AC-DC 175 Watts xppower.com RCL175 Series • 200 W Peak Rating • Up to 120 W Convection-cooled • Industrial and Medical Approvals • Low Leakage Current • Class I & Class II Applications • Flexible Design for Modified Standards • Connector & Mechanical Options Specification Input Input Voltage Input Frequency Input Current • 85-264 VAC (120-370 VDC) See note 3 • 47-63 Hz • 2.1 A max at 115 VAC 0.9 A max at 230 VAC Inrush Current • 17 A max at 115 VAC, 35 A max at 230 VAC, cold start at +25 °C Power Factor • Complies with EN61000-3-2 for Class A equipment Earth Leakage Current • 120 µA max at 115 VAC 200 µA max at 230 VAC Input Protection • 3.15 A line and neutral fused Output Output Voltage Output Voltage Trim • See models and ratings table • ±10% output 1 via pot, outputs 2-4 track by same percentage Initial Set Accuracy • ±2% of nominal at 50% load Minimum Load • See models & ratings table Start Up Delay • <2 s Start Up Rise Time • <100 ms Hold Up Time • 20 ms min at nominal low line & maximum power Drift • <±0.2% after 20 mins warm up Line Regulation • ±0.5% of nominal over full input range Load Regulation • PQ42 & 43: V1 & V2 ±3%, V3 & V4 ±5% of nominal, all other models: V1 ±1%, V2, V3 & V4 ±5% of nominal Transient Response • 4% max deviation, recovery to within 1% in 500 µs for a 25% load change at 1 A/µs Ripple & Noise • 50 mV (Vo=<5 V), 120mV (Vo=12, 15 V), 200 mV (Vo=24, 48 V). Measured pk-pk with a 20 MHz bandwidth Overvoltage Protection • 115-140% - V1 only. Cycle mains to reset Overtemperature • Fitted with auto restart Protection Overload Protection • 110-125% - Primary side power limiting with auto recovery. Constant current limit for single output models and foldback current limit for multi output models. V3 & V4 PTC resetting fuses Temperature • 0.02%/°C Coefficient General Efficiency Isolation Switching Frequency Signals Remote Sense Remote On/Off MTBF • 80-90% depending on model • 4000 VAC Input to Output 1500 VAC Input to Ground 1500 VAC Output to Ground open frame (For BF applications, consult sales office) 500 VAC Output to Ground U channel & covered • PFC 75 kHz typical, PWM 60 kHz typical • Power fail - open collector output referenced to 0 V sense • See Application Notes • See Application Notes • 385 kHrs typical at +25 °C per MIL-HDBK-217F Environmental Operating Temperature • -10 °C to +50 °C at full power, derate to 50% power at +70 °C Operating Humidity • 5-95% RH, non-condensing Storage Temperature • -20 °C to +85 °C Operating Altitude • 3000m Shock • 30 g peak, half sine, 6 axes Vibration • 2 g rms, 5-500 Hz, 3 axes EMC & Safety Emissions Harmonic Currents Voltage Flicker ESD Immunity Radiated Immunity EFT/Burst Surge Conducted Immunity Dips & Interruptions Safety Approvals • EN55011/22 class B conducted, class A radiated • EN61000-3-2 for class A equipment • EN61000-3-3 • EN61000-4-2, Level 3 Perf Criteria A • EN61000-4-3, 10 V rms 80% mod, Perf Criteria A • EN61000-4-4, Level 3 Perf Criteria A • EN61000-4-5, Level 3 Perf Criteria A • EN61000-4-6, Level 3 Perf Criteria A • EN61000-4-11, 30% 10 ms, 60% 100 ms, 100% 5000 ms, Perf Criteria A, B, B • EN60601-1-1, EN60950-1:2001, UL/cUL60950:2003, CSA60601.1, UL60601-1:2003. Total Power Output 2(6) Output 1 Model Number 175 W 204 W 120 W 12.0 V 0.0 A 14.5 A 17.0 A RCL175PS12 175 W 195 W 120 W 15.0 V 0.0 A 11.6 A 13.0 A RCL175PS15 175 W 200 W 120 W 24.0 V 0.0 A 7.2 A 8.3 A RCL175PS24 175 W 200 W 120 W 28.0 V 0.0 A 6.2 A 7.1 A RCL175PS28 175 W 202 W 120 W 48.0 V 0.0 A 3.6 A 4.2 A 175 W 200 W 110 W 5.0 V 1.5 A 15.0 A - 12.0 V 0.1 A 8.3 A 10.4 A 175 W 200 W 110 W 5.0 V 1.5 A 15.0 A - 12.0 V 0.1 A 6.3 A 8.4 A F 12 V 0.1 A 2.0 A 175 W 200 W 110 W 5.0 V 1.5 A 15.0 A - 15.0 V 0.1 A 4.6 A 6.6 A F 15 V 0.1 A 2.0 A 175 W 200 W 90 W 5.0 V 1.5 A 15.0 A - 3.3 V 0.1 A 15.0 A F 15 V 0.1 A 2.0 A F 15 V 0.1 A 2.0 A RCL175PQ43(5,6) 175 W 200 W 90 W 5.0 V 1.5 A 15.0 A - 12.0 V 0.1 A 5.5 A 7.6 A F5V 0.1 A 2.0 A F 12 V 0.1 A 2.0 A RCL175PQ44(6) 175 W 200 W 90 W 5.0 V 1.5 A 15.0 A - 15.0 V 0.1 A 4.0 A 6.0 A F5V 0.1 A 2.0 A F 15 V 0.1 A 2.0 A RCL175PQ45(4,6) 175 W 200 W 90 W 5.0 V 1.5 A 15.0 A - 24.0 V 0.1 A 3.2 A 5.0 A F 12 V 0.1 A 2.0 A F 12 V 0.1 A 2.0 A RCL175PQ46(4,6) 175 W 200 W 90 W 5.0 V 1.5 A 15.0 A - 24.0 V 0.1 A 3.0 A 5.0 A F 15 V 0.1 A 2.0 A F 15 V 0.1 A 2.0 A RCL175PQ47(4,6) Min Max V Min Peak(1) Output 4(6,8) Peak Conv.(4,5) V Peak(1) Output 3(6,8) Max(7) Max V Min Max V Min Max RCL175PS48 - RCL175PD22(4,6) RCL175PT31(4,6) RCL175PT32(4,6) Notes 1. Peak rating can be taken for 5 seconds in every minute. Average power not to exceed maximum power. 2. There is a user-accessible fan supply rated at 12 V at 350 mA (not available on fan-cooled units). 3. For operation at 85 VAC output power is derated to 95%. 4. Output 1 10 A max convection-cooled. 5. 20 A max from output 1 and 2 combined convection-cooled. Pin Connectors Pin 1 2 3 INPUT CONNECTOR - P1 Function Live N/C Neutral P1 is a 3-way 0.156" pitch square pin header Molex housing 09-91-0300 pins 08-50-0106 (24-18 AWG) 08-50-0108 (28-22 AWG) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 OUTPUT CONNECTOR - P2 Function +Output 1 +Output 1 +Output 1 0V 0V 0V 0V 0V 0V +Output 2 +Output 2 +Output 2 -Output 3 +Output 3 -Output 4 +Output 4 Pin 1 2 3 4 5 6 SIGNALS CONNECTOR - P3 Function Remote On/Off +Sense -Sense PF signal 0 V fan supply +12 V fan supply P3 is a 6-way 0.1" pitch square pin header Molex housing 22-01-2065 pins 08-50-0032 6. A minimum load of 100 mA is required on output 2, 3 and 4 to maintain the regulation figures. 7. 12 CFM airflow required for maximum power. 8. Outputs 3 & 4 are floating, they can be connected externally for positive or negative output. 9. Connector kits and cable harnesses available. Consult sales for options. Application Notes Remote Sense - V1 only, compensates for 0.5 V or 10% whichever is lower. Power Fail - Open collector output refers to 0 V sense (when using the power fail signal, -Sense must be connected to 0 V). Remote On/Off - Connect pin 1 (P3) to 0 V to disable unit (optional remote enable specify suffix ‘-E’ with the model number). Applying a logic ‘0’ will also disable the unit. Options • For the U-channel version, add suffix ‘-U’ to the model number. • For the U-channel version with cover kit, add suffix ‘-C’ to the model number. • For the U-channel version with fan cover kit, add suffix ‘-F’ to the model number. • For screw terminals (output connector P2 only), add suffix ‘-S’ to the model number. • For versions