STMICROELECTRONICS PSD953F2V-15MT

PSD813F2V PSD854F2V
Flash in-system programmable (ISP) peripherals
for 8-bit MCUs, 3.3 V
NOT FOR NEW DESIGN
FEATURES SUMMARY
■
■
■
■
■
■
■
FLASH IN-SYSTEM PROGRAMMABLE (ISP)
PERIPHERAL FOR 8-BIT MCUS
DUAL BANK FLASH MEMORIES
– UP TO 2 Mbit OF PRIMARY FLASH
MEMORY (8 Uniform Sectors, 32K x8)
– UP TO 256 Kbit SECONDARY FLASH
MEMORY (4 Uniform Sectors)
– Concurrent operation: READ from one
memory while erasing and writing the
other
UP TO 256 Kbit of SRAM
27 RECONFIGURABLE I/O PORTS
ENHANCED JTAG SERIAL PORT
PLD WITH MACROCELLS
– Over 3000 Gates of PLD: CPLD and
DPLD
– CPLD with 16 Output Macrocells (OMCs)
and 24 Input Macrocells (IMCs)
– DPLD - user defined internal chip select
decoding
27 INDIVIDUALLY CONFIGURABLE I/O
PORT PINS
The can be used for the following functions:
– MCU I/Os
– PLD I/Os
– Latched MCU address output
– Special function I/Os.
– 16 of the I/O ports may be configured as
open-drain outputs.
IN-SYSTEM PROGRAMMING (ISP) WITH
JTAG
– Built-in JTAG compliant serial port allows
full-chip In-System Programmability
– Efficient manufacturing allow easy
product testing and programming
– Use low cost FlashLINK cable with PC
PAGE REGISTER
– Internal page register that can be used to
expand the microcontroller address space
by a factor of 256
PROGRAMMABLE POWER MANAGEMENT
)
s
(
ct
Figure 1. Packages
PQFP52 (M)
c
u
d
e
t
le
so
s
b
O
■
■
r
P
e
t
e
l
o
May 2009
o
r
P
PLCC52 (J)
b
O
-
u
d
o
■
)
s
t(
TQFP64 (U)
■
■
■
■
HIGH ENDURANCE:
– 100,000 Erase/WRITE Cycles of Flash
Memory
– 1,000 Erase/WRITE Cycles of PLD
– 15 Year Data Retention
3.3V±10% SINGLE SUPPLY VOLTAGE
STANDBY CURRENT AS LOW AS 25µA
Packages are ECOPACK®
Doc ID 10552 Rev 3
This is information on a product still in production but not recommended for new designs.
1/109
PSD813F2V, PSD854F2V
TABLE OF CONTENTS
FEATURES SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SUMMARY DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PIN DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PSD ARCHITECTURAL OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Page Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PLDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
I/O Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
MCU Bus Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
JTAG Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
In-System Programming (ISP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Power Management Unit (PMU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
c
u
d
)
s
t(
DEVELOPMENT SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
o
r
P
PSD Register Description and Address Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
e
t
le
DETAILED OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Memory Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Primary Flash Memory and Secondary Flash memory Description . . . . . . . . . . . . . . . . . . . . . 20
Memory Block Select Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Ready/Busy (PC3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Memory Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
)
s
(
ct
o
s
b
O
-
INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Power-up Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
READ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Read Memory Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Read Primary Flash Identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Read Memory Sector Protection Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Reading the Erase/Program Status Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Data Polling Flag (DQ7). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Toggle Flag (DQ6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Error Flag (DQ5). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Erase Time-out Flag (DQ3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
u
d
o
r
P
e
t
e
l
o
s
b
O
PROGRAMMING FLASH MEMORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Data Polling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Data Toggle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Unlock Bypass (PSD833F2x, PSD834F2x, PSD853F2x, PSD854F2x) . . . . . . . . . . . . . . . . . . . . 26
ERASING FLASH MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2/109
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
Flash Bulk Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Flash Sector Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Suspend Sector Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Resume Sector Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SPECIFIC FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Flash Memory Sector Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Reset Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Reset (RESET) Signal (on the PSD83xF2 and PSD85xF2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
SRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
SECTOR SELECT AND SRAM SELECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Memory Select Configuration for MCUs with Separate Program and Data Spaces . . . . . . . . 30
Configuration Modes for MCUs with Separate Program and Data Spaces . . . . . . . . . . . . . . . 30
Separate Space Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Combined Space Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
c
u
d
)
s
t(
o
r
P
PAGE REGISTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
PLDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
e
t
le
The Turbo Bit in PSD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Decode PLD (DPLD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Complex PLD (CPLD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Output Macrocell (OMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Product Term Allocator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Loading and Reading the Output Macrocells (OMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
The OMC Mask Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
The Output Enable of the OMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Input Macrocells (IMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
)
s
(
ct
o
s
b
O
-
u
d
o
r
P
e
MCU BUS INTERFACE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
PSD Interface to a Multiplexed 8-Bit Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
PSD Interface to a Non-Multiplexed 8-Bit Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Data Byte Enable Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
MCU Bus Interface Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
80C31 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
80C251 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
80C51XA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
68HC11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
t
e
l
o
s
b
O
I/O PORTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
General Port Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Port Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
MCU I/O Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Doc ID 10552 Rev 3
3/109
PSD813F2V, PSD854F2V
PLD I/O Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Address Out Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Address In Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Data Port Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Peripheral I/O Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
JTAG In-System Programming (ISP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Port Configuration Registers (PCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Direction Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Drive Select Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Port Data Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Data In. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Data Out Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Output Macrocells (OMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
OMC Mask Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Input Macrocells (IMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Enable Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Ports A and B – Functionality and Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Port C – Functionality and Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Port D – Functionality and Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
External Chip Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
c
u
d
e
t
le
)
s
t(
o
r
P
POWER MANAGEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
o
s
b
O
-
Automatic Power-down (APD) Unit and Power-down Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Power-down Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
For Users of the HC11 (or compatible) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Other Power Saving Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
PLD Power Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
PSD Chip Select Input (CSI, PD2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Input Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Input Control Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
)
s
(
ct
u
d
o
r
P
e
RESET TIMING AND DEVICE STATUS AT RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Power-Up Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Warm Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
I/O Pin, Register and PLD Status at Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Reset of Flash Memory Erase and Program Cycles (on the PSD834Fx) . . . . . . . . . . . . . . . . . 67
t
e
l
o
s
b
O
PROGRAMMING IN-CIRCUIT USING THE JTAG SERIAL INTERFACE . . . . . . . . . . . . . . . . . . . . . . 69
Standard JTAG Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
JTAG Extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Security and Flash memory Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
INITIAL DELIVERY STATE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
AC/DC PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
4/109
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
MAXIMUM RATING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
DC AND AC PARAMETERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
PACKAGE MECHANICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
PART NUMBERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
APPENDIX A.PQFP52 PIN ASSIGNMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
APPENDIX B.PLCC52 PIN ASSIGNMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
APPENDIX C.TQFP64 PIN ASSIGNMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
REVISION HISTORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
c
u
d
e
t
le
)
s
(
ct
)
s
t(
o
r
P
o
s
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
5/109
PSD813F2V, PSD854F2V
SUMMARY DESCRIPTION
The PSD8XXFX family of memory systems for microcontrollers (MCUs) brings In-System-Programmability (ISP) to Flash memory and programmable
logic. The result is a simple and flexible solution for
embedded designs. PSD devices combine many
of the peripheral functions found in MCU based
applications.
Table 1 summarizes all the devices in the
PSD834F2, PSD853F2, PSD854F2.
The CPLD in the PSD devices features an optimized macrocell logic architecture. The PSD macrocell was created to address the unique
requirements of embedded system designs. It allows direct connection between the system address/data bus, and the internal PSD registers, to
simplify communication between the MCU and
other supporting devices.
The PSD device includes a JTAG Serial Programming interface, to allow In-System Programming
(ISP) of the entire device. This feature reduces development time, simplifies the manufacturing flow,
and dramatically lowers the cost of field upgrades.
Using ST’s special Fast-JTAG programming, a design can be rapidly programmed into the PSD in as
little as seven seconds.
The innovative PSD8XXFX family solves key
problems faced by designers when managing discrete Flash memory devices, such as:
– First-time In-System Programming (ISP)
– Complex address decoding
– Simultaneous read and write to the device.
The JTAG Serial Interface block allows In-System
Programming (ISP), and eliminates the need for
an external Boot EPROM, or an external programmer. To simplify Flash memory updates, program
execution is performed from a secondary Flash
memory while the primary Flash memory is being
updated. This solution avoids the complicated
hardware and software overhead necessary to implement IAP.
ST makes available a software development tool,
PSDsoft Express, that generates ANSI-C compliant code for use with your target MCU. This code
allows you to manipulate the non-volatile memory
(NVM) within the PSD. Code examples are also
provided for:
– Flash memory IAP via the UART of the host
MCU
– Memory paging to execute code across
several PSD memory pages
– Loading, reading, and manipulation of PSD
macrocells by the MCU.
c
u
d
e
t
le
Table 1. Product Range
o
s
b
O
-
Primary Flash
Memory
(8 Sectors)
Secondary
Flash Memory
4 Sectors)
PSD813F2V
1 Mbit
256 Kbit
16 Kbit
PSD854F2V
2 Mbit
256 Kbit
256 Kbit
(1)
Part Number
r
P
e
u
d
o
)
s
(
ct
SRAM
)
s
t(
o
r
P
Input
Output
Serial
ISP
JTAG/
ISC Port
27
24
16
yes
yes
27
24
16
yes
yes
I/O Ports
Number of
Macrocells
Turbo
Mode
Note: 1. All products support: JTAG serial ISP, MCU parallel ISP, ISP Flash memory, ISP CPLD, Security features, Power Management
Unit (PMU), Automatic Power-down (APD).
t
e
l
o
s
b
O
6/109
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
40 CNTLO
41 RESET
42 CNTL2
43 CNTL1
44 PB7
45 PB6
46 GND
47 PB5
48 PB4
49 PB3
50 PB2
51 PB1
52 PB0
Figure 2. PQFP52 Connections
PC0 13
27 AD4
e
t
le
so
)
s
(
ct
AD3 26
28 AD5
AD2 25
29 AD6
PC1 12
AD1 24
30 AD7
PC2 11
AD0 23
31 VCC
PC3 10
PA0 22
32 AD8
GND 9
PA1 21
33 AD9
VCC 8
PA2 20
34 AD10
PC4 7
GND 19
35 AD11
PC5 6
PA3 18
36 AD12
PC6 5
PA4 17
37 AD13
PC7 4
PA5 16
38 AD14
PD0 3
PA6 15
39 AD15
PD1 2
PA7 14
PD2 1
c
u
d
)
s
t(
o
r
P
AI02858
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
7/109
PSD813F2V, PSD854F2V
PB7
CNTL1
CNTL2
RESET
CNTL0
PB5
PB6
PB4
GND
PB3
47
PB2
48
PB1
49
2
50
3
51
4
52
5
1
PD1
6
8
7
PD2
PB0
Figure 3. PLCC52 Connections
46
AD15
9
45
AD14
PD0
10
44
AD13
PC7
11
43
AD12
PC6
12
42
AD11
PC5
13
41
AD10
PC4
14
40
AD9
VCC
15
39
AD8
GND
16
38
VCC
PC3
17
37
PC2
18
36
PC1
19
35
PC0
20
P
e
let
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
31
32
33
AD2
AD3
AD0
PA0
PA1
PA2
u
d
o
AD1
30
29
28
27
26
o
s
b
O
GND
25
PA3
24
PA4
PA5
23
22
PA6
PA7
21
34
)
s
(
ct
8/109
ro
c
u
d
AD7
)
s
t(
AD6
AD5
AD4
AI02857
PSD813F2V, PSD854F2V
49 NC
50 RESET
51 CNTL2
52 CNTL1
53 PB7
54 PB6
55 GND
56 GND
57 PB5
58 PB4
59 PB3
60 PB2
61 PB1
62 PB0
63 NC
64 NC
Figure 4. TQFP64 Connections
PD2 1
48 CNTL0
PD1 2
47 AD15
PD0 3
46 AD14
PC7 4
45 AD13
PC6 5
44 AD12
PC5 6
43 AD11
PC4 7
42 AD10
VCC 8
41 AD9
VCC 9
40 AD8
GND 10
39 VCC
GND 11
38 VCC
PC3 12
37 AD7
PC2 13
36 AD6
PC1 14
35 AD5
ro
PC0 15
34 AD4
)
s
(
ct
33 AD3
AD2 32
ND 31
o
s
b
O
-
AD1 30
P
e
let
AD0 29
PA0 28
PA1 27
PA2 26
GND 25
GND 24
PA3 23
PA4 22
PA5 21
PA6 20
PA7 19
NC 18
16
NC 17
NC
c
u
d
)
s
t(
AI09645b
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
9/109
PSD813F2V, PSD854F2V
PIN DESCRIPTION
Table 2. Pin Description (for the PLCC52 package - Note 1)
Pin Name
Pin
Type
Description
This is the lower Address/Data port. Connect your MCU address or address/data bus
according to the following rules:
If your MCU has a multiplexed address/data bus where the data is multiplexed with the
lower address bits, connect AD0-AD7 to this port.
ADIO0-7
30-37
I/O
If your MCU does not have a multiplexed address/data bus, or you are using an 80C251
in page mode, connect A0-A7 to this port.
If you are using an 80C51XA in burst mode, connect A4/D0 through A11/D7 to this port.
ALE or AS latches the address. The PSD drives data out only if the READ signal is active
and one of the PSD functional blocks was selected. The addresses on this port are
passed to the PLDs.
This is the upper Address/Data port. Connect your MCU address or address/data bus
according to the following rules:
If your MCU has a multiplexed address/data bus where the data is multiplexed with the
lower address bits, connect A8-A15 to this port.
c
u
d
)
s
t(
If your MCU does not have a multiplexed address/data bus, connect A8-A15 to this port.
ADIO8-15
39-46
I/O
o
r
P
If you are using an 80C251 in page mode, connect AD8-AD15 to this port.
If you are using an 80C51XA in burst mode, connect A12/D8 through A19/D15 to this
port.
e
t
le
o
s
b
O
-
ALE or AS latches the address. The PSD drives data out only if the READ signal is active
and one of the PSD functional blocks was selected. The addresses on this port are
passed to the PLDs.
The following control signals can be connected to this port, based on your MCU:
WR – active Low Write Strobe input.
CNTL0
47
I
)
s
(
ct
R_W – active High READ/active Low write input.
This port is connected to the PLDs. Therefore, these signals can be used in decode and
other logic equations.
u
d
o
The following control signals can be connected to this port, based on your MCU:
RD – active Low Read Strobe input.
r
P
e
t
e
l
o
CNTL1
bs
50
E – E clock input.
DS – active Low Data Strobe input.
I
PSEN – connect PSEN to this port when it is being used as an active Low READ signal.
For example, when the 80C251 outputs more than 16 address bits, PSEN is actually the
READ signal.
O
This port is connected to the PLDs. Therefore, these signals can be used in decode and
other logic equations.
CNTL2
10/109
49
I
This port can be used to input the PSEN (Program Select Enable) signal from any MCU
that uses this signal for code exclusively. If your MCU does not output a Program Select
Enable signal, this port can be used as a generic input. This port is connected to the
PLDs.
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
Pin Name
Pin
Type
Description
Reset
48
I
Resets I/O Ports, PLD macrocells and some of the Configuration Registers. Must be Low
at Power-up.
These pins make up Port A. These port pins are configurable and can have the following
functions:
MCU I/O – write to or read from a standard output or input port.
CPLD macrocell (McellAB0-7) outputs.
Inputs to the PLDs.
29
28
27
25
24
23
22
21
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
Latched address outputs (see Table 6).
I/O
Address inputs. For example, PA0-3 could be used for A0-A3 when using an 80C51XA in
burst mode.
As the data bus inputs D0-D7 for non-multiplexed address/data bus MCUs.
D0/A16-D3/A19 in M37702M2 mode.
Peripheral I/O mode.
c
u
d
)
s
t(
Note: PA0-PA3 can only output CMOS signals with an option for high slew rate. However,
PA4-PA7 can be configured as CMOS or Open Drain Outputs.
7
6
5
4
3
2
52
51
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
o
r
P
These pins make up Port B. These port pins are configurable and can have the following
functions:
MCU I/O – write to or read from a standard output or input port.
e
t
le
CPLD macrocell (McellAB0-7 or McellBC0-7) outputs.
I/O
Inputs to the PLDs.
o
s
b
O
-
Latched address outputs (see Table 6).
Note: PB0-PB3 can only output CMOS signals with an option for high slew rate. However,
PB4-PB7 can be configured as CMOS or Open Drain Outputs.
)
s
(
ct
PC0 pin of Port C. This port pin can be configured to have the following functions:
MCU I/O – write to or read from a standard output or input port.
u
d
o
CPLD macrocell (McellBC0) output.
PC0
r
P
e
20
I/O
t
e
l
o
Input to the PLDs.
TMS Input2 for the JTAG Serial Interface.
This pin can be configured as a CMOS or Open Drain output.
bs
PC1 pin of Port C. This port pin can be configured to have the following functions:
MCU I/O – write to or read from a standard output or input port.
O
CPLD macrocell (McellBC1) output.
PC1
19
I/O
Input to the PLDs.
TCK Input2 for the JTAG Serial Interface.
This pin can be configured as a CMOS or Open Drain output.
Doc ID 10552 Rev 3
11/109
PSD813F2V, PSD854F2V
Pin Name
Pin
Type
Description
PC2 pin of Port C. This port pin can be configured to have the following functions:
MCU I/O – write to or read from a standard output or input port.
PC2
18
I/O
CPLD macrocell (McellBC2) output.
Input to the PLDs.
This pin can be configured as a CMOS or Open Drain output.
PC3 pin of Port C. This port pin can be configured to have the following functions:
MCU I/O – write to or read from a standard output or input port.
CPLD macrocell (McellBC3) output.
PC3
17
I/O
Input to the PLDs.
TSTAT output2 for the JTAG Serial Interface.
Ready/Busy output for parallel In-System Programming (ISP).
This pin can be configured as a CMOS or Open Drain output.
c
u
d
)
s
t(
PC4 pin of Port C. This port pin can be configured to have the following functions:
MCU I/O – write to or read from a standard output or input port.
CPLD macrocell (McellBC4) output.
PC4
14
I/O
Input to the PLDs.
TERR output2 for the JTAG Serial Interface.
e
t
le
o
r
P
o
s
b
O
-
This pin can be configured as a CMOS or Open Drain output.
PC5 pin of Port C. This port pin can be configured to have the following functions:
MCU I/O – write to or read from a standard output or input port.
)
s
(
ct
CPLD macrocell (McellBC5) output.
PC5
13
I/O
Input to the PLDs.
u
d
o
TDI input2 for the JTAG Serial Interface.
r
P
e
This pin can be configured as a CMOS or Open Drain output.
t
e
l
o
bs
PC6
O
12
PC6 pin of Port C. This port pin can be configured to have the following functions:
MCU I/O – write to or read from a standard output or input port.
CPLD macrocell (McellBC6) output.
I/O
Input to the PLDs.
TDO output2 for the JTAG Serial Interface.
This pin can be configured as a CMOS or Open Drain output.
12/109
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
Pin Name
Pin
Type
Description
PC7 pin of Port C. This port pin can be configured to have the following functions:
MCU I/O – write to or read from a standard output or input port.
CPLD macrocell (McellBC7) output.
PC7
11
I/O
Input to the PLDs.
DBE – active Low Data Byte Enable input from 68HC912 type MCUs.
This pin can be configured as a CMOS or Open Drain output.
PD0 pin of Port D. This port pin can be configured to have the following functions:
ALE/AS input latches address output from the MCU.
PD0
10
I/O
MCU I/O – write or read from a standard output or input port.
Input to the PLDs.
CPLD output (External Chip Select).
)
s
t(
PD1 pin of Port D. This port pin can be configured to have the following functions:
MCU I/O – write to or read from a standard output or input port.
c
u
d
Input to the PLDs.
PD1
9
I/O
CPLD output (External Chip Select).
o
r
P
CLKIN – clock input to the CPLD macrocells, the APD Unit’s Power-down counter, and
the CPLD AND Array.
e
t
le
PD2 pin of Port D. This port pin can be configured to have the following functions:
MCU I/O - write to or read from a standard output or input port.
Input to the PLDs.
PD2
8
I/O
o
s
b
O
-
CPLD output (External Chip Select).
)
s
(
ct
PSD Chip Select Input (CSI). When Low, the MCU can access the PSD memory and I/O.
When High, the PSD memory blocks are disabled to conserve power.
u
d
o
VCC
15, 38
Supply Voltage
GND
1, 16,
26
Ground pins
r
P
e
Note: 1. The pin numbers in this table are for the PLCC package only. See the package information from Table 75., page 105 and Table
77., page 107 for pin numbers on other package types.
2. These functions can be multiplexed with other functions.
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
13/109
r
P
e
s
b
O
14/109
Doc ID 10552 Rev 3
73
FLASH DECODE
PLD (DPLD)
CLKIN
FLASH ISP CPLD
(CPLD)
CLKIN
JTAG
SERIAL
CHANNEL
PORT A ,B & C
24 INPUT MACROCELLS
PORT A ,B & C
16 OUTPUT MACROCELLS
3 EXT CS TO PORT D
RUNTIME CONTROL
AND I/O REGISTERS
256 KBIT SRAM
256 KBIT SECONDARY
NON-VOLATILE MEMORY
(BOOT OR DATA)
4 SECTORS
8 SECTORS
1 OR 2 MBIT PRIMARY
FLASH MEMORY
c
u
d
PLD, CONFIGURATION
& FLASH MEMORY
LOADER
MACROCELL FEEDBACK OR PORT INPUT
73
CSIOP
PERIP I/O MODE SELECTS
SRAM SELECT
SECTOR
SELECTS
SECTOR
SELECTS
EMBEDDED
ALGORITHM
o
r
P
CLKIN
(PD1)
8
PAGE
REGISTER
u
d
o
)
s
(
ct
o
s
b
O
e
t
le
GLOBAL
CONFIG. &
SECURITY
ADIO
PORT
PROG.
MCU BUS
INTRF.
t
e
l
o
AD0 – AD15
CNTL0,
CNTL1,
CNTL2
PLD
INPUT
BUS
ADDRESS/DATA/CONTROL BUS
PORT
D
PROG.
PORT
PORT
C
PROG.
PORT
PORT
B
PROG.
PORT
PORT
A
PROG.
PORT
PD0 – PD2
PC0 – PC7
PB0 – PB7
PA0 – PA7
PSD813F2V, PSD854F2V
Figure 5. PSD Block Diagram
)
s
t(
AI02861G
PSD813F2V, PSD854F2V
PSD ARCHITECTURAL OVERVIEW
PSD devices contain several major functional
blocks. Figure 5 shows the architecture of the PSD
device family. The functions of each block are described briefly in the following sections. Many of
the blocks perform multiple functions and are user
configurable.
Memory
Each of the memory blocks is briefly discussed in
the following paragraphs. A more detailed discussion can be found in the section entitled Memory
Blocks, page 19.
The 1 Mbit or 2 Mbit (128K x 8, or 256K x 8) Flash
memory is the primary memory of the PSD. It is divided into 8 equally-sized sectors that are individually selectable.
The optional 256 Kbit (32K x 8) secondary Flash
memory is divided into 4 equally-sized sectors.
Each sector is individually selectable.
The optional SRAM is intended for use as a
scratch-pad memory or as an extension to the
MCU SRAM.
Each sector of memory can be located in a different address space as defined by the user. The access times for all memory types includes the
address latching and DPLD decoding time.
Page Register
The 8-bit Page Register expands the address
range of the MCU by up to 256 times. The paged
address can be used as part of the address space
to access external memory and peripherals, or internal memory and I/O. The Page Register can
also be used to change the address mapping of
sectors of the Flash memories into different memory spaces for IAP.
PLDs
The device contains two PLDs, the Decode PLD
(DPLD) and the Complex PLD (CPLD), as shown
in Table 3, each optimized for a different function.
The functional partitioning of the PLDs reduces
power consumption, optimizes cost/performance,
and eases design entry.
)
s
(
ct
c
u
d
e
t
le
)
s
t(
o
r
P
o
s
b
O
-
u
d
o
r
P
e
t
e
l
o
nal memory and registers. The DPLD has combinatorial outputs. The CPLD has 16 Output
Macrocells (OMC) and 3 combinatorial outputs.
The PSD also has 24 Input Macrocells (IMC) that
can be configured as inputs to the PLDs. The
PLDs receive their inputs from the PLD Input Bus
and are differentiated by their output destinations,
number of product terms, and macrocells.
The PLDs consume minimal power. The speed
and power consumption of the PLD is controlled
by the Turbo Bit in PMMR0 and other bits in the
PMMR2. These registers are set by the MCU at
run-time. There is a slight penalty to PLD propagation time when invoking the power management
features.
I/O Ports
The PSD has 27 individually configurable I/O pins
distributed over the four ports (Port A, B, C, and
D). Each I/O pin can be individually configured for
different functions. Ports can be configured as
standard MCU I/O ports, PLD I/O, or latched address outputs for MCUs using multiplexed address/data buses.
The JTAG pins can be enabled on Port C for InSystem Programming (ISP).
Ports A and B can also be configured as a data
port for a non-multiplexed bus.
MCU Bus Interface
PSD interfaces easily with most 8-bit MCUs that
have either multiplexed or non-multiplexed address/data buses. The device is configured to respond to the MCU’s control signals, which are also
used as inputs to the PLDs. For examples, please
see the section entitled MCU Bus Interface
Examples, page 45.
Table 3. PLD I/O
Inputs
Outputs
Product
Terms
Decode PLD (DPLD)
73
17
42
Complex PLD (CPLD)
73
19
140
Name
s
b
O
The DPLD is used to decode addresses and to
generate Sector Select signals for the PSD inter-
Doc ID 10552 Rev 3
15/109
PSD813F2V, PSD854F2V
JTAG Port
In-System Programming (ISP) can be performed
through the JTAG signals on Port C. This serial interface allows complete programming of the entire
PSD device. A blank device can be completely
programmed. The JTAG signals (TMS, TCK,
TSTAT, TERR, TDI, TDO) can be multiplexed with
other functions on Port C. Table 4 indicates the
JTAG pin assignments.
In-System Programming (ISP)
Using the JTAG signals on Port C, the entire PSD
device can be programmed or erased without the
use of the MCU. The primary Flash memory can
also be programmed in-system by the MCU executing the programming algorithms out of the secondary memory, or SRAM. The secondary
memory can be programmed the same way by executing out of the primary Flash memory. The PLD
or other PSD Configuration blocks can be programmed through the JTAG port or a device programmer. Table 5 indicates which programming
methods can program different functional blocks
of the PSD.
