ±20 –40 100 125 150 NOTE: (1) Slew rate is rate of change from 10% to 90% of output voltage step. ® 2 ±65 ✻ 0.055 ✻ Specifications same as OPA643P, U, N. OPA643 OPA643PB, UB, NB MIN ✻ ±5.5 ±25 ±26 ✻ ±16 +85 ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ V V mA mA ✻ °C °C/W °C/W °C/W ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION Power Supply (±VS) ..................................................................... ±6.0VDC Internal Power Dissipation(1) .................................. See Thermal Analysis Differential Input Voltage .................................................................. ±1.2V Input Voltage Range ............................................................................ ±VS Storage Temperature Range: P, PB, U, UB, N, NB ..... –40°C to +125°C Lead Temperature (soldering, 10s) .............................................. +300°C (soldering, SO-8 3s) ....................................... +260°C Junction Temperature (TJ ) ............................................................ +175°C NOTE: (1) Packages must be derated based on specified θ must be observed. JA. Top View DIP/SO-8 NC 1 8 +VS2(1) Inverting Input 2 7 +VS1 Non-Inverting Input 3 6 Output –VS1 4 5 –VS2(1) Maximum TJ SOT23-5 ELECTROSTATIC DISCHARGE SENSITIVITY Electrostatic discharge can cause damage ranging from performance degradation to complete device failure. Burr-Brown Corporation recommends that all integrated circuits be handled and stored using appropriate ESD protection methods. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet published specifications. Output 1 –VS 2 Non-Inverting Input 3 5 +VS 4 Inverting Input NOTE: (1) Making use of all four power supply pins is highly recommended, although not required. Using these four pins, instead of just pins 4 and 7, will lower the power supply impedance improving distortion. PACKAGE/ORDERING INFORMATION PRODUCT PACKAGE PACKAGE DRAWING NUMBER(1) OPA643U OPA643UB OPA643N SO-8 Surface Mount SO-8 Surface Mount 5-pin SOT23-5 182 182 331 –40°C to +85°C –40°C to +85°C –40°C to +85°C OPA643U OPA643UB A43 OPA643NB 5-pin SOT23-5 331 –40°C to +85°C A43B OPA643P OPA643PB 8-Pin Plastic DIP 8-Pin Plastic DIP 006 006 –40°C to +85°C –40°C to +85°C OPA643P OPA643PB TEMPERATURE RANGE PACKAGE MARKING(2) ORDERING NUMBER(3) OPA643U OPA643UB OPA643N-250 OPA643N-3k OPA643NB-250 OPA643NB-3k OPA643P OPA643PB NOTES: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. (2) The “B” grade of the SO-8 and DIP packages will be marked with a “B” by pin 8. The “B” grade of the SOT23-5 will be marked with a “B” near pins 3 and 4. (3) The SOT23-5 is only available on a 7" tape and reel (e.g. ordering 250 pieces of “OPA643N-250” will get a single 250 piece tape and reel. Ordering 3000 pieces of “OPA643N-3k” will get a single 3000 piece tape and reel). Please refer to Appendix B of Burr-Brown IC Data Book for detailed Tape and Reel Mechanical information. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. ® 3 OPA643 TYPICAL PERFORMANCE CURVES At TA = +25°C, VS = ±5V, RL = 100Ω, RF = 402Ω, unless otherwise noted SMALL SIGNAL FREQUENCY RESPONSE VO = 0.1Vp-p 3 0 VO = 1Vp-p 14 G = +10 –3 –6 –9 –12 G = +20 –15 G = +5 17 G = +5 Gain (3dB/div) Normalized Gain (3dB/div) LARGE SIGNAL FREQUENCY RESPONSE 20 6 11 VO = 2Vp-p 8 5 VO = 4Vp-p 2 –1 –4 –18 G = +50 –21 –24 0.5MHz 10MHz –7 100MHz –10 0.5MHz 500MHz 10MHz Frequency 500MHz LARGE SIGNAL PULSE RESPONSE 200 2.0 160 1.6 Output Voltage (400mV/div) Output Voltage (40mV/div) SMALL SIGNAL PULSE RESPONSE 120 80 40 0 –40 –80 –120 –160 1.2 0.8 0.4 0 –0.4 –0.8 –1.2 –1.4 –200 –2.0 Time (5ns/div) Time (5ns/div) RS vs CAPACITIVE LOAD FREQUENCY RESPONSE vs CAPACITIVE LOAD 60 Gain to Capacitive Load (3dB/div) 23 50 40 RS (Ω) 100MHz Frequency 30 20 10 0 20 G = +5 CL = 10pF 17 CL = 22pF 14 11 RS VIN 8 OPA643 5 402Ω VO CL 1kΩ 2 –1 100Ω (1kΩ is optional) –4 CL = 100pF –7 1 10 100 0 Capacitive Load (pF) ® OPA643 100MHz Frequency (20MHz/div) 4 CL = 47pF 200MHz TYPICAL PERFORMANCE CURVES (CONT) At TA = +25°C, VS = ±5V, RL = 100Ω, RF = 402Ω, unless otherwise noted. 5MHz 3RD HARMONIC DISTORTION 5MHz 2ND HARMONIC DISTORTION –70 –70 G = +5 RL = 200Ω 3rd Harmonic Distortion (dBc) 2nd Harmonic Distortion (dBc) G = +5 –75 –80 RL = 100Ω –85 –90 –95 –75 –80 –85 –90 RL = 200Ω –95 RL = 500Ω RL = 500Ω –100 –100 0.1 1 0.1 10 10MHz 2ND HARMONIC DISTORTION 10MHz 3RD HARMONIC DISTORTION –60 –60 G = +5 –65 3rd Harmonic Distortion (dBc) G = +5 2nd Harmonic Distortion (dBc) 10 Output Voltage Swing (Vp-p) Output Voltage Swing (Vp-p) RL = 100Ω –70 RL = 200Ω –75 –80 RL = 500Ω –85 –65 –70 –75 –80 RL = 200Ω –85 RL = 500Ω –90 –90 0.1 1 10 0.1 Output Voltage Swing (Vp-p) RL = 100Ω 1 10 Output Voltage Swing (Vp-p) 20MHz 3RD HARMONIC DISTORTION 20MHz 2ND HARMONIC DISTORTION –60 –60 G = +5 3rd Harmonic Distortion (dBc) G = +5 2nd Harmonic Distortion (dBc) RL = 100Ω 1 –65 RL = 100Ω –70 –75 RL = 200Ω RL = 500Ω –80 –85 –65 –70 –75 RL = 200Ω –80 RL = 500Ω –85 RL = 100Ω –90 –90 0.1 1 0.1 10 1 10 Output Voltage Swing (Vp-p) Output Voltage Swing (Vp-p) ® 5 OPA643 TYPICAL PERFORMANCE CURVES (CONT) At TA = +25°C, VS = ±5V, RL = 100Ω, RF = 402Ω, unless otherwise noted. 3RD HARMONIC DISTORTION vs FREQUENCY 2ND HARMONIC DISTORTION vs FREQUENCY –40 –40 VO = 2Vp-p 3rd Harmonic Distortion (dBc) 2nd Harmonic Distortion (dBc) VO = 2Vp-p –50 G = 20 –60 G = 10 –70 G=5 –80 –90 –50 –60 G = 20 –70 –80 G = 10 –90 G=5 –100 –100 0.1 1 10 0.1 20 1 10 Frequency (MHz) Frequency (MHz) INPUT VOLTAGE AND CURRENT NOISE DENSITY TWO-TONE, THIRD ORDER INTERMODULATION INTERCEPT 100 20 55 10 Current Noise Voltage Noise Intercept (dBm) Current Noise pA/√Hz Voltage Noise nV/√Hz 50 2.5pA/√Hz 45 40 Pi 50Ω 50Ω 35 PO 50Ω 2.3nV/√Hz 402Ω 30 1 100Ω 25 102 103 104 105 106 107 0 5 Differential Gain Error (%) OPEN-LOOP GAIN AND PHASE 0 –30 80 –60 70 –90 60 –120 50 –150 40 –180 30 –210 20 –240 10 –270 0 –300 103 104 105 106 107 108 109 Frequency (Hz) ® OPA643 15 20 25 30 35 40 45 50 0.004 0.002 0.000 –0.002 –0.004 –0.006 0 0.7 1.4 DC Offset (V) Differential Phase Error (°) 90 Open-Loop Phase (30°/div) 100 102 10 Frequency (MHz) Frequency (Hz) Open-Loop Gain (dB) OPA643 6 0.015 0.010 0.005 0.000 0 0.7 DC Offset (V) 1.4 TYPICAL PERFORMANCE CURVES (CONT) At TA = +25°C, VS = ±5V, RL = 100Ω, RF = 402Ω, unless otherwise noted. CMR AND PSR vs FREQUENCY CLOSED-LOOP OUTPUT IMPEDANCE 100 PSR G = +5 10 CMR 80 Output Impedance (Ω) Rejection Ratio (dB) 90 70 60 50 40 1 0.10 0.01 30 0.001 20 102 103 104 105 106 107 108 0 1 10 100 Frequency (MHz) DIFFERENTIAL AND COMMON-MODE INPUT IMPEDANCE COMMON-MODE REJECTION