SCDS104C − APRIL 2000 − REVISED SEPTEMBER 2003 D Member of the Texas Instruments D D TTL-Compatible Input Levels D Flow-Through Architecture Optimizes PCB Widebus+ Family 5-Ω Switch Connection Between Two Ports Layout description/ordering information The SN74CBT32245 provides 32 bits of high-speed TTL-compatible bus switching. The low on-state resistance of the switch allows connections to be made with minimal propagation delay. The device is organized as four 8-bit bus switches, two 16-bit bus switches, or one 32-bit bus switch. When output enable (OE) is low, the switch is on and port A is connected to port B. When OE is high, the switch is open and the high-impedance state exists between the two ports. ORDERING INFORMATION ORDERABLE PART NUMBER PACKAGE† TA LFBGA − GKE −40°C to 85°C TOP-SIDE MARKING SN74CBT32245GKER LFBGA − ZKE (Pb-free) Tape and reel SN74CBT32245ZKER BV245 † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. FUNCTION TABLE (each 8-bit bus switch) INPUT OE FUNCTION L A port = B port H Disconnect Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus+ is a trademark of Texas Instruments. Copyright 2003, Texas Instruments Incorporated !"# $"%&! '#( '"! ! $#!! $# )# # #* "# '' +,( '"! $!#- '# #!#&, !&"'# #- && $##( POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SCDS104C − APRIL 2000 − REVISED SEPTEMBER 2003 GKE OR ZKE PACKAGE (TOP VIEW) 1 2 3 4 5 terminal assignments 6 1 2 3 4 5 6 A A 1B2 1B1 NC 1OE 1A1 1A2 B B 1B4 1B3 GND GND 1A3 1A4 C C 1B6 1B5 1B7 VCC GND 1A6 1B8 VCC GND 1A5 D 1A7 1A8 E 2B2 2B1 GND GND 2A1 2A2 F 2B4 2B3 2A4 2B6 2B5 VCC GND 2A3 G VCC GND 2A5 2A6 H 2B7 2B8 NC 2OE 2A8 2A7 J 3B2 3B1 NC 3OE 3A1 3A2 D E F G H J K 3B4 3B3 GND GND 3A3 3A4 K L 3B6 3B5 3A6 M 3B8 3B7 VCC GND 3A5 L VCC GND 3A7 3A8 M N 4B2 4B1 GND GND 4A1 4A2 N P 4B4 4B3 4A4 R 4B6 4B5 VCC GND 4A3 P VCC GND 4A5 4A6 R T 4B7 4B8 NC 4OE 4A8 4A7 NC − No internal connection T logic diagram (positive logic) 1A1 A5 A2 D6 D1 1A8 1B1 2A1 1B8 2A8 A4 H5 H2 2B1 2B8 2OE J5 J2 M6 M1 3A8 3B1 4A1 3B8 4A8 J4 N5 N2 T5 T2 T4 3OE 2 E2 H4 1OE 3A1 E5 4OE POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 4B1 4B8 SCDS104C − APRIL 2000 − REVISED SEPTEMBER 2003 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V Continuous channel current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Input clamp current, IIK (VI/O < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA Package thermal impedance, θJA (see Note 2): GKE/ZKE package . . . . . . . . . . . . . . . . . . . . . . . . . . . 40°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions (see Note 3) MIN MAX 5.5 VCC VIH Supply voltage 4 High-level control input voltage 2 VIL TA Low-level control input voltage Operating free-air temperature −40 UNIT V V 0.8 V 85 °C NOTE 3: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to TI application report Implications of Slow or Floating CMOS Inputs, literature number SCBA004. electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS VIK II VCC = 4.5 V, VCC = 5.5 V, II = −18 mA VI = 5.5 V or GND ICC ∆ICC§ Control inputs VCC = 5.5 V, VCC = 5.5 V, IO = 0, One input at 3.4 V, Ci Control inputs VI = 3 V or 0 VO = 3 V or 0, OE = VCC Cio(OFF) VCC = 4 V, TYP at VCC = 4 V ron¶ VCC = 4.5 V MIN TYP‡ VI = VCC or GND Other inputs at VCC or GND MAX UNIT −1.2 V ±5 µA 6 µA 3.5 mA 3.5 pF 4.5 pF VI = 2.4 V, II = 15 mA 14 20 II = 64 mA II = 30 mA 5 7 VI = 0 5 7 Ω VI = 2.4 V, II = 15 mA 8 12 ‡ All typical values are at VCC = 5 V (unless otherwise noted), TA = 25°C. § This is the increase in supply current for each input that is at the specified TTL-voltage level, rather than VCC or GND. ¶ Measured by the voltage drop between the A and B terminals at the indicated current through the switch. On-state resistance is determined by the lower of the voltages of the two (A or B) terminals. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SCDS104C − APRIL 2000 − REVISED SEPTEMBER 2003 switching characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1) VCC = 4 V VCC = 5 V ± 0.5 V MIN MIN FROM (INPUT) TO (OUTPUT) tpd† A or B B or A 0.35 ten OE A or B 6.1 OE A or B 7.5 PARAMETER tdis MAX UNIT MAX 0.25 ns 1.2 5.6 ns 3.9 7.7 ns † The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance, when driven by an ideal voltage source (zero output impedance). PARAMETER MEASUREMENT INFORMATION 7V 500 Ω From Output Under Test S1 Open GND CL = 50 pF (see Note A) 500 Ω TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 7V Open 3V Output Control LOAD CIRCUIT 1.5 V 1.5 V 0V tPLZ tPZL 3V Input 1.5 V 1.5 V 0V tPLH 1.5 V 3.5 V 1.5 V 1.5 V VOL Output Waveform 2 S1 at Open (see Note B) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES VOL + 0.3 V VOL tPHZ tPZH tPHL VOH Output Output Waveform 1 S1 at 7 V (see Note B) 1.5 V VOH VOH − 0.3 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. H. All parameters and waveforms are not applicable to all devices. Figure 1. Load Circuit and Voltage Waveforms 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 25-Feb-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SN74CBT32245GKER ACTIVE LFBGA GKE 96 1000 SN74CBT32245ZKER ACTIVE LFBGA ZKE 96 1000 Green (RoHS & no Sb/Br) None Lead/Ball Finish MSL Peak Temp (3) SNPB Level-3-220C-168 HR SNAGCU Level-3-250C-168 HR (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. None: Not yet available Lead (Pb-Free). Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens, including bromine (Br) or antimony (Sb) above 0.1% of total product weight. (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated