SN54ABT534, SN74ABT534A OCTAL EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH 3-STATE OUTPUTS SCBS187F – JANUARY 1991 – REVISED JANUARY 1997 D D D D SN54ABT534 . . . J OR W PACKAGE SN74ABT534A . . . DB, DW, N, OR PW PACKAGE (TOP VIEW) OE 1Q 1D 2D 2Q 3Q 3D 4D 4Q GND 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 SN54ABT534 . . . FK PACKAGE (TOP VIEW) description These 8-bit flip-flops with 3-state outputs are designed specifically for driving highly capacitive or relatively low-impedance loads. They are particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers. VCC 8Q 8D 7D 7Q 6Q 6D 5D 5Q CLK 2D 2Q 3Q 3D 4D 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 8D 7D 7Q 6Q 6D 4Q GND CLK 5Q 5D The eight flip-flops are edge-triggered D-type flip-flops. On the positive transition of the clock (CLK), the Q outputs are set to the complement of the logic levels set up at the data (D) inputs. 8Q D State-of-the-Art EPIC-ΙΙB BiCMOS Design Significantly Reduces Power Dissipation Latch-Up Performance Exceeds 500 mA Per JEDEC Standard JESD-17 Typical VOLP (Output Ground Bounce) < 1 V at VCC = 5 V, TA = 25°C High-Drive Outputs (–32-mA IOH, 64-mA IOL) ESD Protection Exceeds 2000 V Per MIL-STD-883, Method 3015; Exceeds 200 V Using Machine Model (C = 200 pF, R = 0) Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline (DB), and Thin Shrink Small-Outline (PW) Packages, Ceramic Chip Carriers (FK), Plastic (N) and Ceramic (J) DIPs, and Ceramic Flat (W) Package 1D 1Q OE VCC D A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high or low logic levels) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines without need for interface or pullup components. OE does not affect the internal operations of the flip-flop. Previously stored data can be retained or new data can be entered while the outputs are in the high-impedance state. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. The SN54ABT534 is characterized for operation over the full military temperature range of –55°C to 125°C. The SN74ABT534A is characterized for operation from –40°C to 85°C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. EPIC-ΙΙB is a trademark of Texas Instruments Incorporated. Copyright 1997, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN54ABT534, SN74ABT534A OCTAL EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH 3-STATE OUTPUTS SCBS187F – JANUARY 1991 – REVISED JANUARY 1997 FUNCTION TABLE (each flip-flop) INPUTS CLK D L ↑ H L L ↑ L H L H or L X Q0 H X X Z logic symbol† 1 OE CLK 1D 2D 3D 4D 5D 6D 7D 8D 11 3 OUTPUT Q OE logic diagram (positive logic) OE 1 EN CLK C1 1D 2 4 5 7 6 8 9 13 12 14 15 17 16 18 19 11 C1 1Q 1D 3 2 1Q 1D 2Q 3Q 4Q To Seven Other Channels 5Q 6Q 7Q 8Q † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. absolute maximum ratings over operating free-air temperature range (unless otherwise noted)‡ Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Voltage range applied to any output in the high or power-off state, VO . . . . . . . . . . . . . . . . . . . –0.5 V to 5.5 V Current into any output in the low state, IO: SN54ABT534 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 mA SN74ABT534A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –18 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Package thermal impedance, θJA (see Note 2): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115°C/W DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C ‡ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with EIA/JEDEC Std JESD51, except for through-hole packages, which use a trace length of zero. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54ABT534, SN74ABT534A OCTAL EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH 3-STATE OUTPUTS SCBS187F – JANUARY 1991 – REVISED JANUARY 1997 recommended operating conditions (see Note 3) SN54ABT534 VCC VIH Supply voltage 4.5 VIL VI Low-level input voltage IOH IOL High-level output current ∆t/∆v Input transition rise or fall rate High-level input voltage SN74ABT534A MAX MIN MAX 5.5 4.5 5.5 2 2 0.8 Input voltage 0 Low-level output current Outputs enabled TA Operating free-air temperature NOTE 3: Unused inputs must be held high or low to prevent them from floating. –55 0 V V 0.8 VCC –24 UNIT VCC –32 V V mA 48 64 mA 5 5 ns/V 85 °C 125 –40 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK VOH TEST CONDITIONS VCC = 4.5 V, VCC = 4.5 V, II = –18 mA IOH = –3 mA VCC = 5 V, VCC = 4 4.5 5V VOL Vhys II IOZH IOZL Ioff ICEX IO§ VCC = 4 4.5 5V TA = 25°C TYP† MAX SN54ABT534 MIN –1.2 MAX SN74ABT534A MIN –1.2 MAX –1.2 2.5 2.5 2.5 IOH = –3 mA IOH = –24 mA 3 3 3 2 2 IOH = –32 mA IOL = 48 mA 2* IOL = 64 mA 0.55 100 VI = VCC or GND VO = 2.7 V VCC = 5.5 V, VCC = 0, VO = 0.5 V VI or VO ≤ 4.5 V VCC = 5.5 V, VCC = 5.5 V, VO = 5.5 V VO = 2.5 V ∆ICC¶ Ci VI = 2.5 V or 0.5 V VO = 2.5 V or 0.5 V ±1 10‡ –10‡ ±100 µA ±100 µA 50 –180‡ µA µA µA –100 Outputs high 1 250 250 250 µA Outputs low 24 30 30 30 mA Outputs disabled 0.5 250 250 250 µA 1.5 1.5 1.5 mA –50 50 –180‡ ±1 10‡ –10‡ 50 –180‡ –50 VCC = 5.5 V, One input at 3.4 V, Other inputs at VCC or GND V mV ±1 10‡ –10‡ Outputs high 5 5 V, V IO = 0, 0 VCC = 5.5 VI = VCC or GND V V 0.55 0.55* VCC = 5.5 V, VCC = 5.5 V, UNIT 2 0.55 ICC Co MIN –50 mA 3.5 pF 6.5 pF * On products compliant to MIL-PRF-38535, this parameter does not apply. † All typical values are at VCC = 5 V. ‡ This data sheet limit may vary among suppliers. § Not more than one output should be tested at a time, and the duration of the test should not exceed one second. ¶ This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN54ABT534, SN74ABT534A OCTAL EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH 3-STATE OUTPUTS SCBS187F – JANUARY 1991 – REVISED JANUARY 1997 timing requirements over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 1) SN54ABT534 VCC = 5 V, TA = 25°C MIN MIN MAX UNIT MAX fclock tw Clock frequency 125 125 MHz Pulse duration CLK high or low 3.5 3.5 ns tsu Setup time, data before CLK↑ High or low 1.6 1.6 ns th Hold time, data after CLK↑ High or low 1.6 1.6 ns timing requirements over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 1) SN74ABT534A VCC = 5 V, TA = 25°C MIN MIN MAX UNIT MAX fclock tw Clock frequency Pulse duration CLK high or low 3.5 125 3.5 ns tsu Setup time, data before CLK↑ High or low 1.6 1.6 ns High or low 2† 2† ns th Hold time, data after CLK↑ † This data sheet limit may vary among suppliers. 125 MHz switching characteristics over recommended ranges of supply voltage and operating free-air temperature, CL = 50 pF (unless otherwise noted) (see Figure 1) SN54ABT534 PARAMETER fmax tPLH tPHL tPZH tPZL tPHZ tPLZ 4 FROM (INPUT) TO (OUTPUT) CLK Q OE Q OE Q POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 VCC = 5 V, TA = 25°C MIN MAX MIN TYP 125 175 2.6 4.5 6.1 2.6 7 3.4 5.5 6.7 3.4 7.9 UNIT MAX 125 MHz 1 3.4 5.2 1 5.8 2.6 4 5.8 2.6 7 2.4 4.7 6.6 2.4 7.6 2.3 3.8 5.8 2.3 6.8 ns ns ns SN54ABT534, SN74ABT534A OCTAL EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH 3-STATE OUTPUTS SCBS187F – JANUARY 1991 – REVISED JANUARY 1997 switching characteristics over recommended ranges of supply voltage and operating free-air temperature, CL = 50 pF (unless otherwise noted) (see Figure 1) SN74ABT534A PARAMETER fmax tPLH tPHL tPZH tPZL tPHZ tPLZ FROM (INPUT) TO (OUTPUT) CLK Q OE Q OE Q POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 VCC = 5 V, TA = 25°C MIN MAX MIN TYP 125 175 2.6 4.5 5.9 2.6 6.7 3.4 5.5 6.7 3.4 7.6 UNIT MAX 125 MHz 1 3.4 4.2 1 5 2.6 4 5.8 2.6 6.8 2.4 4.7 6.6 2.4 7.3 2.3 3.8 5.8 2.3 6.5 ns ns ns 5 SN54ABT534, SN74ABT534A OCTAL EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH 3-STATE OUTPUTS SCBS187F – JANUARY 1991 – REVISED JANUARY 1997 PARAMETER MEASUREMENT INFORMATION 500 Ω From Output Under Test S1 7V Open GND CL = 50 pF (see Note A) 500 Ω TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 7V Open 3V LOAD CIRCUIT Timing Input 1.5 V 0V tw tsu 3V th 3V 1.5 V Input 1.5 V 0V Data Input 1.5 V 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VOLTAGE WAVEFORMS PULSE DURATION 3V 1.5 V Input 1.5 V 0V VOH 1.5 V Output 1.5 V VOL VOH 1.5 V 1.5 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 1.5 V 1.5 V 0V tPZL tPLZ Output Waveform 1 S1 at 7 V (see Note B) tPLH tPHL Output 3V Output Control tPHL tPLH 1.5 V Output Waveform 2 S1 at Open (see Note B) 1.5 V 3.5 V VOL + 0.3 V VOL tPHZ tPZH 1.5 V VOH – 0.3 V VOH ≈0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. Figure 1. Load Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated