SPANSION S29GL01GS90THIV010

GL-S MirrorBit® Eclipse™ Flash
Non-Volatile Memory Family
S29GL01GS
S29GL512S
S29GL256S
S29GL128S
1 Gbit
512 Mbit
256 Mbit
128 Mbit
(128 Mbyte)
(64 Mbyte)
(32 Mbyte)
(16 Mbyte)
GL-S MirrorBit® Family Cover Sheet
CMOS 3.0 Volt Core with Versatile I/O
Data Sheet
Notice to Readers: This document states the current technical specifications regarding the Spansion
product(s) described herein. Each product described herein may be designated as Advance Information,
Preliminary, or Full Production. See Notice On Data Sheet Designations for definitions.
Publication Number S29GL_128S_01GS_00
Revision 08
Issue Date October 9, 2013
D at a
S hee t
Notice On Data Sheet Designations
Spansion Inc. issues data sheets with Advance Information or Preliminary designations to advise readers of
product information or intended specifications throughout the product life cycle, including development,
qualification, initial production, and full production. In all cases, however, readers are encouraged to verify
that they have the latest information before finalizing their design. The following descriptions of Spansion data
sheet designations are presented here to highlight their presence and definitions.
Advance Information
The Advance Information designation indicates that Spansion Inc. is developing one or more specific
products, but has not committed any design to production. Information presented in a document with this
designation is likely to change, and in some cases, development on the product may discontinue. Spansion
Inc. therefore places the following conditions upon Advance Information content:
“This document contains information on one or more products under development at Spansion Inc.
The information is intended to help you evaluate this product. Do not design in this product without
contacting the factory. Spansion Inc. reserves the right to change or discontinue work on this proposed
product without notice.”
Preliminary
The Preliminary designation indicates that the product development has progressed such that a commitment
to production has taken place. This designation covers several aspects of the product life cycle, including
product qualification, initial production, and the subsequent phases in the manufacturing process that occur
before full production is achieved. Changes to the technical specifications presented in a Preliminary
document should be expected while keeping these aspects of production under consideration. Spansion
places the following conditions upon Preliminary content:
“This document states the current technical specifications regarding the Spansion product(s)
described herein. The Preliminary status of this document indicates that product qualification has been
completed, and that initial production has begun. Due to the phases of the manufacturing process that
require maintaining efficiency and quality, this document may be revised by subsequent versions or
modifications due to changes in technical specifications.”
Combination
Some data sheets contain a combination of products with different designations (Advance Information,
Preliminary, or Full Production). This type of document distinguishes these products and their designations
wherever necessary, typically on the first page, the ordering information page, and pages with the DC
Characteristics table and the AC Erase and Program table (in the table notes). The disclaimer on the first
page refers the reader to the notice on this page.
Full Production (No Designation on Document)
When a product has been in production for a period of time such that no changes or only nominal changes
are expected, the Preliminary designation is removed from the data sheet. Nominal changes may include
those affecting the number of ordering part numbers available, such as the addition or deletion of a speed
option, temperature range, package type, or VIO range. Changes may also include those needed to clarify a
description or to correct a typographical error or incorrect specification. Spansion Inc. applies the following
conditions to documents in this category:
“This document states the current technical specifications regarding the Spansion product(s)
described herein. Spansion Inc. deems the products to have been in sufficient production volume such
that subsequent versions of this document are not expected to change. However, typographical or
specification corrections, or modifications to the valid combinations offered may occur.”
Questions regarding these document designations may be directed to your local sales office.
2
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
GL-S MirrorBit® Eclipse™ Flash
Non-Volatile Memory Family
S29GL01GS
S29GL512S
S29GL256S
S29GL128S
1 Gbit
512 Mbit
256 Mbit
128 Mbit
(128 Mbyte)
(64 Mbyte)
(32 Mbyte)
(16 Mbyte)
CMOS 3.0 Volt Core with Versatile I/O
Data Sheet
General Description
The Spansion® S29GL01G/512/256/128S are MirrorBit Eclipse flash products fabricated on 65 nm process technology. These
devices offer a fast page access time as fast as 15 ns with a corresponding random access time as fast as 90 ns. They feature
a Write Buffer that allows a maximum of 256 words/512 bytes to be programmed in one operation, resulting in faster effective
programming time than standard programming algorithms. This makes these devices ideal for today’s embedded applications
that require higher density, better performance and lower power consumption.
Distinctive Characteristics
 65 nm MirrorBit Eclipse Technology
 Single supply (VCC) for read / program / erase (2.7V to 3.6V)
 Versatile I/O Feature
– Wide I/O voltage range (VIO): 1.65V to VCC
 Advanced Sector Protection (ASP)
– Volatile and non-volatile protection methods for each sector
 Separate 1024-byte One Time Program (OTP) array with two
lockable regions
 x16 data bus
 Common Flash Interface (CFI) parameter table
 Asynchronous 32-byte Page read
 Temperature Range
– Industrial (-40°C to +85°C)
– In-Cabin (-40°C to +105°C)
 512-byte Programming Buffer
– Programming in Page multiples, up to a maximum of 512 bytes
 Single word and multiple program on same word options
 100,000 erase cycles for any sector typical
 Sector Erase
 20-year data retention typical
– Uniform 128-kbyte sectors
 Suspend and Resume commands for Program and Erase
operations
 Status Register, Data Polling, and Ready/Busy pin methods
to determine device status
Publication Number S29GL_128S_01GS_00
 Packaging Options
–
–
–
–
56-pin TSOP
64-ball LAA Fortified BGA, 13 mm x 11 mm
64-ball LAE Fortified BGA, 9 mm x 9 mm
56-ball VBU Fortified BGA, 9 mm x 7 mm
Revision 08
Issue Date October 9, 2013
This document states the current technical specifications regarding the Spansion product(s) described herein. Spansion Inc. deems the products to have been in sufficient production volume such that subsequent versions of this document are not expected to change. However, typographical or specification corrections, or modifications to the valid combinations offered may occur.
D at a
S hee t
Performance Summary
Maximum Read Access Times
Density
128 Mb
256 Mb
512 Mb
1 Gb
Random Access
Time (tACC)
Voltage Range
Page Access Time
(tPACC)
CE# Access Time
(tCE)
OE# Access Time
(tOE)
Full VCC= VIO
90
15
90
25
VersatileIO VIO
100
25
100
35
Full VCC= VIO
90
15
90
25
VersatileIO VIO
100
25
100
35
Full VCC= VIO
100
15
100
25
VersatileIO VIO
110
25
110
35
Full VCC= VIO
100
15
100
25
VersatileIO VIO
110
25
110
35
Typical Program and Erase Rates
Buffer Programming (512 bytes)
1.5 MB/s
Sector Erase (128 kbytes)
477 kB/s
Maximum Current Consumption
4
Active Read at 5 MHz, 30 pF
60 mA
Program
100 mA
Erase
100 mA
Standby
100 µA
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Table of Contents
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Distinctive Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Performance Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Software Interface
2.
Address Space Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1
Flash Memory Array. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2
Device ID and CFI (ID-CFI) ASO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3
Status Register ASO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4
Data Polling Status ASO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5
Secure Silicon Region ASO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6
Sector Protection Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
13
14
15
16
16
17
3.
Data Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1
Device Protection Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2
Command Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3
Secure Silicon Region (OTP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4
Sector Protection Methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
18
18
18
19
4.
Read Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.1
Asynchronous Read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.2
Page Mode Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.
Embedded Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1
Embedded Algorithm Controller (EAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2
Program and Erase Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3
Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4
Status Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.5
Error Types and Clearing Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.6
Embedded Algorithm Performance Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.
Software Interface Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
6.1
Command Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
6.2
Device ID and Common Flash Interface (ID-CFI) ASO Map . . . . . . . . . . . . . . . . . . . . . . . . . 60
25
25
26
27
37
42
46
Hardware Interface
7.
Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1
Address and Data Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2
Input/Output Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3
Versatile I/O Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.4
Ready/Busy# (RY/BY#) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.5
Hardware Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
65
65
65
65
66
66
8.
Signal Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1
Interface States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2
Power-Off with Hardware Data Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.3
Power Conservation Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.4
Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.5
Write. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
67
67
67
68
68
69
9.
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.1
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.2
Latchup Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.3
Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.4
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.5
Capacitance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
71
71
71
71
74
76
10.
Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
10.1 Key to Switching Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
10.2 AC Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
5
D at a
10.3
10.4
6
S hee t
Power-On Reset (POR) and Warm Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
11.
Physical Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.1 56-Pin TSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.2 64-Ball FBGA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.3 56-Ball FBGA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.
Special Handling Instructions for FBGA Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
13.
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
14.
Other Resources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.1 Links to Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.2 Links to Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.3 Specification Bulletins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.4 Contacting Spansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
GL-S MirrorBit® Family
91
91
93
96
101
101
101
102
102
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Figures
Figure 1.1
Figure 3.1
Figure 5.1
Figure 5.2
Figure 5.3
Figure 5.4
Figure 5.5
Figure 5.6
Figure 9.1
Figure 9.2
Figure 9.3
Figure 9.4
Figure 10.1
Figure 10.2
Figure 10.3
Figure 10.4
Figure 10.5
Figure 10.6
Figure 10.7
Figure 10.8
Figure 10.9
Figure 10.10
Figure 10.11
Figure 10.12
Figure 10.13
Figure 10.14
Figure 10.15
Figure 10.16
Figure 10.17
Figure 10.18
Figure 10.19
Figure 10.20
Figure 11.1
Figure 11.2
Figure 11.3
Figure 11.4
Figure 11.5
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Advanced Sector Protection Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Word Program Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Write Buffer Programming Operation with Data Polling Status . . . . . . . . . . . . . . . . . . . . . . .
Write Buffer Programming Operation with Status Register . . . . . . . . . . . . . . . . . . . . . . . . . .
Sector Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data# Polling Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Toggle Bit Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-down and Voltage Drop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Negative Overshoot Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Positive Overshoot Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Waveforms and Measurement Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Up Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back to Back Read (tACC) Operation Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back to Back Read Operation (tRC)Timing Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page Read Timing Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back to Back Write Operation Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back to Back (CE#VIL) Write Operation Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . .
Write to Read (tACC) Operation Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Write to Read (tCE) Operation Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Read to Write (CE# VIL) Operation Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Read to Write (CE# Toggle) Operation Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Program Operation Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chip/Sector Erase Operation Timing Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data# Polling Timing Diagram (During Embedded Algorithms) . . . . . . . . . . . . . . . . . . . . . . .
Toggle Bit Timing Diagram (During Embedded Algorithms) . . . . . . . . . . . . . . . . . . . . . . . . .
DQ2 vs. DQ6 Relationship Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back to Back (CE#) Write Operation Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(CE#) Write to Read Operation Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
56-Pin Standard TSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
56-Pin Thin Small Outline Package (TSOP), 14 x 20 mm . . . . . . . . . . . . . . . . . . . . . . . . . . .
64-ball Fortified Ball Grid Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LAE064—64-ball Fortified Ball Grid Array (FBGA), 9 x 9 mm . . . . . . . . . . . . . . . . . . . . . . . .
56-ball Fortified Ball Grid Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
10
19
27
29
30
33
39
41
72
72
73
73
77
77
78
79
82
82
82
83
84
84
85
85
86
87
87
88
88
88
89
90
91
92
93
94
96
7
D at a
S hee t
Tables
Table 1.1
Table 2.1
Table 2.2
Table 2.3
Table 2.4
Table 2.5
Table 2.6
Table 3.1
Table 3.2
Table 5.1
Table 5.2
Table 5.3
Table 5.4
Table 5.5
Table 5.6
Table 5.7
Table 5.8
Table 5.9
Table 5.10
Table 5.11
Table 5.12
Table 5.13
Table 5.14
Table 5.15
Table 5.16
Table 5.17
Table 5.18
Table 5.19
Table 5.20
Table 5.21
Table 5.22
Table 5.23
Table 5.24
Table 5.25
Table 5.26
Table 6.1
Table 6.2
Table 6.3
Table 6.4
Table 6.5
Table 6.6
Table 7.1
Table 8.1
Table 9.1
Table 9.2
Table 9.3
Table 9.4
Table 9.5
Table 9.6
Table 9.7
Table 10.1
Table 10.2
Table 10.3
Table 10.4
Table 10.5
Table 10.6
8
S29GL-S Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S29GL01GS Sector and Memory Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S29GL512S Sector and Memory Address Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S29GL256S Sector and Memory Address Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S29GL128S Sector and Memory Address Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ID-CFI Address Map Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Secure Silicon Region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sector Protection States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lock Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Write Buffer Programming Command Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Polling Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Embedded Algorithm Characteristics (-40°C to +85°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Embedded Algorithm Characteristics (-40°C to +105°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Read Command State Transition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Read Unlock Command State Transition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Erase State Command Transition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Erase Suspend State Command Transition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Erase Suspend Unlock State Command Transition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Erase Suspend - DYB State Command Transition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Erase Suspend - Program Command State Transition . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Erase Suspend - Program Suspend Command State Transistion. . . . . . . . . . . . . . . . . . . . .
Program State Command Transition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Program Unlock State Command Transition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Program Suspend State Command Transition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lock Register State Command Transition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CFI State Command Transition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Secure Silicon Sector State Command Transition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Secure Silicon Sector Unlock State Command Transition. . . . . . . . . . . . . . . . . . . . . . . . . . .
Secure Silicon Sector Program State Command Transition . . . . . . . . . . . . . . . . . . . . . . . . .
Password Protection Command State Transition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Non-Volatile Protection Command State Transition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PPB Lock Bit Command State Transition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Volatile Sector Protection Command State Transition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
State Transition Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Command Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ID (Autoselect) Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CFI Query Identification String. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CFI System Interface String. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CFI Device Geometry Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CFI Primary Vendor-Specific Extended Query . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/O Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interface States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Up/Power-Down Voltage and Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DC Characteristics (-40°C to +85°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DC Characteristics (-40°C to +105°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connector Capacitance for FBGA (LAA) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connector Capacitance for FBGA (LAE) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connector Capacitance for TSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power ON and Reset Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Read Operation VIO = VCC = 2.7V to 3.6V (-40°C to +85°C) . . . . . . . . . . . . . . . . . . . . . . . . .
Read Operation VIO = 1.65V to VCC, VCC = 2.7V to 3.6V (-40°C to +85°C) . . . . . . . . . . . . .
Read Operation VIO = VCC = 2.7V to 3.6V (-40°C to +105°C) . . . . . . . . . . . . . . . . . . . . . . . .
Read Operation VIO = 1.65V to VCC, VCC = 2.7V to 3.6V (-40°C to +105°C) . . . . . . . . . . . .
GL-S MirrorBit® Family
11
13
13
13
14
14
16
21
21
31
38
42
46
47
48
48
48
49
49
49
50
50
51
51
51
52
52
52
52
53
53
54
54
54
55
57
60
61
61
62
63
65
67
71
72
74
75
76
76
76
77
78
80
80
81
81
S29GL_128S_01GS_00_08 October 9, 2013
Data
Table 10.7
Table 10.8
Table 10.9
Table 13.1
She et
Write Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Erase/Program Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alternate CE# Controlled Write Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S29GL-S Valid Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
83
86
89
98
9
D at a
1.
S hee t
Product Overview
The GL-S family consists of 128-Mbit to 1Gbit, 3.0V core, Versatile I/O, non-volatile, flash memory devices.
These devices have a 16-bit (word) wide data bus and use only word boundary addresses. All read accesses
provide 16 bits of data on each bus transfer cycle. All writes take 16 bits of data from each bus transfer cycle.
Figure 1.1 Block Diagram
DQ15–DQ0
RY/BY#
VCC
Sector Switches
VSS
VIO
Erase Voltage
Generator
Input/Output
Buffers
RESET#
WE#
WP#
State
Control
Command
Register
PGM Voltage
Generator
Chip Enable
Output Enable
Logic
CE#
OE#
AMax**–A0
Address Latch
Timer
Data
Latch
Y-Decoder
Y-Gating
X-Decoder
Cell Matrix
STB
VCC Detector
STB
:
Note:
** AMAX GL01GS = A25, AMAX GL512S = A24, AMAX GL256S = A23, AMAX GL128S = A22
The GL-S family combines the best features of eXecute In Place (XIP) and Data Storage flash memories.
This family has the fast random access of XIP flash along with the high density and fast program speed of
Data Storage flash.
Read access to any random location takes 90 ns to 120 ns depending on device density and I/O power
supply voltage. Each random (initial) access reads an entire 32-byte aligned group of data called a Page.
Other words within the same Page may be read by changing only the low order 4 bits of word address. Each
access within the same Page takes 15 ns to 30 ns. This is called Page Mode read. Changing any of the
higher word address bits will select a different Page and begin a new initial access. All read accesses are
asynchronous.
10
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Table 1.1 S29GL-S Address Map
Type
Count
Addresses
Address within Page
16
A3 - A0
Address within Write Buffer
256
A7 - A0
Page
4096
A15 - A4
Write-Buffer-Line
256
A15 - A8
1024 (1 Gb)
512 (512 Mb)
Sector
256 (256 Mb)
AMAX - A16
128 (128 Mb)
The device control logic is subdivided into two parallel operating sections, the Host Interface Controller (HIC)
and the Embedded Algorithm Controller (EAC). HIC monitors signal levels on the device inputs and drives
outputs as needed to complete read and write data transfers with the host system. HIC delivers data from the
currently entered address map on read transfers; places write transfer address and data information into the
EAC command memory; notifies the EAC of power transition, hardware reset, and write transfers. The EAC
looks in the command memory, after a write transfer, for legal command sequences and performs the related
Embedded Algorithms.
Changing the non-volatile data in the memory array requires a complex sequence of operations that are
called Embedded Algorithms (EA). The algorithms are managed entirely by the device internal EAC. The
main algorithms perform programming and erase of the main array data. The host system writes command
codes to the flash device address space. The EAC receives the commands, performs all the necessary steps
to complete the command, and provides status information during the progress of an EA.
The erased state of each memory bit is a logic 1. Programming changes a logic 1 (High) to a logic 0 (Low).
Only an Erase operation is able to change a 0 to a 1. An erase operation must be performed on an entire
128-kbyte aligned and length group of data call a Sector. When shipped from Spansion all Sectors are
erased.
Programming is done via a 512-byte Write Buffer. It is possible to write from 1 to 256 words, anywhere within
the Write Buffer before starting a programming operation. Within the flash memory array, each 512-byte
aligned group of 512 bytes is called a Line. A programming operation transfers volatile data from the Write
Buffer to a non-volatile memory array Line. The operation is called Write Buffer Programming.
The Write Buffer is filled with 1’s after reset or the completion of any operation using the Write Buffer. Any
locations not written to a 0 by a Write to Buffer command are by default still filled with 1’s. Any 1’s in the Write
Buffer do not affect data in the memory array during a programming operation.
As each Page of data that was loaded into the Write Buffer is transferred to a memory array Line.
Sectors may be individually protected from program and erase operations by the Advanced Sector Protection
(ASP) feature set. ASP provides several, hardware and software controlled, volatile and non-volatile,
methods to select which sectors are protected from program and erase operations.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
11
D at a
S hee t
Software Interface
2. Address Space Maps
There are several separate address spaces that may appear within the address range of the flash memory
device. One address space is visible (entered) at any given time.
 Flash Memory Array: the main non-volatile memory array used for storage of data that may be randomly
accessed by asynchronous read operations.
 ID/CFI: a memory array used for Spansion factory programmed device characteristics information. This
area contains the Device Identification (ID) and Common Flash Interface (CFI) information tables.
 Secure Silicon Region (SSR): a One Time Programmable (OTP) non-volatile memory array used for
Spansion factory programmed permanent data, and customer programmable permanent data.
 Lock Register: an OTP non-volatile word used to configure the ASP features and lock the SSR.
 Persistent Protection Bits (PPB): a non-volatile flash memory array with one bit for each Sector. When
programmed, each bit protects the related Sector from erasure and programming.
 PPB Lock: a volatile register bit used to enable or disable programming and erasure of the PPB bits.
 Password: an OTP non-volatile array used to store a 64-bit password used to enable changing the state of
the PPB Lock Bit when using Password Mode sector protection.
 Dynamic Protection Bits (DYB): a volatile array with one bit for each Sector. When set, each bit protects the
related Sector from erasure and programming.
 Status Register: a volatile register used to display Embedded Algorithm status.
 Data Polling Status: a volatile register used as an alternate, legacy software compatible, way to display
Embedded Algorithm status.
The main Flash Memory Array is the primary and default address space but, it may be overlaid by one other
address space, at any one time. Each alternate address space is called an Address Space Overlay (ASO).
Each ASO replaces (overlays) the entire flash device address range. Any address range not defined by a
particular ASO address map, is reserved for future use. All read accesses outside of an ASO address map
returns non-valid (undefined) data. The locations will display actively driven data but the meaning of whatever
1’s or 0’s appear are not defined.
There are four device operating modes that determine what appears in the flash device address space at any
given time:
 Read Mode
 Data Polling Mode
 Status Register (SR) Mode
 Address Space Overlay (ASO) Mode
In Read Mode the entire Flash Memory Array may be directly read by the host system memory controller. The
memory device Embedded Algorithm Controller (EAC), puts the device in Read mode during Power-on, after
a Hardware Reset, after a Command Reset, or after an Embedded Algorithm (EA) is suspended. Read
accesses and command writes are accepted in read mode. A subset of commands are accepted in read
mode when an EA is suspended.
While in any mode, the Status Register read command may be issued to cause the Status Register ASO to
appear at every word address in the device address space. In this Status Register ASO Mode, the device
interface waits for a read access and, any write access is ignored. The next read access to the device
accesses the content of the status register, exits the Status Register ASO, and returns to the previous
(calling) mode in which the Status Register read command was received.
In EA mode the EAC is performing an Embedded Algorithm, such as programming or erasing a non-volatile
memory array. While in EA mode, none of the main Flash Memory Array is readable because the entire flash
device address space is replaced by the Data Polling Status ASO. Data Polling Status will appear at every
word location in the device address space.
12
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
While in EA mode, only a Program / Erase suspend command or the Status Register Read command will be
accepted. All other commands are ignored. Thus, no other ASO may be entered from the EA mode.
When an Embedded Algorithm is suspended, the Data Polling ASO is visible until the device has suspended
the EA. When the EA is suspended the Data Polling ASO is exited and Flash Array data is available. The
Data Polling ASO is reentered when the suspended EA is resumed, until the EA is again suspended or
finished. When an Embedded Algorithm is completed, the Data Polling ASO is exited and the device goes to
the previous (calling) mode (from which the Embedded Algorithm was started).
In ASO mode, one of the remaining overlay address spaces is entered (overlaid on the main Flash Array
address map). Only one ASO may be entered at any one time. Commands to the device affect the currently
entered ASO. Only certain commands are valid for each ASO. These are listed in the Table 6.1 on page 57,
in each ASO related section of the table.
The following ASOs have non-volatile data that may be programmed to change 1’s to 0’s:
 Secure Silicon Region
 Lock Register
 Persistent Protection Bits (PPB)
 Password
 Only the PPB ASO has non-volatile data that may be erased to change 0’s to 1’s
When a program or erase command is issued while one of the non-volatile ASOs is entered, the EA operates
on the ASO. The ASO is not readable while the EA is active. When the EA is completed the ASO remains
entered and is again readable. Suspend and Resume commands are ignored during an EA operating on any
of these ASOs.
2.1
Flash Memory Array
The S29GL-S family has uniform sector architecture with a sector size of 128 kB. Table 2.1 to Table 2.4
shows the sector architecture of the four devices.
Table 2.1 S29GL01GS Sector and Memory Address Map
Sector Size (kbyte)
Sector Count
128
1024
Sector Range
Address Range
(16-Bit)
Notes
SA00
0000000h-000FFFFh
Sector Starting Address
:
:
–
SA1023
3FF0000h-3FFFFFFh
Sector Ending Address
Table 2.2 S29GL512S Sector and Memory Address Map
Sector Size (kbyte)
Sector Count
128
512
Sector Range
Address Range
(16-Bit)
Notes
SA00
0000000h-000FFFFh
Sector Starting Address
:
:
–
SA511
1FF0000h-1FFFFFFh
Sector Ending Address
Table 2.3 S29GL256S Sector and Memory Address Map
Sector Size (kbyte)
Sector Count
128
256
October 9, 2013 S29GL_128S_01GS_00_08
Sector Range
Address Range
(16-Bit)
Notes
SA00
0000000h-000FFFFh
Sector Starting Address
:
:
–
SA255
0FF0000h-0FFFFFFh
Sector Ending Address
GL-S MirrorBit® Family
13
D at a
S hee t
Table 2.4 S29GL128S Sector and Memory Address Map
Sector Size (kbyte)
128
Sector Count
128
Sector Range
Address Range
(16-Bit)
Notes
SA00
0000000h-000FFFFh
Sector Starting Address
:
:
–
SA127
07F0000h-07FFFFFh
Sector Ending Address
Note: These tables have been condensed to show sector related information for an entire device on a single
page Sectors and their address ranges that are not explicitly listed (such as SA001-SA510) have sectors
starting and ending addresses that form the same pattern as all other sectors of that size. For example, all
128 kB sectors have the pattern XXX0000h-XXXFFFFh.
2.2
Device ID and CFI (ID-CFI) ASO
There are two traditional methods for systems to identify the type of flash memory installed in the system.
One has traditionally been called Autoselect and is now referred to as Device Identification (ID). The other
method is called Common Flash Interface (CFI).
For ID, a command is used to enable an address space overlay where up to 16 word locations can be read to
get JEDEC manufacturer identification (ID), device ID, and some configuration and protection status
information from the flash memory. The system can use the manufacturer and device IDs to select the
appropriate driver software to use with the flash device.
CFI also uses a command to enable an address space overlay where an extendable table of standard
information about how the flash memory is organized and operates can be read. With this method the driver
software does not have to be written with the specifics of each possible memory device in mind. Instead the
driver software is written in a more general way to handle many different devices but adjusts the driver
behavior based on the information in the CFI table.
Traditionally these two address spaces have used separate commands and were separate overlays.
However, the mapping of these two address spaces are non-overlapping and so can be combined in to a
single address space and appear together in a single overlay. Either of the traditional commands used to
access (enter) the Autoselect (ID) or CFI overlay will cause the now combined ID-CFI address map to appear.
The ID-CFI address map appears within, and overlays the Flash Array data of, the sector selected by the
address used in the ID-CFI enter command. While the ID-CFI ASO is entered the content of all other sectors
is undefined.
The ID-CFI address map starts at location 0 of the selected sector. Locations above the maximum defined
address of the ID-CFI ASO to the maximum address of the selected sector have undefined data. The ID-CFI
enter commands use the same address and data values used on previous generation memories to access
the JEDEC Manufacturer ID (Autoselect) and Common Flash Interface (CFI) information, respectively.
Table 2.5 ID-CFI Address Map Overview
Word Address
Description
Read / Write
(SA) + 0000h to 000Fh
Device ID
(traditional Autoselect values)
Read Only
(SA) + 0010h to 0079h
CFI data structure
Read Only
(SA) + 0080h to FFFFh
Undefined
Read Only
For the complete address map see Table 6.2 on page 60.
14
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
2.2.1
She et
Device ID
The Joint Electron Device Engineering Council (JEDEC) standard JEP106T defines the manufacturer ID for a
compliant memory. Common industry usage defined a method and format for reading the manufacturer ID
and a device specific ID from a memory device. The manufacturer and device ID information is primarily
intended for programming equipment to automatically match a device with the corresponding programming
algorithm. Spansion has added additional fields within this 32-byte address space.
The original industry format was structured to work with any memory data bus width e. g. x8, x16, x32. The ID
code values are traditionally byte wide but are located at bus width address boundaries such that
incrementing the device address inputs will read successive byte, word, or double word locations with the ID
codes always located in the least significant byte location of the data bus. Because the device data bus is
word wide each code byte is located in the lower half of each word location. The original industry format made
the high order byte always 0. Spansion has modified the format to use both bytes in some words of the
address space. For the detail description of the Device ID address map see Table 6.2 on page 60.
2.2.2
Common Flash Memory Interface
The JEDEC Common Flash Interface (CFI) specification (JESD68.01) defines a standardized data structure
that may be read from a flash memory device, which allows vendor-specified software algorithms to be used
for entire families of devices. The data structure contains information for system configuration such as various
electrical and timing parameters, and special functions supported by the device. Software support can then
be device-independent, Device ID-independent, and forward-and-backward-compatible for entire Flash
device families.
The system can read CFI information at the addresses within the selected sector as shown in Device ID and
Common Flash Interface (ID-CFI) ASO Map on page 60.
Like the Device ID information, CFI information is structured to work with any memory data bus width e. g. x8,
x16, x32. The code values are always byte wide but are located at data bus width address boundaries such
that incrementing the device address reads successive byte, word, or double word locations with the codes
always located in the least significant byte location of the data bus. Because the data bus is word wide each
code byte is located in the lower half of each word location and the high order byte is always 0.
For further information, please refer to the Spansion CFI Specification, Version 1.4 (or later), and the JEDEC
publications JEP137-A and JESD68.01. Please contact JEDEC (http://www.jedec.org/) for their standards