with remote enable, contact sales. • For foldback current limit on single output models, contact sales. • For constant current limit (output 1 & 2) on multi-output models, contact sales. Connector Info For all formats, output connector P2 as follows: Single Output Models: 6-way 0.156" pitch square pin header Molex housing 09-91-0600 Pins 08-50-0106 (24-18 AWG) 08-50-0108 (28-22 AWG) Dual Output Models: 12-way 0.156" pitch square pin header Molex housing 09-91-1200 Pins 08-50-0106 (24-18 AWG) 08-50-0108 (28-22 AWG) Triple Output Models: 14-way 0.156" pitch square pin header Molex housing 09-91-1400 Pins 08-50-0106 (24-18 AWG) 08-50-0108 (28-22 AWG) Quad Output Models: 16-way 0.156" pitch square pin header Molex housing 09-91-1600 Pins 08-50-0106 (24-18 AWG) 08-50-0108 (28-22 AWG) AC-DC RCL175 Models and Ratings All dimensions are in inches (mm) Tolerance ±0.02 (±0.5) Open Frame Weight: 1.10 lbs (500 g) approx. 5.50 (139.7) 0.14 (3.5) MOUNTING HOLE (4 POSITIONS) P2 Pin 6 1.28 (32.4) 3.26 (82.9) P3 Pin 1 2 P1 0.08 (2.0) 3.70 (93.9) Pin 16 Pin 1 0.22 (5.5) Earth/Safety Ground Tag (Class I Operation) 5.23 (132.7) Note: 1. Suitable for class I and class II operation, for class II applications contact sales. 2. Overall height: 1.36 (34.6). U-channel Weight: 1.54 lbs (700 g) approx. 5.71 145.0 0.89 (22.5) 0.47 (12.0) 5.23 (132.7) 3.26 (82.8) 3.90 (99.0) Pin 16 0.14 (3.5) MOUNTING HOLE (4 POSITIONS) P2 P1 3.94 (100.0) 8-32 UNC MOUNTING HOLE (IN 4 POSITIONS) 2.95 (75.0) 0.24 (6.2) 2 M3 MOUNTING HOLE (IN 4 POSITIONS) Pin 1 Earth/Safety Ground Tag 1.18 (30.0) 3.35 (85.0) M3 MOUNTING HOLE (IN 2 POSITIONS EACH SIDE) 0.74 (18.7) 0.55 (14.1) 1.50 (38.1) AC-DC RCL175 Mechanical Details 1.60 (40.8) 2.50 (63.5) 8-32 UNC MOUNTING HOLE (IN 2 POSITIONS, EACH SIDE) Note: 1. Suitable for class I operation only. 2. Mounting screws must not penetrate by more than 0.12” (3.0 mm) max 4.60 (116.8) All dimensions are in inches (mm) U-channel & Cover Weight: 1.76 lbs (800 g) approx. 5.71 (145.0) 0.14 (3.5) MOUNTING HOLE (4 POSITIONS) 3.26 (82.9) 3.90 (99.0) Pin 16 P2 P1 0.89 (22.5) 0.47 (12.0) 5.23 (132.7) 3.94 (100.0) 8-32 UNC MOUNTING HOLE (IN 4 POSITIONS) 2.95 (75.0) 0.24 (6.1) 2 M3 MOUNTING HOLE (IN 4 POSITIONS ) Pin 1 Earth/Safety Ground Tag 4.60 (116.8) 0.55 (14.1) 3.35 (85.0) Note: 1. Suitable for class I operation only. 2. Mounting screws must not penetrate by more than 0.12” (3.0 mm) max 0.74 (1.87) 1.59 (40.4) 1.18 (30.0) M3 MOUNTING HOLE (IN 2 POSITIONS EACH SIDE) 2.50 (63.5) 1.60 (40.8) 8-32 UNC MOUNTING HOLE (IN 2 POSITIONS, EACH SIDE) U-channel & Fan Cover Weight: 1.98 lbs (900 g) approx. 5.71 (145.0) 0.24 (6.1) 0.89 (22.5) 0.47 (12.0) 5.23 (132.7) 3.94 (100.0) 0.14 (3.5) MOUNTING HOLE (4 POSITIONS) P2 P1 8-32 UNC MOUNTING HOLE (IN 4 POSITIONS) 2.95 (75.0) 3.26 (82.9) 3.90 (99.0) Pin 16 M3 MOUNTING HOLE (IN 4 POSITIONS) 2 Pin 1 Earth/Safety Ground Tag 1.18 (30.0) 3.35 (85.0) 0.55 (14.1) 4.60 (116.8) Note: 1. Suitable for class I operation only. 2. Mounting screws must not penetrate by more than 0.12” (3.0 mm) max 0.74 (18.7) 1.57 (40.0) 2.14 (54.4) M3 MOUNTING HOLE (IN 2 POSITIONS, EACH SIDE) 1.60 (40.8) 2.50 (63.5) 8-32 UNC MOUNTING HOLE (IN 2 POSITIONS, EACH SIDE) 03-Jul-08 AC-DC RCL175 Mechanical Details