DATA SHEET Solid State Relay OCMOS FET PS710A-1A,PS710AL-1A 6-PIN DIP, 0.1 Ω LOW ON-STATE RESISTANCE 1.8 A CONTINUOUS LOAD CURRENT 1-ch Optical Coupled MOS FET DESCRIPTION The PS710A-1A and PS710AL-1A are solid state relays containing GaAs LEDs on the light emitting side (input side) and MOS FETs on the output side. It is suitable for PLC, etc. because of its large continuous load current and low on-state resistance. The PS710AL-1A has a surface mount type lead. FEATURES • Low on-state resistance (Ron = 0.1 Ω TYP.) • Large continuous load current (IL = 1.8 A) • 1 channel type (1 a output) • Low LED operating current (IF = 2 mA) • Designed for AC/DC switching line changer • Small package (6-pin DIP) • Low offset voltage • PS710AL-1A: Surface mount type APPLICATIONS • Measurement equipment • FA equipment The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all devices/types available in every country. Please check with local NEC representative for availability and additional information. Document No. P14574EJ4V0DS00 (4th edition) Date Published June 2000 NS CP(K) Printed in Japan The mark • shows major revised points. © 1999, 2000 PS710A-1A,PS710AL-1A PACKAGE DIMENSIONS (in millimeters) PS710A-1A 9.25±0.5 TOP VIEW 6 5 4 1 2 3 1. LED Anode 2. LED Cathode 3. NC 4. MOS FET Drain 5. MOS FET Source 6. MOS FET Drain 7.62 3.5±0.3 3.3±0.3 4.15±0.3 6.5±0.5 0.5±0.1 1.34±0.1 0.25 M 0 to 15˚ 2.54 PS710AL-1A 9.25±0.5 TOP VIEW 6 5 4 1 2 3 1. LED Anode 2. LED Cathode 3. NC 4. MOS FET Drain 5. MOS FET Source 6. MOS FET Drain 3.5±0.3 0.10+0.10 –0.05 6.5±0.5 1.34±0.1 0.25 M 2 0.9±0.25 2.54 9.60±0.4 Data Sheet P14574EJ4V0DS00 PS710A-1A,PS710AL-1A ORDERING INFORMATION Part Number PS710A-1A Package 6-pin DIP Packing Style Magazine case 50 pcs PS710AL-1A PS710AL-1A-E3 Application Part Number *1 PS710A-1A PS710AL-1A Embossed Tape 1 000 pcs/reel PS710AL-1A-E4 *1 For the application of the Safety Standard, following part number should be used. Data Sheet P14574EJ4V0DS00 3 PS710A-1A,PS710AL-1A ABSOLUTE MAXIMUM RATINGS (TA = 25 °C, unless otherwise specified) Diode Parameter Symbol Ratings Unit Forward Current (DC) IF 50 mA Reverse Voltage VR 5.0 V PD 50 mW IFP 1 A VL 60 V IL 1.8 A Power Dissipation Peak Forward Current MOS FET *1 Break Down Voltage Continuous Load Current Connection A *2 Pulse Load Current Connection B 2.0 Connection C 3.6 *3 ILP 3.6 A PD 560 mW BV 1 500 Vr.m.s. Total Power Dissipation PT 610 mW Operating Ambient Temperature TA −40 to +85 °C Storage Temperature Tstg −40 to +100 °C (AC/DC Connection) Power Dissipation Isolation Voltage *4 *1 PW = 100 µs, Duty Cycle = 1 % *2 Conditions: IF ≥ 2 mA. The following types of load connections are available. Connection A Connection B Connection C 1 2 3 1 2 3 1 2 3 1 2 3 6 5 4 6 5 IL IL VL (AC/DC) L L + VL (DC) – 4 6 5 4 6 5 IL 4 IL IL L L IL + IL – + VL (DC) + VL (DC) – *3 PW = 100 ms, 1 shot *4 AC voltage for 1 minute at TA = 25 °C, RH = 60 % between input and output 4 Data Sheet P14574EJ4V0DS00 PS710A-1A,PS710AL-1A RECOMMENDED OPERATING CONDITIONS (TA = 25 °C) Parameter Symbol MIN. TYP. MAX. Unit LED Operating Current IF 2 10 20 mA LED Off Voltage VF 0 0.5 V ELECTRICAL CHARACTERISTICS (TA = 25 °C) Parameter Diode MOS FET Coupled Symbol Conditions MIN. TYP. MAX. Unit 1.2 1.4 V Forward Voltage VF IF = 10 mA Reverse Current IR VR = 5 V 5.0 µA Off-state Leakage Current