and the Spansion CFI Specification may be found at the Spansion Web site
(http://www.spansion.com/Support/TechnicalDocuments/Pages/ApplicationNotes.aspx at the time of this
document's publication) or by contacting a local Spansion sales office listed on the web site.
2.3
Status Register ASO
The Status Register ASO contains a single word of registered volatile status for Embedded Algorithms. When
the Status Register read command is issued, the current status is captured (by the rising edge of WE#) into
the register and the ASO is entered. The Status Register content appears on all word locations. The first read
access exits the Status Register ASO (with the rising edge of CE# or OE#) and returns to the address space
map in use when the Status Register read command was issued. Write commands will not exit the Status
Register ASO state.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
15
D at a
2.4
S hee t
Data Polling Status ASO
The Data Polling Status ASO contains a single word of volatile memory indicating the progress of an EA. The
Data Polling Status ASO is entered immediately following the last write cycle of any command sequence that
initiates an EA. Commands that initiate an EA are:
 Word Program
 Program Buffer to Flash
 Chip Erase
 Sector Erase
 Erase Resume / Program Resume
 Program Resume Enhanced Method
 Blank Check
 Lock Register Program
 Password Program
 PPB Program
 All PPB Erase
The Data Polling Status word appears at all word locations in the device address space. When an EA is
completed the Data Polling Status ASO is exited and the device address space returns to the address map
mode where the EA was started.
2.5
Secure Silicon Region ASO
The Secure Silicon Region (SSR) provides an extra flash memory area that can be programmed once and
permanently protected from further changes i. e. it is a One Time Program (OTP) area. The SSR is
1024 bytes in length. It consists of 512 bytes for Factory Locked Secure Silicon Region and 512 bytes for
Customer Locked Secure Silicon Region.
The sector address supplied during the Secure Silicon Entry command selects the Flash Memory Array
sector that is overlaid by the Secure Silicon Region address map. The SSR is overlaid starting at location 0 in
the selected sector. Use of the sector 0 address is recommended for future compatibility. While the SSR ASO
is entered the content of all other sectors is undefined. Locations above the maximum defined address of the
SSR ASO to the maximum address of the selected sector have undefined data.
Table 2.6 Secure Silicon Region
16
Word Address Range
Content
Size
(SA) + 0000h to 00FFh
Factory Locked Secure Silicon Region
512 bytes
(SA) + 0100h to 01FFh
Customer Locked Secure Silicon Region
512 bytes
(SA) + 0200h to FFFFh
Undefined
127 kbytes
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
2.6
2.6.1
She et
Sector Protection Control
Lock Register ASO
The Lock register ASO contains a single word of OTP memory. When the ASO is entered the Lock Register
appears at all word locations in the device address space. However, it is recommended to read or program
the Lock Register only at location 0 of the device address space for future compatibility.
2.6.2
Persistent Protection Bits (PPB) ASO
The PPB ASO contains one bit of a Flash Memory Array for each Sector in the device. When the PPB ASO is
entered, the PPB bit for a sector appears in the Least Significant Bit (LSB) of each address in the sector.
Reading any address in a sector displays data where the LSB indicates the non-volatile protection status for
that sector. However, it is recommended to read or program the PPB only at address 0 of the sector for future
compatibility. If the bit is 0 the sector is protected against programming and erase operations. If the bit is 1 the
sector is not protected by the PPB. The sector may be protected by other features of ASP.
2.6.3
PPB LOCK ASO
The PPB Lock ASO contains a single bit of volatile memory. The bit controls whether the bits in the PPB ASO
may be programmed or erased. If the bit is 0 the PPB ASO is protected against programming and erase
operations. If the bit is 1 the PPB ASO is not protected. When the PPB Lock ASO is entered the PPB Lock bit
appears in the Least Significant Bit (LSB) of each address in the device address space. However, it is
recommended to read or program the PPB Lock only at address 0 of the device for future compatibility.
2.6.4
Password ASO
The Password ASO contains four words of OTP memory. When the ASO is entered the Password appears
starting at address 0 in the device address space. All locations above the forth word are undefined.
2.6.5
Dynamic Protection Bits (DYB) ASO
The DYB ASO contains one bit of a volatile memory array for each Sector in the device. When the DYB ASO
is entered, the DYB bit for a sector appears in the Least Significant Bit (LSB) of each address in the sector.
Reading any address in a sector displays data where the LSB indicates the non-volatile protection status for
that sector. However, it is recommended to read, set, or clear the DYB only at address 0 of the sector for
future compatibility. If the bit is 0 the sector is protected against programming and erase operations. If the bit
is 1 the sector is not protected by the DYB. The sector may be protected by other features of ASP.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
17
D at a
3.
S hee t
Data Protection
The device offers several features to prevent malicious or accidental modification of any sector via hardware
means.
3.1
3.1.1
Device Protection Methods
Power-Up Write Inhibit
RESET#, CE#, WE#, and, OE# are ignored during Power-On Reset (POR). During POR, the device can not
be selected, will not accept commands on the rising edge of WE#, and does not drive outputs. The Host
Interface Controller (HIC) and Embedded Algorithm Controller (EAC) are reset to their standby states, ready
for reading array data, during POR. CE# or OE# must go to VIH before the end of POR (tVCS).
At the end of POR the device conditions are:
 all internal configuration information is loaded,
 the device is in read mode,
 the Status Register is at default value,
 all bits in the DYB ASO are set to un-protect all sectors,
 the Write Buffer is loaded with all 1’s,
 the EAC is in the standby state.
3.1.2
Low VCC Write Inhibit
When VCC is less than VLKO, the HIC does not accept any write cycles and the EAC resets. This protects data
during VCC power-up and power-down. The system must provide the proper signals to the control pins to
prevent unintentional writes when VCC is greater than VLKO.
3.2
Command Protection
Embedded Algorithms are initiated by writing command sequences into the EAC command memory. The
command memory array is not readable by the host system and has no ASO. Each host interface write is a
command or part of a command sequence to the device. The EAC examines the address and data in each
write transfer to determine if the write is part of a legal command sequence. When a legal command
sequence is complete the EAC will initiate the appropriate EA.
Writing incorrect address or data values, or writing them in an improper sequence, will generally result in the
EAC returning to its Standby state. However, such an improper command sequence may place the device in
an unknown state, in which case the system must write the reset command, or possibly provide a hardware
reset by driving the RESET# signal Low, to return the EAC to its Standby state, ready for random read.
The address provided in each write may contain a bit pattern used to help identify the write as a command to
the device. The upper portion of the address may also select the sector address on which the command
operation is to be performed. The Sector Address (SA) includes AMAX through A16 flash address bits (system
byte address signals amax through a17). A command bit pattern is located in A10 to A0 flash address bits
(system byte address signals a11 through a1).
The data in each write may be: a bit pattern used to help identify the write as a command, a code that
identifies the command operation to be performed, or supply information needed to perform the operation.
See Table 6.1 on page 57 for a listing of all commands accepted by the device.
3.3
Secure Silicon Region (OTP)
The Secure Silicon Region (SSR) provides an extra flash memory area that can be programmed once and
permanently protected from further changes i. e. it is a One Time Program (OTP) area. The SSR is
1024 bytes in length. It consists of 512 bytes for Factory Locked Secure Silicon Region and 512 bytes for
Customer Locked Secure Silicon Region.
18
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
3.4
3.4.1
She et
Sector Protection Methods
Write Protect Signal
If WP# = VIL, the lowest or highest address sector is protected from program or erase operations independent
of any other ASP configuration. Whether it is the lowest or highest sector depends on the device ordering
option (model) selected. If WP# = VIH, the lowest or highest address sector is not protected by the WP# signal
but it may be protected by other aspects of ASP configuration. WP# has an internal pull-up; when
unconnected, WP# is at VIH.
3.4.2
ASP
Advanced Sector Protection (ASP) is a set of independent hardware and software methods used to disable or
enable programming or erase operations, individually, in any or all sectors. This section describes the various
methods of protecting data stored in the memory array. An overview of these methods is shown in Figure 3.1.
Figure 3.1 Advanced Sector Protection Overview
Lock Register
(One Time Programmable)
Password Method
Persistent Method
(DQ2)
(DQ1)
64-bit Password
(One Time Protect)
1,2,3
PPB Lock Bit
0 = PPBs Locked
1 = PPBs Unlocked
1. Bit is volatile, and defaults to “1” on reset (to
“0” if in Password Mode).
2. Programming to “0” locks all PPBs to their
current state.
3. Once programmed to “0”, requires hardware
reset to unlock or application of the
password.
Memory Array
Persistent
Protection Bit
(PPB)5,6
Sector 0
PPB 0
DYB 0
Sector 1
PPB 1
DYB 1
Sector 2
PPB 2
DYB 2
Sector N-2
PPB N-2
DYB N-2
Sector N-1
PPB N-1
DYB N-1
PPB N
DYB N
Sector N
4
4. N = Highest Address Sector.
5. 0 = Sector Protected,
1 = Sector Unprotected.
6. PPBs programmed individually,
but cleared collectively
Dynamic
Protection Bit
(DYB)7,8,9
7. 0 = Sector Protected,
1 = Sector Unprotected.
8. Protect effective only if corresponding PPB
is “1” (unprotected).
9. Volatile Bits: defaults to user choice upon
power-up (see ordering options).
Every main flash array sector has a non-volatile (PPB) and a volatile (DYB) protection bit associated with it.
When either bit is 0, the sector is protected from program and erase operations.
The PPB bits are protected from program and erase when the PPB Lock bit is 0. There are two methods for
managing the state of the PPB Lock bit, Persistent Protection and Password Protection.
The Persistent Protection method sets the PPB Lock to 1 during POR or Hardware Reset so that the PPB bits
are unprotected by a device reset. There is a command to clear the PPB Lock bit to 0 to protect the PPB bits.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
19
D at a
S hee t
There is no command in the Persistent Protection method to set the PPB Lock bit therefore the PPB Lock bit
will remain at 0 until the next power-off or hardware reset. The Persistent Protection method allows boot code
the option of changing sector protection by programming or erasing the PPB, then protecting the PPB from
further change for the remainder of normal system operation by clearing the PPB Lock bit. This is sometimes
called Boot-code controlled sector protection.
The Password method clears the PPB Lock bit to 0 during POR or Hardware Reset to protect the PPB. A 64bit password may be permanently programmed and hidden for the password method. A command can be
used to provide a password for comparison with the hidden password. If the password matches the PPB Lock
bit is set to 1 to unprotect the PPB. A command can be used to clear the PPB Lock bit to 0.
The selection of the PPB Lock management method is made by programming OTP bits in the Lock Register
so as to permanently select the method used.
The Lock Register also contains OTP bits, for protecting the SSR.
The PPB bits are erased so that all main flash array sectors are unprotected when shipped from Spansion.
The Secured Silicon Region can be factory protected or left unprotected depending on the ordering option
(model) ordered.
3.4.3
PPB Lock
The Persistent Protection Bit Lock is a volatile bit for protecting all PPB bits. When cleared to 0, it locks all
PPBs and when set to 1, it allows the PPBs to be changed. There is only one PPB Lock Bit per device.
The PPB Lock command is used to clear the bit to 0. The PPB Lock Bit must be cleared to 0 only after all the
PPBs are configured to the desired settings.
In Persistent Protection mode, the PPB Lock is set to 1 during POR or a hardware reset. When cleared, no
software command sequence can set the PPB Lock, only another hardware reset or power-up can set the
PPB Lock bit.
In the Password Protection mode, the PPB Lock is cleared to 0 during POR or a hardware reset. The PPB
Lock can only set to 1 by the Password Unlock command sequence. The PPB Lock can be cleared by the
PPB Lock Bit Clear command.
3.4.4
Persistent Protection Bits (PPB)
The Persistent Protection Bits (PPB) are located in a separate nonvolatile flash array. One of the PPB bits is
assigned to each sector. When a PPB is 0 its related sector is protected from program and erase operations.
The PPB are programmed individually but must be erased as a group, similar to the way individual words may
be programmed in the main array but an entire sector must be erased at the same time. Preprogramming and
verification prior to erasure are handled by the EAC.
Programming a PPB bit requires the typical word programming time. During a PPB bit programming operation
or PPB bit erasing, Data polling Status DQ6 Toggle Bit I will toggle until the operation is complete. Erasing all
the PPBs requires typical sector erase time.
If the PPB Lock is 0, the PPB Program or erase commands do not execute and time-out without programming
or erasing the PPB.
The protection state of a PPB for a given sector can be verified by executing a PPB Status Read command
when entered in the PPB ASO.
3.4.5
Dynamic Protection Bits (DYB)
Dynamic Protection Bits are volatile and unique for each sector and can be individually modified. DYBs only
control protection for sectors that have their PPBs erased. By issuing the DYB Set or Clear command
sequences, the DYB are set to 0 or cleared to 1, thus placing each sector in the protected or unprotected
state respectively, if the PPB for the Sector is 1. This feature allows software to easily protect sectors against
inadvertent changes, yet does not prevent the easy removal of protection when changes are needed.
The DYB can be set to 0 or cleared to 1 as often as needed.
20
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
3.4.6
She et
Sector Protection States Summary
Each sector can be in one of the following protection states:
 Unlocked – The sector is unprotected and protection can be changed by a simple command. The
protection state defaults to unprotected after a power cycle or hardware reset.
 Dynamically Locked – A sector is protected and protection can be changed by a simple command. The
protection state is not saved across a power cycle or hardware reset.
 Persistently Locked – A sector is protected and protection can only be changed if the PPB Lock Bit is set to
1. The protection state is non-volatile and saved across a power cycle or hardware reset. Changing the
protection state requires programming or erase of the PPB bits.
Table 3.1 Sector Protection States
Protection Bit Values
Sector State
PPB Lock
3.4.7
PPB
DYB
1
1
1
Unprotected - PPB and DYB are changeable
1
1
0
Protected - PPB and DYB are changeable
1
0
1
Protected - PPB and DYB are changeable
1
0
0
Protected - PPB and DYB are changeable
0
1
1
Unprotected - PPB not changeable, DYB is changeable
0
1
0
Protected - PPB not changeable, DYB is changeable
0
0
1
Protected - PPB not changeable, DYB is changeable
0
0
0
Protected - PPB not changeable, DYB is changeable
Lock Register
The Lock Register holds the non-volatile OTP bits for controlling protection of the SSR, and determining the
PPB Lock bit management method (protection mode).
Table 3.2 Lock Register
Bit
Default Value
15-9
1
Reserved
Name
8
0
Reserved
7
X
Reserved
6
1
SSR Region 1 (Customer) Lock Bit
5
1
Reserved
4
1
Reserved
3
1
Reserved
2
1
Password Protection Mode Lock Bit
1
1
Persistent Protection Mode Lock Bit
0
0
SSR Region 0 (Factory) Lock Bit
The Secure Silicon Region (SSR) protection bits must be used with caution, as once locked, there is no
procedure available for unlocking the protected portion of the Secure Silicon Region and none of the bits in
the protected Secure Silicon Region memory space can be modified in any way. Once the Secure Silicon
Region area is protected, any further attempts to program in the area will fail with status indicating the area
being programmed is protected. The Region 0 Indicator Bit is located in the Lock Register at bit location 0 and
Region 1 in bit location 6.
As shipped from the factory, all devices default to the Persistent Protection method, with all sectors
unprotected, when power is applied. The device programmer or host system can then choose which sector
protection method to use. Programming either of the following two, one-time programmable, non-volatile bits,
locks the part permanently in that mode:
 Persistent Protection Mode Lock Bit (DQ1)
 Password Protection Mode Lock Bit (DQ2)
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
21
D at a
S hee t
If both lock bits are selected to be programmed at the same time, the operation will abort. Once the Password
Mode Lock Bit is programmed, the Persistent Mode Lock Bit is permanently disabled and no changes to the
protection scheme are allowed. Similarly, if the Persistent Mode Lock Bit is programmed, the Password Mode
is permanently disabled.
If the password mode is to be chosen, the password must be programmed prior to setting the corresponding
lock register bit. Setting the Password Protection Mode Lock Bit is programmed, a power cycle, hardware
reset, or PPB Lock Bit Set command is required to set the PPB Lock bit to 0 to protect the PPB array.
The programming time of the Lock Register is the same as the typical word programming time. During a Lock
Register programming EA, Data polling Status DQ6 Toggle Bit I will toggle until the programming has
completed. The system can also determine the status of the lock register programming by reading the Status
Register. See Status Register on page 37 for information on these status bits.
The user is not required to program DQ2 or DQ1, and DQ6 or DQ0 bits at the same time. This allows the user
to lock the SSR before or after choosing the device protection scheme. When programming the Lock Bits, the
Reserved Bits must be 1 (masked).
3.4.8
Persistent Protection Mode
The Persistent Protection method sets the PPB Lock to 1 during POR or Hardware Reset so that the PPB bits
are unprotected by a device reset. There is a command to clear the PPB Lock bit to 0 to protect the PPB.
There is no command in the Persistent Protection method to set the PPB Lock bit to 1 therefore the PPB Lock
bit will remain at 0 until the next power-off or hardware reset.
3.4.9
3.4.9.1
Password Protection Mode
PPB Password Protection Mode
PPB Password Protection Mode allows an even higher level of security than the Persistent Sector Protection
Mode, by requiring a 64-bit password for setting the PPB Lock. In addition to this password requirement, after
power up and reset, the PPB Lock is cleared to 0 to ensure protection at power-up. Successful execution of
the Password Unlock command by entering the entire password sets the PPB Lock to 1, allowing for sector
PPB modifications.
Password Protection Notes:
 The Password Program Command is only capable of programming 0’s.
 The password is all 1’s when shipped from Spansion. It is located in its own memory space and is
accessible through the use of the Password Program and Password Read commands.
 All 64-bit password combinations are valid as a password.
 Once the Password is programmed and verified, the Password Mode Locking Bit must be set in order to
prevent reading or modification of the password.
 The Password Mode Lock Bit, once programmed, prevents reading the 64-bit password on the data bus
and further password programming. All further program and read commands to the password region are
disabled (data is read as 1's) and these commands are ignored. There is no means to verify what the
password is after the Password Protection Mode Lock Bit is programmed. Password verification is only
allowed before selecting the Password Protection mode.
 The Password Mode Lock Bit is not erasable.
 The exact password must be entered in order for the unlocking function to occur.
 The addresses can be loaded in any order but all 4 words are required for a successful match to occur.
 The Sector Addresses and Word Line Addresses are compared while the password address/data are
loaded. If the Sector Adddress don't match than the error will be reported at the end of that write cycle. The
status register will return to the ready state with the Program Status Bit set to 1, Program Status Register
Bit set to 1, and Write Buffer Abort Status Bit set to 1 indicating a failed programming operation. It is a
failure to change the state of the PPB Lock bit because it is still protected by the lack of a valid password.
The data polling status will remain active, with DQ7 set to the complement of the DQ7 bit in the last word of
the password unlock command, and DQ6 toggling. RY/BY# will remain low.
22
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
 The specific address and data are compared after the Program Buffer To Flash command has been given.
If they don't match to the internal set value than the status register will return to the ready state with the
Program Status Bit set to 1 and Program Status Register Bit set to 1 indicating a failed programming
operation. It is a failure to change the state of the PPB Lock bit because it is still protected by the lack of a
valid password. The data polling status will remain active, with DQ7 set to the complement of the DQ7 bit in
the last word of the password unlock command, and DQ6 toggling. RY/BY# will remain low.
 The device requires approximately 100 µs for setting the PPB Lock after the valid 64-bit password is given
to the device.
 The Password Unlock command cannot be accepted any faster than once every 100 µs ± 20 µs. This
makes it take an unreasonably long time (58 million years) for a hacker to run through all the 64-bit
combinations in an attempt to correctly match a password. The EA status checking methods may be used
to determine when the EAC is ready to accept a new password command.
 If the password is lost after setting the Password Mode Lock Bit, there is no way to clear the PPB Lock.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
23
D at a
4.
4.1
S hee t
Read Operations
Asynchronous Read
Each read access may be made to any location in the memory (random access). Each random access is selftimed with the same latency from CE# or address to valid data (tACC or tCE).
4.2
Page Mode Read
Each random read accesses an entire 32-byte Page in parallel. Subsequent reads within the same Page
have faster read access speed. The Page is selected by the higher address bits (AMAX-A4), while the specific
word of that page is selected by the least significant address bits A3-A0. The higher address bits are kept
constant and only A3-A0 changed to select a different word in the same Page. This is an asynchronous
access with data appearing on DQ15-DQ0 when CE# remains Low, OE# remains Low, and the
asynchronous Page access time (tPACC) is satisfied. If CE# goes High and returns Low for a subsequent
access, a random read access is performed and time is required (tACC or tCE).
24
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
5.
She et
Embedded Operations
5.1
Embedded Algorithm Controller (EAC)
The EAC takes commands from the host system for programming and erasing the flash memory array and
performs all the complex operations needed to change the non-volatile memory state. This frees the host
system from any need to manage the program and erase processes.
There are four EAC operation categories:
 Standby (Read Mode)
 Address Space Switching
 Embedded Algorithms (EA)
 Advanced Sector Protection (ASP) Management
5.1.1
EAC Standby
In the standby mode current consumption is greatly reduced. The EAC enters its standby mode when no
command is being processed and no Embedded Algorithm is in progress. If the device is deselected
(CE# = High) during an Embedded Algorithm, the device still draws active current until the operation is
completed (ICC3). ICC4 in DC Characteristics on page 74 represents the standby current specification when
both the Host Interface and EAC are in their Standby state.
5.1.2
Address Space Switching
Writing specific address and data sequences (command sequences) switch the memory device address
space from the main flash array to one of the Address Space Overlays (ASO).
Embedded Algorithms operate on the information visible in the currently active (entered) ASO. The system
continues to have access to the ASO until the system issues an ASO Exit command, performs a Hardware
RESET, or until power is removed from the device. An ASO Exit Command switches from an ASO back to the
main flash array address space. The commands accepted when a particular ASO is entered are listed
between the ASO enter and exit commands in the command definitions table. See Command Summary
on page 57 for address and data requirements for all command sequences.
5.1.3
Embedded Algorithms (EA)
Changing the non-volatile data in the memory array requires a complex sequence of operations that are
called Embedded Algorithms (EA). The algorithms are managed entirely by the device internal Embedded
Algorithm Controller (EAC). The main algorithms perform programming and erasing of the main array data
and the ASO’s. The host system writes command codes to the flash device address space. The EAC
receives the commands, performs all the necessary steps to complete the command, and provides status
information during the progress of an EA.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
25
D at a
5.2
S hee t
Program and Erase Summary
Flash data bits are erased in parallel in a large group called a sector. The Erase operation places each data
bit in the sector in the logical 1 state (High). Flash data bits may be individually programmed from the erased
1 state to the programmed logical 0 (low) state. A data bit of 0 cannot be programmed back to a 1. A
succeeding read shows that the data is still 0. Only erase operations can convert a 0 to a 1. Programming the
same word location more than once with different 0 bits will result in the logical AND of the previous data and
the new data being programmed.
The duration of program and erase operations is shown in Embedded Algorithm Performance Table
on page 46.
Program and erase operations may be suspended.
 An erase operation may be suspended to allow either programming or reading of another sector (not in the
erase sector). No other erase operation can be started during an erase suspend.
 A program operation may be suspended to allow reading of another location (not in the Line being
programmed).
 No other program or erase operation may be started during a suspended program operation - program or
erase commands will be ignored during a suspended program operation.
 After an intervening program operation or read access is complete the suspended erase or program
operation may be resumed. The resume can happen at any time after the suspend assuming the device is
not in the process of executing another command.
 Program and Erase operations may be interrupted as often as necessary but in order for a program or
erase operation to progress to completion there must be some periods of time between resume and the
next suspend commands greater than or equal to tPRS or tERS in Embedded Algorithm Performance Table
on page 46.
 When an Embedded Algorithm (EA) is complete, the EAC returns to the operation state and address space
from which the EA was started (Erase Suspend or EAC Standby).
The system can determine the status of a program or erase operation by reading the Status Register or using
Data Polling Status. Refer to Status Register on page 37 for information on these status bits. Refer to Data
Polling Status on page 38 for more information.
Any commands written to the device during the Embedded Program Algorithm are ignored except the
Program Suspend, and Status Read command.
Any commands written to the device during the Embedded Erase Algorithm are ignored except Erase
Suspend and Status Read command.
A hardware reset immediately terminates any in progress program / erase operation and returns to read
mode after tRPH time. The terminated operation should be reinitiated once the device has returned to the idle
state, to ensure data integrity.
For performance and reliability reasons reading and programming is internally done on full 32-byte Pages.
ICC3 in DC Characteristics on page 74 represents the active current specification for a write (Embedded
Algorithm) operation.
5.2.1
Program Granularity
The S29GL-S supports two methods of programming, Word or Write Buffer Programming. Each Page can be
programmed by either method. Pages programmed by different methods may be mixed within a Line for the
Industrial Temperature version (-40°C to +85°C). For the In-Cabin version (-40°C to +105°C) the device will
only support one programming operation on each 32-byte page between erase operations and Single Word
Programming command is not supported.
Word programming examines the data word supplied by the command and programs 0’s in the addressed
memory array word to match the 0’s in the command data word.
Write Buffer Programming examines the write buffer and programs 0’s in the addressed memory array Pages
to match the 0’s in the write buffer. The write buffer does not need to be completely filled with data. It is
allowed to program as little as a single bit, several bits, a single word, a few words, a Page, multiple Pages, or
the entire buffer as one programming operation. Use of the write buffer method reduces host system
26
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
overhead in writing program commands and reduces memory device internal overhead in programming
operations to make Write Buffer Programming more efficient and thus faster than programming individual
words with the Word Programming command.
5.2.2
Incremental Programming
The same word location may be programmed more than once, by either the Word or Write Buffer
Programming methods, to incrementally change 1’s to 0’s.
5.3
Command Set
5.3.1
5.3.1.1
Program Methods
Word Programming
Word programming is used to program a single word anywhere in the main Flash Memory Array.
The Word Programming command is a four-write-cycle sequence. The program command sequence is
initiated by writing two unlock write cycles, followed by the program set up command. The program address
and data are written next, which in turn initiate the Embedded Word Program algorithm. The system is not
required to provide further controls or timing. The device automatically generates the program pulses and
verifies the programmed cell margin internally. When the Embedded Word Program algorithm is complete,
the EAC then returns to its standby mode.
The system can determine the status of the program operation by using Data Polling Status, reading the
Status Register, or monitoring the RY/BY# output. See Status Register on page 37 for information on these
status bits. See Data Polling Status on page 38 for information on these status bits. See Figure 5.1
on page 27 for a diagram of the programming operation.
Any commands other than Program Suspend written to the device during the Embedded Program algorithm
are ignored. Note that a hardware reset (RESET# = VIL) immediately terminates the programming operation
and returns the device to read mode after tRPH time. To ensure data integrity, the Program command
sequence should be reinitiated once the device has completed the hardware reset operation.
A modified version of the Word Programming command, without unlock write cycles, is used for programming
when entered into the Lock Register, Password, and PPB ASOs. The same command is used to change
volatile bits when entered in to the PPB Lock, and DYB ASOs. See Table 6.1 on page 57 for program
command sequences.
Figure 5.1 Word Program Operation
START
Write Program Command
Sequence
Data Poll from System
Embedded
Program
algorithm
in progress
Verify Word?
No
Yes
No
Last Addresss?
Increment Address
Yes
Programming Completed
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
27
D at a
5.3.1.2
S hee t
Write Buffer Programming
A write buffer is used to program data within a 512-byte address range aligned on a 512-byte boundary
(Line). Thus, a full Write Buffer Programming operation must be aligned on a Line boundary. Programming
operations of less than a full 512 bytes may start on any word boundary but may not cross a Line boundary.
At the start of a Write Buffer programming operation all bit locations in the buffer are all 1’s (FFFFh words)
thus any locations not loaded will retain the existing data. See Product Overview on page 10 for information
on address map.
Write Buffer Programming allows up to 512 bytes to be programmed in one operation. It is possible to
program from 1 bit up to 512 bytes in each Write Buffer Programming operation. It is recommended that a
multiple of Pages be written and each Page written only once. For the very best performance, programming
should be done in full Lines of 512 bytes aligned on 512-byte boundaries.
Write Buffer Programming is supported only in the main flash array or the SSR ASO.
The Write Buffer Programming operation is initiated by first writing two unlock cycles. This is followed by a
third write cycle of the Write to Buffer command with the Sector Address (SA), in which programming is to
occur. Next, the system writes the number of word locations minus 1. This tells the device how many write
buffer addresses are loaded with data and therefore when to expect the Program Buffer to flash confirm
command. The Sector Address must match in the Write to Buffer command and the Write Word Count
command. The Sector to be programmed must be unlocked (unprotected).
The system then writes the starting address / data combination. This starting address is the first address /
data pair to be programmed, and selects the write-buffer-Line address. The Sector address must match the
Write to Buffer Sector Address or the operation will abort and return to the initiating state. All subsequent
address / data pairs must be in sequential order. All write buffer addresses must be within the same Line. If
the system attempts to load data outside this range, the operation will abort and return to the initiating state.
The counter decrements for each data load operation. Note that while counting down the data writes, every
write is considered to be data being loaded into the write buffer. No commands are possible during the write
buffer loading period. The only way to stop loading the write buffer is to write with an address that is outside
the Line of the programming operation. This invalid address will immediately abort the Write to Buffer
command.
Once the specified number of write buffer locations has been loaded, the system must then write the Program
Buffer to Flash command at the Sector Address. The device then goes busy. The Embedded Program
algorithm automatically programs and verifies the data for the correct data pattern. The system is not required
to provide any controls or timings during these operations. If an incorrect number of write buffer locations
have been loaded the operation will abort and return to the initiating state. The abort occurs when anything
other than the Program Buffer to Flash is written when that command is expected at the end of the word
count.
The write-buffer embedded programming operation can be suspended using the Program Suspend
command. When the Embedded Program algorithm is complete, the EAC then returns to the EAC standby or
Erase Suspend standby state where the programming operation was started.
The system can determine the status of the program operation by using Data Polling Status, reading the
Status Register, or monitoring the RY/BY# output. See Status Register on page 37 for information on these
status bits. See Data Polling Status on page 38 for information on these status bits. See Figure 5.2
on page 29 for a diagram of the programming operation.
The Write Buffer Programming Sequence will be Aborted under the following conditions:
 Load a Word Count value greater than the buffer size (255).
 Write an address that is outside the Line provided in the Write to Buffer command.
 The Program Buffer to Flash command is not issued after the Write Word Count number of data words is
loaded.
When any of the conditions that cause an abort of write buffer command occur the abort will happen
immediately after the offending condition, and will indicate a Program Fail in the Status Register at bit location
4 (PSB = 1) due to Write Buffer Abort bit location 3 (WBASB = 1). The next successful program operation will
clear the failure status or a Clear Status Register may be issued to clear the PSB status bit.
The Write Buffer Programming Sequence can be stopped by the following: Hardware Reset or Power cycle.
However, these using either of these methods may leave the area being programmed in an intermediate state
28
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
with invalid or unstable data values. In this case the same area will need to be reprogrammed with the same
data or erased to ensure data values are properly programmed or erased.
Figure 5.2 Write Buffer Programming Operation with Data Polling Status
Write “Write to Buffer”
command Sector Address
Write “Word Count”
to program - 1 (WC)
Sector Address
Write Starting Address/Data
Yes
WC = 0?
Write to a different
Sector Address
No
ABORT Write to
Buffer Operation?
Yes
Write to Buffer ABORTED.
Must write “Write-to-Buffer
ABORT RESET”
command sequence to
return to READ mode.
No
Write next Address/Data pair
(Note 4)
WC = WC - 1
Write Program Buffer to Flash
Confirm, Sector Address
Read DQ7-DQ0 with
Addr = LAST LOADED ADDRESS
Yes
DQ7 = Data?
No
No
No
DQ1 = 1?
Yes
DQ5 = 1?
Yes
Read DQ7-DQ0 with
Addr = LAST LOADED ADDRESS
Yes
DQ7 = Data?
No
FAIL or ABORT
(Note 2)
PASS
Notes:
1. DQ7 should be rechecked even if DQ5 = 1 because DQ7 may change simultaneously with DQ5.
2. If this flowchart location was reached because DQ5 = 1, then the device FAILED. If this flowchart location was reached because DQ1 = 1,
then the Write Buffer operation was ABORTED. In either case the proper RESET command must be written to the device to return the
device to READ mode. Write-Buffer-Programming-Abort-Rest if DQ1 = 1, either Software RESET or Write-Buffer-Programming-AbortReset if DQ5 = 1.
3. See Table 6.1, Command Definitions on page 57 for the command sequence as required for Write Buffer Programming.
4. When Sector Address is specified, any address in the selected sector is acceptable. However, when loading Write-Buffer address
locations with data, all addresses MUST fall within the selected Write-Buffer Page.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
29
D at a
S hee t
Figure 5.3 Write Buffer Programming Operation with Status Register
Write “Write to Buffer”
command Sector Address
Write “Word Count”
to program - 1 (WC)
Sector Address
Write Starting Address/Data
Yes
WC = 0?
Write to a different
Sector Address
No
ABORT Write to
Buffer Operation?
Yes
Write to Buffer ABORTED.
Must write “Write-to-Buffer
ABORT RESET”
command sequence to
return to READ mode.
No
(Note 2)
Write next Address/Data pair
WC = WC - 1
Write Program Buffer to Flash
Confirm, Sector Address
Read Status Register
DRB
SR[7] = 0?
Yes
No
PSB
SR[4] = 0?
Yes
No
Program Fail
Yes
Program Successful
WBASB
SR[3] = 1?
No
SLSB
SR[1] = 0?
Yes
No
Program aborted during
Write to Buffer command
Sector Locked Error
Program Fail
Notes:
1. See Table 6.1, Command Definitions on page 57 for the command sequence as required for Write Buffer Programming.
2. When Sector Address is specified, any address in the selected sector is acceptable. However, when loading Write-Buffer address
locations with data, all addresses MUST fall within the selected Write-Buffer Page.
30
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Table 5.1 Write Buffer Programming Command Sequence
Sequence
Address
Data
Comment
Issue Unlock Command 1
555/AAA
AA
Issue Unlock Command 2
2AA/555
55
Issue Write to Buffer Command at Sector
Address
SA
0025h
Issue Number of Locations at Sector
Address
SA
WC
WC = number of words to program - 1
Starting
Address
PD
Selects Write-Buffer-Page and loads first Address/Data Pair.
Load next Address / Data pair
WBL
PD
All addresses MUST be within the selected write-bufferpage boundaries, and have to be loaded in sequential order.
Load LAST Address/Data pair
WBL
PD
All addresses MUST be within the selected write-bufferpage boundaries, and have to be loaded in sequential order.
SA
0029h
Example: WC of 0 = 1 words to pgm
WC of 1 = 2 words to pgm
Load Starting Address / Data pair
Issue Write Buffer Program Confirm at
Sector Address
This command MUST follow the last write buffer location
loaded, or the operation will ABORT.
Device goes busy.
Legend:
SA = Sector Address (Non-Sector Address bits are don't care. Any address within the Sector is sufficient.)
WBL = Write Buffer Location (MUST be within the boundaries of the Write-Buffer-Line specified by the Starting Address.)
WC =Word Count
PD = Program Data
5.3.2
Program Suspend / Program Resume Commands
The Program Suspend command allows the system to interrupt an embedded programming operation so that
data can read from any non-suspended Line. When the Program Suspend command is written during a
programming process, the device halts the programming operation within tPSL (program suspend latency)
and updates the status bits. Addresses are don't-cares when writing the Program Suspend command.
There are two commands available for program suspend. The legacy combined Erase / Program suspend
command (B0h command code) and the separate Program Suspend command (51h command code). There
are also two commands for Program resume. The legacy combined Erase / Program resume command (30h
command code) and the separate Program Resume command (50h command code). It is recommended to
use the separate program suspend and resume commands for programming and use the legacy combined
command only for erase suspend and resume.
After the programming operation has been suspended, the system can read array data from any nonsuspended Line. The Program Suspend command may also be issued during a programming operation while
an erase is suspended. In this case, data may be read from any addresses not in Erase Suspend or Program
Suspend.
After the Program Resume command is written, the device reverts to programming and the status bits are
updated. The system can determine the status of the program operation by reading the Status Register or
using Data Polling. Refer to Status Register on page 37 for information on these status bits. Refer to Data
Polling Status on page 38 for more information.
Accesses and commands that are valid during Program Suspend are:
 Read to any other non-erase-suspended sector
 Read to any other non-program-suspended Line
 Status Read command
 Exit ASO or Command Set Exit
 Program Resume command
The system must write the Program Resume command to exit the Program Suspend mode and continue the
programming operation. Further writes of the Program Resume command are ignored. Another Program
Suspend command can be written after the device has resumed programming.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
31
D at a
S hee t
Program operations can be interrupted as often as necessary but in order for a program operation to progress
to completion there must be some periods of time between resume and the next suspend command greater
than or equal to tPRS in Embedded Algorithm Controller (EAC) on page 25.
Program suspend and resume is not supported while entered in an ASO. While in program suspend entry into
ASO is not supported.
5.3.3
Blank Check
The Blank Check command will confirm if the selected main flash array sector is erased. The Blank Check
command does not allow for reads to the array during the Blank Check. Reads to the array while this
command is executing will return unknown data.
To initiate a Blank Check on a Sector, write 33h to address 555h in the Sector, while the EAC is in the
standby state
The Blank Check command may not be written while the device is actively programming or erasing or
suspended.
Use the Status Register read to confirm if the device is still busy and when complete if the sector is blank or
not. Bit 7 of the Status Register will show if the device is performing a Blank Check (similar to an erase
operation). Bit 5 of the Status Register will be cleared to 0 if the sector is erased and set to 1 if not erased.
As soon as any bit is found to not be erased, the device will halt the operation and report the results.
Once the Blank Check is completed, the EAC will return to the Standby State.
5.3.4
5.3.4.1
Erase Methods
Chip Erase
The chip erase function erases the entire main Flash Memory Array. The device does not require the system
to preprogram prior to erase. The Embedded Erase algorithm automatically programs and verifies the entire
memory for an all 0 data pattern prior to electrical erase. After a successful chip erase, all locations within the
device contain FFFFh. The system is not required to provide any controls or timings during these operations.
The chip erase command sequence is initiated by writing two unlock cycles, followed by a set up command.
Two additional unlock write cycles are then followed by the chip erase command, which in turn invokes the
Embedded Erase algorithm. When WE# goes high, at the end of the 6th cycle, the RY/BY# goes low.
When the Embedded Erase algorithm is complete, the EAC returns to the standby state. Note that while the
Embedded Erase operation is in progress, the system can not read data from the device. The system can
determine the status of the erase operation by reading RY/BY#, the Status Register or using Data Polling.
Refer to Status Register on page 37 for information on these status bits. Refer to Data Polling Status
on page 38 for more information.
Once the chip erase operation has begun, only a Status Read, Hardware RESET or Power cycle are valid. All
other commands are ignored. However, a Hardware Reset or Power Cycle immediately terminates the erase
operation and returns to read mode after tRPH time. If a chip erase operation is terminated, the chip erase
command sequence must be reinitiated once the device has returned to the idle state to ensure data integrity.
See Table 5.4 on page 46, Asynchronous Write Operations on page 83 and Alternate CE# Controlled Write
Operations on page 89 for parameters and timing diagrams.
Sectors protected by the ASP DYB and PPB lock bits will not be erased. See ASP on page 19. If a sector is
protected during chip erase, chip erase will skip the protected sector and continue with next sector erase. The
status register erase status bit and sector lock bit are not set to 1 by a failed erase on a protected sector.
32
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
5.3.4.2
She et
Sector Erase
The sector erase function erases one sector in the memory array. The device does not require the system to
preprogram prior to erase. The Embedded Erase algorithm automatically programs and verifies the entire
sector for an all 0 data pattern prior to electrical erase. After a successful sector erase, all locations within the
erased sector contain FFFFh. The system is not required to provide any controls or timings during these
operations. The sector erase command sequence is initiated by writing two unlock cycles, followed by a set
up command. Two additional unlock write cycles are then followed by the address of the sector to be erased,
and the sector erase command. When WE# goes high, at the end of the 6th cycle, the RY/BY# goes low.
The system can determine the status of the erase operation by reading the Status Register or using Data
Polling. Refer to Status Register on page 37 for information on these status bits. Refer to Data Polling Status
on page 38 for more information.
Once the sector erase operation has begun, the Status Register Read and Erase Suspend commands are
valid. All other commands are ignored. However, note that a hardware reset immediately terminates the
erase operation and returns to read mode after tRPH time. If a sector erase operation is terminated, the sector
erase command sequence must be reinitiated once the device has reset operation to ensure data integrity.
See Embedded Algorithm Controller (EAC) on page 25 for parameters and timing diagrams.
Sectors protected by the ASP DYB and PPB lock bits will not be erased. See ASP on page 19.
Figure 5.4 Sector Erase Operation
Write Unlock Cycles:
Address 555h, Data AAh
Address 2AAh, Data 55h
Unlock Cycle 1
Unlock Cycle 2
Write Sector Erase Cycles:
Address 555h, Data 80h
Address 555h, Data AAh
Address 2AAh, Data 55h
Sector Address, Data 30h
Command Cycle 1
Command Cycle 2
Command Cycle 3
Specify first sector for erasure
Perform Write Operation
Status Algorithm
Yes
Status may be obtained by Status Register Polling
or Data Polling methods.
Done?
No
Erase Error?
No
Error condition (Exceeded Timing Limits)
Yes
PASS. Device returns
to reading array.
October 9, 2013 S29GL_128S_01GS_00_08
FAIL. Write reset command
to return to reading array.
GL-S MirrorBit® Family
33
D at a
5.3.5
S hee t
Erase Suspend / Erase Resume
The Erase Suspend command allows the system to interrupt a sector erase operation and then read data
from, or program data to, the main flash array. This command is valid only during sector erase or program
operation. The Erase Suspend command is ignored if written during the chip erase operation.
When the Erase Suspend command is written during the sector erase operation, the device requires a
maximum of tESL (erase suspend latency) to suspend the erase operation and update the status bits.
After the erase operation has been suspended, the part enters the erase-suspend mode. The system can
read data from or program data to the main flash array. Reading at any address within erase-suspended
sectors produces undetermined data. The system can determine if a sector is actively erasing or is erasesuspended by reading the Status Register or using Data Polling. Refer to Status Register on page 37 for
information on these status bits. Refer to Data Polling Status on page 38 for more information.
After an erase-suspended program operation is complete, the EAC returns to the erase-suspend state. The
system can determine the status of the program operation by reading the Status Register, just as in the
standard program operation.
If a program failure occurs during erase suspend the Clear or Reset commands will return the device to the
erase suspended state. Erase will need to be resumed and completed before again trying to program the
memory array.
Accesses and commands that are valid during Erase Suspend are:
 Read to any other non-suspended sector
 Program to any other non-suspended sector
 Status Register Read
 Status Register Clear
 Enter DYB ASO
 DYB Set
 DYB Clear
 DYB Status Read
 Exit ASO or Command Set Exit
 Erase Resume command
To resume the sector erase operation, the system must write the Erase Resume command. The device will
revert to erasing and the status bits will be updated. Further writes of the Resume command are ignored.
Another Erase Suspend command can be written after the chip has resumed erasing.
Erase suspend and resume is not supported while entered in an ASO. While in erase suspend entry into ASO
is not supported.
34
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
5.3.6
5.3.6.1
She et
ASO Entry and Exit
ID-CFI ASO
The system can access the ID-CFI ASO by issuing the ID-CFI Entry command sequence during Read Mode.
This entry command uses the Sector Address (SA) in the command to determine which sector will be overlaid
and which sector's protection state is reported in word location 2h. See the detail description Table 6.2
on page 60.
The ID-CFI ASO allows the following activities:
 Read ID-CFI ASO, using the same SA as used in the entry command.
 Read Sector Protection State at Sector Address (SA) + 2h. Location 2h provides volatile information on the
current state of sector protection for the sector addressed. Bit 0 of the word at location 2h shows the logical
NAND of the PPB and DYB bits related to the addressed sector such that if the sector is protected by either
the PPB=0 or the DYB=0 bit for that sector the state shown is protected. (1= Sector protected, 0= Sector
unprotected). This protection state is shown only for the SA selected when entering ID-CFI ASO. Reading
other SA provides undefined data. To read a different SA protection state ASO exit command must be used
and then enter ID-CFI ASO again with the new SA.
 ASO Exit.
The following is a C source code example of using the CFI Entry and Exit functions. Refer to the Spansion
Low Level Driver User's Guide (available on www.spansion.com) for general information on Spansion flash
memory software development guidelines.
/* Example: CFI Entry command */
*( (UINT16 *)base_addr + 0x55 ) = 0x0098; /* write CFI entry command */
/* Example: CFI Exit command */
*( (UINT16 *)base_addr + 0x000 ) = 0x00F0; /* write cfi exit command */
5.3.6.2
Status Register ASO
The Status Register ASO contains a single word of registered volatile status for Embedded Algorithms. When
the Status Register read command is issued, the current status is captured (by the rising edge of WE#) into
the register and the ASO is entered. The Status Register content appears on all word locations. The first read
access exits the Status Register ASO (with the rising edge of CE# or OE#) and returns to the address space
map in use when the Status Register read command was issued. Write commands will not exit the Status
Register ASO state.
5.3.6.3
Secure Silicon Region ASO
The system can access the Secure Silicon Region by issuing the Secure Silicon Region Entry command
sequence during Read Mode. This entry command uses the Sector Address (SA) in the command to
determine which sector will be overlaid.
The Secure Silicon Region ASO allows the following activities:
 Read Secure Silicon Regions.
 Programming the customer Secure Silicon Region is allowed using the Word or Write Buffer Programming
commands.
 ASO Exit using legacy Secure Silicon Exit command for backward software compatibility.
 ASO Exit using the common exit command for all ASO - alternative for a consistent exit method.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
35
D at a
5.3.6.4
S hee t
Lock Register ASO
The system can access the Lock Register by issuing the Lock Register entry command sequence during
Read Mode. This entry command does not use a sector address from the entry command. The Lock Register
appears at word location 0 in the device address space. All other locations in the device address space are
undefined.
The Lock Register ASO allows the following activities:
 Read Lock Register, using device address location 0.
 Program the customer Lock Register using a modified Word Programming command.
 ASO Exit using legacy Command Set Exit command for backward software compatibility.
 ASO Exit using the common exit command for all ASO - alternative for a consistent exit method.
5.3.6.5
Password ASO
The system can access the Password ASO by issuing the Password entry command sequence during Read
Mode. This entry command does not use a sector address from the entry command. The Password appears
at word locations 0 to 3 in the device address space. All other locations in the device address space are
undefined.
The Password ASO allows the following activities:
 Read Password, using device address location 0 to 3.
 Program the Password using a modified Word Programming command.
 Unlock the PPB Lock bit with the Password Unlock command.
 ASO Exit using legacy Command Set Exit command for backward software compatibility.
 ASO Exit using the common exit command for all ASO - alternative for a consistent exit method.
5.3.6.6
PPB ASO
The system can access the PPB ASO by issuing the PPB entry command sequence during Read Mode. This
entry command does not use a sector address from the entry command. The PPB bit for a sector appears in
bit 0 of all word locations in the sector.
The PPB ASO allows the following activities:
 Read PPB protection status of a sector in bit 0 of any word in the sector.
 Program the PPB bit using a modified Word Programming command.
 Erase all PPB bits with the PPB erase command.
 ASO Exit using legacy Command Set Exit command for backward software compatibility.
 ASO Exit using the common exit command for all ASO - alternative for a consistent exit method.
5.3.6.7
PPB Lock ASO
The system can access the PPB Lock ASO by issuing the PPB Lock entry command sequence during Read
Mode. This entry command does not use a sector address from the entry command. The global PPB Lock bit
appears in bit 0 of all word locations in the device.
The PPB Lock ASO allows the following activities:
 Read PPB Lock protection status in bit 0 of any word in the device address space.
 Set the PPB Lock bit using a modified Word Programming command.
 ASO Exit using legacy Command Set Exit command for backward software compatibility.
 ASO Exit using the common exit command for all ASO - alternative for a consistent exit method.
36
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
5.3.6.8
She et
DYB ASO
The system can access the DYB ASO by issuing the DYB entry command sequence during Read Mode. This
entry command does not use a sector address from the entry command. The DYB bit for a sector appears in
bit 0 of all word locations in the sector.
The DYB ASO allows the following activities:
 Read DYB protection status of a sector in bit 0 of any word in the sector.
 Set the DYB bit using a modified Word Programming command.
 Clear the DYB bit using a modified Word Programming command.
 ASO Exit using legacy Command Set Exit command for backward software compatibility.
 ASO Exit using the common exit command for all ASO - alternative for a consistent exit method.
5.3.6.9
Software (Command) Reset / ASO exit
Software reset is part of the command set (See Table 6.1, Command Definitions on page 57) that also
returns the EAC to standby state and must be used for the following conditions:
 Exit ID/CFI mode
 Clear timeout bit (DQ5) for data polling when timeout occurs
Software Reset does not affect EA mode. Reset commands are ignored once programming or erasure has
begun, until the operation is complete. Software Reset does not affect outputs; it serves primarily to return to
Read Mode from an ASO mode or from a failed program or erase operation.
Software Reset may cause a return to Read Mode from undefined states that might result from invalid
command sequences. However, a Hardware Reset may be required to return to normal operation from some
undefined states.
There is no software reset latency requirement. The reset command is executed during the tWPH period.
5.4
Status Monitoring
There are three methods for monitoring EA status. Previous generations of the S29GL flash family used the
methods called Data Polling and Ready/Busy# (RY/BY#) Signal. These methods are still supported by the
S29GL-S family. One additional method is reading the Status Register.
5.4.1
Status Register
The status of program and erase operations is provided by a single 16-bit status register. The status is
receiver by writing the Status Register Read command followed by a read access. When the Status Register
read command is issued, the current status is captured (by the rising edge of WE#) into the register and the
ASO is entered. The contents of the status register is aliased (overlaid) on the full memory address space.
Any valid read (CE# and OE# low) access while in the Status Register ASO will exit the ASO (with the rising
edge of CE# or OE# for tCEPH/tOEPH time) and return to the address space map in use when the Status
Register Read command was issued.
The status register contains bits related to the results - success or failure - of the most recently completed
Embedded Algorithms (EA):
 Erase Status (bit 5),
 Program Status (bit 4),
 Write Buffer Abort (bit 3),
 Sector Locked Status (bit 1),
 RFU (bit 0).
and, bits related to the current state of any in process EA:
 Device Busy (bit 7),
 Erase Suspended (bit 6),
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
37
D at a
S hee t
 Program Suspended (bit 2),
The current state bits indicate whether an EA is in process, suspended, or completed.
The upper 8 bits (bits 15:8) are reserved. These have undefined High or Low value that can change from one
status read to another. These bits should be treated as don't care and ignored by any software reading status.
The Soft Reset Command will clear to 0 bits [5, 4, 1, 0] of the status register if Status Register bit 3 =0. It will
not affect the current state bits. The Clear Status Register Command will clear to 0 the results related bits of
the status register but will not affect the current state bits.
Table 5.2 Status Register
Bit #
Bit
Description
15:8
Reserved
Bit Name
7
6
Device
Ready Bit
Erase
Suspend
Status Bit
DRB
5
4
3
2
1
0
Erase
Status Bit
Program
Status Bit
Write Buffer
Abort
Status Bit
Program
Suspend
Status Bit
Sector Lock
Status Bit
Reserved
ESSB
ESB
PSB
WBASB
PSSB
SLSB
0
0
0
0
Invalid
Invalid
Invalid
Invalid
0=No
Program in
suspension
0=Sector
not locked
during
operation
Reset
Status
X
1
0
0
0
Busy Status
Invalid
0
Invalid
Invalid
Invalid
Ready
Status
X
1
0=No Erase
in
Suspension
0=Program
not aborted
0=Erase
successful
1=Erase in 1=Erase fail
Suspension
0=Program
successful
1=Program
fail
1=Program
aborted
during
Write to
Buffer
command
1=Program
in
suspension
X
1=Sector
locked error
Notes:
1. Bits 15 thru 8, and 0 are reserved for future use and may display as 0 or 1. These bits should be ignored (masked) when checking status.
2. Bit 7 is 1 when there is no Embedded Algorithm in progress in the device.
3. Bits 6 thru 1 are valid only if Bit 7 is 1.
4. All bits are put in their reset status by cold reset or warm reset.
5. Bits 5, 4, 3, and 1 are cleared to 0 by the Clear Status Register command or Reset command.
6. Upon issuing the Erase Suspend Command, the user must continue to read status until DRB becomes 1.
7. ESSB is cleared to 0 by the Erase Resume Command.
8. ESB reflects success or failure of the most recent erase operation.
9. PSB reflects success or failure of the most recent program operation.
10. During erase suspend, programming to the suspended sector, will cause program failure and set the Program status bit to 1.
11. Upon issuing the Program Suspend Command, the user must continue to read status until DRB becomes 1.
12. PSSB is cleared to 0 by the Program Resume Command.
13. SLSB indicates that a program or erase operation failed because the sector was locked.
14. SLSB reflects the status of the most recent program or erase operation.
5.4.2
Data Polling Status
During an active Embedded Algorithm the EAC switches to the Data Polling ASO to display EA status to any
read access. A single word of status information is aliased in all locations of the device address space. In the
status word there are several bits to determine the status of an EA. These are referred to as DQ bits as they
appear on the data bus during a read access while an EA is in progress. DQ bits 15 to 8, DQ4, and DQ0 are
reserved and provide undefined data. Status monitoring software must mask the reserved bits and treat them
as don't care. Table 5.3 on page 42 and the following subsections describe the functions of the remaining
bits.
38
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
5.4.2.1
She et
DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Algorithm is in progress or
has completed. Data# Polling is valid after the rising edge of the final WE# pulse in the program or erase
command sequence. Note that the Data# Polling is valid only for the last word being programmed in the writebuffer-page during Write Buffer Programming. Reading Data# Polling status on any word other than the last
word to be programmed in the write-buffer-page will return false status information.
During the Embedded Program algorithm, the device outputs on DQ7 the complement of the data bit
programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend. When the
Embedded Program algorithm is complete, the device outputs the data bit programmed to bit 7 of the last
word programmed. In case of a Program Suspend, the device allows only reading array data. If a program
address falls within a protected sector, Data# Polling on DQ7 is active for approximately 20 µs, then the
device returns to reading array data.
During the Embedded Erase or Blank Check algorithms, Data# Polling produces a 0 on DQ7. When the
algorithm is complete, or if the device enters the Erase Suspend mode, Data# Polling produces a 1 on DQ7.
This is analogous to the complement / true datum output described for the Embedded Program algorithm: the
erase function changes all the bits in a sector to 1; prior to this, the device outputs the complement or '0'. The
system must provide an address within the sector selected for erasure to read valid status information on
DQ7.
After an erase command sequence is written, if the sector selected for erasing is protected, Data# Polling on
DQ7 is active for approximately 100 µs, then the device returns to reading array data.
When the system detects DQ7 has changed from the complement to true data, it can read valid data at
DQ15-DQ0 on the following read cycles. This is because DQ7 may change asynchronously with DQ6-DQ0
while Output Enable (OE#) is asserted Low. This is illustrated in Figure 10.16 on page 88. Table 5.3
on page 42 shows the outputs for Data# polling on DQ7. Figure 5.2 on page 29 shows the Data# polling
algorithm use in Write Buffer Programming.
Valid DQ7 data polling status may only be read from:
 the address of the last word loaded into the Write Buffer for a Write Buffer programming operation;
 the location of a single word programming operation;
 or a location in a sector being erased or blank checked;
 or a location in any sector during chip erase.
Figure 5.5 Data# Polling Algorithm
START
Read DQ7-DQ0
-
DQ7 = Data?
Yes
No
No
DQ5 = 1?
Yes
Read DQ 7 -DQ0
DQ7 = Data?
Yes
No
FAIL
PASS
Note:
1. DQ7 should be rechecked even if DQ5 = 1 because DQ7 may change simultaneously with DQ5.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
39
D at a
5.4.2.2
S hee t
DQ6: Toggle Bit I
Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or complete,
or whether the device has entered the Program Suspend or Erase Suspend mode. Toggle Bit I may be read
at any address, and is valid after the rising edge of the final WE# pulse in the command sequence (prior to the
program or erase operation).
During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause
DQ6 to toggle. (The system may use either OE# or CE# to control the read cycles). When the operation is
complete, DQ6 stops toggling.
After an erase command sequence is written, if the sector selected for erasing is protected, DQ6 toggles for
approximately 100 µs, then the EAC returns to standby (Read Mode). If the selected sector is not protected,
the Embedded Erase algorithm erases the unprotected sector.
The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or erasesuspended. When the device is actively erasing (that is, the Embedded Erase algorithm is in progress), DQ6
toggles. When the device enters the Program Suspend mode or Erase Suspend mode, DQ6 stops toggling.
However, the system must also use DQ2 to determine which sectors are erasing, or erase-suspended.
Alternatively, the system can use DQ7 (see DQ7: Data# Polling on page 39).
DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embedded Program
algorithm is complete.
Table 5.3 on page 42 shows the outputs for Toggle Bit I on DQ6. Figure 5.6 on page 41 shows the toggle bit
algorithm in flowchart form, and the Reading Toggle Bits DQ6/DQ2 on page 41 explains the algorithm.
Figure 5.6 on page 41 shows the toggle bit timing diagrams. Figure 5.2 on page 29 shows the differences
between DQ2 and DQ6 in graphical form. See also DQ2: Toggle Bit II on page 40.
5.4.2.3
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the system may read DQ3 to determine whether or not
erasure has begun. See Sector Erase on page 33 for more details.
After the sector erase command is written, the system should read the status of DQ7 (Data# Polling) or DQ6
(Toggle Bit I) to ensure that the device has accepted the command sequence, and then read DQ3. If DQ3 is
1, the Embedded Erase algorithm has begun; all further commands (except Erase Suspend) are ignored until
the erase operation is complete. Table 5.3 on page 42 shows the status of DQ3 relative to the other status
bits.
5.4.2.4
DQ2: Toggle Bit II
Toggle Bit II on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing (that is,
the Embedded Erase algorithm is in progress), or whether that sector is erase-suspended. Toggle Bit II is
valid after the rising edge of the final WE# pulse in the command sequence.
DQ2 toggles when the system reads at addresses within the sector selected for erasure. (The system may
use either OE# or CE# to control the read cycles). But DQ2 cannot distinguish whether the sector is actively
erasing or is erase-suspended. DQ6, by comparison, indicates whether the device is actively erasing, or is in
Erase Suspend, but cannot distinguish if the sector is selected for erasure. Thus, both status bits are required
for sector and mode information. Refer to Table 5.3 on page 42 to compare outputs for DQ2 and DQ6.
Figure 5.5 on page 39 shows the toggle bit algorithm in flowchart form, and the Reading Toggle Bits DQ6/
DQ2 on page 41 explains the algorithm. See also Figure 5.6 on page 41 shows the toggle bit timing diagram.
Figure 5.2 on page 29 shows the differences between DQ2 and DQ6 in graphical form.
40
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
5.4.2.5
She et
Reading Toggle Bits DQ6/DQ2
Refer to Figure 5.5 on page 39 for the following discussion. Whenever the system initially begins reading
toggle bit status, it must read DQ7-DQ0 at least twice in a row to determine whether a toggle bit is toggling.
Typically, the system would note and store the value of the toggle bit after the first read. After the second
read, the system would compare the new value of the toggle bit with the previous value. If the toggle bit is not
toggling, the device has completed the program or erases operation. The system can read array data on
DQ15-DQ0 on the following read cycle.
However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the
system also should note whether the value of DQ5 is High (see DQ5: Exceeded Timing Limits on page 41). If
it is, the system should then determine again whether the toggle bit is toggling, since the toggle bit may have
stopped toggling just as DQ5 went High. If the toggle bit is no longer toggling, the device has successfully
completed the program or erase operation. If it is still toggling, the device did not complete the operation
successfully, and the system must write the reset command to return to reading array data.
The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has not
gone High. The system may continue to monitor the toggle bit and DQ5 through successive read cycles,
determining the status as described in the previous paragraph. Alternatively, it may choose to perform other
system tasks. In this case, the system must start at the beginning of the algorithm when it returns to
determine the status of the operation (top of Figure 5.6 on page 41).
Figure 5.6 Toggle Bit Program
START
Read DQ7 -DQ0
Read DQ7 -DQ0 (Note 1)
Toggle Bit
= Toggle?
No
Yes
No
DQ5 = 1?
Yes
Read DQ7 -DQ0 Twice (Notes 1, 2)
Toggle Bit
= Toggle?
No
Yes
Erase/Program
Operation Not
Complete
Erase/Program
Operation Complete
Notes:
1. Read toggle bit twice to determine whether or not it is toggling. See text.
2. Recheck toggle bit because it may stop toggling as DQ5 changes to 1. See text.
5.4.2.6
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has exceeded a specified internal pulse count limit. Under
these conditions DQ5 produces a 1. This is a failure condition that indicates the program or erase cycle was
not successfully completed. The system must issue the reset command to return the device to reading array
data.
When a timeout occurs, the software must send a reset command to clear the timeout bit (DQ5) and to return
the EAC to read array mode. In this case, it is possible that the flash will continue to communicate busy for up
to 2 µs after the reset command is sent.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
41
D at a
5.4.2.7
S hee t
DQ1: Write-to-Buffer Abort
DQ1 indicates whether a Write-to-Buffer operation was aborted. Under these conditions DQ1 produces a 1.
The system must issue the Write-to-Buffer-Abort-Reset command sequence to return the EAC to standby
(Read Mode) and the Status Register failed bits are cleared. See Write Buffer Programming on page 28 for
more details.
Table 5.3 Data Polling Status
DQ7
(Note 2)
DQ6
DQ5
(Note 1)
DQ3
DQ2
(Note 2)
DQ1
(Note 4)
RY/BY#
Embedded Program Algorithm
DQ7#
Toggle
0
N/A
No
Toggle
0
0
Reading within Erasing Sector
0
Toggle
0
1
Toggle
N/A
0
Reading Outside erasing Sector
0
Toggle
0
1
No
Toggle
N/A
0
INVALID
INVALID
INVALID
INVALID
INVALID
INVALID
(Not
Allowed)
(Not
Allowed)
(Not
Allowed)
(Not
Allowed)
(Not
Allowed)
(Not
Allowed)
1
Reading within Non-Program Suspended
Sector
Data
Data
Data
Data
Data
Data
1
Reading within Erase Suspended Sector
1
No
Toggle
0
N/A
Toggle
N/A
1
Reading within Non-Erase Suspend Sector
Data
Data
Data
Data
Data
Data
1
Programming within Non-Erase Suspended
Sector
DQ7#
Toggle
0
N/A
N/A
N/A
0
DQ7#
Toggle
0
N/A
No
Toggle
0
0
Operation
Standard
Mode
Program
Suspend
Mode
(Note 3)
Erase
Suspend
Mode
Reading within Program Suspended Sector
BUSY State
Write-toBuffer
Exceeded Timing Limits
(Notes 4, 5)
ABORT State
DQ7#
Toggle
1
N/A
N/A
0
0
DQ7#
Toggle
0
N/A
N/A
1
0
Notes:
1. DQ5 switches to '1' when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits. See DQ5:
Exceeded Timing Limits on page 41 for more information.
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details.
3. Data are invalid for addresses in a Program Suspended Line. All addresses other than the program suspended line can be read for valid
data.
4. DQ1 indicates the Write-to-Buffer ABORT status during Write-Buffer-Programming operations.
5. Applies only to program operations.
5.5
Error Types and Clearing Procedures
There are three types of errors reported by the embedded operation status methods. Depending on the error
type, the status reported and procedure for clearing the error status is different. Following is the clearing of
error status:
42

