PSD4135G2 Flash In-System-Programmable Peripherals for 16-Bit MCUs PRELIMINARY DATA FEATURES SUMMARY ■ 5 V±10% Single Supply Voltage: ■ Up to 4 Mbit of Primary Flash Memory (8 uniform sectors) ■ 256Kbit Secondary Flash Memory (4 uniform sectors) ■ Up to 64 Kbit SRAM ■ Over 3,000 Gates of PLD: DPLD and CPLD ■ 52 Reconfigurable I/O ports ■ Enhanced JTAG Serial Port ■ Programmable power management ■ High Endurance: Figure 1. Packages – 100,000 Erase/Write Cycles of Flash Memory – 1,000 Erase/Write Cycles of PLD TQFP80 (U) January 2002 This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. 1/3 PSD4000 Series PSD4135G2 Flash In-System-Programmable Peripherals for 16-Bit MCUs Table of Contents Introduction ........................................................................................................................................................................................1 In-System Programming (ISP) JTAG .......................................................................................................................................2 In-Application re-Programming (IAP) .......................................................................................................................................2 Key Features......................................................................................................................................................................................3 PSD4000 Family ................................................................................................................................................................................3 Block Diagram....................................................................................................................................................................................4 Architectural Overview .......................................................................................................................................................................5 Memory ....................................................................................................................................................................................5 PLDs.........................................................................................................................................................................................5 I/O Ports ...................................................................................................................................................................................5 Microcontroller Bus Interface....................................................................................................................................................5 ISP via JTAG Port ....................................................................................................................................................................6 In-System Programming (ISP) .................................................................................................................................................6 In-Application re-Programming (IAP) .......................................................................................................................................6 Page Register...........................................................................................................................................................................6 Power Management Unit ..........................................................................................................................................................6 Development System .........................................................................................................................................................................7 Pin Descriptions .................................................................................................................................................................................8 Register Description and Address Offset .........................................................................................................................................11 Register Bit Definition ......................................................................................................................................................................12 Functional Blocks .............................................................................................................................................................................15 Memory Blocks .......................................................................................................................................................................15 Main Flash and Secondary Flash Memory Description ...................................................................................................15 SRAM...............................................................................................................................................................................26 Memory Select Signals ....................................................................................................................................................26 Page Register ..................................................................................................................................................................29 Memory ID Registers .......................................................................................................................................................30 PLDs.......................................................................................................................................................................................31 Decode PLD (DPLD)........................................................................................................................................................33 General Purpose PLD (GPLD).........................................................................................................................................33 Microcontroller Bus Interface..................................................................................................................................................36 Interface to a Multiplexed Bus..........................................................................................................................................36 Interface to a Non-multiplexed Bus ..................................................................................................................................36 Data Byte Enable Reference ...........................................................................................................................................38 Microcontroller Interface Examples..................................................................................................................................39 I/O Ports .................................................................................................................................................................................44 General Port Architecture ................................................................................................................................................44 Port Operating Modes ......................................................................................................................................................44 Port Configuration Registers (PCRs) ...............................................................................................................................48 Port Data Registers..........................................................................................................................................................49 Ports A, B and C – Functionality and Structure ...............................................................................................................50 Port D – Functionality and Structure ................................................................................................................................51 Port E – Functionality and Structure ................................................................................................................................51 Port F – Functionality and Structure ................................................................................................................................52 Port G – Functionality and Structure ................................................................................................................................52 i PSD4000 Series PSD4135G2 Flash In-System-Programmable Peripherals for 16-Bit MCUs Table of Contents Power Management ...............................................................................................................................................................53 Automatic Power Down (APD) Unit and Power Down Mode ...........................................................................................53 Other Power Savings Options..........................................................................................................................................57 Reset and Power On Requirement ..................................................................................................................................58 Programming In-Circuit using the JTAG-ISP Interface...........................................................................................................59 Standard JTAG Signals ...................................................................................................................................................60 JTAG Extensions .............................................................................................................................................................60 Security and Flash Memories Protection .........................................................................................................................60 Absolute Maximum Ratings .............................................................................................................................................................61 Operating Range..............................................................................................................................................................................61 Recommended Operating Conditions..............................................................................................................................................61 AC/DC Parameters ..........................................................................................................................................................................62 Example of Typical Power Calculation at Vcc = 5..0 V...........................................................................................................63 Example of Typical Power Calculation at Vcc = 5..0 V in Turbo Off Mode.............................................................................64 DC Characteristics (5 V ± 10% versions).........................................................................................................................................65 Microcontroller Interface – AC/DC Parameters (5 V ± 10% versions) .............................................................................................67 DC Characteristics (3.0 V to 3.6 V versions) ...................................................................................................................................71 Microcontroller Interface – AC/DC Parameters (3.0 V to 3.6 V versions) .......................................................................................73 Timing Diagrams ..............................................................................................................................................................................77 Pin Capacitance...............................................................................................................................................................................81 AC Testing Input/Output Waveforms ...............................................................................................................................................81 AC Testing Load Circuit ...................................................................................................................................................................81 Programming ...................................................................................................................................................................................81 Pin Assignments ..............................................................................................................................................................................82 Package Information ........................................................................................................................................................................83 Selector Guide .................................................................................................................................................................................85 Part Number Construction ...............................................................................................................................................................86 Ordering Information ........................................................................................................................................................................86 Document Revisions ........................................................................................................................................................................87 Worldwide Sales, Service and Technical Support ...........................................................................................................................88 ii PSD4000 Series PSD4135G2 Configurable Memory System on a Chip for 16-Bit Microcontrollers Preliminary Information 1.0 Introduction The PSD4000 series of Programmable Microcontroller (MCU) Peripherals brings In-System-Programmability (ISP) to Flash memory and programmable logic. The result is a simple and flexible solution for embedded designs. PSD4000 devices combine many of the peripheral functions found in MCU based applications: • 4 Mbit of Flash memory • A secondary Flash memory for boot or data • Over 3,000 gates of Flash programmable logic • 64 Kbit SRAM • Reconfigurable I/O ports • Programmable power management. 1 PSD4000 Series 1.0 Introduction (Cont.) Preliminary Information The PSD4135G2 device offers two methods to program PSD Flash memory while the PSD is soldered to a circuit board. ❏ In-System Programming (ISP) via JTAG An IEEE 1149.1 compliant JTAG-ISP interface is included on the PSD enabling the entire device (both flash memories, the PLD, and all configuration) to be rapidly programmed while soldered to the circuit board. This requires no MCU participation, which means the PSD can be programmed anytime, even while completely blank. The innovative JTAG interface to flash memories is an industry first, solving key problems faced by designers and manufacturing houses, such as: • First time programming – How do I get firmware into the flash the very first time? JTAG is the answer, program the PSD while blank with no MCU involvement. • Inventory build-up of pre-programmed devices – How do I maintain an accurate count of pre-programmed flash memory and PLD devices based on customer demand? How many and what version? JTAG is the answer, build your hardware with blank PSDs soldered directly to the board and then custom program just before they are shipped to customer. No more labels on chips and no more wasted inventory. • Expensive sockets – How do I eliminate the need for expensive and unreliable sockets? JTAG is the answer. Solder the PSD directly to the circuit board. Program first time and subsequent times with JTAG. No need to handle devices and bend the fragile leads. ❏ In-Application re-Programming (IAP) Two independent flash memory arrays are included so the MCU can execute code from one memory while erasing and programming the other. Robust product firmware updates in the field are possible over any communication channel (CAN, Ethernet, UART, J1850, etc) using this unique architecture. Designers are relieved of these problems: • Simultaneous read and write to flash memory – How can the MCU program the same memory from which it is executing code? It cannot. The PSD allows the MCU to operate the two flash memories concurrently, reading code from one while erasing and programming the other during IAP. • Complex memory mapping – How can I map these two memories efficiently? A Programmable Decode PLD is embedded in the PSD. The concurrent PSD memories can be mapped anywhere in MCU address space, segment by segment with extremely high address resolution. As an option, the secondary flash memory can be swapped out of the system memory map when IAP is complete. A built-in page register breaks the MCU address limit. • Separate program and data space – How can I write to flash memory while it resides in “program” space during field firmware updates, my 80C51XA won’t allow it The flash PSD provides means to “reclassify” flash memory as “data” space during IAP, then back to “program” space when complete. PSDsoft – ST’s software development tool – guides you through the design process stepby-step making it possible to complete an embedded MCU design capable of ISP/IAP in just hours. Select your MCU and PSDsoft will take you through the remainder of the design with point and click entry, covering...PSD selection, pin definitions, programmable logic inputs and outputs, MCU memory map definition, ANSI C code generation for your MCU, and merging your MCU firmware with the PSD design. When complete, two different device programmers are supported directly from PSDsoft – FlashLINK (JTAG) and PSDpro. The PSD4135G2 is available in an 80-pin TQFP package. Please refer to the revision block at the end of this document for updated information. 2 Preliminary Information 2.0 Key Features PSD4000 Series ❏ A simple interface to 16-bit microcontrollers that use either multiplexed or non-multiplexed busses. The bus interface logic uses the control signals generated by the microcontroller automatically when the address is decoded and a read or write is performed. A partial list of the MCU families supported include: • Intel 80196, 80296, 80186, and 80386EX • Motorola 68HC16, 68HC12, 683XX, and MC2001 • Philips 80C51XA • Infineon C16X devices • Hitachi H8 ❏ 4 Mbit Flash memory. This is the main Flash memory. It is divided into eight equal-sized blocks that can be accessed with user-specified addresses. ❏ Internal secondary 256 Kbit Flash boot memory. It is divided into four equal-sized blocks that can be accessed with user-specified addresses. This secondary memory brings the ability to execute code and update the main Flash concurrently. ❏ 64 Kbit SRAM. The SRAM’s contents can be protected from a power failure by connecting an external battery. ❏ General Purpose PLD (GPLD) with 24 outputs. The GPLD may be used to implement external chip selects or combinatorial logic function. ❏ Decode PLD (DPLD) that decodes address for selection of internal memory blocks. ❏ 52 individually configurable I/O port pins that can be used for the following functions: • MCU I/Os • PLD I/Os • Latched MCU address output • Special function I/Os. • I/O ports may be configured as open-drain outputs. ❏ Standby current as low as 50 µA for 5 V devices. ❏ Built-in JTAG compliant serial port allows full-chip In-System Programmability (ISP). With it, you can program a blank device or reprogram a device in the factory or the field. ❏ Internal page register that can be used to expand the microcontroller address space by a factor of 256. ❏ Internal programmable Power Management Unit (PMU) that supports a low power mode called Power Down Mode. The PMU can automatically detect a lack of microcontroller activity and put the PSD4000 into Power Down Mode. ❏ Erase/Write cycles: • Flash memory – 100,000 minimum • PLD – 1,000 minimum • 15 year data retention 3.0 PSD4000 Series Table 1. PSD4000 Product Matrix Part # PSD4000 Series PSD4000 Flash Serial ISP PLD Input Output PLD JTAG/ISP Inputs Macrocells Macrocells Outputs Port Device I/O Pins PSD4135G2 52 66 PSD4235G2* 52 82 24 16 Flash Main Memory Kbit 8 Sectors Boot Memory Kbit (4 Sectors) SRAM Kbit Supply Voltage 24 Yes 4096 256 64 5V 24 Yes 4096 256 64 5V *See PSD4235G2 Data Sheet. 3 CNTL0, CNTL1, CNTL2 4 MBIT MAIN FLASH MEMORY PAGE REGISTER EMBEDDED ALGORITHM 8 SECTORS 256 KBIT SECONDARY FLASH MEMORY (BOOT OR DATA) 4 SECTORS SECTOR SELECTS PROG. MCU BUS INTRF. FLASH DECODE PLD (DPLD) 66 64 KBIT BATTERY BACKUP SRAM PROG. PORT CSIOP RUNTIME CONTROL AND I/O REGISTERS FLASH ISP PLD (GPLD) GPLD OUTPUT PROG. PORT GPLD OUTPUT PORT F GPLD OUTPUT PROG. PORT PROG. PORT PROG. PORT PORT C PROG. PORT *Additional address lines can be brought into PSD via Port A, B, C, D, or F. PD0 – PD3 JTAG SERIAL CHANNEL PORT E PE0 – PE7 Preliminary Information PORT G PLD, CONFIGURATION & FLASH MEMORY LOADER PC0 – PC7 PORT D I/O PORT PLD INPUT GLOBAL CONFIG. & SECURITY PB0 – PB7 PORT B PROG. PORT PG0 – PG7 PA0 – PA7 PORT A ADIO PORT 66 PF0 – PF7 VSTDBY (PE6) SECTOR SELECTS SRAM SELECT AD0 – AD15 * POWER MANGMT UNIT PSD4000 Series PLD INPUT BUS Figure 1. PSD4000 Block Diagram 4 ADDRESS/DATA/CONTROL BUS Preliminary Information 4.0 PSD4000 Architectural Overview PSD4000 Series PSD4000 devices contain several major functional blocks. Figure 1 on page 3 shows the architecture of the PSD4000 device family. The functions of each block are described briefly in the following sections. Many of the blocks perform multiple functions and are user configurable. 4.1 Memory The PSD4000 contains the following memories: • 4 Mbit Flash • A secondary 256 Kbit Flash memory for boot or data • 64 Kbit SRAM. Each of the memories is briefly discussed in the following paragraphs. A more detailed discussion can be found in section 9. The 4 Mbit Flash is the main memory of the PSD4000. It is divided into eight equally-sized sectors that are individually selectable. The 256 Kbit secondary Flash memory is divided into four equally-sized sectors. Each sector is individually selectable. The 64 Kbit SRAM is intended for use as a scratchpad memory or as an extension to the microcontroller SRAM. If an external battery is connected to the PSD4000’s Vstby pin, data will be retained in the event of a power failure. Each block of memory can be located in a different address space as defined by the user. The access times for all memory types includes the address latching and DPLD decoding time. 4.2 PLDs The device contains two PLD blocks, each optimized for a different function, as shown in Table 2. The functional partitioning of the PLDs reduces power consumption, optimizes cost/performance, and eases design entry. The Decode PLD (DPLD) is used to decode addresses and generate chip selects for the PSD4000 internal memory and registers. The General Purpose PLD (GPLD) can implement user-defined external chip selects and logic functions. The PLDs receive their inputs from the PLD Input Bus and are differentiated by their output destinations, number of Product Terms. The PLDs consume minimal power by using Zero-Power design techniques. The speed and power consumption of the PLD is controlled by the Turbo Bit in the PMMR0 register and other bits in the PMMR2 registers. These registers are set by the microcontroller at runtime. There is a slight penalty to PLD propagation time when invoking the non-Turbo bit. 4.3 I/O Ports The PSD4000 has 52 I/O pins divided among seven ports (Port A, B, C, D, E, F and G). Each I/O pin can be individually configured for different functions. Ports can be configured as standard MCU I/O ports, PLD I/O, or latched address outputs for microcontrollers using multiplexed address/data busses. The JTAG pins can be enabled on Port E for In-System Programming (ISP). Ports F and G can also be configured as a data port for a non-multiplexed bus. 4.4 Microcontroller Bus Interface The PSD4000 easily interfaces with most 16-bit microcontrollers that have either multiplexed or non-multiplexed address/data busses. The device is configured to respond to the microcontroller’s control signals, which are also used as inputs to the PLDs. Section 9.3.5 contains microcontroller interface examples. Table 2. PLD I/O Table Name Decode PLD General PLD Abbreviation DPLD GPLD Inputs 66 66 Outputs 14 24 Product Terms 40 136 5 PSD4000 Series PSD4000 Architectural Overview (cont.) Preliminary Information 4.5 ISP via JTAG Port In-System Programming can be performed through the JTAG pins on Port E. This serial interface allows complete programming of the entire PSD4000 device. A blank device can be completely programmed. The JTAG signals (TMS, TCK, TSTAT, TERR, TDI, TDO) can be multiplexed with other functions on Port E. Table 3 indicates the JTAG signals pin assignments. 4.6 In-System Programming (ISP) Using the JTAG signals on Port E, the entire PSD4000 (memory, logic, configuration) device can be programmed or erased without the use of the microcontroller. Table 3. JTAG Signals on Port E Port E Pins JTAG Signal PE0 PE1 PE2 PE3 PE4 PE5 TMS TCK TDI TDO TSTAT TERR 4.7 In-Application re-Programming (IAP) The main Flash memory can also be programmed in-system by the microcontroller executing the programming algorithms out of the secondary Flash memory, or SRAM. Since this is a sizable separate block, the application can also continue to operate. The secondary Flash boot memory can be programmed the same way by executing out of the main Flash memory. Table 4 indicates which programming methods can program different functional blocks of the PSD4000. Table 4. Methods of Programming Different Functional Blocks of the PSD4000 Functional Block Main Flash memory Flash Boot memory PLD Array (DPLD and GPLD) PSD Configuration JTAG-ISP Device Programmer IAP Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No 4.8 Page Register The eight-bit Page Register expands the address range of the microcontroller by up to 256 times.The paged address can be used as part of the address space to access external memory and peripherals or internal memory and I/O. The Page Register can also be used to change the address mapping of blocks of Flash memory into different memory spaces for IAP. 4.9 Power Management Unit The Power Management Unit (PMU) in the PSD4000 gives the user control of the power consumption on selected functional blocks based on system requirements. The PMU includes an Automatic Power Down unit (APD) that will turn off device functions due to microcontroller inactivity. The APD unit has a Power Down Mode that helps reduce power consumption. The PSD4000 also has some bits that are configured at run-time by the MCU to reduce power consumption of the GPLD. The turbo bit in the PMMR0 register can be turned off and the GPLD will latch its outputs and go to standby until the next transition on its inputs. Additionally, bits in the PMMR2 register can be set by the MCU to block signals from entering the GPLD to reduce power consumption. See section 9.5. 6 Preliminary Information 5.0 Development System PSD4000 Series The PSD4000 series is supported by PSDsoft a Windows-based (95, 98, NT) software development tool. A PSD design is quickly and easily produced in a point and click environment. The designer does not need to enter Hardware Definition Language (HDL) equations (unless desired) to define PSD pin functions and memory map information. The general design flow is shown in Figure 2 below. PSDsoft is available from our web site (www.psdst.com) or other distribution channels. PSDsoft directly supports two low cost device programmers from ST, PSDpro and FlashLINK (JTAG). Both of these programmers may be purchased through your local rep/distributor, or directly from our web site using a credit card. The PSD4000 is also supported by third party device programmers, see web site for current list. Figure 2. PSDsoft Development Tool Choose MCU and PSD Automatically Configures MCU bus interface and other PSD attributes. Define PSD Pin and Node functions C Code Generation Point and click definition of PSD pin functions, internal nodes, and MCU system memory map. Generate C Code Specific to PSD Functions Merge MCU Firmware with PSD Configuration A composite object file is created containing MCU firmware and PSD configuration. MCU Firmware Hex or S-Record format User's choice of Microcontroller Compiler/Linker *.OBJ FILE PSD Programmer PSDPro or FlashLink (JTAG) *.OBJ file available for 3rd party programmers (Conventional or JTAG-ISP) 7 PSD4000 Series 6.0 Table 5. PSD4000 Pin Descriptions Preliminary Information The following table describes the pin names and pin functions of the PSD4000. Pins that have multiple names and/or functions are defined using PSDsoft. Pin Name Type Description ADIO0-7 3-7 10-12 I/O This is the lower Address/Data port. Connect your MCU address or address/data bus according to the following rules: 1. If your MCU has a multiplexed address/data bus where the data is multiplexed with the lower address bits, connect AD[0:7] to this port. 2. If your MCU does not have a multiplexed address/data bus, connect A[0:7] to this port. 3. If you are using an 80C51XA in burst mode, connect A4/D0 through A11/D7 to this port. ALE or AS latches the address. The PSD drives data out only if the read signal is active and one of the PSD functional blocks was selected. The addresses on this port are passed to the PLDs. ADIO8-15 13-20 I/O This is the upper Address/Data port. Connect your MCU address or address/data bus according to the following rules: 1. If your MCU has a multiplexed address/data bus where the data is multiplexed with the upper address bits, connect AD[8:15] to this port. 2. If your MCU does not have a multiplexed address/data bus, connect A[8:15] to this port. 3. If you are using an 80C51XA in burst mode, connect A12/D8 through A19/D15 to this port. ALE or AS latches the address. The PSD drives data out only if the read signal is active and one of the PSD functional blocks was selected. The addresses on this port are passed to the PLDs. CNTL0 59 I The following control signals can be connected to this port, based on your MCU: 1. WR — active-low write input. 2. R_W — active-high read/active low write input. 3. WRL — Write to low byte, active low This pin is connected to the PLDs. Therefore, these signals can be used in decode and other logic equations. CNTL1 60 I The following control signals can be connected to this port, based on your MCU: 1. RD — active-low read input. 2. E — E clock input. 3. DS — active-low data strobe input. 4. LDS — Strobe for low data byte, active low. This pin is connected to the PLDs. Therefore, these signals can be used in decode and other logic equations. CNTL2 8 Pin* (TQFP Pkg.) 40 I Read or other Control input pin with multiple configurations. Depending on the MCU interface selected, this pin can be: 1. PSEN — Program Select enable, active low in code fetch bus cycle (80C51XA mode) 2. BHE — High byte enable. 3. UDS — Strobe for high data byte, 16-bit data bus mode, active low. 4. SIZ0 — Byte enable input. 5. LSTRB — Low strobe input. This pin is also connected to PLD as input. Preliminary Information Table 5. PSD4000 Pin Descriptions PSD4000 Series Pin* (TQFP Pin Name Pkg.) Reset 39 Type Description I Active low input. Resets I/O Ports, PLD Micro⇔Cells, some of the configuration registers and JTAG registers. Must be active at power up. Reset also aborts the Flash programming/erase cycle that is in progress. (cont.) PA0-PA7 51-58 I/O CMOS or Open Drain Port A, PA0-7. This port is pin configurable and has multiple functions: 1. MCU I/O — standard output or input port 2. GPLD output. 3. Input to the PLD (can also be PLD input for address A16 and above). PB0-PB7 61-68 I/O CMOS or Open Drain Port B, PB0-7. This port is pin configurable and has multiple functions: 1. MCU I/O — standard output or input port. 2. GPLD output. 3. Input to the PLD (can also be PLD input for address A16 and above). PC0-PC7 41-48 I/O CMOS or Slew Rate Port C, PC0-7. This port is pin configurable and has multiple functions: 1. MCU I/O — standard output or input port. 2. External chip select (ECS0-7) output. 3. Input to the PLD (can also be PLD input for address A16 and above). PD0 79 I/O CMOS or Open Drain Port D pin PD0 can be configured as: 1. ALE or AS input — latches addresses on ADIO0-15 pins 2. AS input — latches addresses on ADIO0-15 pins on the rising edge. 3. Input to the PLD (can also be PLD input for address A16 and above). PD1 80 I/O CMOS or Open Drain Port D pin PD1 can be configured as: 1. MCU I/O 2. Input to the PLD (can also be PLD input for address A16 and above). 3. CLKIN clock input — clock input to the GPLD Micro⇔Cells, the APD power down counter and GPLD AND Array. PD2 1 I/O CMOS or Open Drain Port D pin PD2 can be configured as: 1. MCU I/O 2. Input to the PLD (can also be PLD input for address A16 and above). 3. CSI input — chip select input. When low, the CSI enables the internal PSD memories and I/O. When high, the internal memories are disabled to conserve power. CSI trailing edge can get the part out of power-down mode. PD3 2 I/O CMOS or Open Drain Port D pin PD3 can be configured as: 1. MCU I/O 2. Input to the PLD (can also be PLD input for address A16 and above). 3. WRH — for 16-bit data bus, write to high byte, active low. PE0 71 I/O CMOS or Open Drain Port E, PE0. This port is pin configurable and has multiple functions: 1. MCU I/O — standard output or input port. 2. Latched address output. 3. TMS input for JTAG/ISP interface. 9 PSD4000 Series Table 5. PSD4000 Pin Descriptions Preliminary Information Pin* (TQFP Pin Name Pkg.) Description PE1 72 I/O CMOS or Open Drain Port E, PE1. This port is pin configurable and has multiple functions: 1. MCU I/O — standard output or input port. 2. Latched address output. 3. TCK input for JTAG/ISP interface (Schmidt Trigger). PE2 73 I/O CMOS or Open Drain Port E, PE2. This port is pin configurable and has multiple functions: 1. MCU I/O — standard output or input port. 2. Latched address output. 3. TDI input for JTAG/ISP interface. PE3 74 I/O CMOS or Open Drain Port E, PE3. This port is pin configurable and has multiple functions: 1. MCU I/O — standard output or input port. 2. Latched address output. 3. TDO output for JTAG/ISP interface. PE4 75 I/O CMOS or Open Drain Port E, PE4. This port is pin configurable and has multiple functions: 1. MCU I/O — standard output or input port. 2. Latched address output. 3. TSTAT output for the ISP interface. 4. Rdy/Bsy — for in-circuit Parallel Programming. PE5 76 I/O CMOS or Open Drain Port E, PE5. This port is pin configurable and has multiple functions: 1. MCU I/O — standard output or input port. 2. Latched address output. 3. TERR active low output for ISP interface. PE6 77 I/O CMOS or Open Drain Port E, PE6. This port is pin configurable and has multiple functions: 1. MCU I/O — standard output or input port. 2. Latched address output. 3. Vstby — SRAM standby voltage input for battery backup SRAM PE7 78 I/O CMOS or Open Drain Port E, PE7. This port is pin configurable and has multiple functions: 1. MCU I/O — standard output or input port. 2. Latched address output. 3. Vbaton — battery backup indicator output. Goes high when power is drawn from an external battery. 31-38 I/O CMOS or Open Drain Port F, PF0-7. This port is pin configurable and has multiple functions: 1. MCU I/O — standard output or input port. 2. Input to the PLD. 3. Latched address outputs. 4. As address A1-3 inputs in 80C51XA mode (PF0 is grounded) 5. As data bus port (D0-7) in non-multiplexed bus configuration 6. MCU reset mode. PG0-PG7 21-28 I/O CMOS or Open Drain Port G, PG0-7. This port is pin configurable and has multiple functions: 1. MCU I/O — standard output or input port. 2. Latched address outputs. 3. As data bus port (D8-15) in non-multiplexed bus configuration. 4. MCU reset mode. (cont.) PF0-PF7 10 Type GND 8,30, 49,50, 70 VCC 9,29, 69 Preliminary Information 7.0 PSD4000 Register Description and Address Offset PSD4000 Series Table 6 shows the offset addresses to the PSD4000 registers relative to the CSIOP base address. The CSIOP space is the 256 bytes of address that is allocated by the user to the internal PSD4000 registers. Table 6 provides brief descriptions of the registers in CSIOP space. For a more detailed description, refer to section 9. Table 6. Register Address Offset Register Name Data In Port A Port B Port C Port D Port E Port F Port G 00 01 10 11 30 40 41 32 42 43 Control Data Out 04 05 14 15 34 44 45 Direction 06 07 16 17 36 46 47 Drive Select 08 09 18 19 38 48 49 Flash Protection Other* C0 Flash Boot Protection C2 PMMR0 B0 PMMR2 B4 Page E0 VM E2 Memory_ID0 F0 Memory_ID1 F1 Description Reads Port pin as input, MCU I/O input mode Selects mode between MCU I/O or Address Out Stores data for output to Port pins, MCU I/O output mode Configures Port pin as input or output Configures Port pins as either CMOS or Open Drain on some pins, while selecting high slew rate on other pins. Read only – Flash Sector Protection Read only – PSD Security and Flash Boot Sector Protection Power Management Register 0 Power Management Register 2 Page Register Places PSD memory areas in Program and/or Data space on an individual basis. Read only – Flash and SRAM size Read only – Boot type and size 11 PSD4000 Series 8.0 Register Bit Definition Preliminary Information All the registers in the PSD4000 are included here for reference. Detail description of the registers are found in the Functional Block section of the Data Sheet. Data In Registers – Port A, B, C, D, E, F and G Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Port Pin 7 Port Pin 6 Port Pin 5 Port Pin 4 Port Pin 3 Port Pin 2 Bit 1 Bit 0 Port Pin 1 Port Pin 0 Bit definitions: Read only registers, read Port pin status when Port is in MCU I/O input Mode. Data Out Registers – Port A, B, C, D, E, F and G Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Port Pin 7 Port Pin 6 Port Pin 5 Port Pin 4 Port Pin 3 Port Pin 2 Bit 1 Bit 0 Port Pin 1 Port Pin 0 Bit definitions: Latched data for output to Port pin when pin is configured in MCU I/O output mode. Direction Registers – Port A, B, C, D, E, F and G Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Port Pin 7 Port Pin 6 Port Pin 5 Port Pin 4 Port Pin 3 Port Pin 2 Bit 1 Bit 0 Port Pin 1 Port Pin 0 Bit definitions: Set Register Bit to 0 = configure corresponding Port pin in Input mode (default). Set Register Bit to 1 = configure corresponding Port pin in Output mode. Control Registers – Ports E, F and G Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Port Pin 7 Port Pin 6 Port Pin 5 Port Pin 4 Port Pin 3 Port Pin 2 Bit 1 Bit 0 Port Pin 1 Port Pin 0 Bit definitions: Set Register Bit to 0 = configure corresponding Port pin in MCU I/O mode (default). Set Register Bit to 1 = configure corresponding Port pin in Latched Address Out mode. Drive Registers – Ports A, B, D, E, and G Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Port Pin 7 Port Pin 6 Port Pin 5 Port Pin 4 Port Pin 3 Port Pin 2 Bit 1 Bit 0 Port Pin 1 Port Pin 0 Bit definitions: Set Register Bit to 0 = configure corresponding Port pin in CMOS output driver (default). Set Register Bit to 1 = configure corresponding Port pin in Open Drain output driver. Drive Registers – Ports C and F Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Port Pin 7 Port Pin 6 Port Pin 5 Port Pin 4 Port Pin 3 Port Pin 2 Bit 1 Bit 0 Port Pin 1 Port Pin 0 Bit definitions: Set Register Bit to 0 = configure corresponding Port pin as CMOS output driver (default). Set Register Bit to 1 = configure corresponding Port pin in Slew Rate mode. Flash Protection Register Bit 7 Sec7_Prot Bit 6 Bit 5 Bit 4 Sec6_Prot Sec5_Prot Sec4_Prot Bit 3 Bit 1 Bit 0 Sec3_Prot Sec2_Prot Sec1_Prot Sec0_Prot Bit definitions: Read Only Register Sec<i>_Prot 1 = Flash Sector <i> is write protected. Sec<i>_Prot 0 = Flash Sector <i> is not write protected. 12 Bit 2 Preliminary Information 8.0 Register Bit Definition (cont.) PSD4000 Series Flash Boot Protection Register Bit 7 Bit 6 Bit 5 Bit 4 Security_Bit * * * Bit 3 Bit 2 Bit 1 Bit 0 Sec3_Prot Sec2_Prot Sec1_Prot Sec0_Prot Bit definitions: Sec<i>_Prot 1 = Boot Block Sector <i> is write protected. Sec<i>_Prot 0 = Boot Block Sector <i> is not write protected. Security_Bit 0 = Security Bit in device has not been set. 1 = Security Bit in device has been set. Page Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Pgr7 Pgr6 Pgr5 Pgr4 Pgr3 Pgr2 Pgr1 Pgr0 Bit definitions: Configure Page input to PLD. Default Pgr[7:0] = 00. PMMR0 Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 * * PLD Mcells clk PLD array-clk PLD Turbo * APD enable * * Not used bit should be set to zero. Bit definitions: (default is 0) Bit 1 0 = Automatic Power Down (APD) is disabled. 1 = Automatic Power Down (APD) is enabled. Bit 3 0 = PLD Turbo is on. 1 = PLD Turbo is off, saving power. Bit 4 0 = CLKIN input to the PLD AND array is connected. Every CLKIN change will power up the PLD when Turbo bit is off. 1 = CLKIN input to PLD AND array is disconnected, saving power. Bit 5 0 = CLKIN input to the PLD Micro⇔Cells is connected. 1 = CLKIN input to the PLD Micro⇔Cells is disconnected, saving power. PMMR2 Register Bit 7 Bit 6 Bit 5 * PLD array WRh PLD array Ale Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 * * PLD PLD PLD array Cntl2 array Cntl1 array Cntl0 * Not used bit should be set to zero. Bit definitions (defauld is 0): Bit 0 0 = Address A[7:0] are connected into the PLD array. 1 = Address A[7:0] are blocked from the PLD array, saving power. Note: in XA mode, A3-0 come from PF3-0 and A7-4 come from ADIO7-4. Bit 2 0 = Cntl0 input to the PLD AND array is connected. 1 = Cntl0 input to the PLD AND array is disconnected, saving power. Bit 3 0 = Cntl1 input to the PLD AND array is connected. 1 = Cntl1 input to the PLD AND array is disconnected, saving power. Bit 4 0 = Cntl2 input to the PLD AND array is connected. 1 = Cntl2 input to the PLD AND array is disconnected, saving power. Bit 5 0 = Ale input to the PLD AND array is connected. 1 = Ale input to the PLD AND array is disconnected, saving power. Bit 6 0 = WRh/DBE input to the PLD AND array is connected. 1 = WRh/DBE input to the PLD AND array is disconnected, saving power. 13 PSD4000 Series 8.0 Register Bit Definition (cont.) Preliminary Information VM Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 * * * FL_data Boot_data FL_code Bit 1 Bit 0 Boot_code SR_code Note: Upon reset, Bit1-Bit4 are loaded to configurations selected by the user in PSDsoft. Bit 0 is always cleared by reset. Bit 0 to Bit 4 are active only when the device is configured in Philips 80C51XA mode. Not used bit should be set to zero. Bit definitions: Bit 0 0 = PSEN can’t access SRAM in 80C51XA modes. 1 = PSEN can access SRAM in 80C51XA modes. Bit 1 0 = PSEN can’t access Boot in 80C51XA modes. 1 = PSEN can access Boot in 80C51XA modes. Bit 2 0 = PSEN can’t access main Flash in 80C51XA modes. 1 = PSEN can access main Flash in 80C51XA modes. Bit 3 0 = RD can’t access Boot in 80C51XA modes. 1 = RD can access Boot in 80C51XA modes. Bit 4 0 = RD can’t access main Flash in 80C51XA modes. 1 = RD can access main Flash in 80C51XA modes. Memory_ID0 Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 S_size 3 S_size 2 S_size 1 S_size 0 F_size 3 F_size 2 F_size 1 F_size 0 Bit definitions: F_size[3:0] = 4h, main Flash size is 2M bit. F_size[3:0] = 5h, main Flash size is 8M bit. S_size[3:0] = 0h, SRAM size is 0K bit. S_size[3:0] = 1h, SRAM size is 16K bit. S_size[3:0] = 3h, SRAM size is 64K bit. Memory_ID1 Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 * * B_type 1 B_type 0 B_size 3 B_size 2 B_size 1 B_size 0 * Not used bit should be set to zero. Bit definitions: B_size[3:0] = 0h, Boot block size is 0K bit. B_size[3:0] = 2h, Boot block size is 256K bit. B_type[1:0] = 0h, Boot block is Flash memory. 14 Preliminary Information 9.0 The PSD4000 Functional Blocks PSD4000 Series As shown in Figure 1, the PSD4000 consists of six major types of functional blocks: ❏ ❏ ❏ ❏ ❏ ❏ Memory Blocks PLD Blocks Bus Interface I/O Ports Power Management Unit JTAG-ISP Interface The functions of each block are described in the following sections. Many of the blocks perform multiple functions, and are user configurable. 9.1 Memory Blocks The PSD4000 has the following memory blocks: • The main Flash memory • Secondary Flash memory • SRAM. The memory select signals for these blocks originate from the Decode PLD (DPLD) and are user-defined in PSDsoft. Table 7 summarizes which versions of the PSD4000 contain which memory blocks. Table 7. Memory Blocks Main Flash Secondary Flash Device Flash Size Sector Size Block Size Sector Size SRAM PSD4135G2 512KB 64KB 32KB 8KB 8KB 9.1.1 Main Flash and Secondary Flash Memory Description The main Flash memory block is divided evenly into eight sectors. The secondary Flash memory is divided into four sectors of eight Kbytes each. Each sector of either memory can be separately protected from program and erase operations. Flash memory may be erased on a sector-by-sector basis and programmed word-by-word. Flash sector erasure may be suspended while data is read from other sectors of memory and then resumed after reading. During a program or erase of Flash, the status can be output on the Rdy/Bsy pin of Port PE4. This pin is set up using PSDsoft. 9.1.1.1 Memory Block Selects The decode PLD in the PSD4000 generates the chip selects for all the internal memory blocks (refer to the PLD section). Each of the eight Flash memory sectors have a Flash Select signal (FS0-FS7) which can contain up to three product terms. Each of the four Secondary Flash memory sectors have a Select signal (CSBOOT0-3) which can contain up to three product terms. Having three product terms for each sector select signal allows a given sector to be mapped in different areas of system memory. When using a microcontroller (80C51XA) with separate Program and Data space, these flexible select signals allow dynamic re-mapping of sectors from one space to the other before and after IAP. 9.1.1.2 The Ready/Busy Pin (PE4) Pin PE4 can be used to output the Ready/Busy status of the PSD4000. The output on the pin will be a ‘0’ (Busy) when Flash memory blocks are being written to, or when the Flash memory block is being erased. The output will be a ‘1’ (Ready) when no write or erase operation is in progress. 15 PSD4000 Series The PSD4000 Functional Blocks (cont.) Preliminary Information 9.1.1.3 Memory Operation The main Flash and secondary Flash memories are addressed through the microcontroller interface on the PSD4000 device. The microcontroller can access these memories in one of two ways: ❏ The microcontroller can execute a typical bus write or read operation just as it would if accessing a RAM or ROM device using standard bus cycles. ❏ The microcontroller can execute a specific instruction that consists of several write and read operations. This involves writing specific data patterns to special addresses within the Flash to invoke an embedded algorithm. These instructions are summarized in Table 8. Typically, Flash memory can be read by the microcontroller using read operations, just as it would read a ROM device. However, Flash memory can only be erased and programmed with specific instructions. For example, the microcontroller cannot write a single word directly to Flash memory as one would write a word to RAM. To program a word into Flash memory, the microcontroller must execute a program instruction sequence, then test the status of the programming event. This status test is achieved by a read operation or polling the Rdy/Busy pin (PE4). The Flash memory can also be read by using special instructions to retrieve particular Flash device information (sector protect status and ID). 9.1.1.3.1 Instructions An instruction is defined as a sequence of specific operations. Each received byte is sequentially decoded by the PSD and not executed as a standard write operation. The instruction is executed when the correct number of bytes are properly received and the time between two consecutive bytes is shorter than the time-out value. Some instructions are structured to include read operations after the initial write operations. The sequencing of any instruction must be followed exactly. Any invalid combination of instruction bytes or time-out between two consecutive bytes while addressing Flash memory will reset the device logic into a read array mode (Flash memory reads like a ROM device). The PSD4000 main Flash and secondary Flash support these instructions (see Table 8): ❏ ❏ ❏ ❏ ❏ ❏ ❏ Erase memory by chip or sector Suspend or resume sector erase Program a word Reset to read array mode Read Main Flash Identifier value Read sector protection status Bypass Instruction These instructions are detailed in Table 8. For efficient decoding of the instructions, the first two bytes of an instruction are the coded cycles and are followed by a command byte or confirmation byte. The coded cycles consist of writing the data byte AAh to address XAAAh during the first cycle and data byte 55h to address X554h during the second cycle (unless the Bypass Instruction feature is used. See 9.1.1.7). Address lines A15-A12 are don’t care during the instruction write cycles. However, the appropriate sector select signal (FSi or CSBOOTi) must be selected. The main Flash and the secondary Flash Block have the same set of instructions (except Read main Flash ID). The chip selects of the Flash memory will determine which Flash will receive and execute the instruction. The main Flash is selected if any one of the FS0-7 is active, and the secondary Flash Block is selected if any one of the CSBOOT0-3 is active. 16 Preliminary Information The PSD4000 Functional Blocks (cont.) PSD4000 Series Table 8. Instructions Instruction (Note 14) FS0-7 or CSBOOT0-3 Cycle 1 Cycle 2 Cycle 3 Cycle 4 Cycle5 Cycle 6 Cycle 7 AAh @XAAAh 55h @X554h 30h @SA 30h @next SA (Note 7) AAh @XAAAh 55h @X554h 10h @XAAAh Read (Note 5) 1 Read Main Flash ID (Note 6) 1 AAh 55h 90h @XAAAh @X554h @XAAAh Read Sector Protection (Notes 6,8,13) 1 AAh 55h 90h “Read” @XAAAh @X554h @XAAAh 00h or 01h @XX04h Program a Flash Word 1 AAh 55h A0h @XAAAh @X554h @XAAAh PD@PA Erase One Flash Sector 1 AAh 55h 80h @XAAAh @X554h @XAAAh Erase Flash Block (Bulk Erase) 1 AAh 55h 80h @XAAAh @X554h @XAAAh Suspend Sector Erase (Note 11) 1 B0h @xxxh Resume Sector Erase (Note 12) 1 30h @xxxh Reset (Note 6) 1 F0 @ any address Unlock Bypass 1 AAh 55h 20h @XAAAh @X554h @XAAAh Unlock Bypass Program (Note 9) 1 A0h PD@PA @XXXXh Unlock Bypass Reset (Note 10) 1 90h 00h @XXXXh @XXXXh X RA RD PA “Read” RA RD “Read” ID @XX02h = = = = Don’t Care. “xxxh” address in the above table must be an even address. Address of the memory location to be read. Data read from location RA during read operation. Address of the memory location to be programmed. Addresses are latched on the falling edge of the WR# (CNTL0) pulse. PA is an even address for PSD in word programming mode. PD = Data (word) to be programmed at location PA. Data is latched on the rising edge of WR# (CNTL0) pulse. SA = Address of the sector to be erased or verified. The chip select (FS0-7 or CSBOOT0-3) of the sector to be erased must be active (high). NOTES: 1. All bus cycles are write bus cycle except the ones with the “read” label. 2. All values are in hexadecimal. 3. FS0-7 and CSBOOT0-3 are active high and are defined in PSDsoft. 4. Only Address bits A11-A0 are used in Instruction decoding. 5. No unlock or command cycles required when device is in read mode. 6. The Reset command is required to return to the read mode after reading the Flash ID, Sector Protect status or if DQ5 (DQ13) goes high. 7. Additional sectors to be erased must be entered within 80µs. 8. The data is 00h for an unprotected sector and 01h for a protected sector. In the fourth cycle, the sector chip select is active and (A1 = 1, A0 = 0). 9. The Unlock Bypass command is required prior to the Unlock Bypass Program command. 10. The Unlock Bypass Reset command is required to return to reading array data when the device is in the Unlock Bypass mode. 11. The system may read and program functions in non-erasing sectors, read the Flash ID or read the Sector Protect status, when in the Erase Suspend mode. The erase Suspend command is valid only during a sector erase operation. 12. The Erase Resume command is valid only during the Erase Suspend mode. 13. The MCU cannot invoke these instructions while executing code from the same Flash memory for which the instruction is intended. The MCU must fetch, for example, codes from the Secondary Flash memory when reading the Sector Protection Status of the main Flash. 14. All write bus cycles in an instruction are byte write to even address (XA4Ah or X554h). Flash Programming bys cycle is writing a word to even address. 17 PSD4000 Series The PSD4000 Functional Blocks (cont.) Preliminary Information 9.1.1.4 Power-Up Condition The PSD4000 internal logic is reset upon power-up to the read array mode. The FSi and CSBOOTi select signals, along with the write strobe signal, must be in the false state during power-up for maximum security of the data contents and to remove the possibility of data being written on the first edge of a write strobe signal. Any write cycle initiation is locked when VCC is below VLKO. 9.1.1.5 Read Under typical conditions, the microcontroller may read the Flash, or secondary Flash memories using read operations just as it would a ROM or RAM device. Alternately, the microcontoller may use read operations to obtain status information about a program or erase operation in progress. Lastly, the microcontroller may use instructions to read special data from these memories. The following sections describe these read functions. 9.1.1.5.1 Read the Contents of Memory Main Flash and secodary Flash memories are placed in the read array mode after power-up, chip reset, or a Reset Flash instruction (see Table 8). The microcontroller can read the memory contents of main Flash or secondary Flash by using read operations any time the read operation is not part of an instruction sequence. 9.1.1.5.2 Read the Main Flash Memory Identifier The main Flash memory identifier is read with an instruction composed of 4 operations: 3 specific write operations and a read operation (see Table 8). The PSD4000 main Flash memory ID is E8h. The Secondary Flash does not support this instruction. 9.1.1.5.3 Read the Flash Memory Sector Protection Status The Flash memory sector protection status is read with an instruction composed of 4 operations: 3 specific write operations and a read operation (see Table 8). The read operation will produce 01h if the Flash sector is protected, or 00h if the sector is not protected. The sector protection status for all NVM blocks (main Flash or secondary Flash) can also be read by the microcontroller accessing the Flash Protection and Flash Boot Protection registers in PSD I/O space. See section 9.1.1.9.1 for register definitions. 9.1.1.5.4 Read the Erase/Program Status Bits The PSD4000 provides several status bits to be used by the microcontroller to confirm the completion of an erase or programming instruction of Flash memory. These status bits minimize the time that the microcontroller spends performing these tasks and are defined in Table 9. The status byte resides in even location and can be read as many times as needed. Please note DQ15-8 is even byte for Motorola MCUs with 16 bit data bus. Table 9. Status Bits Flash FSi/ CSBOOTi DQ7 DQ6 DQ5 DQ4 DQ3 DQ2 DQ1 DQ0 VIH Data Polling Toggle Flag Error Flag X Erase Timeout X X X DQ13 DQ12 DQ11 DQ10 DQ9 DQ8 X Erase Timeout X X X Table 9A. Status Bits for Motorola FSi/ CSBOOTi Flash VIH DQ15 Data Polling DQ14 Toggle Flag Error Flag NOTES: 1. X = Not guaranteed value, can be read either 1 or 0. 2. DQ15-DQ0 represent the Data Bus bits, D15-D0. 3. FSi/CSBOOTi are active high. For Flash memory, the microcontroller can perform a read operation to obtain these status bits while an erase or program instruction is being executed by the embedded algorithm. See section 9.1.1.6 for details. 18 Preliminary Information The PSD4000 Functional Blocks (cont.) PSD4000 Series 9.1.1.5.5 Data Polling Flag DQ7 (DQ15 for Motorola) When Erasing or Programming the Flash memory bit DQ7 (DQ15) outputs the complement of the bit being entered for Programming/Writing on DQ7 (DQ15). Once the Program instruction or the Write operation is completed, the true logic value is read on DQ7 (DQ15) (in a Read operation). Flash memory specific features: ❏ Data Polling is effective after the fourth Write pulse (for programming) or after the ❏ ❏ ❏ sixth Write pulse (for Erase). It must be performed at the address being programmed or at an address within the Flash sector being erased. During an Erase instruction, DQ7 (DQ15) outputs a ‘0’. After completion of the instruction, DQ7 (DQ15) will output the last bit programmed (it is a ‘1’ after erasing). If the location to be programmed is in a protected Flash sector, the instruction is ignored. If all the Flash sectors to be erased are protected, DQ7 (DQ15) will be set to ‘0’ for about 100 µs, and then return to the previous addressed location. No erasure will be performed. 9.1.1.5.6 Toggle Flag DQ6 (DQ14 for Motorola) The PSD4000 offers another way for determining when the Flash memory Program instruction is completed. During the internal Write operation and when either the FSi or CSBOOTi is true, the DQ6 (DQ14) will toggle from ‘0’ to ‘1’ and ‘1’ to ‘0’ on subsequent attempts to read any word of the memory. When the internal cycle is complete, the toggling will stop and the data read on the Data Bus is the addressed memory location. The device is now accessible for a new Read or Write operation. The operation is finished when two successive reads yield the same output data. Flash memory specific features: ❏ The Toggle bit is effective after the fourth Write pulse (for programming) or after the ❏ ❏ sixth Write pulse (for Erase). If the location to be programmed belongs to a protected Flash sector, the instruction is ignored. If all the Flash sectors selected for erasure are protected, DQ6 (DQ14) will toggle to ‘0’ for about 100 µs and then return to the previous addressed location. 9.1.1.5.7 Error Flag DQ5 (DQ14 for Motorola) During a correct Program or Erase, the Error bit will set to ‘0’. This bit is set to ‘1’ when there is a failure during Flash programming, Sector erase, or Bulk Erase. In the case of Flash programming, the Error Bit indicates the attempt to program a Flash bit(s) from the programmed state (0) to the erased state (1), which is not a valid operation. The Error bit may also indicate a timeout condition while attempting to program a word. In case of an error in Flash sector erase or word program, the Flash sector in which the error occurred or to which the programmed location belongs must no longer be used. Other Flash sectors may still be used. The Error bit resets after the Reset instruction. A reset instruction is required after detecting the error bit. 9.1.1.5.8 Erase Time-out Flag DQ3 (DQ11 for Motorola) The Erase Timer bit reflects the time-out period allowed between two consecutive Sector Erase instructions. The Erase timer bit is set to ‘0’ after a Sector Erase instruction for a time period of 100 µs + 20% unless an additional Sector Erase instruction is decoded. After this time period or when the additional Sector Erase instruction is decoded, DQ3 (DQ11) is set to ‘1’. A reset instruction is required after detecting the erase timer bit. 19 PSD4000 Series The PSD4000 Functional Blocks (cont.) Preliminary Information 9.1.1.6 Programming Flash Memory Flash memory must be erased prior to being programmed. The MCU may erase Flash memory all at once or by-sector. Flash memory sector erases to all logic ones, and its bits are programmed to logic zeros. Although erasing Flash memory occurs on a sector or chip basis, programming Flash memory occurs on a word basis. The PSD4000 main Flash and secondary Flash memories require the MCU to send an instruction to program a word or perform an erase function (see Table 8). Once the MCU issues a Flash memory program or erase instruction, it must check for the status of completion. The embedded algorithms that are invoked inside the PSD4000 support several means to provide status to the MCU. Status may be checked using any of three methods: Data Polling, Data Toggle, or the Ready/Busy output pin. 9.1.1.6.1 Data Polling Polling on DQ7 (DQ15) is a method of checking whether a Program or Erase instruction is in progress or has completed. Figure 3 shows the Data Polling algorithm. When the MCU issues a programming instruction, the embedded algorithm within the PSD4000 begins. The MCU then reads the location of the word to be programmed in Flash to check status. Data bit DQ7 (DQ15) of this location becomes the compliment of data bit 7of the original data word to be programmed. The MCU continues to poll this location, comparing DQ7 (DQ15) and monitoring the Error bit on DQ5 (DQ13). When the DQ7 (DQ15) matches data bit 7 of the original data, and the Error bit at DQ5 (DQ13) remains ‘0’, then the embedded algorithm is complete. If the Error bit at DQ5 is ‘1’, the MCU should test DQ7 (DQ15) again since DQ7 (DQ15) may have changed simultaneously with DQ5 (DQ13) (see Figure 3). The Error bit at DQ5 (DQ13) will be set if either an internal timeout occurred while the embedded algorithm attempted to program the location or if the MCU attempted to program a ‘1’ to a bit that was not erased (not erased is logic ‘0’). It is suggested (as with all Flash memories) to read the location again after the embedded programming algorithm has completed to compare the word that was written to Flash with the word that was intended to be written. When using the Data Polling method after an erase instruction, Figure 3 still applies. However, DQ7 (DQ15) will be ‘0’ until the erase operation is complete. A ‘1’ on DQ5 (DQ13) will indicate a timeout failure of the erase operation, a ‘0’ indicates no error. The MCU can read any location within the sector being erased to get DQ7 (DQ15) and DQ5 (DQ13) . PSDsoft generates ANSI C code functions which implement these Data Polling algorithms. 20 Preliminary Information The PSD4000 Functional Blocks PSD4000 Series Figure 3. Data Polling Flow Chart START (cont.) READ DQ5 & DQ7 (DQ13 & DQ15) at VALID EVEN ADDRESS DQ7 (DQ15) = DATA7 (DATA15) YES NO NO DQ5 (DQ13) =1 YES READ DQ7 (DQ15) DQ7 (DQ15) = DATA7 (DATA15) YES NO FAIL Program/Erase Operation Failed Issue Reset Instruction PASS Program/Erase Operation is Completed 9.1.1.6.2 Data Toggle Checking the Data Toggle bit on DQ6 (DQ14) is a method of determining whether a Program or Erase instruction is in progress or has completed. Figure 4 shows the Data Toggle algorithm. When the MCU issues a programming instruction, the embedded algorithm within the PSD4000 begins. The MCU then reads the location to be programmed in Flash to check status. Data bit DQ6 (DQ14) of this location will toggle each time the MCU reads this location until the embedded algorithm is complete. The MCU continues to read this location, checking DQ6 (DQ14) and monitoring the Error bit on DQ5 (DQ13) . When DQ6 (DQ14) stops toggling (two consecutive reads yield the same value), and the Error bit on DQ5 (DQ13) remains ‘0’, then the embedded algorithm is complete. If the Error bit on DQ5 (DQ13) is ‘1’, the MCU should test DQ6 (DQ14) again, since DQ6 (DQ14) may have changed simultaneously with DQ5 (DQ13) (see Figure 4). The Error bit at DQ5 (DQ13) will be set if either an internal timeout occurred while the embedded algorithm attempted to program, or if the MCU attempted to program a ‘1’ to a bit that was not erased (not erased is logic ‘0’). 21 PSD4000 Series Preliminary Information The PSD4000 Functional Blocks 9.1.1.6.2 Data Toggle (cont.) It is suggested (as with all Flash memories) to read the location again after the embedded programming algorithm has completed to compare the word that was written to Flash with the word that was intended to be written. (cont.) When using the Data Toggle method after an erase instructin, Figure 4 still applies. DQ6 (DQ14) will toggle until the erase operation is complete. A ‘1’ on DQ5 (DQ13) will indicate a timeout failure of the erase operation, a ‘0’ indicates no error. The MCU can read any even location within the sector being erased to get DQ6 (DQ14) and DQ5 (DQ13) . PSDsoft generates ANSI C code functions which implement these Data Toggling algorithms. Figure 4. Data Toggle Flow Chart START READ DQ5 & DQ6 (DQ13 & DQ14) at VALID EVEN ADDRESS DQ6 (DQ14) = TOGGLE NO YES NO DQ5 (DQ13) =1 YES READ DQ6 (DQ14) DQ6 (DQ14) = TOGGLE NO YES FAIL Program/Erase Operation Failed Issue Reset Instruction 22 PASS Program/Erase Operation is Completed Preliminary Information The PSD4000 Functional Blocks (cont.) PSD4000 Series 9.1.1.7 Unlock Bypass Instruction The unlock bypass feature allows the system to program words to the flash memories faster than using the standard program instruction. The unlock bypass instruction is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the unlock bypass command, 20h (see Table 8). The flash memory then enters the unlock bypass mode. A two-cycle Unlock Bypass Program instruction is all that is required to program in this mode. The first cycle in this instruction contains the unlock bypass programm command, A0h; the second cycle contains the program address and data. Additional data is programmed in the same manner. This mode dispenses with the initial two unlock cycles required in the standard program instruction, resulting in faster total programming time. During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset instructions are valid. To exit the unlock bypass mode, the system must issue the two-cycle unlock bypass reset instruction. The first cycle must contain the data 90h; the second cycle the data 00h. Addresses are don’t care for both cycles. The flash memory then returns to reading array data mode. 9.1.1.8 Erasing Flash Memory 9.1.1.8.1. Flash Bulk Erase Instruction The Flash Bulk Erase instruction uses six write operations followed by a Read operation of the status register, as described in Table 8. If any byte of the Bulk Erase instruction is wrong, the Bulk Erase instruction aborts and the device is reset to the Read Flash memory status. During a Bulk Erase, the memory status may be checked by reading status bits DQ5, DQ6, and DQ7 (DQ13, DQ14, DQ15), as detailed in section 9.1.1.6. The Error bit (returns a ‘1’ if there has been an Erase Failure (maximum number of erase cycles have been executed). It is not necessary to program the array with 00h because the PSD4000 will automatically do this before erasing to 0FFh. During execution of the Bulk Erase instruction, the Flash memory will not accept any instructions. 9.1.1.8.2 Flash Sector Erase Instruction The Sector Erase instruction uses six write operations, as described in Table 8. Additional Flash Sector Erase confirm commands and Flash sector addresses can be written subsequently to erase other Flash sectors in parallel, without further coded cycles, if the additional instruction is transmitted in a shorter time than the timeout period of about 100 µs. The input of a new Sector Erase instruction will restart the time-out period. The status of the internal timer can be monitored through the level of DQ3 (DQ11) (Erase time-out bit). If DQ3 (DQ11) is ‘0’, the Sector Erase instruction has been received and the timeout is counting. If DQ3 (DQ11) is ‘1’, the timeout has expired and the PSD4000 is busy erasing the Flash sector(s). Before and during Erase timeout, any instruction other than Erase suspend and Erase Resume will abort the instruction and reset the device to Read Array mode. It is not necessary to program the Flash sector with 00h as the PSD4000 will do this automatically before erasing. During a Sector Erase, the memory status may be checked by reading status bits DQ5, DQ6, and DQ7 (DQ13, DQ14, DQ15), as detailed in section 9.1.1.6. During execution of the erase instruction, the Flash block logic accepts only Reset and Erase Suspend instructions. Erasure of one Flash sector may be suspended, in order to read data from another Flash sector, and then resumed. 23 PSD4000 Series The PSD4000 Functional Blocks (cont.) Preliminary Information 9.1.1.8.3 Flash Erase Suspend Instruction When a Flash Sector Erase operation is in progress, the Erase Suspend instruction will suspend the operation by writing 0B0h to any even address when an appropriate Chip Select (FSi or CSBOOTi) is true. (See Table 8). This allows reading of data from another Flash sector after the Erase operation has been suspended. Erase suspend is accepted only during the Flash Sector Erase instruction execution and defaults to read array mode. An Erase Suspend instruction executed during an Erase timeout will, in addition to suspending the erase, terminate the time out. The Toggle Bit DQ6 stops toggling when the PSD4000 internal logic is suspended. The toggle Bit status must be monitored at an address within the Flash sector being erased. The Toggle Bit will stop toggling between 0.1 µs and 15 µs after the Erase Suspend instruction has been executed. The PSD4000 will then automatically be set to Read Flash Block Memory Array mode. If an Erase Suspend instruction was executed, the following rules apply: • Attempting to read from a Flash sector that was being erased will output invalid data. • Reading from a Flash sector that was not being erased is valid. • The Flash memory cannot be programmed, and will only respond to Erase Resume and Reset instructions (read is an operation and is OK). • If a Reset instruction is received, data in the Flash sector that was being erased will be invalid. 9.1.1.8.4 Flash Erase Resume Instruction If an Erase Suspend instruction was previously executed, the erase operation may be resumed by this instruction. The Erase Resume instruction consists of writing 030h to any even address while an appropriate Chip Select (FSi or CSBOOTi) is true. (See Table 8.) 9.1.1.9 Specific Features 9.1.1.9.1 Main Flash and Secondary Flash Sector Protect Each sector of Main Flash and Secondary Flash memory can be separately protected against Program and Erase functions. Sector Protection provides additional data security because it disables all program or erase operations. This mode can be activated (or deactivated) through the JTAG-ISP Port or a Device Programmer. Sector protection can be selected for each sector using the PSDsoft program. This will automatically protect selected sectors when the device is programmed through the JTAG Port or a Device Programmer. Flash sectors can be unprotected to allow updating of their contents using the JTAG Port or a Device Programmer. The microcontroller can read (but cannot change) the sector protection bits. Any attempt to program or erase a protected Flash sector will be ignored by the device. The Verify operation will result in a read of the protected data. This allows a guarantee of the retention of the Protection status. The sector protection status can either be read by the MCU through the Flash protection and secondary Flash protection registers (CSIOP), or use the Read Sector Protection instruction (Table 8). 24 Preliminary Information The PSD4000 Functional Blocks (cont.) PSD4000 Series Table 10. Sector Protection/Security Bit Definition Flash Protection Register Bit 7 Sec7_Prot Bit 6 Bit 5 Bit 4 Sec6_Prot Sec5_Prot Sec4_Prot Bit Definitions: Sec<i>_Prot Sec<i>_Prot Bit 3 Bit 2 Bit 1 Bit 0 Sec3_Prot Sec2_Prot Sec1_Prot Sec0_Prot 1 = Main Flash Sector <i> is write protected. 0 = Main Flash Sector <i> is not write protected. Flash Boot Protection Register *: Bit 7 Bit 6 Bit 5 Bit 4 Security_ Bit * * * Bit 3 Bit 2 Bit 1 Bit 0 Sec3_Prot Sec2_Prot Sec1_Prot Sec0_Prot Not used. Bit Definitions: Sec<i>_Prot Sec<i>_Prot Security_Bit 1 = Flash Boot Sector <i> is write protected. 0 = Flash Boot Sector <i> is not write protected. 0 = Security Bit in device has not been set. 1 = Security Bit in device has been set. 9.1.1.9.2 Reset Instruction The Reset instruction consists of one write cycle (see Table 8). It can also be optionally preceded by the standard two write decoding cycles (writing AAh to AAAh and 55h to 554h). The Reset instruction must be executed after: 1. Reading the Flash Protection status or Flash ID using the Flash instruction. 2. When an error condition occurs (DQ5 (DQ13) goes high) during a Flash programming or erase cycle. The Reset instruction will reset the Flash to normal Read Mode immediately. However, if there is an error condition (DQ5 (DQ13) goes high), the Flash memory will return to the Read Mode in 25 µSeconds after the Reset instruction is issued. The Reset instruction is ignored when it is issued during a Flash programming or Bulk Erase cycle. The Reset instruction will abort the on going sector erase cycle and return the Flash memory to normal Read Mode in 25 µSeconds. 9.1.1.9.3 Reset Pin Input The reset pulse input from the pin will abort any operation in progress and reset the Flash memory to Read Mode. When the reset occurs during a programming or erase cycle, the Flash memory will take up to 25 µSeconds to return to Read Mode. It is recommended that the reset pulse (except power on reset, see Reset Section) be at least 25 µSeconds such that the Flash memory will always be ready for the MCU to fetch the boot code after reset is over. 25 PSD4000 Series The PSD4000 Functional Blocks (cont.) Preliminary Information 9.1.2 SRAM The SRAM is enabled when RS0— the SRAM chip select output from the DPLD— is high. RS0 can contain up to three product terms, allowing flexible memory mapping. The SRAM can be backed up using an external battery. The external battery should be connected to the Vstby pin (PE6). If you have an external battery connected to the PSD4000, the contents of the SRAM will be retained in the event of a power loss. The contents of the SRAM will be retained so long as the battery voltage remains at 2V or greater. If the supply voltage falls below the battery voltage, an internal power switchover to the battery occurs. Pin PE7 can be configured as an output that indicates when power is being drawn from the external battery. This Vbaton signal will be high with the supply voltage falls below the battery voltage and the battery on PE6 is supplying power to the internal SRAM. The chip select signal (RS0) for the SRAM, Vstby, and Vbaton are all configured using PSDsoft. 9.1.3 Memory Select Signals The main Flash (FSi), secondary Flash (CSBOOTi), and SRAM (RS0) memory select signals are all outputs of the DPLD. They are defined using PSDsoft. The following rules apply to the equations for the internal chip select signals: 1. Main Flash memory and secondary Flash memory sector select signals must not be larger than the physical sector size. 2. Any main Flash memory sector must not be mapped in the same memory space as another Main Flash sector. 3. A secondary Flash memory sector must not be mapped in the same memory space as another Flash Boot sector. 4. SRAMand I/O spaces must not overlap. 5. A secondary Flash memory sector may overlap a main Flash memory sector. In case of overlap, priority will be given to the Flash Boot sector. 6. SRAM, I/O, and Peripheral I/O spaces may overlap any other memory sector. Priority will be given to the SRAM, and I/O. Example FS0 is valid when the address is in the range of 8000h to BFFFh, CSBOOT0 is valid from 8000h to 9FFFh, and RS0 is valid from 8000h to 87FFh. Any address in the range of RS0 will always access the SRAM. Any address in the range of CSBOOT0 greater than 87FFh (and less than 9FFFh) will automatically address Boot memory segment 0. Any address greater than 9FFFh will access the Flash memory segment 0. You can see that half of the Flash memory segment 0 and one-fourth of Boot segment 0 can not be accessed in this example. Also note that an equation that defined FS1 to anywhere in the range of 8000h to BFFFh would not be valid. Figure 5 shows the priority levels for all memory components. Any component on a higher level can overlap and has priority over any component on a lower level. Components on the same level must not overlap. Level one has the highest priority and level 3 has the lowest. 26 Preliminary Information The PSD4000 Functional Blocks PSD4000 Series Figure 5. Priority Level of Memory and I/O Components (cont.) Highest Priority Level 1 SRAM, I/O Level 2 Secondary Flash Memory Level 3 Main Flash Memory Lowest Priority 9.1.3.1. Memory Select Configuration for MCUs with Separate Program and Data Spaces The 80C51XA and compatible family of microcontrollers, can be configured to have separate address spaces for code memory (selected using PSEN) and data memory (selected using RD). Any of the memories within the PSD4000 can reside in either space or both spaces. This is controlled through manipulation of the VM register that resides in the PSD’s CSIOP space. The VM register is set using PSDsoft to have an initial value. It can subsequently be changed by the microcontroller so that memory mapping can be changed on-the-fly. For example, you may wish to have SRAM and main Flash in Data Space at boot, and secondary Flash memory in Program Space at boot, and later swap main and secondary Flash memory. This is easily done with the VM register by using PSDsoft to configure it for boot up and having the microcontroller change it when desired. Table 11 describes the VM Register. Table 11. VM Register Bit 7 PIO_EN Bit 6* Bit 5* Bit 4 Bit 3 FL_Data Boot_Data Bit 2 FL_Code Bit 1 Bit 0 Boot_Code SRAM_Code 0 = disable PIO mode * * 0 = RD can’t access Flash 0 = RD can’t access Boot Flash 0 = PSEN can’t access Flash 0 = PSEN can’t access Boot Flash 0 = PSEN can’t access SRAM 1= enable PIO mode * * 1 = RD access Flash 1 = RD access Boot Flash 1 = PSEN 1 = PSEN access access Flash Boot Flash 1 = PSEN access SRAM NOTE: Bits 6-5 are not used. 27 PSD4000 Series The PSD4000 Functional Blocks (cont.) Preliminary Information 9.1.3.2 Configuration Modes for MCUs with Separate Program and Data Spaces 9.1.3.2.1 Separate Space Modes Code memory space is separated from data memory space. For example, the PSEN signal is used to access the program code from the main Flash Memory, while the RD signal is used to access data from the secondary Flash memory, SRAM and I/O Ports. This configuration requires the VM register to be set to 0Ch. 9.1.3.2.2 . Combined Space Modes The program and data memory spaces are combined into one space that allows the main Flash Memory, secondary Flash memory, and SRAM to be accessed by either PSEN or RD. For example, to configure the main Flash memory in combined space mode, bits 2 and 4 of the VM register are set to “1”. 9.1.3.3 80C51XA Memory Map Example See Application Notes for examples. Figure 6. 80C51XA Memory Modes – Separate Space Mode DPLD SRAM FLASH BOOT BLOCK MAIN FLASH RS0 CSBOOT0-3 FS0-7 CS CS OE CS OE OE PSEN RD Figure 7. 80C51XA Memory Mode – Combined Space Mode DPLD RD RS0 FLASH BOOT BLOCK MAIN FLASH CSBOOT0-3 FS0-7 CS CS OE VM REG BIT 4 PSEN VM REG BIT 1 VM REG BIT 0 28 CS OE VM REG BIT 3 VM REG BIT 2 SRAM RD OE Preliminary Information The PSD4000 Functional Blocks (cont.) PSD4000 Series 9.1.4 Page Register The eight bit Page Register increases the addressing capability of the microcontroller by a factor of up to 256. The contents of the register can also be read by the microcontroller. The outputs of the Page Register (PGR0-PGR7) are inputs to the PLD decoder and can be included in the Flash Memory, secondary Flash memory, and SRAM chip select equations. If memory paging is not needed, or if not all 8 page register bits are needed for memory paging, then these bits may be used in the PLD for general logic. See Application Notes. Figure 8 shows the Page Register. The eight flip flops in the register are connected to the internal data bus. The microcontroller can write to or read from the Page Register. The Page Register can be accessed at address location CSIOP + E0h. Figure 8. Page Register RESET DATA BUS D0 Q0 D1 Q1 D2 Q2 D3 Q3 D4 Q4 D5 Q5 D6 Q6 D7 Q7 PGR0 INTERNAL SELECTS AND LOGIC PGR1 PGR2 PGR3 PGR4 DPLD AND GPLD PGR5 PGR6 PGR7 R/W PAGE REGISTER FLASH PLD 29 PSD4000 Series Preliminary Information The PSD4000 Functional Blocks 9.1.5 Memory ID Registers (cont.) Memory_ID0 Register The 8-bit read only memory status registers are included in the CSIOP space. The user can determine the memory configuration of the PSD device by reading the Memory ID0 and Memory ID1 registers. The content of the registers are defined as follow: Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 S_size 3 S_size 2 S_size 1 S_size 0 F_size 3 F_size 2 F_size 1 F_size 0 Bit Definition F_size3 F_size2 F_size1 F_size0 Main Flash Size (Bit) 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 none 256K 512K 1M 2M 4M 8M S_size3 S_size2 S_size1 S_size0 SRAM Size (Bit) 0 0 0 0 0 0 0 0 0 0 1 1 0 1 0 1 none 16K 32K 64K Memory_ID1 Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 * * B_type 1 B_type 0 B_size 3 B_size 2 B_size 1 B_size 0 * Not used bit should be set to zero. Bit Definition 30 B_size3 B_size2 B_size1 B_size0 Boot Block Size (Bit) 0 0 0 0 0 0 0 0 0 0 1 1 0 1 0 1 none 128K 256K 512K B_type1 B_type0 Boot Block Type 0 0 0 1 Flash EEPROM Preliminary Information PSD4000 Series The PSD4000 Functional Blocks 9.2 PLDs (cont.) The PSD4000 contains two PLDs: the Decode PLD (DPLD), and the General Purpose PLD (GPLD). The PLDs are briefly discussed in the next few paragraphs, and in more detail in sections 9.2.1 and 9.2.2. Figure 10 shows the configuration of the PLDs. The PLDs bring programmable logic functionality to the PSD4000. After specifying the logic for the PLDs in PSDsoft, the logic is programmed into the device and available upon power-up. The DPLD performs address decoding for internal components, such as memory, registers, and I/O port selects. The GPLD can be used to generate external chip selects, control signals or logic functions. The GPLD has 24 outputs that are connected to Port A, B and C. The AND array is used to form product terms. These product terms are specified using PSDsoft. An Input Bus consisting of 66 signals is connected to the PLDs. The signals are shown in Table 12. The complement of the 66 signals are also available as inputs to the AND array. Table 12. DPLD and GPLD Inputs Input Source Input Name Number of Signals MCU Address Bus A[15:0]* 16 MCU Control Signals CNTL[2:0] 3 Reset RST 1 Power Down PDN 1 Port A Input PA[7-0] 8 Port B Input PB[7-0] 8 Port C Input PC[7-0] 8 Port D Inputs PD[3:0] 4 Port F Inputs PF[7:0] 8 Page Register PGR(7:0) 8 Flash Programming Status Bit Rdy/Bsy 1 NOTE: The address inputs are A[19:4] in 80C51XA mode. The Turbo Bit The PLDs in the PSD4000 can minimize power consumption by switching to standby when inputs remain unchanged for an extended time of about 70 ns. Setting the Turbo mode bit to off (Bit 3 of the PMMR0 register) automatically places the PLDs into standby if no inputs are changing. Turbo-off mode increases propagation delays while reducing power consumption. Refer to the Power Management Unit section on how to set the Turbo Bit. Additionally, five bits are available in the PMMR2 register to block MCU control signals from entering the PLDs. This reduces power consumption and can be used only when these MCU control signals are not used in PLD logic equations. 31 PSD4000 Series Preliminary Information Figure 9. PLD Block Diagram 8 PAGE REGISTER DATA BUS 8 DECODE PLD 66 FLASH MEMORY SELECTS 4 FLASH BOOT MEMORY SELECTS 1 SRAM SELECT PLD INPUT BUS 1 CSIOP SELECT GENERAL PURPOSE PLD GPLD PLD OUT 8 PORT A 66 PLD OUT 8 PORT B PLD OUT 8 PORT C 32 PORT A PLD INPUT 8 PORT B PLD INPUT 8 PORT C PLD INPUT 8 PORT D PLD INPUT 4 PORT F PLD INPUT 8 PORT D PORT F Preliminary Information The PSD4000 Functional Blocks (cont.) PSD4000 Series 9.2.1 Decode PLD (DPLD) The DPLD, shown in Figure 10, is used for decoding the address for internal components. The DPLD can generate the following decode signals: • • • • 8 4 1 1 sector selects for the main Flash memory (three product terms each) sector selects for the Secondary Flash memory (three product terms each) internal SRAM select (three product terms) internal CSIOP select (select PSD registers, one product term) Inputs to the DPLD chip selects may include address inputs, Page Register inputs and other user defined external inputs from Ports A, B, C, D or F. 9.2.2 General Purpose PLD (GPLD) The General Purpose PLD implements user defined system combinatorial logic function or chip selects for external devices. Figure 11 shows how the GPLD is connected to the I/O Ports. The GPLD has 24 outputs and each are routed to a port pin. The port pin can also be configured as input to the GPLD. When it is not used as GPLD output or input, the pin can be configured to perform other I/O functions. All GPLD outputs are identical except in the number of available product terms (PTs) for logic implementation. Select the pin that can best meet the PT requirement of your logic function or chip select. In general, a PT is consumed for each logic “OR” function that you specify in PSDsoft. However, certain logic functions can consume more than one PT even if no logic “OR” is specified (such as specifying an address range with boundaries of high granularity). Table 13 shows the number of “native” PTs for each GPLD output pin. A native PT means that a particular PT is dedicated to an output pin. For example, Table 13 shows that PSD Port A pin PA0 has 3 native product terms. This means a guaranteed minimum of 3 PTs is available to implement logic for that pin. PSD silicon and PSDsoft can include additional PTs beyong the native PTs to implement logic. This is a transparent operation that occurs as needed through PT expansion (internal feedback) or PT allocation (internal borrowing). You may notice in the fitter report generated by PSDsoft that for a given GPLD output pin, more PTs were used to implement logic than the number of native PTs available for that pin. This is because PSDsoft has called on unused PTs from other GPLD output pins to make your logic design fit (PT allocation or PT expansion). For optimum results, choose a GPLD output pin with a large number of native PTs for complicated logic. Table 13. GPLD Product Term Availability GPLD Output on Port Pin Port A, Port A, Port B, Port B, Port C, pins pins pins pins pins PA0-3 PA4-7 PB0-3 PB4-7 PC0-7 Number of Native Product Terms 3 9 4 7 1 33 3 CSBOOT 1 3 CSBOOT 2 3 CSBOOT 3 3 4 SECONDARY FLASH MEMORY SECTOR SELECTS PSD4000 Series CSBOOT 0 Figure 10. DPLD Logic Array 34 3 FS0 3 (INPUTS) I /O PORTS (PORT A,B,C,F) 3 (32) 3 PGR0 - PGR7 8 FLASH MEMORY SECTOR SELECTS (8) 3 A[15:0] * (16) 3 PD[3:0] (ALE,CLKIN,CSI) (4) PDN (APD OUTPUT) (1) CNTRL[2:0] (READ/WRITE CONTROL SIGNALS) (3) RESET (1) RD_BSY (1) 3 3 3 FS7 RS0 CSIOP 1. The address inputs are A[19:4] in 80C51XA mode. 2. Additional address lines can be brought into PSD via Port A, B, C, C or F. I/O DECODER SELECT Preliminary Information *NOTES: SRAM SELECT PLD INPUT BUS AND ARRAY AND ARRAY AND ARRAY POLARITY SELECT POLARITY SELECT POLARITY SELECT PIN PC0-7 HAS 1 NATIVE PT PRODUCT TERM * PIN PB0-3 HAS 4 NATIVE PTs PIN PB4-7 HAS 7 NATIVE PTs PRODUCT TERM * PIN PA0-3 HAS 3 NATIVE PTs PIN PA4-7 HAS 9 NATIVE PTs PRODUCT TERM * GENERAL PURPOSE PLD (GPLD) PLD OUTPUT PLD OUTPUT PLD OUTPUT OTHER I/O FUNCTION OTHER I/O FUNCTION OTHER I/O FUNCTION PLD INPUT MUX PLD INPUT MUX PLD INPUT MUX I/O PORT PORT C PORT B PORT A Preliminary Information PSD4000 Series Figure 11. The Micro⇔Cell and I/O Port 35 PSD4000 Series The PSD4000 Functional Blocks (cont.) Preliminary Information 9.3 Microcontroller Bus Interface The “no-glue logic” PSD4000 Microcontroller Bus Interface can be directly connected to most popular microcontrollers and their control signals. Key 16-bit microcontrollers with their bus types and control signals are shown in Table 14. The MCU interface type is specified using the PSDsoft. Table 14. Microcontrollers and their Control Signals MCU CNTL0 CNTL1 CNTL2 PD3 PD0** ADIO0 PF3-PF0 68302, 68306 MMC2001 R/W LDS UDS * AS – * 68330, 68331 68332, 68340 R/W DS SIZ0 * AS A0 * 68LC302, MMC2001 WEL OE WEH AS – * 68HC16 R/W DS SIZ0 * AS A0 68HC912 R/W E LSTRB DBE E A0 68HC812*** R/W E LSTRB * A0 80196 WR RD BHE * * ALE A0 80196SP WRL RD * WRH ALE A0 80186 WR RD BHE * ALE A0 * * * * * * 80C161 80C164-80C167 WR RD BHE * ALE A0 * 80C51XA WRL RD PSEN WRH ALE A4/D0 A3-A1 H8/3044 WRL RD * WRH AS A0 – M37702M2 R/W E BHE * ALE A0 * ***Unused CNTL2 pin can be configured as GPLD input. Other unused pins (PD3-0, PF3-0) can be ***configured for other I/O functions. ***ALE/AS input is optional for microcontrollers with a non-multiplexed bus. ***This configuration is for 68C812A4_EC at 5MHz, 3V only. 9.3.1. PSD4000 Interface to a Multiplexed Bus Figure 16 shows an example of a system using a microcontroller with a 16-bit multiplexed bus and a PSD4000. The ADIO port on the PSD4000 is connected directly to the microcontroller address/data bus. ALE latches the address lines internally. Latched addresses can be brought out to Port E, F or G. The PSD4000 drives the ADIO data bus only when one of its internal resources is accessed and the RD input is active. Should the system address bus exceed sixteen bits, Ports A, B, C, or F may be used as additional address inputs. 9.3.2. PSD4000 Interface to a Non-Multiplexed Bus Figure 17 shows an example of a system using a microcontroller with a 16-bit non-multiplexed bus and a PSD4000. The address bus is connected to the ADIO Port, and the data bus is connected to Port F and G. Port F and G are in tri-state mode when the PSD4000 is not accessed by the microcontroller. Should the system address bus exceed sixteen bits, Ports A, B or C may be used for additional address inputs. 36 Preliminary Information The PSD4000 Functional Blocks PSD4000 Series Figure 12. An Example of a Typical 16-Bit Multiplexed Bus Interface (cont.) PSD4135G2 MICROCONTROLLER AD[ 7:0] ADIO PORT AD[ 15:8] WR WR (CNTRL0) RD RD (CNTRL1) BHE (CNTRL2) BHE RST ALE A [ 7: 0] PORT F (OPTIONAL) PORT G (OPTIONAL) PORT A,B, or C (OPTIONAL) A [ 15: 8] A [ 23:16] ALE (PD0) PORT D RESET Figure 13. An Example of a Typical 16-Bit Non-Multiplexed Bus Interface PSD4135G2 D [ 15:0] MICROCONTROLLER ADIO PORT PORT F D [ 7:0] A [ 15:0] PORT G WR WR (CNTRL0) RD RD (CNTRL1) BHE (CNTRL2) BHE RST ALE PORT A,B or C D[ 15:8] (OPTIONAL) A[ 23:16] (OPTIONAL) ALE (PD0) PORT D RESET 37 PSD4000 Series The PSD4000 Functional Blocks (cont.) Preliminary Information 9.3.3 Data Byte Enable Reference Microcontrollers have different data byte orientations. The following tables show how the PSD4135G2 interprets byte/word operation in different bus write configurations. Even-byte refers to locations with address A0 equal to zero and odd byte as locations with A0 equal to one. 9.3.4 Microcontroller Interface Examples Figures 14 through 17 show examples of the basic connections between the PSD4135G2 and some popular microcontrollers. The PSD4135G2 Control input pins are labeled as the microcontroller function for which they are configured. The MCU interface is specified using PSDsoft. The PE6 pin should be grounded if Vstby is not used. 9.3.4.1 80C196 and 80C186 In Figure 14, the Intel 80C196 microcontroller, which has a multiplexed sixteen-bit bus, is shown connected to a PSD4135G2. The WR and RD signals are connected to the CNTL0-1 pins. The BHE signal is used for high data byte selection. If BHE is not used, the PSD can be configured to receive the WRL and WRH from the MCU. Higher address inputs (A16-A19) can be routed to Port A, B or C as inputs to the PLD. The AMD 80186 family has the same bus connection to the PSD as the 80C196. Table 15. 16-Bit Data Bus with BHE BHE A0 D15-D8 D7-D0 0 0 Odd Byte Even Byte 0 1 Odd Byte – 1 0 – Even Byte Table 16. 16-Bit Data Bus with WRH and WRL WRH WRL D15-D8 D7-D0 0 0 Odd Byte Even Byte 0 1 Odd Byte – 1 0 – Even Byte Table 17. 16-Bit Data Bus with SIZ0, A0 (Motorola MCU) SIZ0 A0 D15-D8 D7-D0 0 0 Even Byte Odd Byte 1 0 Even Byte – 1 1 – Odd Byte Table 18. 16-Bit Data Bus with UDS, LDS (Motorola MCU) 38 LDS UDS D15-D8 D7-D0 0 0 Even Byte Odd Byte 1 0 Even Byte – 0 1 – Odd Byte Preliminary Information The PSD4000 Functional Blocks PSD4000 Series 9.3.4.2 MC683XX and 68HC16 Figure 15 shows a Motorola MC68331 with non-multiplexed sixteen-bit data bus and 24-bit address bus. The data bus from the MC68331 is connected to Port F (D0-7) and Port G (D8-D15). The SIZ0 and A0 inputs determine the high/low byte selection. The R/W, DS and SIZ0 are connected to the CNTL0-2 pins. (cont.) The 68HC16 and other members of the 683XX family have the same connection as the 68331 shown in Figure 15. 9.3.4.3 80C51XA The Philips 80C51XA microcontroller has a 16-bit multiplexed bus with burst cycles. Address bits A[3:1] are not multiplexed while A[19:4] are multiplexed with data bits D[15:0]. The PSD4135G2 supports the 80C51XA burst mode. The WRH signal is connected to the PD3 and the WRL is connected to CNTL0 pin. The RD and PSEN signal is connected to CNTL1-2 pins. Figure 15 shows the XA schematic. The 80C51XA improves bus throughput and performance by issuing Burst cycles to fetch codes from memory. In Burst cycles, addresses A19-4 are latched internally by the PSD, while the 80C51XA drives the A3-1 lines to sequentially fetch up to 16 bytes of code. The PSD access time is then measured from address A3-A1 valid to data in valid. The PSD bus timing requirement in Burst cycle is identical to the normal bus cycle except the address set up or hold time with respect to ALE is not required. 9.3.4.4 H8/300 Figure 16 shows a Hitachi H8/2350 with non-multiplexed sixteen-bit data bus and 24-bit address bus. The H8 data bus is connected to Port F (D0-7) and Port G (D8-15). The WRL, WRH and RD signals are connected to the CNTL0, PD3 and CNTL1 pins respectively. The AS connection is optional and is required if the address are to be latched. 9.3.4.5 MMC2001 The Motorola MCORE MMC2001 microcontroller has a MOD input pin that selects internal or external boot ROM. The PSD4000 can be configured as the external flash boot ROM or as extension to the internal ROM. The MMC2001 has a 16-bit external data bus and 20 address lines with external Chip Select signals. The Chip Select Control Registers allow the user to customize the bus interface and timing to fit the individual system requirement. A typical interface configuration to the PSD4000 is shown in Figure 18. The MMC2001’s R/W signal is connected to the cntl0 pin, while EB0 and EB1 (enable byte0 and byte1) are connected to the cntl1 (UDS) and cntl2 (LDS) pins. The WEN bit in the Chip Select Control Register should set to 1 to terminate the EB[0:1] earlier to provide the write data hold time for the PSD. The WSC and WWS bits in the Control Register are set to wait states that meet the PSD access time requirement. Another option is to configure the EB0 and EB1 as WRL and WRH signals. In this case the PSD4000 control setting will be: OE, WRL, WRH where OE is the read signal from the MMC2001. 9.3.4.6 C16X Family The PSD4000 supports Infineon’s C16X family of microcontrollers (C161-C167) in both the multiplexed and non-multiplexed bus configuration. In Figure 19 the C167CR is shown connected to the PSD4000 in a multiplexed bus configuration. The control signals from the MCU are WR, RD, BHE and ALE and are routed to the corresponding PSD pins. The C167 has another control signal setting (RD, WRL, WRH, ALE) which is also supported by the PSD4000. 39 40 RESET U3 CRYATAL 50 57 56 55 54 53 52 51 49 6 48 62 63 54 65 36 37 38 39 40 41 42 43 44 45 46 47 58 59 60 61 32 66 67 P1.7/EPA7 P1.0/EPAQ/T2CLK P1.1/EPA1 P1.2/EPA2/T2DIR P1.3/EPA3 P1.4/EPA4 P1.5/EPA5 P1.6/EPA6 VREF VPP ANGND P6.4/SC0 P6.5/6D0 P6.6/SC1 P6.7/SD1 P2.0/TX/PVR P2.1/RXD/PALE P2.2/EXINT/PROG P2.3/INTB P2.4/INTINTOUT P2.5/HLD P2.6/HLDA/CPVER P2.7/CLKOUT/PAC ACH4/P0.4/PMD.0 ACH5/P0.5/PMD.1 ACH6/P0.6/PMD.2 ACH7/P0.7/PMD.3 P6.0/EPA8 P6.1EPA9 P6.2/T1CLK P6.3/T1DIR NMI X2 X1 80C196NT SLPINT/P5.4 BUSWIDTH/P5.7 INST/P5.1 EA READY/P5.6 RESET ALE/ADV/P5.0 BHE/WRH/P5.5 EP.0/A16 EP.1/A17 EP.2/A18 EP.3/A19 WR/WRL/P5.2 RD/P5.3 P4.0/AD8 P4.1/AD9 P4.2/AD10 P4.3/AD11 P4.4/AD12 P4.5/AD13 P4.6/AD14 P4.7/AD15 P3.0/AD0 P3.1/AD1 P3.2/AD2 P3.3/AD3 P3.4/AD4 P3.5/AD5 P3.6/AD6 P3.7/AD7 VCC A16 A17 A18 A19 WR 1 10 3 33 71 72 73 74 75 76 77 78 RESET 31 2 39 ALE 4 40 59 60 13 14 15 16 17 18 19 20 3 4 5 6 7 10 11 12 79 80 1 2 8 BHE RD AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 22 21 20 19 18 17 16 15 14 13 12 11 9 7 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 30 29 28 27 26 25 24 23 9 29 69 VCC VCC VCC 8 30 49 50 70 GND GND GND GND GND PEO (TMS) PE1 (TCK/ST) PE2 (TDI) PD2 (TDO) PE4 (TSTAT/RDY) PE5 (TERR) PE6 (VSTBY) PE7 (VBATON) RESET PDO (ALE) PD1 (CLKIN) PD2 (CSI) PD3 (WRH) CNTL2 (BHE) CRTL0 (WR) CNTL1 (RD) ADIO8 ADI09 ADIO10 ADIO11 ADIO12 ADIO13 ADIO14 ADIO15 ADIO0 ADIO1 ADIO2 ADIO3 ADIO4 ADIO5 ADIO6 ADIO7 PSD4135G2 VCC PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PG0 PG1 PG2 PG3 PG4 PG5 PG6 PG7 PF0 PF1 PF2 PF3 PF4 PF5 PF6 PF7 41 42 43 44 45 46 47 48 61 62 63 64 65 66 67 68 51 52 53 54 55 56 57 58 21 22 23 24 25 26 27 28 31 32 33 34 35 36 37 38 A16 A17 A18 A19 AD[15:0] A[19:16] A[19:16] AD[15:0] PSD4000 Series Preliminary Information Figure 14. Interfacing the PSD4135G2 with an 80C196 RESET 100 99 98 97 94 93 92 91 D8 D9 D10 D11 D12 D13 D14 D15 77 76 75 74 73 72 71 89 88 111 110 109 108 105 104 103 102 D0 D1 D2 D3 D4 D5 D6 D7 IRQ1 IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 DSACK0 DSACK1 D8 D9 D10 D11 D12 D13 D14 D15 D0 D1 D2 D3 D4 D5 D6 D7 MC68331 RESET CSBOOT BR_CSO BG_CS1 BGACK_CS2 FCO_CS3 FC1_CS4 FC2_CS5 CLKOUT SIZ1 RESET AS SIZ0 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19_CS6 A20_CS7 A21_CS8 A22_CS9 A23_CS10 R_W DS A0 A1 A2 A3 A4 A5 A6 A7 R/W 112 113 114 115 118 119 120 66 80 68 82 81 RESET DS AS SIZ0 A8 A9 A10 A11 A12 A13 A14 A15 27 30 31 32 33 35 36 37 38 41 42 121 122 123 124 125 79 85 A16 A17 A18 A19 A20 A21 A22 A23 A0 A1 A2 A3 A4 A5 A6 A7 90 20 21 22 23 24 25 26 71 72 73 74 75 76 77 78 79 80 1 2 39 40 59 60 13 14 15 16 17 18 19 20 3 4 5 6 7 10 11 12 9 29 69 VCC VCC VCC 8 30 49 50 70 GND GND GND GND GND PE0 (TMS) PE1 (TCK/ST) PE2 (TDI) PD3 (TDO) PE4 (TSTAT/RDY) PE5 (TERR) PE6 (VSTBY) PE7 (VBATON) PD0 (AS) PD1 (CLKIN) PD2 (CSI) PD3 RESET CNTL2 (SIZ0) CRTL0 (R/W) CNTL1 (DS) ADIO8 ADIO9 ADIO10 ADIO11 ADIO12 ADIO13 ADIO14 ADIO15 ADIO0 ADIO1 ADIO2 ADIO3 ADIO4 ADIO5 ADIO6 ADIO7 PSD4135G2 VCC PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PG0 PG1 PG2 PG3 PG4 PG5 PG6 PG7 PF0 PF1 PF2 PF3 PF4 PF5 PF6 PF7 41 42 43 44 45 46 47 48 61 62 63 64 65 66 67 68 51 52 53 54 55 56 57 58 21 22 23 24 25 26 27 28 31 32 33 34 35 36 37 38 A16 A17 A18 A19 D8 D9 D10 D11 D12 D13 D14 D15 D0 D1 D2 D3 D4 D5 D6 D7 A[23:0] D[15:0] A[23:0] D[15:0] Preliminary Information PSD4000 Series Figure 15. Interfacing the PSD4135G2 with an MC68331 41 42 RESET VCC RESET CRYATAL XTAL2 XTAL1 17 35 10 14 15 BUSW EA/WAIT RST INT0 INT1 9 T2EX 8 T2 10 T0 11 RXD0 13 TXD0 6 RXD1 7 TXD1 20 21 XA-G3 ALE PSEN A3 A2 A1 A0/WRH WRL RD A12D8 A13D9 A14D10 A15D11 A16D12 A17D13 A18D14 A19D15 A4D0 A5D1 A6D2 A7D3 A8D4 A9D5 A10D6 A11D7 A3 A2 A1 WRH 71 72 73 74 75 76 77 78 39 79 80 1 2 PSEN 32 ALE 40 RD 33 59 60 WRL 13 14 15 16 17 18 19 20 A12D8 A13D9 A14D10 A15D11 A16D12 A17D13 A18D14 A19D15 24 25 26 27 28 29 30 31 5 4 3 2 18 19 3 4 5 6 7 10 11 12 A4D0 A5D1 A6D2 A7D3 A8D4 A9D5 A10D6 A11D7 43 42 41 40 39 38 37 36 9 29 69 VCC VCC VCC 8 30 49 50 70 GND GND GND GND GND PEO (TMS) PE1 (TCK/ST) PE2 (TDI) PD3 (TDO) PE4 (TSTAT/RDY) PE5 (TERR) PE6 (VSTBY) PE7 (VBATON) RESET PD0 (ALE) PD1 (CLKIN) PD2 (CSI) PD3 (WRH) CNTL2 CRTL0 (WR) CNTL1 (RD) ADIO8 ADI09 ADIO10 ADIO11 ADIO12 ADIO13 ADIO14 ADIO15 ADIO0 ADIO1 ADIO2 ADIO3 ADIO4 ADIO5 ADIO6 ADIO7 PSD4135G2 VCC PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PG0 PG1 PG2 PG3 PG4 PG5 PG6 PG7 PF0 PF1 PF2 PF3 PF4 PF5 PF6 PF7 41 42 43 44 45 46 47 48 61 62 63 64 65 66 67 68 51 52 53 54 55 56 57 58 21 22 23 24 25 26 27 28 31 32 33 34 35 36 37 38 A[3:1] A1 A2 A3 D[15:0] A[3:1] D[15:0] PSD4000 Series Preliminary Information Figure 16. Interfacing the PSD4135G2 with a 80C51XA-G3 RESET U3 CRYATAL 43 44 45 46 48 49 50 51 D8 D9 D10 D11 D12 D13 D14 D15 80 113 114 115 88 87 86 74 71 70 69 68 67 66 65 64 60 61 62 63 55 53 57 56 54 58 90 89 91 29 30 31 32 77 78 34 35 36 37 39 40 41 42 D0 D1 D2 D3 D4 D5 D6 D7 PF0/PHI0 MOD0 MOD1 MOD2 PF0/BREQ PF1/BACK PF2/LCAS/WAIT/B NMI PO0/TIOCA3 PO1/TIOCB3 PO2/TIOC3/TMRI PO3/TIOCD3/TMCI PO4/TIOCA4/TMRI PO5/TIOB4/TMRC PO6/TI0C5/TMRO PO7/TIOCB5/TMRO DREQ/CS4 TEND0/CS5 DREQ1 TEND1 RXD0 TXD0 SCK0 PXD1 TXD1 SCK1 RXD2 TXD2 SCK2 CS7/IRQ3 CS6/IRQ2 IRQ1 IRQ0 XTAL EXTAL PD0/D8 PD1/D9 PD2/D10 PD3/D11 PD4/D12 PD5/D13 PD6/D14 PD7/D15 PE0/D0 PE0/D1 PE0/D2 PE0/D3 PE0/D4 PE0/D5 PE0/D6 PE0/D7 H85/2350 RESET PG0/CAS/OE PG1/CS3 PG2/CS2 PG3/CS1 PG4/CS0 AN0 AN1 AN2 AN3 AN4 AN5 AN6/DA0 AN7/DA1 ADTRG PO8/TIOCA0/DACK PO9/TIOCB0/DACK PO10/TIOCC0/TCL PO11/TIOCD0/TCL PO12/TIOCA1 PO13/TIOCB1/TCL PO14/TIOCA2 PO15/TIOCB2/TCL STBY WDTOVF RESET HWR AS PB0/A8 PB1/A9 PB2/A10 PB3/A11 PB4/A12 PB5/A13 PB6/A14 PB7/A15 PA0/A16 PA1/A17 PA2/A18 PB3/A19 PA4/A20/IRQ4 PA5/A21/IRQ5 PA6/A22/IRQ6 PA7/A23/1RQ7 LWR RD PC0/A0 PC1/A1 PC2/A2 PC3/A3 PC4/A4 PC5/A5 PC6/A6 PC7/A7 WRH 84 116 117 118 119 120 95 96 97 98 99 100 101 102 92 112 111 110 109 108 107 106 105 75 72 RESET AS 82 73 RD WRL A8 A9 A10 A11 A12 A13 A14 A15 11 12 13 14 16 17 18 19 20 21 22 23 25 26 27 28 85 83 A16 A17 A18 A19 A20 A21 A22 A23 A0 A1 A2 A3 A4 A5 A6 A7 2 3 4 5 7 8 9 10 71 72 73 74 75 76 77 78 39 79 80 1 2 40 59 60 13 14 15 16 17 18 19 20 3 4 5 6 7 10 11 12 9 29 69 VCC VCC VCC 8 30 49 50 70 GND GND GND GND GND PE0 (TMS) PE1 (TCK/ST) PE2 (TDI) PD3 (TDO) PE4 (TSTAT/RDY) PE5 (TERR) PE6 (VSTBY) PE7 (VBATON) RESET PDO (AS) PD1 (CLKIN) PD2 (CSI) PD3 (WRH) CNTL2 CRTL0 (WRL) CNTL1 (RD) ADIO8 ADIO9 ADIO10 ADIO11 ADIO12 ADIO13 ADIO14 ADIO15 ADIO0 ADIO1 ADIO2 ADIO3 ADIO4 ADIO5 ADIO6 ADIO7 PSD4135G2 VCC PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PG0 PG1 PG2 PG3 PG4 PG5 PG6 PG7 PF0 PF1 PF2 PF3 PF4 PF5 PF6 PF7 41 42 43 44 45 46 47 48 61 62 63 64 65 66 67 68 A16 A17 A18 A19 D8 D9 D10 D11 D12 D13 D14 D15 21 22 23 24 25 26 27 28 51 52 53 54 55 56 57 58 D0 D1 D2 D3 D4 D5 D6 D7 31 32 33 34 35 36 37 38 A[23:0] D[15:0] A[23:0] D[15:0] Preliminary Information PSD4000 Series Figure 17. Interfacing a PSD4135G2 with a H83/2350 43 RESET 32 33 34 35 38 39 40 41 D8 D9 D10 D11 D12 D13 D14 D15 MOD XVDD XGND XGND VBATT VSTBY CLKOUT CLKIN RSTOUT RSTIN LVRSTIN IF GPS_OUT FVDD FGND DE TDO TMS TD1 TCK TRST TEST INT7 INT6 INT5 INT4 INT3 INT2 INT1 INT0 PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 SPI_MISO SPI_MISI SPI_EN SPI_CLK SPI_GP TXD0/PSTAT0 RXD0/PSTAT1 RTS0/PSTAT2 CTS0/PSTAT3 TXD1/SIZ0 RXD1/SIZ1 DATA8 DATA9 DATA10 DATA11 DATA12 DATA13 DATA14 DATA15 DATA0 DATA1 DATA2 DATA3 DATA4 DATA5 DATA6 DATA7 XSOC EXOSC UI RESET 17 18 13 16 10 11 4 5 7 8 9 1 2 3 6 84 83 85 86 87 88 89 93 94 95 96 97 100 101 102 139 140 141 142 143 144 121 124 125 126 128 129 130 131 132 135 136 22 23 24 25 28 29 30 31 15 14 D0 D1 D2 D3 D4 D5 D6 D7 U3 CRYATAL GVDD0 GGND0 99 98 GVDD1 GGND1 110 111 MMC2001 HVDD HGND 122 123 QVCC QVCCH QVCCH QGND DVDD0 DGND0 DVDD1 DGMD1 AVDD1 AGND1 AVDD2 AGND2 QVCC QVCCH QGND CVDD CGND COL7 COL6 COL5 COL4 COL3 COL2 COL1 COL0 ROW7 ROW6 ROW5 ROW4 ROW3 ROW2 ROW1 ROW0 CS0 CS1 CS2 CS3 R/W OE EB1 EB0 ADDR8 ADDR9 ADDR10 ADDR11 ADDR12 ADDR13 ADDR14 ADDR15 ADDR16 ADDR17 ADDR18 ADDR19 ADDR20 ADDR21 ADDR0 ADDR1 ADDR2 ADDR3 ADDR4 ADDR5 ADDR6 ADDR7 NOT USED AGND0 QGND QVCC QVCCH QVCC QGND JVDD JGND 44 127 133 134 137 138 12 46 47 48 19 20 55 21 26 27 36 37 58 59 68 67 92 91 90 78 77 103 104 105 106 107 108 109 112 113 114 115 116 117 118 119 120 75 76 79 80 73 74 82 81 R/W LDS RESET CSO* UDS A8 A9 A10 A11 A12 A13 A14 A15 54 56 57 60 61 62 63 64 65 66 69 70 71 72 A16 A17 A18 A19 A20 A21 A0 A1 A2 A3 A4 A5 A6 A7 42 43 44 45 50 51 52 53 71 72 73 74 75 76 77 78 39 79 80 1 2 40 59 60 13 14 15 16 17 18 19 20 3 4 5 6 7 10 11 12 9 29 69 PSD4135G2 VCC VCC VCC 8 30 49 50 70 GND GND GND GND GND PE0 (TMS) PE1 (TCK/ST) PE2 (TDI) PE3 (TDO) PE4 (TSTAT/RDY) PE5 (TERR) PE6 (VSTBY) PE7 (VBATON) RESET PD0 (AS) PD1 (CLKIN) PD2 (CSI) PD3 CNTL2 (UDS) CRTL0 (R/W) CNTL1 (LDS) ADIO8 ADIO9 ADIO10 ADIO11 ADIO12 ADIO13 ADIO14 ADIO15 ADIO0 ADIO1 ADIO2 ADIO3 ADIO4 ADIO5 ADIO6 ADIO7 U2 VCC PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PG0 PG1 PG2 PG3 PG4 PG5 PG6 PG7 PF0 PF1 PF2 PF3 PF4 PF5 PF6 PF7 41 42 43 44 45 46 47 48 61 62 63 64 65 66 67 68 A16* A17 A18 A19 D8 D9 D10 D11 D12 D13 D14 D15 21 22 23 24 25 26 27 28 51 52 53 54 55 56 57 58 D0 D1 D2 D3 D4 D5 D6 D7 31 32 33 34 35 36 37 38 A[21:0] D[15:0] A[21:0] D[15:0] PSD4000 Series Preliminary Information Figure 18. Interfacing a PSD4135G2 with a MMC2001 RESET 37 97 9 10 11 12 13 14 15 16 19 20 21 22 23 24 25 26 1 2 3 4 5 6 7 8 27 28 29 30 31 32 33 34 35 36 39 40 41 43 44 80 81 65 66 67 68 69 70 73 74 75 76 77 78 137 RESET U3 CRYATAL 138 143 139 127 110 94 VSS VSS VSS VSS VSS Vref READY P8.0/CC16IO P8.1/CC17IO P8.2/CC18IO P8.3/CC19IO P8.4/CC20IO P8.5/CC21IO P8.6/CC22IO P8.7/CC23IO P7.0/POUT0 P7.1/POUT1 P7.2/POUT2 P7.3POUT/3 P7.4/CC28IO P7.5/CC29IO P7.6/CC30IO P7.7/CC31IO P6.0/ CSO P6.1/ CS1 P6.2/ CS2 P6.3/ CS3 P6.4/ CS4 P6.5/ HOLD P6.6/ HLDA P6.7/ BREQ P5.0/AN0 P5.1/AN1 P5.2/AN2 P5.3/AN3 P5.4/AN4 P5.5/AN5 P5.6/AN6 P5.7/AN7 P5.9/AN8 P5.9/AN9 P5.10/AN10/T6UED P5.11/AN11/T5UED P5.12/AN12/T6IN P5.14/AN14/T4UED P5.15/AN15/T2UED P3.13/SCLK P3.15/CLKOUT 71 55 P1H7 P1H6 P1H5 P1H4 P1H3 P1H2 P1H1 P1H0 P1L7 P1L6 P1L5 P1L4 P1L3 P1L2 P1L1 P1L0 EA 45 18 38 AGND RSTIN RSTOUT NMI P2.0/CC0IO P2.1/CC1IO P2.2/CC2IO P2.3/CC3IO P2.4/CC4IO P2.5/CC5IO P2.6/CC6IO P2.7/CC7IO P2.8/CC8IO/EX0IN P2.9/CC9IO/EX1IN P2.10CC10IO/EX2IN P2.11/CC11IO/EX3IN P2.12/CC12IO/EX4IN P2.13/CC13IO/EX5IN P2.14/CC14IO/EX6IN P2.15/CC15IO/EX7IN VSS VSS VSS VSS VSS 83 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 P4.0/A16 A17 A18 A19 A20 A21 A22 P4.7/A23 WR/WRL RD P312/BHE/WRH ALE VCC VCC VCC VCC VCC 82 72 56 46 17 C167CR VCC VCC VCC VCC VCC P3.0/T0IN P3.1/T6OUT P3.2/CAPIN P3.4/T3TOUT P3.4/T3EUD P3.5/T4IN P3.6/T3IN P3.7/T2IN P3.8/MRST P3.10/TXD0 P3.10/TXD0 P3.11/RXD0 XTAL2 XTAL1 144 136 129 109 93 VCC A16 A17 A18 A19 WR RD 99 140 141 142 47 48 49 50 51 52 53 54 57 58 59 60 61 62 63 64 135 134 133 132 131 130 129 128 125 124 123 122 121 120 119 118 RESET BHE ALE AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 108 111 112 113 114 115 116 117 85 86 87 88 89 90 91 92 96 95 79 98 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 100 101 102 103 104 105 106 107 71 72 73 74 75 76 77 78 39 79 80 1 2 40 59 60 13 14 15 16 17 18 19 20 3 4 5 6 7 10 11 12 9 29 69 PSD4135G2 VCC VCC VCC 8 30 49 50 70 GND GND GND GND GND PEO (TMS) PE1 (TCK/ST) PE2 (TDI) PD2 (TDO) PE4 (TSTAT/RDY) PE5 (TERR) PE6 (VSTBY) PE7 (VBATON) RESET PDO (ALE) PD1 (CLKIN) PD2 (CSI) PD3 (WRH) CNTL2 (BHE) CRTL0 (WR) CNTL1 (RD) ADIO8 ADI09 ADIO10 ADIO11 ADIO12 ADIO13 ADIO14 ADIO15 ADIO0 ADIO1 ADIO2 ADIO3 ADIO4 ADIO5 ADIO6 ADIO7 VCC PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PG0 PG1 PG2 PG3 PG4 PG5 PG6 PG7 PF0 PF1 PF2 PF3 PF4 PF5 PF6 PF7 41 42 43 44 45 46 47 48 61 62 63 64 65 66 67 68 51 52 53 54 55 56 57 58 21 22 23 24 25 26 27 28 31 32 33 34 35 36 37 38 A16 A17 A18 A19 AD[15:0] A[19:16] A[19:16] AD[15:0] Preliminary Information PSD4000 Series Figure 19. Interfacing a PSD4135G2 with a C167R 45 PSD4000 Series The PSD4000 Functional Blocks (cont.) Preliminary Information 9.4 I/O Ports There are seven programmable I/O ports: Ports A, B, C, D, E, F and G. Each of the ports is eight bits except Port D, which is 4 bits. Each port pin is individually user configurable, thus allowing multiple functions per port. The ports are configured using PSDsoft or by the microcontroller writing to on-chip registers in the CSIOP address space. The topics discussed in this section are: • General Port Architecture • Port Operating Modes • Port Configuration Registers • Port Data Registers • Individual Port Functionality. 