SHOULDER SPECIFICATION Item: Type: CRYSTAL SMD0503 Optional SHOULDER SMD0503 CRYSTAL Scope This specification shall cover the characteristics of SMD 5x3.2 crystal. Ultra small package Wide Frequency Range Electrical Specification Parameter Value Nominal Frequency 10.00 to 80.000 MHz Frequency Tolerance (at 25°C) + 30 PPM (Maximum) Frequency Stability +30 PPM (Maximum) Oscilation Mode Fundamental Equivalent Series resistance 50Ω Drive Level 1.0 mW (Maximum) Operating Temperature Range -20 to + 70ºC Standard (or Optional) Storage Temperature -40 to + 85ºC Load Capacitance 10 pF to Series Shunt Capacitance < 7 PF Aging (at 25°C) + 3 ppM per year Insulation Resistance > 500 MΩ at DC 100V Mechanical Dimensions (All in mm) SMD0503 SHOULDER INDÚSTRIA ELETRÔNICA LTDA Rua Vereador Antonio Zamarioni, 105 (Portal de Extrema) CEP 37640-000 Extrema / MG www.hdshoulder.com.br Page 2 of 5 SHOULDER SMD0503 CRYSTAL Mechanical Specification Conditions Results 1. Vibration test Frequency Amplitude Sweep Duration 10 ~ 55Hz 0.762mm 1.0 minute 2 hours Frequency and wave form of tested products must remain within specifications. Method of drop Dropping floor Height Number of drops Natural drop Hard wood board 30cm 3 times Frequency and wave form of tested products must remain within specifications. 2. Drop test Environmental Specification Conditions Results 1. Temperature test 1) at -55°C, 30 minutes 2) at +25°C, 10~15 minutes Steps of cycle Temperature cycling test 3) at +85°C, 30 minutes 4) at +25°C, 10~15 minutes Number of cycles 3 times 2. Aging test Temperature +85°C ±20°C Length of test 96 hours 3. Salt spray test Temperature +35°C ±2°C Length of test 48 hours NaCI % 5% 4. Humidity test Temperature +40°C ±2°C Relative humidity 90 ~ 95% Length of test 96 hours Frequency and wave form of tested products must remain within specifications. Deviation of frequency must be less than ±3ppM. There should be no stain on surface of products. a) Insulation resistance must be 500 MΩ/100 Vac minimum. b) Resistance and wave form must remain within specifications. Soldering SHOULDER INDÚSTRIA ELETRÔNICA LTDA Rua Vereador Antonio Zamarioni, 105 (Portal de Extrema) CEP 37640-000 Extrema / MG www.hdshoulder.com.br Page 3 of 5 SHOULDER SMD0503 CRYSTAL Tape Specifications (All in mm) Reeling Quantity - 1000pcs / reel Carrier Tape Dimensions W 16+ 0.3 F 5.5+ 0.05 P0 4.0+ 0.1 P1 9.0+ 0.1 D0 ∅1.5+ 0.1 D1 ∅1.6 + 0.25 t1 0.3+ 0.03 t2 1.7+ 0.1 A 4.2+ 0.1 B 6+ 0.1 SMD0503 CRYSTAL Part Numbering System (Example) SHOULDER INDÚSTRIA ELETRÔNICA LTDA Rua Vereador Antonio Zamarioni, 105 (Portal de Extrema) CEP 37640-000 Extrema / MG www.hdshoulder.com.br Page 4 of 5 SHOULDER SMD0503 CRYSTAL SMD0503 11.0592 F 20 30 30 A T Type Nominal Frequency (in MHz) Vibration Mode Load Capacitance Frequency Tolerance Frequency Stability Operating Temperature Range Option (can be blank) SMD0503 49S-SMD 49S2-SMD SMD0804 SMD0705 SMD0603 SMD0402 Enter the nominal frequency (3 digits after dot) or up to last significant digit (different than zero) S = Series F = Fund Or enter load capacitance: 10 to 33 for parallel Indicate the tolerance value in ± PPM Indicate the stability over temperature range value in ± PPM SHOULDER INDÚSTRIA ELETRÔNICA LTDA Rua Vereador Antonio Zamarioni, 105 (Portal de Extrema) CEP 37640-000 Extrema / MG www.hdshoulder.com.br A -20°C to 70°C B -10°C to 60°C C 0°C to 50°C D -30°C to 80°C E -40°C to 85°C S= Standard X= Additional Specifications T= Tape and Reel Page 5 of 5