Power Management Unit (PMU)
The Power Management Unit (PMU) gives the
user control of the power consumption on selected
functional blocks based on system requirements.
The PMU includes an Automatic Power-down
(APD) Unit that turns off device functions during
MCU inactivity. The APD Unit has a Power-down
mode that helps reduce power consumption.
The PSD also has some bits that are configured at
run-time by the MCU to reduce power consumption of the CPLD. The Turbo Bit in PMMR0 can be
reset to '0' and the CPLD latches its outputs and
goes to sleep until the next transition on its inputs.
Additionally, bits in PMMR2 can be set by the
MCU to block signals from entering the CPLD to
reduce power consumption. Please see the section entitled POWER MANAGEMENT, page 62 for
more details.
Table 4. JTAG SIgnals on Port C
Port C Pins
JTAG Signal
PC0
TMS
PC1
TCK
PC3
TSTAT
PC4
TERR
PC5
TDI
PC6
TDO
e
t
le
c
u
d
)
s
t(
o
r
P
o
s
b
O
-
Table 5. Methods of Programming Different Functional Blocks of the PSD
(s)
Functional Block
ct
Primary Flash Memory
u
d
o
Secondary Flash Memory
PLD Array (DPLD and CPLD)
r
P
e
PSD Configuration
JTAG Programming
Device Programmer
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
No
t
e
l
o
s
b
O
16/109
Doc ID 10552 Rev 3
IAP
PSD813F2V, PSD854F2V
DEVELOPMENT SYSTEM
The PSD8XXFX family is supported by PSDsoft
Express, a Windows-based software development
tool. A PSD design is quickly and easily produced
in a point and click environment. The designer
does not need to enter Hardware Description Language (HDL) equations, unless desired, to define
PSD pin functions and memory map information.
The general design flow is shown in Figure 6.
PSDsoft Express is available from our web site
(the address is given on the back page of this data
sheet) or other distribution channels.
PSDsoft Express directly supports two low cost
device programmers form ST: PSDpro and FlashLINK (JTAG). Both of these programmers may be
purchased through your local distributor/representative, or directly from our web site using a credit
card. The PSD is also supported by third party device programmers. See our web site for the current
list.
Figure 6. PSDsoft Express Development Tool
PSDabel
PLD DESCRIPTION
MODIFY ABEL TEMPLATE FILE
OR GENERATE NEW FILE
PSD TOOLS
CONFIGURE MCU BUS
INTERFACE AND OTHER
PSD ATTRIBUTES
GENERATE C CODE
SPECIFIC TO PSD
FUNCTIONS
PSD Fitter
LOGIC SYNTHESIS
AND FITTING
)
s
(
ct
ADDRESS TRANSLATION
AND MEMORY MAPPING
o
r
P
e
t
e
l
o
o
r
P
PSD Configuration
du
e
t
le
o
s
b
O
FIRMWARE
HEX OR S-RECORD
FORMAT
c
u
d
)
s
t(
USER'S CHOICE OF
MICROCONTROLLER
COMPILER/LINKER
*.OBJ FILE
PSD Simulator
PSD Programmer
PSDsilos III
DEVICE SIMULATION
(OPTIONAL)
PSDPro, or
FlashLINK (JTAG)
s
b
O
*.OBJ AND *.SVF
FILES AVAILABLE
FOR 3rd PARTY
PROGRAMMERS
(CONVENTIONAL or
JTAG-ISC)
AI04918
Doc ID 10552 Rev 3
17/109
PSD813F2V, PSD854F2V
PSD REGISTER DESCRIPTION AND ADDRESS OFFSET
Table 6 shows the offset addresses to the PSD
registers relative to the CSIOP base address. The
CSIOP space is the 256 bytes of address that is allocated by the user to the internal PSD registers.
Table 7 provides brief descriptions of the registers
in CSIOP space. The following section gives a
more detailed description.
Table 6. I/O Port Latched Address Output Assignments (Note1)
Port A
MCU
Port A (3:0)
Port B
Port A (7:4)
Port B (3:0)
Port B (7:4)
8051XA (8-bit)
N/A
Address a7-a4
Address a11-a8
N/A
80C251 (page mode)
N/A
N/A
Address a11-a8
Address a15-a12
All other 8-bit multiplexed
Address a3-a0
Address a7-a4
Address a3-a0
Address a7-a4
8-bit non-multiplexed bus
N/A
N/A
Address a3-a0
Address a7-a4
Note: 1. See the section entitled I/O PORTS, page 51, on how to enable the Latched Address Output function.
2. N/A = Not Applicable
Table 7. Register Address Offset
Register Name
c
u
d
Other1
)
s
t(
Port A
Port B
Port C
Port D
Data In
00
01
10
11
Reads Port pin as input, MCU I/O input mode
Control
02
03
Selects mode between MCU I/O or Address Out
Description
o
r
P
Data Out
04
05
12
13
Stores data for output to Port pins, MCU I/O
output mode
Direction
06
07
14
15
Configures Port pin as input or output
Drive Select
08
09
16
17
Input Macrocell
0A
0B
18
Enable Out
0C
0D
1A
Output Macrocells
AB
20
20
ct
21
21
Output Macrocells
BC
r
P
e
Mask Macrocells AB
t
e
l
o
Mask Macrocells BC
Primary Flash
Protection
u
d
o
22
e
t
le
o
s
b
O
-
Configures Port pins as either CMOS or Open
Drain on some pins, while selecting high slew rate
on other pins.
Reads Input Macrocells
(s)
1B
Reads the status of the output enable to the I/O
Port driver
READ – reads output of macrocells AB
WRITE – loads macrocell flip-flops
READ – reads output of macrocells BC
WRITE – loads macrocell flip-flops
22
23
Blocks writing to the Output Macrocells AB
23
Blocks writing to the Output Macrocells BC
C0
Read only – Primary Flash Sector Protection
Secondary Flash
memory Protection
C2
Read only – PSD Security and Secondary Flash
memory Sector Protection
JTAG Enable
C7
Enables JTAG Port
PMMR0
B0
Power Management Register 0
PMMR2
B4
Power Management Register 2
Page
E0
Page Register
VM
E2
Places PSD memory areas in Program and/or
Data space on an individual basis.
s
b
O
Note: 1. Other registers that are not part of the I/O ports.
18/109
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
DETAILED OPERATION
As shown in Figure 5., page 14, the PSD consists
of six major types of functional blocks:
■
Memory Blocks
■
PLD Blocks
■
MCU Bus Interface
■
I/O Ports
■
Power Management Unit (PMU)
■
JTAG Interface
The functions of each block are described in the
following sections. Many of the blocks perform
multiple functions, and are user configurable.
Memory Blocks
The PSD has the following memory blocks:
– Primary Flash memory
– Optional Secondary Flash memory
– Optional SRAM
The Memory Select signals for these blocks originate from the Decode PLD (DPLD) and are userdefined in PSDsoft Express.
Table 8. Memory Block Size and Organization
Primary Flash Memory
Secondary Flash Memory
SRAM
)
s
t(
Sector
Number
Sector Size
(Bytes)
Sector Select
Signal
Sector Size
(Bytes)
Sector Select
Signal
SRAM Size
(Bytes)
SRAM Select
Signal
0
32K
FS0
16K
CSBOOT0
256K
RS0
1
32K
FS1
16K
CSBOOT1
2
32K
FS2
16K
CSBOOT2
3
32K
FS3
16K
CSBOOT3
4
32K
FS4
5
32K
FS5
6
32K
FS6
7
32K
FS7
Total
512K
8 Sectors
e
t
le
)
s
(
ct
o
s
b
O
64K
4 Sectors
c
u
d
o
r
P
256K
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
19/109
PSD813F2V, PSD854F2V
Primary Flash Memory and Secondary Flash
memory Description
The primary Flash memory is divided evenly into
eight equal sectors. The secondary Flash memory
is divided into four equal sectors. Each sector of
either memory block can be separately protected
from Program and Erase cycles.
Flash memory may be erased on a sector-by-sector basis. Flash sector erasure may be suspended
while data is read from other sectors of the block
and then resumed after reading.
During a Program or Erase cycle in Flash memory,
the status can be output on Ready/Busy (PC3).
This pin is set up using PSDsoft Express Configuration.
Memory Block Select Signals
The DPLD generates the Select signals for all the
internal memory blocks (see the section entitled
PLDS, page 33). Each of the eight sectors of the
primary Flash memory has a Select signal (FS0FS7) which can contain up to three product terms.
Each of the four sectors of the secondary Flash
memory has a Select signal (CSBOOT0CSBOOT3) which can contain up to three product
terms. Having three product terms for each Select
signal allows a given sector to be mapped in different areas of system memory. When using a MCU
with separate Program and Data space, these
flexible Select signals allow dynamic re-mapping
of sectors from one memory space to the other.
Ready/Busy (PC3). This signal can be used to
output the Ready/Busy status of the PSD. The output on Ready/Busy (PC3) is a 0 (Busy) when Flash
memory is being written to, or when Flash memory
is being erased. The output is a 1 (Ready) when
no WRITE or Erase cycle is in progress.
)
s
(
ct
Memory Operation. The primary Flash memory
and secondary Flash memory are addressed
through the MCU Bus Interface. The MCU can access these memories in one of two ways:
– The MCU can execute a typical bus WRITE or
READ operation just as it would if accessing a
RAM or ROM device using standard bus
cycles.
– The MCU can execute a specific instruction
that consists of several WRITE and READ
operations. This involves writing specific data
patterns to special addresses within the Flash
memory to invoke an embedded algorithm.
These instructions are summarized in Table
9., page 21.
Typically, the MCU can read Flash memory using
READ operations, just as it would read a ROM device. However, Flash memory can only be altered
using specific Erase and Program instructions. For
example, the MCU cannot write a single byte directly to Flash memory as it would write a byte to
RAM. To program a byte into Flash memory, the
MCU must execute a Program instruction, then
test the status of the Program cycle. This status
test is achieved by a READ operation or polling
Ready/Busy (PC3).
Flash memory can also be read by using special
instructions to retrieve particular Flash device information (sector protect status and ID).
e
t
le
o
s
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
20/109
c
u
d
Doc ID 10552 Rev 3
o
r
P
)
s
t(
PSD813F2V, PSD854F2V
Table 9. Instructions
FS0-FS7 or
CSBOOT0CSBOOT3
Cycle 1
READ5
1
“READ”
RD @ RA
Read Main
Flash ID6
1
Read Sector
Protection6,8,13
Instruction
Cycle 2
Cycle 3
Cycle 4
Cycle 5
Cycle 6
Cycle 7
AAh@
X555h
55h@
XAAAh
90h@
X555h
Read identifier
(A6,A1,A0 = 0,0,1)
1
AAh@
X555h
55h@
XAAAh
90h@
X555h
Read identifier
(A6,A1,A0 = 0,1,0)
Program a
Flash Byte13
1
AAh@
X555h
55h@
XAAAh
A0h@
X555h
PD@ PA
Flash Sector
Erase7,13
1
AAh@
X555h
55h@
XAAAh
80h@
X555h
AAh@ X555h
55h@
XAAAh
30h@
SA
30h7@
next SA
Flash Bulk
Erase13
1
AAh@
X555h
55h@
XAAAh
80h@
X555h
AAh@ X555h
55h@
XAAAh
10h@
X555h
Suspend
Sector Erase11
1
B0h@
XXXXh
Resume
Sector Erase12
1
30h@
XXXXh
Reset6
1
F0h@
XXXXh
Unlock Bypass
1
AAh@
X555h
55h@
XAAAh
Unlock Bypass
Program9
1
A0h@
XXXXh
PD@ PA
Unlock Bypass
Reset10
1
90h@
XXXXh
00h@
XXXXh
c
u
d
)
s
(
ct
e
t
le
20h@
X555h
)
s
t(
o
r
P
o
s
b
O
-
Note: 1. All bus cycles are WRITE bus cycles, except the ones with the “READ” label
2. All values are in hexadecimal:
X = Don’t Care. Addresses of the form XXXXh, in this table, must be even addresses
RA = Address of the memory location to be read
RD = Data read from location RA during the READ cycle
PA = Address of the memory location to be programmed. Addresses are latched on the falling edge of Write Strobe (WR, CNTL0).
PA is an even address for PSD in word programming mode.
PD = Data word to be programmed at location PA. Data is latched on the rising edge of Write Strobe (WR, CNTL0)
SA = Address of the sector to be erased or verified. The Sector Select (FS0-FS7 or CSBOOT0-CSBOOT3) of the sector to be
erased, or verified, must be Active (High).
3. Sector Select (FS0 to FS7 or CSBOOT0 to CSBOOT3) signals are active High, and are defined in PSDsoft Express.
4. Only address bits A11-A0 are used in instruction decoding.
5. No Unlock or instruction cycles are required when the device is in the READ Mode
6. The Reset instruction is required to return to the READ Mode after reading the Flash ID, or after reading the Sector Protection Status, or if the Error Flag Bit (DQ5/DQ13) goes High.
7. Additional sectors to be erased must be written at the end of the Sector Erase instruction within 80µs.
8. The data is 00h for an unprotected sector, and 01h for a protected sector. In the fourth cycle, the Sector Select is active, and
(A1,A0)=(1,0)
9. The Unlock Bypass instruction is required prior to the Unlock Bypass Program instruction.
10. The Unlock Bypass Reset Flash instruction is required to return to reading memory data when the device is in the Unlock Bypass
mode.
11. The system may perform READ and Program cycles in non-erasing sectors, read the Flash ID or read the Sector Protection Status
when in the Suspend Sector Erase mode. The Suspend Sector Erase instruction is valid only during a Sector Erase cycle.
12. The Resume Sector Erase instruction is valid only during the Suspend Sector Erase mode.
13. The MCU cannot invoke these instructions while executing code from the same Flash memory as that for which the instruction is
intended. The MCU must fetch, for example, the code from the secondary Flash memory when reading the Sector Protection Status
of the primary Flash memory.
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
21/109
PSD813F2V, PSD854F2V
INSTRUCTIONS
An instruction consists of a sequence of specific
operations. Each received byte is sequentially decoded by the PSD and not executed as a standard
WRITE operation. The instruction is executed
when the correct number of bytes are properly received and the time between two consecutive
bytes is shorter than the time-out period. Some instructions are structured to include READ operations after the initial WRITE operations.
The instruction must be followed exactly. Any invalid combination of instruction bytes or time-out
between two consecutive bytes while addressing
Flash memory resets the device logic into READ
Mode (Flash memory is read like a ROM device).
The PSD supports the instructions summarized in
Table 9., page 21:
Flash memory:
■
Erase memory by chip or sector
■
Suspend or resume sector erase
■
Program a Byte
■
Reset to READ Mode
■
Read primary Flash Identifier value
■
Read Sector Protection Status
■
Bypass (on the PSD833F2, PSD834F2,
PSD853F2 and PSD854F2)
These instructions are detailed in Table
9., page 21. For efficient decoding of the instructions, the first two bytes of an instruction are the
coded cycles and are followed by an instruction
byte or confirmation byte. The coded cycles consist of writing the data AAh to address X555h during the first cycle and data 55h to address XAAAh
during the second cycle. Address signals A15-A12
are Don’t Care during the instruction WRITE cycles. However, the appropriate Sector Select
(FS0-FS7 or CSBOOT0-CSBOOT3) must be selected.
The primary and secondary Flash memories have
the same instruction set (except for Read Primary
Flash Identifier). The Sector Select signals determine which Flash memory is to receive and execute the instruction. The primary Flash memory is
selected if any one of Sector Select (FS0-FS7) is
High, and the secondary Flash memory is selected
if any one of Sector Select (CSBOOT0CSBOOT3) is High.
Power-up Mode
The PSD internal logic is reset upon Power-up to
the READ Mode. Sector Select (FS0-FS7 and
CSBOOT0-CSBOOT3) must be held Low, and
Write Strobe (WR, CNTL0) High, during Power-up
)
s
(
ct
u
d
o
r
P
e
t
e
l
o
s
b
O
22/109
for maximum security of the data contents and to
remove the possibility of a byte being written on
the first edge of Write Strobe (WR, CNTL0). Any
WRITE cycle initiation is locked when VCC is below VLKO.
READ
Under typical conditions, the MCU may read the
primary Flash memory or the secondary Flash
memory using READ operations just as it would a
ROM or RAM device. Alternately, the MCU may
use READ operations to obtain status information
about a Program or Erase cycle that is currently in
progress. Lastly, the MCU may use instructions to
read special data from these memory blocks. The
following sections describe these READ functions.
Read Memory Contents
Primary Flash memory and secondary Flash
memory are placed in the READ Mode after Power-up, chip reset, or a Reset Flash instruction (see
Table 9., page 21). The MCU can read the memory contents of the primary Flash memory or the
secondary Flash memory by using READ operations any time the READ operation is not part of an
instruction.
Read Primary Flash Identifier
The primary Flash memory identifier is read with
an instruction composed of 4 operations: 3 specific
WRITE operations and a READ operation (see Table 9., page 21). During the READ operation, address bits A6, A1, and A0 must be '0,0,1,'
respectively, and the appropriate Sector Select
(FS0-FS7) must be High. The identifier for the
PSD813F2/3/4/5 is E4h, and for the PSD83xF2 or
PSD85xF2 it is E7h.
Read Memory Sector Protection Status
The primary Flash memory Sector Protection Status is read with an instruction composed of 4 operations: 3 specific WRITE operations and a READ
operation (see Table 9., page 21). During the
READ operation, address Bits A6, A1, and A0
must be '0,1,0,' respectively, while Sector Select
(FS0-FS7 or CSBOOT0-CSBOOT3) designates
the Flash memory sector whose protection has to
be verified. The READ operation produces 01h if
the Flash memory sector is protected, or 00h if the
sector is not protected.
The sector protection status for all NVM blocks
(primary Flash memory or secondary Flash memory) can also be read by the MCU accessing the
Flash Protection registers in PSD I/O space. See
the section entitled Flash Memory Sector
Protect, page 28 for register definitions.
c
u
d
o
s
b
O
-
e
t
le
Doc ID 10552 Rev 3
o
r
P
)
s
t(
PSD813F2V, PSD854F2V
Reading the Erase/Program Status Bits
The PSD provides several status bits to be used
by the MCU to confirm the completion of an Erase
or Program cycle of Flash memory. These status
bits minimize the time that the MCU spends performing these tasks and are defined in Table 10.
The status bits can be read as many times as
needed.
For Flash memory, the MCU can perform a READ
operation to obtain these status bits while an
Erase or Program instruction is being executed by
the embedded algorithm. See the section entitled
PROGRAMMING FLASH MEMORY, page 25 for
details.
Table 10. Status Bit
Functional Block
FS0-FS7/CSBOOT0CSBOOT3
VIH
Flash Memory
DQ7
DQ6
Data
Polling
Toggle
Flag
DQ5
Error
Flag
DQ4
X
DQ3
Erase
Timeout
DQ2
X
DQ1
X
Note: 1. X = Not guaranteed value, can be read either '1' or ’0.’
2. DQ7-DQ0 represent the Data Bus bits, D7-D0.
3. FS0-FS7 and CSBOOT0-CSBOOT3 are active High.
c
u
d
e
t
le
)
s
(
ct
DQ0
X
)
s
t(
o
r
P
o
s
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
23/109
PSD813F2V, PSD854F2V
Data Polling Flag (DQ7)
When erasing or programming in Flash memory,
the Data Polling Flag Bit (DQ7) outputs the complement of the bit being entered for programming/
writing on the DQ7 Bit. Once the Program instruction or the WRITE operation is completed, the true
logic value is read on the Data Polling Flag Bit
(DQ7, in a READ operation).
– Data Polling is effective after the fourth WRITE
pulse (for a Program instruction) or after the
sixth WRITE pulse (for an Erase instruction). It
must be performed at the address being
programmed or at an address within the Flash
memory sector being erased.
– During an Erase cycle, the Data Polling Flag
Bit (DQ7) outputs a ’0.’ After completion of the
cycle, the Data Polling Flag Bit (DQ7) outputs
the last bit programmed (it is a '1' after
erasing).
– If the byte to be programmed is in a protected
Flash memory sector, the instruction is
ignored.
– If all the Flash memory sectors to be erased
are protected, the Data Polling Flag Bit (DQ7)
is reset to '0' for about 100µs, and then returns
to the previous addressed byte. No erasure is
performed.
Toggle Flag (DQ6)
The PSD offers another way for determining when
the Flash memory Program cycle is completed.
During the internal WRITE operation and when either the FS0-FS7 or CSBOOT0-CSBOOT3 is true,
the Toggle Flag Bit (DQ6) toggles from '0' to '1' and
'1' to '0' on subsequent attempts to read any byte
of the memory.
When the internal cycle is complete, the toggling
stops and the data read on the Data Bus D0-D7 is
the addressed memory byte. The device is now
accessible for a new READ or WRITE operation.
The cycle is finished when two successive READs
yield the same output data.
)
s
(
ct
u
d
o
r
P
e
–
The Toggle Flag Bit (DQ6) is effective after the
fourth WRITE pulse (for a Program instruction)
or after the sixth WRITE pulse (for an Erase
instruction).
– If the byte to be programmed belongs to a
protected Flash memory sector, the
instruction is ignored.
– If all the Flash memory sectors selected for
erasure are protected, the Toggle Flag Bit
(DQ6) toggles to '0' for about 100µs and then
returns to the previous addressed byte.
Error Flag (DQ5)
During a normal Program or Erase cycle, the Error
Flag Bit (DQ5) is to ’0.’ This bit is set to '1' when
there is a failure during Flash memory Byte Program, Sector Erase, or Bulk Erase cycle.
In the case of Flash memory programming, the Error Flag Bit (DQ5) indicates the attempt to program
a Flash memory bit from the programmed state,
’0,’ to the erased state, '1,' which is not valid. The
Error Flag Bit (DQ5) may also indicate a Time-out
condition while attempting to program a byte.
In case of an error in a Flash memory Sector Erase
or Byte Program cycle, the Flash memory sector in
which the error occurred or to which the programmed byte belongs must no longer be used.
Other Flash memory sectors may still be used.
The Error Flag Bit (DQ5) is reset after a Reset
Flash instruction.
Erase Time-out Flag (DQ3)
The Erase Time-out Flag Bit (DQ3) reflects the
time-out period allowed between two consecutive
Sector Erase instructions. The Erase Time-out
Flag Bit (DQ3) is reset to '0' after a Sector Erase
cycle for a time period of 100µs + 20% unless an
additional Sector Erase instruction is decoded. After this time period, or when the additional Sector
Erase instruction is decoded, the Erase Time-out
Flag Bit (DQ3) is set to '1.'
e
t
le
o
s
b
O
-
t
e
l
o
s
b
O
24/109
c
u
d
Doc ID 10552 Rev 3
o
r
P
)
s
t(
PSD813F2V, PSD854F2V
PROGRAMMING FLASH MEMORY
Flash memory must be erased prior to being programmed. A byte of Flash memory is erased to all
1s (FFh), and is programmed by setting selected
bits to ’0.’ The MCU may erase Flash memory all
at once or by-sector, but not byte-by-byte. However, the MCU may program Flash memory byte-bybyte.
The primary and secondary Flash memories require the MCU to send an instruction to program a
byte or to erase sectors (see Table 9., page 21).
Once the MCU issues a Flash memory Program or
Erase instruction, it must check for the status bits
for completion. The embedded algorithms that are
invoked inside the PSD support several means to
provide status to the MCU. Status may be checked
using any of three methods: Data Polling, Data
Toggle, or Ready/Busy (PC3).
Data Polling
Polling on the Data Polling Flag Bit (DQ7) is a
method of checking whether a Program or Erase
cycle is in progress or has completed. Figure 7
shows the Data Polling algorithm.
When the MCU issues a Program instruction, the
embedded algorithm within the PSD begins. The
MCU then reads the location of the byte to be programmed in Flash memory to check status. The
Data Polling Flag Bit (DQ7) of this location becomes the complement of b7 of the original data
byte to be programmed. The MCU continues to
poll this location, comparing the Data Polling Flag
Bit (DQ7) and monitoring the Error Flag Bit (DQ5).
When the Data Polling Flag Bit (DQ7) matches b7
of the original data, and the Error Flag Bit (DQ5)
remains ’0,’ the embedded algorithm is complete.
If the Error Flag Bit (DQ5) is '1,' the MCU should
test the Data Polling Flag Bit (DQ7) again since
the Data Polling Flag Bit (DQ7) may have changed
simultaneously with the Error Flag Bit (DQ5, see
Figure 7).
The Error Flag Bit (DQ5) is set if either an internal
time-out occurred while the embedded algorithm
attempted to program the byte or if the MCU attempted to program a '1' to a bit that was not
erased (not erased is logic '0').
It is suggested (as with all Flash memories) to read
the location again after the embedded program-
)
s
(
ct
ming algorithm has completed, to compare the
byte that was written to the Flash memory with the
byte that was intended to be written.
When using the Data Polling method during an
Erase cycle, Figure 7 still applies. However, the
Data Polling Flag Bit (DQ7) is '0' until the Erase cycle is complete. A 1 on the Error Flag Bit (DQ5) indicates a time-out condition on the Erase cycle; a
0 indicates no error. The MCU can read any location within the sector being erased to get the Data
Polling Flag Bit (DQ7) and the Error Flag Bit
(DQ5).
PSDsoft Express generates ANSI C code functions which implement these Data Polling algorithms.
Figure 7. Data Polling Flowchart
START
c
u
d
READ DQ5 & DQ7
at VALID ADDRESS
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
e
t
le
so
b
O
-
u
d
o
)
s
t(
NO
o
r
P
DQ7
=
DATA
YES
NO
DQ5
=1
YES
READ DQ7
DQ7
=
DATA
YES
NO
FAIL
PASS
AI01369B
25/109
PSD813F2V, PSD854F2V
Data Toggle
Checking the Toggle Flag Bit (DQ6) is a method of
determining whether a Program or Erase cycle is
in progress or has completed. Figure 8 shows the
Data Toggle algorithm.
When the MCU issues a Program instruction, the
embedded algorithm within the PSD begins. The
MCU then reads the location of the byte to be programmed in Flash memory to check status. The
Toggle Flag Bit (DQ6) of this location toggles each
time the MCU reads this location until the embedded algorithm is complete. The MCU continues to
read this location, checking the Toggle Flag Bit
(DQ6) and monitoring the Error Flag Bit (DQ5).
When the Toggle Flag Bit (DQ6) stops toggling
(two consecutive reads yield the same value), and
the Error Flag Bit (DQ5) remains ’0,’ the embedded algorithm is complete. If the Error Flag Bit
(DQ5) is '1,' the MCU should test the Toggle Flag
Bit (DQ6) again, since the Toggle Flag Bit (DQ6)
may have changed simultaneously with the Error
Flag Bit (DQ5, see Figure 8).
The Error Flag Bit (DQ5) is set if either an internal
time-out occurred while the embedded algorithm
attempted to program the byte, or if the MCU attempted to program a '1' to a bit that was not
erased (not erased is logic '0').
It is suggested (as with all Flash memories) to read
the location again after the embedded programming algorithm has completed, to compare the
byte that was written to Flash memory with the
byte that was intended to be written.
When using the Data Toggle method after an
Erase cycle, Figure 8 still applies. the Toggle Flag
Bit (DQ6) toggles until the Erase cycle is complete.
A '1' on the Error Flag Bit (DQ5) indicates a timeout condition on the Erase cycle; a '0' indicates no
error. The MCU can read any location within the
sector being erased to get the Toggle Flag Bit
(DQ6) and the Error Flag Bit (DQ5).
PSDsoft Express generates ANSI C code functions which implement these Data Toggling algorithms.
Unlock Bypass (PSD833F2x, PSD834F2x,
PSD853F2x, PSD854F2x)
The Unlock Bypass instructions allow the system
to program bytes to the Flash memories faster
than using the standard Program instruction. The
Unlock Bypass mode is entered by first initiating
two Unlock cycles. This is followed by a third
WRITE cycle containing the Unlock Bypass code,
20h (as shown in Table 9., page 21).
)
s
(
ct
The Flash memory then enters the Unlock Bypass
mode. A two-cycle Unlock Bypass Program instruction is all that is required to program in this
mode. The first cycle in this instruction contains
the Unlock Bypass Program code, A0h. The second cycle contains the program address and data.
Additional data is programmed in the same manner. These instructions dispense with the initial
two Unlock cycles required in the standard Program instruction, resulting in faster total Flash
memory programming.
During the Unlock Bypass mode, only the Unlock
Bypass Program and Unlock Bypass Reset Flash
instructions are valid.
To exit the Unlock Bypass mode, the system must
issue the two-cycle Unlock Bypass Reset Flash instruction. The first cycle must contain the data
90h; the second cycle the data 00h. Addresses are
Don’t Care for both cycles. The Flash memory
then returns to READ Mode.
r
P
e
t
e
l
o
bs
O
Doc ID 10552 Rev 3
o
r
P
START
e
t
le
READ
DQ5 & DQ6
o
s
b
O
-
u
d
o
26/109
c
u
d
Figure 8. Data Toggle Flowchart
)
s
t(
DQ6
=
TOGGLE
NO
YES
NO
DQ5
=1
YES
READ DQ6
DQ6
=
TOGGLE
NO
YES
FAIL
PASS
AI01370B
PSD813F2V, PSD854F2V
ERASING FLASH MEMORY
Flash Bulk Erase
The Flash Bulk Erase instruction uses six WRITE
operations followed by a READ operation of the
status register, as described in Table 9., page 21.
If any byte of the Bulk Erase instruction is wrong,
the Bulk Erase instruction aborts and the device is
reset to the Read Flash memory status.
During a Bulk Erase, the memory status may be
checked by reading the Error Flag Bit (DQ5), the
Toggle Flag Bit (DQ6), and the Data Polling Flag
Bit (DQ7), as detailed in the section entitled PROGRAMMING FLASH MEMORY, page 25. The Error Flag Bit (DQ5) returns a '1' if there has been an
Erase Failure (maximum number of Erase cycles
have been executed).
It is not necessary to program the memory with
00h because the PSD automatically does this before erasing to 0FFh.
During execution of the Bulk Erase instruction, the
Flash memory does not accept any instructions.
Flash Sector Erase
The Sector Erase instruction uses six WRITE operations, as described in Table 9., page 21. Additional Flash Sector Erase codes and Flash
memory sector addresses can be written subsequently to erase other Flash memory sectors in
parallel, without further coded cycles, if the additional bytes are transmitted in a shorter time than
the time-out period of about 100µs. The input of a
new Sector Erase code restarts the time-out period.
The status of the internal timer can be monitored
through the level of the Erase Time-out Flag Bit
(DQ3). If the Erase Time-out Flag Bit (DQ3) is ’0,’
the Sector Erase instruction has been received
and the time-out period is counting. If the Erase
Time-out Flag Bit (DQ3) is '1,' the time-out period
has expired and the PSD is busy erasing the Flash
memory sector(s). Before and during Erase timeout, any instruction other than Suspend Sector
Erase and Resume Sector Erase instructions
abort the cycle that is currently in progress, and reset the device to READ Mode. It is not necessary
to program the Flash memory sector with 00h as
the PSD does this automatically before erasing
(byte = FFh).
During a Sector Erase, the memory status may be
checked by reading the Error Flag Bit (DQ5), the
Toggle Flag Bit (DQ6), and the Data Polling Flag
Bit (DQ7), as detailed in the section entitled PROGRAMMING FLASH MEMORY, page 25.
)
s
(
ct
u
d
o
r
P
e
s
b
O
t
e
l
o
During execution of the Erase cycle, the Flash
memory accepts only Reset and Suspend Sector
Erase instructions. Erasure of one Flash memory
sector may be suspended, in order to read data
from another Flash memory sector, and then resumed.
Suspend Sector Erase
When a Sector Erase cycle is in progress, the Suspend Sector Erase instruction can be used to suspend the cycle by writing 0B0h to any address
when an appropriate Sector Select (FS0-FS7 or
CSBOOT0-CSBOOT3) is High. (See Table
9., page 21). This allows reading of data from another Flash memory sector after the Erase cycle
has been suspended. Suspend Sector Erase is
accepted only during an Erase cycle and defaults
to READ Mode. A Suspend Sector Erase instruction executed during an Erase time-out period, in
addition to suspending the Erase cycle, terminates
the time out period.
The Toggle Flag Bit (DQ6) stops toggling when the
PSD internal logic is suspended. The status of this
bit must be monitored at an address within the
Flash memory sector being erased. The Toggle
Flag Bit (DQ6) stops toggling between 0.1µs and
15µs after the Suspend Sector Erase instruction
has been executed. The PSD is then automatically
set to READ Mode.
If an Suspend Sector Erase instruction was executed, the following rules apply:
– Attempting to read from a Flash memory
sector that was being erased outputs invalid
data.
– Reading from a Flash sector that was not
being erased is valid.
– The Flash memory cannot be programmed,
and only responds to Resume Sector Erase
and Reset Flash instructions (READ is an
operation and is allowed).
– If a Reset Flash instruction is received, data in
the Flash memory sector that was being
erased is invalid.
Resume Sector Erase
If a Suspend Sector Erase instruction was previously executed, the erase cycle may be resumed
with this instruction. The Resume Sector Erase instruction consists of writing 030h to any address
while an appropriate Sector Select (FS0-FS7 or
CSBOOT0-CSBOOT3) is High. (See Table
9., page 21.)
c
u
d
e
t
le
)
s
t(
o
r
P
o
s
b
O
-
Doc ID 10552 Rev 3
27/109
PSD813F2V, PSD854F2V
SPECIFIC FEATURES
Flash Memory Sector Protect
Each primary and secondary Flash memory sector
can be separately protected against Program and
Erase cycles. Sector Protection provides additional data security because it disables all Program or
Erase cycles. This mode can be activated through
the JTAG Port or a Device Programmer.
Sector protection can be selected for each sector
using the PSDsoft Express Configuration program. This automatically protects selected sectors
when the device is programmed through the JTAG
Port or a Device Programmer. Flash memory sectors can be unprotected to allow updating of their
contents using the JTAG Port or a Device Programmer. The MCU can read (but cannot change)
the sector protection bits.
Any attempt to program or erase a protected Flash
memory sector is ignored by the device. The Verify
operation results in a READ of the protected data.
This allows a guarantee of the retention of the Protection status.
The sector protection status can be read by the
MCU through the Flash memory protection and
PSD/EE protection registers (in the CSIOP block).
See Tables 11 and 12.
Reset Flash
The Reset Flash instruction consists of one
WRITE cycle (see Table 9., page 21). It can also
be optionally preceded by the standard two
WRITE decoding cycles (writing AAh to 555h and
55h to AAAh). It must be executed after:
– Reading the Flash Protection Status or Flash
ID
– An Error condition has occurred (and the
device has set the Error Flag Bit (DQ5) to '1')
during a Flash memory Program or Erase
cycle.
)
s
(
ct
c
u
d
e
t
le
)
s
t(
o
r
P
o
s
b
O
-
u
d
o
r
P
e
On the PSD813F2/3/4/5, the Reset Flash instruction puts the Flash memory back into normal
READ Mode. It may take the Flash memory up to
a few milliseconds to complete the Reset cycle.
The Reset Flash instruction is ignored when it is issued during a Program or Bulk Erase cycle of the
Flash memory. The Reset Flash instruction aborts
any on-going Sector Erase cycle, and returns the
Flash memory to the normal READ Mode within a
few milliseconds.
On the PSD83xF2 or PSD85xF2, the Reset Flash
instruction puts the Flash memory back into normal READ Mode. If an Error condition has occurred (and the device has set the Error Flag Bit
(DQ5) to '1') the Flash memory is put back into normal READ Mode within 25μs of the Reset Flash instruction having been issued. The Reset Flash
instruction is ignored when it is issued during a
Program or Bulk Erase cycle of the Flash memory.
The Reset Flash instruction aborts any on-going
Sector Erase cycle, and returns the Flash memory
to the normal READ Mode within 25μs.
Reset (RESET) Signal (on the PSD83xF2 and
PSD85xF2)
A pulse on Reset (RESET) aborts any cycle that is
in progress, and resets the Flash memory to the
READ Mode. When the reset occurs during a Program or Erase cycle, the Flash memory takes up
to 25μs to return to the READ Mode. It is recommended that the Reset (RESET) pulse (except for
Power On Reset, as described on RESET TIMING
AND DEVICE STATUS AT RESET, page 67) be
at least 25μs so that the Flash memory is always
ready for the MCU to fetch the bootstrap instructions after the Reset cycle is complete.
Table 11. Sector Protection/Security Bit Definition – Flash Protection Register
t
e
l
o
Bit 7
Sec7_Prot
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Sec6_Prot
Sec5_Prot
Sec4_Prot
Sec3_Prot
Sec2_Prot
Sec1_Prot
Sec0_Prot
s
b
O
Note: 1. Bit Definitions:
Sec<i>_Prot 1 = Primary Flash memory or secondary Flash memory Sector <i> is write protected.
Sec<i>_Prot 0 = Primary Flash memory or secondary Flash memory Sector <i> is not write protected.
Table 12. Sector Protection/Security Bit Definition – PSD/EE Protection Register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Security_Bit
not used
not used
not used
Sec3_Prot
Sec2_Prot
Sec1_Prot
Sec0_Prot
Note: 1. Bit Definitions:
Sec<i>_Prot 1 = Secondary Flash memory Sector <i> is write protected.
Sec<i>_Prot 0 = Secondary Flash memory Sector <i> is not write protected.
Security_Bit 0 = Security Bit in device has not been set.
1 = Security Bit in device has been set.
28/109
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
SRAM
The SRAM is enabled when SRAM Select (RS0)
from the DPLD is High. SRAM Select (RS0) can
contain up to two product terms, allowing flexible
memory mapping.
SRAM Select (RS0) is configured using PSDsoft
Express Configuration.
c
u
d
e
t
le
)
s
(
ct
)
s
t(
o
r
P
o
s
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
29/109
PSD813F2V, PSD854F2V
SECTOR SELECT AND SRAM SELECT
Sector Select (FS0-FS7, CSBOOT0-CSBOOT3)
and SRAM Select (RS0) are all outputs of the
DPLD. They are setup by writing equations for
them in PSDabel. The following rules apply to the
equations for these signals:
1. Primary Flash memory and secondary Flash
memory Sector Select signals must not be
larger than the physical sector size.
2. Any primary Flash memory sector must not be
mapped in the same memory space as
another Flash memory sector.
3. A secondary Flash memory sector must not be
mapped in the same memory space as
another secondary Flash memory sector.
4. SRAM, I/O, and Peripheral I/O spaces must
not overlap.
5. A secondary Flash memory sector may
overlap a primary Flash memory sector. In
case of overlap, priority is given to the
secondary Flash memory sector.
6. SRAM, I/O, and Peripheral I/O spaces may
overlap any other memory sector. Priority is
given to the SRAM, I/O, or Peripheral I/O.
Example
FS0 is valid when the address is in the range of
8000h to BFFFh, CSBOOT0 is valid from 8000h to
9FFFh, and RS0 is valid from 8000h to 87FFh.
Any address in the range of RS0 always accesses
the SRAM. Any address in the range of CSBOOT0
greater than 87FFh (and less than 9FFFh) automatically addresses secondary Flash memory
segment 0. Any address greater than 9FFFh accesses the primary Flash memory segment 0. You
can see that half of the primary Flash memory segment 0 and one-fourth of secondary Flash memory
segment 0 cannot be accessed in this example.
Also note that an equation that defined FS1 to anywhere in the range of 8000h to BFFFh would not
be valid.
Figure 9 shows the priority levels for all memory
components. Any component on a higher level can
overlap and has priority over any component on a
lower level. Components on the same level must
not overlap. Level one has the highest priority and
level 3 has the lowest.
Memory Select Configuration for MCUs with
Separate Program and Data Spaces
The 8031 and compatible family of MCUs, which
includes the 80C51, 80C151, 80C251, and
80C51XA, have separate address spaces for Program memory (selected using Program Select Enable (PSEN, CNTL2)) and Data memory (selected
using Read Strobe (RD, CNTL1)). Any of the
memories within the PSD can reside in either
space or both spaces.
)
s
(
ct
u
d
o
r
P
e
t
e
l
o
s
b
O
30/109
This is controlled through manipulation of the VM
register that resides in the CSIOP space.
The VM register is set using PSDsoft Express to
have an initial value. It can subsequently be
changed by the MCU so that memory mapping
can be changed on-the-fly.
For example, you may wish to have SRAM and primary Flash memory in the Data space at Boot-up,
and secondary Flash memory in the Program
space at Boot-up, and later swap the primary and
secondary Flash memories. This is easily done
with the VM register by using PSDsoft Express
Configuration to configure it for Boot-up and having the MCU change it when desired. Table
13., page 31 describes the VM Register.
Figure 9. Priority Level of Memory and I/O
Components
c
u
d
Highest Priority
e
t
le
o
s
b
O
-
Lowest Priority
)
s
t(
o
r
P
Level 1
SRAM, I /O, or
Peripheral I /O
Level 2
Secondary
Non-Volatile Memory
Level 3
Primary Flash Memory
AI02867D
Configuration Modes for MCUs with Separate
Program and Data Spaces
Separate Space Modes. Program space is separated from Data space. For example, Program
Select Enable (PSEN, CNTL2) is used to access
the program code from the primary Flash memory,
while Read Strobe (RD, CNTL1) is used to access
data from the secondary Flash memory, SRAM
and I/O Port blocks. This configuration requires
the VM register to be set to 0Ch (see Figure
10., page 31).
Combined Space Modes. The Program and
Data spaces are combined into one memory
space that allows the primary Flash memory, secondary Flash memory, and SRAM to be accessed
by either Program Select Enable (PSEN, CNTL2)
or Read Strobe (RD, CNTL1). For example, to
configure the primary Flash memory in Combined
space, Bits b2 and b4 of the VM register are set to
'1' (see Figure 11., page 31).
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
Figure 10. 8031 Memory Modules – Separate Space
DPLD
Primary
Flash
Memory
RS0
Secondary
Flash
Memory
SRAM
CSBOOT0-3
FS0-FS7
CS
CS
OE
CS
OE
OE
PSEN
RD
AI02869C
Figure 11. 8031 Memory Modules – Combined Space
DPLD
RD
Primary
Flash
Memory
RS0
Secondary
Flash
Memory
SRAM
d
o
r
CSBOOT0-3
FS0-FS7
P
e
let
CS
CS
OE
OE
VM REG BIT 3
VM REG BIT 4
PSEN
)
s
(
ct
VM REG BIT 1
CS
RD
r
P
e
VM REG BIT 0
t
e
l
o
OE
o
s
b
O
-
u
d
o
VM REG BIT 2
uc
)
s
t(
AI02870C
Table 13. VM Register
Bit 7
PIO_EN
Bit 6
Bit 5
Bit 4
Primary
FL_Data
Bit 3
Secondary
EE_Data
Bit 2
Primary
FL_Code
Bit 1
Secondary
EE_Code
Bit 0
SRAM_Code
0 = disable
PIO mode
not
used
not
used
0 = RD
can’t access
Flash memory
0 = RD can’t
access
Secondary Flash
memory
0 = PSEN
can’t access
Flash
memory
0 = PSEN can’t
access
Secondary Flash
memory
0 = PSEN
can’t access
SRAM
1= enable
PIO mode
not
used
not
used
1 = RD
access Flash
memory
1 = RD access
Secondary Flash
memory
1 = PSEN
access
Flash
memory
1 = PSEN access
Secondary Flash
memory
1 = PSEN
access
SRAM
s
b
O
Doc ID 10552 Rev 3
31/109
PSD813F2V, PSD854F2V
PAGE REGISTER
The 8-bit Page Register increases the addressing
capability of the MCU by a factor of up to 256. The
contents of the register can also be read by the
MCU. The outputs of the Page Register (PGR0PGR7) are inputs to the DPLD decoder and can be
included in the Sector Select (FS0-FS7,
CSBOOT0-CSBOOT3), and SRAM Select (RS0)
equations.
If memory paging is not needed, or if not all 8 page
register bits are needed for memory paging, then
these bits may be used in the CPLD for general
logic. See Application Note AN1154.
Figure 12 shows the Page Register. The eight flipflops in the register are connected to the internal
data bus D0-D7. The MCU can write to or read
from the Page Register. The Page Register can be
accessed at address location CSIOP + E0h.
Figure 12. Page Register
RESET
D0
D0 - D7
Q0
D1
Q1
D2
Q2
D3
Q3
D4
Q4
PGR0
INTERNAL
SELECTS
AND LOGIC
PGR1
PGR2
DPLD
AND
CPLD
PGR3
PGR4
PGR5
D5
Q5
D6
Q6
PGR6
PGR7
R/W
D7
PAGE
REGISTER
)
s
(
ct
so
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
32/109
e
t
le
Q7
Doc ID 10552 Rev 3
c
u
d
)
s
t(
o
r
P
PLD
AI02871B
PSD813F2V, PSD854F2V
PLDS
The PLDs bring programmable logic functionality
to the PSD. After specifying the logic for the PLDs
using the PSDabel tool in PSDsoft Express, the
logic is programmed into the device and available
upon Power-up.
The PSD contains two PLDs: the Decode PLD
(DPLD), and the Complex PLD (CPLD). The PLDs
are briefly discussed in the next few paragraphs,
and in more detail in the section entitled Decode
PLD (DPLD), page 35 and the section entitled
Complex
PLD
(CPLD), page 36.
Figure
13., page 34 shows the configuration of the PLDs.
The DPLD performs address decoding for Select
signals for internal components, such as memory,
registers, and I/O ports.
The CPLD can be used for logic functions, such as
loadable counters and shift registers, state machines, and encoding and decoding logic. These
logic functions can be constructed using the 16
Output Macrocells (OMC), 24 Input Macrocells
(IMC), and the AND Array. The CPLD can also be
used to generate External Chip Select (ECS0ECS2) signals.
The AND Array is used to form product terms.
These product terms are specified using PSDabel.
An Input Bus consisting of 73 signals is connected
to the PLDs. The signals are shown in Table 14.
The Turbo Bit in PSD
The PLDs in the PSD can minimize power consumption by switching off when inputs remain unchanged for an extended time of about 70ns.
Resetting the Turbo Bit to '0' (Bit 3 of PMMR0) automatically places the PLDs into standby if no inputs are changing. Turning the Turbo mode off
increases propagation delays while reducing power consumption. See the section entitled POWER
MANAGEMENT, page 62 on how to set the Turbo
Bit.
o
r
P
e
c
u
d
(t s)
Additionally, five bits are available in PMMR2 to
block MCU control signals from entering the PLDs.
This reduces power consumption and can be used
only when these MCU control signals are not used
in PLD logic equations.
Each of the two PLDs has unique characteristics
suited for its applications. They are described in
the following sections.
Table 14. DPLD and CPLD Inputs
Input Source
MCU Address Bus1
MCU Control Signals
Input Name
Number
of
Signals
A15-A0
16
CNTL2-CNTL0
3
Reset
RST
Power-down
PDN
Port A Input
Macrocells
PA7-PA0
Port B Input
Macrocells
c
u
d
o
r
P
)
s
t(
1
1
8
PB7-PB0
8
PC7-PC0
8
PD2-PD0
3
Page Register
PGR7-PGR0
8
Macrocell AB
Feedback
MCELLAB.FB7FB0
8
Macrocell BC
Feedback
MCELLBC.FB7FB0
8
Ready/Busy
1
e
t
le
Port C Input
Macrocells
so
Port D Inputs
b
O
-
Secondary Flash
memory Program
Status Bit
Note: 1. The address inputs are A19-A4 in 80C51XA mode.
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
33/109
34/109
PLD INPUT BUS
s
b
O
8
DECODE PLD
PAGE
REGISTER
16
1
2
1
1
4
8
CPLD
PT
ALLOC.
OUTPUT MACROCELL FEEDBACK
o
s
b
O
-
t
e
l
o
Doc ID 10552 Rev 3
16 OUTPUT
MACROCELL
INPUT MACROCELL & INPUT PORTS
PORT D INPUTS
24
3
MACROCELL
ALLOC.
AI02872C
3
8
MCELLBC
TO PORT B OR C
EXTERNAL CHIP SELECTS
TO PORT D
8
MCELLAB
TO PORT A OR B
DIRECT MACROCELL ACCESS FROM MCU DATA BUS
JTAG SELECT
PERIPHERAL SELECTS
CSIOP SELECT
SRAM SELECT
SECONDARY NON-VOLATILE MEMORY SELECTS
PRIMARY FLASH MEMORY SELECTS
24 INPUT MACROCELL
(PORT A,B,C)
e
t
le
o
r
P
DIRECT MACROCELL INPUT TO MCU DATA BUS
73
73
u
d
o
)
s
(
ct
I/O PORTS
r
P
e
DATA
BUS
PSD813F2V, PSD854F2V
Figure 13. PLD Diagram
c
u
d
)
s
t(
PSD813F2V, PSD854F2V
Decode PLD (DPLD)
The DPLD, shown in Figure 14, is used for decoding the address for internal and external components. The DPLD can be used to generate the
following decode signals:
■
8 Sector Select (FS0-FS7) signals for the
primary Flash memory (three product terms
each)
■
4 Sector Select (CSBOOT0-CSBOOT3)
signals for the secondary Flash memory (three
product terms each)
■
■
■
■
1 internal SRAM Select (RS0) signal (two
product terms)
1 internal CSIOP Select (PSD Configuration
Register) signal
1 JTAG Select signal (enables JTAG on Port
C)
2 internal Peripheral Select signals
(Peripheral I/O mode).
Figure 14. DPLD Logic Array
(INPUTS)
I /O PORTS (PORT A,B,C)
3
CSBOOT 0
3
CSBOOT 1
3
CSBOOT 2
3
CSBOOT 3
3
3
MCELLAB.FB [7:0] (FEEDBACKS)
(8)
MCELLBC.FB [7:0] (FEEDBACKS)
(8)
3
3
e
t
le
(8)
PGR0 - PGR7
3
(16)
A[15:0] *
(3)
PD[2:0] (ALE,CLKIN,CSI)
(1)
PDN (APD OUTPUT)
CNTRL[2:0] (READ/WRITE CONTROL SIGNALS)
(3)
RESET
(1)
RD_BSY
(1)
(s)
o
s
b
O
-
ct
o
r
P
e
du
c
u
d
FS0
(24)
FS1
o
r
P
FS2
FS3
)
s
t(
8 PRIMARY FLASH
MEMORY SECTOR SELECTS
FS4
3
FS5
3
FS6
3
FS7
2
RS0
1
CSIOP
1
PSEL0
1
PSEL1
1
JTAGSEL
SRAM SELECT
I/O DECODER
SELECT
PERIPHERAL I/O MODE
SELECT
AI02873D
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
35/109
PSD813F2V, PSD854F2V
Complex PLD (CPLD)
The CPLD can be used to implement system logic
functions, such as loadable counters and shift registers, system mailboxes, handshaking protocols,
state machines, and random logic. The CPLD can
also be used to generate three External Chip Select (ECS0-ECS2), routed to Port D.
Although External Chip Select (ECS0-ECS2) can
be produced by any Output Macrocell (OMC),
these three External Chip Select (ECS0-ECS2) on
Port D do not consume any Output Macrocells
(OMC).
As shown in Figure 13., page 34, the CPLD has
the following blocks:
■
24 Input Macrocells (IMC)
■
16 Output Macrocells (OMC)
■
Macrocell Allocator
Product Term Allocator
■
AND Array capable of generating up to 137
product terms
■
Four I/O Ports.
Each of the blocks are described in the sections
that follow.
The Input Macrocells (IMC) and Output Macrocells
(OMC) are connected to the PSD internal data bus
and can be directly accessed by the MCU. This
enables the MCU software to load data into the
Output Macrocells (OMC) or read data from both
the Input and Output Macrocells (IMC and OMC).
This feature allows efficient implementation of system logic and eliminates the need to connect the
data bus to the AND Array as required in most
standard PLD macrocell architectures.
■
Figure 15. Macrocell and I/O Port
PLD INPUT BUS
PRODUCT TERMS
FROM OTHER
MACROCELLS
TO OTHER I/O PORTS
CPLD MACROCELLS
DATA
LOAD
CONTROL
PT PRESET
MCU DATA IN
LATCHED
ADDRESS OUT
so
UP TO 10
PRODUCT TERMS
AND ARRAY
e
t
le
DATA
MCU LOAD
MUX
POLARITY
SELECT
PR DI LD
D/T
MUX
PT
CLOCK
GLOBAL
CLOCK
CLOCK
SELECT
Q
)
s
(
ct
D/T/JK FF
SELECT
CK
u
d
o
PT CLEAR
o
r
P
I/O PORTS
PRODUCT TERM
ALLOCATOR
PLD INPUT BUS
c
u
d
MCU ADDRESS / DATA BUS
)
s
t(
CL
COMB.
/REG
SELECT
MACROCELL
OUT TO
MCU
b
O
-
CPLD
OUTPUT
MUX
WR
CPLD OUTPUT
SELECT
PDR
MACROCELL
TO
I/O PORT
ALLOC.
r
P
e
I/O PIN
Q
D
INPUT
Q
DIR
REG.
D
WR
PT OUTPUT ENABLE (OE)
MACROCELL FEEDBACK
bs
MUX
PT INPUT LATCH GATE/CLOCK
ALE/AS
Q D
Q D
G
AI02874
O
36/109
MUX
t
e
l
o
INPUT MACROCELLS
I/O PORT INPUT
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
Output Macrocell (OMC)
Eight of the Output Macrocells (OMC) are connected to Ports A and B pins and are named as
McellAB0-McellAB7. The other eight macrocells
are connected to Ports B and C pins and are
named as McellBC0-McellBC7. If an McellAB output is not assigned to a specific pin in PSDabel,
the Macrocell Allocator block assigns it to either
Port A or B. The same is true for a McellBC output
on Port B or C. Table 15 shows the macrocells and
port assignment.
The Output Macrocell (OMC) architecture is
shown in Figure 16., page 39. As shown in the figure, there are native product terms available from
the AND Array, and borrowed product terms available (if unused) from other Output Macrocells
(OMC). The polarity of the product term is con-
trolled by the XOR gate. The Output Macrocell
(OMC) can implement either sequential logic, using the flip-flop element, or combinatorial logic.
The multiplexer selects between the sequential or
combinatorial logic outputs. The multiplexer output
can drive a port pin and has a feedback path to the
AND Array inputs.
The flip-flop in the Output Macrocell (OMC) block
can be configured as a D, T, JK, or SR type in the
PSDabel program. The flip-flop’s clock, preset,
and clear inputs may be driven from a product
term of the AND Array. Alternatively, CLKIN (PD1)
can be used for the clock input to the flip-flop. The
flip-flop is clocked on the rising edge of CLKIN
(PD1). The preset and clear are active High inputs.
Each clear input can use up to two product terms.
Table 15. Output Macrocell Port and Data Bit Assignments
)
s
t(
Output
Macrocell
Port
Assignment
Native Product Terms
Maximum Borrowed
Product Terms
Data Bit for Loading or
Reading
McellAB0
Port A0, B0
3
6
D0
McellAB1
Port A1, B1
3
6
McellAB2
Port A2, B2
3
McellAB3
Port A3, B3
3
McellAB4
Port A4, B4
3
McellAB5
Port A5, B5
3
McellAB6
Port A6, B6
3
McellAB7
Port A7, B7
3
McellBC0
Port B0, C0
McellBC1
Port B1, C1
McellBC2
Port B2, C2
McellBC4
t
e
l
o
McellBC5
McellBC6
bs
McellBC7
6
D1
D2
6
D3
6
D4
6
D5
6
D6
6
D7
5
D0
4
5
D1
4
5
D2
Port B3, C3
4
5
D3
Port B4, C4
4
6
D4
Port B5, C5
4
6
D5
Port B6, C6
4
6
D6
Port B7, C7
4
6
D7
o
r
P
e
McellBC3
P
e
let
ro
c
u
d
(s)
4
du
ct
o
s
b
O
-
O
Doc ID 10552 Rev 3
37/109
PSD813F2V, PSD854F2V
Product Term Allocator
The CPLD has a Product Term Allocator. The PSDabel compiler uses the Product Term Allocator to
borrow and place product terms from one macrocell to another. The following list summarizes how
product terms are allocated:
■
McellAB0-McellAB7 all have three native
product terms and may borrow up to six more
■
McellBC0-McellBC3 all have four native
product terms and may borrow up to five more
■
McellBC4-McellBC7 all have four native
product terms and may borrow up to six more.
Each macrocell may only borrow product terms
from certain other macrocells. Product terms already in use by one macrocell are not available for
another macrocell.
If an equation requires more product terms than
are available to it, then “external” product terms
are required, which consume other Output Macrocells (OMC). If external product terms are used,
extra delay is added for the equation that required
the extra product terms.
This is called product term expansion. PSDsoft
Express performs this expansion as needed.
Loading and Reading the Output Macrocells
(OMC)
The Output Macrocells (OMC) block occupies a
memory location in the MCU address space, as
defined by the CSIOP block (see the section entitled I/O PORTS, page 51). The flip-flops in each of
the 16 Output Macrocells (OMC) can be loaded
from the data bus by a MCU. Loading the Output
Macrocells (OMC) with data from the MCU takes
priority over internal functions. As such, the preset,
clear, and clock inputs to the flip-flop can be overridden by the MCU. The ability to load the flip-flops
and read them back is useful in such applications
as loadable counters and shift registers, mailboxes, and handshaking protocols.
)
s
(
ct
u
d
o
Data can be loaded to the Output Macrocells
(OMC) on the trailing edge of Write Strobe (WR,
CNTL0) (edge loading) or during the time that
Write Strobe (WR, CNTL0) is active (level loading). The method of loading is specified in PSDsoft
Express Configuration.
The OMC Mask Register
There is one Mask Register for each of the two
groups of eight Output Macrocells (OMC). The
Mask Registers can be used to block the loading
of data to individual Output Macrocells (OMC).
The default value for the Mask Registers is 00h,
which allows loading of the Output Macrocells
(OMC). When a given bit in a Mask Register is set
to a 1, the MCU is blocked from writing to the associated Output Macrocells (OMC). For example,
suppose McellAB0-McellAB3 are being used for a
state machine. You would not want a MCU write to
McellAB to overwrite the state machine registers.
Therefore, you would want to load the Mask Register for McellAB (Mask Macrocell AB) with the value 0Fh.
The Output Enable of the OMC
The Output Macrocells (OMC) block can be connected to an I/O port pin as a PLD output. The output enable of each port pin driver is controlled by
a single product term from the AND Array, ORed
with the Direction Register output. The pin is enabled upon Power-up if no output enable equation
is defined and if the pin is declared as a PLD output in PSDsoft Express.
If the Output Macrocell (OMC) output is declared
as an internal node and not as a port pin output in
the PSDabel file, the port pin can be used for other
I/O functions. The internal node feedback can be
routed as an input to the AND Array.
e
t
le
o
s
b
O
-
r
P
e
t
e
l
o
s
b
O
38/109
c
u
d
Doc ID 10552 Rev 3
o
r
P
)
s
t(
s
b
O
t
e
l
o
PLD INPUT BUS
PT
PT
PRESET(.PR)
ENABLE (.OE)
Doc ID 10552 Rev 3
PORT INPUT
Q
MUX
COMB/REG
SELECT
DIRECTION
REGISTER
D [ 7:0]
MACROCELL
ALLOCATOR
INTERNAL DATA BUS
PROGRAMMABLE
FF (D / T/JK /SR)
CLR
IN
LD
DIN PR
e
t
le
FEEDBACK (.FB)
MUX
CLEAR (.RE)
POLARITY
SELECT
o
s
b
O
-
CLKIN
WR
)
s
(
ct
PT CLK
PT
PT
ALLOCATOR
RD
MACROCELL CS
r
P
e
u
d
o
AND ARRAY
MASK
REG.
INPUT
MACROCELL
PORT
DRIVER
AI02875B
I/O PIN
PSD813F2V, PSD854F2V
Figure 16. CPLD Output Macrocell
c
u
d
)
s
t(
o
r
P
39/109
PSD813F2V, PSD854F2V
Input Macrocells (IMC)
The CPLD has 24 Input Macrocells (IMC), one for
each pin on Ports A, B, and C. The architecture of
the Input Macrocells (IMC) is shown in Figure
17., page 41. The Input Macrocells (IMC) are individually configurable, and can be used as a latch,
register, or to pass incoming Port signals prior to
driving them onto the PLD input bus. The outputs
of the Input Macrocells (IMC) can be read by the
MCU through the internal data bus.
The enable for the latch and clock for the register
are driven by a multiplexer whose inputs are a
product term from the CPLD AND Array or the
MCU Address Strobe (ALE/AS). Each product
term output is used to latch or clock four Input
Macrocells (IMC). Port inputs 3-0 can be controlled by one product term and 7-4 by another.
Configurations for the Input Macrocells (IMC) are
specified by equations written in PSDabel (see Application Note AN1171). Outputs of the Input Macrocells (IMC) can be read by the MCU via the IMC
buffer.
See
the
section
entitled
I/O
PORTS, page 51.
Input Macrocells (IMC) can use Address Strobe
(ALE/AS, PD0) to latch address bits higher than
A15. Any latched addresses are routed to the
PLDs as inputs.
Input Macrocells (IMC) are particularly useful with
handshaking communication applications where
two processors pass data back and forth through
a common mailbox. Figure 18., page 42 shows a
typical configuration where the Master MCU writes
to the Port A Data Out Register. This, in turn, can
be read by the Slave MCU via the activation of the
“Slave-Read” output enable product term.
The Slave can also write to the Port A Input Macrocells (IMC) and the Master can then read the Input Macrocells (IMC) directly.
Note that the “Slave-Read” and “Slave-Wr” signals
are product terms that are derived from the Slave
MCU inputs Read Strobe (RD, CNTL1), Write
Strobe (WR, CNTL0), and Slave_CS.
c
u
d
e
t
le
)
s
(
ct
o
s
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
40/109
Doc ID 10552 Rev 3
o
r
P
)
s
t(
r
P
e
s
b
O
t
e
l
o
PLD INPUT BUS
ENABLE ( .OE )
u
d
o
AND ARRAY
)
s
(
ct
MUX
OUTPUT
MACROCELLS BC
AND
MACROCELL AB
o
s
b
O
-
Doc ID 10552 Rev 3
FEEDBACK
PT
PT
Q
D FF
Q
D
D
INPUT MACROCELL _ RD
e
t
le
G
o
r
P
LATCH
ALE/AS
DIRECTION
REGISTER
D [ 7:0]
INPUT MACROCELL
MUX
PT
INTERNAL DATA BUS
PORT
DRIVER
AI02876B
I/O PIN
PSD813F2V, PSD854F2V
Figure 17. Input Macrocell
c
u
d
)
s
t(
41/109
u
d
o
s
b
O
t
e
l
o
42/109
)
s
(
ct
Doc ID 10552 Rev 3
D [ 7:0]
MCU - WR
MCU - RD
r
P
e
MASTER
MCU
PSD
CPLD
o
s
b
O
e
t
le
MCU -RD
D
Q
Q
D
PORT A
INPUT
MACROCELL
SLAVE– WR
MCU -WR
PORT A
DATA OUT
REGISTER
SLAVE – READ
WR
RD
SLAVE – CS
PORT A
D [ 7:0]
AI02877C
SLAVE
MCU
PSD813F2V, PSD854F2V
Figure 18. Handshaking Communication Using Input Macrocells
c
u
d
o
r
P
)
s
t(
PSD813F2V, PSD854F2V
MCU BUS INTERFACE
The “no-glue logic” MCU Bus Interface block can
be directly connected to most popular MCUs and
their control signals. Key 8-bit MCUs, with their
bus types and control signals, are shown in Table
16. The interface type is specified using the PSDsoft Express Configuration.
Table 16. MCUs and their Control Signals
Data Bus
Width
CNTL0
CNTL1
CNTL2
8031
8
WR
RD
PSEN
80C51XA
8
WR
RD
PSEN
80C251
8
WR
80C251
8
80198
MCU
PD02
PC7
ADIO0
PA3-PA0
PA7-PA3
(Note 1) ALE
A0
(Note 1)
(Note 1)
(Note 1) ALE
A4
A3-A0
(Note 1)
PSEN
(Note 1) (Note 1) ALE
A0
(Note 1)
(Note 1)
WR
RD
PSEN
(Note 1) ALE
A0
(Note 1)
(Note 1)
8
WR
RD
(Note 1) (Note 1) ALE
A0
(Note 1)
(Note 1)
68HC11
8
R/W
E
(Note 1) (Note 1) AS
A0
(Note 1)
68HC912
8
R/W
E
(Note 1) DBE
A0
(Note 1)
Z80
8
WR
RD
(Note 1) (Note 1) (Note 1) A0
Z8
8
R/W
DS
(Note 1) (Note 1) AS
68330
8
R/W
DS
(Note 1) (Note 1) AS
M37702M2
8
R/W
E
(Note 1) (Note 1) ALE
AS
e
t
le
o
r
P
c
u
d
D3-D0
)
s
t(
(Note 1)
(Note 1)
D7-D4
(Note 1)
(Note 1)
A0
(Note 1)
(Note 1)
A0
D3-D0
D7-D4
A0
Note: 1. Unused CNTL2 pin can be configured as CPLD input. Other unused pins (PC7, PD0, PA3-0) can be configured for other I/O functions.
2. ALE/AS input is optional for MCUs with a non-multiplexed bus
)
s
(
ct
o
s
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
43/109
PSD813F2V, PSD854F2V
PSD Interface to a Multiplexed 8-Bit Bus
Figure 19 shows an example of a system using a
MCU with an 8-bit multiplexed bus and a PSD. The
ADIO port on the PSD is connected directly to the
MCU address/data bus. Address Strobe (ALE/AS,
PD0) latches the address signals internally.
Latched addresses can be brought out to Port A or
B. The PSD drives the ADIO data bus only when
one of its internal resources is accessed and Read
Strobe (RD, CNTL1) is active. Should the system
address bus exceed sixteen bits, Ports A, B, C, or
D may be used as additional address inputs.
Figure 19. An Example of a Typical 8-bit Multiplexed Bus Interface
PSD
MCU
AD [ 7:0]
ADIO
PORT
A[ 15:8]
A [ 7: 0]
PORT
A
(OPTIONAL)
WR
WR (CNTRL0)
RD
RD (CNTRL1)
BHE (CNTRL2)
BHE
RST
e
t
le
ALE
ALE (PD0)
)
s
t(
A [ 15: 8]
PORT
B
c
u
d
(OPTIONAL)
o
r
P
PORT
C
PORT D
RESET
)
s
(
ct
o
s
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
44/109
Doc ID 10552 Rev 3
AI02878C
PSD813F2V, PSD854F2V
PSD Interface to a Non-Multiplexed 8-Bit Bus
Figure 20 shows an example of a system using a
MCU with an 8-bit non-multiplexed bus and a
PSD. The address bus is connected to the ADIO
Port, and the data bus is connected to Port A. Port
A is in tri-state mode when the PSD is not accessed by the MCU. Should the system address
bus exceed sixteen bits, Ports B, C, or D may be
used for additional address inputs.
Data Byte Enable Reference
MCUs have different data byte orientations. Table
17 shows how the PSD interprets byte/word operations in different bus WRITE configurations.
Even-byte refers to locations with address A0
equal to '0' and odd byte as locations with A0 equal
to ’1.’
MCU Bus Interface Examples
Figure 21 through 25 show examples of the basic
connections between the PSD and some popular
MCUs. The PSD Control input pins are labeled as
to the MCU function for which they are configured.
The MCU bus interface is specified using the PSDsoft Express Configuration.
Table 17. Eight-Bit Data Bus
BHE
A0
D7-D0
X
0
Even Byte
X
1
Odd Byte
Figure 20. An Example of a Typical 8-bit Non-Multiplexed Bus Interface
PSD
MCU
D [ 7:0]
PORT
A
ADIO
PORT
e
t
le
A [ 15:0]
so
WR (CNTRL0)
WR
RD
o
r
P
D [ 7:0]
A[ 23:16]
(OPTIONAL)
RD (CNTRL1)
BHE (CNTRL2)
BHE
)
s
(
ct
ALE
RESET
b
O
-
PORT
B
c
u
d
)
s
t(
u
d
o
RST
PORT
C
ALE (PD0)
PORT D
r
P
e
AI02879C
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
45/109
PSD813F2V, PSD854F2V
80C31
Figure 21 shows the bus interface for the 80C31,
which has an 8-bit multiplexed address/data bus.
The lower address byte is multiplexed with the
data bus. The MCU control signals Program Select Enable (PSEN, CNTL2), Read Strobe (RD,
CNTL1), and Write Strobe (WR, CNTL0) may be
used for accessing the internal memory and I/O
Ports blocks. Address Strobe (ALE/AS, PD0)
latches the address.
Figure 21. Interfacing the PSD with an 80C31
AD7-AD0
PSD
80C31
31
19
18
9
RESET
12
13
14
15
EA/VP
X1
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
X2
RESET
INT0
INT1
T0
T1
1
2
3
4
5
6
7
8
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
RD
WR
PSEN
ALE/P
TXD
RXD
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
30
31
32
33
34
35
36
37
39
38
37
36
35
34
33
32
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
21
22
23
24
25
26
27
28
A8
A9
A10
A11
A12
A13
A14
A15
39
40
41
42
43
44
45
46
17
RD
WR
47
16
29
30
50
49
11
10
so
RESET
)
s
(
ct
ADIO0
ADIO1
ADIO2
ADIO3
ADIO4
ADIO5
ADIO6
ADIO7
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
ADIO8
ADIO9
ADIO10
ADIO11
ADIO12
ADIO13
ADIO14
ADIO15
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
10
9
8
48
CNTL1(RD)
CNTL2 (PSEN)
PD0-ALE
PD1
PD2
29
28
27
25
24
23
22
21
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
)
s
t(
7
6
5
4
3
2
52
51
c
u
d
o
r
P
CNTL0 (WR)
e
t
le
PSEN
ALE
RESET
46/109
AD[ 7:0 ]
20
19
18
17
14
13
12
11
RESET
AI02880C
PSD813F2V, PSD854F2V
80C251
The Intel 80C251 MCU features a user-configurable bus interface with four possible bus configurations, as shown in Table 18., page 48.
The first configuration is 80C31-compatible, and
the bus interface to the PSD is identical to that
shown in Figure 21., page 46. The second and
third configurations have the same bus connection
as shown in Figure 22. There is only one Read
Strobe (PSEN) connected to CNTL1 on the PSD.
The A16 connection to PA0 allows for a larger address input to the PSD. The fourth configuration is
shown in Figure 23., page 48. Read Strobe (RD) is
connected to CNTL1 and Program Select Enable
(PSEN) is connected to CNTL2.
The 80C251 has two major operating modes:
Page mode and Non-page mode. In Non-page
mode, the data is multiplexed with the lower address byte, and Address Strobe (ALE/AS, PD0) is
active in every bus cycle. In Page mode, data (D7D0) is multiplexed with address (A15-A8). In a bus
cycle where there is a Page hit, Address Strobe
(ALE/AS, PD0) is not active and only addresses
(A7-A0) are changing. The PSD supports both
modes. In Page Mode, the PSD bus timing is identical to Non-Page Mode except the address hold
time and setup time with respect to Address
Strobe (ALE/AS, PD0) is not required. The PSD
access time is measured from address (A7-A0)
valid to data in valid.
Figure 22. Interfacing the PSD with the 80C251, with One READ Input
2
3
4
5
6
7
8
9
21
20
11
13
14
15
16
17
10
RESET
35
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
X1
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
X2
P3.0/RXD
P3.1/TXD
P3.2/INT0
P3.3/INT1
P3.4/T0
P3.5/T1
RST
EA
ALE
PSEN
43
42
41
40
39
38
37
36
A0
A1
A2
A3
A4
A5
A6
A7
24
25
26
27
28
29
30
31
AD8
AD9
AD10
AD11
AD12
AD13
AD14
AD15
33
32
c
u
d
WR
RD/A16
o
r
P
e
t
e
l
o
RESET
c
u
d
PSD
80C251SB
18
19
(t s)
ALE
A0
A1
A2
A3
A4
A5
A6
A7
b
O
-
RD
39
40
41
42
43
44
45
46
47
50
WR
A16
49
10
9
8
RESET
ADIO0
ADIO1
ADIO2
ADIO3
ADIO4
ADIO5
ADIO6
ADIO7
e
t
le
so
AD8
AD9
AD10
AD11
AD12
AD13
AD14
AD15
30
31
32
33
34
35
36
37
48
o
r
P
ADIO8
ADIO9
ADIO10
ADIO11
ADIO12
ADIO13
ADIO14
ADIO15
CNTL0 ( WR)
CNTL1( RD)
CNTL 2(PSEN)
PD0-ALE
PD1
PD2
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
)
s
t(
29
28
27
25
24
23
22
21
A161
A171
7
6
5
4
3
2
52
51
20
19
18
17
14
13
12
11
RESET
AI02881C
s
b
O
Note: 1. The A16 and A17 connections are optional.
2. In non-Page-Mode, AD7-AD0 connects to ADIO7-ADIO0.
Doc ID 10552 Rev 3
47/109
PSD813F2V, PSD854F2V
Figure 23. Interfacing the PSD with the 80C251, with RD and PSEN Inputs
80C251SB
2
3
4
5
6
7
8
9
21
20
11
13
14
15
16
17
RESET
10
35
PSD
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
X1
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
X2
P3.0/RXD
P3.1/TXD
P3.2/INT0
P3.3/INT1
P3.4/T0
P3.5/T1
ALE
PSEN
RST
WR
RD/A16
EA
43
42
41
40
39
38
37
36
A0
A1
A2
A3
A4
A5
A6
A7
24
25
26
27
28
29
30
31
AD8
AD9
AD10
AD11
AD12
AD13
AD14
AD15
A0
A1
A2
A3
A4
A5
A6
A7
30
31
32
33
34
35
36
37
AD8
AD9
AD10
AD11
AD12
AD13
AD14
AD15
39
40
41
42
43
44
45
46
33
ALE
47
32
RD
50
18
WR
19
PSEN
49
10
9
8
RESET
RESET
48
e
t
le
Table 18. 80C251 Configurations
o
s
b
O
-
ADIO0
ADIO1
ADIO2
ADIO3
ADIO4
ADIO5
ADIO6
ADIO7
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
ADIO8
ADIO9
ADIO10
ADIO11
ADIO12
ADIO13
ADIO14
ADIO15
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
CNTL0 ( WR)
CNTL1( RD)
CNTL 2(PSEN)
PD0-ALE
PD1
PD2
c
u
d
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
7
6
5
4
3
2
52
51
20
19
18
17
14
13
12
11
)
s
t(
o
r
P
RESET
29
28
27
25
24
23
22
21
AI02882C
Configuration
80C251 READ/WRITE
Pins
Connecting to PSD Pins
Page Mode
1
WR
RD
PSEN
CNTL0
CNTL1
CNTL2
Non-Page Mode, 80C31 compatible A7A0 multiplex with D7-D0
2
WR
PSEN only
CNTL0
CNTL1
Non-Page Mode
A7-A0 multiplex with D7-D0
3
WR
PSEN only
CNTL0
CNTL1
Page Mode
A15-A8 multiplex with D7-D0
WR
RD
PSEN
CNTL0
CNTL1
CNTL2
Page Mode
A15-A8 multiplex with D7-D0
r
P
e
t
e
l
o
4
u
d
o
)
s
(
ct
s
b
O
48/109
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
80C51XA
The Philips 80C51XA MCU family supports an 8or 16-bit multiplexed bus that can have burst cycles. Address bits (A3-A0) are not multiplexed,
while (A19-A4) are multiplexed with data bits
(D15-D0) in 16-bit mode. In 8-bit mode, (A11-A4)
are multiplexed with data bits (D7-D0).
The 80C51XA can be configured to operate in
eight-bit data mode (as shown in Figure 24).
The 80C51XA improves bus throughput and performance by executing burst cycles for code fetch-
es. In Burst Mode, address A19-A4 are latched
internally by the PSD, while the 80C51XA changes
the A3-A0 signals to fetch up to 16 bytes of code.
The PSD access time is then measured from address A3-A0 valid to data in valid. The PSD bus
timing requirement in Burst Mode is identical to the
normal bus cycle, except the address setup and
hold time with respect to Address Strobe (ALE/AS,
PD0) does not apply.
Figure 24. Interfacing the PSD with the 80C51X, 8-bit Data Bus
PSD
80C51XA
21
20
11
13
6
7
9
8
16
10
14
15
RESET
35
17
XTAL1
XTAL2
RXD0
TXD0
RXD1
TXD1
T2EX
T2
T0
RST
INT0
INT1
EA/WAIT
BUSW
A0/WRH
A1
A2
A3
A4D0
A5D1
A6D2
A7D3
A8D4
A9D5
A10D6
A11D7
A12D8
A13D9
A14D10
A15D11
A16D12
A17D13
A18D14
A19D15
PSEN
RD
WRL
A0
A1
A2
A3
A4D0
A5D1
A6D2
A7D3
A8D4
A9D5
A10D6
A11D7
A12
A13
A14
A15
A16
A17
A18
A19
2
3
4
5
43
42
41
40
39
38
37
36
24
25
26
27
28
29
30
31
PSEN
32
(s)
19
18
33
t
c
u
ALE
RD
WR
ALE
A4D0
A5D1
A6D2
A7D3
A8D4
A9D5
A10D6
A11D7
30
31
32
33
34
35
36
37
A12
A13
A14
A15
A16
A17
A18
A19
39
ADIO8
40
ADIO9
41
ADIO10
42
ADIO11
43
AD1012
44
AD1013
45
ADIO14
46
ADIO15
e
t
le
o
s
b
O
-
d
o
r
P
e
ADIO0
ADIO1
ADIO2
ADIO3
AD104
AD105
ADIO6
ADIO7
47
50
49
10
8
9
48
CNTL 2(PSEN)
PD0-ALE
PD1
PD2
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
)
s
t(
29
28
27
25
24
23
22
21
c
u
d
o
r
P
CNTL0 (WR)
CNTL1(RD)
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
A0
A1
A2
A3
7
6
5
4
3
2
52
51
20
19
18
17
14
13
12
11
RESET
RESET
AI02883C
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
49/109
PSD813F2V, PSD854F2V
68HC11
Figure 25 shows a bus interface to a 68HC11
where the PSD is configured in 8-bit multiplexed
mode with E and R/W settings. The DPLD can be
used to generate the READ and WR signals for
external devices.