9.4.1 General Port Architecture The general architecture of the I/O Port is shown in Figure 20. Individual Port architectures are shown in Figures 21 through 23. In general, once the purpose for a port pin has been defined, that pin will no longer be available for other purposes. Exceptions will be noted. As shown in Figure 20, the ports contain an output multiplexer whose selects are driven by the configuration bits in the Control Registers (Ports E, F and G only) and PSDsoft Configuration. Inputs to the multiplexer include the following: ❏ Output data from the Data Out Register ❏ Latched address outputs ❏ GPLD outputs (External Chip Selects) The Port Data Buffer (PDB) is a tri-state buffer that allows only one source at a time to be read. The PDB is connected to the Internal Data Bus for feedback and can be read by the microcontroller. The Data Out and Micro⇔Cell outputs, Direction and Control Registers, and port pin input are all connected to the PDB. The contents of these registers can be altered by the microcontroller. The PDB feedback path allows the microcontroller to check the contents of the registers. 9.4.2 Port Operating Modes The I/O Ports have several modes of operation. Some modes can be defined using PSDsoft, some by the microcontroller writing to the Registers in CSIOP space, and some by both. The modes that can only be defined using PSDsoft must be programmed into the device and cannot be changed unless the device is reprogrammed. The modes that can be changed by the microcontroller can be done so dynamically at run-time. The PLD I/O, Data Port, Address Input, and MCU Reset modes are the only modes that must be defined before programming the device. All other modes can be changed by the microcontroller at run-time. Table 16 summarizes which modes are available on each port. Table 19 shows how and where the different modes are configured. Each of the port operating modes are described in the following subsections. 46 Preliminary Information Port Mode Port A Port B Port C Port D Port E Port F Port G MCU I/O Yes Yes Yes Yes Yes Yes Yes PLD Outputs Yes Yes Yes No No No No PLD Inputs Yes Yes Yes Yes No Yes No Address Out No No No No Yes (A7-0) Yes (A7-0) Yes (A7-0) or (A15-8) Address In Yes Yes Yes Yes No Yes No Data Port No No No No No Yes Yes JTAG ISP No No No No Yes No No MCU Reset Mode* No No No No No Yes Yes *Available to Motorola 16-bit 683XX and HC16family of MCUs. OUTPUT SELECT Q D WR DIR REG. Q D WR CONTROL REG. B P D READ MUX G ALE GPLD OUTPUTS Q D ADDRESS WR D Q DATA IN ADDRESS DATA OUT OUTPUT MUX PLD INPUT PORT PIN Figure 20. General I/O Port Architecture DATA OUT REG. (cont.) Table 16. Port Operating Modes INTERNAL DATA BUS The PSD4000 Functional Blocks PSD4000 Series 47 PSD4000 Series The PSD4000 Functional Blocks (cont.) Preliminary Information Table 17. Port Operating Mode Settings Defined In PSDsoft Control Register Setting Direction Register Setting VM Register Setting MCU I/O Declare pins only 0 (Note 1) 1 = output, 0 = input NA PLD I/O Declare pins and logic or chip select equations NA Selected for MCU with non-mux bus NA NA NA Declare pins only 1 1 NA NA NA NA Declare pins only NA NA NA Specify pin logic level NA NA NA Mode Data Port (Port F, G) Address Out (Port E, F, G) Address In (Port A,B,C,D,F) JTAG ISP MCU Reset Mode NA Declare pins *NA = Not Applicable NOTE: 1. Control Register setting is not applicable to Ports A, B and C. 9.4.2.1 MCU I/O Mode In the MCU I/O Mode, the microcontroller uses the PSD4000 ports to expand its own I/O ports. By setting up the CSIOP space, the ports on the PSD4000 are mapped into the microcontroller address space. The addresses of the ports are listed in Table 6. A port pin can be put into MCU I/O mode by writing a ‘0’ to the corresponding bit in the Control Register (Port E, F and G). The MCU I/O direction may be changed by writing to the corresponding bit in the Direction Register. See the subsection on the Direction Register in the “Port Registers” section. When the pin is configured as an output, the content of the Data Out Register drives the pin. When configured as an input, the microcontroller can read the port input through the Data In buffer. See Figure 20. Ports A, B and C do not have Control Registers, and are in MCU I/O mode by default. They can be used for PLD I/O if they are specified in PSDsoft. 9.4.2.2 PLD I/O Mode The PLD I/O Mode uses a port as an input to the CPLD’s Input Micro⇔Cells, and/or as an output from the GPLD. The corresponding bit in the Direction Register must not be set to ‘1’ if the pin is defined as a PLD input pin in PSDsoft. The PLD I/O Mode is specified in PSDsoft by declaring the port pins, and then specifying an equation in PSDsoft. 48 Preliminary Information The PSD4000 Functional Blocks (cont.) PSD4000 Series 9.4.2.3 Address Out Mode For microcontrollers with a multiplexed address/data bus, Address Out Mode can be used to drive latched addresses onto the port pins. These port pins can, in turn, drive external devices. Either the output enable or the corresponding bits of both the Direction Register and Control Register must be set to a ‘1’ for pins to use Address Out Mode. This must be done by the MCU at run-time. See Table 18 for the address output pin assignments on Ports E, F and F for various MCUs. Note: Do not drive address lines with Address Out Mode to an external memory device if it is intended for the MCU to boot from the external device. The MCU must first boot from PSD memory so the Direction and Control register bits can be set. Table 18. I/O Port Latched Address Output Assignments MCU 80C51XA All Other MCU with Multiplexed Bus Port E (3:0) Port E (7:4) Port F (3:0) Port F (7:4) Port G (3:0) Port G (7:4) N/A Addr (7:4) N/A Addr (7:4) Addr (11:8) Addr (15:12) Addr (3:0) Addr (7:4) Addr (3:0) Addr (7:4) Addr (11:8) Addr (15:12) 9.4.2.4 Address In Mode For microcontrollers that have more than 16 address lines, the higher addresses can be connected to Ports A, B, C, D or F and are routed as inputs to the PLDs. The address input can be latched by the address strobe (ALE/AS). Any input that is included in the DPLD equations for the Main Flash, Boot Flash, or SRAM is considered to be an address input. 9.4.2.5 Data Port Mode Port F and G can be used as a data bus port for a microcontroller with a non-multiplexed address/data bus. The Data Port is connected to the data bus of the microcontroller. The general I/O functions are disabled in Port F and G if the ports are configured as Data Port. Data Port Mode is automatically configured in PSDsoft when a non-multiplexed bus MCU is selected. 9.4.2.6 JTAG ISP Port E is JTAG compliant, and can be used for In-System Programming (ISP). 9.4.2.7 MCU Reset Mode Port F and G can be configured to operate in “MCU Reset” mode. This mode is available when PSD is configured for the Motorola 16-bit 683XX and HC16 family and is active only during reset. At the rising edge of the Reset input, the MCU reads the logic level on the Data Bus D15-0 pins. The MCU then configures some of its I/O pin functions according to the logic level input on the data bus lines. Two dedicated buffers are usually enabled during reset to drive the data bus lines to the desired logic level. The PSD4135G2 can replace the two buffers by configuring Port F and G to operate in MCU Reset Mode. In this mode, the PSD will drive the pre-defined logic level or data pattern onto the MCU Data Bus when reset is active and there is no ongoing bus cycle. After reset, Port F and G return to the normal Data Port Mode. The MCU Reset Mode is enabled and configured in PSDsoft. The user defines the logic level (data pattern) that will be driven out from Port F and G during reset. 49 PSD4000 Series The PSD4000 Functional Blocks (cont.) Preliminary Information 9.4.3 Port Configuration Registers (PCRs) Each port has a set of PCRs used for configuration. The contents of the registers can be accessed by the microcontroller through normal read/write bus cycles at the addresses given in Table 6. The addresses in Table 6 are the offsets in hex from the base of the CSIOP register. The pins of a port are individually configurable and each bit in the register controls its respective pin. For example, Bit 0 in a register refers to Bit 0 of its port. The three PCRs, shown in Table 19, are used for setting the port configurations. The default power-up state for each register in Table 22 is 00h. Table 19. Port Configuration Registers Register Name Port MCU Access Control E,F,G Write/Read Direction A,B,C,D,E,F,G Write/Read Drive Select* A,B,C,D,E,F,G Write/Read *NOTE: See Table 22 for Drive Register bit definition. 9.4.3.1 Control Register Any bit set to ‘0’ in the Control Register sets the corresponding Port pin to MCU I/O Mode, and a ‘1’ sets it to Address Out Mode. The default mode is MCU I/O. Only Ports E, F and G have an associated Control Register. 9.4.3.2 Direction Register The Direction Register controls the direction of data flow in the I/O Ports. Any bit set to ‘1’ in the Direction Register will cause the corresponding pin to be an output, and any bit set to ‘0’ will cause it to be an input. The default mode for all port pins is input. Figures 21 and 23 show the Port Architecture diagrams for Ports A/B/C and E/F/G respectively. The direction of data flow for Ports A, B, C and F are controlled by the direction register. An example of a configuration for a port with the three least significant bits set to output and the remainder set to input is shown in Table 21. Since Port D only contains four pins, the Direction Register for Port D has only the four least significant bits active. Table 20. Port Pin Direction Control Direction Register Bit Port Pin Mode 0 1 Input Output Table 21. Port Direction Assignment Example 50 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 1 1 1 Preliminary Information PSD4000 Series The PSD4000 Functional Blocks 9.4.3.3 Drive Select Register The Drive Select Register configures the pin driver as Open Drain or CMOS for some port pins, and controls the slew rate for the other port pins. An external pull-up resistor should be used for pins configured as Open Drain. (cont.) A pin can be configured as Open Drain if its corresponding bit in the Drive Select Register is set to a ‘1’. The default pin drive is CMOS. Aside: the slew rate is a measurement of the rise and fall times of an output. A higher slew rate means a faster output response and may create more electrical noise. A pin operates in a high slew rate when the corresponding bit in the Drive Register is set to ‘1’. The default rate is slow slew. Table 22 shows the Drive Register for Ports A, B, C, D, E, F and G. It summarizes which pins can be configured as Open Drain outputs and which pins the slew rate can be set for. Table 22. Drive Register Pin Assignment Drive Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Port A Open Drain Open Drain Open Drain Open Drain Open Drain Open Drain Open Drain Open Drain Port B Open Drain Open Drain Open Drain Open Drain Open Drain Open Drain Open Drain Open Drain Port C Slew Rate Slew Rate Slew Rate Slew Rate Slew Rate Slew Rate Slew Rate Slew Rate Open Drain Open Drain Open Drain Open Drain Port D Port E Open Drain Open Drain Open Drain Open Drain Open Drain Open Drain Open Drain Open Drain Port F Slew Rate Slew Rate Slew Rate Slew Rate Slew Rate Slew Rate Slew Rate Slew Rate Port G Open Drain Open Drain Open Drain Open Drain Open Drain Open Drain Open Drain Open Drain 9.4.4 Port Data Registers The Port Data Registers, shown in Table 23, are used by the microcontroller to write data to or read data from the ports. Table 23 shows the register name, the ports having each register type, and microcontroller access for each register type. The registers are described below. 9.4.4.1 Data In Port pins are connected directly to the Data In buffer. In MCU I/O input mode, the pin input is read through the Data In buffer. 9.4.4.2 Data Out Register Stores output data written by the MCU in the MCU I/O output mode. The contents of the Register are driven out to the pins if the Direction Register or the output enable product term is set to “1”. The contents of the register can also be read back by the microcontroller. Table 27. Port Data Registers Register Name Port MCU Access Data In A,B,C,D,E,F,G Read – input on pin Data Out A,B,C,D,E,F,G Write/Read 51 PSD4000 Series The PSD4000 Functional Blocks (cont.) Preliminary Information 9.4.5 Ports A, B and C – Functionality and Structure Ports A and B have similar functionality and structure, as shown in Figure 21. The two ports can be configured to perform one or more of the following functions: ❏ ❏ ❏ ❏ ❏ MCU I/O Mode GPLD Output – Combinatorial PLD outputs. PLD Input – Input to the PLDs. Address In – Additional high address inputs may be latched by ALE. Open Drain/Slew Rate – pins PC[7:0]can be configured to fast slew rate, pins PA[7:0] and PB[7:0] can be configured to Open Drain Mode. Figure 21. Port A, B and C DATA OUT REG. D Q DATA OUT WR PORT PIN OUTPUT MUX GPLD OUTPUT INTERNAL DATA BUS READ MUX P OUTPUT SELECT D DATA IN B DIR REG. D Q WR PLD INPUT 52 Preliminary Information (cont.) 9.4.6 Port D – Functionality and Structure Port D has four I/O pins. See Figure 22. Port D can be configured to program one or more of the following functions: ❏ MCU I/O Mode ❏ PLD Input – direct input to PLD Port D pins can be configured in PSDsoft as input pins for other dedicated functions: ❏ PD0 – ALE, as address strobe input ❏ PD1 – CLKIN, as clock input to the PLD and APD counter ❏ PD2 – CSI, as active low chip select input. A high input will disable the Flash/SRAM and CSIOP. ❏ PD3 – WRH, as active low Write Enable (high byte) input or as DBE input from 68HC912 9.4.7 Port E – Functionality and Structure Port E can be configured to perform one or more of the following functions (see Figure 23): ❏ MCU I/O Mode ❏ In-System Programming – JTAG port can be enabled for programming/erase of the ❏ ❏ ❏ PSD4000 device. (See Section 9.6 for more information on JTAG programming.) Pins that are configured as JTAG pins in PSDsoft will not be available for other I/O functions. Open Drain – Port E pins can be configured in Open Drain Mode Battery Backup features – PE6 can be configured as a Battery Input (Vstby) pin. PE7 can be configured as a Battery On Indicator output pin, indicating when Vcc is less than Vbat. Latched Address Output – Provided latched address (A7-0) output Figure 22. Port D Structure DATA OUT REG. DATA OUT D Q WR PORT D PIN OUTPUT MUX READ MUX INTERNAL DATA BUS The PSD4000 Functional Blocks PSD4000 Series OUTPUT SELECT P D DATA IN B DIR REG. D WR Q PLD INPUT 53 PSD4000 Series The PSD4000 Functional Blocks (cont.) Preliminary Information 9.4.8 Port F – Functionality and Structure Port F can be configured to perform one or more of the following functions: ❏ ❏ ❏ ❏ ❏ ❏ ❏ MCU I/O Mode PLD Input – as direct input ot the PLD array. Address In – additional high address inputs. Direct input to the PLD array. Latched Address Out – Provide latched address out per Table 29. Slew Rate – pins can be set up for fast slew rate. Data Port – connected to D[7:0] when Port F is configured as Data Port for a non-multiplexed bus. MCU Reset Mode – for 16-bit Motorola 683XX and HC16 microcontrollers. 9.4.9 Port G – Functionality and Structure Port G can be configured to perform one or more of the following functions: ❏ ❏ ❏ ❏ ❏ MCU I/O Mode Latched Address Out – provide latched address out per Table 29. Open Drain – pins can be configured in Open Drain Mode Data Port – connected to D[15:8] when Port G is configured as Data Port for a non-multiplexed bus. MCU Reset Mode – for 16-bit Motorola 683XX and HC16 microcontrollers Figure 23. Ports E, F and G Structure DATA OUT REG. D Q D Q DATA OUT WR ADDRESS ALE ADDRESS A[ 7:0] OR A[15:8] G PORT PIN OUTPUT MUX INTERNAL DATA BUS READ MUX P OUTPUT SELECT D DATA IN B CONTROL REG. D Q WR DIR REG. D Q WR PLD INPUT (PORT F) ISP OR BATTERY BACK-UP (PORT E) CONFIGURATION BIT 54 Preliminary Information The PSD4000 Functional Blocks (cont.) PSD4000 Series 9.5 Power Management The PSD4000 offers configurable power saving options. These options may be used individually or in combinations, as follows: ❏ All memory types in a PSD (Flash, Secondary Flash, and SRAM) are built with Zero-Power technology. In addition to using special silicon design methodology, Zero-Power technology puts the memories into standby mode when address/data inputs are not changing (zero DC current). As soon as a transition occurs on an input, the affected memory “wakes up”, changes and latches its outputs, then goes back to standby. The designer does not have to do anything special to achieve memory standby mode when no inputs are changing—it happens automatically. The PLD sections can also achieve standby mode when its inputs are not changing, see PMMR registers below. ❏ Like the Zero-Power feature, the Automatic Power Down (APD) logic allows the PSD to reduce to standby current automatically. The APD will block MCU address/data signals from reaching the memories and PLDs. This feature is available on all PSD4000 devices. The APD unit is described in more detail in section 9.5.1. Built in logic will monitor the address strobe of the MCU for activity. If there is no activity for a certain time period (MCU is asleep), the APD logic initiates Power Down Mode (if enabled). Once in Power Down Mode, all address/data signals are blocked from reaching PSD memories and PLDs, and the memories are deselected internally. This allows the memories and PLDs to remain in standby mode even if the address/data lines are changing state externally (noise, other devices on the MCU bus, etc.). Keep in mind that any unblocked PLD input signals that are changing states keeps the PLD out of standby mode, but not the memories. ❏ The PSD Chip Select Input (CSI) can be used to disable the internal memories, placing them in standby mode even if inputs are changing. This feature does not block any internal signals or disable the PLDs. This is a good alternative to using the APD logic, especially if your MCU has a chip select output. There is a slight penalty in memory access time when the CSI signal makes its initial transition from deselected to selected. ❏ The PMMR registers can be written by the MCU at run-time to manage power. All PSD devices support “blocking bits” in these registers that are set to block designated signals from reaching both PLDs. Current consumption of the PLDs is directly related to the composite frequency of the changes on their inputs (see Figures 27 and 27a). Significant power savings can be achieved by blocking signals that are not used in PLD logic equations at run time. PSDsoft creates a fuse map that automatically blocks the low address byte (A7-A0) or the control signals (CNTL0-2, ALE and WRH/DBE) if none of these signals are used in PLD logic equations. The PSD4000 devices have a Turbo Bit in the PMMR0 register. This bit can be set to disable the Turbo Mode feature (default is Turbo Mode on). While Turbo Mode is disabled, the PLDs can achieve standby current when no PLD inputs are changing (zero DC current). Even when inputs do change, significant power can be saved at lower frequencies (AC current), compared to when Turbo Mode is enabled. Conversely, when the Turbo Mode is enabled, there is a significant DC current component and the AC component is higher. 9.5.1 Automatic Power Down (APD) Unit and Power Down Mode The APD Unit, shown in Figure 24, puts the PSD into Power Down Mode by monitoring the activity of the address strobe (ALE/AS). If the APD unit is enabled, as soon as activity on the address strobe stops, a four bit counter starts counting. If the address strobe remains inactive for fifteen clock periods of the CLKIN signal, the Power Down (PDN) signal becomes active, and the PSD will enter into Power Down Mode, discussed next. 55 PSD4000 Series The PSD4000 Functional Blocks (cont.) Preliminary Information 9.5.1 Automatic Power Down (APD) Unit and Power Down Mode (cont.) Power Down Mode By default, if you enable the PSD APD unit, Power Down Mode is automatically enabled. The device will enter Power Down Mode if the address strobe (ALE/AS) remains inactive for fifteen CLKIN (pin PD1) clock periods. The following should be kept in mind when the PSD is in Power Down Mode: • If the address strobe starts pulsing again, the PSD will return to normal operation. • • • • The PSD will also return to normal operation if either the CSI input returns low or the Reset input returns high. The MCU address/data bus is blocked from all memories and PLDs. Various signals can be blocked (prior to Power Down Mode) from entering the PLDs by setting the appropriate bits in the PMMR registers. The blocked signals include MCU control signals and the common clock (CLKIN). Note that blocking CLKIN from the PLDs will not block CLKIN from the APD unit. All PSD memories enter Standby Mode and are drawing standby current. However, the PLDs and I/O ports do not go into Standby Mode because you don’t want to have to wait for the logic and I/O to “wake-up” before their outputs can change. See Table 24 for Power Down Mode effects on PSD ports. Typical standby current is 50 µA for 5 V parts. This standby current value assumes that there are no transitions on any PLD input. Table 24. Power Down Mode’s Effect on Ports Port Function Pin Level MCU I/O PLD Out Address Out Data Port Peripheral I/O No Change No Change Undefined Three-State Three-State Table 25. PSD4000 Timing and Standby Current During Power Down Mode Mode Power Down PLD Propagation Delay Memory Access Time Access Recovery Time to Normal Access 5V VCC, Typical Standby Current Normal tpd (Note 1) No Access tLVDV 50 µA (Note 2) NOTES: 1. Power Down does not affect the operation of the PLD. The PLD operation in this mode is based only on the Turbo Bit. 2. Typical current consumption assuming no PLD inputs are changing state and the PLD Turbo bit is off. 56 Preliminary Information The PSD4000 Functional Blocks PSD4000 Series Figure 24. APD Logic Block APD EN PMMR0 BIT 1=1 (cont.) TRANSITION DETECTION DISABLE BUS INTERFACE ALE PD CLR RESET CSI SECONDARY FLASH SELECT APD COUNTER EDGE DETECT MAIN FLASH SELECT PD PLD SRAM SELECT CLKIN POWER DOWN (PDN) SELECT DISABLE MAIN AND SECONDARY FLASH/SRAM Figure 25. Enable Power Down Flow Chart RESET Enable APD Set PMMR0 Bit 1 = 1 OPTIONAL Disable desired inputs to PLD by setting PMMR0 bit 4 and PMMR2 bits 0. No ALE/AS idle for 15 CLKIN clocks? Yes PSD in Power Down Mode 57 PSD4000 Series The PSD4000 Functional Blocks (cont.) Preliminary Information Table 26. Power Management Mode Registers (PMMR0, PMMR2)** PMMR0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 * * * PLD Array clk PLD Turbo * APD Enable * 1 = off 1 = off 1 = on ***Bits 0, 2, 6, and 7 are not used, and should be set to 0, bit 5 should be set to 1. ***The PMMR0, and PMMR2 register bits are cleared to zero following power up. ***Subsequent reset pulses will not clear the registers. Bit 1 0 1 Bit 3 0 1 Bit 4 0 = = = = = Automatic Power Down (APD) is disabled. Automatic Power Down (APD) is enabled. PLD Turbo is on. PLD Turbo is off, saving power. CLKIN input to the PLD AND array is connected. Every CLKIN change will power up the PLD when Turbo bit is off. 1 = CLKIN input to PLD AND array is disconnected, saving power. PMMR2 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 * PLD array WRH/DBE PLD array ALE PLD** array CNTL2 PLD** array CNTL1 PLD** array CNTL0 * PLD array Addr. 1 = off 1 = off 1 = off 1 = off 1 = off 1 = off **Unused bits should be set to 0. **Refer to Table 14 the signals that are blocked on pins CNTL0-2. Bit 0 0 = Address A[7:0] inputs to the PLD AND array are connected. 1 = Address A[7:0] inputs to the PLD AND array are disconnected, saving power. Note: In 80C51XA mode, A[7:1] comes from Port F (PF1-PF3) and AD10 [3:0]. Bit 2 0 = Cntl0 input to the PLD AND array is connected. 1 = Cntl0 input to PLD AND array is disconnected, saving power. Bit 3 0 = Cntl1 input to the PLD AND array is connected. 1 = Cntl1 input to PLD AND array is disconnected, saving power. Bit 4 0 = Cntl2 input to the PLD AND array is connected. 1 = Cntl2 input to PLD AND array is disconnected, saving power. Bit 5 0 = ALE input to the PLD AND array is connected. 1 = ALE input to PLD AND array is disconnected, saving power. Bit 6 0 = WRH/DBE input to the PLD AND array is connected. 1 = WRH/DBE input to PLD AND array is disconnected, saving power. 58 Preliminary Information The PSD4000 Functional Blocks (cont.) PSD4000 Series Table 27. APD Counter Operation APD Enable Bit ALE PD Polarity ALE Level APD Counter 0 1 1 1 X X 1 0 X Pulsing 1 0 Not Counting Not Counting Counting (Generates PDN after 15 Clocks) Counting (Generates PDN after 15 Clocks) 9.5.2 Other Power Saving Options The PSD4000 offers other reduced power saving options that are independent of the Power Down Mode. Except for the SRAM Standby and CSI input features, they are enabled by setting bits in the PMMR0 and PMMR2 registers. 9.5.2.1 Zero Power PLD The power and speed of the PLDs are controlled by the Turbo bit (bit 3) in the PMMR0. By setting the bit to “1”, the Turbo mode is disabled and the PLDs consume Zero Power current when the inputs are not switching for an extended time of 70 ns. The propagation delay time will be increased after the Turbo bit is set to “1” (turned off) when the inputs change at a composite frequency of less than 15 MHz. When the Turbo bit is set to a “0” (turned on), the PLDs run at full power and speed. The Turbo bit affects the PLD’s D.C. power, AC power, and propagation delay. Refer to AC/DC spec for PLD timings. Note: Blocking MCU control signals with PMMR2 bits can further reduce PLD AC power consumption. 9.5.2.2 SRAM Standby Mode (Battery Backup) The PSD4000 supports a battery backup operation that retains the contents of the SRAM in the event of a power loss. The SRAM has a Vstby pin (PE6) that can be connected to an external battery. When VCC becomes lower than Vstby then the PSD will automatically connect to Vstby as a power source to the SRAM. The SRAM Standby Current (Istby) is typically 0.5 µA. The SRAM data retention voltage is 2 V minimum. The battery-on indicator (Vbaton) can be routed to PE7. This signal indicates when the VCC has dropped below the Vstby voltage and that the SRAM is running on battery power. 9.5.2.3 The CSI Input Pin PD2 of Port D can be configured in PSDsoft as the CSI input. When low, the signal selects and enables the internal Flash, Boot Block, SRAM, and I/O for read or write operations involving the PSD4000. A high on the CSI pin will disable the Flash memory, Boot Block, and SRAM, and reduce the PSD power consumption. However, the PLD and I/O pins remain operational when CSI is high. Note: there may be a timing penalty when using the CSI pin depending on the speed grade of the PSD that you are using. See the timing parameter t SLQV in the AC/DC specs. 9.5.2.4 Input Clock The PSD4000 provides the option to turn off the CLKIN input to the PLD AND array to save AC power consumption. During Power Down Mode, or, if the CLKIN input is not being used as part of the PLD logic equation, the clock should be disabled to save AC power. The CLKIN will be disconnected from the PLD AND array by setting bit 4 to a “1” in PMMR0. 9.5.2.5 MCU Control Signals The PSD4000 provides the option to turn off the address input (A7-0) and input control signals (CNTL0-2, ALE, and WRH/DBE) to the PLD to save AC power consumption. These signals are inputs to the PLD AND array. During Power Down Mode, or, if any of them are not being used as part of the PLD logic equation, these control signals should be disabled to save AC power. They will be disconnected from the PLD AND array by setting bits 0, 2, 3, 4, 5, and 6 to a “1” in the PMMR2. 59 PSD4000 Series The PSD4000 Functional Blocks (cont.) Preliminary Information 9.5.3 Reset and Power On Requirement 9.5.3.1 Power On Reset Upon power up the PSD4000 requires a reset pulse of tNLNH-PO (minimum 1 ms) after VCC is steady. During this time period the device loads internal configurations, clears some of the registers and sets the Flash into operating mode. After the rising edge of reset, the PSD4000 remains in the reset state for an additional tOPR (maximum 120 ns) nanoseconds before the first memory access is allowed. The PSD4000 Flash memory is reset to the read array mode upon power up. The FSi and CSBOOTi select signals along with the write strobe signal must be in the false state during power-up reset for maximum security of the data contents and to remove the possibility of data being written on the first edge of a write strobe signal. Any Flash memory write cycle initiation is prevented automatically when VCC is below VLKO. 9.5.3.2 Warm Reset Once the device is up and running, the device can be reset with a much shorter pulse of tNLNH (minimum 150 ns). The same tOPR time is needed before the device is operational after warm reset. Figure 26 shows the timing of the power on and warm reset. Figure 26. Power On and Warm Reset Timing OPERATING LEVEL t NLNH t NLNH-A t NLNH–PO VCC RESET t OPR POWER ON RESET WARM RESET t OPR 9.5.3.3 I/O Pin, Register and PLD Status at Reset Table 28 shows the I/O pin, register and PLD status during power on reset, warm reset and power down mode. PLD outputs are always valid during warm reset, and they are valid in power on reset once the internal PSD configuration bits are loaded. This loading of PSD is completed typically long before the VCC ramps up to operating level. Once the PLD is active, the state of the outputs are determined by the equations specified in PSDsoft. 60 Preliminary Information The PSD4000 Functional Blocks (cont.) PSD4000 Series Table 28. Status During Power On Reset, Warm Reset and Power Down Mode Port Configuration Power On Reset Warm Reset Power Down Mode MCU I/O Input Mode Input Mode Unchanged PLD Output Valid after internal PSD configuration bits are loaded Valid Depend on inputs to PLD (address are blocked in PD mode) Address Out Tri-stated Tri-stated Not defined Data Port Tri-stated Tri-stated Tri-stated Register Power On Reset Warm Reset Power Down Mode PMMR0, 2 Cleared to “0” Unchanged Unchanged VM Register* Initialized based on the selection in PSDsoft Configuration Menu. Initialized based on Unchanged the selection in PSDsoft Configuration Menu. All other registers Cleared to “0” Cleared to “0” Unchanged *SR_cod bit in the VM Register are always cleared to zero on power on or warm reset. 9.5.3.4 Reset of Flash Erase and Programming Cycles An external reset on the RESET pin will also reset the internal Flash memory state machine. When the Flash is in programming or erase mode, the RESET pin will terminate the programming or erase operation and return the Flash back to read mode in tNLNH-A (minimum 25 µs) time. 9.6 Programming In-Circuit using the JTAG-ISP Interface The JTAG-ISP interface on the PSD4000 can be enabled on Port E (see Table 29). All memory (Flash and Flash Boot Block), PLD logic, and PSD configuration bits may be programmed through the JTAG-ISC interface. A blank part can be mounted on a printed circuit board and programmed using JTAG-ISP. The standard JTAG signals (IEEE 1149.1) are TMS, TCK, TDI, and TDO. Two additional signals, TSTAT and TERR, are optional JTAG extensions used to speed up program and erase operations. By default, on a blank PSD (as shipped from factory or after erasure), four pins on Port E are enabled for the basic JTAG signals TMS, TCK, TDI, and TDO. See Application Note 54 for more details on JTAG In-System-Programming. Table 29. JTAG Port Signals Port E Pin JTAG Signals Description PE0 PE1 PE2 PE3 PE4 PE5 TMS TCK TDI TDO TSTAT TERR Mode Select Clock Serial Data In Serial Data Out Status Error Flag 61 PSD4000 Series The PSD4000 Functional Blocks (cont.) Preliminary Information 9.6.1 Standard JTAG Signals The JTAG configuration bit (non-volatile) inside the PSD can be set by the user in the PSDsoft. Once this bit is set and programmed in the PSD, the JTAG pins are dedicated to JTAG at all times and is in compliance with IEEE 1149.1. After power up the standard JTAG signals (TDI, TDO TCK and TMS) are inputs, waiting for a serial command from an external JTAG controller device (such as FlashLink or Automated Test Equipment). When the enabling command is received from the external JTAG controller, TDO becomes an output and the JTAG channel is fully functional inside the PSD. The same command that enables the JTAG channel may optionally enable the two additional JTAG pins, TSTAT and TERR. The PSD4000 supports JTAG ISP commands, but not Boundary Scan. ST’s PSDsoft software tool and FlashLink JTAG programming cable implement these JTAG-ISP commands. 9.6.2 JTAG Extensions TSTAT and TERR are two JTAG extension signals enabled by a JTAG command received over the four standard JTAG pins (TMS, TCK, TDI, and TDO). They are used to speed programming and erase functions by indicating status on PSD pins instead of having to scan the status out serially using the standard JTAG channel. See Application Note 54. TERR will indicate if an error has occurred when erasing a sector or programming a byte in Flash memory. This signal will go low (active) when an error condition occurs, and stay low until a special JTAG command is executed or a chip reset pulse is received after an “ISC-DISABLE” command. TSTAT behaves the same as the Rdy/Bsy signal described in section 9.1.1.2. TSTAT will be high when the PSD4000 device is in read array mode (Flash memory and Boot Block contents can be read). TSTAT will be low when Flash memory programming or erase cycles are in progress, and also when data is being written to the Secondary Flash Block. TSTAT and TERR can be configured as open-drain type signals with a JTAG command. 9.6.3 Security and Flash Memories Protection When the security bit is set, the device cannot be read on a device programmer or through the JTAG Port. When using the JTAG Port, only a full chip erase command is allowed. All other program/erase/verify commands are blocked. Full chip erase returns the part to a non-secured blank state. The Security Bit can be set in PSDsoft. All Flash Memory and Boot sectors can individually be sector protected against erasures. The sector protect bits can be set in PSDsoft. 62 Preliminary Information 10.0 Absolute Maximum Ratings PSD4000 Series Symbol Min Max Unit – 65 + 125 °C 0 + 70 °C Industrial – 40 + 85 °C Voltage on any Pin With Respect to GND – 0.6 +7 V VPP Device Programmer Supply Voltage With Respect to GND – 0.6 + 14 V VCC Supply Voltage With Respect to GND – 0.6 +7 V TSTG Parameter Condition Storage Temperature Operating Temperature PLDCC Commercial >2000 ESD Protection V NOTE: Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not recommended. Exposure to Absolute Maximum Rating conditions for extended periods of time may affect device reliability. 11.0 Operating Range Range Temperature VCC Tolerance Commercial 0° C to +70°C + 5 V ± 10% –40° C to +85°C + 5 V ± 10% 0° C to +70°C 3.0 V to 3.6 V –40° C to +85°C 3.0 V to 3.6 V Industrial Commercial Industrial 12.0 Recommended Operating Conditions Symbol Parameter Condition Min Typ Max Unit VCC Supply Voltage All Speeds 4.5 5 5.5 V VCC Supply Voltage V-Versions All Speeds 3.0 3.6 V 63 PSD4000 Series AC/DC Parameters Preliminary Information The following tables describe the AD/DC parameters of the PSD4000 family: ❏ DC Electrical Specification ❏ AC Timing Specification • PLD Timing • – Combinatorial Timing Microcontroller Timing – Read Timing – Write Timing – Power Down and Reset Timing Following are issues concerning the parameters presented: ❏ In the DC specification the supply current is given for different modes of operation. Before calculating the total power consumption, determine the percentage of time that the PSD4000 is in each mode. Also, the supply power is considerably different if the Turbo bit is "OFF". ❏ The AC power component gives the PLD, Flash memory, and SRAM mA/MHz specification. Figures 27 and 27a show the PLD mA/MHz as a function of the number of Product Terms (PT) used. ❏ In the PLD timing parameters, add the required delay when Turbo bit is "OFF". Figure 27. PLD ICC /FrequencyConsumption (VCC = 5 V ± 10%) 110 90 O RB TU ) 0% VCC = 5V 100 10 N( O FF 70 O 60 O 50 ) ON BO TUR TU RB ICC – (mA) 80 (25% 40 30 F 20 BO OF PT 100% PT 25% UR T 10 0 0 5 10 15 20 HIGHEST COMPOSITE FREQUENCY AT PLD INPUTS (MHz) 64 25 Preliminary Information Figure 27a. PLD ICC /Frequency Consumption (PSD4135G2V Versions, VCC = 3 V) 60 (cont.) VCC = 3V TU 40 30 O FF ICC – (mA) ) 100% ON ( RBO 50 5%) ON (2 URBO TU RB O AC/DC Parameters PSD4000 Series 20 T 10 BO PT 100% PT 25% FF O R TU 0 0 5 10 15 20 25 HIGHEST COMPOSITE FREQUENCY AT PLD INPUTS (MHz) Example of PSD4000 Typical Power Calculation at VCC = 5.0 V Conditions Highest Composite PLD input frequency (Freq PLD) MCU ALE frequency (Freq ALE) % Flash Access % SRAM access % I/O access = = = = = 8 MHz 4 MHz 80% 15% 5% (no additional power above base) Operational Modes % Normal % Power Down Mode = = 10% 90% Number of product terms used (from fitter report) % of total product terms = = 45 PT 45/176 = 25.5% Turbo Mode = ON Calculation (typical numbers used) ICC total = Ipwrdown x %pwrdown + %normal x (ICC (ac) + ICC (dc)) = Ipwrdown x %pwrdown + % normal x (%flash x 2.5 mA/MHz x Freq ALE + %SRAM x 1.5 mA/MHz x Freq ALE + % PLD x 2 mA/MHz x Freq PLD + #PT x 400 µA/PT = 50 µA x 0.90 + 0.1 x (0.8 x 2.5 mA/MHz x 4 MHz + 0.15 x 1.5 mA/MHz x 4 MHz +2 mA/MHz x 8 MHz + 45 x 0.4 mA/PT) = 45 µA + 0.1 x (8 + 0.9 + 16 + 18 mA) = 45 µA + 0.1 x 42.9 = 45 µA + 4.29 mA = 4.34 mA This is the operating power with no Flash writes or erases. Calculation is based on IOUT = 0 mA. 65 PSD4000 Series AC/DC Parameters (cont.) Preliminary Information Example of Typical Power Calculation at VCC = 5.0 V in Turbo Off Mode Conditions Highest Composite PLD input frequency (Freq PLD) = 8 MHz MCU ALE frequency (Freq ALE) = 4 MHz % Flash Access % SRAM access % I/O access = = = 80% 15% 5% (no additional power above base) Operational Modes % Normal % Power Down Mode = = 10% 90% Number of product terms used (from fitter report) % of total product terms = = 45 PT 45/176 = 25.5% Turbo Mode = Off Calculation (typical numbers used) ICC total = Ipwrdown x %pwrdown + %normal x (ICC (ac) + ICC (dc)) = Ipwrdown x %pwrdown + % normal x (%flash x 2.5 mA/MHz x Freq ALE + %SRAM x 1.5 mA/MHz x Freq ALE + % PLD x (from graph using Freq PLD)) = 50 µA x 0.90 + 0.1 x (0.8 x 2.5 mA/MHz x 4 MHz + 0.15 x 1.5 mA/MHz x 4 MHz + 24 mA) = 45 µA + 0.1 x (8 + 0.9 + 24) = 45 µA + 0.1 x 32.9 = 45 µA + 3.29 mA = 3.34 mA This is the operating power with no Flash writes or erases. Calculation is based on IOUT = 0 mA. 66 Preliminary Information PSD4000 Series PSD4000 DC Characteristics Symbol (5 V ± 10% Versions) Parameter Conditions Min Max Unit 5 5.5 V VCC Supply Voltage All Speeds VIH High Level Input Voltage 4.5 V < VCC < 5.5 V 2 VCC +.5 V VIL Low Level Input Voltage 4.5 V < VCC < 5.5 V –.5 0.8 V VIH1 Reset High Level Input Voltage (Note 1) .8 VCC VCC +.5 V VIL1 Reset Low Level Input Voltage (Note 1) –.5 .2 VCC –.1 V VHYS Reset Pin Hysteresis 0.3 VLKO VCC Min for Flash Erase and Program 2.5 VOL Output Low Voltage VOH Output High Voltage Except VSTBY On V 0.1 V IOL = 8 mA, VCC = 4.5 V 0.25 0.45 V IOH = –20 µA, VCC = 4.5 V 4.4 4.49 V IOH = –2 mA, VCC = 4.5 V 2.4 3.9 V VSBY SRAM Standby Voltage ISBY SRAM Standby Current (VSTBY Pin) VCC = 0 V IIDLE Idle Current (VSTBY Pin) VCC > VSBY VDF SRAM Data Retention Voltage Only on VSTBY ISB Standby Supply Current for Power Down Mode CSI > VCC –0.3 V (Notes 2, 3 and 5) ILI Input Leakage Current VSS < VIN < VCC ILO Output Leakage Current 0.45 < VIN < VCC IO Output Current Refer to IOL and IOH in the VOL and VOH row IOH1 = –1 µA VSBY – 0.8 V 2.0 0.5 –0.1 VCC V 1 µA 0.1 µA 2 V 100 200 µA –1 ±.1 1 µA –10 ±5 10 µA PLD_TURBO = OFF, f = 0 MHz (Note 3) 0 PLD_TURBO = ON, f = 0 MHz 400 700 µA/PT During Flash Write/Erase Only 15 30 mA Read Only, f = 0 MHz 0 0 mA f = 0 MHz 0 0 mA FLASH AC Adder 2.5 3.5 mA/MHz SRAM AC Adder 1.5 3.0 mA/MHz PLD Only Operating Supply Current Flash SRAM PLD AC Base NOTE: 1. 2. 3. 4. 5. 4.2 0.01 Output High Voltage VSTBY On ICC (AC) (Note 5) V IOL = 20 µA, VCC = 4.5 V VOH1 ICC (DC) (Note 5) 4.5 Typ mA Fig. 27 (Note 4) Reset input has hysteresis. VIL1 is valid at or below .2VCC –.1. VIH1 is valid at or above .8VCC. CSI deselected or internal Power Down mode is active. PLD is in non-turbo mode and none of the inputs are switching Refer to Figure 32 for PLD current calculation. I O = 0 mA 67 PSD4000 Series Microcontroller Interface – AC/DC Parameters (5V ± 10% Versions) Preliminary Information AC Symbols for PLD Timing. Example: t AVLX – Time from Address Valid to ALE Invalid. Signal Letters A C D E I L N P R S T W B M – – – – – – – – – – – – – – Address Input CEout Output Input Data E Input Interrupt Input ALE Input Reset Input or Output Port Signal Output UDS, LDS, DS, RD, PSEN Inputs Chip Select Input R/W Input WR Input Vstby Output Output Micro⇔Cell Signal Behavior t L H V X Z PW 68 – – – – – – – Time Logic Level Low or ALE Logic Level High Valid No Longer a Valid Logic Level Float Pulse Width Preliminary Information PSD4000 Series Microcontroller Interface – PSD4000 AC/DC Parameters (5V ± 10% Versions) Read Timing (5 V ± 10% Versions) -70 Symbol Parameter t LVLX ALE or AS Pulse Width t AVLX Address Setup Time t LXAX Conditions Min -90 Max Min Max Turbo Off Unit 15 20 ns (Note 3) 4 6 ns Address Hold Time (Note 3) 7 8 ns t AVQV Address Valid to Data Valid (Note 3) t SLQV CS Valid to Data Valid 70 90 Add 12** ns 75 100 ns RD to Data Valid (Note 5) 24 32 ns RD or PSEN to Data Valid, 80C51XA Mode (Note 2) 31 38 ns t RHQX RD Data Hold Time (Note 1) 0 0 ns t RLRH RD Pulse Width (Note 1) 27 32 ns t RHQZ RD to Data High-Z (Note 1) t EHEL E Pulse Width 27 32 ns t THEH R/W Setup Time to Enable 6 10 ns t ELTL R/W Hold Time After Enable 0 0 ns t AVPV Address Input Valid to Address Output Delay t RLQV NOTES: 1. 2. 3. 4. 5. (Note 4) 20 25 20 25 ns ns RD timing has the same timing as DS, LDS, UDS, and PSEN signals. RD and PSEN have the same timing. Any input used to select an internal PSD4000 function. In multiplexed mode, latched addresses generated from ADIO delay to address output on any Port. RD timing has the same timing as DS, LDS, and UDS signals. 69 PSD4000 Series Preliminary Information Microcontroller Interface – PSD4000 AC/DC Parameters (5V ± 10% Versions) Write Timing (5 V ± 10% Versions) -70 Symbol Parameter t LVLX ALE or AS Pulse Width t AVLX Address Setup Time t LXAX Address Hold Time t AVWL Address Valid to Leading Edge of WR t SLWL Conditions Min -90 Max Min Max Unit 15 20 (Note 1) 4 6 ns (Note 1) 7 8 ns (Notes 1 and 3) 8 15 ns CS Valid to Leading Edge of WR (Note 3) 12 15 ns t DVWH WR Data Setup Time (Note 3) 25 35 ns t WHDX WR Data Hold Time (Note 3) 4 5 ns t WLWH WR Pulse Width (Note 3) 28 35 ns t WHAX1 Trailing Edge of WR to Address Invalid (Note 3) 6 8 ns t WHAX2 Trailing Edge of WR to DPLD Address Input Invalid (Note 3 and 4) 0 0 ns t WHPV Trailing Edge of WR to Port Output Valid Using I/O Port Data Register (Note 3) 27 30 ns t AVPV Address Input Valid to Address Output Delay (Note 2) 20 25 ns NOTES: 1. 2. 3. 4. Any input used to select an internal PSD4000 function. In multiplexed mode, latched addresses generated from ADIO delay to address output on any Port. WR timing has the same timing as E, DS, LDS, UDS, WRL, and WRH signals. tWHAX2 is Address Hold Time for DPLD inputs that are used to generate chip selects for internal PSD memory. PLD Combinatorial Timing (5 V ± 10%) -70 Symbol Parameter Conditions Min -90 Max Min Max (Note 1) Unit Add 12 Sub 2 ns t PD PLD Input Pin/Feedback to PLD Combinatorial Output 20 25 t ARD PLD Array Delay 11 16 NOTE: 1. Fast Slew Rate output available on Port C and F. 70 Slew Rate TURBO OFF ns Preliminary Information PSD4000 Series Microcontroller Interface – PSD4000 AC/DC Parameters (5V ± 10% Versions) Power Down Timing (5 V ± 10%) -70 Symbol t LVDV t CLWH Parameter Conditions Min ALE Access Time from Power Down Maximum Delay from APD Enable to Internal PDN Valid Signal -90 Max Min 80 Using CLKIN Input Max Unit 90 ns 15 * t CLCL (µs) (Note 1) µs NOTE: 1. t CLCL is the CLKIN clock period. Vstbyon Timing (5 V ± 10%) Symbol Parameter Conditions Min Typ Max Unit t BVBH Vstby Detection to Vstbyon Output High (Note 1) 20 µs t BXBL Vstby Off Detection to Vstbyon Output Low (Note 1) 20 µs NOTE: 1. Vstbyon is measured at VCC ramp rate of 2 ms. Reset Pin Timing (5 V ± 10%) Symbol Parameter Conditions Min Typ Max 150 Unit t NLNH Warm RESET Active Low Time (Note 1) ns t OPR RESET High to Operational Device t NLNH-PO Power On Reset Active Low Time 1 ms t NLNH-A Warm RESET Active Low Time (Note 2) 25 µs 120 ns NOTE: 1. RESET will not abort Flash programming/erase cycles. 2. RESET will abort Flash programming or erase cycle. 71 PSD4000 Series Preliminary Information Microcontroller Interface – PSD4000 AC/DC Parameters (5V ± 10% Versions) Flash Program, Write and Erase Times (5 V ± 10%) Symbol Parameter Min Typ Flash Program 3 Flash Bulk Erase 10 t WHQV3 Sector Erase (Preprogrammed to 00) 1 t WHQV2 Sector Erase 2.2 t WHQV1 Word Program 14 Program/Erase Cycles (Per Sector) Sector Erase Time-Out t Q7VQV DQ7 Valid to Output Valid (Data Polling) (Notes 2 and 3) Unit 8.5 Flash Bulk Erase (Preprogrammed to 00) (Note 1) t WHWLO Max sec 30 sec sec 30 sec sec 1200 100,000 µs cycles 100 µs 30 ns NOTE: 1. Programmed to all zeros before erase. 2. The polling status DQ7 is valid tQ7VQV ns before the data DQ0-7 is valid for reading. 3. DQ7 is DQ15 for Motorola MCU with 16-bit data bus. ISC Timing (5 V ± 10%) -70 Symbol Parameter Min Max Min 20 Max Unit 18 MHz t ISCCF TCK Clock Frequency (except for PLD) (Note 1) t ISCCH TCK Clock High Time (Note 1) 23 26 ns t ISCCL TCK Clock Low Time (Note 1) 23 26 ns t ISCCF-P TCK Clock Frequency (for PLD only) (Note 2) t ISCCH-P TCK Clock High Time (for PLD only) (Note 2) 240 240 ns t ISCCL-P TCK Clock Low Time (for PLD only) (Note 2) 240 240 ns t ISCPSU ISC Port Set Up Time 6 8 ns t ISCPH ISC Port Hold Up Time 5 5 ns t ISCPCO ISC Port Clock to Output 21 23 ns t ISCPZV ISC Port High-Impedance to Valid Output 21 23 ns t ISCPVZ ISC Port Valid Output to High-Impedance 21 23 ns NOTES: 1. For “non-PLD” programming, erase or in ISC by-pass mode. 2. For program or erase PLD only. 72 Conditions -90 2 2 MHz Preliminary Information PSD4000 Series PSD4000 DC Characteristics Symbol (3.0 V to 3.6 V Versions) Parameter Advance Information Conditions Min Typ Max Unit 3.0 3.6 V VCC Supply Voltage All Speeds VIH High Level Input Voltage 3.0 V < VCC < 3.6 V .7 VCC VCC +.5 V VIL Low Level Input Voltage 3.0 V < VCC < 3.6 V –.5 0.8 V VIH1 Reset High Level Input Voltage (Note 1) .8 VCC VCC +.5 V VIL1 Reset Low Level Input Voltage (Note 1) –.5 .2 VCC –.1 V VHYS Reset Pin Hysteresis 0.3 VLKO VCC Min for Flash Erase and Program 1.5 VOL Output Low Voltage VOH Output High Voltage Except VSTBY On 0.1 V IOL = 4 mA, VCC = 3.0 V 0.15 0.45 V IOH = –20 µA, VCC = 3.0 V 2.9 2.99 V IOH = –1 mA, VCC = 3.0 V 2.7 2.8 V VSBY SRAM Standby Voltage ISBY SRAM Standby Current (VSTBY Pin) VCC = 0 V IIDLE Idle Current (VSTBY Pin) VCC > VSBY VDF SRAM Data Retention Voltage Only on VSTBY ISB Standby Supply Current for Power Down Mode CSI >VCC –0.3 V (Notes 2 and 3) ILI Input Leakage Current VSS < VIN < VCC ILO Output Leakage Current 0.45 < VIN < VCC IO Output Current Refer to IOL and IOH in the VOL and VOH row Operating Supply Current FLASH SRAM IOH1 = –1 µA VSBY – 0.8 NOTES: 1. 2. 3. 4. 5. V 2.0 0.5 –0.1 VCC V 1 µA 0.1 µA 2 V 50 100 µA –1 ±.1 1 µA –10 ±5 10 µA PLD_TURBO = OFF, f = 0 MHz (Note 3) 0 PLD_TURBO = ON, f = 0 MHz 200 400 µA/PT During FLASH Write/Erase Only 10 25 mA Read Only, f = 0 MHz 0 0 mA f = 0 MHz 0 0 mA PLD AC Base ICC (AC) (Note 5) V 0.01 Output High Voltage VSTBY On ICC (DC) (Note 5) 2.3 IOL = 20 µA, VCC = 3.0 V VOH1 PLD Only V mA (Note 4) Figure 27a FLASH AC Adder 1.5 2.0 mA/MHz SRAM AC Adder 0.8 1.5 mA/MHz Reset input has hysteresis. VIL1 is valid at or below .2VCC –.1. VIH1 is valid at or above .8VCC. CSI deselected or internal PD mode is active. PLD is in non-turbo mode and none of the inputs are switching. Refer to Figure 31a for PLD current calculation. I O = 0 mA. 73 PSD4000 Series Microcontroller Interface – PSD4000 AC/DC Parameters (3.0 V to 3.6 V Versions) Preliminary Information AC Symbols for PLD Timing. Example: t AVLX – Time from Address Valid to ALE Invalid. Signal Letters A C D E L N P Q R S T W B – – – – – – – – – – – – – Address Input CEout Output Input Data E Input ALE Input Reset Input or Output Port Signal Output Output Data WR, UDS, LDS, DS, IORD, PSEN Inputs Chip Select Input R/W Input Internal PDN Signal Vstby Output Signal Behavior t L H V X Z PW 74 – – – – – – – Time Logic Level Low or ALE Logic Level High Valid No Longer a Valid Logic Level Float Pulse Width Preliminary Information PSD4000 Series Microcontroller Interface – PSD4000 AC/DC Parameters (3.0 V to 3.6 V Versions) Read Timing (3.0 V to 3.6 V Versions) -90 Symbol Parameter t LVLX ALE or AS Pulse Width t AVLX Address Setup Time t LXAX Conditions Min -12 Max Min Max Turbo Off Unit 22 24 ns (Note 3) 7 9 ns Address Hold Time (Note 3) 8 10 ns t AVQV Address Valid to Data Valid (Note 3) t SLQV CS Valid to Data Valid 90 120 Add 20** ns 90 120 ns RD to Data Valid (Note 5) 35 35 ns RD or PSEN to Data Valid, 80C51XA Mode (Note 2) 45 48 ns t RHQX RD Data Hold Time (Note 1) 0 0 ns t RLRH RD Pulse Width (Note 1) 36 40 ns t RHQZ RD to Data High-Z (Note 1) t EHEL E Pulse Width 38 42 ns t THEH R/W Setup Time to Enable 10 16 ns t ELTL R/W Hold Time After Enable 0 0 ns t AVPV Address Input Valid to Address Output Delay t RLQV NOTES: 1. 2. 3. 4. 5. (Note 4) 38 40 30 35 ns ns RD timing has the same timing as DS, LDS, UDS, and PSEN signals. RD and PSEN have the same timing for 80C51XA. Any input used to select an internal PSD4135G2V function. In multiplexed mode latched address generated from ADIO delay to address output on any Port. RD timing has the same timing as DS, LDS, and UDS signals. 75 PSD4000 Series Preliminary Information Microcontroller Interface – PSD4000 AC/DC Parameters (3.0 V to 3.6 V Versions) Write Timing (3.0 V to 3.6 V Versions) -90 Symbol Parameter t LVLX ALE or AS Pulse Width t AVLX Address Setup Time t LXAX Address Hold Time t AVWL Address Valid to Leading Edge of WR t SLWL Conditions Min -12 Max Min Max Unit 22 24 (Note 1) 7 9 ns (Note 1) 8 10 ns (Notes 1 and 3) 15 18 ns CS Valid to Leading Edge of WR (Note 3) 15 18 ns t DVWH WR Data Setup Time (Note 3) 40 45 ns t WHDX WR Data Hold Time (Note 3) 5 8 ns t WLWH WR Pulse Width (Note 3) 40 45 ns t WHAX1 Trailing Edge of WR to Address Invalid (Note 3) 8 10 ns t WHAX2 Trailing Edge of WR to DPLD Address Input Invalid (Notes 3 and 4) 0 0 ns t WHPV Trailing Edge of WR to Port Output Valid Using I/O Port Data Register (Note 3) 33 33 ns t AVPV Address Input Valid to Address Output Delay (Note 2) 30 35 ns NOTES: 1. 2. 3. 4. Any input used to select an internal PSD4000 function. In multiplexed mode, latched addresses generated from ADIO delay to address output on any Port. WR timing has the same timing as E, DS, LDS, UDS, WRL, and WRH signals. tWHAX2 is Address hold time for DPLD inputs that are used to generate chip selects for internal PSD memory. PLD Combinatorial Timing (3.0 V to 3.6 V Versions) -90 Symbol Parameter Conditions Min -12 Max Min Max (Note 1) Unit Add 20 Sub 6 ns t PD PLD Input Pin/Feedback to PLD Combinatorial Output 38 43 t ARD PLD Array Delay 23 27 NOTE: 1. Fast Slew Rate output available on Port C and F. 76 Slew Rate TURBO OFF ns Preliminary Information PSD4000 Series Microcontroller Interface – PSD4000 AC/DC Parameters (3.0 V to 3.6 V Versions) Power Down Timing (3.0 V to 3.6 V Versions) -90 Symbol Parameter t LVDV ALE Access Time from Power Down t CLWH Maximum Delay from APD Enable to Internal PDN Valid Signal Conditions Min -12 Max Min 128 Using CLKIN Input Max Unit 135 ns 15 * t CLCL (µs) (Note 1) µs NOTE: 1. tCLCL is the CLKIN clock period. Vstbyon Timing (3.0 V to 3.6 V Versions) Symbol Parameter Conditions Min Typ Max Unit t BVBH Vstby Detection to Vstbyon Output High (Note 1) 20 µs t BXBL Vstby Off Detection to Vstbyon Output Low (Note 1) 20 µs NOTE: 1. Vstbyon is measured at VCC ramp rate of 2 ms. Reset Pin Timing (3.0 V to 3.6 V Versions) Symbol Parameter Conditions Min Typ Max 300 Unit t NLNH Warm RESET Active Low Time (Note 1) ns t OPR RESET High to Operational Device t NLNH-PO Power On Reset Active Low Time 1 ms t NLNH-A Warm RESETActive Low Time (Note 2) 25 µs 300 ns NOTE: 1. RESET will not abort Flash programming/erase cycles. 2. RESET will abort Flash programming or erase cycle. 77 PSD4000 Series Preliminary Information Microcontroller Interface – PSD4000 AC/DC Parameters (3.0 V to 3.6 V Versions) Flash Program, Write and Erase Times (3.0 V to 3.6 V Versions) Symbol Parameter Min Typ Flash Program 3 Flash Bulk Erase 10 t WHQV3 Sector Erase (Preprogrammed to 00) 1 t WHQV2 Sector Erase 2.2 t WHQV1 Word Program 14 Program/Erase Cycles (Per Sector) Sector Erase Time-Out t Q7VQV DQ7 Valid to Output Valid (Data Polling) (Notes 2 and 3) Unit 8.5 Flash Bulk Erase (Preprogrammed to 00) (Note 1) t WHWLO Max sec 30 sec sec 30 sec sec 1200 100,000 µs cycles 100 µs 30 ns NOTES: 1. Programmed to all zeros before erase. 2. The polling status DQ7 is valid tQ7VQV ns before the data DQ0-7 is valid for reading. 3. DQ7 is DQ15 for Motorola MCU with 16-bit data bus. ISC Timing (3.0 V to 3.6 V Versions) -90 Symbol Parameter Conditions Min -12 Max Min Unit 12 MHz t ISCCF TCK Clock Frequency (except for PLD) (Note 1) t ISCCH TCK Clock High Time (Note 1) 30 40 ns t ISCCL TCK Clock Low Time (Note 1) 30 40 ns t ISCCF-P TCK Clock Frequency (for PLD only) (Note 2) t ISCCH-P TCK Clock High Time (for PLD only) (Note 2) 240 240 ns t ISCCL-P TCK Clock Low Time (for PLD only) (Note 2) 240 240 ns t ISCPSU ISC Port Set Up Time 11 12 ns t ISCPH ISC Port Hold Up Time 5 5 ns t ISCPCO ISC Port Clock to Output 26 32 ns t ISCPZV ISC Port High-Impedance to Valid Output 26 32 ns t ISCPVZ ISC Port Valid Output to High-Impedance 26 32 ns NOTES: 1. For “non-PLD” programming, erase or in ISC by-pass mode. 2. For program or erase PLD only. 78 15 Max 2 2 MHz Preliminary Information PSD4000 Series Figure 28. Read Timing tAVLX tLXAX * ALE/AS tLVLX A/D MULTIPLEXED BUS ADDRESS VALID DATA VALID tAVQV ADDRESS NON-MULTIPLEXED BUS ADDRESS VALID DATA NON-MULTIPLEXED BUS DATA VALID tSLQV CSI tRLQV tRHQX tRLRH RD (PSEN, DS) tRHQZ tEHEL E tTHEH tELTL R/W tAVPV ADDRESS OUT *tAVLX and tLXAX are not required 80C51XA in Burst Mode. 79 PSD4000 Series Preliminary Information Figure 29. Write Timing tAVLX t LXAX ALE/AS t LVLX A/D MULTIPLEXED BUS DATA VALID ADDRESS VALID tAVWL ADDRESS NON-MULTIPLEXED BUS ADDRESS VALID DATA NON-MULTIPLEXED BUS DATA VALID tSLWL CSI tDVWH t WLWH WR (DS) t WHDX t WHAX t EHEL E t THEH t ELTL R/ W t WLMV tAVPV t WHPV ADDRESS OUT 80 STANDARD MCU I/O OUT Preliminary Information PSD4000 Series Figure 30. Combinatorial Timing – PLD GPLD INPUT t PD GPLD OUTPUT Figure 31. JTAG-ISP Timing t ISCCH TCK t ISCCL t ISCPSU t ISCPH TDI/TMS t ISCPZV t ISCPCO ISC OUTPUTS/TDO t ISCPVZ ISC OUTPUTS/TDO 81 PSD4000 Series Preliminary Information Figure 32. Reset Timing OPERATING LEVEL t NLNH t NLNH-A t NLNH– PO VCC RESET t OPR POWER ON RESET WARM RESET t OPR Figure 33. Key to Switching Waveforms WAVEFORMS 82 INPUTS OUTPUTS STEADY INPUT STEADY OUTPUT MAY CHANGE FROM HI TO LO WILL BE CHANGING FROM HI TO LO MAY CHANGE FROM LO TO HI WILL BE CHANGING LO TO HI DON'T CARE CHANGING, STATE UNKNOWN OUTPUTS ONLY CENTER LINE IS TRI-STATE Preliminary Information 14.0 Pin Capacitance PSD4000 Series TA = 25 °C, f = 1 MHz Parameter 1 Symbol Conditions Typical 2 Max Unit CIN Capacitance (for input pins only) VIN = 0 V 4 6 pF COUT Capacitance (for input/output pins) VOUT = 0 V 8 12 pF CVPP Capacitance (for CNTL2/VPP) VPP = 0 V 18 25 pF NOTES: 1. These parameters are only sampled and are not 100% tested. 2. Typical values are for TA = 25°C and nominal supply voltages. 15.0 Figure 34. AC Testing Input/Output Waveform 3.0V TEST POINT 1.5V 0V 16.0 Figure 35. AC Testing Load Circuit 2.01 V 195 Ω DEVICE UNDER TEST 17.0 Programming CL = 30 pF (INCLUDING SCOPE AND JIG CAPACITANCE) Upon delivery from ST, the PSD4000 device has all bits in the PLDs and memories in the “1” or high state. The configuration bits are in the “0” or low state. The code, configuration, and PLDs logic are loaded through the procedure of programming. Information for programming the device is available directly from ST. Please contact your local sales representative. (See the last page.) 83 PSD4000 Series 18.0 PSD4000 Pin Assignments 84 Preliminary Information 80-Pin Plastic Thin Quad Flatpack (TQFP) (Package Type U) Pin No. Pin Assignments Pin No. Pin Assignments 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 PD2 PD3 AD0 AD1 AD2 AD3 AD4 GND VCC AD5 AD6 AD7 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 PG0 PG1 PG2 PG3 PG4 PG5 PG6 PG7 VCC GND PF0 PF1 PF2 PF3 PF4 PF5 PF6 PF7 RESET CNTL2 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 GND GND PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 CNTL0 CNTL1 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 VCC GND PE0 PE1 PE2 PE3 PE4 PE5 PE6 PE7 PD0 PD1 Preliminary Information 61 PB0 62 PB1 63 PB2 64 PB3 65 PB4 66 PB5 67 PB6 69 VCC 68 PB7 70 GND 71 PE0 72 PE1 73 PE2 74 PE3 75 PE4 76 PE5 77 PE6 78 PE7 79 PD0 80 PD1 Figure 36. Drawing U5 – 80-Pin Plastic Thin Quad Flatpack (TQFP) (Package Type U) 11 50 GND AD7 12 49 GND AD8 13 48 PC7 AD9 14 47 PC6 AD10 15 46 PC5 AD11 16 45 PC4 AD12 17 44 PC3 AD13 18 43 PC2 AD14 19 42 PC1 AD15 20 41 PC0 CNTL2 40 51 PA0 AD6 RESET 39 10 PF7 38 52 PA1 AD5 PF6 37 9 PF5 36 53 PA2 VCC PF4 35 54 PA3 GND 8 PF3 34 7 PF2 33 55 PA4 AD4 PF1 32 6 PF0 31 56 PA5 AD3 GND 30 5 VCC 29 57 PA6 AD2 PG7 28 4 PG6 27 58 PA7 AD1 PG5 26 3 PG4 25 59 CNTL0 AD0 PG3 24 60 CNTL1 2 PG2 23 1 PD3 PG1 22 PD2 PG0 21 19.0 PSD4000 Package Information PSD4000 Series 85 PSD4000 Series Preliminary Information Figure 36A. Drawing U5 – 80-Pin Plastic Thin Quad Flatpack (TQFP) (Package Type U) D D1 D3 80 1 2 3 Index Mark E3 E1 E Standoff: 0.05 mm Min. A1 A2 C A α L B Load Coplanarity: 0.102 mm Max. e1 Family: Plastic Thin Quad Flatpack (TQFP) Millimeters Symbol Min Max α 0° A Inches Min Max 7° 0° 8° – 1.20 – 0.047 A2 0.95 1.05 0.037 0.041 B 0.17 0.27 0.007 0.011 C Notes Reference 0.20 0.008 D 13.95 14.05 0.512 0.551 D1 11.95 12.05 0.433 0.472 D3 9.5 Notes Reference 0.374 Reference E 13.95 14.05 0.512 0.551 E1 11.95 12.05 0.433 0.472 E3 9.5 Reference 0.374 Reference e1 0.50 Reference 0.019 Reference L N 0.45 0.75 80 0.018 0.030 80 060198R0 86 Preliminary Information 20.0 Selector Guide Selector Guide – PSD4000 Series Part # 5 Volts MCU PLDs/Decoders I/O Data Path Inputs Input Macrocells Output Macrocells Outputs Page Reg. Memory Other Software Ports Flash Program Store ISP via JTAG 2nd Flash Array IAP via MCU EEPROM Zero Power SRAM Per. Mode w/BB Security PSDsoft Express PSDsoft 2000 PMU APD PSD4135G2 16 57 – – 24 8-bit 52 4096Kb 256Kb – 64Kb X X X – X X X X PSD4235G2 16 57 24 16 24 8-bit 52 4096Kb 256Kb – 64Kb X X X – X X X X X PSD4000 Series 87 PSD4000 Series 21.0 Part Number Construction Preliminary Information Flash PSD Part Number Construction CHARACTER # 1 PART NUMBER 2 I 3 I P 4 I S 5 I D 6 7 8 9 10 11 12 13 14 15 16 17 18 19 I I I I I I I I I I I I I I 42 1 3 F 2 – A – 1 5 J TEMP RANGE "Blank" = 0°C to +70°C (Commercial) I = –40°C to +85°C (Industrial) PSD BRAND NAME PSD = Standard Low Power Device FAMILY/SERIES 8 = Flash PSD for 8-bit MCUs PACKAGE TYPE J = PLCC U = TQFP M = PQFP B81 = BGA 9 = Flash PSD for 8-bit MUCs (with simple PLD) 41 = Flash PSD for 16-bit MUCs (with simple PLD) 42 = Flash PSD for 16-bit MUCs (with CPLD) SRAM SIZE 0 = 0Kb 1 = 16Kb 2 = 32Kb 3 = 64Kb NVM SIZE 1 = 256Kb 2 = 512Kb 3 = 1Mb 4 = 2Mb 5 = 4Mb SPEED - 70 = 70ns - 90 = 90ns - 12 = 120ns - 15 = 150ns - 20 = 200ns REVISION "Blank" = no rev. - A = Rev. A - B = Rev. B - C = Rev. C Vc c VOLTAGE I/O COUNT & OTHER F = 27 I/O G = 52 I/O 2ND NVM TYPE, SIZE & CONFIGURATION 1 = EEPROM, 256Kb 2 = FLASH, 256Kb 3 = No 2nd Array 22.0 Ordering Information 88 "blank" = 5 Volt V = 3.0 Volt PSD4135G2 REVISION HISTORY Table 1. Document Revision History Date Rev. 01-May-2000 1.0 31-Jan-2002 1.1 2/3 Description of Revision PSD4135G2: Document written in the WSI format. Initial release PSD4135G2: Flash In-System-Programmable Peripherals for 16-Bit MCUs Front page, and back two pages, in ST format, added to the PDF file Any references to Waferscale, WSI, EasyFLASH and PSDsoft 2000 updated to ST, ST, Flash+PSD and PSDsoft Express PSD4135G2 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is registered trademark of STMicroelectronics All other names are the property of their respective owners © 2002 STMicroelectronics - All Rights Reserved STMicroelectronics group of companies Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. www.st.com 3/3