EXTERNAL PUP 120 Series 1 2 0 W AT T S S I N G L E O U T P U T A C / D C G E N E R A L Features • High Efficiency. • Low ripple and noise. • Short circuit protection. • Overvoltage protection. • Over power protection. • Over temperature protection. • 100% burn-in at full rated load. • Standby consumption less than 0.75W. • MEPS compliance. Specifications OPERATING INPUT Input voltage 90-264Vac. Frequency 47Hz–63Hz Input current 1.60A @ 115V, 0.8A @ 230V Leakage current 0.4mA max. @ 115Vac. 60Hz. 0.8mA max. @ 230Vac. 50Hz. Isolation Input – Output: 3000Vac Input – Ground: 1500Vac Output – Ground: 500Vac Inrush current 60A @ 115V, 120A @ 230V OUTPUT 266 MTBF 100,000 hrs @ 25°C. Efficiency 80-86% minimum. Power factor 0.98 typical at 115Vac. ENVIRONMENTAL Operating temperature 0°C to 40°C. Storage temperature -20°C to 85°C Relative humidity 10%–95% non-condensing STANDARDS AND APPROVALS Safety UL60950-1, CSA C22.2 No. 60950, Nemko EN60950: 2000. C-Tick AS/NZS CISPR11 Group 1 Class A EMC standards EN55024, EN55022-B, FCC-B, VCCI-B, EN61000-32, -3, EN61000-4-2, -3, -4, -5, -6, -8, -11. Output voltage See table Output current See table Ripple & noise 1% peak to peak Line regulation ±0.5% maximum at full load. MECHANICAL Load regulation See table Dimensions 167x65x37mm Transient response Max. deviation 4% recovering to 1% within 500µs after 25% load charge Weight 0.62kgs approx. Overvoltage protection Provided on V1 only. Set at 110%–140% of nominal. Overcurrent protection All outputs protected for short circuit conditions Temperature coefficient All outputs ±0.04% per °C. Holdup time Typically 15ms at 110VAC. EXTERNAL PUP 120 Series 1 2 0 W AT T S S I N G L E O U T P U T A C / D C G E N E R A L Selection Table MAX. MODEL OUTPUT #1 OUTPUT NUMBER VNOM IMIN IMAX TOL POWER PUP120-12 12V 0A 8.0A 5% 96W PUP120-13 15V 0A 7.0A 5% 105W PUP120-13-1 18V 0A 6.67A 5% 120W PUP120-13-2 19V 0A 6.32A 5% 120W PUP120-13-3 20V 0A 6.0A 5% 120W PUP120-14 24V 0A 5.0A 5% 120W PUP120-16 30V 0A 4.0A 5% 120W PUP120-17 36V 0A 3.34A 5% 120W PUP120-18 48V 0A 2.5A 5% 120W NOTES: Ripple and noise : Peak-to-peak with 20MHz bandwidth and 10μF tantalum capacitor in paralllel with a 0.1μF ceramic capacitor at rated line voltage and load ranges. Pin Chart MODEL/PIN PUP120-12 PUP120-13 PUP120-13-1 PUP120-13-2 PUP120-13-3 PUP120-14 PUP120-16 PUP120-17 PUP120-18 1 2 3 4 SHELL OF CONNECTOR Return Output +V Return Output +V Return Technical Illustrations Your dependable power partner – www.powerbox.com.au 267