Figure 25. Interfacing the PSD with a 68HC11
AD7-AD0
AD7-AD0
PSD
31
30
29
28
27
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
30
31
32
33
34
35
36
37
42
41
40
39
38
37
36
35
A8
A9
A10
A11
A12
A13
A14
A15
39
40
41
42
43
44
45
46
68HC11
8
7
RESET
17
19
18
2
34
33
32
43
44
45
46
47
48
49
50
52
51
PA3
PA4
PA5
PA6
PA7
XT
EX
RESET
IRQ
XIRQ
MODB
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PA0
PA1
PA2
9
10
11
12
13
14
15
16
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
PE0
PE1
PE2
PE3
PE4
PE5
PE6
PE7
20
21
22
23
24
25
PD0
PD1
PD2
PD3
PD4
PD5
VRH
VRL
(t s)
3
MODA
E
AS
uc
R/W
od
r
P
e
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
E
4
AS
6
R/W
ADIO8
ADIO9
ADIO10
ADIO11
AD1012
AD1013
ADIO14
ADIO15
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
ro
49
10
9
8
48
c
u
d
CNTL0 (R _W)
CNTL1(E)
CNTL 2
PD0 – AS
PD1
PD2
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
29
28
27
25
24
23
22
21
7
6
5
4
3
2
52
51
)
s
t(
20
19
18
17
14
13
12
11
RESET
RESET
AI02884C
t
e
l
o
s
b
O
50/109
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
P
e
let
o
s
b
O
-
5
47
50
ADIO0
ADIO1
ADIO2
ADIO3
AD104
AD105
ADIO6
ADIO7
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
I/O PORTS
There are four programmable I/O ports: Ports A, B,
C, and D. Each of the ports is eight bits except Port
D, which is 3 bits. Each port pin is individually user
configurable, thus allowing multiple functions per
port. The ports are configured using PSDsoft Express Configuration or by the MCU writing to onchip registers in the CSIOP space.
The topics discussed in this section are:
■
General Port architecture
■
Port operating modes
■
Port Configuration Registers (PCR)
■
Port Data Registers
■
Individual Port functionality.
General Port Architecture
The general architecture of the I/O Port block is
shown in Figure 26., page 52. Individual Port architectures are shown in Figure 28., page 58 to
Figure 31., page 61. In general, once the purpose
for a port pin has been defined, that pin is no longer available for other purposes. Exceptions are
noted.
As shown in Figure 26., page 52, the ports contain
an output multiplexer whose select signals are
driven by the configuration bits in the Control Registers (Ports A and B only) and PSDsoft Express
Configuration. Inputs to the multiplexer include the
following:
■
Output data from the Data Out register
■
Latched address outputs
■
CPLD macrocell output
■
External Chip Select (ECS0-ECS2) from the
CPLD.
The Port Data Buffer (PDB) is a tri-state buffer that
allows only one source at a time to be read. The
Port Data Buffer (PDB) is connected to the Internal
Data Bus for feedback and can be read by the
MCU. The Data Out and macrocell outputs, Direction and Control Registers, and port pin input are
all connected to the Port Data Buffer (PDB).
)
s
(
ct
u
d
o
r
P
e
t
e
l
o
The Port pin’s tri-state output driver enable is controlled by a two input OR gate whose inputs come
from the CPLD AND Array enable product term
and the Direction Register. If the enable product
term of any of the Array outputs are not defined
and that port pin is not defined as a CPLD output
in the PSDabel file, then the Direction Register has
sole control of the buffer that drives the port pin.
The contents of these registers can be altered by
the MCU. The Port Data Buffer (PDB) feedback
path allows the MCU to check the contents of the
registers.
Ports A, B, and C have embedded Input Macrocells (IMC). The Input Macrocells (IMC) can be
configured as latches, registers, or direct inputs to
the PLDs. The latches and registers are clocked
by Address Strobe (ALE/AS, PD0) or a product
term from the PLD AND Array. The outputs from
the Input Macrocells (IMC) drive the PLD input bus
and can be read by the MCU. See the section entitled Input Macrocell, page 41.
Port Operating Modes
The I/O Ports have several modes of operation.
Some modes can be defined using PSDabel,
some by the MCU writing to the Control Registers
in CSIOP space, and some by both. The modes
that can only be defined using PSDsoft Express
must be programmed into the device and cannot
be changed unless the device is reprogrammed.
The modes that can be changed by the MCU can
be done so dynamically at run-time. The PLD I/O,
Data Port, Address Input, and Peripheral I/O
modes are the only modes that must be defined
before programming the device. All other modes
can be changed by the MCU at run-time. See Application Note AN1171 for more detail.
Table 19., page 53 summarizes which modes are
available on each port. Table 22., page 56 shows
how and where the different modes are configured. Each of the port operating modes are described in the following sections.
c
u
d
e
t
le
)
s
t(
o
r
P
o
s
b
O
-
s
b
O
Doc ID 10552 Rev 3
51/109
PSD813F2V, PSD854F2V
Figure 26. General I/O Port Architecture
DATA OUT
REG.
D
Q
D
Q
DATA OUT
WR
ADDRESS
ALE
ADDRESS
PORT PIN
OUTPUT
MUX
G
MACROCELL OUTPUTS
EXT CS
INTERNAL DATA BUS
READ MUX
P
OUTPUT
SELECT
D
DATA IN
B
CONTROL REG.
D
ENABLE OUT
Q
WR
c
u
d
DIR REG.
D
Q
WR
ENABLE PRODUCT TERM (.OE)
e
t
le
CPLD-INPUT
so
)
s
(
ct
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
52/109
Doc ID 10552 Rev 3
)
s
t(
o
r
P
INPUT
MACROCELL
AI02885
PSD813F2V, PSD854F2V
MCU I/O Mode
In the MCU I/O mode, the MCU uses the I/O Ports
block to expand its own I/O ports. By setting up the
CSIOP space, the ports on the PSD are mapped
into the MCU address space. The addresses of
the ports are listed in Table 7., page 18.
A port pin can be put into MCU I/O mode by writing
a 0 to the corresponding bit in the Control Register. The MCU I/O direction may be changed by
writing to the corresponding bit in the Direction
Register, or by the output enable product term.
See the section entitled Peripheral I/O
Mode, page 55. When the pin is configured as an
output, the content of the Data Out Register drives
the pin. When configured as an input, the MCU
can read the port input through the Data In buffer.
See Figure 26., page 52.
Ports C and D do not have Control Registers, and
are in MCU I/O mode by default. They can be used
for PLD I/O if equations are written for them in PSDabel.
PLD I/O Mode
The PLD I/O Mode uses a port as an input to the
CPLD’s Input Macrocells (IMC), and/or as an output from the CPLD’s Output Macrocells (OMC).
The output can be tri-stated with a control signal.
This output enable control signal can be defined
by a product term from the PLD, or by resetting the
Table 19. Port Operating Modes
Port Mode
Port A
MCU I/O
Yes
PLD I/O
McellAB Outputs
McellBC Outputs
Additional Ext. CS Outputs
PLD Inputs
Yes
No
No
Yes
corresponding bit in the Direction Register to ’0.’
The corresponding bit in the Direction Register
must not be set to '1' if the pin is defined for a PLD
input signal in PSDabel. The PLD I/O mode is
specified in PSDabel by declaring the port pins,
and then writing an equation assigning the PLD I/
O to a port.
Address Out Mode
For MCUs with a multiplexed address/data bus,
Address Out Mode can be used to drive latched
addresses on to the port pins. These port pins can,
in turn, drive external devices. Either the output
enable or the corresponding bits of both the Direction Register and Control Register must be set to
a 1 for pins to use Address Out Mode. This must
be done by the MCU at run-time. See Table 21 for
the address output pin assignments on Ports A
and B for various MCUs.
For non-multiplexed 8-bit bus mode, address signals (A7-A0) are available to Port B in Address Out
Mode.
Note: Do not drive address signals with Address
Out Mode to an external memory device if it is intended for the MCU to Boot from the external device. The MCU must first Boot from PSD memory
so the Direction and Control register bits can be
set.
c
u
d
e
t
le
o
s
b
O
Port B
o
r
P
Port C
Port D
Yes
Yes
Yes
Yes
No
Yes
No
Yes
No
Yes
No
No
Yes
Yes
Yes (A7 – 0)
Yes (A7 – 0)
or (A15 – 8)
No
No
Yes
Yes
Yes
Yes
Yes (D7 – 0)
No
No
No
Peripheral I/O
Yes
No
No
No
JTAG ISP
No
No
Yes1
No
t
e
l
o
Data Port
s
b
O
)
s
(
ct
u
d
o
r
P
e
Address Out
Address In
Yes
)
s
t(
Note: 1. Can be multiplexed with other I/O functions.
Doc ID 10552 Rev 3
53/109
PSD813F2V, PSD854F2V
Table 20. Port Operating Mode Settings
Defined in
PSDabel
Mode
Defined in PSD
Configuration
Control
Register
Setting
Direction
Register
Setting
VM
Register
Setting
JTAG Enable
MCU I/O
Declare pins only
N/A1
0
1 = output,
0 = input
N/A
(Note 2)
N/A
PLD I/O
Logic equations
N/A
N/A
(Note 2)
N/A
N/A
Data Port (Port A)
N/A
Specify bus type
N/A
N/A
N/A
N/A
Address Out
(Port A,B)
Declare pins only
N/A
1
1 (Note 2)
N/A
N/A
Address In
(Port A,B,C,D)
Logic for equation
Input Macrocells
N/A
N/A
N/A
N/A
N/A
Peripheral I/O
(Port A)
Logic equations
(PSEL0 & 1)
N/A
N/A
N/A
PIO bit = 1 N/A
JTAG ISP (Note 3)
JTAGSEL
JTAG
Configuration
N/A
N/A
N/A
)
s
t(
JTAG_Enable
c
u
d
Note: 1. N/A = Not Applicable
2. The direction of the Port A,B,C, and D pins are controlled by the Direction Register ORed with the individual output enable product
term (.oe) from the CPLD AND Array.
3. Any of these three methods enables the JTAG pins on Port C.
Table 21. I/O Port Latched Address Output Assignments
MCU
Port A (PA3-PA0)
8051XA (8-Bit)
N/A1
Address a7-a4
80C251
(Page Mode)
N/A
N/A
All Other
8-Bit Multiplexed
Address a3-a0
8-Bit
Non-Multiplexed Bus
N/A
so
Port B (PB7-PB4)
N/A
Address a11-a8
Address a15-a12
Address a7-a4
Address a3-a0
Address a7-a4
N/A
Address a3-a0
Address a7-a4
)
s
(
ct
b
O
-
r
P
e
t
e
l
o
s
b
O
54/109
Port B (PB3-PB0)
Address a11-a8
u
d
o
Note: 1. N/A = Not Applicable.
e
t
le
Port A (PA7-PA4)
o
r
P
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
Address In Mode
For MCUs that have more than 16 address signals, the higher addresses can be connected to
Port A, B, C, and D. The address input can be
latched in the Input Macrocell (IMC) by Address
Strobe (ALE/AS, PD0). Any input that is included
in the DPLD equations for the SRAM, or primary or
secondary Flash memory is considered to be an
address input.
Data Port Mode
Port A can be used as a data bus port for a MCU
with a non-multiplexed address/data bus. The
Data Port is connected to the data bus of the MCU.
The general I/O functions are disabled in Port A if
the port is configured as a Data Port.
Peripheral I/O Mode
Peripheral I/O mode can be used to interface with
external peripherals. In this mode, all of Port A
serves as a tri-state, bi-directional data buffer for
the MCU. Peripheral I/O Mode is enabled by setting Bit 7 of the VM Register to a ’1.’ Figure 27
shows how Port A acts as a bi-directional buffer for
the MCU data bus if Peripheral I/O Mode is enabled. An equation for PSEL0 and/or PSEL1 must
be written in PSDabel. The buffer is tri-stated
when PSEL0 or PSEL1 is not active.
Figure 27. Peripheral I/O Mode
RD
c
u
d
PSEL0
PSEL
PSEL1
D0 - D7
DATA BUS
VM REGISTER BIT 7
WR
)
s
(
ct
o
s
b
O
-
e
t
le
)
s
t(
o
r
P
PA0 - PA7
AI02886
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
55/109
PSD813F2V, PSD854F2V
JTAG In-System Programming (ISP)
Port C is JTAG compliant, and can be used for InSystem Programming (ISP). You can multiplex
JTAG operations with other functions on Port C
because In-System Programming (ISP) is not performed in normal Operating mode. For more information on the JTAG Port, see the section entitled
PROGRAMMING IN-CIRCUIT USING THE JTAG
SERIAL INTERFACE, page 69.
Port Configuration Registers (PCR)
Each Port has a set of Port Configuration Registers (PCR) used for configuration. The contents of
the registers can be accessed by the MCU through
normal READ/WRITE bus cycles at the addresses
given in Table 7., page 18. The addresses in Table 7 are the offsets in hexadecimal from the base
of the CSIOP register.
The pins of a port are individually configurable and
each bit in the register controls its respective pin.
For example, Bit 0 in a register refers to Bit 0 of its
port. The three Port Configuration Registers
(PCR), shown in Table 22, are used for setting the
Port configurations. The default Power-up state for
each register in Table 22 is 00h.
Control Register
Any bit reset to '0' in the Control Register sets the
corresponding port pin to MCU I/O Mode, and a '1'
sets it to Address Out Mode. The default mode is
MCU I/O. Only Ports A and B have an associated
Control Register.
Direction Register
The Direction Register, in conjunction with the output enable (except for Port D), controls the direction of data flow in the I/O Ports. Any bit set to '1'
in the Direction Register causes the corresponding pin to be an output, and any bit set to '0' causes
it to be an input. The default mode for all port pins
is input.
Figure 28., page 58 and Figure 29., page 59 show
the Port Architecture diagrams for Ports A/B and
C, respectively. The direction of data flow for Ports
A, B, and C are controlled not only by the direction
register, but also by the output enable product
term from the PLD AND Array. If the output enable
product term is not active, the Direction Register
has sole control of a given pin’s direction.
An example of a configuration for a Port with the
three least significant bits set to output and the remainder set to input is shown in Table 25. Since
Port D only contains three pins (shown in Figure
31., page 61), the Direction Register for Port D
has only the three least significant bits active.
o
r
P
e
t
e
l
o
bs
O
56/109
c
u
d
(t s)
Drive Select Register
The Drive Select Register configures the pin driver
as Open Drain or CMOS for some port pins, and
controls the slew rate for the other port pins. An
external pull-up resistor should be used for pins
configured as Open Drain.
A pin can be configured as Open Drain if its corresponding bit in the Drive Select Register is set to a
’1.’ The default pin drive is CMOS.
Note that the slew rate is a measurement of the
rise and fall times of an output. A higher slew rate
means a faster output response and may create
more electrical noise. A pin operates in a high slew
rate when the corresponding bit in the Drive Register is set to ’1.’ The default rate is slow slew.
Table 26., page 57 shows the Drive Register for
Ports A, B, C, and D. It summarizes which pins can
be configured as Open Drain outputs and which
pins the slew rate can be set for.
c
u
d
)
s
t(
Table 22. Port Configuration Registers (PCR)
Register Name
Control
Port
ro
A,B
P
e
let
Direction
A,B,C,D
Drive Select1
MCU Access
WRITE/READ
WRITE/READ
A,B,C,D
WRITE/READ
Note: 1. See Table 26., page 57 for Drive Register bit definition.
o
s
b
O
-
Table 23. Port Pin Direction Control, Output
Enable P.T. Not Defined
Direction Register Bit
Port Pin Mode
0
Input
1
Output
Table 24. Port Pin Direction Control, Output
Enable P.T. Defined
Direction
Register Bit
Output Enable
P.T.
Port Pin Mode
0
0
Input
0
1
Output
1
0
Output
1
1
Output
Table 25. Port Direction Assignment Example
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
0
0
0
1
1
1
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
Table 26. Drive Register Pin Assignment
Drive
Register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Port A
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Slew
Rate
Slew
Rate
Slew
Rate
Slew
Rate
Port B
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Slew
Rate
Slew
Rate
Slew
Rate
Slew
Rate
Port C
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Port D
NA1
NA1
NA1
NA1
NA1
Slew
Rate
Slew
Rate
Slew
Rate
Note: 1. NA = Not Applicable.
Port Data Registers
The Port Data Registers, shown in Table 27, are
used by the MCU to write data to or read data from
the ports. Table 27 shows the register name, the
ports having each register type, and MCU access
for each register type. The registers are described
below.
Data In
Port pins are connected directly to the Data In buffer. In MCU I/O input mode, the pin input is read
through the Data In buffer.
Data Out Register
Stores output data written by the MCU in the MCU
I/O output mode. The contents of the Register are
driven out to the pins if the Direction Register or
the output enable product term is set to ’1.’ The
contents of the register can also be read back by
the MCU.
)
s
(
ct
Table 27. Port Data Registers
Register Name
u
d
o
Data In
Output Macrocells (OMC). The CPLD Output
Macrocells (OMC) occupy a location in the MCU’s
address space. The MCU can read the output of
the Output Macrocells (OMC). If the OMC Mask
Register bits are not set, writing to the macrocell
loads data to the macrocell flip-flops. See the section entitled PLDS, page 33.
OMC Mask Register
Each OMC Mask Register bit corresponds to an
Output Macrocell (OMC) flip-flop. When the OMC
Mask Register bit is set to a 1, loading data into the
Output Macrocell (OMC) flip-flop is blocked. The
default value is 0 or unblocked.
c
u
d
e
t
le
o
r
P
o
s
b
O
-
Port
MCU Access
A,B,C,D
READ – input on pin
A,B,C,D
WRITE/READ
A,B,C
READ – outputs of macrocells
WRITE – loading macrocells flip-flop
A,B,C
WRITE/READ – prevents loading into a given
macrocell
Input Macrocell
A,B,C
READ – outputs of the Input Macrocells
Enable Out
A,B,C
READ – the output enable control of the port driver
r
P
e
Data Out
Output Macrocell
t
e
l
o
Mask Macrocell
s
b
O
)
s
t(
Doc ID 10552 Rev 3
57/109
PSD813F2V, PSD854F2V
Input Macrocells (IMC)
The Input Macrocells (IMC) can be used to latch or
store external inputs. The outputs of the Input
Macrocells (IMC) are routed to the PLD input bus,
and can be read by the MCU. See the section entitled PLDS, page 33.
Enable Out
The Enable Out register can be read by the MCU.
It contains the output enable values for a given
port. A 1 indicates the driver is in output mode. A
0 indicates the driver is in tri-state and the pin is in
input mode.
Ports A and B – Functionality and Structure
Ports A and B have similar functionality and structure, as shown in Figure 28. The two ports can be
configured to perform one or more of the following
functions:
■
MCU I/O Mode
■
CPLD Output – Macrocells McellAB7McellAB0 can be connected to Port A or Port
B. McellBC7-McellBC0 can be connected to
Port B or Port C.
■
CPLD Input – Via the Input Macrocells (IMC).
■
Latched Address output – Provide latched
address output as per Table 21., page 54.
■
Address In – Additional high address inputs
using the Input Macrocells (IMC).
■
Open Drain/Slew Rate – pins PA3-PA0 and
PB3-PB0 can be configured to fast slew rate,
pins PA7-PA4 and PB7-PB4 can be
configured to Open Drain Mode.
■
Data Port – Port A to D7-D0 for 8 bit nonmultiplexed bus
■
Multiplexed Address/Data port for certain
types of MCU bus interfaces.
■
Peripheral Mode – Port A only
c
u
d
e
t
le
Figure 28. Port A and Port B Structure
DATA OUT
REG.
D
Q
D
Q
ALE
)
s
(
ct
G
INTERNAL DATA BUS
MACROCELL OUTPUTS
O
u
d
o
PORT
A OR B PIN
ADDRESS
A[ 7:0] OR A[15:8]
OUTPUT
MUX
READ MUX
r
P
e
t
e
l
o
bs
o
r
P
DATA OUT
WR
ADDRESS
o
s
b
O
-
)
s
t(
P
OUTPUT
SELECT
D
DATA IN
B
CONTROL REG.
D
ENABLE OUT
Q
WR
DIR REG.
D
Q
WR
ENABLE PRODUCT TERM (.OE)
INPUT
MACROCELL
CPLD - INPUT
AI02887
58/109
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
Port C – Functionality and Structure
Port C can be configured to perform one or more
of the following functions (see Figure 29):
■
MCU I/O Mode
■
CPLD Output – McellBC7-McellBC0 outputs
can be connected to Port B or Port C.
■
CPLD Input – via the Input Macrocells (IMC)
■
Address In – Additional high address inputs
using the Input Macrocells (IMC).
■
In-System Programming (ISP) – JTAG port
can be enabled for programming/erase of the
PSD device. (See the section entitled
PROGRAMMING IN-CIRCUIT USING THE
JTAG SERIAL INTERFACE, page 69 for
more information on JTAG programming.)
■
Open Drain – Port C pins can be configured in
Open Drain Mode
Port C does not support Address Out mode, and
therefore no Control Register is required.
Pin PC7 may be configured as the DBE input in
certain MCU bus interfaces.
Figure 29. Port C Structure
DATA OUT
REG.
D
DATA OUT
Q
WR
1
SPECIAL FUNCTION
c
u
d
MCELLBC[ 7:0]
INTERNAL DATA BUS
READ MUX
P
OUTPUT
SELECT
D
)
s
t(
PORT C PIN
OUTPUT
MUX
DATA IN
e
t
le
B
o
r
P
ENABLE OUT
DIR REG.
D
Q
WR
ENABLE PRODUCT TERM (.OE)
(s)
o
s
b
O
-
t
c
u
CPLD-INPUT
d
o
r
P
e
INPUT
MACROCELL
SPECIAL FUNCTION
CONFIGURATION
AI02888B
BIT
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
59/109
PSD813F2V, PSD854F2V
Port D – Functionality and Structure
Port D has three I/O pins. See Figure 30 and Figure 31., page 61. This port does not support Address Out mode, and therefore no Control
Register is required. Port D can be configured to
perform one or more of the following functions:
■
MCU I/O Mode
■
CPLD Output – External Chip Select (ECS0ECS2)
■
CPLD Input – direct input to the CPLD, no
Input Macrocells (IMC)
Slew rate – pins can be set up for fast slew
rate
Port D pins can be configured in PSDsoft Express
as input pins for other dedicated functions:
■
Address Strobe (ALE/AS, PD0)
■
CLKIN (PD1) as input to the macrocells flipflops and APD counter
■
PSD Chip Select Input (CSI, PD2). Driving this
signal High disables the Flash memory, SRAM
and CSIOP.
■
Figure 30. Port D Structure
DATA OUT
REG.
DATA OUT
D
Q
WR
PORT D PIN
OUTPUT
MUX
c
u
d
ECS[ 2:0]
INTERNAL DATA BUS
READ MUX
OUTPUT
SELECT
P
DATA IN
B
DIR REG.
D
Q
(s)
WR
o
s
b
O
-
CPLD-INPUT
t
c
u
d
o
r
P
e
t
e
l
o
s
b
O
60/109
e
t
le
D
Doc ID 10552 Rev 3
o
r
P
ENABLE PRODUCT
TERM (.OE)
AI02889
)
s
t(
PSD813F2V, PSD854F2V
External Chip Select
The CPLD also provides three External Chip Select (ECS0-ECS2) outputs on Port D pins that can
be used to select external devices. Each External
Chip Select (ECS0-ECS2) consists of one product
term that can be configured active High or Low.
The output enable of the pin is controlled by either
the output enable product term or the Direction
Register. (See Figure 31.)
Figure 31. Port D External Chip Select Signals
ENABLE (.OE)
CPLD AND ARRAY
PLD INPUT BUS
PT0
DIRECTION
REGISTER
PD0 PIN
ECS0
POLARITY
BIT
ENABLE (.OE)
PT1
DIRECTION
REGISTER
POLARITY
BIT
e
t
le
ENABLE (.OE)
PT2
DIRECTION
REGISTER
o
s
b
O
-
ECS2
POLARITY
BIT
)
s
(
ct
c
u
d
PD1 PIN
ECS1
)
s
t(
o
r
P
PD2 PIN
AI02890
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
61/109
PSD813F2V, PSD854F2V
POWER MANAGEMENT
All PSD devices offer configurable power saving
options. These options may be used individually or
in combinations, as follows:
■
All memory blocks in a PSD (primary and
secondary Flash memory, and SRAM) are
built with power management technology. In
addition to using special silicon design
methodology, power management technology
puts the memories into standby mode when
address/data inputs are not changing (zero
DC current). As soon as a transition occurs on
an input, the affected memory “wakes up”,
changes and latches its outputs, then goes
back to standby. The designer does not have
to do anything special to achieve memory
standby mode when no inputs are changing—
it happens automatically.
The PLD sections can also achieve standby
mode when its inputs are not changing, as
described in the sections on the Power
Management Mode Registers (PMMR).
■
As with the Power Management mode, the
Automatic Power Down (APD) block allows
the PSD to reduce to standby current
automatically. The APD Unit can also block
MCU address/data signals from reaching the
memories and PLDs. This feature is available
on all the devices of the PSD family. The APD
Unit is described in more detail in the sections
entitled Automatic Power-down (APD) Unit
and Power-down Mode, page 63.
Built in logic monitors the Address Strobe of the
MCU for activity. If there is no activity for a
certain time period (MCU is asleep), the APD
Unit initiates Power-down mode (if enabled).
Once in Power-down mode, all address/data
signals are blocked from reaching PSD memory
and PLDs, and the memories are deselected
internally. This allows the memory and PLDs to
)
s
(
ct
u
d
o
■
■
remain in standby mode even if the address/
data signals are changing state externally
(noise, other devices on the MCU bus, etc.).
Keep in mind that any unblocked PLD input
signals that are changing states keeps the PLD
out of standby mode, but not the memories.
PSD Chip Select Input (CSI, PD2) can be
used to disable the internal memories, placing
them in standby mode even if inputs are
changing. This feature does not block any
internal signals or disable the PLDs. This is a
good alternative to using the APD Unit. There
is a slight penalty in memory access time
when PSD Chip Select Input (CSI, PD2)
makes its initial transition from deselected to
selected.
The PMMRs can be written by the MCU at runtime to manage power. All PSD supports
“blocking bits” in these registers that are set to
block designated signals from reaching both
PLDs. Current consumption of the PLDs is
directly related to the composite frequency of
the changes on their inputs (see Figure 35 and
Figure 36., page 72). Significant power
savings can be achieved by blocking signals
that are not used in DPLD or CPLD logic
equations.
PSD devices have a Turbo Bit in PMMR0. This
bit can be set to turn the Turbo mode off (the
default is with Turbo mode turned on). While
Turbo mode is off, the PLDs can achieve
standby current when no PLD inputs are
changing (zero DC current). Even when inputs
do change, significant power can be saved at
lower frequencies (AC current), compared to
when Turbo mode is on. When the Turbo mode
is on, there is a significant DC current
component and the AC component is higher.
e
t
le
o
s
b
O
-
r
P
e
t
e
l
o
s
b
O
62/109
c
u
d
Doc ID 10552 Rev 3
o
r
P
)
s
t(
PSD813F2V, PSD854F2V
Automatic Power-down (APD) Unit and Power-down Mode
The APD Unit, shown in Figure 32, puts the PSD
registers. The blocked signals include MCU
into Power-down mode by monitoring the activity
control signals and the common CLKIN (PD1).
of Address Strobe (ALE/AS, PD0). If the APD Unit
Note that blocking CLKIN (PD1) from the
is enabled, as soon as activity on Address Strobe
PLDs does not block CLKIN (PD1) from the
(ALE/AS, PD0) stops, a four bit counter starts
APD Unit.
counting. If Address Strobe (ALE/AS, PD0) re– All PSD memories enter standby mode and
mains inactive for fifteen clock periods of CLKIN
are drawing standby current. However, the
(PD1), Power-down (PDN) goes High, and the
PLD and I/O ports blocks do not go into
PSD enters Power-down mode, as discussed
standby Mode because you don’t want to have
next.
to wait for the logic and I/O to “wake-up”
Power-down Mode. By default, if you enable the
before their outputs can change. See Table 28
APD Unit, Power-down mode is automatically enfor Power-down mode effects on PSD ports.
abled. The device enters Power-down mode if Ad– Typical standby current is of the order of
dress Strobe (ALE/AS, PD0) remains inactive for
microamperes. These standby current values
fifteen periods of CLKIN (PD1).
assume that there are no transitions on any
The following should be kept in mind when the
PLD input.
PSD is in Power-down mode:
– If Address Strobe (ALE/AS, PD0) starts
Table 28. Power-down Mode’s Effect on Ports
pulsing again, the PSD returns to normal
Port Function
Pin Level
Operating mode. The PSD also returns to
normal Operating mode if either PSD Chip
MCU I/O
No Change
Select Input (CSI, PD2) is Low or the Reset
PLD Out
No Change
(RESET) input is High.
– The MCU address/data bus is blocked from all
Address Out
Undefined
memory and PLDs.
Data Port
Tri-State
– Various signals can be blocked (prior to
Power-down mode) from entering the PLDs by
Peripheral I/O
Tri-State
setting the appropriate bits in the PMMR
c
u
d
e
t
le
Figure 32. APD Unit
APD EN
PMMR0 BIT 1=1
TRANSITION
DETECTION
ALE
o
r
P
e
RESET
CSI
t
e
l
o
s
b
O
c
u
d
(t s)
)
s
t(
o
r
P
o
s
b
O
-
DISABLE BUS
INTERFACE
CLR
PD
EEPROM SELECT
APD
COUNTER
FLASH SELECT
EDGE
DETECT
PD
PLD
CLKIN
SRAM SELECT
POWER DOWN
(PDN) SELECT
DISABLE
FLASH/EEPROM/SRAM
AI02891
Table 29. PSD Timing and Standby Current during Power-down Mode
Mode
PLD Propagation Delay
Memory
Access Time
Access Recovery Time
to Normal Access
Power-down
Normal tPD (Note 1)
No Access
tLVDV
Typical Standby Current
5V VCC
3V VCC
75µA (Note 2)
25µA (Note 2)
Note: 1. Power-down does not affect the operation of the PLD. The PLD operation in this mode is based only on the Turbo Bit.
2. Typical current consumption assuming no PLD inputs are changing state and the PLD Turbo Bit is ’0.’
Doc ID 10552 Rev 3
63/109
PSD813F2V, PSD854F2V
For Users of the HC11 (or compatible)
The HC11 turns off its E clock when it sleeps.
Therefore, if you are using an HC11 (or compatible) in your design, and you wish to use the Power-down mode, you must not connect the E clock
to CLKIN (PD1). You should instead connect a
crystal oscillator to CLKIN (PD1). The crystal oscillator frequency must be less than 15 times the frequency of AS. The reason for this is that if the
frequency is greater than 15 times the frequency
of AS, the PSD keeps going into Power-down
mode.
Other Power Saving Options
The PSD offers other reduced power saving options that are independent of the Power-down
mode. Except for the PSD Chip Select Input (CSI,
PD2) feature, they are enabled by setting bits in
PMMR0 and PMMR2.
Figure 33. Enable Power-down Flow Chart
RESET
Enable APD
Set PMMR0 Bit 1 = 1
OPTIONAL
Disable desired inputs to PLD
by setting PMMR0 bits 4 and 5
and PMMR2 bits 2 through 6.
ALE/AS idle
for 15 CLKIN
clocks?
No
Yes
c
u
d
PSD in Power
Down Mode
u
d
o
r
P
e
o
s
b
O
-
t
e
l
o
s
b
O
64/109
AI02892
PLD Power Management
The power and speed of the PLDs are controlled
by the Turbo Bit (Bit 3) in PMMR0. By setting the
bit to '1,' the Turbo mode is off and the PLDs consume the specified standby current when the inputs are not switching for an extended time of
70ns. The propagation delay time is increased by
10ns after the Turbo Bit is set to '1' (turned off)
when the inputs change at a composite frequency
of less than 15 MHz. When the Turbo Bit is reset
to '0' (turned on), the PLDs run at full power and
speed. The Turbo Bit affects the PLD’s DC power,
AC power, and propagation delay.
Blocking MCU control signals with the bits of
PMMR2 can further reduce PLD AC power consumption.
e
t
le
)
s
(
ct
o
r
P
)
s
t(
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
Table 30. Power Management Mode Registers PMMR0 (Note 1)
Bit 0
X
0
Bit 1
APD Enable
Not used, and should be set to zero.
0 = off Automatic Power-down (APD) is disabled.
1 = on Automatic Power-down (APD) is enabled.
Bit 2
X
0
Bit 3
PLD Turbo
Not used, and should be set to zero.
0 = on PLD Turbo mode is on
1 = off PLD Turbo mode is off, saving power.
0 = on
Bit 4
PLD Array clk
CLKIN (PD1) input to the PLD AND Array is connected. Every change of CLKIN
(PD1) Powers-up the PLD when Turbo Bit is ’0.’
1 = off CLKIN (PD1) input to PLD AND Array is disconnected, saving power.
0 = on CLKIN (PD1) input to the PLD macrocells is connected.
Bit 5
PLD MCell clk
1 = off CLKIN (PD1) input to PLD macrocells is disconnected, saving power.
Bit 6
X
0
Not used, and should be set to zero.
Bit 7
X
0
Not used, and should be set to zero.
c
u
d
)
s
t(
Note: 1. The bits of this register are cleared to zero following Power-up. Subsequent Reset (RESET) pulses do not clear the registers.
Table 31. Power Management Mode Registers PMMR2 (Note 1)
Bit 0
X
0
Not used, and should be set to zero.
Bit 1
X
0
Not used, and should be set to zero.
PLD Array
CNTL0
0 = on Cntl0 input to the PLD AND Array is connected.
Bit 2
PLD Array
CNTL1
0 = on Cntl1 input to the PLD AND Array is connected.
PLD Array
CNTL2
0 = on Cntl2 input to the PLD AND Array is connected.
PLD Array
ALE
0 = on ALE input to the PLD AND Array is connected.
Bit 3
Bit 4
Bit 5
t
e
l
o
Bit 7
X
o
s
b
O
-
1 = off Cntl0 input to PLD AND Array is disconnected, saving power.
1 = off Cntl1 input to PLD AND Array is disconnected, saving power.
)
s
(
ct
1 = off Cntl2 input to PLD AND Array is disconnected, saving power.
u
d
o
1 = off ALE input to PLD AND Array is disconnected, saving power.
r
P
e
PLD Array
DBE
Bit 6
e
t
le
o
r
P
0 = on DBE input to the PLD AND Array is connected.
1 = off DBE input to PLD AND Array is disconnected, saving power.
0
Not used, and should be set to zero.
Note: 1. The bits of this register are cleared to zero following Power-up. Subsequent Reset (RESET) pulses do not clear the registers.
s
b
O
Doc ID 10552 Rev 3
65/109
PSD813F2V, PSD854F2V
PSD Chip Select Input (CSI, PD2)
PD2 of Port D can be configured in PSDsoft Express as PSD Chip Select Input (CSI). When Low,
the signal selects and enables the internal Flash
memory, EEPROM, SRAM, and I/O blocks for
READ or WRITE operations involving the PSD. A
High on PSD Chip Select Input (CSI, PD2) disables the Flash memory, EEPROM, and SRAM,
and reduces the PSD power consumption. However, the PLD and I/O signals remain operational
when PSD Chip Select Input (CSI, PD2) is High.
There may be a timing penalty when using PSD
Chip Select Input (CSI, PD2) depending on the
speed grade of the PSD that you are using. See
the timing parameter tSLQV in Table 61., page 94
or Table 62., page 95.
Input Clock
The PSD provides the option to turn off CLKIN
(PD1) to the PLD to save AC power consumption.
CLKIN (PD1) is an input to the PLD AND Array and
the Output Macrocells (OMC).
During Power-down mode, or, if CLKIN (PD1) is
not being used as part of the PLD logic equation,
the clock should be disabled to save AC power.
CLKIN (PD1) is disconnected from the PLD AND
Array or the Macrocells block by setting Bits 4 or 5
to a 1 in PMMR0.
Input Control Signals
The PSD provides the option to turn off the input
control signals (CNTL0, CNTL1, CNTL2, Address
Strobe (ALE/AS, PD0) and DBE) to the PLD to
save AC power consumption. These control signals are inputs to the PLD AND Array. During
Power-down mode, or, if any of them are not being
used as part of the PLD logic equation, these control signals should be disabled to save AC power.
They are disconnected from the PLD AND Array
by setting Bits 2, 3, 4, 5, and 6 to a 1 in PMMR2.
c
u
d
Table 32. APD Counter Operation
APD Enable Bit
ALE PD Polarity
ALE Level
0
X
X
Not Counting
1
X
Pulsing
Not Counting
1
1
1
1
0
0
)
s
(
ct
o
s
b
O
-
e
t
le
Counting (Generates PDN after 15 Clocks)
Counting (Generates PDN after 15 Clocks)
u
d
o
r
P
e
t
e
l
o
s
b
O
66/109
o
r
P
APD Counter
Doc ID 10552 Rev 3
)
s
t(
PSD813F2V, PSD854F2V
RESET TIMING AND DEVICE STATUS AT RESET
Power-Up Reset
Upon Power-up, the PSD requires a Reset (RESET) pulse of duration tNLNH-PO after VCC is
steady. During this period, the device loads internal configurations, clears some of the registers
and sets the Flash memory into Operating mode.
After the rising edge of Reset (RESET), the PSD
remains in the Reset mode for an additional period, tOPR, before the first memory access is allowed.
The Flash memory is reset to the READ Mode
upon Power-up. Sector Select (FS0-FS7 and
CSBOOT0-CSBOOT3) must all be Low, Write
Strobe (WR, CNTL0) High, during Power On Reset for maximum security of the data contents and
to remove the possibility of a byte being written on
the first edge of Write Strobe (WR, CNTL0). Any
Flash memory WRITE cycle initiation is prevented
automatically when VCC is below VLKO.
Warm Reset
Once the device is up and running, the device can
be reset with a pulse of a much shorter duration,
tNLNH.
The same tOPR period is needed before the device
is operational after warm reset. Figure 34 shows
the timing of the Power-up and warm reset.
I/O Pin, Register and PLD Status at Reset
Table 33., page 68 shows the I/O pin, register and
PLD status during Power On Reset, warm reset
and Power-down mode. PLD outputs are always
valid during warm reset, and they are valid in Power On Reset once the internal PSD Configuration
bits are loaded. This loading of PSD is completed
typically long before the VCC ramps up to operating level. Once the PLD is active, the state of the
outputs are determined by the PSDabel equations.
Reset of Flash Memory Erase and Program
Cycles (on the PSD834Fx)
A Reset (RESET) also resets the internal Flash
memory state machine. During a Flash memory
Program or Erase cycle, Reset (RESET) terminates the cycle and returns the Flash memory to
the Read Mode within a period of tNLNH-A.
Figure 34. Reset (RESET) Timing
c
u
d
e
t
le
VCC(min)
VCC
tNLNH-PO
tOPR
Power-On Reset
)
s
(
ct
RESET
o
s
b
O
-
u
d
o
)
s
t(
o
r
P
tNLNH
tNLNH-A
tOPR
Warm Reset
AI02866b
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
67/109
PSD813F2V, PSD854F2V
Table 33. Status During Power-On Reset, Warm Reset and Power-down Mode
Port Configuration
Power-On Reset
Warm Reset
Power-down Mode
MCU I/O
Input mode
Input mode
Unchanged
PLD Output
Valid after internal PSD
configuration bits are
loaded
Valid
Depends on inputs to PLD
(addresses are blocked in
PD mode)
Address Out
Tri-stated
Tri-stated
Not defined
Data Port
Tri-stated
Tri-stated
Tri-stated
Peripheral I/O
Tri-stated
Tri-stated
Tri-stated
Register
Power-On Reset
Warm Reset
Power-down Mode
PMMR0 and PMMR2
Cleared to '0'
Unchanged
Unchanged
Macrocells flip-flop status
Cleared to '0' by internal
Power-On Reset
Depends on .re and .pr
equations
Depends on .re and .pr
equations
VM Register1
Initialized, based on the
selection in PSDsoft
Configuration menu
Initialized, based on the
selection in PSDsoft
Configuration menu
Unchanged
All other registers
Cleared to '0'
Cleared to '0'
Unchanged
o
r
P
c
u
d
)
s
t(
Note: 1. The SR_cod and PeriphMode bits in the VM Register are always cleared to '0' on Power-On Reset or Warm Reset.
e
t
le
)
s
(
ct
o
s
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
68/109
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
PROGRAMMING IN-CIRCUIT USING THE JTAG SERIAL INTERFACE
The JTAG Serial Interface block can be enabled
on Port C (see Table 34., page 70). All memory
blocks (primary and secondary Flash memory),
PLD logic, and PSD Configuration Register bits
may be programmed through the JTAG Serial Interface block. A blank device can be mounted on
a printed circuit board and programmed using
JTAG.
The standard JTAG signals (IEEE 1149.1) are
TMS, TCK, TDI, and TDO. Two additional signals,
TSTAT and TERR, are optional JTAG extensions
used to speed up Program and Erase cycles.
By default, on a blank PSD (as shipped from the
factory or after erasure), four pins on Port C are
enabled for the basic JTAG signals TMS, TCK,
TDI, and TDO.
See Application Note AN1153 for more details on
JTAG In-System Programming (ISP).
Standard JTAG Signals
The standard JTAG signals (TMS, TCK, TDI, and
TDO) can be enabled by any of three different conditions that are logically ORed. When enabled,
TDI, TDO, TCK, and TMS are inputs, waiting for a
JTAG serial command from an external JTAG controller device (such as FlashLINK or Automated
Test Equipment). When the enabling command is
received, TDO becomes an output and the JTAG
channel is fully functional inside the PSD. The
same command that enables the JTAG channel
may optionally enable the two additional JTAG signals, TSTAT and TERR.
The following symbolic logic equation specifies the
conditions enabling the four basic JTAG signals
(TMS, TCK, TDI, and TDO) on their respective
Port C pins. For purposes of discussion, the logic
label JTAG_ON is used. When JTAG_ON is true,
the four pins are enabled for JTAG. When
JTAG_ON is false, the four pins can be used for
general PSD I/O.
JTAG_ON = PSDsoft_enabled +
/* An NVM configuration bit inside the
PSD is set by the designer in the
PSDsoft Express Configuration utility.
)
s
(
ct
u
d
o
r
P
e
t
e
l
o
This dedicates the pins for JTAG at all
times (compliant with IEEE 1149.1 */
Microcontroller_enabled +
/* The microcontroller can set a bit at
run-time by writing to the PSD
register, JTAG Enable. This register is
located at address CSIOP + offset C7h.
Setting the JTAG_ENABLE bit in this
register will enable the pins for JTAG
use. This bit is cleared by a PSD reset
or the microcontroller. See Table
35., page 71 for bit definition. */
PSD_product_term_enabled;
/* A dedicated product term (PT) inside
the PSD can be used to enable the JTAG
pins. This PT has the reserved name
JTAGSEL. Once defined as a node in
PSDabel, the designer can write an
equation for JTAGSEL. This method is
used when the Port C JTAG pins are
multiplexed with other I/O signals. It
is recommended to logically tie the
node JTAGSEL to the JEN\ signal on the
Flashlink cable when multiplexing JTAG
signals. See Application Note 1153 for
details. */
The state of the PSD Reset (RESET) signal does
not interrupt (or prevent) JTAG operations if the
JTAG pins are dedicated by an NVM configuration
bit (via PSDsoft Express). However, Reset (RESET) will prevent or interrupt JTAG operations if
the JTAG enable register is used to enable the
JTAG pins.
The PSD supports JTAG In-System-Configuration
(ISC) commands, but not Boundary Scan. The
PSDsoft Express software tool and FlashLINK
JTAG programming cable implement the JTAG InSystem-Configuration (ISC) commands. A definition of these JTAG In-System-Configuration (ISC)
commands and sequences is defined in a supplemental document available from ST. This document is needed only as a reference for designers
who use a FlashLINK to program their PSD.
c
u
d
e
t
le
)
s
t(
o
r
P
o
s
b
O
-
s
b
O
Doc ID 10552 Rev 3
69/109
PSD813F2V, PSD854F2V
JTAG Extensions
TSTAT and TERR are two JTAG extension signals
enabled by an “ISC_ENABLE” command received
over the four standard JTAG signals (TMS, TCK,
TDI, and TDO). They are used to speed Program
and Erase cycles by indicating status on PSD signals instead of having to scan the status out serially using the standard JTAG channel. See
Application Note AN1153.
TERR indicates if an error has occurred when
erasing a sector or programming a byte in Flash
memory. This signal goes Low (active) when an
Error condition occurs, and stays Low until an
“ISC_CLEAR” command is executed or a chip Reset (RESET) pulse is received after an
“ISC_DISABLE” command.
TSTAT behaves the same as Ready/Busy described in the section entitled Ready/Busy
(PC3), page 20. TSTAT is High when the PSD device is in READ Mode (primary and secondary
Flash memory contents can be read). TSTAT is
Low when Flash memory Program or Erase cycles
are in progress, and also when data is being written to the secondary Flash memory.
TSTAT and TERR can be configured as opendrain type signals during an “ISC_ENABLE” command. This facilitates a wired-OR connection of
TSTAT signals from multiple PSD devices and a
wired-OR connection of TERR signals from those
same devices. This is useful when several PSD
devices are “chained” together in a JTAG environment.
)
s
(
ct
Security and Flash memory Protection
When the security bit is set, the device cannot be
read on a Device Programmer or through the
JTAG Port. When using the JTAG Port, only a Full
Chip Erase command is allowed.
All other Program, Erase and Verify commands
are blocked. Full Chip Erase returns the part to a
non-secured blank state. The Security Bit can be
set in PSDsoft Express Configuration.
All primary and secondary Flash memory sectors
can individually be sector protected against erasures. The sector protect bits can be set in PSDsoft Express Configuration.
Table 34. JTAG Port Signals
Port C Pin
Description
PC0
TMS
Mode Select
PC1
TCK
Clock
PC3
TSTAT
PC4
TERR
PC5
TDI
o
s
b
O
-
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
TDO
c
u
d
Status
)
s
t(
Error Flag
ro
P
e
let
PC6
u
d
o
70/109
JTAG Signals
Serial Data In
Serial Data Out
PSD813F2V, PSD854F2V
INITIAL DELIVERY STATE
When delivered from ST, the PSD device has all
bits in the memory and PLDs set to ’1.’ The PSD
Configuration Register bits are set to ’0.’ The code,
configuration, and PLD logic are loaded using the
programming procedure. Information for programming the device is available directly from ST.
Please contact your local sales representative.
Table 35. JTAG Enable Register
0 = off JTAG port is disabled.
Bit 0
JTAG_Enable
1 = on JTAG port is enabled.
Bit 1
X
0
Not used, and should be set to zero.
Bit 2
X
0
Not used, and should be set to zero.
Bit 3
X
0
Not used, and should be set to zero.
Bit 4
X
0
Not used, and should be set to zero.
Bit 5
X
0
Not used, and should be set to zero.
Bit 6
X
0
Not used, and should be set to zero.
Bit 7
X
0
Not used, and should be set to zero.
c
u
d
)
s
t(
Note: 1. The state of Reset (RESET) does not interrupt (or prevent) JTAG operations if the JTAG signals are dedicated by an NVM Configuration bit (via PSDsoft Express). However, Reset (RESET) prevents or interrupts JTAG operations if the JTAG enable register is
used to enable the JTAG signals.
e
t
le
)
s
(
ct
o
r
P
o
s
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
71/109
PSD813F2V, PSD854F2V
AC/DC PARAMETERS
These tables describe the AD and DC parameters
of the PSD:
❏ DC Electrical Specification
❏ AC Timing Specification
■
PLD Timing
– Combinatorial Timing
– Synchronous Clock Mode
– Asynchronous Clock Mode
– Input Macrocell Timing
■
MCU Timing
– READ Timing
– WRITE Timing
– Peripheral Mode Timing
– Power-down and Reset Timing
The following are issues concerning the parameters presented:
– In the DC specification the supply current is
given for different modes of operation. Before
calculating the total power consumption,
determine the percentage of time that the PSD
is in each mode. Also, the supply power is
considerably different if the Turbo Bit is ’0.’
– The AC power component gives the PLD,
Flash memory, and SRAM mA/MHz
specification. Figures 35 and 36 show the PLD
mA/MHz as a function of the number of
Product Terms (PT) used.
– In the PLD timing parameters, add the
required delay when Turbo Bit is ’0.’
Figure 35. PLD ICC /Frequency Consumption (5V range)
110
VCC = 5V
100
BO
(1
ON
TUR
80
FF
70
O
T
RB
50
40
e
t
le
O
URB
O
60
TU
ICC – (mA)
c
u
d
)
00%
90
30
o
s
b
O
-
F
20
O
B
UR
OF
)
s
(
ct
T
10
0
0
5
10
15
ON
)
(25%
o
r
P
PT 100%
PT 25%
20
25
du
HIGHEST COMPOSITE FREQUENCY AT PLD INPUTS (MHz)
o
r
P
e
AI02894
Figure 36. PLD ICC /Frequency Consumption (3V range)
60
)
100%
ON (
T
40
FF
30
O
5%)
(2
O ON
O
O
O
URB
TURB
RB
bs
ICC – (mA)
t
e
l
o
VCC = 3V
50
TU
20
10
PT 100%
PT 25%
F
O
RB
TU
OF
0
0
5
10
15
20
HIGHEST COMPOSITE FREQUENCY AT PLD INPUTS (MHz)
72/109
Doc ID 10552 Rev 3
25
AI03100
)
s
t(
PSD813F2V, PSD854F2V
Table 36. Example of PSD Typical Power Calculation at VCC = 5.0V (Turbo Mode On)
Conditions
Highest Composite PLD input frequency
(Freq PLD)
= 8 MHz
MCU ALE frequency (Freq ALE)
= 4 MHz
% Flash memory Access
= 80%
% SRAM access
= 15%
% I/O access
= 5% (no additional power above base)
Operational Modes
% Normal
= 10%
% Power-down Mode
= 90%
Number of product terms used
(from fitter report)
= 45 PT
% of total product terms
= 45/182 = 24.7%
Turbo Mode
= ON
Calculation (using typical values)
ICC total
c
u
d
)
s
t(
o
r
P
= Ipwrdown x %pwrdown + %normal x (ICC (ac) + ICC (dc))
= Ipwrdown x %pwrdown + % normal x (%flash x 2.5mA/MHz x Freq ALE
e
t
le
+ %SRAM x 1.5mA/MHz x Freq ALE
o
s
b
O
-
+ % PLD x 2mA/MHz x Freq PLD
+ #PT x 400µA/PT)
= 50µA x 0.90 + 0.1 x (0.8 x 2.5mA/MHz x 4 MHz
)
s
(
ct
u
d
o
r
P
e
t
e
l
o
+ 0.15 x 1.5mA/MHz x 4 MHz
+ 2mA/MHz x 8 MHz
+ 45 x 0.4mA/PT)
= 45µA + 0.1 x (8 + 0.9 + 16 + 18mA)
= 45µA + 0.1 x 42.9
= 45µA + 4.29mA
= 4.34mA
This is the operating power with no EEPROM WRITE or Flash memory Erase cycles in progress. Calculation is based
on IOUT = 0mA.
s
b
O
Doc ID 10552 Rev 3
73/109
PSD813F2V, PSD854F2V
Table 37. Example of PSD Typical Power Calculation at VCC = 5.0V (Turbo Mode Off)
Conditions
Highest Composite PLD input frequency
(Freq PLD)
= 8 MHz
MCU ALE frequency (Freq ALE)
= 4 MHz
% Flash memory Access
= 80%
% SRAM access
= 15%
% I/O access
= 5% (no additional power above base)
Operational Modes
% Normal
= 10%
% Power-down Mode
= 90%
Number of product terms used
(from fitter report)
= 45 PT
% of total product terms
= 45/182 = 24.7%
Turbo Mode
= Off
Calculation (using typical values)
ICC total
c
u
d
)
s
t(
o
r
P
= Ipwrdown x %pwrdown + %normal x (ICC (ac) + ICC (dc))
= Ipwrdown x %pwrdown + % normal x (%flash x 2.5mA/MHz x Freq ALE
e
t
le
+ %SRAM x 1.5mA/MHz x Freq ALE
o
s
b
O
-
+ % PLD x (from graph using Freq PLD))
= 50µA x 0.90 + 0.1 x (0.8 x 2.5mA/MHz x 4 MHz
+ 0.15 x 1.5mA/MHz x 4 MHz
)
s
(
ct
+ 24mA)
= 45µA + 0.1 x (8 + 0.9 + 24)
u
d
o
r
P
e
= 45µA + 0.1 x 32.9
= 45µA + 3.29mA
= 3.34mA
This is the operating power with no EEPROM WRITE or Flash memory Erase cycles in progress. Calculation is based
on IOUT = 0mA.
t
e
l
o
s
b
O
74/109
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
MAXIMUM RATING
Stressing the device above the rating listed in the
Absolute Maximum Ratings” table may cause permanent damage to the device. These are stress
ratings only and operation of the device at these or
any other conditions above those indicated in the
Operating sections of this specification is not im-
plied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device
reliability. Refer also to the STMicroelectronics
SURE Program and other relevant quality documents.
Table 38. Absolute Maximum Ratings
Symbol
Parameter
TSTG
Storage Temperature
TLEAD
Lead Temperature during Soldering (20 seconds max.)1
Min.
Max.
Unit
–65
125
°C
235
°C
VIO
Input and Output Voltage (Q = VOH or Hi-Z)
–0.6
7.0
V
VCC
Supply Voltage
–0.6
7.0
V
VPP
Device Programmer Supply Voltage
–0.6
14.0
V
VESD
Electrostatic Discharge Voltage (Human Body model) 2
–2000
2000
c
u
d
Note: 1. IPC/JEDEC J-STD-020A
2. JEDEC Std JESD22-A114A (C1=100 pF, R1=1500 Ω, R2=500 Ω)
e
t
le
)
s
(
ct
)
s
t(
V
o
r
P
o
s
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
75/109
PSD813F2V, PSD854F2V
DC AND AC PARAMETERS
This section summarizes the operating and measurement conditions, and the DC and AC characteristics of the device. The parameters in the DC
and AC Characteristic tables that follow are derived from tests performed under the Measure-
ment Conditions summarized in the relevant
tables. Designers should check that the operating
conditions in their circuit match the measurement
conditions when relying on the quoted parameters.
Table 39. Operating Conditions (5V devices)
Symbol
VCC
Parameter
Min.
Max.
Unit
Supply Voltage
4.5
5.5
V
Ambient Operating Temperature (industrial)
–40
85
°C
0
70
°C
Min.
Max.
Unit
Supply Voltage
3.0
3.6
Ambient Operating Temperature (industrial)
–40
85
0
od
TA
Ambient Operating Temperature (commercial)
Table 40. Operating Conditions (3V devices)
Symbol
VCC
Parameter
TA
Ambient Operating Temperature (commercial)
A
Address Input
C
CEout Output
D
Input Data
E
E Input
G
Internal WDOG_ON signal
I
Interrupt Input
L
ALE Input
N
RESET Input or Output
P
Port Signal Output
Q
Output Data
R
WR, UDS, LDS, DS, IORD, PSEN Inputs
s
b
O
W
uc
°C
°C
t
so
L
b
O
-
u
d
o
H
Time
Logic Level Low or ALE
Logic Level High
V
Valid
X
No Longer a Valid Logic Level
Z
Float
PW
Pulse Width
Note: Example: tAVLX = Time from Address Valid to ALE Invalid.
r
P
e
t
e
l
o
S
T
r
P
e
t
le
V
Table 42. AC Signal Behavior Symbols for PLD
Timing
Table 41. AC Signal Letters for PLD Timing
)
s
(
ct
70
)
s
t(
M
Chip Select Input
R/W Input
Internal PDN Signal
Output Macrocell
Note: Example: tAVLX = Time from Address Valid to ALE Invalid.
Table 43. AC Measurement Conditions
Symbol
CL
Parameter
Load Capacitance
Max.
30
Note: 1. Output Hi-Z is defined as the point where data out is no longer driven.
76/109
Min.
Doc ID 10552 Rev 3
Unit
pF
PSD813F2V, PSD854F2V
Table 44. Capacitance
Symbol
Parameter
Test Condition
Typ.2
Max.
Unit
CIN
Input Capacitance (for input pins)
VIN = 0V
4
6
pF
COUT
Output Capacitance (for input/
output pins)
VOUT = 0V
8
12
CVPP
Capacitance (for CNTL2/VPP)
VPP = 0V
18
25
pF
pF
Note: 1. Sampled only, not 100% tested.
2. Typical values are for TA = 25°C and nominal supply voltages.
Figure 37. AC Measurement I/O Waveform
Figure 38. AC Measurement Load Circuit
2.01 V
3.0V
195 Ω
Test Point
1.5V
Device
Under Test
0V
c
u
d
AI03103b
e
t
le
Figure 39. Switching Waveforms – Key
WAVEFORMS
)
s
(
ct
o
r
P
e
s
b
O
t
e
l
o
du
o
s
b
O
INPUTS
)
s
t(
CL = 30 pF
(Including Scope and
Jig Capacitance)
AI03104b
o
r
P
OUTPUTS
STEADY INPUT
STEADY OUTPUT
MAY CHANGE FROM
HI TO LO
WILL BE CHANGING
FROM HI TO LO
MAY CHANGE FROM
LO TO HI
WILL BE CHANGING
LO TO HI
DON'T CARE
CHANGING, STATE
UNKNOWN
OUTPUTS ONLY
CENTER LINE IS
TRI-STATE
AI03102
Doc ID 10552 Rev 3
77/109
PSD813F2V, PSD854F2V
Table 45. DC Characteristics (5V devices)
Symbol
Parameter
Test Condition
(in addition to those in
Table 39., page 76)
Min.
Typ.
Max.
Unit
VIH
Input High Voltage
4.5 V < VCC < 5.5 V
2
VCC +0.5
V
VIL
Input Low Voltage
4.5 V < VCC < 5.5 V
–0.5
0.8
V
VIH1
Reset High Level Input Voltage
(Note 1)
0.8VCC
VCC +0.5
V
VIL1
Reset Low Level Input Voltage
(Note 1)
–0.5
0.2VCC –0.1
V
VHYS
Reset Pin Hysteresis
0.3
VLKO
VCC (min) for Flash Erase and
Program
2.5
VOL
Output Low Voltage
VOH
V
4.2
V
IOL = 20µA, VCC = 4.5 V
0.01
0.1
V
IOL = 8mA, VCC = 4.5 V
0.25
0.45
V
ILI
Input Leakage Current
ILO
Output Leakage Current
4.4
4.49
IOH = –2mA, VCC = 4.5 V
2.4
3.9
VSS < VIN < VCC
–1
±0.1
0.45 < VOUT < VCC
–10
ro
10
ICC (DC)
400
700
µA/PT
(Note 5)
15
30
mA
0
0
mA
0
0
mA
PLD_TURBO = On,
f = 0 MHz
Operating
Supply
Current
o
s
b
O
-
Flash memory
During Flash memory
WRITE/Erase Only
Read only, f = 0 MHz
(s)
SRAM
ICC (AC)
du
Flash memory AC Adder
o
r
P
e
5
(Note )
f = 0 MHz
ct
PLD AC Adder
V
c
u
d
1
0
V
µA
µA
µA/PT
note 4
SRAM AC Adder
Note: 1.
2.
3.
4.
5.
±5
P
e
let
PLD_TURBO = Off,
f = 0 MHz (Note 5)
PLD Only
)
s
t(
IOH = –20µA, VCC = 4.5 V
Output High Voltage
2.5
3.5
mA/
MHz
1.5
3.0
mA/
MHz
Max.
Unit
t
e
l
o
Reset (RESET) has hysteresis. VIL1 is valid at or below 0.2VCC –0.1. VIH1 is valid at or above 0.8VCC.
CSI deselected or internal Power-down mode is active.
PLD is in non-Turbo mode, and none of the inputs are switching.
Please see Figure 35., page 72 for the PLD current calculation.
IOUT = 0mA
s
b
O
Table 46. DC Characteristics (3V devices)
Symbol
Parameter
Conditions
Min.
Typ.
VIH
High Level Input Voltage
3.0 V < VCC < 3.6 V
0.7VCC
VCC +0.5
V
VIL
Low Level Input Voltage
3.0 V < VCC < 3.6 V
–0.5
0.8
V
VIH1
Reset High Level Input Voltage
(Note 1)
0.8VCC
VCC +0.5
V
VIL1
Reset Low Level Input Voltage
(Note 1)
–0.5
0.2VCC –0.1
V
78/109
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
Symbol
Parameter
Conditions
Min.
VHYS
Reset Pin Hysteresis
0.3
VLKO
VCC (min) for Flash Erase and
Program
1.5
VOL
Output Low Voltage
VOH
Typ.
Max.
Unit
V
2.2
V
IOL = 20µA, VCC = 3.0 V
0.01
0.1
V
IOL = 4mA, VCC = 3.0 V
0.15
0.45
V
IOH = –20µA, VCC = 3.0 V
2.9
2.99
V
IOH = –1mA, VCC = 3.0 V
2.7
2.8
V
Output High Voltage
ILI
Input Leakage Current
VSS < VIN < VCC
–1
±0.1
1
µA
ILO
Output Leakage Current
0.45 < VIN < VCC
–10
±5
10
µA
PLD Only
ICC (DC)
(Note
5)
Operating
Supply
Current
Flash memory
PLD_TURBO = Off,
f = 0 MHz (Note 3)
0
PLD_TURBO = On,
f = 0 MHz
200
During Flash memory
WRITE/Erase Only
10
Read only, f = 0 MHz
0
uc
0
mA
0
0
mA
1.5
2.0
mA/
MHz
0.8
1.5
mA/
MHz
SRAM
f = 0 MHz
e
t
le
PLD AC Adder
ICC (AC)
Flash memory AC Adder
5
(Note )
SRAM AC Adder
Note: 1.
2.
3.
4.
5.
o
s
b
O
-
Pr
µA/PT
od
400
25
)
s
t(
µA/PT
mA
note 4
Reset (RESET) has hysteresis. VIL1 is valid at or below 0.2VCC –0.1. VIH1 is valid at or above 0.8VCC.
CSI deselected or internal PD is active.
PLD is in non-Turbo mode, and none of the inputs are switching.
Please see Figure 36., page 72 for the PLD current calculation.
IOUT = 0mA
)
s
(
ct
u
d
o
Figure 40. Input to Output Disable / Enable
r
P
e
INPUT
s
b
O
t
e
l
o
tER
tEA
INPUT TO
OUTPUT
ENABLE/DISABLE
AI02863
Doc ID 10552 Rev 3
79/109
PSD813F2V, PSD854F2V
Table 47. CPLD Combinatorial Timing (5V devices)
-70
Symbol
Parameter
-90
-15
Conditions
Min
Max
Min
Max
Min
Fast
PT
Max Aloc
tPD
CPLD Input Pin/
Feedback to CPLD
Combinatorial Output
20
25
32
tEA
CPLD Input to CPLD
Output Enable
21
26
tER
CPLD Input to CPLD
Output Disable
21
tARP
CPLD Register Clear
or Preset Delay
21
tARPW
CPLD Register Clear
or Preset Pulse Width
tARD
CPLD Array Delay
10
Any
macrocell
–2
ns
32
+ 10
–2
ns
26
32
+ 10
–2
ns
26
33
+ 10
–2
ns
29
11
+ 10
16
22
+2
Table 48. CPLD Combinatorial Timing (3V devices)
-12
Parameter
Min
tPD
CPLD Input Pin/
Feedback to CPLD
Combinatorial Output
tEA
CPLD Input to CPLD
Output Enable
tER
CPLD Input to CPLD
Output Disable
tARP
CPLD Register Clear
or
Preset Delay
tARPW
CPLD Register Clear
or
Preset Pulse Width
t
e
l
o
r
P
e
CPLD Array Delay
Max
Min
40
)
s
(
ct
u
d
o
tARD
-15
-20
Conditions
Min
e
t
le
45
o
s
b
O
-
50
+4
Turbo Slew
Off
rate1
Unit
+ 20
–6
ns
45
50
+ 20
–6
ns
43
45
50
+ 20
–6
ns
40
43
48
+ 20
–6
ns
30
25
35
29
+ 20
33
+4
Note: 1. Fast Slew Rate output available on PA3-PA0, PB3-PB0, and PD2-PD0. Decrement times by given amount.
s
b
O
80/109
)
s
t(
43
25
Any
macrocell
Max
c
u
d
o
r
P
PT
Aloc
Max
ns
ns
Note: 1. Fast Slew Rate output available on PA3-PA0, PB3-PB0, and PD2-PD0. Decrement times by given amount.
Symbol
Unit
+ 10
20
+2
Turbo Slew
Off
rate1
Doc ID 10552 Rev 3
ns
ns
PSD813F2V, PSD854F2V
Figure 41. Synchronous Clock Mode Timing – PLD
tCH
tCL
CLKIN
tS
tH
INPUT
tCO
REGISTERED
OUTPUT
AI02860
Table 49. CPLD Macrocell Synchronous Clock Mode Timing (5V devices)
-70
Symbol
Parameter
Min
fMAX
1/(tS+tCO)
Maximum
Frequency
Internal
Feedback
(fCNT)
1/(tS+tCO–10)
66.6
1/(tCH+tCL)
83.3
tS
Input Setup
Time
tH
Input Hold Time
tCH
Clock High
Time
tCL
Clock Low Time
tCO
Clock to Output
Delay
CPLD Array
Delay
Minimum Clock
Period 2
Min
40.0
(s)
12
-15
Max
Min
30.30
Max
Fast
PT
Aloc
Turbo Slew
Off
rate1
c
u
d
25.00
e
t
le
43.48
o
s
b
O
50.00
Unit
)
s
t(
MHz
o
r
P
31.25
MHz
35.71
MHz
15
20
0
0
0
ns
Clock Input
6
10
15
ns
Clock Input
6
10
15
ns
ct
u
d
o
r
P
e
t
e
l
o
s
b
O
tMIN
Max
Maximum
Frequency
External
Feedback
Maximum
Frequency
Pipelined Data
tARD
-90
Conditions
+2
Clock Input
13
18
22
Any macrocell
11
16
22
tCH+tCL
12
20
+ 10
ns
–2
+2
30
ns
ns
ns
Note: 1. Fast Slew Rate output available on PA3-PA0, PB3-PB0, and PD2-PD0. Decrement times by given amount.
2. CLKIN (PD1) tCLCL = tCH + tCL.
Doc ID 10552 Rev 3
81/109
PSD813F2V, PSD854F2V
Table 50. CPLD Macrocell Synchronous Clock Mode Timing (3V devices)
-12
Symbol
Parameter
Min
fMAX
-15
-20
Conditions
Max
Min
Max
Min
Max
Turbo Slew
Off
rate1
PT
Aloc
Maximum
Frequency
External Feedback
1/(tS+tCO)
22.2
18.8
15.8
MHz
Maximum
Frequency
Internal Feedback
(fCNT)
1/(tS+tCO–10)
28.5
23.2
18.8
MHz
1/(tCH+tCL)
40.0
33.3
31.2
MHz
Maximum
Frequency
Pipelined Data
tS
Input Setup Time
20
25
30
tH
Input Hold Time
0
0
0
tCH
Clock High Time
Clock Input
15
15
16
tCL
Clock Low Time
Clock Input
10
15
16
tCO
Clock to Output
Delay
Clock Input
25
28
33
tARD
CPLD Array Delay
Any macrocell
25
29
33
tMIN
Minimum Clock
Period2
tCH+tCL
25
+4
32
)
s
(
ct
o
s
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
ns
ns
)
s
t(
ns
e
t
le
29
+ 20
c
u
d
o
r
P
+4
Note: 1. Fast Slew Rate output available on PA3-PA0, PB3-PB0, and PD2-PD0. Decrement times by given amount.
2. CLKIN (PD1) tCLCL = tCH + tCL.
82/109
Unit
ns
–6
ns
ns
ns
PSD813F2V, PSD854F2V
Figure 42. Asynchronous Reset / Preset
tARPW
RESET/PRESET
INPUT
tARP
REGISTER
OUTPUT
AI02864
Figure 43. Asynchronous Clock Mode Timing (product term clock)
tCHA
tCLA
CLOCK
tSA
tHA
INPUT
c
u
d
tCOA
REGISTERED
OUTPUT
e
t
le
)
s
(
ct
)
s
t(
o
r
P
AI02859
o
s
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
83/109
PSD813F2V, PSD854F2V
Table 51. CPLD Macrocell Asynchronous Clock Mode Timing (5V devices)
-70
Symbol
Parameter
Min
fMAXA
-90
-15
Conditions
Max
Min
Max
Min
PT
Aloc
Turbo Slew
Off
Rate
Unit
Maximum
Frequency
External
Feedback
1/(tSA+tCOA)
38.4
26.32
21.27
MHz
Maximum
Frequency
Internal
Feedback
(fCNTA)
1/(tSA+tCOA–10)
62.5
35.71
27.78
MHz
Maximum
Frequency
Pipelined
Data
1/(tCHA+tCLA)
71.4
41.67
35.71
MHz
tSA
Input Setup
Time
7
8
12
tHA
Input Hold
Time
8
12
14
tCHA
Clock Input
High Time
9
12
15
tCLA
Clock Input
Low Time
9
12
tCOA
Clock to
Output Delay
tARDA
CPLD Array
Delay
Any macrocell
tMINA
Minimum
Clock Period
1/fCNTA
16
)
s
(
ct
30
11
16
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
)
s
t(
ns
ns
d
o
r
37
22
39
+ 10
uc
P
e
let
o
s
b
O
28
+2
15
21
u
d
o
84/109
Max
+ 10
ns
+ 10
ns
+ 10
+2
–2
ns
ns
ns
PSD813F2V, PSD854F2V
Table 52. CPLD Macrocell Asynchronous Clock Mode Timing (3V devices)
-12
Symbol
Parameter
Min
fMAXA
-15
-20
Conditions
Max
Min
Max
Min
Max
PT
Aloc
Turbo Slew
Off
Rate
Unit
Maximum
Frequency
External
Feedback
1/(tSA+tCOA)
21.7
19.2
16.9
MHz
Maximum
Frequency
Internal
Feedback
(fCNTA)
1/(tSA+tCOA–10)
27.8
23.8
20.4
MHz
1/(tCHA+tCLA)
33.3
27
24.4
MHz
Maximum
Frequency
Pipelined Data
tSA
Input Setup
Time
10
12
13
tHA
Input Hold Time
12
15
17
tCHA
Clock High
Time
17
22
25
tCLA
Clock Low Time
13
15
16
tCOA
Clock to Output
Delay
tARD
CPLD Array
Delay
tMINA
Minimum Clock
Period
Any macrocell
1/fCNTA
36
)
s
(
ct
36
40
25
29
49
+ 20
ns
)
s
t(
ns
c
u
d
+ 20
46
ro
33
+4
P
e
let
o
s
b
O
42
+4
ns
+ 20
+ 20
ns
–6
ns
ns
ns
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
85/109
PSD813F2V, PSD854F2V
Figure 44. Input Macrocell Timing (product term clock)
t INH
t INL
PT CLOCK
t IS
t IH
INPUT
OUTPUT
t INO
AI03101
Table 53. Input Macrocell Timing (5V devices)
-70
Symbol
Parameter
-90
-15
PT
Aloc
Conditions
Min
Max
Min
Max
Min
tIS
Input Setup Time
(Note 1)
0
0
0
tIH
Input Hold Time
(Note 1)
15
20
26
tINH
NIB Input High Time
(Note 1)
9
12
18
tINL
NIB Input Low Time
(Note 1)
9
12
tINO
NIB Input to Combinatorial
Delay
(Note 1)
Max
ro
18
46
o
s
b
O
-
c
u
d
59
Unit
)
s
t(
+ 10
P
e
let
34
Turbo
Off
ns
ns
ns
ns
+2
+ 10
ns
Note: 1. Inputs from Port A, B, and C relative to register/ latch clock from the PLD. ALE/AS latch timings refer to tAVLX and tLXAX.
Table 54. Input Macrocell Timing (3V devices)
Symbol
Parameter
Min
Max
-15
Min
-20
Max
Min
Max
PT
Aloc
Turbo
Off
0
0
(Note 1)
25
25
30
NIB Input High Time
(Note 1)
12
13
15
ns
NIB Input Low Time
(Note 1)
12
13
15
ns
NIB Input to Combinatorial
Delay
(Note 1)
tIH
Input Hold Time
tINH
tINL
t
e
l
o
r
P
e
u
d
o
46
62
ns
+ 20
70
+4
+ 20
Note: 1. Inputs from Port A, B, and C relative to register/latch clock from the PLD. ALE latch timings refer to tAVLX and tLXAX.
86/109
Unit
0
Input Setup Time
s
b
O
ct
-12
(Note 1)
tIS
tINO
(s)
Conditions
Doc ID 10552 Rev 3
ns
ns
PSD813F2V, PSD854F2V
Figure 45. READ Timing
tAVLX
tLXAX
1
ALE /AS
tLVLX
A /D
MULTIPLEXED
BUS
DATA
VALID
ADDRESS
VALID
tAVQV
ADDRESS
NON-MULTIPLEXED
BUS
ADDRESS
VALID
DATA
NON-MULTIPLEXED
BUS
DATA
VALID
tSLQV
CSI
tRLQV
tRHQX
tRLRH
RD
(PSEN, DS)
tRHQZ
c
u
d
tEHEL
E
tTHEH
o
r
P
tELTL
R/W
e
t
le
tAVPV
ADDRESS OUT
so
)
s
t(
AI02895
b
O
-
Note: 1. tAVLX and tLXAX are not required for 80C251 in Page Mode or 80C51XA in Burst Mode.
)
s
(
ct
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
87/109
PSD813F2V, PSD854F2V
Table 55. READ Timing (5V devices)
-70
Symbol
Parameter
Min
tLVLX
ALE or AS Pulse Width
tAVLX
Address Setup Time
tLXAX
-90
-15
Conditions
Max
Min
Max
Min
Max
Turbo
Off
Unit
15
20
28
ns
(Note 3)
4
6
10
ns
Address Hold Time
(Note 3)
7
8
11
ns
tAVQV
Address Valid to Data Valid
(Note 3)
tSLQV
CS Valid to Data Valid
70
90
150
+ 10
ns
75
100
150
ns
RD to Data Valid 8-Bit Bus
(Note 5)
24
32
40
ns
RD or PSEN to Data Valid
8-Bit Bus, 8031, 80251
(Note 2)
31
38
45
ns
tRHQX
RD Data Hold Time
(Note 1)
0
0
0
tRLRH
RD Pulse Width
(Note 1)
27
32
38
tRHQZ
RD to Data High-Z
(Note 1)
tEHEL
E Pulse Width
27
32
tTHEH
R/W Setup Time to Enable
6
10
tELTL
R/W Hold Time After Enable
0
tAVPV
Address Input Valid to
Address Output Delay
tRLQV
Note: 1.
2.
3.
4.
5.
(Note 4)
25
38
P
e
let
0
20
o
s
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
uc
d
o
r
18
25
)
s
t(
ns
30
RD timing has the same timing as DS, LDS, UDS, and PSEN signals.
RD and PSEN have the same timing.
Any input used to select an internal PSD function.
In multiplexed mode, latched addresses generated from ADIO delay to address output on any Port.
RD timing has the same timing as DS, LDS, and UDS signals.
)
s
(
ct
88/109
20
ns
0
30
ns
ns
ns
ns
ns
PSD813F2V, PSD854F2V
Table 56. READ Timing (3V devices)
-12
Symbol
Parameter
Min
tLVLX
ALE or AS Pulse Width
tAVLX
Address Setup Time
tLXAX
-15
-20
Conditions
Max
Min
Max
Min
Max
Turbo
Off
Unit
26
26
30
ns
(Note 3)
9
10
12
ns
Address Hold Time
(Note 3)
9
12
14
ns
tAVQV
Address Valid to Data Valid
(Note 3)
tSLQV
CS Valid to Data Valid
120
150
200
+ 20
ns
120
150
200
ns
RD to Data Valid 8-Bit Bus
(Note 5)
35
35
40
ns
RD or PSEN to Data Valid 8-Bit Bus,
8031, 80251
(Note 2)
45
50
55
ns
tRHQX
RD Data Hold Time
(Note 1)
tRLRH
RD Pulse Width
tRHQZ
RD to Data High-Z
tEHEL
E Pulse Width
40
45
tTHEH
R/W Setup Time to Enable
15
18
tELTL
R/W Hold Time After Enable
0
tAVPV
Address Input Valid to
Address Output Delay
tRLQV
Note: 1.
2.
3.
4.
5.
0
0
0
38
40
45
(Note 1)
(Note 4)
38
45
c
u
d
52
ro
20
P
e
let
35
)
s
t(
ns
40
0
33
ns
0
ns
ns
ns
ns
40
ns
o
s
b
O
-
RD timing has the same timing as DS, LDS, UDS, and PSEN signals.
RD and PSEN have the same timing for 8031.
Any input used to select an internal PSD function.
In multiplexed mode latched address generated from ADIO delay to address output on any Port.
RD timing has the same timing as DS, LDS, and UDS signals.
)
s
(
ct
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
89/109
PSD813F2V, PSD854F2V
Figure 46. WRITE Timing
tAVLX
t LXAX
ALE/AS
t LVLX
A/D
MULTIPLEXED
BUS
ADDRESS
VALID
DATA
VALID
tAVWL
ADDRESS
NON-MULTIPLEXED
BUS
ADDRESS
VALID
DATA
NON-MULTIPLEXED
BUS
DATA
VALID
tSLWL
CSI
tDVWH
t WHDX
t WLWH
WR
(DS)
t WHAX
t EHEL
c
u
d
E
t THEH
t ELTL
R/ W
t WLMV
e
t
le
tAVPV
o
s
b
O
-
ADDRESS OUT
)
s
(
ct
u
d
o
r
P
e
t
e
l
o
s
b
O
90/109
Doc ID 10552 Rev 3
)
s
t(
o
r
P
t WHPV
STANDARD
MCU I/O OUT
AI02896
PSD813F2V, PSD854F2V
Table 57. WRITE Timing (5V devices)
-70
Symbol
Parameter
ALE or AS Pulse Width
tAVLX
Address Setup Time
tLXAX
Address Hold Time
tAVWL
Address Valid to Leading
Edge of WR
tSLWL
-15
Unit
Min
tLVLX
-90
Conditions
Max
Min
Max
Min
Max
15
20
28
ns
(Note 1)
4
6
10
ns
(Note 1)
7
8
11
ns
(Notes 1,3)
8
15
20
ns
CS Valid to Leading Edge of WR
(Note 3)
12
15
20
ns
tDVWH
WR Data Setup Time
(Note 3)
25
35
45
ns
tWHDX
WR Data Hold Time
(Note 3)
4
5
5
ns
tWLWH
WR Pulse Width
(Note 3)
31
35
45
ns
tWHAX1
Trailing Edge of WR to Address Invalid
(Note 3)
6
8
10
tWHAX2
Trailing Edge of WR to DPLD Address
Invalid
(Note 3,6)
0
0
tWHPV
Trailing Edge of WR to Port Output
Valid Using I/O Port Data Register
tDVMV
Data Valid to Port Output Valid
Using Macrocell Register
Preset/Clear
(Notes 3,5)
tAVPV
Address Input Valid to Address
Output Delay
(Note 2)
tWLMV
WR Valid to Port Output Valid Using
Macrocell Register Preset/Clear
Note: 1.
2.
3.
4.
5.
6.
)
s
(
ct
(Note 3)
b
O
-
d
o
r
27
30
ns
ns
38
ns
P
e
let
42
55
65
ns
20
25
30
ns
48
55
65
ns
so
(Notes 3,4)
uc
0
)
s
t(
Any input used to select an internal PSD function.
In multiplexed mode, latched address generated from ADIO delay to address output on any port.
WR has the same timing as E, LDS, UDS, WRL, and WRH signals.
Assuming data is stable before active WRITE signal.
Assuming WRITE is active before data becomes valid.
TWHAX2 is the address hold time for DPLD inputs that are used to generate Sector Select signals for internal PSD memory.
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
91/109
PSD813F2V, PSD854F2V
Table 58. WRITE Timing (3V devices)
-12
Symbol
Parameter
ALE or AS Pulse Width
tAVLX
Address Setup Time
tLXAX
Address Hold Time
tAVWL
Address Valid to Leading
Edge of WR
tSLWL
-20
Unit
Min
tLVLX
-15
Conditions
Max
Min
Max
Min
Max
26
26
30
(Note 1)
9
10
12
ns
(Note 1)
9
12
14
ns
(Notes 1,3)
17
20
25
ns
CS Valid to Leading Edge of WR
(Note 3)
17
20
25
ns
tDVWH
WR Data Setup Time
(Note 3)
45
45
50
ns
tWHDX
WR Data Hold Time
(Note 3)
7
8
10
ns
tWLWH
WR Pulse Width
(Note 3)
46
48
53
ns
tWHAX1
Trailing Edge of WR to Address Invalid
(Note 3)
10
12
17
tWHAX2
Trailing Edge of WR to DPLD Address
Invalid
(Note 3,6)
0
0
tWHPV
Trailing Edge of WR to Port Output
Valid Using I/O Port Data Register
tDVMV
Data Valid to Port Output Valid
Using Macrocell Register Preset/Clear
tAVPV
Address Input Valid to Address
Output Delay
tWLMV
WR Valid to Port Output Valid Using
Macrocell Register Preset/Clear
Note: 1.
2.
3.
4.
5.
6.
(Note 3)
(Note 2)
d
o
r
33
35
o
s
b
O
-
ns
ns
70
80
ns
33
35
40
ns
70
70
80
ns
70
(Notes 3,4)
ns
40
P
e
let
(Notes 3,5)
uc
0
)
s
t(
Any input used to select an internal PSD function.
In multiplexed mode, latched address generated from ADIO delay to address output on any port.
WR has the same timing as E, LDS, UDS, WRL, and WRH signals.
Assuming data is stable before active WRITE signal.
Assuming WRITE is active before data becomes valid.
TWHAX2 is the address hold time for DPLD inputs that are used to generate Sector Select signals for internal PSD memory.
)
s
(
ct
u
d
o
Table 59. Program, WRITE and Erase Times (5V devices)
r
P
e
Symbol
Parameter
Min.
Flash Program
t
e
l
o
s
b
O
tWHQV3
Typ.
8.5
1
Flash Bulk Erase (pre-programmed)
3
Flash Bulk Erase (not pre-programmed)
5
Sector Erase (pre-programmed)
1
tWHQV2
Sector Erase (not pre-programmed)
2.2
tWHQV1
Byte Program
14
Program / Erase Cycles (per Sector)
tWHWLO
Sector Erase Time-Out
tQ7VQV
DQ7 Valid to Output (DQ7-DQ0) Valid (Data Polling)2
30
s
s
30
s
s
1200
µs
cycles
100
Doc ID 10552 Rev 3
Unit
s
100,000
Note: 1. Programmed to all zero before erase.
2. The polling status, DQ7, is valid tQ7VQV time units before the data byte, DQ0-DQ7, is valid for reading.
92/109
Max.
µs
30
ns
PSD813F2V, PSD854F2V
Table 60. Program, WRITE and Erase Times (3V devices)
Symbol
Parameter
Min.
Flash Program
Typ.
Max.
8.5
Flash Bulk Erase1 (pre-programmed)
3
Flash Bulk Erase (not pre-programmed)
5
tWHQV3
Sector Erase (pre-programmed)
1
tWHQV2
Sector Erase (not pre-programmed)
2.2
tWHQV1
Byte Program
14
Program / Erase Cycles (per Sector)
s
30
Sector Erase Time-Out
tQ7VQV
DQ7 Valid to Output (DQ7-DQ0) Valid (Data Polling)2
s
s
30
s
s
1200
100,000
tWHWLO
Unit
µs
cycles
100
µs
30
ns
Note: 1. Programmed to all zero before erase.
2. The polling status, DQ7, is valid tQ7VQV time units before the data byte, DQ0-DQ7, is valid for reading.
c
u
d
e
t
le
)
s
(
ct
)
s
t(
o
r
P
o
s
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
93/109
PSD813F2V, PSD854F2V
Figure 47. Peripheral I/O READ Timing
ALE/AS
ADDRESS
A/D BUS
DATA VALID
tAVQV (PA)
tSLQV (PA)
CSI
tRLQV (PA)
tQXRH (PA)
tRHQZ (PA)
tRLRH (PA)
RD
tDVQV (PA)
DATA ON PORT A
AI02897
Table 61. Port A Peripheral Data Mode READ Timing (5V devices)
-70
Symbol
Parameter
Address Valid to Data
Valid
tSLQV–PA
CSI Valid to Data Valid
(Note 3)
RD to Data Valid 8031 Mode
tDVQV–PA
Data In to Data Out Valid
tQXRH–PA
RD Data Hold Time
tRLRH–PA
RD Pulse Width
tRHQZ–PA
RD to Data High-Z
o
r
P
e
c
u
d
(t s)
(Note 1)
(Note 1)
t
e
l
o
s
b
O
94/109
Doc ID 10552 Rev 3
-15
Turbo
Off
Unit
39
45
+ 10
ns
27
35
45
+ 10
ns
21
32
40
ns
32
38
45
ns
22
30
38
ns
Max
Min
e
t
le
37
so
b
O
-
(Notes 1,4)
RD to Data Valid
tRLQV–PA
o
r
P
Max
Conditions
Min
tAVQV–PA
-90
c
u
d
)
s
t(
Max
Min
0
0
0
ns
27
32
38
ns
23
25
30
ns
PSD813F2V, PSD854F2V
Table 62. Port A Peripheral Data Mode READ Timing (3V devices)
-12
Symbol
Parameter
-15
-20
Turbo
Off
Unit
Max
Conditions
Min
tAVQV–PA
Address Valid to Data Valid
tSLQV–PA
CSI Valid to Data Valid
(Note 3)
Max
Min
Max
Min
50
50
50
+ 20
ns
37
45
50
+ 20
ns
37
40
45
ns
RD to Data Valid 8031 Mode
45
45
50
ns
tDVQV–PA
Data In to Data Out Valid
38
40
45
ns
tQXRH–PA
RD Data Hold Time
tRLRH–PA
RD Pulse Width
(Note 1)
tRHQZ–PA
RD to Data High-Z
(Note 1)
tRLQV–PA
(Notes 1,4)
RD to Data Valid
0
0
0
ns
36
36
46
ns
36
40
45
ns
Figure 48. Peripheral I/O WRITE Timing
c
u
d
ALE/AS
ADDRESS
A / D BUS
DATA OUT
tWLQV
WR
e
t
le
(PA)
o
s
b
O
-
)
s
t(
o
r
P
tWHQZ (PA)
tDVQV (PA)
(s)
PORT A
DATA OUT
AI02898
t
c
u
Table 63. Port A Peripheral Data Mode WRITE Timing (5V devices)
d
o
r
P
e
Symbol
-70
Parameter
t
e
l
o
-90
-15
Conditions
Unit
Min
Max
Min
Max
Min
Max
tWLQV–PA
WR to Data Propagation Delay
(Note 2)
25
35
40
ns
tDVQV–PA
Data to Port A Data Propagation Delay
(Note 5)
22
30
38
ns
WR Invalid to Port A Tri-state
(Note 2)
20
25
33
ns
bs
tWHQZ–PA
O
Note: 1.
2.
3.
4.
5.
RD has the same timing as DS, LDS, UDS, and PSEN (in 8031 combined mode).
WR has the same timing as the E, LDS, UDS, WRL, and WRH signals.
Any input used to select Port A Data Peripheral mode.
Data is already stable on Port A.
Data stable on ADIO pins to data on Port A.
Doc ID 10552 Rev 3
95/109
PSD813F2V, PSD854F2V
Table 64. Port A Peripheral Data Mode WRITE Timing (3V devices)
-12
Symbol
Parameter
-15
-20
Conditions
Unit
Min
Max
Min
Max
Min
Max
tWLQV–PA
WR to Data Propagation Delay
(Note 2)
42
45
55
ns
tDVQV–PA
Data to Port A Data Propagation Delay
(Note 5)
38
40
45
ns
tWHQZ–PA
WR Invalid to Port A Tri-state
(Note 2)
33
33
35
ns
Note: 1.
2.
3.
4.
5.
RD has the same timing as DS, LDS, UDS, and PSEN (in 8031 combined mode).
WR has the same timing as the E, LDS, UDS, WRL, and WRH signals.
Any input used to select Port A Data Peripheral mode.
Data is already stable on Port A.
Data stable on ADIO pins to data on Port A.
Figure 49. Reset (RESET) Timing
VCC(min)
VCC
tNLNH-PO
Power-On Reset
tNLNH
tOPR
tNLNH-A
Warm Reset
Table 65. Reset (RESET) Timing (5V devices)
Parameter
P
e
let
o
s
b
O
-
Conditions
1
tNLNH
RESET Active Low Time
tNLNH–PO
Power On Reset Active Low Time
tNLNH–A
Warm Reset (on the PSD834Fx) 2
tOPR
RESET High to Operational Device
(s)
ct
o
r
P
e
tOPR
d
o
r
RESET
Symbol
uc
du
Min
)
s
t(
AI02866b
Max
Unit
150
ns
1
ms
25
μs
120
ns
Max
Unit
Note: 1. Reset (RESET) does not reset Flash memory Program or Erase cycles.
2. Warm reset aborts Flash memory Program or Erase cycles, and puts the device in READ Mode.
Table 66. Reset (RESET) Timing (3V devices)
t
e
l
o
Symbol
bs
tNLNH
Parameter
Conditions
RESET Active Low Time 1
Min
300
ns
tNLNH–PO
Power On Reset Active Low Time
1
ms
tNLNH–A
Warm Reset (on the PSD834Fx) 2
25
μs
tOPR
RESET High to Operational Device
O
Note: 1. Reset (RESET) does not reset Flash memory Program or Erase cycles.
2. Warm reset aborts Flash memory Program or Erase cycles, and puts the device in READ Mode.
96/109
Doc ID 10552 Rev 3
300
ns
PSD813F2V, PSD854F2V
Figure 50. ISC Timing
t ISCCH
TCK
t ISCCL
t ISCPSU
t ISCPH
TDI/TMS
t ISCPZV
t ISCPCO
ISC OUTPUTS/TDO
t ISCPVZ
ISC OUTPUTS/TDO
c
u
d
)
s
t(
AI02865
Table 67. ISC Timing (5V devices)
e
t
le
-70
Symbol
Parameter
Conditions
o
s
b
O
-
Min
Max
o
r
P
-90
Min
Max
-15
Unit
Min
Max
tISCCF
Clock (TCK, PC1) Frequency (except for
PLD)
tISCCH
Clock (TCK, PC1) High Time (except for
PLD)
tISCCL
Clock (TCK, PC1) Low Time (except for
PLD)
tISCCFP
Clock (TCK, PC1) Frequency (PLD only)
(Note 2)
tISCCHP
Clock (TCK, PC1) High Time (PLD only)
(Note 2)
240
240
240
ns
tISCCLP
Clock (TCK, PC1) Low Time (PLD only)
(Note 2)
240
240
240
ns
ISC Port Set Up Time
7
8
10
ns
ISC Port Hold Up Time
5
5
5
ns
od
r
P
e
tISCPH
bs
20
18
14
MHz
(Note 1)
23
26
31
ns
(Note 1)
23
26
31
ns
t
e
l
o
tISCPSU
tISCPCO
uc
(t s)
(Note 1)
2
2
2
MHz
ISC Port Clock to Output
21
23
25
ns
tISCPZV
ISC Port High-Impedance to Valid Output
21
23
25
ns
tISCPVZ
ISC Port Valid Output to
High-Impedance
21
23
25
ns
O
Note: 1. For non-PLD Programming, Erase or in ISC by-pass mode.
2. For Program or Erase PLD only.
Doc ID 10552 Rev 3
97/109
PSD813F2V, PSD854F2V
Table 68. ISC Timing (3V devices)
-12
Symbol
Parameter
-15
-20
Conditions
Unit
Min
Max
Min
Max
Min
Max
tISCCF
Clock (TCK, PC1) Frequency (except for
PLD)
(Note 1)
tISCCH
Clock (TCK, PC1) High Time (except for
PLD)
(Note 1)
40
45
51
ns
tISCCL
Clock (TCK, PC1) Low Time (except for
PLD)
(Note 1)
40
45
51
ns
tISCCFP
Clock (TCK, PC1) Frequency (PLD only)
(Note 2)
tISCCHP
Clock (TCK, PC1) High Time (PLD only)
(Note 2)
240
240
240
ns
tISCCLP
Clock (TCK, PC1) Low Time (PLD only)
(Note 2)
240
240
240
ns
tISCPSU
ISC Port Set Up Time
12
13
15
ns
tISCPH
ISC Port Hold Up Time
5
5
5
tISCPCO
ISC Port Clock to Output
30
36
tISCPZV
ISC Port High-Impedance to Valid Output
30
36
tISCPVZ
ISC Port Valid Output to
High-Impedance
30
12
2
Note: 1. For non-PLD Programming, Erase or in ISC by-pass mode.
2. For Program or Erase PLD only.
Table 69. Power-down Timing (5V devices)
Symbol
Parameter
o
s
b
O
-
e
t
le
-70
9
2
2
ALE Access Time from Power-down
tCLWH
Maximum Delay from
APD Enable to Internal PDN Valid
Signal
)
s
(
ct
u
d
o
r
P
e
MHz
ns
c
u
d
o
r
P
36
-90
MHz
)
s
t(
40
ns
40
ns
40
ns
-15
Conditions
tLVDV
Note: 1. tCLCL is the period of CLKIN (PD1).
10
Unit
Min
Max
Min
Max
80
Using CLKIN
(PD1)
Min
90
Max
150
15 * tCLCL1
ns
µs
Table 70. Power-down Timing (3V devices)
t
e
l
o
Symbol
s
b
O
tLVDV
tCLWH
-12
Parameter
-20
Unit
Min
ALE Access Time from Power-down
Maximum Delay from APD Enable to
Internal PDN Valid Signal
Max
145
Using CLKIN
(PD1)
Note: 1. tCLCL is the period of CLKIN (PD1).
98/109
-15
Conditions
Doc ID 10552 Rev 3
Min
Max
150
15 * tCLCL1
Min
Max
200
ns
µs
PSD813F2V, PSD854F2V
PACKAGE MECHANICAL
In order to meet environmental requirements, ST
offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance.
ECOPACK® specifications, grade definitions and
product status are available at: www.st.com. ECOPACK® is an ST trademark.
Figure 51. PQFP52 - 52-pin Plastic, Quad, Flat Package Mechanical Drawing
D
D1
D2
A2
e
E2 E1 E
Ne
c
u
d
N
1
e
t
le
Nd
)
s
(
ct
o
s
b
O
-
u
d
o
QFP-A
)
s
t(
b
o
r
P
A
CP
L1
c
A1
α
L
r
P
e
Note: Drawing is not to scale.
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
99/109
PSD813F2V, PSD854F2V
Table 71. PQFP52 - 52-pin Plastic, Quad, Flat Package Mechanical Dimensions
mm
inches
Symb.
Typ.
Min.
Max.
Min.
Max.
A
2.35
0.093
A1
0.25
0.010
A2
2.00
1.80
2.10
0.077
0.083
b
0.22
0.38
0.009
0.015
c
0.11
0.23
0.004
0.009
0.079
D
13.20
13.15
13.25
0.520
0.518
0.522
D1
10.00
9.95
10.05
0.394
0.392
0.396
D2
7.80
–
–
0.307
–
–
E
13.20
13.15
13.25
0.520
0.518
0.522
E1
10.00
9.95
10.05
0.394
0.392
E2
7.80
–
–
0.307
–
e
0.65
–
–
0.026
)
s
t(
L
0.88
0.73
1.03
0.035
L1
1.60
–
–
0.063
α
0°
7°
N
52
Nd
13
Ne
13
e
t
le
so
CP
b
O
0.10
)
s
(
ct
u
d
o
r
P
e
t
e
l
o
s
b
O
100/109
Typ.
Doc ID 10552 Rev 3
0.396
–
c
u
d
0.029
0.041
0°
7°
o
r
P
52
13
13
0.004
PSD813F2V, PSD854F2V
Figure 52. PLCC52 - 52-lead Plastic Lead, Chip Carrier Package Mechanical Drawing
D
D1
A1
A2
M
M1
1 N
b1
e
D2/E2 D3/E3
E1 E
b
L1
L
C
A
c
u
d
CP
PLCC-B
Note: Drawing is not to scale.
)
s
t(
o
r
P
Table 72. PLCC52 - 52-lead Plastic Lead, Chip Carrier Package Mechanical Dimensions
e
t
le
mm
Symbol
Typ.
Min.
A
4.19
A1
2.54
A2
–
Min.
Max.
0.165
0.180
0.100
0.110
0.91
–
0.036
0.53
0.013
0.021
b
O
4.57
2.79
)
s
(
ct
Typ.
B
0.33
B1
0.66
0.81
0.026
0.032
0.246
0.261
0.0097
0.0103
19.94
20.19
0.785
0.795
19.05
19.15
0.750
0.754
17.53
18.54
0.690
0.730
E
19.94
20.19
0.785
0.795
E1
19.05
19.15
0.750
0.754
E2
17.53
18.54
0.690
0.730
u
d
o
C
r
P
e
D
D1
t
e
l
o
D2
bs
O
so
Max.
inches
e
1.27
–
–
0.050
–
–
R
0.89
–
–
0.035
–
–
N
52
52
Nd
13
13
Ne
13
13
Doc ID 10552 Rev 3
101/109
PSD813F2V, PSD854F2V
Figure 53. TQFP64 - 64-lead Thin Quad Flatpack, Package Outline
D
D1
D2
A2
e
E2 E1 E
Ne
b
N
1
c
u
d
A
Nd
ro
L1
P
e
let
QFP-A
)
s
(
ct
Note: Drawing is not to scale.
o
s
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
102/109
Doc ID 10552 Rev 3
A1
α
CP
c
L
)
s
t(
PSD813F2V, PSD854F2V
Table 73. TQFP64 - 64-lead Thin Quad Flatpack, Package Mechanical Data
mm
inches
Symb.
Typ.
A
Min.
Max.
1.42
1.54
Typ.
Min.
Max.
0.056
0.061
A1
0.10
0.07
0.14
0.004
0.003
0.005
A2
1.40
1.36
1.44
0.055
0.054
0.057
α
3.5°
0.0°
7.0°
3.5°
0.0°
7.0°
b
0.35
0.33
0.38
0.014
0.013
0.015
c
0.17
0.006
D
16.00
15.90
16.10
0.630
0.626
0.634
D1
14.00
13.98
14.03
0.551
0.550
0.552
D2
12.00
11.95
12.05
0.472
0.470
0.474
E
16.00
15.90
16.10
0.630
0.626
E1
14.00
13.98
14.03
0.551
0.550
E2
12.00
11.95
12.05
0.472
0.470
)
s
t(
e
0.80
0.75
0.85
0.031
0.030
L
0.60
0.45
0.75
0.024
L1
1.00
0.94
1.06
0.039
CP
0.10
e
t
le
Pr
0.634
0.552
od
uc
0.474
0.033
0.018
0.030
0.037
0.042
0.004
N
64
Nd
16
Ne
16
so
)
s
(
ct
b
O
-
64
16
16
u
d
o
r
P
e
t
e
l
o
s
b
O
Doc ID 10552 Rev 3
103/109
PSD813F2V, PSD854F2V
PART NUMBERING
Table 74. Ordering Information Scheme
Example:
PSD8
1
3
F
2
V
–
15
J
1
T
Device Type
PSD8 = 8-bit PSD with Register Logic
PSD9 = 8-bit PSD with Combinatorial Logic
SRAM Capacity
1 = 16 Kbit
5 = 256 Kbit
Flash Memory Capacity
3 = 1 Mbit (128K x 8)
4 = 2 Mbit (256K x 8)
2nd Flash Memory
2 = 256 Kbit Flash memory + SRAM
c
u
d
Operating Voltage
V = VCC = 3.0 to 3.6V
e
t
le
Speed
70 = 70ns
90 = 90ns
12 = 120ns
15 = 150ns
20 = 200ns
Package
J = ECOPACK PLCC52
M = ECOPACK PQFP52
U = ECOPACK TQFP64
)
s
(
ct
)
s
t(
o
r
P
o
s
b
O
-
u
d
o
r
P
e
Temperature Range
blank = 0 to 70°C (commercial)
1 = –40 to 85°C (industrial)
t
e
l
o
s
b
O
Option
T = Tape & Reel Packing
For a list of available options (e.g., speed, package) or for further information on any aspect of this device,
please contact your nearest ST Sales Office.
104/109
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
APPENDIX A. PQFP52 PIN ASSIGNMENTS
Table 75. PQFP52 Connections (Figure 2)
Pin Number
Pin Assignments
Pin Number
Pin Assignments
1
PD2
27
AD4
2
PD1
28
AD5
3
PD0
29
AD6
4
PC7
30
AD7
5
PC6
31
VCC
6
PC5
32
AD8
7
PC4
33
AD9
8
VCC
34
AD10
9
GND
35
AD11
10
PC3
36
AD12
11
PC2
37
12
PC1
38
13
PC0
39
14
PA7
40
15
PA6
16
PA5
17
PA4
18
PA3
19
GND
20
PA2
21
c
u
d
22
o
r
P
e
23
24
t
e
l
o
25
26
e
t
le
41
c
u
d
)
s
t(
AD13
AD14
o
r
P
AD15
CNTL0
RESET
42
CNTL2
43
CNTL1
44
PB7
45
PB6
46
GND
PA1
47
PB5
PA0
48
PB4
AD0
49
PB3
AD1
50
PB2
AD2
51
PB1
AD3
52
PB0
(t s)
o
s
b
O
-
s
b
O
Doc ID 10552 Rev 3
105/109
PSD813F2V, PSD854F2V
APPENDIX B. PLCC52 PIN ASSIGNMENTS
Table 76. PLCC52 Connections (Figure 3)
Pin Number
Pin Assignments
Pin Number
Pin Assignments
1
GND
27
PA2
2
PB5
28
PA1
3
PB4
29
PA0
4
PB3
30
AD0
5
PB2
31
AD1
6
PB1
32
AD2
7
PB0
33
AD3
8
PD2
34
AD4
9
PD1
35
AD5
10
PD0
36
AD6
11
PC7
37
12
PC6
38
13
PC5
39
c
u
d
14
PC4
40
15
VCC
16
GND
17
PC3
18
PC2
19
PC1
20
PC0
21
c
u
d
22
o
r
P
e
23
24
t
e
l
o
25
26
e
t
le
41
AD7
VCC
o
r
P
AD8
AD9
AD10
42
AD11
43
AD12
44
AD13
45
AD14
46
AD15
PA7
47
CNTL0
PA6
48
RESET
PA5
49
CNTL2
PA4
50
CNTL1
PA3
51
PB7
GND
52
PB6
(t s)
o
s
b
O
-
s
b
O
106/109
)
s
t(
Doc ID 10552 Rev 3
PSD813F2V, PSD854F2V
APPENDIX C. TQFP64 PIN ASSIGNMENTS
Table 77. TQFP64 Connections (Figure 4)
Pin Number
Pin Assignments
Pin Number
Pin Assignments
1
PD2
33
AD3
2
PD1
34
AD4
3
PD0
35
AD5
4
PC7
36
AD6
5
PC6
37
AD7
6
PC5
38
VCC
7
VCC
39
VCC
8
VCC
40
AD8
9
VCC
41
AD9
10
GND
42
AD10
11
GND
43
12
PC3
44
13
PC2
45
14
PC1
46
15
PC0
16
NC
17
NC
18
NC
19
PA7
20
PA6
21
uc
AD12
o
r
P
AD13
AD14
AD15
CNTL0
49
NC
50
RESET
51
CNTL2
52
CNTL1
PA5
53
PB7
PA4
54
PB6
PA3
55
GND
GND
56
GND
GND
57
PB5
PA2
58
PB4
27
PA1
59
PB3
28
PA0
60
PB2
29
AD0
61
PB1
30
AD1
62
PB0
31
N/D
63
NC
32
AD2
64
NC
od
r
P
e
23
24
t
e
l
o
25
26
O
AD11
48
22
bs
e
t
le
47
c
u
d
)
s
t(
so
(t s)
b
O
-
Doc ID 10552 Rev 3
107/109
PSD813F2V, PSD854F2V
REVISION HISTORY
Table 78. Document Revision History
Date
Version
04-Jun-04
1.0
Description of Revision
First Edition (3V split from original)
12-Feb-2009
2
Removed PSD853F2V and PSD833F2V root part numbers.
Updated Table 1 to remove PSD813F3, PSD813F4, PSD833F2, PSD834F2, and
PSD853F2. Updated Table 74 to remove options not mentioned in the datasheet.
Updated voltage range in title.
Added ECOPACK text in cover page and in section PACKAGE MECHANICAL.
Updated datasheet status to “not for new design”.
Backup battery feature removed: updated FEATURES SUMMARY, Table 2 (pins PC2 and
PC4 configurations ), SUMMARY DESCRIPTION, PSD Block Diagram figure, Memory
section, SRAM section, Port C – Functionality and Structure section. Removed SRAM
standby mode in POWER MANAGEMENT. Updated PC2 in Table 76. Removed VSTBY,
ISTBY, VOH1, VDF, and IIDLE from Table 45 and Table 46. Removed VSTBYON timings tables.
Updated disclaimer text.
05-May-2009
3
Updated disclaimer on last page.
Corrected pin 7 of TQFP64 package in Figure 4.TQFP64 Connections.
Updated Figure 5.PSD Block Diagram.
c
u
d
e
t
le
)
s
(
ct
o
s
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
108/109
Doc ID 10552 Rev 3
o
r
P
)
s
t(
PSD813F2V, PSD854F2V
c
u
d
Please Read Carefully:
)
s
t(
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
e
t
le
o
r
P
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
o
s
b
O
-
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
)
s
(
ct
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
u
d
o
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE
SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN
PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT
SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
r
P
e
t
e
l
o
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
s
b
O
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2009 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 10552 Rev 3
109/109