SLLS018E − JUNE 1986 − REVISED JUNE 2004 D Suitable for IEEE Standard 488-1978 (GPIB) D 8-Channel Bidirectional Transceivers D High-Speed Advanced Low-Power Schottky D D D D D D D (ALS) Circuitry Low Power Dissipation . . . 46 mW Max Per Channel Fast Propagation Times . . . 20 ns Max High-Impedance pnp Inputs Receiver Hysteresis . . . 650 mV Typ Open-Collector Driver Output Option No Loading of Bus When Device Is Powered Down (VCC = 0) Power-Up/Power-Down Protection (Glitch Free) DW OR N PACKAGE (TOP VIEW) GPIB I/O Ports TE B1 B2 B3 B4 B5 B6 B7 B8 GND 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC D1 D2 D3 D4 D5 D6 D7 D8 PE Terminal I/O Ports description/ordering information The SN75ALS160 eight-channel general-purpose interface bus transceivers are monolithic, high-speed, advanced low-power Schottky (ALS) devices designed for two-way data communications over single-ended transmission lines. This device is designed to meet the requirements of IEEE Standard 488 - 1978. The transceivers feature driver outputs that can be operated in either the passive-pullup or 3-state mode. If talk enable (TE) is high, these ports have the characteristics of passive-pullup outputs when pullup enable (PE) is low and of 3-state outputs when PE is high. Taking TE low places these ports in the high-impedance state. The driver outputs are designed to handle loads up to 48 mA of sink current. An active turn-off feature has been incorporated into the bus-terminating resistors so that the device exhibits a high impedance to the bus when VCC = 0. When combined with the SN75ALS161 or SN75ALS162 bus management transceiver, the pair provides the complete 16-wire interface for the IEEE - 488 bus. The SN75ALS160 is characterized for operation from 0°C to 70°C. ORDERING INFORMATION PACKAGE† TA PDIP (N) 0°C 0 C to 70 70°C C SOIC (DW) ORDERABLE PART NUMBER Tube of 20 SN75ALS160N Tube of 25 SN75ALS160DW Reel of 2000 SN75ALS160DWR TOP-SIDE MARKING SN75ALS160N 75ALS160 † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2004, Texas Instruments Incorporated ! "#$ ! %#&'" ($) (#"! " !%$""! %$ *$ $! $+! !#$! !(( ,-) (#" %"$!!. ($! $"$!!'- "'#($ $!. '' %$$!) POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SLLS018E − JUNE 1986 − REVISED JUNE 2004 Function Tables EACH DRIVER INPUTS D TE PE OUTPUT B H H H H L H X H X L X L X L Z† Z† EACH RECEIVER INPUTS B TE PE OUTPUT D L L X L H L X H X H X Z H = high level, L = low level, X = irrelevant, Z = high-impedance state † This is the high-impedance state of a normal 3-state output modified by the internal resistors to VCC and GND. logic diagram (positive logic) PE TE D1 11 1 19 2 B1 18 D2 3 D3 4 D4 Terminal I/O Ports GPIB I/O Ports B5 14 7 D7 B4 15 6 D6 B3 16 5 D5 B2 17 B6 13 8 B7 12 D8 9 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 B8 SLLS018E − JUNE 1986 − REVISED JUNE 2004 schematics of inputs and outputs EQUIVALENT OF ALL CONTROL INPUTS EQUIVALENT OF ALL INPUT/OUTPUT PORTS VCC 9 kΩ NOM R(eq) 1.7 kΩ NOM 10 kΩ NOM Input 4 kΩ NOM 4 kΩ NOM GND Input/Output Port Driver output R(eq) = 30 Ω NOM Receiver output R(eq) = 110 Ω NOM R(eq) = equivalent resistor Circuit inside dashed lines is on the driver outputs only. absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V Low-level driver output current, IOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mA Package thermal impedance, θJA (see Notes 2 and 3): DW package . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69°C/W Operating virtual junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values are with respect to network ground terminal. 2. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) − TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability. 3. The package thermal impedance is calculated in accordance with JESD 51-7. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SLLS018E − JUNE 1986 − REVISED JUNE 2004 recommended operating conditions VCC VIH Supply voltage VIL Low-level input voltage IOH High-level output current High-level input voltage MIN NOM MAX UNIT 4.75 5 5.25 V 2 V 0.8 IOL Low-level output current TA Operating free-air temperature V Bus ports with pullups active − 5.2 mA Terminal ports − 800 µA Bus ports 48 Terminal ports 16 0 70 mA °C electrical characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) TEST CONDITIONS† PARAMETER VIK Input clamp voltage II = − 18 mA, Vhys Hysteresis voltage (VIT+ − VIT−) VOH§ High-level output voltage Terminal Low-level output voltage Terminal VOL II MIN VCC = MIN Bus IOH = − 800 µA, IOH = − 5.2 mA, TE at 0.8 V, IOL = 16 mA, IOL = 48 mA, TE at 0.8 V, Bus Input current at maximum input voltage Terminal VI = 5.5 V, IIH High-level input current Terminal, PE, or TE IIL Low-level input current Terminal, PE, or TE VI/O(bus) Voltage at bus port Bus PE and TE at 2 V, VCC = MIN VCC = MIN Current into bus port IOS Short-circuit output current ICC Supply current UNIT − 1.5 V 0.4 0.65 2.7 3.5 2.5 3.3 VCC = MIN VCC = MIN V 0.5 0.5 VCC = MAX 0.2 100 µA VI = 2.7 V, VCC = MAX 0.1 20 µA VI = 0.5 V, VCC = MAX −10 −100 µA 3.7 V −1.5 V 2.5 3 0 − 3.2 2.5 − 3.2 VI(bus) = 2.5 V to 3.7 V Power on VI(bus) = 3.7 V to 5 V VI(bus) = 5 V to 5.5 V Terminal VCC = 0 VCC = MAX Bus VCC = MAX No load, VCC = MAX POST OFFICE BOX 655303 0 2.5 0.7 2.5 VI(bus) = 0 to 2.5 V 40 − 15 − 35 − 75 − 25 − 50 − 125 Terminal outputs low and enabled 42 65 Bus outputs low and enabled 52 80 • DALLAS, TEXAS 75265 V −1.3 CI/O(bus) Bus-port capacitance VCC = 0 to 5 V, VI/O = 0 to 2 V, f = 1 MHz 30 † For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. ‡ All typical values are at VCC = 5 V, TA = 25°C. § VOH applies to 3-state outputs only. 4 V 0.3 II(bus) = 0 II(bus) = −12 mA Power off MAX − 0.8 0.35 TE at 2 V, VI(bus) = −1.5 V to 0.4 V VI(bus) = 0.4 V to 2.5 V II/O(bus) TYP‡ mA µA mA mA pF SLLS018E − JUNE 1986 − REVISED JUNE 2004 switching characteristics at VCC = 4.75 V, 5 V, and 5.25 V, TA = 255C (unless otherwise noted) PARAMETER FROM (INPUT) TO (OUTPUT) TEST CONDITIONS Terminal Bus Bus TYP† MAX See Figure 1, CL = 50 pF 10 17 10 14 See Figure 2, CL = 50 pF 8 15 Terminal 8 15 24 30 9 14 Bus See Figure 3, CL = 50 pF 16 28 MIN tPLH tPHL Propagation delay time, low- to high-level output tPLH tPHL Propagation delay time, low- to high-level output tPZH tPHZ Output enable time to high level tPZL tPLZ Output enable time to low level Output disable time from low level 12 19 tPZH tPHZ Output enable time to high level 24 36 Output disable time from high level 10 18 tPZL tPLZ Output enable time to low level 15 26 15 24 16 24 9 16 Propagation delay time, high- to low-level output Propagation delay