ILoff VD = 60 V 1.0 µA Output Capacitance Cout VD = 0 V, f = 1 MHz LED On-state Current IFon IL = 1.8 A On-state Resistance 320 pF 2.0 mA Ron IF = 10 mA, IL = 1.8 A, t ≤ 10 ms 0.1 0.2 Ω Turn-on Time *1 ton IF = 10 mA, VO = 5 V, RL = 500 Ω, 1.0 3.0 ms Turn-off Time *1 toff PW ≥ 10 ms 0.05 1.0 Isolation Resistance RI-O VI-O = 1.0 kVDC Isolation Capacitance CI-O V = 0 V, f = 1 MHz Ω 9 10 0.5 pF *1 Test Circuit for Switching Time IF Pulse Input VL 50 % Input 0 VO = 5 V Input monitor 90 % VO monitor Output Rin RL 10 % ton Data Sheet P14574EJ4V0DS00 toff 5 PS710A-1A,PS710AL-1A TYPICAL CHARACTERISTICS (TA = 25 °C, unless otherwise specified) MAXIMUM LOAD CURRENT vs. AMBIENT TEMPERATURE MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE 3.0 Maximum Load Current IL (A) Maximum Forward Current IF (mA) 100 80 60 40 20 0 –25 0 25 50 75 85 2.5 2.0 1.5 1.0 0.5 0.0 –25 100 0 25 50 75 85 Ambient Temperature TA (˚C) Ambient Temperature TA (˚C) FORWARD VOLTAGE vs. AMBIENT TEMPERATURE OUTPUT CAPACITANCE vs. APPLIED VOLTAGE 100 500 1.6 1.4 1.2 1.0 0.8 –25 0 25 50 75 Output Capacitance Cout (pF) Forward Voltage VF (V) f = 1 MHz IF = 50 mA 30 mA 20 mA 10 mA 5 mA 1 mA 400 300 200 100 0 100 20 40 120 OFF-STATE LEAKAGE CURRENT vs. AMBIENT TEMPERATURE LOAD CURRENT vs. LOAD VOLTAGE 3.0 IF = 10 mA VD = 60 V 2.0 10–7 10–8 10–9 10 100 Applied Voltage VD (V) Load Current IL (A) Off-state Leakage Current ILoff (A) 80 Ambient Temperature TA (˚C) 10–6 1.0 –0.45 –0.30 0 –0.15 0.15 –1.0 –10 10–11 0 –2.0 20 40 60 80 –3.0 Load Voltage VL (V) Ambient Temperature TA (˚C) 6 60 Data Sheet P14574EJ4V0DS00 0.30 0.45 PS710A-1A,PS710AL-1A NORMALIZED ON-STATE RESISTANCE vs. AMBIENT TEMPERATURE ON-STATE RESISTANCE DISTRIBUTION 30 Normalized to 1.0 at TA = 25 ˚C, IF = 10 mA, IL = 1.8 A 2.5 2.0 1.5 1.0 0 25 50 10 0.11 0.10 Ambient Temperature TA (˚C) On-state Resistance Ron (Ω) TURN-ON TIME vs. FORWARD CURRENT TURN-OFF TIME vs. FORWARD CURRENT 8.0 0.5 6.0 4.0 2.0 0 0.4 0.3 0.2 0.1 10 30 20 40 0 10 30 20 Forward Current IF (mA) Forward Current IF (mA) TURN-ON TIME DISTRIBUTION TURN-OFF TIME DISTRIBUTION 30 30 n = 50 pcs, IF = 10 mA, VO = 5 V, RL = 500 Ω 25 15 10 40 n = 50 pcs, IF = 10 mA, VO = 5 V, RL = 500 Ω 25 Number (pcs) 20 20 15 10 5 5 0 VO = 5 V, RL = 500 Ω Turn-off Time toff (ms) Turn-on Time ton (ms) 15 0 100 75 VO = 5 V, RL = 500 Ω Number (pcs) 20 5 0.5 0.0 –25 n = 50 pcs, IF = 10 mA, IL = 1.8 A, t 10 ms 25 Number (pcs) Normalized On-state Resistance Ron 3.0 1.0 2.0 0 0.04 0.08 Turn-off Time toff (ms) Turn-on Time ton (ms) Data Sheet P14574EJ4V0DS00 7 PS710A-1A,PS710AL-1A NORMALIZED TURN-OFF TIME vs. AMBIENT TEMPERATURE NORMALIZED TURN-ON TIME vs. AMBIENT TEMPERATURE Normalized to 1.0 at TA = 25 ˚C, IF = 10 mA, VO = 5 V, RL = 500 Ω 2.5 2.0 1.5 1.0 0.5 0.0 –25 0 25 50 75 100 3.0 Normalized Turn-off Time toff Normalized Turn-on Time ton 3.0 2.5 2.0 1.5 1.0 0.5 0.0 –25 0 25 50 75 Ambient Temperature TA (˚C) Ambient Temperature TA (˚C) Remark The graphs indicate nominal characteristics. 8 Normalized to 1.0 at TA = 25 ˚C, IF = 10 mA, VO = 5 V, RL = 500 Ω Data Sheet P14574EJ4V0DS00 100 PS710A-1A,PS710AL-1A TAPING SPECIFICATIONS (in millimeters) 4.3±0.2 10.3±0.1 7.5±0.1 1.55±0.1 16.0±0.3 2.0±0.1 4.0±0.1 1.75±0.1 Outline and Dimensions (Tape) 0.3 10.4±0.1 1.55±0.1 12.0±0.1 Tape Direction PS710AL-1A-E3 PS710AL-1A-E4 Outline and Dimensions (Reel) 1.5 R 1.0 φ 21.0±0.8 φ 80.0±5.0 φ 330 2.0±0.5 φ 13.0±0.5 16.4 +2.0 –0.0 Packing: 1 000 pcs/reel Data Sheet P14574EJ4V0DS00 9 PS710A-1A,PS710AL-1A RECOMMENDED SOLDERING CONDITIONS (1) Infrared reflow soldering • Peak reflow temperature 235 °C or below (package surface temperature) • Time of temperature higher than 210 °C 30 seconds or less • Number of reflows Two • Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended.) Package Surface Temperature T (˚C) Recommended Temperature Profile of Infrared Reflow (heating) to 10 s 235 ˚C (peak temperature) 210 ˚C to 30 s 100 to 160 ˚C 60 to 120 s (preheating) Time (s) (2) Dip soldering • Temperature 260 °C or below (molten solder temperature) • Time 10 seconds or less • Number of times One • Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended.) (3) Cautions • Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. 10 Data Sheet P14574EJ4V0DS00 PS710A-1A,PS710AL-1A [MEMO] Data Sheet P14574EJ4V0DS00 11 PS710A-1A,PS710AL-1A CAUTION Within this device there exists GaAs (Gallium Arsenide) material which is a harmful substance if ingested. Please do not under any circumstances break the hermetic seal. • The information in this document is current as of June, 2000. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC's data sheets or data books, etc., for the most up-to-date specifications of NEC semiconductor products. Not all products and/or types are available in every country. Please check with an NEC sales representative for availability and additional information. • No part of this document may be copied or reproduced in any form or by any means without prior written consent of NEC. NEC assumes no responsibility for any errors that may appear in this document. • NEC does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC semiconductor products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC or others. • Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of customer's equipment shall be done under the full responsibility of customer. NEC assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. • While NEC endeavours to enhance the quality, reliability and safety of NEC semiconductor products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC semiconductor products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment, and anti-failure features. • NEC semiconductor products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to semiconductor products developed based on a customer-designated "quality assurance program" for a specific application. The recommended applications of a semiconductor product depend on its quality grade, as indicated below. Customers must check the quality grade of each semiconductor product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC semiconductor products is "Standard" unless otherwise expressly specified in NEC's data sheets or data books, etc. If customers wish to use NEC semiconductor products in applications not intended by NEC, they must contact an NEC sales representative in advance to determine NEC's willingness to support a given application. (Note) (1) "NEC" as used in this statement means NEC Corporation and also includes its majority-owned subsidiaries. (2) "NEC semiconductor products" means any semiconductor product developed or manufactured by or for NEC (as defined above). M8E 00. 4