vs INPUT COMMON-MODE VOLTAGE 1000 500 90 Common-Mode Rejection (dB) Common-Mode Input Impedance (kΩ) 0.1 Frequency (Hz) 100 Differential Input 10 1 80 70 60 50 102 103 104 105 106 107 108 –5 –4 –3 –2 –1 0 1 2 3 4 Frequency (Hz) Common-Mode Voltage AOL, PSR AND CMR vs TEMPERATURE OUTPUT AND QUIESCENT CURRENT vs TEMPERATURE 110 80 5 IO+ 100 Output Current (mA) AOL, PSR, CMR (dB) 70 AOL +PSR 90 –PSR CMR 60 IO– 50 40 30 ICC 20 10 80 0 –75 –50 –25 0 25 50 75 100 125 –50 Temperature (°C) –25 0 25 50 75 100 125 Ambient Temperature (°C) ® 7 OPA643 APPLICATIONS INFORMATION BUFFERING HIGH PERFORMANCE ADC’S To achieve full performance from a high dynamic range A/D converter, considerable care must be exercised in the design of the input amplifier interface circuit. The example circuit on the front page shows a typical AC-coupled interface to a very high dynamic range converter. This circuit uses a new external compensation technique which stabilizes the OPA643 for low signal gain, while maintaining the high gain bandwidth, fast slew rate and improved distortion performance of the decompensated architecture. Testing shows that a high loop gain and flat response are maintained through the Nyquist frequency on this circuit using the ADS805 giving very high SFDR performance. Above Nyquist, the loop gain is rolled off sharply to lower the crossover frequency, and finally additional lead is introduced at crossover to maintain good phase margin. In general, this loop gain shaping technique allows the use of high gain bandwidth, decompensated op amps to achieve better dynamic performance in low signal gain applications. Refer to the section on Low Gain Operation for further information. TYPICAL APPLICATION AND CHARACTERIZATION CIRCUIT The OPA643’s combination of speed and dynamic range is easily achieved in a wide variety of application circuits, providing that simple guidelines common to all high speed amplifiers are observed. For example, good power supply decoupling, as shown in Figure 1, is essential to achieve the lowest possible harmonic distortion and smooth frequency response. Careful PC board layout and component selection will maximize the performance of the OPA643 in all applications, as discussed in the remaining sections of this data sheet. Figure 1 shows the gain of +5 configuration used as the basis for most of the Typical Performance Curves. Most of the curves were characterized using signal sources with 50Ω driving impedance, and with measurement equipment presenting 50Ω load impedance. In Figure 1, the 50Ω shunt resistor at the VI terminal matches the source impedance of the test generator, while the 50Ω series resistor at the VO terminal provides a matching resistor for the measurement equipment load. Generally, data sheet specifications refer to the voltage swing at the output pin (VO in Figure 1). The total 100Ω load from the series and shunt matching resistors, combined with the 502Ω total feedback network load, presents the OPA643 with an effective output load of approximately 83Ω. The frequency domain digitizer application on the front page allows the signal swing at the output of the OPA643 to be operated at an optimum DC point. Centering the output swing between the supplies is a good starting point, but significant improvement in second-harmonic distortion can be achieved by shifting the output DC point away from ground. A typical signal swing of 2Vp-p, operating at either an optimized or a ground-centered output DC voltage, is then level shifted through the blocking capacitor to a DC reference level at the converter input. This reference voltage is created by a well decoupled resistive divider off the converter’s internal reference voltages. To have negligible effect on the rated spurious-free dynamic range (SFDR) of the converter, the amplifier’s SFDR should be at least 10dB greater. In the front page example, the insertion of the OPA643 has an unmeasurable effect on the distortion of the 20MSPS ADS805, which achieves 80dB SFDR at a 10MHz Nyquist input signal. +VS +5V 2.2µF + 0.1µF 50Ω Source VI 0.1µF 3 8 50Ω RT To deliver the lowest possible distortion using the 8-pin SO-8 or DIP package, additional 0.1µF power supply decoupling capacitors on pins 5 and 8 are required. These are shown in Figure 1. Although pins 5 and 8 are internally connected to pins 4 and 7 respectively (the standard supply pins for 8-pin op amps), the additional capacitors help to decouple the package lead inductances and decrease the second-harmonic distortion for a 5MHz fundamental by approximately 4dB. The much shorter bond wires and supply leads of the SOT23-5 package give the best distortion performance while requiring only two power supply connections. 7 6 OPA643 VO 50Ω 50Ω Load 5 0.1µF 2 4 0.1µF RF 402Ω RG 100Ω 2.2µF + Gain, –5V –VS VO VI =1+ Successful application to ADC buffering requires a careful selection of the series resistor at the output of the OPA643, along with the additional shunt capacitor at the ADC input. To some extent, selection of this RC network will be determined empirically for each model of converter. Many high performance CMOS ADC’s, like the ADS805, perform better with an additional capacitor to ground on the input RF RG FIGURE 1. Gain of +5, High Frequency Application and Characterization Circuit (P or U Package). ® OPA643 8 pin. This capacitor provides a low source impedance for the transient currents produced by the sampling process. Improved SFDR is obtained by adding the capacitor, whose value is often recommended in the converter data sheet. The external capacitor, in combination with the built-in capacitance of the A/D input, presents a significant capacitive load to the OPA643. Without a series isolation resistor, the result can be peaking and possibly oscillation in the amplifier. Refer to the plot of “RS vs Capacitive Load” in the Typical Performance Curves to obtain a good starting value for the series resistor. The values shown in this curve will ensure a flat frequency response at the input of the ADC. Increasing the external capacitor value will allow either the series resistor to be reduced, or, keeping this resistor fixed, will bandlimit the signal and reduce high frequency noise to the input of the converter. The input signal and the gain resistor are AC coupled through the 0.1µF blocking capacitors. This holds the DC input and output operating point at ground independent of source impedance and gain setting. The RG value shown in Figure 2 (144Ω) sets the gain to the matched load at 12dB. Using standard 1% tolerance resistors for RF and RG will hold the gain to a ±0.2dB tolerance. This example will give a –3dB bandwidth of approximately 100MHz while maintaining gain flatness within 1dB through 50MHz. For narrowband IF’s in the 21.4MHz region, this configuration of the OPA643 will show a third-order intercept of 40dBm while dissipating only 200mW (23dBm) power from ±5V supplies. PHOTODIODE TRANSIMPEDANCE AMPLIFIER High Gain Bandwidth Product (GBP) and low input voltage and current noise make the OPA643 an ideal wideband transimpedance amplifier for low to moderate gains. Note that unity gain stability is not required for application as a transimpedance amplifier. Figure 3 shows an example photodiode amplifier circuit. The key parameters of this design are the estimated diode capacitance (CD) at the applied DC reverse bias voltage (–VB ), the desired transimpedance gain (RF), and the GBP for the OPA643 (800MHz). With these three variables set (and adding the OPA643’s parasitic input capacitance to the value of CD to get CS), the feedback capacitor value (CF) may be chosen to control the transimpedance frequency response. WIDE DYNAMIC RANGE IF AMPLIFIER The OPA643 offers an attractive alternative to standard fixed gain IF amplifier stages. Narrowband systems will benefit from the exceptionally high two tone third-order intermodulation intercept as shown in the Typical Performance Curves. Op amps with high open-loop gain, like the OPA643, provide an intercept that decreases with frequency along with the loop gain. The OPA643’s intercept is > 25dBm up to 50MHz but improves to > 50dBm as the operating frequency is reduced below 10MHz. Broadband systems will also benefit from the very low even order harmonics and intermodulation components produced by the OPA643. Compared to standard fixed gain IF amplifiers, the OPA643 operating at IF’s below 50MHz provides much higher intercepts for its quiescent power dissipation (200mW), superior gain accuracy, higher reverse isolation, and lower I/O return loss. Noise figure for the OPA643 will be higher than alternative fixed gain stages. If the application comes late in the amplifier chain with significant gain in prior stages, this higher noise figure will be acceptable. Figure 2 shows an example non-inverting configuration for the OPA643 used as an IF amplifier. +5V Supply Decoupling Not Shown OPA643 VO = ID RF RF 10kΩ λ ID CD 20pF –5V CF 0.8pF –VB +5V 50Ω Source 0.1µF 52.3Ω FIGURE 3. Wideband, Low Noise, Transimpedance Amplifier. Supply Decoupling Not Shown 50Ω PI 1kΩ OPA643 PO To achieve a maximally flat second-order Butterworth frequency response, the feedback pole should be set to: 50Ω Load RF 1kΩ 1/(2πRFCF) = √(GBP/(4πRFCS)) –5V RG 144Ω Gain = PO PI = 20log 1/2 (1+ RF RG ) Adding the OPA643’s common-mode and differential mode input capacitances (1.3 + 2.5)pF to the 20pF diode source capacitance of Figure 3, and targeting a 10kΩ transimpedance gain using the 800MHz GBP for the OPA643, the required feedback pole frequency is 16.4MHz. This will require a total feedback capacitance of 1.0pF. Typical surface mount resistors have a parasitic capacitance of 0.2pF, leaving the dB = 12dB with values shown 0.1µF FIGURE 2. Wide Dynamic Range IF Amplifier. ® 9 OPA643 A good rule of thumb is to target the parallel combination of RF and RG (Figure 1) to be less than about 200Ω. The combined impedance RF RG interacts with the inverting input capacitance, placing an additional pole in the feedback network and thus a zero in the forward response. Assuming a 3pF total parasitic on the inverting node, holding RF RG < 200Ω will keep this pole above 250MHz. By itself, this constraint implies that the feedback resistor RF can increase to several kΩ at high gains. This is acceptable as long as the pole formed by RF and any parasitic capacitance appearing in parallel with it is kept out of the frequency range of interest. The exception to this is in wideband transimpedance applications as described earlier. There, a feedback pole is used to compensate for the zero formed by the input capacitance and the feedback resistor. required 0.8pF value shown in Figure 3 to get the required feedback pole. This will set the –3dB bandwidth according to: F–3dB ≅ √(GBP/2πRFCS) Hz The example of Figure 3 will give approximately 23MHz flat bandwidth using the 0.8pF feedback compensation. WIDEBAND INVERTING SUMMING AMPLIFIER One common application for a wideband op amp like the OPA643 is to sum a number of signal sources together. Figure 4 shows the inverting summing configuration that is most often used. This circuit offers the benefit that each input sees an input impedance set only by its individual input resistor, since the summing junction (inverting op amp node) is a virtual ground. Each input is non-interactive with every other. However, the bandwidth from any input to the summed output is set by the op amp noise gain (NG), equal to the non-inverting voltage gain. So, even though each inverting channel may have a low gain to the output (like the –1 shown in Figure 4), the overall noise gain will set the frequency response and the loop stability. The non-inverting gain for Figure 4 is equal to +5 which will give a 200MHz bandwidth at a gain of –1 for each of the input signals. In the inverting configuration, an additional design contraint must be considered. RG becomes the input resistor and therefore the load impedance to the driving source. If impedance matching is desired, RG may be set equal to the required termination value. However, at low inverting gains, the resulting feedback resistor value can present a significant load to the amplifier output. For example, an inverting gain of –4 (noise gain of 5) with a 50Ω input matching resistor (= RG) would require a 200Ω feedback resistor, which would increase output loading in parallel with the external load. To decrease the added loading, it would be preferable to increase both the RF and RG values, and then achieve the input matching impedance with a third resistor to ground at the input. The total input impedance becomes the parallel combination of RG and this additional shunt input resistor. +5V Supply Decoupling Not Shown 0.1µF 81.6Ω OPA643 VO = – (V1 + V2 + V3 + V4) BANDWIDTH VS GAIN Voltage feedback op amps exhibit decreasing closed-loop bandwidth as the signal gain is increased. In theory, this relationship is described by the Gain Bandwidth Product (GBP) shown in the Electrical Specifications. Ideally, dividing GBP by the non-inverting signal gain (also called the noise gain, or NG) will predict the closed-loop bandwidth. In practice, this relationship only holds true when the phase margin approaches 90°, as it does in high gain configurations. At low signal gains, most high speed amplifiers will exhibit a more complex response with lower phase margin. The OPA643 is optimized to give a maximally flat frequency response at a gain of +5. Dividing the typical 800MHz gain bandwidth product by the noise gain of 5 would predict a closed-loop bandwidth of 160MHz. However, the actual bandwidth is extended to > 200MHz due to the reduced (< 90°) phase margin at this noise gain. Increasing the gain will increase the phase margin moving the closed-loop bandwidth closer to that predicted by the gain bandwidth product. The 40MHz bandwidth at a gain of +20, shown in the Electrical Specifications, agrees with that predicted using the 800MHz GBP. 402Ω V1 402Ω RF 402Ω V2 402Ω V3 402Ω –5V V4 FIGURE 4. Wideband Inverting Summing Amplifier. OPERATING SUGGESTIONS OPTIMIZING RESISTOR VALUES Since the OPA643 is a voltage feedback op amp, a wide range of resistor values may be used for the feedback and gain setting resistors (RF and RG in Figure 1). The primary limits to these values are set by dynamic range (noise and distortion) and parasitic capacitive considerations. Usually, the feedback resistor value should be between 200Ω and 1kΩ. Below 200Ω, the feedback network will present additional output loading which can degrade the harmonic distortion performance of the OPA643. Above 1kΩ, the typical parasitic capacitance (approximately 0.2pF) across the feedback resistor may cause unintentional band-limiting in the amplifier response. LOW GAIN OPERATION Decreasing the operating gain for the OPA643 from the nominal design point of +5 will decrease the phase margin. ® OPA643 10 gain for the op amp and the noise gain pole, set by 1/RFCF, is placed correctly, a very well controlled second-order low pass frequency response will result. This will increase the Q for the closed-loop poles, peaking up the frequency response and extending the bandwidth. A peaked frequency response will show overshoot and ringing in the pulse response as well as a higher integrated output noise. Operating at a noise gain less than +3 runs the risk of sustained oscillation (loop instability). However, operation at low gains would be desirable to take advantage of the much higher slew rate and lower input noise voltage available in the OPA643, as compared to performance offered by unity gain stable op amps. Numerous external compensation techniques have been suggested for operating a high gain op amp at low gains. Most of these give zero/pole pairs in the closed-loop response that cause long term settling tails in the pulse response and/or phase non-linearity in the frequency response. Figure 5 shows an external compensation method for the non-inverting configuration that does not suffer from these drawbacks. +5V RT 280Ω 0.1µF OPA643 RG 402Ω VO RF 806Ω VI CS 12.6pF CF 1.9pF –5V FIGURE 6. Broadband Low Gain Inverting External Compensation. +5V 50Ω Source RT 50Ω RI 133Ω OPA643 VO To choose the values for both CS and CF, two parameters and only three equations need to be solved. The first parameter is the target high frequency noise gain NG2, which should be greater than the minimum stable gain for the OPA643. Here, a target NG2 of 7.5 will be used. The second parameter is the desired low frequency signal gain, which also sets the low frequency noise gain NG1. To simplify this discussion, we will target a maximally flat second-order low pass Butterworth frequency response (Q = 0.707). The signal gain of –2 shown in Figure 6 will set the low frequency noise gain to NG1 = 1 + RF/RG (= 3 in this example). Then, using only these two gains and the Gain Bandwidth Product (GBP) for the OPA643 (800MHz), the key frequency in the compensation can be determined as: 50Ω RF 402Ω RG 402Ω –5V FIGURE 5. Broadband Low Gain Non-Inverting External Compensation. The RI resistor across the two inputs will increase the noise gain (i.e. decrease the loop gain) without changing the signal gain. This approach will retain the full slew rate to the output but will give up some of the low noise benefit of the OPA643. Assuming a low source impedance, set RI so that 1+RF/(RG || RI) is ≥ +3. ZO = GBP NG12 NG1 NG1 1 – – 1– 2 NG 2 NG 2 Physically, this Z0 (13.6MHz for the values shown in Figure 6) is set by 1/(2π • RF(CF + CS)) and is the frequency at which the rising portion of the noise gain would intersect unity gain if projected back to 0dB gain. The actual zero in the noise gain occurs at NG1 • Z0 and the pole in the noise gain occurs at NG2 • Z0. Since GBP is expressed in Hz, multiply Z0 by 2π and use this to get CF by solving: Where a low gain is desired, and inverting operation is acceptable, a new external compensation technique may be used to retain the full slew rate and noise benefits of the OPA643 while maintaining the increased loop gain and the associated improvement in distortion offered by the decompensated architecture. This technique shapes the loop gain for good stability while giving an easily controlled second-order low pass frequency response. Figure 6 shows this circuit (the same amplifier circuit as shown on the front page). Considering only the noise gain for the circuit of Figure 6, the low frequency noise gain, (NG1) will be set by the resistor ratios while the high frequency noise gain (NG2) will be set by the capacitor ratios. The capacitor values set both the transition frequencies and the high frequency noise gain. If this noise gain, determined by NG2 = 1+ CS/CF, is set to a value greater than the recommended minimum stable CF = 1 2π • R F Z O NG 2 Finally, since CS and CF set the high frequency noise gain, determine CS by: C S = ( NG 2 – 1) C F The resulting closed-loop bandwidth will be approximately equal to: F –3dB ≅ Z O GBP ® 11 OPA643 phase margin. This issue has become a popular topic of application notes and articles, and several external solutions to this problem have been suggested. When the primary considerations are frequency response flatness, pulse response fidelity and/or distortion, the simplest and most effective solution is to isolate this capacitive load from the feedback loop by inserting a series isolation resistor between the output and the capacitive load. This does not eliminate the pole from the loop response, but rather shifts it and adds a zero at a higher frequency. The additional zero acts to cancel the phase lag from the capacitive load pole, increasing the phase margin and improving stability. For the values shown in Figure 6, the F–3dB will be approximately 105MHz. This is less than that predicted by simply dividing the GBP product by NG1. The compensation network controls the bandwidth to a lower value while providing full slew rate and exceptional distortion performance due to increased loop gain at frequencies below NG1 • Z0. The capacitor values shown in Figure 6 are calculated for NG1 = 3 and NG2 = 7.5 with no adjustment for parasitics. These differ slightly from the application circuit on the front page, since those have been adjusted for parasitics and to account for the capacitive load (through RS) at the ADC input. The Typical Performance Curves show the recommended series RS vs Capacitive Load and the resulting frequency response at the load. The criterion for setting this resistor is a maximum bandwidth, flat frequency response at the load. Since there is now a passive low pass filter from the output pin to the load capacitor, the response at the output pin itself is typically somewhat peaked, and becomes flat after the rolloff action of the RC network. This is not a concern in most applications, but can cause clipping if the desired signal swing at the load is very close to the amplifier’s swing limit. Such clipping would be most likely to occur for a large signal pulse response where this slight peaking causes an overshoot in the step response at the output pin. OUTPUT VOLTAGE AND CURRENT DRIVE The OPA643 has been optimized to drive the demanding load of a doubly terminated transmission line. When a 50Ω line is driven, a series 50Ω source resistance into the cable and a terminating 50Ω load at the end of the cable are used. Under these conditions, the cable’s impedance will appear resistive over a wide frequency range, and the total effective load on the OPA643 is 100Ω in parallel with the resistance of the feedback network. The specifications show a guaranteed ±2.5V swing over the full temperature range into this 100Ω load—which will then be reduced to a ±1.25V swing at the termination resistor. The guaranteed ±35mA output current over temperature provides adequate current drive margin for this load. Higher voltage swings (and lower distortion) are achievable when driving higher impedance loads. Parasitic capacitive loads greater than 2pF can begin to degrade the performance of the OPA643. Long PC board traces, unmatched cables, and connections to multiple devices can easily exceed 2pF. Always take care to consider this, and add the recommended series resistor as close as possible to the OPA643 output pin (see Board Layout Guidelines). A common IF amplifier specification which describes available output power is the –1dB compression point. This is usually defined at a matched 50Ω load to be the sinusoidal power where the gain has compressed by –1dB vs the gain seen at very low power levels. This compression level is frequency dependent for an op amp, due to both bandwidth and slew rate limitations. For frequencies well within the bandwidth and slew rate limit of the OPA643, the –1dB compression at a matched 50Ω load will be > 13dBm based on the minimum available ±1.25V swing at the load. One common use for the –1dB compression is to predict intermodulation intercept. This is normally 10dB greater than the –1dB compression power for a standard RF amplifier. This simple rule of thumb does NOT apply to the OPA643. The high open loop gain and Class AB output stage of the OPA643 produce a much higher intercept than the –1dB compression would predict, as shown in the Typical Performance Curves. DISTORTION PERFORMANCE The OPA643 is capable of delivering an exceptionally low distortion signal at high frequencies over a wide range of gains. The distortion plots in the Typical Performance Curves show the typical distortion under a wide variety of conditions. Most of these plots are limited to 100dB dynamic range. The OPA643’s distortion does not rise above –90dBc until either the signal level exceeds 0.5V and/or the fundamental frequency exceeds 500kHz. Distortion in the audio band is < –120dBc. Generally, until the fundamental signal reaches very high frequencies or powers, the second harmonic will dominate the distortion with negligible third harmonic component. Focusing then on the second harmonic, increasing the load impedance improves distortion directly. Remember that the total load includes the feedback network—in the noninverting configuration this is sum of RF + RG, while in the inverting configuration it is only RF (Figure 1). Larger output voltage swings lead directly to increased harmonic distortion. A 6dB increase in output voltage swing will generally increase the second harmonic by 12dB and the third harmonic by 18dB. Higher signal gain settings will also increase the second harmonic distortion. A 6dB increase in voltage gain will raise the second and third harmonics by DRIVING CAPACITIVE LOADS One of the most demanding and yet very common load conditions for an op amp is capacitive loading. A high speed, high open-loop gain amplifier, like the OPA643, can be very susceptible to decreased stability and closed-loop response peaking when a capacitive load is placed directly on the output pin. In simple terms, the capacitive load reacts with the open-loop output resistance of the amplifier to introduce an additional pole into the loop and thereby decrease the ® OPA643 12 6dB each, even at constant output power and frequency. This effect is due to the reduction in loop gain which accompanies an increase in signal gain. Finally, distortion grows as the fundamental frequency increases, due to the rolloff in loop gain with frequency. Going the other direction, distortion will improve at lower frequencies until the dominant open loop pole is reached at approximately 8kHz. Starting with the –92dBc second-harmonic for a 1MHz, 2Vp-p fundamental into a 500Ω load at G = +5 (from the Typical Performance Curves), the second-harmonic distortion at 20kHz will be approximately (–92dBc – 20log (1MHz/ 20kHz)) ≅ –126dBc, while the third-order terms will be much lower. The OPA643 has extremely low third-order harmonic distortion. This characteristic leads to the exceptionally high 2-tone third-order intermodulation intercept as shown in the Typical Performance Curves. The intercept curve is defined at the 50Ω load when driven through a 50Ω matching resistor to allow direct comparisons to RF MMIC devices. The matching network attenuates the voltage swing from the output pin to the load by 6dB. If the OPA643 drives directly into the input of a high impedance device such as an ADC, the 6dB attenuation does not exist and the intercept will increase by at least 6dBm. The intercept is used to predict intermodulation spurs for two closely spaced input frequencies. If the two test frequencies, f1 and f2, are specified in terms of average and delta frequency, In most applications the second-harmonic will set the limit to dynamic range. Even order nonlinearity arises from slight asymmetries between the positive and negative halves of the output sinusoid. This asymmetrical nonlinearity comes from such mechanisms as voltage dependent junction capacitances, transistor gain mismatches and imbalanced source impedances looking out of the amplifier power pins. Once a circuit and board layout has been determined, these asymmetries can often be nulled out by adjusting the DC operating point for the signal. An example of such DC trimming is shown in Figure 7. This circuit has a DC coupled inverting signal path to the output pin, providing gain for a small DC offset signal applied to the non-inverting input pin. The output is AC coupled to block off this DC operating point and prevent it from interacting with the following stage. f0 ≡ (f1 + f2)/2 and ∆f ≡ |f2 – f1| /2 the two third-order, close-in spurious tones will appear at f0 ± (3 • ∆f). The difference in power between two equal test tones and the intermodulation products is given by ∆dBc = 2 • (IM3 – P0) where IM3 is the intercept taken from the Typical Performance Curves and P0 is the power level in dBm at the 50Ω load for one of the two closely spaced test frequencies. For instance, at 10MHz the OPA643 at a gain of +5 has an intercept of 52dBm at the matched 50Ω load. If the full envelope of the two frequencies is 2Vp-p, then each tone will be at 4dBm. The third-order intermodulation spurs will then be 2 • (52 – 4) = 96dBc below the test tone power level (–92dBm). If this same 2Vp-p two-tone envelope were delivered directly into the input of an ADC without the matching loss or loading of the 50Ω/50Ω network, the intercept would increase to at least 58dBm. With the same signal and gain conditions, but now driving directly into a light load, the spurious tones will be at least 2 • (58 – 4) = 108dBc below the 4dBm test tone power levels centered at 10MHz. +5V 5kΩ +VS 100Ω 1kΩ 0.1µF Supply Decoupling Not Shown OPA643 5kΩ NOISE PERFORMANCE The OPA643 complements its ultra-low harmonic distortion with low input noise terms. The input voltage noise combines with the two input current noise terms to give low output noise under a wide variety of operating conditions. Figure 8 shows the op amp noise analysis model with all noise terms included. In this model, all voltage and current noise density terms are expressed in nV/√Hz or pA/√Hz respectively. VO –5V RG RF VI –VS ENI FIGURE 7. DC Adjustment for Second-Harmonic Reduction. For a 1Vp-p output swing in the 10 to 20MHz region, an output DC voltage in the ±1.5V range will null the secondharmonic distortion. Tests of this technique with a 200Ω converter input load have shown greater than 15dB improvement in the second-harmonic component. Once the required DC offset voltage is found for a particular board, circuit, and signal requirement, the voltage is very repeatable from part to part and may be fixed permanently at the noninverting input. Minimal degradation in second harmonic distortion over temperature has been observed. EO OPA643 RS IBN ERS RF √ 4kTRS 4kT RG RG IBI √ 4kTRF 4kT = 1.6E –20J at 290°K FIGURE 8. Op Amp Noise Analysis Model. ® 13 OPA643 The total output noise voltage density can be computed as the square root of the sum of all squared output noise voltage contributors. Equation 1 shows the general form for the output noise voltage using the terms shown in Figure 8. DC OFFSET CONTROL The OPA643 provides excellent DC signal accuracy due to the combination of high open-loop gain, high commonmode rejection, high power supply rejection, low input offset voltage and low bias current offset errors. The high grade (B) version of any package type provides less than 1.5mV input offset voltage. To take full advantage of this low input offset voltage, careful attention to input bias current cancellation is also required. The high speed input stage for the OPA643 has a relatively high input bias current (19µA typical into each input pin) but with a very close match between the two input currents—typically 100nA input offset current. The total output offset voltage may be considerably reduced by matching the source resistances which appear at the two inputs. For example, one way to include bias current cancellation in the circuit of Figure 1 would be to insert a 55Ω series resistor into the noninverting input after the 50Ω terminating resistor, RT. When the 50Ω source resistor is DC coupled, this will increase the source resistance for the non-inverting input bias current to 80Ω. Since this is now equal to the resistance appearing at inverting input (RF || RG), the circuit will cancel the gains for the bias currents to the output, leaving only the offset current times the feedback resistor as a residual DC error term at the output. Using a 402Ω feedback resistor, this output error will now be less than 3uA • 402Ω = 1.2mV over the full temperature range. Eq. 1 EO = (E 2 NI ) + ( I BN R S ) + 4kTR S NG 2 + ( I BI R F ) + 4kTR F NG 2 2 Dividing this expression by the noise gain (NG = (1+RF/ RG)) will give the equivalent input referred spot noise voltage at the noninverting input as shown in Equation 2. Eq. 2 2 I R 4kTR F 2 E N = E NI 2 + ( I BN R S ) + 4kTR S + BI F + NG NG Evaluating these two equations for the OPA643 component values shown in Figure 1 will give a total output spot noise voltage of 13.3nV/√Hz and a total equivalent input spot noise voltage of 2.7nV/√Hz. Narrowband communications systems are more commonly concerned with the Noise Figure (NF) for the amplifier. The total input referred voltage noise expression (Equation 2 above), may be used to calculate the noise figure. Equation 3 shows the noise figure expression using the EN of Equation 2 for the non-inverting configuration where the input termination resistor RT has been set to match the 50Ω source impedance (as shown in Figure 1). A fine scale output offset null, or DC operating point adjustment, is often required. Numerous techniques are available for introducing DC offset control into an op amp circuit. Most of these techniques eventually reduce to setting up a DC current through the feedback resistor. In selecting an offset trim method, one key consideration is the impact on the desired signal path frequency response. If the signal path is intended to be non-inverting, the offset control is best applied as an inverting summing signal to avoid interaction with the signal source. If the signal path is intended to be inverting, applying the offset control to the non-inverting input may be considered—however, the DC offset voltage on the summing junction will set up a DC current back into the source which must be considered. Applying an offset adjustment to the inverting op amp input can change the noise gain and frequency response flatness. For a DC coupled inverting amplifier, Figure 10 shows one example of an offset adjustment technique that has minimal impact on the signal frequency response. In this case, the DC offsetting current is brought into the inverting input node through a resistor which is much larger than the signal path resistors. This will insure that the adjustment circuit has minimal effect on the noise gain and hence the frequency response. E 2 NF = 10 log 2 + N Eq. 3 kTRs Evaluating Equation 3 for the circuit of Figure 1 gives a Noise Figure = 15.9dB. Input transformer coupling can be used to reduce this noise figure. A broadband pulse transformer can provide both a noiseless voltage gain and a more optimum source impedance to minimize the noise figure. Figure 9 shows an example built from the circuit of Figure 1, in which the transformer turns ratio has been set to the closest integer for minimum noise figure. This optimum turns ratio is calculated by: Eq. 4 ( ) N OPT = Nearest Integer E N / I BN • ( R S / 2 ) G = 15V/V [23.5dB] RS = 50Ω 1:6 Supply Decoupling Not Shown 50Ω 1.8kΩ OPA643 50Ω Load THERMAL ANALYSIS The OPA643 will not require heatsinking under most operating conditions. Maximum desired junction temperature will set the maximum allowable internal power dissipation as described below. In no case should the maximum junction temperature be allowed to exceed 175°C. 402Ω 5.7dB Noise Figure 100Ω FIGURE 9. Reduced Noise Figure Circuit. ® OPA643 14 b) Minimize the distance (< 0.25") from the power supply pins to high frequency 0.1µF decoupling capacitors. At the device pins, the ground and power plane layout should not be in close proximity to the signal I/O pins. Avoid narrow power and ground traces to minimize inductance between the pins and the decoupling capacitors. The primary power supply connections (on pins 4 and 7) should always be decoupled with these capacitors. Optional output stage power supply connections on pins 5 and 8 may be used to get a slight improvement in harmonic distortion and settling time (for the 8-pin packaged parts). Place additional 0.1µF decoupling capacitors very near to these pins to improve performance. Larger (2.2µF to 6.8µF) decoupling capacitors, effective at lower frequency, should also be used on the main supply pins. These may be placed somewhat farther from the device and may be shared among several devices in the same area of the PC board. +5V Supply Decoupling Not Shown 0.1µF OPA643 200Ω VO –5V +5V RG 250Ω RF 1kΩ VI 5kΩ 20kΩ ±200mV Output Adjustment 10kΩ 0.1µF 5kΩ VO VI =– RF RG = –4 c) Careful selection and placement of external components will preserve the high frequency performance of the OPA643. Resistors should be a very low reactance type. Surface mount resistors work best and allow tighter overall layout. Metal film and carbon composition axially leaded resistors can also provide good high frequency performance. Again, keep their leads and PC board trace length as short as possible. Never use wirewound type resistors in a high frequency application. Since the output pin and inverting input pin are the most sensitive to parasitic capacitance, always position the feedback and series output resistor, if any, as close as possible to the output pin. Other network components, such as non-inverting input termination resistors, should also be placed close to the package. Where double side component mounting is allowed, place the feedback resistor directly under the package on the other side of the board between the output and inverting input pins. Even with a low parasitic capacitance shunting the external resistors, excessively high resistor values can create significant time constants that can degrade performance. Good axial metal film or surface mount resistors have approximately 0.2pF in shunt with the resistor. For resistor values > 1.5kΩ, this parasitic capacitance can add a pole and/or zero below 500MHz that can effect circuit operation. Keep resistor values as low as possible consistent with load driving considerations. The 402Ω feedback used in the typical performance specifications is a good starting point for design. –5V FIGURE 10. DC Coupled, Inverting Gain of –4, with Output Offset Adjustment. Operating junction temperature (TJ) is given by TA + PD • θJA. The total internal power dissipation (PD) is the sum of quiescent power (PDQ) and additional power dissipated in the output stage (PDL) to deliver load power. Quiescent power is simply the specified no-load supply current times the total supply voltage across the part. PDL will depend on the required output signal and load but would, for a grounded resistive load, be at a maximum when the output is fixed at a voltage equal to 1/2 either supply voltage (for equal bipolar supplies). Under this condition PDL = VS2/(4 • RL) where RL includes feedback network loading. Note that it is the power in the output stage and not into the load that determines internal power dissipation. As a worst case example, compute the maximum TJ using an OPA643N (SOT23-5 package) in the circuit of Figure 1 operating at the maximum specified ambient temperature of +85°C. PD = 10V • 26mA + 52 /(4 • (100Ω || 502Ω)) = 335mW. Maximum TJ = +85°C + (0.335Ω • 150°C/W) = 135°C. BOARD LAYOUT GUIDELINES Achieving optimum performance with a high frequency amplifier like the OPA643 requires careful attention to board layout parasitics and external component types. Recommendations that will optimize performance include: d) Connections to other wideband devices on the board may be made with short direct traces or through on-board transmission lines. For short connections, consider the trace and the input to the next device as a lumped capacitive load. Relatively wide traces (50 to 100mils) should be used, preferably with ground and power planes opened up around them. Estimate the total capacitive load and set RS from the plot of recommended RS vs Capacitive Load. Low parasitic capacitive loads (< 5pF) may not need an RS since the OPA643 is nominally compensated to operate with a 2pF parasitic load. Higher parasitic a) Minimize parasitic capacitance to any AC ground for all of the signal I/O pins. Parasitic capacitance on the output and inverting input pins can cause instability; on the non-inverting input, it can react with the source impedance to cause unintentional bandlimiting. To reduce unwanted capacitance, a window around the signal I/O pins should be opened in all of the ground and power planes around those pins. Otherwise, ground and power planes should be unbroken elsewhere on the board. ® 15 OPA643 capacitive loads without an RS are allowed as the signal gain increases (increasing the unloaded phase margin). If a long trace is required, and the 6dB signal loss intrinsic to a doubly terminated transmission line is acceptable, implement a matched impedance transmission line using microstrip or stripline techniques (consult an ECL design handbook for microstrip and stripline layout techniques). A 50Ω environment is normally not necessary on board, and in fact a higher impedance environment will improve distortion as shown in the distortion vs load plots. With a characteristic board trace impedance defined based on board material and trace dimensions, a matching series resistor into the trace from the output of the OPA643 is used as well as a terminating shunt resistor at the input of the destination device. Remember also that the terminating impedance will be the parallel combination of the shunt resistor and the input impedance of the destination device: this total effective impedance should be set to match the trace impedance. Multiple destination devices are best handled as separate transmission lines, each with their own series and shunt terminations. If the 6dB attenuation of a doubly terminated transmission line is unacceptable, a long trace can be series-terminated at the source end only. Treat the trace as a capacitive load in this case and set the series resistor value as shown in the plot of RS vs Capacitive Load. This will not preserve signal integrity as well as a doubly terminated line. If the input impedance of the destination device is low, there will be some signal attenuation due to the voltage divider formed by the series output into the terminating impedance. High input overdrive signals can also cause significant differential voltage between the + and – inputs. Where this voltage can exceed the maximum rated voltage of ±1.2V, external Schottky protection diodes should be added across the two inputs. Again, the capacitance added by these diodes can degrade the noise and AC performance and should be used only where necessary. Figure 12 shows a fully featured input protection circuit for the OPA643. This is the circuit of Figure 1 with additional limiting resistors into the inputs and Schottky clamp diodes across the inputs. These resistor values have been selected to limit the degradation in noise and frequency response, achieve DC bias current cancellation, and limit the current that will flow under overdrive conditions. +V CC External Pin Internal Circuitry –V CC FIGURE 11. Internal ESD Protection. 50Ω Source e) Socketing a high speed part like the OPA643 is not recommended. The additional lead length and pin-to-pin capacitance introduced by the socket can create an extremely troublesome parasitic network which can make it almost impossible to achieve a smooth, stable frequency response. Best results are obtained by soldering the OPA643 onto the board. If socketing for the DIP package is desired, high frequency flush mount pins (e.g., McKenzie Technology #710C) can give good results. +5V 125Ω Power Supply Decoupling Not Shown D2 50Ω 50Ω OPA643 D1 –5V 505Ω 50Ω 126Ω INPUT AND ESD PROTECTION D1, D2 → IN5911 (or equivalent) The OPA643 is built using a very high speed complementary bipolar process. The internal junction breakdown voltages are relatively low for these very small geometry devices. These breakdowns are reflected in the Absolute Maximum Ratings table. All device pins are protected with internal ESD protection diodes to the power supplies as shown in Figure 11 FIGURE 12. OPA643 Gain of +5 with Input Protection. DESIGN-IN TOOLS DEMONSTRATION BOARDS These diodes provide moderate protection to input overdrive voltages above the supplies as well. The protection diodes can typically support 30mA continuous current. Where higher currents are possible (e.g. in systems with ±15V supply parts driving into the OPA643), current limiting series resistors should be added into the two inputs. Keep these resistor values as low as possible since high values degrade both noise performance and frequency response. Several PC boards are available in the initial evaluation of circuit performance using the OPA643 in its three package styles. Two partially assembled boards are available for sale to support the DIP (P suffix) and SO-8 (U-suffix) packages. These boards come partially assembled with power supply and I/O connectors but do not have the amplifier or resistor networks loaded. Both boards are configured for low ® OPA643 16 MACROMODELS AND APPLICATIONS SUPPORT Computer simulation of circuit performance using SPICE is often useful when analyzing the performance of analog circuits and systems. This is particularly true for video and RF amplifier circuits where parasitic capacitance and inductance can have a major effect on circuit performance. A SPICE model for the OPA643 is available through the Burr-Brown Internet web page (http://www.burr-brown.com) or as a disk from the Burr-Brown Applications department (1-800-548-6132). The Application department is also available for design assistance at this number. These models do a good job of predicting small signal AC and transient performance under a wide variety of operating conditions. They do not do as well in predicting the harmonic distortion or dG/dP characteristics. These models do not attempt to distinguish among the various package types in their small signal AC performance. distortion, non-inverting amplifier operation. Order these boards by the following part numbers from your local BurrBrown distributor: DEM-OPA64XP-N for the OPA643P and OPA643PB (8-pin DIP package) DEM-OPA64XU-N for the OPA643U and OPA643UB (8-pin SO package) The SOT23-5 package version of the OPA643 may be evaluated using a single unpopulated board used for numerous SOT23-5 packaged amplifiers available from Burr-Brown. This board is available from the Burr-Brown Literature department as an unpopulated board attached to a descriptive document. This board, the DEM-OPA6xxN, is available free by requesting literature number MKT-348. ® 17 OPA643