THICK FILM CONVEX CHIP ARRAYS SMN SERIES Resistor Arrays ZMN SERIES Jumper Arrays Term.W is RoHS compliant & 260°C compatible RoHS Internationally popular convex termination pads Industry’s widest selection and lowest cost! 1Ω to 10MΩ, 0.5% to 5%, 8 sizes, 3 circuit schematics 2 to 9 resistors per array reduces mounting costs ZMN Series zero ohm jumpers are 1Amp, 50mΩ max Scalloped edge design available RCD’s Series SMN resistor and ZMN jumper chip arrays not only enable significant pcb space savings, but a sizeable cost savings over the use of individual components. The savings in assembly cost, by placing a single chip instead of multiple chips, more than pays for the cost of these components. SMN/ZMN feature convex terminations, concave avaliable (see CN Series). 4 PIN: SMN0404, SMN0606 → P ← ↓ T --↑ ↑ W --↓ ← L→ → H← RESISTORSCAPACITORSCOILSDELAY LINES 10 PIN: SMN2010, SMNN1206 (SMNN1206 avial. in Config. D only) ↓ W Config. A ↑ W ↓ → P ← L ↓ ↑ SMN0404 SMN0606 SMN0804 SMN1206 SMNN1206 SMN1506 SMN2010 SMN2010 SMN2012 SMN2012 A A A A D A A B A B** ↑ L 1 Rated Pow er* 62mW 62mW 62mW 62mW 31mW 62mW*** 100mW 55mW 125mW 62mW Config. A Working Voltage 25V 50V 25V 50V 25V 25V 50V 50V 50V 50V * Rated power is per resistor element at 70°C 50 25 0 25 50 Config. B TC (ppm/°C) 250ppm 200ppm 250ppm 200ppm 200ppm 200ppm 200ppm 200ppm 200ppm 200ppm Res. Range Res. Range Res. Range 0.5% Tol 1% Tol 2 & 5% Tol ** ** 10Ω - 1M ** ** 1Ω - 10M ** ** 10Ω - 1M 22Ω-470K 1Ω - 10M 1Ω - 10M ** ** 10Ω - 1M ** ** 10Ω - 1M ** ** 10Ω - 1M ** ** 10Ω - 1M ** 22Ω - 1M 10Ω - 1M ** ** 10Ω - 1M 123 123 123 123 ↑ D ↓ 123 123 ↑ 123 C 123 123 ↓ 75 100 125 150 175 200 70 AMBIENT TEMPERATURE (°C) 12 12 12 12 12 12 12 12 12 123 123 123 123 123 123 123 123 123 A← → → TYPICAL PERFORMANCE CHARACTERISTICS Operating Temp. Range -55°C to +150°C Short time Overload (2.5X rated W, 5 sec) ±2%+0.1Ω max. Resistance to Solder Heat (260°C, 10 sec) ±1%+0.1Ω max. Moisture Res. (90-95% RH, 40°C,100 hrs) ±3%+0.1Ω max. High Temp. Exposure (125°C, 100 hrs) ±1%+0.1Ω max. Load Life (1000 hrs at rated W) ±3%+0.1Ω max. Insulation Resistance 10,000 Megohm Dielectric Withstanding Voltage ↓ L ±.01 [.25] .039 [1] .063 [1.6] .079 [2] .126 [3.2] .126 [3.2] .154 [3.9] .200 [5.08] .200 [5.08] .200 [5.08] .200 [5.08] 1 Config. A ↓ --- W → P← L SUGGESTED LAYOUT 123 12 PAD 123 123 123 ----------- % OF 70°C RATING 75 1 1 ↑ Config. B 1 Config. D T --1 → H← W±.008 [.2] .039 [1] .063 [1.6] .039 [1] .063 [1.6] .063 [1.6] .063 [1.6] .100 [2.54] .100 [2.54] .122 [3.10] .122 [3.10] Config. A P±.008 [.2] .025 [.65] .0315 [.8] .02 [.5] .0315 [.8] .025 [.64] .02 [.5] .040 [1.0] .040 [1.0] .050 [1.27] .050 [1.27] H±.006 [.15] .016 [.4] .022 [.55] .016 [.4] .022 [.55] .022 [.55] .018 [.45] .024 [.6] .024 [.6] .024[ .6] .024 [.6] T typ. .010 [.25] .012 [.3] .010 [.25] .010 [.25] .010 [.25] .012 [.3] .010 [.25] .010 [.25] .012 [.30] .012 [.30] ** Consult factory for availability *** SMN1506 package power rating is .25W DERATING 100 --- 16 PIN: SMN1506 --- Config T ↑ →H← T → H← RCD Type ↓ → P← L 1 8 PIN: SMN0804, SMN1206, SMN2012 --- --- ↑ 400V 123 123 123 123 123 123 123 123 123 B← 123 123 123 123 123 123 123 123 123 RCD Type SMN0404 (4-pin) SMN0606 (4-pin) SMN0804 (8-pin) SMN1206 (8-pin) SMNN1206 (10-pin) SMN1506 (16-pin) SMN2010 (10-pin) S MN2012 (8-pin) P/N DESIGNATION: A .014 [.36] .016 [.4] .012 [.3] .018 [.45] .014 [.36] .012 [.3] .022 [.55] .032 [.82] B C D .011 [.28] .020 [.5] .020 [.5] .016 [.4] .032 [.8] .036 [.9] .008 [.2] .020 [.5] .020 [.5] .014 [.36] .032 [.8] .036 [.9] .011 [.28] .032 [.8] .036 [.9] .008 [.2] .032 [.8] .039 [1] .018 [.45] .040 [1] .060[1.5] .018 [.45] .045 [1.1] .080 [2] SMN 2010 A - 102 - J T W Type (SMN, SMNN or ZMN) Chip Size Circuit Configuration: A, B, D Resis.Code 1%: 3 signif. figures & multiplier, e.g. 1R00=1Ω, 10R0=10Ω, 1000=100Ω, 1001=1KΩ, etc. Resis.Code 2%-5%: 2 signif. figures & multiplier, e.g. 1R0=1Ω, 100=10Ω, 101=100Ω, 102=1KΩ, etc. Leave blank on ZMN zero-ohm jumper arrays (.05Ω max) Tolerance Code: J=5%(std), G=2%, F=1%, D=0.5% Leave blank on ZMN zero-ohm jumper arrays Packaging: B = Bulk, T = Tape & Reel Termination: W= Lead-free (standard), Q= Tin/Lead (leave blank if either is acceptable) RCD Components Inc, 520 E.Industrial Park Dr, Manchester, NH, USA 03109 rcdcomponents.com Tel: 603-669-0054 Fax: 603-669-5455 Email:[email protected] FA075A Sale of this product is in accordance with GF-061. Specifications subject to change without notice. 32