time, high- to low-level output Output disable time from high level TE TE Terminal See Figure 4, CL = 50 pF Output disable time from low level ten Output pullup enable time tdis Output pullup disable time † All typical values are at VCC = 5 V. PE Bus See Figure 5, CL = 50 pF UNIT ns ns ns ns ns switching characteristics over recommended range of operating free-air temperature, VCC = 5 V PARAMETER FROM (INPUT) TO (OUTPUT) Terminal Bus Bus Terminal TEST CONDITIONS TYP‡ MAX CL = 30 pF, See Figure 1 7 20 8 20 CL = 30 pF, See Figure 2 7 14 9 14 19 30 5 12 16 35 MIN tPLH tPHL Propagation delay time, low- to high-level output tPLH tPHL Propagation delay time, low- to high-level output tPZH tPHZ Output enable time to high level tPZL tPLZ Output enable time to low level 9 20 tPZH tPHZ Output enable time to high level 13 30 Output disable time from high level 12 20 tPZL tPLZ Output enable time to low level 12 20 11 20 11 22 6 12 Propagation delay time, high- to low-level output Propagation delay time, high- to low-level output Output disable time from high level TE Bus CL = 15 pF, See Figure 3 Output disable time from low level TE Terminal CL = 15 pF, See Figure 4 Output disable time from low level ten Output pullup enable time tdis Output pullup disable time ‡ Typical values are at TA = 25°C. PE POST OFFICE BOX 655303 Bus CL = 15 pF, See Figure 5 • DALLAS, TEXAS 75265 UNIT ns ns ns ns ns 5 SLLS018E − JUNE 1986 − REVISED JUNE 2004 PARAMETER MEASUREMENT INFORMATION 5V PE 3V Output Generator (see Note A) D 200 Ω 3V D Input 1.5 V 1.5 V 0 B tPHL tPLH CL = 30 pF (see Note B) 50 Ω VOH 480 Ω B Output 2.2 V 1V VOH TE 3V TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, tr ≤ 6 ns, tf ≤ 6 ns, ZO = 50 Ω. B. CL includes probe and jig capacitance. Figure 1. Terminal-to-Bus Test Circuit and Voltage Waveforms 4.3 V TE 3V B Input Output 1.5 V 1.5 V 0 240 Ω Generator (see Note A) B tPLH D VOH CL = 30 pF (see Note B) 50 Ω tPHL 3 kΩ D Output 1.5 V 1.5 V VOL TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, tr ≤ 6 ns, tf ≤ 6 ns, ZO = 50 Ω. B. CL includes probe and jig capacitance. Figure 2. Bus-to-Terminal Test Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SLLS018E − JUNE 1986 − REVISED JUNE 2004 PARAMETER MEASUREMENT INFORMATION 5V 3V 200 Ω PE 3V TE Input Output S2 S1 D B CL = 15 pF (see Note B) 480 Ω 1.5 V 1.5 V 0 tPZH B Output S1 to 3 V S2 Open tPHZ 90% 2V 0.8 V tPZL Generator (see Note A) tPLZ 3.5 V B Output S1 to GND S2 Closed TE 50 Ω TEST CIRCUIT VOH 1V 0.5 V VOL VOLTAGE WAVEFORMS NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, tr ≤ 6 ns, tf ≤ 6 ns, ZO = 50 Ω. B. CL includes probe and jig capacitance. Figure 3. TE-to-Bus Test Circuit and Voltage Waveforms 3V 4.3 V TE Input Generator (see Note A) TE S2 50 Ω Output D 3V S1 CL = 15 pF (see Note B) B 3 kΩ 1.5 V 0 tPZH D Output S1 to 3 V S2 Open 240 Ω 1.5 V tPHZ 90% VOH 1.5 V 0 tPLZ tPZL 4V D Output S1 to GND S2 Closed TEST CIRCUIT 1V 0.7 V VOL VOLTAGE WAVEFORMS NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, tr ≤ 6 ns, tf ≤ 6 ns, ZO = 50 Ω. B. CL includes probe and jig capacitance. Figure 4. TE-to-Terminal Test Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 SLLS018E − JUNE 1986 − REVISED JUNE 2004 PARAMETER MEASUREMENT INFORMATION Generator (see Note A) PE 3V 50 Ω D PE Input B Output 1.5 V 1.5 V 