SIDACtor ® Protection Thyristors Broadband Optimized™ Protection MC Series - Modified TO-220 Description MC Series Modified TO-220 are low capacitance SIDACtor® devices designed to protect various types of broadband equipment from damaging overvoltage transients. The series provides a robust single port solution that enables equipment to comply with various global regulatory standards while limiting the impact to broadband signals. Features and Benefits t 40% lower capacitance than our Baseband Protectors, for applications that demand greater signal integrity t Low voltage overshoot Agency Approvals t Low on-state voltage Agency t Does not degrade with use Agency File Number t Fails short circuit when surged in excess of ratings E133083 Pinout Designation t Custom lead forms available t Robust Modified TO-220 Package Applicable Global Standards PIN 1 PIN 3 PIN 2 Schematic Symbol 1 (T) 3 t TIA-968-A t GR 1089 Intra-building* t TIA-968-B t IEC 61000-4-5 t ITU K.20/21 Enhanced Level t YD/T 1082 t ITU K.20/21 Basic Level t YD/T 950 t YD/T 993 t GR 1089 Inter-building* 2 (G) *A-rated parts require series resistance (R) Electrical Characteristics VDRM VS @lDRM=5μA @100V/μs Part Number Marking V min V max VDRM @100V/μs IH V min V max mA min Pins 1-2, 3-2 P0302AAMCLxx P0302AAMC P0602AAMCLxx P0602AAMC P0602ACMCLxx P0602ACMC P1402ACMCLxx P1402ACMC P1602ACMCLxx P1602ACMC P2202ACMCLxx P2202ACMC P2702ACMCLxx P2702ACMC P3002ACMCLxx P3002ACMC P3602ACMCLxx P3602ACMC P4202ACMCLxx P4202ACMC 6 25 25 58 65 90 120 140 170 190 25 40 40 77 95 130 160 180 220 250 VS @lDRM=5μA Pins 1-3 12 50 50 116 130 180 240 280 340 380 Pins 1-2, 3-2 50 80 80 154 190 260 320 360 440 500 50 50 50 150 150 150 150 150 150 150 IS IT VT @ IT=2.2 Amps mA max A max V min 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 4 4 4 4 4 4 4 4 4 4 Capacitance See Capacitance Values Table Table continues on next page. © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 80 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Electrical Characteristics (continued) Part Number VDRM VS V min V max @lDRM=5μA @100V/μs Marking VDRM VS @lDRM=5μA @100V/μs V min V max Pins 1-2, 3-2 Pins 1-3 VT @ IT=2.2 Amps Capacitance IH IS IT mA min Pins 1-2, 3-2 mA max A max V min P4802ACMCLxx P4802ACMC 220 300 440 600 150 800 2.2 4 P6002ACMCLxx P6002ACMC 275 350 550 700 150 800 2.2 4 See Capacitance Values Table Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). - XX Part Number Suffix: ‘RP’ (Reel Pack), Blank (Bulk Pack), or ‘60’ (Type 60 lead form, Bulk Pack. Special order item -- contact factory.) Capacitance Values Part Number P0302AAMCLxx P0602AAMCLxx P0602ACMCLxx P1402ACMCLxx P1602ACMCLxx P2202ACMCLxx P2702ACMCLxx P3002ACMCLxx P3602ACMCLxx P4202ACMCLxx P4802ACMCLxx P6002ACMCLxx pF Pin 1-2 / 3-2 Tip-Ground, Ring-Ground MIN MAX 25 55 15 35 25 45 40 60 35 55 45 70 40 60 35 55 35 50 30 50 30 45 30 45 pF Pin 1-3 Tip-Ring MIN MAX 15 35 10 20 10 25 20 35 20 35 25 40 20 35 20 35 15 30 15 30 15 30 15 25 Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings Series IPP 0.2x310 0.5x700 2 2x10 2x10 2 8x20 1.2x50 2 10x160 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 1 1 1 1 ITSM 50/60 Hz di/dt A min A min A min A min A min A min A min A min A min A min A/μs Max A 20 150 150 90 50 75 75 45 75 20 500 C 50 500 400 200 150 200 175 100 200 30 500 Notes: 1 Current waveform in μs 2 Voltage waveform in μs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP$ - The device must initially be in thermal equilibrium with -40°C < TJ <¡$ © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 81 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Thermal Considerations Package Symbol Parameter Value Unit TJ Operating Junction Temperature Range UP °C TS Storage Temperature Range UP °C R0JA Thermal Resistance: Junction to Ambient 50 °C/W Modified TO-220 PIN 1 PIN 3 PIN 2 V-I Characteristics tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP +I IT IS IH IDRM -V +V VT VDRM VS tr = rise time to peak value td = decay time to half value Peak Value 100 Waveform = tr x td 50 Half Value 0 0 td tr t – Time (μs) -I Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature IH 10 8 6 25 °C 4 Ratio of Percent of VS Change – % 12 IH (TC = 25ºC) 2.0 14 2 0 -4 -6 1.8 1.6 1.4 25°C 1.2 1.0 0.8 0.6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. -20 82 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) ¡$ ¡$ 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) ¡$ - Temperature (tL) 60-150 secs. Peak Temp (TP) ¡$ Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed ¡$ Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications Environmental Specifications Lead Material Copper Alloy High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ¡$PS¡$ 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Terminal Finish 100% Matte-Tin Plated Temp Cycling ¡$UP¡$NJOEXFMMVQUP cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC¡$ 3)VQUPIST&*" JEDEC, JESD22-A-101 High Temp Storage ¡$IST.*-45%.FUIPE JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock ¡$UP¡$NJOEXFMMTFDUSBOTGFS 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) ¡$3)BUNVQUPIST&*" JEDEC, JESD22-A-102 Resistance to Solder Heat ¡$TFDT.*-45%.FUIPE Moisture Sensitivity Level 3)¡$ISTSFnPXDZDMFT ¡$1FBL +&%&$+45%-FWFM Body Material UL recognized epoxy meeting flammability classification 94V-0 © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 83 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Part Marking Part Numbering P xxx 2 A x MC L xx TYPE P = SIDACtor XXXXXXXXX Blank, RP or 60 -- for Type 60 orders, contact factory MEDIAN VOLTAGE xxxxx RoHS COMPLIANT CONSTRUCTION VARIABLE IPP RATING Dimensions - Modified TO-220 Tape and Reel Specification — Modified TO-220 Inches O Min D Temperature Measurement Point F G P PIN 3 PIN 2 PIN 1 L K H M N J The modified TO-220 package is designed to meet mechanical standards as set forth in JEDEC publication number 95. Millimeters Max Min 0.240 (6.10) Max A 0.400 0.410 10.16 10.42 D 0.360 0.375 9.14 9.53 F 0.110 0.130 2.80 3.30 G 0.540 0.575 13.71 14.61 H 0.025 0.035 0.63 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.90 M 0.070 0.085 1.78 2.16 N O P 0.018 0.024 0.46 0.61 0.178 0.290 0.188 0.310 4.52 7.37 4.78 7.87 A 0.720 (18.29) 0.360 (9.14) 0.500 (12.7) 0.100 (2.54) 0.100 (2.54) Dimensions are in inches (and millimeters). Direction of Feed 1.968 (50.0) Quantity Added Suffix Industry Standard Modified TO-220 Tape and Reel Pack 700 RP EIA-468-B 500 N/A N/A 500 60 (special order item, contact factory for details) N/A © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 0.750 ± 0.010 (19.05 ± 0.25) 14.173 (360.0) Description Modified TO-220 Bulk Pack Modified TO-220, Type 60 Lead Form Bulk Pack 0.019 (0.5) 1.626 (41.15) Packing Options Package Type Date Code MC Series PACKAGE TYPE A Part Marking Code (Refer to Electrical Characteristics Table) PACKING OPTIONS 84 Revised: February 22, 2011