If an ASO was entered before the error the device remains entered in the ASO awaiting ASO read or
a command write.

If an erase was suspended before the error the device returns to the erase suspended state awaiting
flash array read or a command write.

Otherwise, the device will be in standby state awaiting flash array read or a command write.
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
5.5.1
She et
Embedded Operation Error
If an error occurs during an embedded operation (program, erase, blank check, or password unlock) the
device (EAC) remains busy. The RY/BY# output remains Low, data polling status continues to be overlaid on
all address locations, and the status register shows ready with valid status bits. The device remains busy until
the error status is detected by the host system status monitoring and the error status is cleared.
During embedded algorithm error status the Data Polling status will show the following:

DQ7 is the inversion of the DQ7 bit in the last word loaded into the write buffer or last word of the
password in the case of the password unlock command. DQ7 = 0 for an erase or blank check failure

DQ6 continues to toggle

DQ5 = 1; Failure of the embedded operation

DQ4 is RFU and should be treated as don’t care (masked)

DQ3 = 1 to indicate embedded sector erase in progress

DQ2 continues to toggle, independent of the address used to read status

DQ1 = 0; Write buffer abort error

DQ0 is RFU and should be treated as don’t care (masked)
During embedded algorithm error status the Status Register will show the following:

SR[7] = 1; Valid status displayed

SR[6] = X; May or may not be erase suspended during the EA error

SR[5] = 1 on erase or blank check error; else = 0

SR[4] = 1 on program or password unlock error; else = 0

SR[3] = 0; Write buffer abort

SR[2] = 0; Program suspended

SR[1] = 0; Protected sector

SR[0] = X; RFU, treat as don’t care (masked)
When the embedded algorithm error status is detected, it is necessary to clear the error status in order to
return to normal operation, with RY/BY# High, ready for a new read or command write. The error status can
be cleared by writing:

Reset command

Status Register Clear command
Commands that are accepted during embedded algorithm error status are:

Status Register Read

Reset command

Status Register Clear command
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
43
D at a
5.5.2
S hee t
Protection Error
If an embedded algorithm attempts to change data within a protected area (program, or erase of a protected
sector or OTP area) the device (EAC) goes busy for a period of 20 to 100 µs then returns to normal operation.
During the busy period the RY/BY# output remains Low, data polling status continues to be overlaid on all
address locations, and the status register shows not ready with invalid status bits (SR[7] = 0).
During the protection error status busy period the data polling status will show the following:

DQ7 is the inversion of the DQ7 bit in the last word loaded into the write buffer. DQ7 = 0 for an erase
failure

DQ6 continues to toggle, independent of the address used to read status

DQ5 = 0; to indicate no failure of the embedded operation during the busy period

DQ4 is RFU and should be treated as don’t care (masked)

DQ3 = 1 to indicate embedded sector erase in progress

DQ2 continues to toggle, independent of the address used to read status

DQ1 = 0; Write buffer abort error

DQ0 is RFU and should be treated as don’t care (masked)
Commands that are accepted during the protection error status busy period are:

Status Register Read
When the busy period ends the device returns to normal operation, the data polling status is no longer
overlaid, RY/BY# is High, and the status register shows ready with valid status bits. The device is ready for
flash array read or write of a new command.
After the protection error status busy period the Status Register will show the following:

SR[7] = 1; Valid status displayed

SR[6] = X; May or may not be erase suspended after the protection error busy period

SR[5] = 1 on erase error, else = 0

SR[4] = 1 on program error, else = 0

SR[3] = 0; Program not aborted

SR[2] = 0; No Program in suspension

SR[1] = 1; Error due to attempting to change a protected location

SR[0] = X; RFU, treat as don’t care (masked)
Commands that are accepted after the protection error status busy period are:

44
Any command
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
5.5.3
She et
Write Buffer Abort
If an error occurs during a Write to Buffer command the device (EAC) remains busy. The RY/BY# output
remains Low, data polling status continues to be overlaid on all address locations, and the status register
shows ready with valid status bits. The device remains busy until the error status is detected by the host
system status monitoring and the error status is cleared.
During write to buffer abort (WBA) error status the Data Polling status will show the following:

DQ7 is the inversion of the DQ7 bit in the last word loaded into the write buffer

DQ6 continues to toggle, independent of the address used to read status

DQ5 = 0; to indicate no failure of the programming operation. WBA is an error in the values input by
the Write to Buffer command before the programming operation can begin

DQ4 is RFU and should be treated as don’t care (masked)

DQ3 is don't care after program operation as no erase is in progress. If the Write Buffer Program
operation was started after an erase operation had been suspended then DQ3 = 1. If there was no
erase operation in progress then DQ3 is a don't care and should be masked.

DQ2 does not toggle after program operation as no erase is in progress. If the Write Buffer Program
operation was started after an erase operation had been suspended then DQ2 will toggle in the
sector where the erase operation was suspended and not in any other sector. If there was no erase
operation in progress then DQ2 is a don't care and should be masked.

DQ1 = 1: Write buffer abort error

DQ0 is RFU and should be treated as don’t care (masked)
During embedded algorithm error status the Status Register will show the following:

SR[7] = 1; Valid status displayed

SR[6] = X; May or may not be erase suspended during the WBA error status

SR[5] = 0; Erase successful

SR[4] = 1; Programming related error

SR[3] = 1; Write buffer abort

SR[2] = 0; No Program in suspension

SR[1] = 0; Sector not locked during operation

SR[0] = X; RFU, treat as don’t care (masked)
When the WBA error status is detected, it is necessary to clear the error status in order to return to normal
operation, with RY/BY# High, ready for a new read or command write. The error status can be cleared and
device returned to normal operation by writing:

Write Buffer Abort Reset command
–

Clears the status register and returns to normal operation
Status Register Clear command
Commands that are accepted during embedded algorithm error status are:

Status Register Read

Write Buffer Abort Reset command

Status Register Clear command
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
45
D at a
5.6
S hee t
Embedded Algorithm Performance Table
Table 5.4 Embedded Algorithm Characteristics (-40°C to +85°C)
Parameter
Typ (Note 2)
Max (Note 3)
Unit
Sector Erase Time 128 kbyte
275
1100
ms
Single Word Programming Time (Note 1)
125
400
µs
2-byte (Note 1)
125
750
32-byte (Note 1)
160
750
64-byte (Note 1)
175
750
128-byte (Note 1)
198
750
256-byte (Note 1)
239
750
512-byte
340
750
512-byte
1.33
Buffer Programming Time
Effective Write Buffer Program
Operation per Word
Comments
Includes pre-programming prior
to erasure (Note 5)
µs
Sector Programming Time 128 kB (full Buffer
Programming)
108
µs
192
ms
Erase Suspend/Erase Resume (tESL)
40
µs
Program Suspend/Program Resume (tPSL)
40
µs
(Note 6)
Erase Resume to next Erase Suspend (tERS)
100
µs
Minimum of 60 ns but ≥ typical
periods are needed for Erase to
progress to completion.
Program Resume to next Program Suspend (tPRS)
100
µs
Minimum of 60 ns but ≥ typical
periods are needed for Program
to progress to completion.
Blank Check
6.2
NOP (Number of Program-operations, per Line)
8.5
ms
256
Notes:
1. Not 100% tested.
2. Typical program and erase times assume the following conditions: 25°C, 3.0V VCC, 10,000 cycle, and a random data pattern.
3. Under worst case conditions of 90°C, VCC = 2.70V, 100,000 cycles, and a random data pattern.
4. Effective write buffer specification is based upon a 512-byte write buffer operation.
5. In the pre-programming step of the Embedded Erase algorithm, all words are programmed to 0000h before Sector and Chip erasure.
6. System-level overhead is the time required to execute the bus-cycle sequence for the program command. See Table 6.1, Command
Definitions on page 57 for further information on command definitions.
46
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Table 5.5 Embedded Algorithm Characteristics (-40°C to +105°C)
Parameter
Sector Erase Time 128 kbyte
Single Word Programming Time (Note 1)
Typ (Note 2)
Max (Note 3)
Unit
275
1100
ms
µs
125
400
2-byte (Note 1)
150
1050
32-byte (Note 1)
200
1050
64-byte (Note 1)
220
1050
128-byte (Note 1)
250
1050
256-byte (Note 1)
320
1050
512-byte
420
1050
512-byte
1.64
Buffer Programming Time
Effective Write Buffer Program
Operation per Word
Comments
Includes pre-programming prior
to erasure (Note 5)
µs
Sector Programming Time 128 kB (full Buffer
Programming)
108
µs
269
ms
Erase Suspend/Erase Resume (tESL)
50
µs
Program Suspend/Program Resume (tPSL)
50
µs
(Note 6)
Erase Resume to next Erase Suspend (tERS)
100
µs
Minimum of 60 ns but ≥ typical
periods are needed for Erase to
progress to completion.
Program Resume to next Program Suspend (tPRS)
100
µs
Minimum of 60 ns but ≥ typical
periods are needed for Program
to progress to completion.
Blank Check
7.6
NOP (Number of Program-operations, per Line)
9.0
ms
1 per 16 word
Notes:
1. Not 100% tested.
2. Typical program and erase times assume the following conditions: 25°C, 3.0V VCC, 10,000 cycle, and a random data pattern.
3. Under worst case conditions of 105°C, VCC = 2.70V, 100,000 cycles, and a random data pattern.
4. Effective write buffer specification is based upon a 512-byte write buffer operation.
5. In the pre-programming step of the Embedded Erase algorithm, all words are programmed to 0000h before Sector and Chip erasure.
6. System-level overhead is the time required to execute the bus-cycle sequence for the program command. See Table 6.1, Command
Definitions on page 57 for further information on command definitions.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
47
D at a
5.6.1
S hee t
Command State Transitions
Table 5.6 Read Command State Transition
Current State
Command
and Condition
Read
Software
Reset / ASO
Exit
Status
Register Read
Enter
Status
Register Clear
Unlock 1
Blank Check
CFI Entry
Address
RA
xh
x555h
x555h
x555h
(SA)555h
(SA)55h
Data
RD
xF0h
x70h
x71h
xAAh
x33h
x98h
Read Protect =
False
READ
READ
READSR
(READ)
READ
READUL1
-
(return)
-
-
READ
READSR
-
-
CFI
BLCK
-
-
-
Table 5.7 Read Unlock Command State Transition
Current
State
READUL1
Read
Status
Register
Read
Enter
Unlock
2
Address
RA
x555h
x2AAh
x555h
Data
RD
x70h
x55h
xA0h
-
READU
L1
Command
and
Condition
READSR READU
(READ)
L2
Read
Protect =
True
Word
Write to
Program Buffer
Entry
Enter
Lock
Register
Entry
Password
ASO
Entry
PPB
Entry
PPB
Lock
Entry
DYB
ASO
Entry
x555h
x555h
x555h
x555h
x555h
x40h
x60h
xC0h
x50h
xE0h
-
-
-
-
-
-
-
-
-
-
PPBLB
DYB
Erase
Enter
ID (Autoselect)
Entry
(SA)xh
x555h
(SA)555h (SA)555h
x25h
x80h
x90h
x88h
-
-
-
-
-
-
-
SSR
Entry
READUL2
Read
Protect =
False
READU
L2
READSR
(READ)
-
CFI
PG1
Read
Protect =
False and
LR(8) = 0
WB
ER
PP
SSR
LR
PPB
Table 5.8 Erase State Command Transition
Current
State
Command
and
Condition
Read
Software
Reset / ASO
Exit
Status
Register
Read Enter
Status
Register
Clear
Unlock 1
Unlock 2
Chip Erase
Start
Sector
Erase Start
Erase
Suspend
Enhanced
Method (2)
Address
RA
xh
x555h
x555h
x555h
x2AAh
x555h
(SA)xh
xh
Data
RD
xF0h
x70h
x71h
xAAh
x55h
x10h
x30h
xB0h
-
ERUL1
-
-
-
-
ER
-
ER
-
READSR
(READ)
ERUL1
-
ERUL1
-
READSR
(READ)
-
-
ERUL2
-
-
-
ERUL2
-
ERUL2
-
READSR
(READ)
-
-
-
CER
SER
-
CER (1)
-
CER
-
ERSR
(CER)
-
-
-
-
-
-
-
-
-
-
ESR (ES)
-
-
-
-
-
SR(7) = 0
SER (1)
SER
SR(7) = 1
READ
SR(7) = 0
BLCK (1)
BLCK
SR(7) = 1
ERSR
-
READ
ERSR
(SER)
ERSR
(BLCK)
READ
READ
(return)
Notes:
1. State will automatically move to READ state at the completion of the operation.
2. Also known as Erase Suspend/Program Suspend Legacy Method.
48
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Table 5.9 Erase Suspend State Command Transition
Current State
Command and
Condition
Read
Software Reset /
ASO Exit
Status Register
Read Enter
Status Register
Clear
Unlock 1
Sector Erase
Start
Address
RA
xh
x555h
x555h
x555h
(SA)xh
Data
RD
xF0h
x70h
x71h
xAAh
x30h
-
ESR
ERSR (ESR)
-
-
ESR (1)
-
SR(7) = 0
-
ES
ES
ES
ESSR (ES)
ES
ESUL1
SR(7) = 1
ESSR
SER
-
(return)
-
-
-
-
-
Note:
1. State will automatically move to ES state by tESL.
Table 5.10 Erase Suspend Unlock State Command Transition
Current
State
Status
Software Register
Reset /
Read
ASO Exit
Enter
WritetoBufferAbort
Reset
Start
Erase
Resume
Enhanced
Method
(1)
DYB
ASO
Entry
(SA)xh
x555h
xh
x555h
NOT
x555h
xh
NOT
x2AAh
xh
xA0h
x25h
xF0h
x30h
xE0h
xh
NOT
xF0h
xh
NOT
x55h
-
-
-
-
-
-
-
-
ESPG
ESPG
-
-
Command
and
Condition
Read
Address
RA
xh
x555h
x2AAh
x555h
Data
RD
xF0h
x70h
x55h
ESUL1
-
ESSR
(ES)
ESUL2
Unlock
1
Word
Write to
Program Buffer
Entry
Enter
NOT a valid “Write-to-BufferAbort Reset” Command
ESUL1
SR(3) = 1
DQ(1) = 1
-
ESUL2
-
Read
Protect =
False
-
ES
-
-
ESDYB
ESSR
(ES)
ESUL2
-
ESPG1
ES_WB
SER
SR(3) = 1
-
ES
-
ESPG
ESPG
DQ(1) = 1
Note:
1. Also known as Erase Resume/Program Resume Legacy Method.
Table 5.11 Erase Suspend - DYB State Command Transition
Current State
Command and
Condition
Read
Software
Reset / ASO
Exit
Status
Register
Read Enter
Status
Register
Clear
Command
Set Exit
Entry
Command
Set Exit
DYB Set/
Clear Entry
Password
Word Count
Address
RA
xh
x555h
x555h
xh
xh
xh
xh
Data
RD
xF0h
x70h
x71h
x90h
x00h
xA0h
x03h
ESDYB
ESDYBEXT
-
ESDYBSET
-
ESDYB
-
ESDYB
ES
ESSR
(ESDYB)
ESDYBSET
-
ESDYBSET
-
-
-
-
-
-
-
ESDYBEXT
-
ESDYBEXT
-
-
-
-
ES
-
ES
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
49
D at a
S hee t
Table 5.12 Erase Suspend - Program Command State Transition
Current State
ES_WB
Command
and Condition
Read
Software
Reset / ASO
Exit
Status
Register Read
Enter
Status
Register Clear
Unlock 1
Program
Erase
Suspend
Suspend
Enhanced Enhanced
Method
Method (1)
Address
RA
xh
x555h
x555h
x555h
xh
xh
xh
Data
RD
xF0h
x70h
x71h
xAAh
xB0h
x51h
xh
ES_WB
-
-
-
-
-
-
WC > 256 or
SA ≠ SA
WC ≤ 256 and
SA = SA
ESPG
ES_WB_
D
WC < 0 or
Write Buffer ≠
Write Buffer
ES_WB_D
ESPG
ES_WB_D
-
-
-
-
-
-
WC > 0 and
Write Buffer =
Write Buffer
ESPG1
-
ES_WB_
D
ESPG1
SR(7) = 0
ESPG
-
-
-
ES
ESPGSR
(ESPG)
-
-
-
ESPG
SR(7) = 1
ESPGSR
Write
Data
-
(return)
-
-
-
ESPG
-
ESUL1
ESPSR
(ESPG)
ESPSR
(ESPG)
ESPG
ES
-
-
-
(return)
Note:
1. Also known as Erase Suspend/Program Suspend Legacy Method.
Table 5.13 Erase Suspend - Program Suspend Command State Transistion
Current State
Command
and Condition
Read
Software
Reset / ASO
Exit
Status
Register Read
Enter
Status
Register Clear
Unlock 1
Unlock 2
Erase
Resume
Enhanced
Method
(2)
Program
Resume
Enhanced
Method
Address
RA
xh
x555h
x555h
x555h
x2AAh
xh
xh
Data
RD
xF0h
x70h
x71h
xAAh
x55h
x30h
x50h
ESPSR (1)
-
ESPSR
-
ESPGSR
(ESPSR)
-
-
-
-
-
ESPS
-
ESPS
ESPS
ESPSSR
(ESSP)
ESPS
ESPSUL1
-
ESPG
ESPG
ESPSSR
-
(return)
-
-
-
-
-
-
-
-
-
ESPSUL2
-
-
-
-
-
ESPG
ESPG
ESPSUL1
-
ESPSUL1
-
ESPSSR
(ESPS)
ESPSUL2
-
ESPSUL2
-
ESPSSR
(ESPS)
Notes:
1. State will automatically move to ESPS state by tPSL.
2. Also known as Erase Resume/Program Resume Legacy Method.
50
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Table 5.14 Program State Command Transition
Current
State
Command
and
Condition
Read
Status
Register
Read Enter
Status
Register
Clear
Unlock 1
Program
Buffer to
flash
(confirm)
Erase
Suspend
Enhanced
Method (2)
Program
Suspend
Enhanced
Method
Write
Data
Address
RA
xh
x555h
x555h
x555h
(SA)xh
xh
xh
xh
Data
RD
xF0h
x70h
x71h
xAAh
x29h
xB0h
x51h
xh
WB
-
-
-
-
-
-
-
WC > 256 or
SA ≠ SA
WB
Software
Reset / ASO
Exit
PG
WC ≤ 256
and SA = SA
WB_D
Write Buffer ≠
Write Buffer
PG
WC = 0
WB_D
WB_D
-
-
-
-
-
-
PBF
-
WC > 0 and
Write Buffer =
Write Buffer
WB_D
PBF
-
-
-
-
-
-
PG
-
-
PG
PG1
-
PG1
-
-
-
-
-
-
-
PG
-
-
PSR (PG)
PSR (PG)
READ
WBUL1
-
-
SR(7) = 0
PG (1)
-
SR(7) = 1
PG
PGSR (PG)
-
READ
SR(7) = 1 and
SR(1) = 0
PG
Notes:
1. State will automatically move to READ state at the completion of the operation.
2. Also known as Erase Suspend/Program Suspend Legacy Method.
Table 5.15 Program Unlock State Command Transition
Current State
Command
and
Condition
Read
Software
Reset / ASO
Exit
Status
Register
Read Enter
Unlock 2
NOT a valid “Write-to-Buffer-Abort Reset” Command
Address
RA
xh
x555h
x2AAh
NOT x555h
xh
NOT x2AAh
xh
Data
RD
xF0h
x70h
x55h
xh
NOT xF0h
xh
NOT x55h
-
-
WBUL1
-
-
WBUL2
-
PG
PG
-
-
-
-
WBUL1
SR(3) = 1
DQ(1) = 1
-
WBUL2
SR(3) = 1
WBUL2
READ
-
-
-
PG
PG
-
-
-
DQ(1) = 1
PGSR
-
(return)
-
-
-
Table 5.16 Program Suspend State Command Transition
Current State
Command and
Condition
Read
Status Register
Read Enter
Status Register
Clear
Erase Resume
Enhanced Method (2)
Program Resume
Enhanced Method
Address
RA
x555h
x555h
xh
xh
Data
RD
x70h
x71h
x30h
x50h
PSR (1)
-
PSR
PGSR (PSR)
-
-
-
PS
-
PS
PSSR (PS)
PS
PG
PG
PSSR
-
(return)
-
-
-
-
Notes:
1. State will automatically move to PS state by tPSL.
2. Also known as Erase Resume/Program Resume Legacy Method.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
51
D at a
S hee t
Table 5.17 Lock Register State Command Transition
Command
and
Condition
Current State
Read
Software
Reset / ASO
Exit
Status
Register
Read Enter
Status
Register
Clear
Command
Set Exit
Entry
Command
Set Exit
PPB Lock
Bit Set Entry
Password
Word Count
Address
RA
xh
x555h
x555h
xh
xh
xh
Xh
Data
RD
xF0h
x70h
x71h
x90h
x00h
xA0h
x03h
LR
-
LR
READ
LRSR (LR)
LR
LREXT
-
LRPG1
-
LRPG1
-
LRPG1
-
-
-
-
-
-
-
-
-
-
-
-
LRPG
-
LRPG
-
LRSR
(LRPG)
LRSR
-
(return)
-
-
-
-
-
-
-
LREXT
-
LREXT
-
-
-
-
READ
-
READ
Table 5.18 CFI State Command Transition
Command and
Condition
Current State
Read
Software Reset / ASO
Exit
Status Register Read
Enter
Status Register Clear
Address
RA
xh
x555h
x555h
Data
RD
xF0h
x70h
x71h
CFI
-
CFI
READ
CFISR (CFI)
CFI
CFISR
-
(return)
-
-
-
Table 5.19 Secure Silicon Sector State Command Transition
Current State
Command and
Condition
Read
Software Reset /
ASO Exit
Status Register
Read Enter
Status Register
Clear
Unlock 1
Address
RA
xh
x555h
x555h
x555h
Data
RD
xF0h
x70h
x71h
xAAh
-
SSR
READ
SSRSR (SSR)
SSR
SSRUL1
SSR
Table 5.20 Secure Silicon Sector Unlock State Command Transition
Current
State
Command
and
Condition
Read
Software
Reset /
ASO Exit
Status
Register
Read
Enter
Unlock 2
Word
Program
Entry
Write to
Buffer
Enter
Comman
d Set Exit
Entry
Address
RA
xh
x555h
x2AAh
x555h
(SA)xh
x555h
NOT
x555h
xh
NOT
x2AAh
xh
Data
RD
xF0h
x70h
x55h
xA0h
x25h
x90h
xh
NOT xF0h
xh
NOT x55h
-
-
SSRPG
SSRPG
-
-
NOT a valid “Write-to-Buffer-Abort Reset”
Command
SSRUL1
DQ(1) = 1
SSRUL1
READ
SSRSR
(SSR)
SSRUL2
-
-
-
-
-
-
-
SR(3) = 1
SSRUL2
DQ(1) = 1
SSRUL2
SSR
SSRPG1
SSR_WB
-
-
SSRPG
SSRPG
SSREXT
SR(3) = 1
52
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Table 5.21 Secure Silicon Sector Program State Command Transition
Current State
Command and
Condition
Read
Software Reset /
ASO Exit
Status Register
Read Enter
Status Register
Clear
Unlock 1
Command Set
Exit
Address
RA
xh
x555h
x555h
x555h
xh
Data
RD
xF0h
x70h
x71h
xAAh
x00h
-
SSRPG1
-
-
SSRPG1
-
-
SSR_WB
-
-
-
-
-
SSR_WB_D
-
-
-
-
-
SSRPG1
WC > 256 or SA
≠ SA
SSR_WB
WC ≤ 256 and
SA = SA
WC < 0 or Write
Buffer ≠ Write
Buffer
SSR_WB_D
WC > 0 and
Write Buffer =
Write Buffer
SR(7) = 0
-
SR(7) = 1
-
SR(7) = 1 and
DQ(1) = 0
SSRPG
SSRPG
SSR
SSRSR
(SSRPG)
READ
-
DQ(1) = 1
-
-
SSRUL1
SR(3) = 1
SSRSR
-
(return)
-
-
-
-
-
SSREXT
-
SSREXT
-
SSRSR (SSR)
-
-
READ
Table 5.22 Password Protection Command State Transition
Current
State
Command
and
Condition
Read
Software
Reset /
ASO Exit
Status
Register
Read
Enter
Status
Register
Clear
Password
ASO
Unlock
Enter
Password
ASO
Unlock
Start
Command
Set Exit
Entry
Command
Set Exit
Program
Entry
Password
Word
Count
Address
RA
xh
x555h
x555h
0h
0h
xh
xh
xh
Xh
Data
RD
xF0h
x70h
x71h
x25h
x29h
x90h
x00h
xA0h
x03h
PP
-
PP
READ
PPSR (PP)
PP
PPWB25
-
PPEXT
-
PPPG1
-
PPWB25
-
PPWB25
-
-
-
-
-
-
-
-
PPD
-
-
-
-
-
-
-
-
PPD
PPPG1
WC > 0
PPD
WC ≤ 0
-
-
PPPG1
PPPG
-
-
-
-
-
-
-
-
-
-
PPSR
(PPPG)
-
-
-
-
-
-
-
PPPG
-
PPPG
PPSR
-
(return)
-
-
-
-
-
-
-
-
-
PPEXT
-
PPEXT
-
-
-
-
-
-
READ
-
-
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
53
D at a
S hee t
Table 5.23 Non-Volatile Protection Command State Transition
Current
State
Command
and
Condition
PPB
PPBPG1
Read
Software
Reset /
ASO Exit
Status
Register
Read
Enter
Status
Register
Clear
Command
Set Exit
Entry
Command
Set Exit
Program
Entry
DYB Set
Start
All PPB
Erase
Enter
All PPB
Erase
Start
Address
RA
xh
x555h
x555h
xh
xh
xh
(SA)xh
Xh
0h
Data
RD
xF0h
x70h
x71h
x90h
x00h
xA0h
x00h
x80h
x30h
-
PPB
READ
PPBSR
(PPB)
PPB
PPBEXT
-
PPBPG1
-
PPBPG1
-
-
PPBPG1
READ
-
-
-
PPBPG
-
PPB
-
PPBER
PPBSR
(PPBPG)
-
-
-
-
-
-
-
-
-
-
-
-
SR(7) = 0
-
PPBPG
PPBPG
SR(7) = 1
READ
SR(7) = 0
-
PPBER
-
READ
PPBSR
(PPBER)
READ
PPBER
SR(7) = 1
READ
PPBSR
-
(return)
-
-
-
-
-
-
-
-
-
PPBEXT
-
PPBEXT
-
-
-
-
READ
-
-
-
-
Table 5.24 PPB Lock Bit Command State Transition
Current State
Command
and Condition
Read
Software
Reset / ASO
Exit
Status
Register Read
Enter
Status
Register Clear
Command Set
Exit Entry
Command Set
Exit
Program Entry
Address
RA
xh
x555h
x555h
xh
xh
xh
Data
RD
xF0h
x70h
x71h
x90h
x00h
xA0h
PPBLB
PPBLBEXT
-
PPBLBSET
PPBLB
-
PPBLB
READ
PPBLBSR
(PPBLB)
PPBLBSR
-
(return)
-
-
-
-
-
-
PPBLBSET
LR(2) = 0 and
LR(5) = 0
PPBLBSET
-
-
-
-
PPBLB
-
PPBLBEXT
-
PPBLBEXT
-
-
-
-
READ
-
Table 5.25 Volatile Sector Protection Command State Transition
Current
State
DYB
54
Command
and
Condition
Read
Software
Reset / ASO
Exit
Status
Register
Read Enter
Status
Register
Clear
Command
Set Exit
Entry
Command
Set Exit
Program
Entry
DYB Set
Start
DYB Clear
Start
Address
RA
xh
x555h
x555h
xh
xh
xh
(SA)xh
(SA)xh
Data
RD
xF0h
x70h
x71h
x90h
x00h
xA0h
x00h
x01h
-
DYB
READ
DYBSR
(DYB)
DYB
DTBEXT
-
DYBSET
-
-
DYBSR
-
(return)
-
-
-
-
-
-
-
-
DYBSET
-
DYBSET
-
-
-
-
-
-
DYB
DYB
DYBEXT
-
DYBEXT
-
-
-
-
READ
-
-
-
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Table 5.26 State Transition Definitions (Sheet 1 of 2)
Current State
Command Transition
Definition
BLCK
Table 5.8
Blank Check
CER
Table 5.8
Chip Erase Start
CFI
Table 5.18
ID (Autoselect)
CFISR
Table 5.18
ID (Autoselect) - Status Register Read
DYB
Table 5.25
DYB ASO
DYBEXT
Table 5.25
DYB ASO - Command Exit
DYBSET
Table 5.25
DYB ASO - Set
DYBSR
Table 5.25
DYB ASO - Status Register Read
ER
Table 5.8
Erase Enter
ERSR
Table 5.8
Erase - Status Register Read
ERUL1
Table 5.8
Erase - Unlock Cycle 1
ERUL2
Table 5.8
Erase - Unlock Cycle 2
ES
Table 5.9
Erase Suspended
ESDYB
Table 5.11
Erase Suspended - DYB ASO
ESDYBEXT
Table 5.11
Erase Suspended - DYB Command Exit
ESDYBSET
Table 5.11
Erase Suspended - DYB Set/Clear
ESPG
Table 5.12
Erase Suspended - Program
ESPGSR
Table 5.12
Erase Suspended - Program - Status Register Read
ESPG1
Table 5.12
Erase Suspended - Word Program
ESPS
Table 5.13
Erase Suspended - Program Suspended
ESPSR
Table 5.13
Erase Suspended - Program Suspend
ESPSSR
Table 5.13
Erase Suspended - Program Suspend - Status Register Read
ESPSUL1
Table 5.13
Erase Suspended - Program Suspend - Unlock 1
ESPSUL2
Table 5.13
Erase Suspended - Program Suspend - Unlock 2
ESR
Table 5.9
Erase Suspend Request
ESSR
Table 5.9
Erase Suspended - Status Register Read
ESUL1
Table 5.10
Erase Suspended - Unlock Cycle 1
ESUL2
Table 5.10
Erase Suspended - Unlock Cycle 2
ES_WB
Table 5.12
Erase Suspended - Write to Buffer
ES_WB_D
Table 5.12
Erase Suspended - Write to Buffer Data
LR
Table 5.17
Lock Register
LREXT
Table 5.17
Lock Register - Command Exit
LRPG
Table 5.17
Lock Register - Program
LRPG1
Table 5.17
Lock Register - Program Start
LRSR
Table 5.17
Lock Register - Status Register Read
PBF
Table 5.14
Page Buffer Full
PG
Table 5.14
Program
PGSR
Table 5.15
Program - Status Register Read
PG1
Table 5.14
Word Program
PP
Table 5.22
Password ASO
PPB
Table 5.23
PPB
PPBER
Table 5.23
PPB - Erase
PPBEXT
Table 5.23
PPB - Command Exit
PPBLB
Table 5.24
PPB Lock Bit
PPBLBEXT
Table 5.24
PPB Lock Bit - Command Exit
PPBLBSET
Table 5.24
PPB Lock Bit - Set
PPBLBSR
Table 5.24
PPB Lock Bit - Status Register Read
PPBPG
Table 5.23
PPB - Program
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
55
D at a
S hee t
Table 5.26 State Transition Definitions (Sheet 2 of 2)
Current State
56
Command Transition
Definition
PPBPG1
Table 5.23
PPB - Program Request
PPBSR
Table 5.23
PPB - Status Register Read
PPD
Table 5.22
Password ASO - Data
PPEXT
Table 5.22
Password ASO - Command Exit
PPPG
Table 5.22
Password ASO - Program
PPPG1
Table 5.22
Password ASO - Program Request
PPSR
Table 5.22
Password ASO - Status Register Read
PS
Table 5.16
Program Suspended
PSR
Table 5.16
Program Suspend Request
PSSR
Table 5.16
Program Suspended - Status Register Read
PPWB25
Table 5.22
Password ASO - Unlock
READ
Table 5.6
Read Array
READSR
Table 5.6
Read Status Register
READUL1
Table 5.7
Read - Unlock Cycle 1
READUL2
Table 5.7
Read - Unlock Cycle 2
SER
Table 5.8
Sector Erase Start
SSR
Table 5.19
Secure Silicon
SSREXT
Table 5.21
Secure Silicon - Command Exit
SSRPG
Table 5.21
Secure Silicon - Program
SSRPG1
Table 5.21
Secure Silicon - Word Program
SSRSR
Table 5.21
Secure Silicon - Status Register Read
SSRUL1
Table 5.20
Secure Silicon - Unlock Cycle 1
SSRUL2
Table 5.20
Secure Silicon - Unlock Cycle 2
SSR_WB
Table 5.21
Secure Silicon - Write to Buffer
SSR_WB_D
Table 5.21
Secure Silicon - Write to Buffer - Write Data
WB
Table 5.14
Write to Buffer
WBUL1
Table 5.15
Write Buffer - Unlock Cycle 1
WBUL2
Table 5.15
Write Buffer - Unlock Cycle 2
WB_D
Table 5.14
Write to Buffer Write Data
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
6.
She et
Software Interface Reference
6.1
Command Summary
Command Sequence
(Note 1)
Cycles
Table 6.1 Command Definitions (Sheet 1 of 3)
Bus Cycles (Notes 2-5)
First
Second
Addr
Data
1
RA
RD
Reset/ASO Exit (Notes 7, 16)
1
XXX
F0
Data
XXX
RD
Third
Fourth
Addr
Data
Addr
Fifth
Data
Sixth
Seventh
Addr
Data
Addr
Data
Status Register Read
2
555
70
Status Register Clear
1
555
71
Word Program
4
555
AA
2AA
55
555
A0
PA
PD
Write to Buffer
6
555
AA
2AA
55
SA
25
SA
WC
WBL
PD
WBL
PD
Program Buffer to Flash
(confirm)
1
SA
29
Write-to-Buffer-Abort Reset
(Note 11)
3
555
AA
2AA
55
555
F0
Chip Erase
6
555
AA
2AA
55
555
80
555
AA
2AA
55
555
10
Sector Erase
6
555
AA
2AA
55
555
80
555
AA
2AA
55
SA
30
Erase Suspend/Program
Suspend
Legacy Method (Note 9)
1
XXX
B0
1
XXX
30
Program Suspend Enhanced
Method
1
XXX
51
Program Resume Enhanced
Method
1
XXX
50
Blank Check
1
(SA)
555
33
ID-CFI (Autoselect) ASO
Read (Note 6)
Addr
ID (Autoselect) Entry
3
555
AA
2AA
55
(SA)
555
90
CFI Enter (Note 8)
1
(SA)
55
98
ID-CFI Read
1
RA
RD
Reset/ASO Exit
(Notes 7, 16)
1
XXX
F0
WBL
PD
WBL
PD
Addr
Data
Erase Suspend Enhanced
Method
Erase Resume/Program
Resume
Legacy Method (Note 10)
Erase Resume Enhanced
Method
Secure Silicon Region (SSR) ASO
Secure Silicon Region Command Definitions
2AA
55
(SA)
555
88
AA
2AA
55
555
A0
PA
PD
555
AA
2AA
55
SA
25
SA
WC
1
SA
29
Write-to-Buffer-Abort
Reset (Note 11)
3
555
AA
2AA
55
555
F0
SSR Exit (Note 11)
4
555
AA
2AA
55
555
90
XX
0
Reset/ASO Exit
(Notes 7, 16)
1
XXX
F0
SSR Entry
3
555
AA
Read (Note 6)
Word Program
1
RA
RD
4
555
Write to Buffer
6
Program Buffer to Flash
(confirm)
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
57
D at a
S hee t
Command Sequence
(Note 1)
Cycles
Table 6.1 Command Definitions (Sheet 2 of 3)
Bus Cycles (Notes 2-5)
First
Addr
Second
Data
Addr
Data
Third
Addr
Fourth
Data
Addr
Data
Fifth
Sixth
Seventh
Addr
Data
Addr
Data
Addr
Data
2
PWD2
3
PWD
3
0
29
Lock Register Command Set Definitions
Lock Register ASO
Lock Register Entry
3
555
AA
2AA
55
Program (Note 15)
2
Read (Note 15)
1
XXX
A0
XXX
PD
0
RD
Command Set Exit
(Notes 12, 16)
2
XXX
90
XXX
0
Reset/ASO Exit
(Notes 7, 16)
1
XXX
F0
555
40
Password Protection Command Set Definitions
Password ASO
Password ASO Entry
3
555
AA
2AA
55
PWDx
555
60
Program (Note 14)
2
XXX
A0
PWA
x
Read (Note 13)
4
0
PWD0
1
PWD1
2
PWD2
3
PWD
3
Unlock
7
0
25
0
3
0
PWD0
1
PWD
1
Command Set Exit
(Notes 12, 16)
2
XXX
90
XXX
0
Reset/ASO Exit
(Notes 7, 16)
1
XXX
F0
PPB Entry
3
555
AA
2AA
PPB Program (Note 17)
2
XXX
A0
SA
0
All PPB Erase (Note 17)
2
XXX
80
0
30
PPB Read (Note 17)
1
SA
RD (0)
Command Set Exit
(Notes 12, 16)
2
XXX
90
XXX
0
Reset/ASO Exit
(Notes 7, 16)
1
XXX
F0
PPB (Non-Volatile Sector Protection)
Non-Volatile Sector Protection Command Set Definitions
55
555
C0
PPB Lock Bit
Global Non-Volatile Sector Protection Freeze Command Set Definitions
58
PPB Lock Entry
3
555
AA
2AA
55
PPB Lock Bit Cleared
2
XXX
A0
XXX
0
PPB Lock Status Read
(Note 17)
1
XXX
RD (0)
Command Set Exit
(Notes 12, 16)
2
XXX
90
XXX
0
Reset/ASO Exit (Note 16)
1
XXX
F0
555
50
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Command Sequence
(Note 1)
Cycles
Table 6.1 Command Definitions (Sheet 3 of 3)
Bus Cycles (Notes 2-5)
First
Addr
Second
Data
Addr
Data
Third
Addr
Fourth
Data
Addr
Data
Fifth
Addr
Data
Sixth
Addr
Data
Seventh
Addr
Data
DYB (Volatile Sector Protection) ASO
Volatile Sector Protection Command Set Definitions
DYB ASO Entry
3
555
AA
2AA
55
DYB Set (Note 17)
2
XXX
A0
SA
0
DYB Clear (Note 17)
2
XXX
A0
SA
1
DYB Status Read
(Note 17)
1
SA
RD (0)
Command Set Exit
(Notes 12, 16)
2
XXX
90
XXX
0
Reset/ASO Exit (Note 16)
1
XXX
F0
555
E0
Legend:
X = Don't care.
RA = Address of the memory to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed.
PD = Data to be programmed at location PA.
SA = Address of the sector selected. Address bits AMAX-A16 uniquely select any sector.
WBL = Write Buffer Location. The address must be within the same Line.
WC = Word Count is the number of write buffer locations to load minus 1.
PWAx = Password address for word0 = 00h, word1 = 01h, word2 = 02h, and word3 = 03h.
PWDx = Password data word0, word1, word2, and word3.
Notes:
1. See Table 8.1, Interface States on page 67 for description of bus operations.
2. All values are in hexadecimal.
3. Except for the following, all bus cycles are write cycle: read cycle during Read, ID/CFI Read (Manufacturing ID / Device ID), Indicator Bits,
Secure Silicon Region Read, SSR Lock Read, and 2nd cycle of Status Register Read .
4. Data bits DQ15-DQ8 are don't care in command sequences, except for RD, PD, WC and PWD.
5. Address bits AMAX-A11 are don't cares for unlock and command cycles, unless SA or PA required. (AMAX is the Highest Address pin.).
6. No unlock or command cycles required when reading array data.
7. The Reset command is required to return to reading array data when device is in the ID-CFI (autoselect) mode, or if DQ5 goes High
(while the device is providing status data).
8. Command is valid when device is ready to read array data or when device is in ID-CFI (autoselect) mode.
9. The system can read and program/program suspend in non-erasing sectors, or enter the ID-CFI ASO, when in the Erase Suspend mode.
The Erase Suspend command is valid only during a sector erase operation.
10. The Erase Resume/Program Resume command is valid only during the Erase Suspend/Program Suspend modes.
11. Issue this command sequence to return to READ mode after detecting device is in a Write-to-Buffer-Abort state. IMPORTANT: the full
command sequence is required if resetting out of ABORT.
12. The Exit command returns the device to reading the array.
13. The password portion can be entered or read in any order as long as the entire 64-bit password is entered or read.
14. For PWDx, only one portion of the password can be programmed per each A0 command. Portions of the password must be programmed
in sequential order (PWD0 - PWD3).
15. All Lock Register bits are one-time programmable. The program state = 0 and the erase state = 1. Also, both the Persistent Protection
Mode Lock Bit and the Password Protection Mode Lock Bit cannot be programmed at the same time or the Lock Register Bits Program
operation aborts and returns the device to read mode. Lock Register bits that are reserved for future use are undefined and may be 0’s or
1's.
16. If any of the Entry commands was issued, an Exit command must be issued to reset the device into read mode.
17. Protected State = 00h, Unprotected State = 01h. The sector address for DYB set, DYB clear, or PPB Program command may be any
location within the sector - the lower order bits of the sector address are don't care.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
59
D at a
6.2
S hee t
Device ID and Common Flash Interface (ID-CFI) ASO Map
The Device ID portion of the ASO (word locations 0h to 0Fh) provides manufacturer ID, device ID, Sector
Protection State, and basic feature set information for the device.
ID-CFI Location 02h displays sector protection status for the sector selected by the sector address (SA) used
in the ID-CFI enter command. To read the protection status of more than one sector it is necessary to exit the
ID ASO and enter the ID ASO using the new SA. The access time to read location 02h is always tACC and a
read of this location requires CE# to go High before the read and return Low to initiate the read
(asynchronous read access). Page mode read between location 02h and other ID locations is not supported.
Page mode read between ID locations other than 02h is supported.
For additional information see ID-CFI ASO on page 35.
Table 6.2 ID (Autoselect) Address Map
Description
Address
Manufacture ID
(SA) + 0000h
Device ID
(SA) + 0001h
227Eh
(SA) + 0002h
Sector Protection State (1= Sector protected, 0= Sector unprotected). This protection state
is shown only for the SA selected when entering ID-CFI ASO. Reading other SA provides
undefined data. To read a different SA protection state ASO exit command must be used
and then enter ID-CFI ASO again with the new SA.
Protection
Verification
Read Data
0001h
DQ15-DQ08 = 1 (Reserved)
DQ7 - Factory Locked Secure Silicon Region
1 = Locked,
0 = Not Locked
DQ6 - Customer Locked Secure Silicon Region
1 = Locked
Indicator Bits
(SA) + 0003h
0 = Not Locked
DQ5 = 1 (Reserved)
DQ4 - WP# Protects
0 = lowest address Sector
1 = highest address Sector
DQ3 - DQ0 = 1 (Reserved)
(SA) + 0004h
Reserved
(SA) + 0005h
Reserved
(SA) + 0006h
Reserved
(SA) + 0007h
Reserved
(SA) + 0008h
Reserved
RFU
(SA) + 0009h
Reserved
(SA) + 000Ah
Reserved
(SA) + 000Bh
Reserved
Bit 0 - Status Register Support
1 = Status Register Supported
0 = Status Register not supported
Bit 1 - DQ polling Support
1 = DQ bits polling supported
Lower Software Bits
(SA) + 000Ch
0 = DQ bits polling not supported
Bit 3-2 - Command Set Support
11 = reserved
10 = reserved
01 = Reduced Command Set
00 = Classic Command set
Bits 4-15 - Reserved = 0
60
Upper Software Bits
(SA) + 000Dh
Reserved
Device ID
(SA) + 000Eh
2228h = 1 Gb
2223h = 512 Mb
2222h = 256 Mb
2221h = 128 Mb
Device ID
(SA) + 000Fh
2201h
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Table 6.3 CFI Query Identification String
Word Address
Data
(SA) + 0010h
0051h
(SA) + 0011h
0052h
(SA) + 0012h
0059h
(SA) + 0013h
0002h
(SA) + 0014h
0000h
(SA) + 0015h
0040h
(SA) + 0016h
0000h
(SA) + 0017h
0000h
(SA) + 0018h
0000h
(SA) + 0019h
0000h
(SA) + 001Ah
0000h
Description
Query Unique ASCII string “QRY”
Primary OEM Command Set
Address for Primary Extended Table
Alternate OEM Command Set
(00h = none exists)
Address for Alternate OEM Extended Table
(00h = none exists)
Table 6.4 CFI System Interface String
Word Address
Data
(SA) + 001Bh
0027h
VCC Min. (erase/program) (D7-D4: volts, D3-D0: 100 mV)
Description
(SA) + 001Ch
0036h
VCC Max. (erase/program) (D7-D4: volts, D3-D0: 100 mV)
(SA) + 001Dh
0000h
VPP Min. voltage (00h = no VPP pin present)
(SA) + 001Eh
0000h
VPP Max. voltage (00h = no VPP pin present)
(SA) + 001Fh
0008h
Typical timeout per single word write 2N µs
(SA) + 0020h
0009h
Typical timeout for max
multi-byte program, 2N µs
(00h = not supported)
(SA) + 0021h
0008h
Typical timeout per individual block erase 2N ms
0012h (1 Gb)
(SA) + 0022h
0011h (512 Mb)
0010h (256 Mb)
Typical timeout for full chip erase 2N ms (00h = not supported)
000Fh (128 Mb)
(SA) + 0023h
0001h
Max. timeout for single word write 2N times typical
(SA) + 0024h
0002h
Max. timeout for buffer write 2N times typical
(SA) + 0025h
0003h
Max. timeout per individual block erase 2N times typical
(SA) + 0026h
0003h
Max. timeout for full chip erase 2N times typical
(00h = not supported)
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
61
D at a
S hee t
Table 6.5 CFI Device Geometry Definition
Word Address
Data
Description
001Bh (1 Gb)
(SA) + 0027h
001Ah (512 Mb)
0019h (256 Mb)
Device Size = 2N byte;
0018h (128 Mb)
(SA) + 0028h
0001h
(SA) + 0029h
0000h
Flash Device Interface Description 0 = x8-only, 1 = x16-only, 2 = x8/x16 capable
(SA) + 002Ah
0009h
(SA) + 002Bh
0000h
(SA) + 002Ch
0001h
(SA) + 002Dh
00XXh
(SA) + 002Eh
000Xh
(SA) + 002Fh
0000h
(SA) + 0030h
000Xh
(SA) + 0031h
0000h
(SA) + 0032h
0000h
(SA) + 0033h
0000h
(SA) + 0034h
0000h
(SA) + 0035h
0000h
(SA) + 0036h
0000h
(SA) + 0037h
0000h
(SA) + 0038h
0000h
Max. number of byte in multi-byte write = 2N
(00 = not supported)
Number of Erase Block Regions within device
1 = Uniform Device, 2 = Boot Device
Erase Block Region 1 Information (refer to JEDEC JESD68-01 or JEP137 specifications)
00FFh, 0003h, 0000h, 0002h =1 Gb
00FFh, 0001h, 0000h, 0002h = 512 Mb
00FFh, 0000h, 0000h, 0002h = 256 Mb
007Fh, 0000h, 0000h, 0002h = 128 Mb
Erase Block Region 2 Information (refer to CFI publication 100)
Erase Block Region 3 Information (refer to CFI publication 100)
(SA) + 0039h
0000h
(SA) + 003Ah
0000h
(SA) + 003Bh
0000h
Erase Block Region 4 Information (refer to CFI publication 100)
62
(SA) + 003Ch
0000h
(SA) + 003Dh
FFFFh
Reserved
(SA) + 003Eh
FFFFh
Reserved
(SA) + 003Fh
FFFFh
Reserved
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Table 6.6 CFI Primary Vendor-Specific Extended Query (Sheet 1 of 2)
Word Address
Data
(SA) + 0040h
0050h
(SA) + 0041h
0052h
(SA) + 0042h
0049h
(SA) + 0043h
0031h
(SA) + 0044h
0035h
Description
Query-unique ASCII string “PRI”
Major version number, ASCII
Minor version number, ASCII
Address Sensitive Unlock (Bits 1-0)
00b = Required
01b = Not Required
Process Technology (Bits 5-2)
0000b = 0.23 µm Floating Gate
0001b = 0.17 µm Floating Gate
(SA) + 0045h
001Ch
0010b = 0.23 µm MirrorBit
0011b = 0.13 µm Floating Gate
0100b = 0.11 µm MirrorBit
0101b = 0.09 µm MirrorBit
0110b = 0.09 µm Floating Gate
0111b = 0.065 µm MirrorBit Eclipse
1000b = 0.065 µm MirrorBit
1001b = 0.045 µm MirrorBit
(SA) + 0046h
0002h
Erase Suspend
0 = Not Supported
1 = Read Only
2 = Read and Write
(SA) + 0047h
0001h
Sector Protect
00 = Not Supported
0000h
Temporary Sector Unprotect
00 = Not Supported
X = Number of sectors in smallest group
(SA) + 0048h
01 = Supported
(SA) + 0049h
0008h
Sector Protect/Unprotect Scheme
04 = High Voltage Method
05 = Software Command Locking Method
08 = Advanced Sector Protection Method
(SA) + 004Ah
0000h
Simultaneous Operation
00 = Not Supported
0000h
Burst Mode Type
00 = Not Supported
X = Number of banks
(SA) + 004Bh
01 = Supported
Page Mode Type
00 = Not Supported
(SA) + 004Ch
0003h
01 = 4 Word Page
02 = 8 Word Page
03=16 Word Page
(SA) + 004Dh
0000h
ACC (Acceleration) Supply Minimum
00 = Not Supported
D7-D4: Volt
D3-D0: 100 mV
(SA) + 004Eh
0000h
ACC (Acceleration) Supply Maximum
00 = Not Supported
D7-D4: Volt
D3-D0: 100 mV
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
63
D at a
S hee t
Table 6.6 CFI Primary Vendor-Specific Extended Query (Sheet 2 of 2)
Word Address
Data
Description
WP# Protection
00h = Flash device without WP Protect (No Boot)
01h = Eight 8 kB Sectors at TOP and Bottom with WP (Dual Boot)
(SA) + 004Fh
0004h (Bottom)
0005h (Top)
02h = Bottom Boot Device with WP Protect (Bottom Boot)
03h = Top Boot Device with WP Protect (Top Boot)
04h = Uniform, Bottom WP Protect (Uniform Bottom Boot)
05h = Uniform, Top WP Protect (Uniform Top Boot)
06h = WP Protect for all sectors
07h = Uniform, Top and Bottom WP Protect
0001h
Program Suspend
00 = Not Supported
(SA) +0051h
0000h
Unlock Bypass
00 = Not Supported
(SA) + 0052h
0009h
Secured Silicon Sector (Customer OTP Area) Size 2N (bytes)
(SA) + 0050h
01 = Supported
01 = Supported
Software Features
bit 0: status register polling (1 = supported, 0 = not supported)
bit 1: DQ polling (1 = supported, 0 = not supported)
bit 2: new program suspend/resume commands (1 = supported, 0 = not supported)
(SA) + 0053h
008Fh
bit 3: word programming (1 = supported, 0 = not supported)
bit 4: bit-field programming (1 = supported, 0 = not supported)
bit 5: autodetect programming (1 = supported, 0 = not supported)
bit 6: RFU
bit 7: multiple writes per Line (1 = supported, 0 = not supported)
(SA) + 0054h
0005h
Page Size = 2N bytes
(SA) + 0055h
0006h
Erase Suspend Timeout Maximum < 2N (µs)
(SA) + 0056h
0006h
Program Suspend Timeout Maximum < 2N (µs)
FFFFh
Reserved
(SA) + 0078h
0006h
Embedded Hardware Reset Timeout Maximum < 2N (µs)
Reset with Reset Pin
(SA) + 0079h
0009h
Non-Embedded Hardware Reset Timeout Maximum < 2N (µs)
Power on Reset
(SA) + 0057h
to
(SA) + 0077h
64
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Hardware Interface
7. Signal Descriptions
7.1
Address and Data Configuration
Address and data are connected in parallel (ADP) via separate signal inputs and I/Os.
7.2
Input/Output Summary
Table 7.1 I/O Summary
Symbol
7.3
Type
Description
Hardware Reset. At VIL, causes the device to reset control logic to its standby state, ready
for reading array data.
RESET#
Input
CE#
Input
Chip Enable. At VIL, selects the device for data transfer with the host memory controller.
OE#
Input
Output Enable. At VIL, causes outputs to be actively driven. At VIH, causes outputs to be
high impedance (High-Z).
WE#
Input
Write Enable. At VIL, indicates data transfer from host to device. At VIH, indicates data
transfer is from device to host.
AMAX-A0
Input
Address inputs.
A25-A0 for S29GL01GS
A24-A0 for S29GL512S
A23-A0 for S29GL256S
A22-A0 for S29GL128S
DQ15-DQ0
Input/Output
Data inputs and outputs
WP#
Input
Write Protect. At VIL, disables program and erase functions in the lowest or highest address
64-kword (128-kB) sector of the device. At VIH, the sector is not protected. WP# has an
internal pull up; When unconnected WP# is at VIH.
RY/BY#
Output - open drain
Ready/Busy. Indicates whether an Embedded Algorithm is in progress or complete. At VIL,
the device is actively engaged in an Embedded Algorithm such as erasing or programming.
At High-Z, the device is ready for read or a new command write - requires external pull-up
resistor to detect the High-Z state. Multiple devices may have their RY/BY# outputs tied
together to detect when all devices are ready.
VCC
Power Supply
Core power supply
VIO
Power Supply
Versatile IO power supply.
VSS
Power Supply
Power supplies ground
NC
No Connect
Not Connected internally. The pin/ball location may be used in Printed Circuit Board (PCB)
as part of a routing channel.
RFU
No Connect
Reserved for Future Use. Not currently connected internally but the pin/ball location should
be left unconnected and unused by PCB routing channel for future compatibility. The pin/ball
may be used by a signal in the future.
DNU
Reserved
Do Not Use. Reserved for use by Spansion. The pin/ball is connected internally. The input
has an internal pull down resistance to VSS. The pin/ball can be left open or tied to VSS on
the PCB.
Versatile I/O Feature
The maximum output voltage level driven by, and input levels acceptable to, the device are determined by the
VIO power supply. This supply allows the device to drive and receive signals to and from other devices on the
same bus having interface signal levels different from the device core voltage.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
65
D at a
7.4
S hee t
Ready/Busy# (RY/BY#)
RY/BY# is a dedicated, open drain output pin that indicates whether an Embedded Algorithm, Power-On
Reset (POR), or Hardware Reset is in progress or complete. The RY/BY# status is valid after the rising edge
of the final WE# pulse in a command sequence, when VCC is above VCC minimum during POR, or after the
falling edge of RESET#. Since RY/BY# is an open drain output, several RY/BY# pins can be tied together in
parallel with a pull up resistor to VIO.
If the output is Low (Busy), the device is actively erasing, programming, or resetting. (This includes
programming in the Erase Suspend mode). If the output is High (Ready), the device is ready to read data
(including during the Erase Suspend mode), or is in the standby mode.
Table 5.3, Data Polling Status on page 42 shows the outputs for RY/BY# in each operation.
If an Embedded algorithm has failed (Program / Erase failure as result of max pulses or Sector is locked),
RY/BY# will stay Low (busy) until status register bits 4 and 5 are cleared and the reset command is issued.
This includes Erase or Programming on a locked sector.
7.5
Hardware Reset
The RESET# input provides a hardware method of resetting the device to standby state. When RESET# is
driven Low for at least a period of tRP, the device immediately:
 terminates any operation in progress,
 exits any ASO,
 tristates all outputs,
 resets the Status Register,
 resets the EAC to standby state.
 CE# is ignored for the duration of the reset operation (tRPH).
 To meet the Reset current specification (ICC5) CE# must be held High.
To ensure data integrity any operation that was interrupted should be reinitiated once the device is ready to
accept another command sequence.
66
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
8.
She et
Signal Protocols
The following sections describe the host system interface signal behavior and timing for the 29GL-S family
flash devices.
8.1
Interface States
Table 8.1 describes the required value of each interface signal for each interface state.
Table 8.1 Interface States
Interface State
Power-Off with Hardware
Data Protection
VCC
VIO
RESET#
CE#
OE#
WE#
AMAX-A0
DQ15-DQ0
< VLKO
≤ VCC
X
X
X
X
X
High-Z
X
X
X
X
X
High-Z
L
X
X
X
X
High-Z
H
H
X
X
X
High-Z
H
L
X
X
Valid
Output
Available
H
L
H
H
Valid
High-Z
H
L
L
H
Valid
Output
Valid
Power-On (Cold) Reset
≥ VCC min
Hardware (Warm) Reset
≥ VCC min
Interface Standby
≥ VCC min
Automatic Sleep (Notes 1, 3)
≥ VCC min
Read with Output Disable
(Note 2)
≥ VCC min
Random Read
≥ VCC min
Page Read
≥ VCC min
Write
≥ VCC min
≥ VIO min
≤ VCC
≥ VIO min
≤ VCC
≥ VIO min
≤ VCC
≥ VIO min
≤ VCC
≥ VIO min
≤ VCC
≥ VIO min
≥ VIO min
≤ VCC
≥ VIO min
≤ VCC
H
L
L
H
H
L
H
L
AMAX-A4
Valid
A3-A0
Modified
Valid
Output
Valid
Input Valid
Legend:
L = VIL
H = VIH
X = either VIL or VIH
L/H = rising edge
H/L = falling edge
Valid = all bus signals have stable L or H level
Modified = valid state different from a previous valid state
Available = read data is internally stored with output driver controlled by OE#
Notes:
1. WE# and OE# can not be at VIL at the same time.
2. Read with Output Disable is a read initiated with OE# High.
3. Automatic Sleep is a read/write operation where data has been driven on the bus for an extended period, without CE# going High and the
device internal logic has gone into standby mode to conserve power.
8.2
Power-Off with Hardware Data Protection
The memory is considered to be powered off when the core power supply (VCC) drops below the lock-out
voltage (VLKO). When VCC is below VLKO, the entire memory array is protected against a program or erase
operation. This ensures that no spurious alteration of the memory content can occur during power transition.
During a power supply transition down to Power-Off, VIO should remain less than or equal to VCC.
If VCC goes below VRST (Min) then returns above VRST (Min) to VCC minimum, the Power-On Reset interface
state is entered and the EAC starts the Cold Reset Embedded Algorithm.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
67
D at a
8.3
8.3.1
S hee t
Power Conservation Modes
Interface Standby
Standby is the default, low power, state for the interface while the device is not selected by the host for data
transfer (CE# = High). All inputs are ignored in this state and all outputs except RY/BY# are high impedance.
RY/BY# is a direct output of the EAC, not controlled by the Host Interface.
8.3.2
Automatic Sleep
The automatic sleep mode reduces device interface energy consumption to the sleep level (ICC6) following
the completion of a random read access time. The device automatically enables this mode when addresses
remain stable for tACC + 30 ns. While in sleep mode, output data is latched and always available to the
system. Output of the data depends on the level of the OE# signal but, the automatic sleep mode current is
independent of the OE# signal level. Standard address access timings (tACC or tPACC) provide new data when
addresses are changed. ICC6 in DC Characteristics on page 74 represents the automatic sleep mode current
specification.
Automatic sleep helps reduce current consumption especially when the host system clock is slowed for power
reduction. During slow system clock periods, read and write cycles may extend many times their length
versus when the system is operating at high speed. Even though CE# may be Low throughout these
extended data transfer cycles, the memory device host interface will go to the Automatic Sleep current at tACC
+ 30 ns. The device will remain at the Automatic Sleep current for tASSB. Then the device will transition to the
standby current level. This keeps the memory at the Automatic Sleep or standby power level for most of the
long duration data transfer cycles, rather than consuming full read power all the time that the memory device
is selected by the host system.
However, the EAC operates independent of the automatic sleep mode of the host interface and will continue
to draw current during an active Embedded Algorithm. Only when both the host interface and EAC are in their
standby states is the standby level current achieved.
8.4
8.4.1
Read
Read With Output Disable
When the CE# signal is asserted Low, the host system memory controller begins a read or write data transfer.
Often there is a period at the beginning of a data transfer when CE# is Low, Address is valid, OE# is High,
and WE# is High. During this state a read access is assumed and the Random Read process is started while
the data outputs remain at high impedance. If the OE# signal goes Low, the interface transitions to the
Random Read state, with data outputs actively driven. If the WE# signal is asserted Low, the interface
transitions to the Write state. Note, OE# and WE# should never be Low at the same time to ensure no data
bus contention between the host system and memory.
68
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
8.4.2
She et
Random (Asynchronous) Read
When the host system interface selects the memory device by driving CE# Low, the device interface leaves
the Standby state. If WE# is High when CE# goes Low, a random read access is started. The data output
depends on the address map mode and the address provided at the time the read access is started.
The data appears on DQ15-DQ0 when CE# is Low, OE# is Low, WE# remains High, address remains stable,
and the asynchronous access times are satisfied. Address access time (tACC) is equal to the delay from
stable addresses to valid output data. The chip enable access time (tCE) is the delay from stable CE# to valid
data at the outputs. In order for the read data to be driven on to the data outputs the OE# signal must be Low
at least the output enable time (tOE) before valid data is available.
At the completion of the random access time from CE# active (tCE), address stable (tACC), or OE# active
(tOE), whichever occurs latest, the data outputs will provide valid read data from the currently active address
map mode. If CE# remains Low and any of the AMAX to A4 address signals change to a new value, a new
random read access begins. If CE# remains Low and OE# goes High the interface transitions to the Read
with Output Disable state. If CE# remains Low, OE# goes High, and WE# goes Low, the interface transitions
to the Write state. If CE# returns High, the interface goes to the Standby state. Back to Back accesses, in
which CE# remains Low between accesses, requires an address change to initiate the second access.
See Asynchronous Read Operations on page 80.
8.4.3
Page Read
After a Random Read access is completed, if CE# remains Low, OE# remains Low, the AMAX to A4 address
signals remain stable, and any of the A3 to A0 address signals change, a new access within the same Page
begins. The Page Read completes much faster (tPACC) than a Random Read access.
8.5
8.5.1
Write
Asynchronous Write
When WE# goes Low after CE is Low, there is a transition from one of the read states to the Write state. If
WE# is Low before CE# goes Low, there is a transition from the Standby state directly to the Write state
without beginning a read access.
When CE# is Low, OE# is High, and WE# goes Low, a write data transfer begins. Note, OE# and WE# should
never be Low at the same time to ensure no data bus contention between the host system and memory.
When the asynchronous write cycle timing requirements are met the WE# can go High to capture the address
and data values in to EAC command memory.
Address is captured by the falling edge of WE# or CE#, whichever occurs later. Data is captured by the rising
edge of WE# or CE#, whichever occurs earlier.
When CE# is Low before WE# goes Low and stays Low after WE# goes High, the access is called a WE#
controlled Write. When WE# is High and CE# goes High, there is a transition to the Standby state. If CE#
remains Low and WE# goes High, there is a transition to the Read with Output Disable state.
When WE# is Low before CE# goes Low and remains Low after CE# goes High, the access is called a CE#
controlled Write. A CE# controlled Write transitions to the Standby state.
If WE# is Low before CE# goes Low, the write transfer is started by CE# going Low. If WE# is Low after CE#
goes High, the address and data are captured by the rising edge of CE#. These cases are referred to as CE#
controlled write state transitions.
Write followed by Read accesses, in which CE# remains Low between accesses, requires an address
change to initiate the following read access.
Back to Back accesses, in which CE# remains Low between accesses, requires an address change to initiate
the second access.
The EAC command memory array is not readable by the host system and has no ASO. The EAC examines
the address and data in each write transfer to determine if the write is part of a legal command sequence.
When a legal command sequence is complete the EAC will initiate the appropriate EA.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
69
D at a
8.5.2
S hee t
Write Pulse “Glitch” Protection
Noise pulses of less than 5 ns (typical) on WE# will not initiate a write cycle.
8.5.3
Logical Inhibit
Write cycles are inhibited by holding OE# at VIL, or CE# at VIH, or WE# at VIH. To initiate a write cycle, CE#
and WE# must be Low (VIL) while OE# is High (VIH).
70
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
9.
She et
Electrical Specifications
9.1
Absolute Maximum Ratings
Table 9.1 Absolute Maximum Ratings
Storage Temperature Plastic Packages
-65°C to +150°C
Ambient Temperature with Power Applied
-65°C to +125°C
Voltage with Respect to Ground
All pins other than RESET# (Note 1)
-0.5V to (VIO + 0.5V)
RESET# (Note 1)
-0.5V to (VCC + 0.5V)
Output Short Circuit Current (Note 2)
100 mA
VCC
-0.5V to +4.0V
VIO
-0.5V to +4.0V
Notes:
1. Minimum DC voltage on input or I/O pins is -0.5V. During voltage transitions, input or I/O pins may undershoot VSS to -2.0V for periods of
up to 20 ns. See Figure 9.3 on page 73. Maximum DC voltage on input or I/O pins is VCC +0.5V. During voltage transitions, input or I/O
pins may overshoot to VCC +2.0V for periods up to 20 ns. See Figure 9.4 on page 73
2. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second.
3. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only;
functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is
not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability.
9.2
Latchup Characteristics
This product complies with JEDEC standard JESD78C latchup testing requirements.
9.3
9.3.1
Operating Ranges
Temperature Ranges
Industrial (I) Devices
Ambient Temperature (TA)
9.3.2
-40°C to +85°C
Power Supply Voltages
VCC
VIO
2.7V to 3.6V
1.65V to VCC + 200 mV
Operating ranges define those limits between which the functionality of the device is guaranteed.
9.3.3
Power-Up and Power-Down
During power-up or power-down VCC must always be greater than or equal to VIO (VCC ≥ VIO).
The device ignores all inputs until a time delay of tVCS has elapsed after the moment that VCC and VIO both
rise above, and stay above, the minimum VCC and VIO thresholds. During tVCS the device is performing power
on reset operations.
During power-down or voltage drops below VCC Lockout maximum (VLKO), the VCC and VIO voltages must
drop below VCC Reset (VRST) minimum for a period of tPD for the part to initialize correctly when VCC and VIO
again rise to their operating ranges. See Figure 9.2 on page 72. If during a voltage drop the VCC stays above
VLKO maximum the part will stay initialized and will work correctly when VCC is again above VCC minimum. If
the part locks up from improper initialization, a hardware reset can be used to initialize the part correctly.
Normal precautions must be taken for supply decoupling to stabilize the VCC and VIO power supplies. Each
device in a system should have the VCC and VIO power supplies decoupled by a suitable capacitor close to
the package connections (this capacitor is generally on the order of 0.1 µF). At no time should VIO be greater
then 200 mV above VCC (VCC ≥ VIO - 200 mV).
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
71
D at a
S hee t
Table 9.2 Power-Up/Power-Down Voltage and Timing
Symbol
Parameter
Min
Max
Unit
VCC
VCC Power Supply
2.7
3.6
V
VLKO
VCC level below which re-initialization is required (Note 1)
2.25
2.5
V
VRST
VCC and VIO Low voltage needed to ensure initialization will occur (Note 1)
1.0
V
tVCS
VCC and VIO ≥ minimum to first access (Note 1)
300
µs
tPD
Duration of VCC ≤ VRST(min) (Note 1)
15
µs
Note:
1. Not 100% tested.
Figure 9.1 Power-up
P o w e r S u p p ly
V o lta g e
V cc (m a x)
V cc (m in )
V IO (m a x)
V IO (m in)
V cc
tVC S
V IO
F u ll D e vice A ccess
tim e
Figure 9.2 Power-down and Voltage Drop
V C C a n d V IO
V C C (m a x)
N o D e vice A cce ss A llo w e d
V C C (m in )
tVC S
V L K O (m a x)
F u ll D e vice
A ccess
A llo w e d
V R S T (m in )
tP D
tim e
72
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
9.3.4
She et
Input Signal Overshoot
Figure 9.3 Maximum Negative Overshoot Waveform
20 ns
20 ns
VIL max
VIL min
–2 .0 V
20 n s
Figure 9.4 Maximum Positive Overshoot Waveform
20 ns
VIO + 2.0 V
VIH max
VIH min
20 ns
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
20 ns
73
D at a
9.4
S hee t
DC Characteristics
Table 9.3 DC Characteristics (-40°C to +85°C)
Parameter
Typ
(Note 2)
Max
Unit
VIN = VSS to VCC, VCC = VCC max
+0.02
±1.0
µA
Description
Test Conditions
Min
ILI
Input Load Current
ILO
Output Leakage Current
VOUT = VSS to VCC, VCC = VCC max
+0.02
±1.0
µA
ICC1
VCC Active Read Current
CE# = VIL, OE# = VIH, Address
switching@ 5 MHz, VCC = VCC max
55
60
mA
ICC2
VCC Intra-Page Read Current
CE# = VIL, OE# = VIH, Address
switching@ 33 MHz, VCC = VCC max
9
25
mA
ICC3
VCC Active Erase/Program
Current (Notes 1, 2)
CE# = VIL, OE# = VIH, VCC = VCC max
45
100
mA
ICC4
VCC Standby Current
CE#, RESET#, OE# = VIH, VIH = VIO
VIL = VSS, VCC = VCC max
70
100
µA
ICC5
VCC Reset Current (Notes 2, 7)
CE# = VIH, RESET# = VIL,
VCC = VCC max
10
20
mA
VIH = VIO, VIL = VSS ,
VCC = VCC max, tACC + 30 ns
3
6
mA
VIH = VIO, VIL = VSS,
VCC = VCC max, tASSB
100
150
µA
RESET# = VIO, CE# = VIO, OE# = VIO,
VCC = VCC max,
53
80
mA
-0.5
0.3 x VIO
V
0.7 x VIO
VIO + 0.4
V
0.15 x VIO
V
ICC6
Automatic Sleep Mode (Note 3)
ICC7
VCC Current during power up
(Notes 2, 6)
VIL
Input Low Voltage (Note 4)
VIH
Input High Voltage (Note 4)
VOL
Output Low Voltage (Notes 4, 8)
IOL = 100 µA for DQ15-DQ0;
IOL = 2 mA for RY/BY#
VOH
Output High Voltage (Note 4)
IOH = 100 µA
VLKO
Low VCC Lock-Out Voltage
(Note 2)
VRST
Low VCC Power on Reset Voltage
(Note 2)
0.85 x VIO
V
2.25
2.5
1.0
V
V
Notes:
1. ICC active while Embedded Algorithm is in progress.
2. Not 100% tested.
3. Automatic sleep mode enables the lower power mode when addresses remain stable for the specified designated time.
4. VIO = 1.65V to VCC or 2.7V to VCC depending on the model.
5. VCC = 3V and VIO = 3V or 1.8V. When VIO is at 1.8V, I/O pins cannot operate at >1.8V.
6. During power-up there are spikes of current demand, the system needs to be able to supply this current to insure the part initializes
correctly.
7. If an embedded operation is in progress at the start of reset, the current consumption will remain at the embedded operation specification
until the embedded operation is stopped by the reset. If no embedded operation is in progress when reset is started, or following the
stopping of an embedded operation, ICC5 will be drawn during the remainder of tRPH. After the end of tRPH the device will go to standby
mode until the next read or write.
8. The recommended pull-up resistor for RY/BY# output is 5k to 10k Ohms.
74
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Table 9.4 DC Characteristics (-40°C to +105°C)
Parameter
Description
Test Conditions
Min
Typ
(Note 2)
Max
Unit
ILI
Input Load Current
VIN = VSS to VCC, VCC = VCC max
+0.02
±1.0
µA
ILO
Output Leakage Current
VOUT = VSS to VCC, VCC = VCC max
+0.02
±1.0
µA
ICC1
VCC Active Read Current
CE# = VIL, OE# = VIH, Address
switching@ 5 MHz, VCC = VCC max
55
60
mA
ICC2
VCC Intra-Page Read Current
CE# = VIL, OE# = VIH, Address
switching@ 33 MHz, VCC = VCC max
9
25
mA
ICC3
VCC Active Erase/Program
Current (Notes 1, 2)
CE# = VIL, OE# = VIH, VCC = VCC max
45
100
mA
ICC4
VCC Standby Current
CE#, RESET#, OE# = VIH, VIH = VIO
VIL = VSS, VCC = VCC max
70
200
µA
ICC5
VCC Reset Current (Notes 2, 7)
CE# = VIH, RESET# = VIL,
VCC = VCC max
10
20
mA
VIH = VIO, VIL = VSS ,
VCC = VCC max, tACC + 30 ns
3
6
mA
VIH = VIO, VIL = VSS,
VCC = VCC max, tASSB
100
200
µA
RESET# = VIO, CE# = VIO, OE# = VIO,
VCC = VCC max,
53
80
mA
ICC6
Automatic Sleep Mode (Note 3)
ICC7
VCC Current during power up
(Notes 2, 6)
VIL
Input Low Voltage (Note 4)
-0.5
0.3 x VIO
V
VIH
Input High Voltage (Note 4)
0.7 x VIO
VIO + 0.4
V
VOL
Output Low Voltage (Notes 4, 8)
IOL = 100 µA for DQ15-DQ0;
IOL = 2 mA for RY/BY#
0.15 x VIO
V
VOH
Output High Voltage (Note 4)
IOH = 100 µA
VLKO
Low VCC Lock-Out Voltage
(Note 2)
VRST
Low VCC Power on Reset Voltage
(Note 2)
0.85 x VIO
V
2.25
2.5
1.0
V
V
Notes:
1. ICC active while Embedded Algorithm is in progress.
2. Not 100% tested.
3. Automatic sleep mode enables the lower power mode when addresses remain stable for the specified designated time.
4. VIO = 1.65V to VCC or 2.7V to VCC depending on the model.
5. VCC = 3V and VIO = 3V or 1.8V. When VIO is at 1.8V, I/O pins cannot operate at >1.8V.
6. During power-up there are spikes of current demand, the system needs to be able to supply this current to insure the part initializes
correctly.
7. If an embedded operation is in progress at the start of reset, the current consumption will remain at the embedded operation specification
until the embedded operation is stopped by the reset. If no embedded operation is in progress when reset is started, or following the
stopping of an embedded operation, ICC7 will be drawn during the remainder of tRPH. After the end of tRPH the device will go to standby
mode until the next read or write.
8. The recommended pull-up resistor for RY/BY# output is 5k to 10k Ohms.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
75
D at a
9.5
S hee t
Capacitance Characteristics
Table 9.5 Connector Capacitance for FBGA (LAA) Package
Parameter Symbol
Parameter Description
Test Setup
Typ
Max
Unit
CIN
Input Capacitance
VIN = 0
8
9
pF
COUT
Output Capacitance
VOUT = 0
5
7
pF
CIN2
Control Pin Capacitance
VIN = 0
4
8
pF
RY/BY#
Output Capacitance
VOUT = 0
3
4
pF
Notes:
1. Sampled, not 100% tested.
2. Test conditions TA = 25°C, f = 1.0 MHz.
Table 9.6 Connector Capacitance for FBGA (LAE) Package
Parameter Symbol
Parameter Description
Test Setup
Typ
Max
Unit
CIN
Input Capacitance
VIN = 0
7
8
pF
COUT
Output Capacitance
VOUT = 0
5
6
pF
CIN2
Control Pin Capacitance
VIN = 0
3
7
pF
RY/BY#
Output Capacitance
VOUT = 0
3
4
pF
Notes:
1. Sampled, not 100% tested.
2. Test conditions TA = 25°C, f = 1.0 MHz.
Table 9.7 Connector Capacitance for TSOP Package
Parameter Symbol
Parameter Description
Test Setup
Typ
Max
Unit
CIN
Input Capacitance
VIN = 0
7
8
pF
COUT
Output Capacitance
VOUT = 0
5
6
pF
CIN2
Control Pin Capacitance
VIN = 0
3
7
pF
RY/BY#
Output Capacitance
VOUT = 0
3
4
pF
Notes:
1. Sampled, not 100% tested.
2. Test conditions TA = 25°C, f = 1.0 MHz.
76
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
10. Timing Specifications
10.1
Key to Switching Waveforms
Waveform
Inputs
Outputs
Steady
Changing from H to L
Changing from L to H
10.2
Don't Care, Any Change Permitted
Changing, State Unknown
Does Not Apply
Center Line is High Impedance State (High-Z)
AC Test Conditions
Figure 10.1 Test Setup
Device
Under
Test
CL
Table 10.1 Test Specification
All Speeds
Units
Output Load Capacitance, CL
Parameter
30
pF
Input Rise and Fall Times (Note 1)
1.5
ns
0.0-VIO
V
Input timing measurement reference levels
VIO/2
V
Output timing measurement reference levels
VIO/2
V
Input Pulse Levels
Note:
1. Measured between VIL max and VIH min.
Figure 10.2 Input Waveforms and Measurement Levels
VIO
0.0 V
Input
October 9, 2013 S29GL_128S_01GS_00_08
0.5 VIO
Measurement Level
GL-S MirrorBit® Family
0.5 VIO
Output
77
D at a
10.3
S hee t
Power-On Reset (POR) and Warm Reset
Normal precautions must be taken for supply decoupling to stabilize the VCC and VIO power supplies. Each
device in a system should have the VCC and VIO power supplies decoupled by a suitable capacitor close to
the package connections (this capacitor is generally on the order of 0.1 µF).
Table 10.2 Power ON and Reset Parameters
Parameter
Description
Limit
Value
Unit
Min
300
µs
VIO Setup Time to first access (Notes 1, 2)
Min
300
µs
RESET# Low to CE# Low
Min
35
µs
tVCS
VCC Setup Time to first access (Notes 1, 2)
tVIOS
tRPH
tRP
RESET# Pulse Width
Min
200
ns
tRH
Time between RESET# (High) and CE# (low)
Min
50
ns
tCEH
CE# Pulse Width High
Min
20
ns
Notes:
1. Not 100% tested.
2. Timing measured from VCC reaching VCC minimum and VIO reaching VIO minimum to VIH on Reset and VIL on CE#.
3. RESET# Low is optional during POR. If RESET is asserted during POR, the later of tRPH, tVIOS, or tVCS will determine when CE# may go
Low. If RESET# remains Low after tVIOS, or tVCS is satisfied, tRPH is measured from the end of tVIOS, or tVCS. RESET must also be High
tRH before CE# goes Low.
4. VCC ≥ VIO - 200 mV during power-up.
5. VCC and VIO ramp rate can be non-linear.
6. Sum of tRP and tRH must be equal to or greater than tRPH.
10.3.1
Power-On (Cold) Reset (POR)
During the rise of power supplies the VIO supply voltage must remain less than or equal to the VCC supply
voltage. VIH also must remain less than or equal to the VIO supply.
The Cold Reset Embedded Algorithm requires a relatively long, hundreds of µs, period (tVCS) to load all of the
EAC algorithms and default state from non-volatile memory. During the Cold Reset period all control signals
including CE# and RESET# are ignored. If CE# is Low during tVCS the device may draw higher than normal
POR current during tVCS but the level of CE# will not affect the Cold Reset EA. CE# or OE# must transition
from High to Low after tVCS for a valid read or write operation. RESET# may be High or Low during tVCS. If
RESET# is Low during tVCS it may remain Low at the end of tVCS to hold the device in the Hardware Reset
state. If RESET# is High at the end of tVCS the device will go to the Standby state.
When power is first applied, with supply voltage below VRST then rising to reach operating range minimum,
internal device configuration and warm reset activities are initiated. CE# is ignored for the duration of the POR
operation (tVCS or tVIOS). RESET# Low during this POR period is optional. If RESET# is driven Low during
POR it must satisfy the Hardware Reset parameters tRP and tRPH. In which case the Reset operations will be
completed at the later of tVCS or tVIOS or tRPH.
During Cold Reset the device will draw ICC7 current.
Figure 10.3 Power-Up Diagram
tVCS
VCC
tVIOS
VIO
RESET#
tRH
tCEH
CE#
78
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
10.3.2
She et
Hardware (Warm) Reset
During Hardware Reset (tRPH) the device will draw ICC5 current.
When RESET# continues to be held at VSS, the device draws CMOS standby current (ICC4). If RESET# is
held at VIL, but not at VSS, the standby current is greater.
If a Cold Reset has not been completed by the device when RESET# is asserted Low after tVCS, the Cold
Reset# EA will be performed instead of the Warm RESET#, requiring tVCS time to complete.
See Figure 10.4, Hardware Reset on page 79.
After the device has completed POR and entered the Standby state, any later transition to the Hardware
Reset state will initiate the Warm Reset Embedded Algorithm. A Warm Reset is much shorter than a Cold
Reset, taking tens of µs (tRPH) to complete. During the Warm Reset EA, any in progress Embedded Algorithm
is stopped and the EAC is returned to its POR state without reloading EAC algorithms from non-volatile
memory. After the Warm Reset EA completes, the interface will remain in the Hardware Reset state if
RESET# remains Low. When RESET# returns High the interface will transit to the Standby state. If RESET#
is High at the end of the Warm Reset EA, the interface will directly transit to the Standby state.
If POR has not been properly completed by the end of tVCS, a later transition to the Hardware Reset state will
cause a transition to the Power-on Reset interface state and initiate the Cold Reset Embedded Algorithm.
This ensures the device can complete a Cold Reset even if some aspect of the system Power-On voltage
ramp-up causes the POR to not initiate or complete correctly. The RY/BY# pin is Low during cold or warm
reset as an indication that the device is busy performing reset operations.
Hardware Reset is initiated by the RESET# signal going to VIL.
Figure 10.4 Hardware Reset
tRP
RESET#
tRH
tRPH
tCEH
CE#
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
79
D at a
10.4
S hee t
AC Characteristics
10.4.1
Asynchronous Read Operations
Table 10.3 Read Operation VIO = VCC = 2.7V to 3.6V (-40°C to +85°C)
Parameter
Speed Option
Description
JEDEC
Std
tAVAV
tRC
Read Cycle Time (Note 1)
tAVQV
tACC
Address to Output Delay
tELQV
tCE
Chip Enable to Output Delay
Test Setup
Unit
128 Mb, 256 Mb
90
100
110
Min
ns
CE# = VIL
OE# = VIL
100
128 Mb, 256 Mb
90
OE# = VIL
110
100
Max
ns
512 Mb, 1 Gb
100
90
110
100
Max
ns
512 Mb, 1 Gb
100
128 Mb, 256 Mb
tGLQV
100
512 Mb, 1 Gb
128 Mb, 256 Mb
tPACC
90
Page Access Time
15
110
20
Max
ns
512 Mb, 1 Gb
15
20
tOE
Output Enable to Output Delay
Max
25
ns
tAXQX
tOH
Output Hold time from addresses, CE# or OE#,
Whichever Occurs First
Min
0
ns
tEHQZ
tDF
Chip Enable or Output Enable to Output High-Z
(Note 1)
Max
15
ns
Read
Min
0
ns
Toggle and
Data# Polling
Min
10
ns
Typ
5
µs
Max
8
µs
tOEH
Output Enable Hold Time
(Note 1)
tASSB
Automatic Sleep to Standby time (Note 1)
CE# = VIL,
Address stable
Note:
1. Not 100% tested.
Table 10.4 Read Operation VIO = 1.65V to VCC, VCC = 2.7V to 3.6V (-40°C to +85°C)
Parameter
Speed Options
Description
JEDEC
Std
tAVAV
tRC
Read Cycle Time (Note 1)
tAVQV
tACC
Address to Output Delay
tELQV
tCE
Chip Enable to Output Delay
Test Setup
Unit
128 Mb, 256 Mb
110
100
110
120
Min
ns
512 Mb, 1 Gb
CE# = VIL
OE# = VIL
110
128 Mb, 256 Mb
100
OE# = VIL
120
110
Max
ns
512 Mb, 1 Gb
110
128 Mb, 256 Mb
100
120
110
Max
ns
512 Mb, 1 Gb
110
128 Mb, 256 Mb
tPACC
100
Page Access Time
25
120
30
Max
512 Mb, 1 Gb
ns
25
30
tOE
Output Enable to Output Delay
Max
35
ns
tAXQX
tOH
Output Hold time from addresses, CE# or OE#,
Whichever Occurs First
Min
0
ns
tEHQZ
tDF
Chip Enable or Output Enable to Output High-Z
(Note 1)
Max
20
ns
Read
Min
0
ns
Toggle and
Data# Polling
Min
10
ns
Typ
5
µs
Max
8
µs
tGLQV
tOEH
Output Enable Hold Time
(Note 1)
tASSB
Automatic Sleep to Standby time (Note 1)
CE# = VIL,
Address stable
Note:
1. Not 100% tested.
80
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Table 10.5 Read Operation VIO = VCC = 2.7V to 3.6V (-40°C to +105°C)
Parameter
Speed Option
Description
JEDEC
Std
tAVAV
tRC
Read Cycle Time (Note 1)
tAVQV
tACC
Address to Output Delay
tELQV
tCE
Chip Enable to Output
Delay
Test Setup
Unit
100
128 Mb, 256 Mb
100
tGLQV
120
110
Min
ns
512 Mb, 1 Gb
CE# = VIL
OE# = VIL
110
128 Mb, 256 Mb
100
110
ns
512 Mb, 1 Gb
110
128 Mb, 256 Mb
OE# = VIL
120
Max
100
120
110
Max
ns
512 Mb, 1 Gb
110
128 Mb, 256 Mb
tPACC
110
Page Access Time
15
120
20
Max
ns
512 Mb, 1 Gb
15
20
tOE
Output Enable to Output Delay
Max
25
ns
tAXQX
tOH
Output Hold time from addresses, CE# or
OE#, Whichever Occurs First
Min
0
ns
tEHQZ
tDF
Chip Enable or Output Enable to Output
High-Z (Note 1)
Max
15
ns
Read
Min
0
ns
Toggle and
Data# Polling
Min
10
ns
tOEH
Output Enable Hold Time
(Note 1)
tASSB
Automatic Sleep to Standby time (Note 1)
CE# = VIL, Address
stable
Typ
5
µs
Max
8
µs
Note:
1. Not 100% tested.
Table 10.6 Read Operation VIO = 1.65V to VCC, VCC = 2.7V to 3.6V (-40°C to +105°C)
Parameter
Speed Option
Description
JEDEC
Std
tAVAV
tRC
Read Cycle Time (Note 1)
tAVQV
tACC
Address to Output Delay
tELQV
tCE
Chip Enable to Output
Delay
Test Setup
Unit
110
128 Mb, 256 Mb
110
130
120
Min
ns
512 Mb, 1 Gb
CE# = VIL
OE# = VIL
120
128 Mb, 256 Mb
110
120
ns
120
128 Mb, 256 Mb
OE# = VIL
130
Max
512 Mb, 1 Gb
110
130
120
Max
ns
512 Mb, 1 Gb
120
128 Mb, 256 Mb
tPACC
120
Page Access Time
25
130
30
Max
512 Mb, 1 Gb
ns
25
30
tOE
Output Enable to Output Delay
Max
35
ns
tAXQX
tOH
Output Hold time from addresses, CE# or
OE#, Whichever Occurs First
Min
0
ns
tEHQZ
tDF
Chip Enable or Output Enable to Output
High-Z (Note 1)
Max
20
ns
Read
Min
0
ns
Toggle and
Data# Polling
Min
10
ns
tGLQV
tOEH
Output Enable Hold Time
(Note 1)
tASSB
Automatic Sleep to Standby time (Note 1)
CE# = VIL, Address
stable
Typ
5
µs
Max
8
µs
Note:
1. Not 100% tested.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
81
D at a
S hee t
Figure 10.5 Back to Back Read (tACC) Operation Timing Diagram
tACC
tOH
Amax-A0
tDF
tCE
tOH
CE#
tDF
tOE
tOH
OE#
DQ15-DQ0
Figure 10.6 Back to Back Read Operation (tRC)Timing Diagram
tRC
tACC
tOH
Amax-A0
tCE
CE#
tOE
tOH
tDF
OE#
DQ15-DQ0
Note:
Back to Back operations, in which CE# remains Low between accesses, requires an address change to initiate the second access.
Figure 10.7 Page Read Timing Diagram
tACC
Amax-A4
A3-A0
tCE
CE#
tOE
OE#
tPACC
DQ15-DQ0
Note:
Word Configuration: Toggle A0, A1, A2, and A3.
82
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
10.4.2
She et
Asynchronous Write Operations
Table 10.7 Write Operations
Parameter
VIO = 2.7V to
VCC
Description
VIO = 1.65V
to VCC
Unit
JEDEC
Std
tAVAV
tWC
Write Cycle Time (Note 1)
Min
60
ns
tAVWL
tAS
Address Setup Time
Min
0
ns
tASO
Address Setup Time to OE# Low during toggle bit polling
Min
15
ns
tAH
Address Hold Time
Min
45
ns
tAHT
Address Hold Time From CE# or OE# High during toggle
bit polling
Min
0
ns
tDVWH
tDS
Data Setup Time
Min
30
ns
tWHDX
tDH
Data Hold Time
Min
0
ns
tOEPH
Output Enable High during toggle bit polling or following
status register read.
Min
20
ns
tGHWL
Read Recovery Time Before Write
(OE# High to WE# Low)
Min
0
ns
tWLAX
tGHWL
tELWL
tCS
CE# Setup Time
Min
0
ns
tWHEH
tCH
CE# Hold Time
Min
0
ns
tWLWH
tWP
WE# Pulse Width
Min
25
ns
tWHWL
tWPH
WE# Pulse Width High
Min
20
ns
Note:
1. Not 100% tested.
Figure 10.8 Back to Back Write Operation Timing Diagram
tWC
Amax-A0
tAS
tAH
tCS
tCH
CE#
OE#
tWP
tWPH
WE#
tDS
tDH
DQ15-DQ0
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
83
D at a
S hee t
Figure 10.9 Back to Back (CE#VIL) Write Operation Timing Diagram
tWC
Amax-A0
tAS
tAH
tCS
CE#
OE#
tWP
tWPH
WE#
tDS
tDH
DQ15-DQ0
Figure 10.10 Write to Read (tACC) Operation Timing Diagram
tAH
tAS
tSR_W
tACC
tOH
Amax-A0
tOH
tCS
tDF
CE#
tOH
tOEH
tOE
tDF
OE#
tWP
WE#
tDH
tDS
DQ15-DQ0
84
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Figure 10.11 Write to Read (tCE) Operation Timing Diagram
tAH
tAS
tSR_W
tACC
tOH
Amax-A0
tOH
tCS
tCH
tCE
tDF
CE#
tOH
tOEH
tOE
tDF
OE#
tWP
WE#
tDH
tDS
DQ15-DQ0
Figure 10.12 Read to Write (CE# VIL) Operation Timing Diagram
tAS
tACC
tOH
tAH
Amax-A0
tCE
tCH
CE#
tGHWL
tOH
tOE
tDF
OE#
tWP
WE#
tDS
tDH
DQ15-DQ0
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
85
D at a
S hee t
Figure 10.13 Read to Write (CE# Toggle) Operation Timing Diagram
tAS
tACC
tOH
tAH
Amax-A0
tOH
tCE
tDF
tCS
tCH
CE#
tGHWL
tOH
tOE
tDF
OE#
tWP
WE#
tDH
tDS
DQ15-DQ0
Table 10.8 Erase/Program Operations
Parameter
VIO = 2.7V
to VCC
Description
JEDEC
Std
tWHWH1
tWHWH1
tWHWH2
tWHWH2
VIO = 1.65V
to VCC
Unit
Write Buffer Program Operation
Typ
(Note 3)
µs
Effective Write Buffer Program Operation per Word
Typ
(Note 3)
µs
Program Operation per Word or Page
Typ
(Note 3)
µs
Sector Erase Operation (Note 1)
Typ
(Note 3)
ms
tBUSY
Erase/Program Valid to RY/BY# Delay
Max
80
ns
tSR/W
Latency between Read and Write operations (Note 2)
Min
10
ns
tESL
Erase Suspend Latency
Max
(Note 3)
µs
tPSL
Program Suspend Latency
Max
(Note 3)
µs
tRB
RY/BY# Recovery Time
Min
0
µs
Notes:
1. Not 100% tested.
2. Upon the rising edge of WE#, must wait tSR/W before switching to another address.
3. See Table 5.4 on page 46 and Table 5.5 on page 47 for specific values.
86
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Figure 10.14 Program Operation Timing Diagram
Program Command Sequence (last two cycles)
tAS
tWC
555h
Addresses
Read Status Data (last two cycles)
PA
PA
PA
tAH
CE#
tCH
OE#
tWHWH1
tWP
WE#
tWPH
tCS
tDS
tDH
PD
A0h
Data
Status
DOUT
tBUSY
tRB
RY/BY#
Note:
1. PA = program address, PD = program data, DOUT is the true data at the program address.
Figure 10.15 Chip/Sector Erase Operation Timing Diagram
Erase Command Sequence (last two cycles)
tAS
tWC
Addresses
Read Status Data (last two cycles)
2AAh
VA
SA
VA
555h for chip erase
tAH
CE#
tCH
OE#
tWP
WE#
tWPH
tCS
tWHWH2
tDS
tDH
Data
55h
In
Progress
30h
Complete
10 for Chip Erase
tBUSY
tRB
RY/BY#
Note:
1. SA = sector address (for sector erase), VA = valid address for reading status data.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
87
D at a
S hee t
Figure 10.16 Data# Polling Timing Diagram (During Embedded Algorithms)
tRC
Addresses
VA
VA
VA
tACC
tCE
CE#
tCH
tOE
OE#
tOEH
tDF
WE#
tOH
High Z
DQ7
Complement
Complement
True
Valid Data
Status Data
Status Data
True
Valid Data
High Z
DQ6–DQ0
tBUSY
RY/BY#
Note:
1. VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data read cycle.
Figure 10.17 Toggle Bit Timing Diagram (During Embedded Algorithms)
tAHT
tAS
Addresses
tAHT
tASO
CE#
tCEPH
tOEH
WE#
tOEPH
OE#
tDH
DQ2 and DQ6
tOE
Valid Data
Valid
Status
Valid
Status
Valid
Status
(first read)
(second read)
(stops toggling)
Valid Data
RY/BY#
Note:
1. DQ6 will toggle at any read address while the device is busy. DQ2 will toggle if the address is within the actively erasing sector.
Figure 10.18 DQ2 vs. DQ6 Relationship Diagram
Enter
Embedded
Erasing
WE#
Erase
Suspend
Erase
Enter Erase
Suspend Program
Erase Suspend
Read
Erase
Suspend
Program
Erase
Resume
Erase Suspend
Read
Erase
Erase
Complete
DQ6
DQ2
Note:
1. The system may use OE# or CE# to toggle DQ2 and DQ6. DQ2 toggles only when read at an address within the erase-suspended sector.
88
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
10.4.3
She et
Alternate CE# Controlled Write Operations
Table 10.9 Alternate CE# Controlled Write Operations
Parameter
VIO = 2.7V to
VCC
Description
VIO = 1.65V
to VCC
Unit
JEDEC
Std
tAVAV
tWC
Write Cycle Time (Note 1)
Min
60
tAVWL
tAS
Address Setup Time
Min
0
ns
tASO
Address Setup Time to OE# Low during toggle bit polling
Min
15
ns
tAH
Address Hold Time
Min
45
ns
tAHT
Address Hold Time From CE# or OE# High during toggle
bit polling
Min
0
ns
tDS
Data Setup Time
Min
30
ns
tDH
ns
tWLAX
tDVWH
tWHDX
tGHEK
ns
Data Hold Time
Min
0
tCEPH
CE# High during toggle bit polling
Min
20
ns
t0EPH
OE# High during toggle bit polling
Min
20
ns
tGHEL
Read Recovery Time Before Write
(OE# High to WE# Low)
Min
0
ns
tWLEL
tWS
WE# Setup Time
Min
0
ns
tELWH
tWH
WE# Hold Time
Min
0
ns
tELEH
tCP
CE# Pulse Width
Min
25
ns
tEHEL
tCPH
CE# Pulse Width High
Min
20
ns
Note:
1. Not 100% tested.
Figure 10.19 Back to Back (CE#) Write Operation Timing Diagram
tWC
Amax-A0
tAS
tAH
tCP
tCPH
CE#
OE#
tWS
tWH
WE#
tDS
tDH
DQ15-DQ0
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
89
D at a
S hee t
Figure 10.20 (CE#) Write to Read Operation Timing Diagram
tWC
tAS
tACC
Amax-A0
tAH
tCE
tDF
CE#
tOEH
tOE
OE#
tWS
tWH
WE#
tDH
tDS
tOH
DQ15-DQ0
90
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
11. Physical Interface
11.1
56-Pin TSOP
11.1.1
Connection Diagram
Figure 11.1 56-Pin Standard TSOP
NC for GL128S
A23
A22
A15
A14
A13
A12
A11
A10
A9
A8
A19
A20
WE#
RESET#
A21
WP#
RY/BY#
A18
A17
A7
A6
A5
A4
A3
A2
A1
RFU
DNU
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
56-Pin TSOP
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
A24
A25
A16
RFU
VSS
DQ15
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
OE#
VSS
CE#
A0
RFU
VIO
NC for GL256S, GL128S
NC for GL512S, GL256S, GL128S
Notes:
1. Pin 28, Do Not Use (DNU), a device internal signal is connected to the package connector. The connector may be used by Spansion for
test or other purposes and is not intended for connection to any host system signal. Do not use these connections for PCB Signal routing
channels. Though not recommended, the ball can be connected to VCC or VSS through a series resistor.
2. Pin 27, 30, and 53 Reserved for Future Use (RFU).
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
91
D at a
11.1.2
S hee t
Physical Diagram
Figure 11.2 56-Pin Thin Small Outline Package (TSOP), 14 x 20 mm
PACKAGE
SYMBOL
MO-142 (B) EC
MIN.
NOM.
MAX.
1
CONTROLLING DIMENSIONS ARE IN MILLIMETERS (mm).
(DIMENSIONING AND TOLERANCING CONFORMS TO ANSI Y14.5M-1982.)
A
---
---
1.20
2
PIN 1 IDENTIFIER FOR STANDARD PIN OUT (DIE UP).
A1
0.05
---
0.15
3
A2
0.95
1.00
1.05
b1
0.17
0.20
0.23
TO BE DETERMINED AT THE SEATING PLANE -C- . THE SEATING PLANE IS
DEFINED AS THE PLANE OF CONTACT THAT IS MADE WHEN THE PACKAGE
LEADS ARE ALLOWED TO REST FREELY ON A FLAT HORIZONTAL SURFACE.
b
c1
0.17
0.10
0.22
---
0.27
0.16
4
DIMENSIONS D1 AND E DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE
MOLD PROTUSION IS 0.15 mm PER SIDE.
5
c
0.10
---
0.21
DIMENSION b DOES NOT INCLUDE DAMBAR PROTUSION. ALLOWABLE
DAMBAR PROTUSION SHALL BE 0.08 mm TOTAL IN EXCESS OF b
DIMENSION AT MAX MATERIAL CONDITION. MINIMUM SPACE BETWEEN
PROTRUSION AND AN ADJACENT LEAD TO BE 0.07 mm.
6
THESE DIMESIONS APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN
0.10 mm AND 0.25 mm FROM THE LEAD TIP.
7
LEAD COPLANARITY SHALL BE WITHIN 0.10 mm AS MEASURED FROM THE
SEATING PLANE.
8
DIMENSION "e" IS MEASURED AT THE CENTERLINE OF THE LEADS.
D
19.80
20.00
20.20
D1
18.30
18.40
18.50
E
13.90
14.00
14.10
e
L
0.50 BASIC
0.50
0.60
0.70
O
0˚
-
8˚
R
0.08
---
0.20
N
92
NOTES:
TS 56
JEDEC
56
3160\38.10A
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
11.2
She et
64-Ball FBGA
11.2.1
Connection Diagram
Figure 11.3 64-ball Fortified Ball Grid Array
TOP VIEW
PRODUCT Pinout
A
B
C
D
E
F
G
H
NC for GL256S, GL128S
-
NC for GL128S
NC for GL512S, GL256S, GL128S
8
NC
A22
A23
Vio
VSS
A24
A25
NC
7
A13
A12
A14
A15
A16
RFU
DQ15
VSS
6
A9
A8
A10
A11
DQ7
DQ14
DQ13
DQ6
5
WE#
RESET#
A21
A19
DQ5
DQ12
VCC
DQ4
4
RY/BY#
WP#
A18
A20
DQ2
DQ10
DQ11
DQ3
3
A7
A17
A6
A5
DQ0
DQ8
DQ9
DQ1
2
A3
A4
A2
A1
A0
CE#
OE#
VSS
1
NC
NC
NC
NC
DNU
Vio
RFU
NC
Notes:
1. Ball E1, Do Not Use (DNU), a device internal signal is connected to the package connector. The connector may be used by Spansion for
test or other purposes and is not intended for connection to any host system signal. Do not use these connections for PCB Signal routing
channels. Though not recommended, the ball can be connected to VCC or VSS through a series resistor.
2. Balls F7 and G1, Reserved for Future Use (RFU).
3. Balls A1, A8, C1, D1, H1, and H8, No Connect (NC).
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
93
D at a
11.2.2
S hee t
Physical Diagram – LAE064
Figure 11.4 LAE064—64-ball Fortified Ball Grid Array (FBGA), 9 x 9 mm
NOTES:
PACKAGE
LAE 064
JEDEC
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994.
N/A
2. ALL DIMENSIONS ARE IN MILLIMETERS.
9.00 mm x 9.00 mm
PACKAGE
3. BALL POSITION DESIGNATION PER JESD 95-1, SPP-010?
EXCEPT AS NOTED).
SYMBOL
MIN
NOM
MAX
NOTE
A
---
---
1.40
A1
0.40
---
---
STANDOFF
A2
0.60
---
---
BODY THICKNESS
PROFILE HEIGHT
D
9.00 BSC.
BODY SIZE
E
9.00 BSC.
BODY SIZE
D1
7.00 BSC.
MATRIX FOOTPRINT
E1
7.00 BSC.
MATRIX FOOTPRINT
MD
8
MATRIX SIZE D DIRECTION
ME
8
MATRIX SIZE E DIRECTION
N
64
BALL COUNT
b
0.50
0.60
0.70
BALL DIAMETER
eD
1.00 BSC.
BALL PITCH - D DIRECTION
eE
1.00 BSC.
BALL PITCH - E DIRECTION
SD / SE
0.50 BSC.
?
NONE
SOLDER BALL PLACEMENT
DEPOPULATED SOLDER BALLS
4.
e REPRESENTS THE SOLDER BALL GRID PITCH.
5. SYMBOL "MD" IS THE BALL ROW MATRIX SIZE IN THE
"D" DIRECTION.
SYMBOL "ME" IS THE BALL COLUMN MATRIX SIZE IN THE
"E" DIRECTION.
N IS THE TOTAL NUMBER OF SOLDER BALLS.
6
DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL
DIAMETER IN A PLANE PARALLEL TO DATUM C.
7
SD AND SE ARE MEASURED WITH RESPECT TO DATUMS
A AND B AND DEFINE THE POSITION OF THE CENTER
SOLDER BALL IN THE OUTER ROW.
WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN ?
THE OUTER ROW PARALLEL TO THE D OR E DIMENSION,
RESPECTIVELY, SD OR SE = 0.000.
WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN
THE OUTER ROW, SD OR SE = e/2
8. NOT USED.
9. "+" INDICATES THE THEORETICAL CENTER OF
DEPOPULATED BALLS.
3623 \ 16-038.12 \ 1.16.07
94
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
11.2.3
She et
Physical Diagram – LAA064
NOTES:
PACKAGE
LAA 064
JEDEC
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994.
N/A
2. ALL DIMENSIONS ARE IN MILLIMETERS.
13.00 mm x 11.00 mm
PACKAGE
3. BALL POSITION DESIGNATION PER JESD 95-1, SPP-010 (EXCEPT
AS NOTED).
SYMBOL
MIN
NOM
MAX
NOTE
A
---
---
1.40
A1
0.40
---
---
STANDOFF
A2
0.60
---
---
BODY THICKNESS
PROFILE HEIGHT
D
13.00 BSC.
BODY SIZE
E
11.00 BSC.
BODY SIZE
D1
7.00 BSC.
MATRIX FOOTPRINT
E1
7.00 BSC.
MD
8
MATRIX SIZE D DIRECTION
ME
8
MATRIX SIZE E DIRECTION
N
64
φb
0.50
0.60
MATRIX FOOTPRINT
BALL COUNT
0.70
BALL DIAMETER
eD
1.00 BSC.
BALL PITCH - D DIRECTION
eE
1.00 BSC.
BALL PITCH - E DIRECTION
SD / SE
0.50 BSC.
SOLDER BALL PLACEMENT
NONE
DEPOPULATED SOLDER BALLS
4.
e REPRESENTS THE SOLDER BALL GRID PITCH.
5. SYMBOL "MD" IS THE BALL ROW MATRIX SIZE IN THE
"D" DIRECTION.
SYMBOL "ME" IS THE BALL COLUMN MATRIX SIZE IN THE
"E" DIRECTION.
N IS THE TOTAL NUMBER OF SOLDER BALLS.
6
DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL
DIAMETER IN A PLANE PARALLEL TO DATUM C.
7
SD AND SE ARE MEASURED WITH RESPECT TO DATUMS
A AND B AND DEFINE THE POSITION OF THE CENTER
SOLDER BALL IN THE OUTER ROW.
WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN
THE OUTER ROW PARALLEL TO THE D OR E DIMENSION,
RESPECTIVELY, SD OR SE = 0.000.
WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN
THE OUTER ROW, SD OR SE = e/2
8. NOT USED.
9. "+" INDICATES THE THEORETICAL CENTER OF DEPOPULATED
BALLS.
3354 \ 16-038.12d
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
95
D at a
11.3
S hee t
56-Ball FBGA
11.3.1
Connection Diagram
Figure 11.5 56-ball Fortified Ball Grid Array
TOP VIEW
Product Pinout
A
B
C
D
512 Mb & 256 Mb Only
8
E
F
G
H
512 Mb Only
Supports WP# only,
not WP#/ACC
A15
A21
A22
A16
RFU/A24
VSS
A11
A12
A13
A14
RFU
DQ15
DQ7
DQ14
A8
A19
A9
A10
DQ6
DQ13
DQ12
DQ5
WE#
RFU/A23
A20
DQ4
VIO
RFU
WP#
RESET# RY/BY#
DQ3
VCC
DQ11
7
6
5
4
3
NC
NC
A18
A17
DQ1
DQ9
DQ10
DQ2
A7
A6
A5
A4
VSS
OE#
DQ0
DQ8
A3
A2
A1
A0
CE#
DNU
2
1
Notes:
1. Ball G1, Do Not Use (DNU), a device internal signal is connected to the package connector. The connector may be used by Spansion® for
test or other purposes and is not intended for connection to any host system signal. Do not use these connections for PCB Signal routing
channels. Though not recommended, the ball can be connected to VCC or VSS through a series resistor.
2. Balls E7, F8, and H5, Reserved for Future Use (RFU).
3. Balls A3 and B3, No Connect (NC).
96
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
11.3.2
She et
Physical Diagram - VBU 056
A
D
D1
e
0.10 C
(2X)
8
7
SE 7
6
5
E
E1
4
3
e
2
1
9
H
A1 CORNER
INDEX MARK
B
TOP VIEW
G
F
E
D
C
B
A
A1 CORNER
6
SD
56 b
0.10 C
7
0.08 M C
0.15 M C A B
(2X)
BOTTOM VIEW
0.10 C
A
A1
SEATING PLANE
C
0.08 C
SIDE VIEW
NOTES:
PACKAGE
VBU 056
JEDEC
1. DIMENSIONING AND TOLERANCING METHODS PER
ASME Y14.5M-1994.
N/A
2. ALL DIMENSIONS ARE IN MILLIMETERS.
9.00 mm x 7.00 mm NOM
PACKAGE
SYMBOL
MIN
NOM
MAX
A
---
---
1.00
A1
0.17
---
---
NOTE
4.
BALL HEIGHT
5. SYMBOL "MD" IS THE BALL MATRIX SIZE IN THE
"D" DIRECTION.
D
9.00 BSC.
BODY SIZE
E
7.00 BSC.
BODY SIZE
D1
5.60 BSC.
BALL FOOTPRINT
BALL FOOTPRINT
E1
5.60 BSC.
MD
8
ROW MATRIX SIZE D DIRECTION
ME
8
ROW MATRIX SIZE E DIRECTION
N
b
56
0.35
0.40
TOTAL BALL COUNT
0.45
e
0.80 BSC.
BALL PITCH
0.40 BSC.
SOLDER BALL PLACEMENT
e REPRESENTS THE SOLDER BALL GRID PITCH.
SYMBOL "ME" IS THE BALL MATRIX SIZE IN THE
"E" DIRECTION.
N IS THE TOTAL NUMBER OF POPULATED SOLDER
BALL POSITIONS FOR MATRIX SIZE MD X ME.
6
DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL
DIAMETER IN A PLANE PARALLEL TO DATUM C.
7
SD AND SE ARE MEASURED WITH RESPECT TO DATUMS
A AND B AND DEFINE THE POSITION OF THE CENTER
SOLDER BALL IN THE OUTER ROW.
BALL DIAMETER
SD / SE
A1,A8,D4,D5,E4,E5,H1,H8
3. BALL POSITION DESIGNATION PER JEP95, SECTION
4.3, SPP-010.
OVERALL THICKNESS
WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN
THE OUTER ROW SD OR SE = 0.000.
WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN
THE OUTER ROW, SD OR SE = e/2
DEPOPULATED SOLDER BALLS
8. "+" INDICATES THE THEORETICAL CENTER OF
DEPOPULATED BALLS.
9
A1 CORNER TO BE IDENTIFIED BY CHAMFER, LASER OR INK
MARK, METALLIZED MARK INDENTATION OR OTHER MEANS.
10. OUTLINE AND DIMENSIONS PER CUSTOMER REQUIREMENT.
g1055\ 16-038.25 \ 01.26.12
12. Special Handling Instructions for FBGA Package
Special handling is required for Flash Memory products in FBGA packages.
Flash memory devices in FBGA packages may be damaged if exposed to ultrasonic cleaning methods. The
package and/or data integrity may be compromised if the package body is exposed to temperatures above
150°C for prolonged periods of time.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
97
D at a
S hee t
13. Ordering Information
Valid Combinations
Table 13.1 lists configurations planned to be available in volume. The table will be updated as new
combinations are released. Consult your local sales representative to confirm availability of specific
combinations and to check on newly released combinations.
Table 13.1 S29GL-S Valid Combinations (Sheet 1 of 2)
S29GL-S Valid Combinations
Base OPN
Speed (ns)
100
Package and Temperature
DHI, FHI, TFI
(Note 1)
DHV, TFV
(Note 1)
S29GL01GS
Model Number
(Note 1)
120
DHV, TFV (Note 1)
Ordering Part Number
(yy = Model Number, x =
Packing Type)
S29GL01GS10DHIyyx
01, 02
S29GL01GS10FHIyyx
S29GL01GS10TFIyyx
S29GL01GS11DHVyyx
01, 02
110
DHI, FHI, TFI
Packing
Type
0, 3
S29GL01GS11TFVyyx
(Note 2)
S29GL01GS11DHIyyx
V1, V2
S29GL01GS11FHIyyx
S29GL01GS11TFIyyx
S29GL01GS12DHVyyxx
V1, V2
S29GL01GS12TFVyyxx
S29GL512S10DHIyyx
100
DHI, FHI, GHI, TFI
(Note 1)
S29GL512S10FHIyyx
01, 02
S29GL512S10GHIyyx
S29GL512S10TFIyyx
DHV, TFV
(Note 1)
S29GL512S
01, 02
S29GL512S11DHVyyx
0, 3
S29GL512S11TFVyyx
(Note 2)
110
S29GL512S11DHIyyx
DHI, FHI, TFI (Note 1)
V1, V2
S29GL512S11FHIyyx
S29GL512S11TFIyyx
120
DHV, TFV (Note 1)
S29GL512S12DHVyyxx
V1, V2
S29GL512S12TFVyyxx
S29GL256S90DHIyyx
90
DHI, FHI, GHI, TFI
(Note 1)
S29GL256S90FHIyyx
01, 02
S29GL256S90GHIyyx
S29GL256S90TFIyyx
DHV, TFV
(Note 1)
S29GL256S
01, 02
DHI, FHI, TFI
(Note 1)
98
S29GL256S10TFVyyx
(Note 2)
100
110
S29GL256S10DHVyyx
0, 3
DHV, TFV (Note 1)
GL-S MirrorBit® Family
S29GL256S10DHIyyx
V1, V2
S29GL256S10FHIyyx
S29GL256S10TFIyyx
V1, V2
S29GL256S11DHVyyxx
S29GL256S11TFVyyxx
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Table 13.1 S29GL-S Valid Combinations (Sheet 2 of 2)
S29GL-S Valid Combinations
Base OPN
Speed (ns)
Package and Temperature
Model Number
Packing
Type
Ordering Part Number
(yy = Model Number, x =
Packing Type)
S29GL128S90DHIyyx
90
DHI, FHI, GHI, TFI
(Note 1)
S29GL128S90FHIyyx
01, 02
S29GL128S90GHIyyx
S29GL128S90TFIyyx
DHV, TFV
(Note 1)
S29GL128S
01, 02
0, 3
S29GL128S10TFVyyx
(Note 2)
100
DHI, FHI, TFI
(Note 1)
110
S29GL128S10DHVyyx
DHV, TFV (Note 1)
S29GL128S10DHIyyx
V1, V2
S29GL128S10FHIyyx
S29GL128S10TFIyyx
V1, V2
S29GL128S11DHVyyxx
S29GL128S11TFVyyxx
Notes:
1. Additional speed, package, and temperature options maybe offered in the future. Check with your local sales representative for
availability.
2. Package Type 0 is standard option.
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
99
D at a
S hee t
The ordering part number for the General Market device is formed by a valid combination of the following:
S29GL01GS
10
D
H
I
01
0
Packing Type
0 = Tray
3 = 13” Tape and Reel
Model Number (VIO and VCC Range)
01 = VIO = VCC = 2.7 to 3.6V, highest address sector protected
02 = VIO = VCC = 2.7 to 3.6V, lowest address sector protected
V1 = VIO = 1.65 to VCC, VCC = 2.7 to 3.6V, highest address sector protected
V2 = VIO = 1.65 to VCC, VCC = 2.7 to 3.6V, lowest address sector protected
Temperature Range
I = Industrial (-40°C to +85°C)
V = In Cabin (-40°C to +105°C)
Package Materials Set
F = Lead Free (Pb-Free)
H = Low Halogen, Pb-Free
Package Type
D = Fortified Ball-Grid Array Package (LAE064) 9 mm x 9 mm
F = Fortified Ball-Grid Array Package (LAA064) 13 mm x 11 mm
G = Fortified Ball-Grid Array Package (VBU056) 9 mm x 7 mm
T = Thin Small Outline Package (TSOP) Standard Pinout
Speed Option
90 = 90 ns random access time
10 = 100 ns random access time
11 = 110 ns random access time
12 = 120 ns random access time
Device Number/Description
S29GL01GS, S29GL512S, S29GL256S, S29GL128S
3.0 Volt Core, with VIO Option, 1024, 512, 256, 128 Megabit Page-Mode Flash Memory,
Manufactured on 65 nm MirrorBit Eclipse Process Technology
100
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
14. Other Resources
Visit www.spansion.com to obtain the following related documents:
14.1
Links to Software
Downloads and related information on flash device support is available at
http://www.spansion.com/Support/Pages/DriversSoftware.aspx
 Spansion low-level drivers
 Enhanced flash drivers
 Flash file system
Downloads and related information on simulation modeling and CAD modeling support is available at
http://www.spansion.com/Support/Pages/SimulationModels.aspx
 VHDL and Verilog
 IBIS
 ORCAD
14.2
Links to Application Notes
The following is a sample list of application notes related to this product. All Spansion application notes are
available at http://www.spansion.com/Support/TechnicalDocuments/Pages/ApplicationNotes.aspx
 Common Flash Interface Version 1.5 Vendor Specific Extensions
 Common Flash Memory Interface Specification
 Connecting Unused Data Lines of MirrorBit Flash
 Developing System-Level Validation Routines
 Flash Memory: An Overview
 Interfacing i.MX3x to S29GL MirrorBit NOR Flash
 Interfacing the S29GL-S to Freescale Coldfire Processor
 Interfacing Spansion GL MirrorBit Family to Freescale i.MX31 Processors
 MirrorBit Flash Memory Write Buffer Programming and Page Buffer Read
 Optimizing Program/Erase Times
 Practical Guide to Endurance and Data Retention
 Programmer’s Guide for the Spansion 65 nm GL-S Eclipse Family Architecture
 Reset Voltage and Timing Requirements for MirrorBit Flash
 Signal Integrity and Reliable Flash Operations
 Understanding AC Characteristics
 Understanding Load Capacitance and Access Time
 Understanding Page Mode Flash Memory Devices
 Using CFI to Read and Debug Systems
 Versatile IO: DQ and Enhanced
 Wear Leveling
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
101
D at a
14.3
S hee t
Specification Bulletins
Contact your local sales office for details.
14.4
Contacting Spansion
Obtain the latest list of company locations and contact information on our web site at
http://www.spansion.com/About/Pages/Locations.aspx
102
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
15. Revision History
Section
Description
Revision 01 (February 11, 2011)
Initial release
Revision 02 (March 21, 2011)
Global
OPN
Command Definitions Table
Physical Interface
Modified document from “Advance Information” to “Preliminary”
Added FBGA package offering for V1 & V2 Model Number
Removed KGD information, which is documented in a separate Supplement
Removed duplicated commands
Changed the number of command cycles for a CFI Enter from 3 to 1
Updated 56-pin TSOP pinout figure
Updated 64-ball FBGA pinout figure
Other Resources
Added additional application notes in “Links to Application Notes”
Lock Register Table
Changed the default value of bit 7 in the Lock register
Revision 03 (July 8, 2011)
Performance Summary
Updated table: Typical Program and Erase Rates
Secure Silicon Region ASO
Corrected table: Secure Silicon Region
DQ1: Write-to-Buffer Abort
Corrected table: Data Polling Staus
Embedded Algorithm Performance
Table
Updated table: Embedded Algorithm Characteristics
Corrected tables: changed Software Reset/ASO Exit Data value to from 00F0h to xF0h
Corrected table: Erase Suspend Unlock State Command Transition
Corrected table: Erase Suspend - DYB State Command Transition
Corrected table: Program Unlock State Command Transition
Command State Transitions
Corrected table: Lock Register State Command Transition
Corrected table: Secure Silicon Sector Program State Command Transition
Corrected table: Password Protection Command State Transition
Corrected table: Non-Volatile Protection Command State Transition
Corrected table: PPB Lock Bit Command State Transition
Corrected table: Volatile Sector Protection Command State Transition
Device ID and Common Flash Interface
(ID-CFI) ASO Map
DC Characteristics
Power-On Reset (POR) and Warm
Reset
Power-On (Cold) Reset (POR)
Hardware (Warm) Reset
Asynchronous Write Operations
Physical Diagram - LAA064
Corrected table: Corrected CFI Primary Vendor-Specific Extended Query description for Word
Address (SA) + 0045h
Updated VIL Max
Updated Note
Updated table: added row to bottom of table
Updated text
Updated figure: Power-Up Diagram
Updated figure: Hardware Reset
Added figure: Back to Back (CE#VIL) Write Operation Timing Diagram
Updated table: Erase/Program Operations
Added figure
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
103
D at a
S hee t
Section
Description
Revision 04 (October 3, 2011)
Power-Up Write Inhibit
Minor correction
PPB Password Protection Mode
Minor correction
Embedded Algorithm Characteristics
table
Updated Buffer Programming Time maximum limits
Absolute Maximum Ratings table
Added clarification
DC Characteristics table
Output High Voltage clarification
Power-Up/Power-Down Voltage and
Timing table
Added clarification
Power-Up figure
Added clarification
Power-On (Cold) Reset (POR)
Added clarification
Valid Combinations table
Updated table
Revision 05 (December 14, 2011)
Global
Data sheet designation changed from Preliminary to Full Production
Sector Erase: Updated Typical Erase Time
Capacitance Characteristics
Updated section
Ordering Information
Corrected note designation in valid combination table
Revision 06 (March 16, 2012)
Global
Ordering Information
Added 9 mm x 7 mm package
Added 105°C offering
Updated Valid Combinations
Revision 07 (December 21, 2012)
Distinctive Characteristics
Added In-Cabin temperature range
Status Register ASO
Added clarification
Advanced Sector Protection Overview
Updated figure
PPB Lock
Added clarification
Persistent Protection Bits (PPB)
Added clarification
Dynamic Protection Bits (DYB)
Added clarification
PPB Password Protection Mode
Added clarification
Chip Erase
Added clarification
Sector Erase
Added clarification
Erase Suspend / Erase Resume
Added clarification
Status Register ASO
Added clarification
Status Register
Added clarification
DQ7: Data# Polling
Added clarification
DQ1: Write-to-Buffer Abort
Embedded Operation Error
Added clarification
Data Polling Status: Updated table
Added clarification
Protection Error
Added clarification
Write Buffer Abort
Added clarification
Performance Table
Updated Embedded Algorithm Characteristics (-40°C to +105°C) table
Device ID and Common Flash Interface
(ID-CFI) ASO Map
Updated CFI Device Geometry Definition table
Asynchronous Read Operations
Added Read Operation VIO = 1.65 (-40°C to +105°C) table
Asynchronous Write Operations
104
Updated CFI Primary Vendor-Specific Extended Query table
Updated Read to Write (CE# VIL) figure
Updated Read to Write (CE# Toggle) figure
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013
Data
She et
Section
Description
Revision 08 (October 9, 2013)
S29GL-S Valid Combinations Table
Added VIO Models for Automotive In Cabin Temperature Range
October 9, 2013 S29GL_128S_01GS_00_08
GL-S MirrorBit® Family
105
D at a
S hee t
Colophon
The products described in this document are designed, developed and manufactured as contemplated for general use, including without
limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as
contemplated (1) for any use that includes fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the
public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility,
aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for
any use where chance of failure is intolerable (i.e., submersible repeater and artificial satellite). Please note that Spansion will not be liable to
you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor
devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design
measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal
operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under
the Foreign Exchange and Foreign Trade Law of Japan, the US Export Administration Regulations or the applicable laws of any other country,
the prior authorization by the respective government entity will be required for export of those products.
Trademarks and Notice
The contents of this document are subject to change without notice. This document may contain information on a Spansion product under
development by Spansion. Spansion reserves the right to change or discontinue work on any product without notice. The information in this
document is provided as is without warranty or guarantee of any kind as to its accuracy, completeness, operability, fitness for particular purpose,
merchantability, non-infringement of third-party rights, or any other warranty, express, implied, or statutory. Spansion assumes no liability for any
damages of any kind arising out of the use of the information in this document.
Copyright © 2011-2013 Spansion Inc. All rights reserved. Spansion®, the Spansion logo, MirrorBit®, MirrorBit® Eclipse™, ORNAND™ and
combinations thereof, are trademarks and registered trademarks of Spansion LLC in the United States and other countries. Other names used
are for informational purposes only and may be trademarks of their respective owners.
106
GL-S MirrorBit® Family
S29GL_128S_01GS_00_08 October 9, 2013