0 CL = 15 pF (see Note B) RL = 480 Ω ten B Output tdis 90% VOH 2V VOL ≈0.8 3V TE TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, 50% duty cycle, tr ≤ 6 ns, tf ≤ 6 ns, ZO = 50 Ω. B. CL includes probe and jig capacitance. Figure 5. PE-to-Bus Test Circuit and Voltage Waveforms 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SLLS018E − JUNE 1986 − REVISED JUNE 2004 TYPICAL CHARACTERISTICS TERMINAL HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT TERMINAL LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT 0.6 3.5 VOL − Low-Level Output Voltage − V VCC = 5 V TA = 25°C 3 2.5 2 1.5 1 0.5 VCC = 5 V TA = 25°C 0.5 0.4 0.3 0.2 0.1 0 0 0 − 5 − 10 − 15 − 20 − 25 − 30 − 35 IOH − High-Level Output Current − mA 0 − 40 30 40 50 10 20 IOL − Low-Level Output Current − mA Figure 6 60 Figure 7 TERMINAL OUTPUT VOLTAGE vs BUS INPUT VOLTAGE 4 VCC = 5 V No Load TA = 25°C 3.5 VO − Output Voltage − V VOH − High-Level Output Voltage − V 4 3 2.5 2 VIT + VIT − 1.5 1 0.5 0 0 0.2 0.4 0.6 0.8 1 1.2 1.4 VI − Input Voltage − V 1.6 1.8 2 Figure 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 SLLS018E − JUNE 1986 − REVISED JUNE 2004 TYPICAL CHARACTERISTICS BUS HIGH-LEVEL OUTPUT VOLTAGE vs BUS HIGH-LEVEL OUTPUT CURRENT BUS LOW-LEVEL OUTPUT VOLTAGE vs BUS LOW-LEVEL OUTPUT CURRENT 0.6 4 VOL− Low-Level Output Voltage − V VOH − High-Level Output Voltage − V VCC = 5 V TA = 25°C 3 2 1 VCC = 5 V TA = 25°C 0.5 0.4 0.3 0.2 0.1 0 0 0 − 10 − 20 − 30 − 40 − 50 0 − 60 10 20 30 40 50 60 70 80 90 100 IOL − Low-Level Output Current − mA IOH − High-Level Output Current − mA Figure 9 Figure 10 BUS OUTPUT VOLTAGE vs TERMINAL INPUT VOLTAGE BUS CURRENT vs BUS VOLTAGE 4 2 VCC = 5 V TA = 25°C 1 I I/O(bus) − Bus Current − mA II/O(bus) VO − Output Voltage − V VCC = 5 V No Load TA = 25°C 3 2 1 0 −1 −2 −3 −4 −5 The Unshaded Area Conforms to Paragraph 3.5.3 of IEEE Standard 488 - 1978 −6 0 0.9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 −7 −2 −1 VI − Input Voltage − V 1 2 3 4 VI/O(bus) − Bus Voltage − V Figure 11 10 0 Figure 12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 6 PACKAGE OPTION ADDENDUM www.ti.com 10-May-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SN75ALS160DW ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75ALS160DWE4 ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75ALS160DWG4 ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75ALS160DWR ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75ALS160DWRE4 ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75ALS160DWRG4 ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75ALS160N ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type SN75ALS160NE4 ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 4-Oct-2007 TAPE AND REEL BOX INFORMATION Device SN75ALS160DWR Package Pins DW 20 Site Reel Diameter (mm) Reel Width (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) SITE 60 330 24 10.8 13.1 2.65 12 Pack Materials-Page 1 W Pin1 (mm) Quadrant 24 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 4-Oct-2007 Device Package Pins Site Length (mm) Width (mm) Height (mm) SN75ALS160DWR DW 20 SITE 60 346.0 346.0 41.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Telephony www.ti.com/telephony Low Power Wireless www.ti.com/lpw Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated