STMICROELECTRONICS STM660OFU52DM6F

STM6600
STM6601
Smart push-button on/off controller with
Smart ResetTM and power-on lockout
Features
■
Operating voltage 1.6 V to 5.5 V
■
Low standby current of 1 µA
■
Adjustable Smart Reset™ assertion delay time
driven by external CSRD
■
Power-up duration determined primarily by
push-button press (STM6600) or by fixed time
period, tON_BLANK (STM6601)
■
Debounced PB and SR inputs
■
PB and SR ESD inputs withstand voltage up to
±15 kV (air discharge) ±8 kV (contact
discharge)
■
Active high or active low enable output option
(EN or EN) provides control of MOSFET,
DC-DC converter, regulator, etc.
■
Secure startup, interrupt, Smart Reset™ or
power down driven by push-button
■
Precise 1.5 V voltage reference with 1%
accuracy
■
Industrial operating temperature –40 to +85 °C
■
Available in TDFN12 2 x 3 mm package
Table 1.
TDFN12
Applications
■
Portable devices
■
Terminals
■
Audio and video players
■
Cell phones and smart phones
■
PDAs, palmtops, organizers
Device summary
Device
RST
CSRD
PB / SR
EN or EN
INT
Startup process
STM6600
open drain(1)
✓
✓
push-pull
open drain(1)
PB must be held low until the
PSHOLD(2) confirmation
STM6601
open drain(1)
✓
✓
push-pull
open drain(1)
PB can be released before the
PSHOLD(2) confirmation
1. External pull-up resistor needs to be connected to open drain outputs.
2. For a successful startup, the PSHOLD (Power Supply Hold) needs to be pulled high within specific time, tON_BLANK.
June 2010
Doc ID 15453 Rev 7
1/51
www.st.com
1
Contents
STM6600 - STM6601
Contents
1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2
Pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5
Typical operating characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7
DC and AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
8
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
9
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
10
Product selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
11
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
2/51
Doc ID 15453 Rev 7
STM6600 - STM6601
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Operating and AC measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
DC and AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
TDFN12 (2 x 3 mm) package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Carrier tape dimensions for TDFN12 (2 mm x 3 mm) package . . . . . . . . . . . . . . . . . . . . . 45
STM6600 ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
STM6601 ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
STM6600 product selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
STM6601 product selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Doc ID 15453 Rev 7
3/51
List of figures
STM6600 - STM6601
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Figure 23.
Figure 24.
Figure 25.
Figure 26.
Figure 27.
Figure 28.
Figure 29.
Figure 30.
Figure 31.
Figure 32.
Figure 33.
Figure 34.
Figure 35.
Figure 36.
Figure 37.
Figure 38.
Figure 39.
Figure 40.
Figure 41.
Figure 42.
Figure 43.
4/51
Application hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Basic functionality (option with enable deassertion after long push) . . . . . . . . . . . . . . . . . . 6
Basic functionality (option with RST assertion after long push) . . . . . . . . . . . . . . . . . . . . . . 6
Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
TDFN12 pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Successful power-up on STM6600
(PB released prior to tON_BLANK expiration) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Successful power-up on STM6600
(tON_BLANK expires prior to PB release) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Unsuccessful power-up on STM6600
(PB released prior to tON_BLANK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Unsuccessful power-up on STM6600
(tON_BLANK expires prior to PB release) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Successful power-up on STM6601 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Unsuccessful power-up on STM6601 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Power-up on STM660x with voltage dropout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
PB interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Long push, PB pressed first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Long push, SR pressed first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Invalid long push . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Long push (option with RST assertion). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Long push (option with enable deassertion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Undervoltage detected for <tSRD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Undervoltage detected for >tSRD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
PBOUT output waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Supply current vs. temperature, normal state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Supply current vs. temperature, standby state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Supply current vs. supply voltage, normal state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Supply current vs. supply voltage, standby state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Threshold vs. temperature, VTH+ = 3.4 V (typ.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Threshold hysteresis vs. temperature, VHYST = 200 mV (typ.) . . . . . . . . . . . . . . . . . . . . . . 30
Debounce period vs. supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
CSRD charging current vs. temperature, VCC = 3.6 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Output low voltage vs. output low current, TA = 25°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Output high voltage vs. output high current, TA = 25°C . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Output voltage vs. supply voltage, IOUT = 1 mA, TA = 25 °C . . . . . . . . . . . . . . . . . . . . . . . 33
Input voltage vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Reference output voltage vs. temperature, VCC = 2.0 V. . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Reference output voltage vs. load current, VCC = 2.0 V, TA = 25 °C . . . . . . . . . . . . . . . . . 34
Reference output voltage vs. supply voltage, TA = 25 °C . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Reference startup, IREF = 15 µF, TA = 25 °C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Reference response to steps on supply voltage, IREF = 15 µA, TA = 25 °C . . . . . . . . . . . . 36
Reference response to steps in load current, VCC = 3.6 V, TA = 25 °C . . . . . . . . . . . . . . . 37
TDFN12 (2 x 3 mm) package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
TDFN12 (2 x 3 mm) recommended footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Carrier tape for TDFN12 (2 mm x 3 mm) package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Doc ID 15453 Rev 7
STM6600 - STM6601
1
Description
Description
The STM6600-01 devices monitor the state of connected push-button(s) as well as sufficient
supply voltage. An enable output controls power for the application through the MOSFET
transistor, DC-DC converter, regulator, etc. If the supply voltage is above a precise voltage
threshold, the enable output can be asserted by a simple press of the button. Factoryselectable supply voltage thresholds are determined by highly accurate and temperaturecompensated references. An interrupt is asserted by pressing the push-button during
normal operation and can be used to request a system power-down. The interrupt is also
asserted if undervoltage is detected. By a long push of one button (PB) or two buttons (PB
and SR) either a reset is asserted or power for the application is disabled depending on the
option used.
The device also offers additional features such as precise 1.5 V voltage reference with very
tight accuracy of 1%, separate output indicating undervoltage detection and separate output
for distinguishing between interrupt by push-button or undervoltage.
The device consumes very low current of 6 µA during normal operation and only 1 µA
current during standby.
The STM6600-01 is available in the TDFN12 package and is offered in several options
among features such as selectable threshold, hysteresis, timeouts, output types, etc. (see
Table 8 and Table 9 for more information).
Figure 1.
Application hookup
$#$#CONVERTER
POWER-/3&%4
REGULATORETC
2
,%$
6##
%.%.
234
6## ,/
2
2
34-
34-
0" /54
)/
6
2%&
#32$
6$$
.-)OR).4
).4
32
234
)/
03
(/,$
0"
'.$
2 #2%&
-#5
#05
"!3%"!.$
#32$
!-V
!-V
1. A resistor is required for open drain output type only. A 10 kΩ pull-up is sufficient in most applications.
2. Capacitor CREF is mandatory on VREF output (even if VREF is not used). Capacitor value of 1 µF is recommended.
3. For the STM6601 the processor has to confirm the proper power-on during the fixed time period, tON_BLANK. This failsafe
feature prevents the user from turning on the system when there is a faulty power switch or an unresponsive
microprocessor.
Doc ID 15453 Rev 7
5/51
Description
STM6600 - STM6601
Figure 2.
Basic functionality (option with enable deassertion after long push)
INTERRUPT
(short push)
POWER-UP(1)
POWER DOWN
(long push)
PB
SR
EN
INT
interrupt
interrupt
AM00243v1
1. For power-up the battery voltage has to be above VTH+ threshold.
Figure 3.
Basic functionality (option with RST assertion after long push)
INTERRUPT
(short push)
POWER-UP(1)
POWER DOWN
(long push)
PB
SR
RST
INT
interrupt
interrupt
AM00243bv1
1. For power-up the battery voltage has to be above VTH+ threshold.
Figure 4.
Logic diagram
VCC
EN (EN)
RST
PB
SR
PSHOLD
STM6600
STM6601
INT
PBOUT
VCC LO
CSRD
VREF
GND
6/51
Doc ID 15453 Rev 7
AM00236v1
STM6600 - STM6601
Table 2.
Description
Pin descriptions
Pin number
Symbol
1
VCC
Power supply input
2
SR
Smart Reset™ button input
3
VREF
4
PSHOLD
5
CSRD
6
PB
7
VCCLO
Output for high threshold comparator output (VTH+)
8
PBOUT
Status of PB push-button input
9
EN or EN
Enable output
10
RST
Reset output
11
INT
Interrupt output
12
GND
Ground
Figure 5.
Function
Precise 1.5 V voltage reference
PSHOLD input
Adjustable Smart Reset™ delay time input
Push-button input
TDFN12 pin connections
VCC
1
12
GND
SR
2
11
INT
VREF
3
10
RST
PSHOLD
4
9
EN (EN)
CSRD 5
8
PBOUT
7
VCC LO
PB
6
AM00245v1
Doc ID 15453 Rev 7
7/51
Description
Figure 6.
STM6600 - STM6601
Block diagram
VCC LO
VCC VCC
(1)
RPB
PB
(2)
RSR
EN (EN)
VCC
+
+
–
–
VTH+
RST
tREC
generator
PSHOLD
VTH–
Smart
logic
Glitch immunity
Edge detector debounce
(3)
RPSHOLD
INT
SR
Glitch immunity
Edge detector debounce
VREF
GND
SRD logic
PBOUT
1.5 V
CSRD
AM00237v3
1. Internal pull-up resistor connected to PB input (see Table 5 for precise specifications).
2. Optional internal pull-up resistor connected to SR input (see Table 5 for precise specifications and Table 10 for detailed
device options).
3. Internal pull-down resistor is connected to PSHOLD input only during startup (see Figure 7, 8, 9, 10, 11, 12, 13, and 18).
8/51
Doc ID 15453 Rev 7
STM6600 - STM6601
2
Pin descriptions
Pin descriptions
VCC - power supply input
VCC is monitored during startup and normal operation for sufficient voltage level. Decouple
the VCC pin from ground by placing a 0.1 µF capacitor as close to the device as possible.
SR - Smart Reset™ button input
This input is equipped with voltage detector with a factory-trimmed threshold and has ±8 kV
HBM ESD protection.
Both PB and SR buttons have to be pressed and held for tSRD period so the long push is
recognized and the reset is asserted (or the enable output is deasserted depending on the
option) - see Figure 15, 16, and 17.
Active low SR input is usually connected to GND through the momentary push-button (see
Figure 1) and it has an optional 100 kΩ pull-up resistor. It is also possible to drive this input
using an external device with either open drain (recommended) or push-pull output. Open
drain output can be connected in parallel with push-button or other open drain outputs,
which is not possible with push-pull output.
VREF - external precise 1.5 V voltage reference
This 1.5 V voltage reference is specified with very tight accuracy of 1% (see Table 5). It has
proper output voltage as soon as the reset output is deasserted (i.e. after tREC expires) and
it is disabled when the device enters standby mode. A mandatory capacitor needs to be
connected to VREF output (even if VREF is not used). Capacitor value of 1 µF is
recommended.
PSHOLD input
This input is equipped with a voltage detector with a factory-trimmed threshold. It is used to
confirm correct power-up of the device (if EN or EN is not asserted) or to initiate a shutdown
(if EN or EN is asserted).
Forcing PSHOLD high during power-up confirms the proper start of the application and keeps
enable output asserted. Because most processors have outputs in high-Z state before
initialization, an internal pull-down resistor is connected to PSHOLD input during startup (see
Figure 7, 8, 9, 10, 11, 12, 13, and 18).
Forcing the PSHOLD signal low during normal operation deasserts the enable output (see
Figure 14). Input voltage on this pin is compared to an accurate voltage reference.
CSRD - Smart Reset™delay time input
A capacitor to ground determines the additional time (tSRD) that PB with SR must be
pressed and held before a long push is recognized. The connected CSRD capacitor is
charged with ISRD current. Additional Smart Reset™ delay time tSRD ends when voltage on
the CSRD capacitor reaches the VSRD voltage threshold. It is recommended to use a low
ESR capacitor (e.g. ceramic). If the capacitor is not used, leave the CSRD pin open. If no
capacitor is connected, there is no tSRD and a long push is recognized right after tINT_Min
expires (see Figure 18 and 19).
Doc ID 15453 Rev 7
9/51
Pin descriptions
STM6600 - STM6601
PB - power ON switch
This input is equipped with a voltage detector with a factory-trimmed threshold and has
± 8 kV HBM ESD protection.
When the PB button is pressed and held, the battery voltage is detected and EN (or EN) is
asserted if the battery voltage is above the threshold VTH+ during the whole tDEBOUNCE
period (see Figure 13).
A short push of the push-button during normal operation can initiate an interrupt through
debounced INT output (see Figure 14) and a long push of PB and SR simultaneously can
either assert reset output RST (see Figure 18) or deassert the EN or EN output (see
Figure 19) based on the option used.
Note:
A switch to GND must be connected to this input (e.g. mechanical push-button, open drain
output of external circuitry, etc.), see Figure 1. This ensures a proper startup signal on PB
(i.e. a transition from full VCC below specified VIL). PB input has an internal 100 kΩ pull-up
resistor connected.
VCCLO - high threshold detection output
During power-up, VCCLO is low when VCC supply voltage is below the VTH+ threshold. After
successful power-up (i.e. during normal operation) VCCLO is low anytime undervoltage is
detected (see Figure 13).
Output type is active low and open drain by default. Open drain output type requires a pullup resistor. A 10 kΩ is sufficient in most applications.
VCCLO is floating when STM660x is in standby mode.
PBOUT - PB input state
If the push-button PB is pressed, the pin stays low during the tDEBOUNCE time period.
If PB is asserted for the entire tDEBOUNCE period, PBOUT will then stay low for at least
tINT_Min. If PB is asserted after tINT_Min expires, PBOUT will return high as soon as PB is
deasserted (see Figure 22). PBOUT ignores PB assertion during an undervoltage condition.
At startup on the STM6601 PBOUT will respond only to the first PB assertion and any other
assertion will be ignored until tON_BLANK expires. This output is active low and open drain by
default. Open drain output type requires a pull-up resistor. A 10 kΩ is sufficient in most
applications.
10/51
Doc ID 15453 Rev 7
STM6600 - STM6601
Pin descriptions
EN or EN - enable output
This output is intended to enable system power (see Figure 1). EN is asserted high after
a valid turn-on event has been detected and confirmed (i.e. push-button has been pressed
and held for tDEBOUNCE or more and VCC > VTH+ voltage level has been detected - see
Figure 13). EN is released low if any of the conditions below occur:
a)
the push-button is released before PSHOLD is driven high (valid for STM6600, see
Figure 9) or tON_BLANK expires before PSHOLD is driven high during startup (valid
for both STM6600 and STM6601, see Figure 10 and 12).
b)
PSHOLD is driven low during normal operation (see Figure 14).
c)
an undervoltage condition is detected for more than tSRD + tINT_Min + tDEBOUNCE
(see Figure 21).
d)
a long push of the buttons is detected (only for the device with option “EN
deasserted by long push” - see Figure 19) or PSHOLD is not driven high during
tON_BLANK after a long push of the buttons (only for the device with option “RST
asserted by long push” - see Figure 18).
Described logic levels are inverted in case of EN output. Output type is push-pull by default.
RST - reset output
This output pulls low for tREC:
a)
during startup. PB has been pressed (falling edge on the PB detected) and held
for at least tDEBOUNCE and VCC > VTH+ (see Figure 7, 8, 9, 10, 11, 12 and 13 for
more details).
b)
after long push detection (valid only for the device with option “RST asserted by
long push”). PB has been pressed (falling edge on the PB detected) and held for
more than tDEBOUNCE + tSRD (additional Smart Reset™ delay time can be adjusted
by the external capacitor CSRD) - see Figure 18.
Output type is active low and open drain by default. Open drain output type requires a pullup resistor. A 10 kΩ is sufficient in most applications.
INT - interrupt output
While the system is under normal operation (PSHOLD is driven high, power for application is
asserted), the INT is driven low if:
a)
VCC falls below VTH- threshold (i.e. undervoltage is detected - see Figure 20 and
21).
b)
the falling edge on the PB is detected and the push-button is held for tDEBOUNCE or
more. INT is driven low after tDEBOUNCE and stays low as long as PB is held. The
INT signal is held high during power-up.
The state of the PBOUT output can be used to determine if the interrupt was caused by
either the assertion of the PB input, or was due to the detection of an undervoltage condition
on VCC.
INT output is asserted low for at least tINT_Min.
Output type is active low and open drain by default. Open drain output type requires a pullup resistor. A 10 kΩ is sufficient in most applications.
GND - ground
Doc ID 15453 Rev 7
11/51
Operation
3
STM6600 - STM6601
Operation
The STM6600-STM6601 simplified smart push-button on/off controller with Smart Reset™
and power-on lockout enables and disables power for the application depending on pushbutton states, signals from the processor, and battery voltage.
Power-on
Because most of the processors have outputs in high-Z state before initialization, an internal
pull-down resistor is connected to PSHOLD input during startup (see Figure 7, 8, 9, 10, 11,
12, 13, and 18).
To power up the device the push-button PB has to be pressed for at least tDEBOUNCE and
VCC has to be above VTH+ for the whole tDEBOUNCE period. If the battery voltage drops
below VTH+ during the tDEBOUNCE, the counter is reset and starts to count again when VCC >
VTH+ (see Figure 13). After tDEBOUNCE the enable signal is asserted (EN goes high, EN
goes low), reset output RST is asserted for tREC and then the startup routine is performed
by the processor. During initialization, the processor sets the PSHOLD signal high.
On the STM6600 the PSHOLD signal has to be set high prior to push-button release and
tON_BLANK expiration, otherwise the enable signal is deasserted (EN goes low, EN goes
high) - see Figure 7, 8, 9, and 10. The time up to push-button release represents the
maximum time allowed for the system to power up and initialize the circuits driving the
PSHOLD input. If the PSHOLD signal is low at push-button release, the enable output is
deasserted immediately, thus turning off the system power. If tON_BLANK expires prior to
push-button release, the PSHOLD state is checked at its expiration. This safety feature
disables the power and prevents discharging the battery if the push-button is stuck or it is
held for an unreasonable period of time and the application is not responding (see Figure 8
and 10). PB status, INT status and VCC undervoltage detection are not monitored until
power-up is completed.
On the STM6601 the PSHOLD signal has to be set high before tON_BLANK expires, otherwise
the enable signal is deasserted - see Figure 11 and 12. In this case the tON_BLANK period is
the maximum time allowed for the power switch and processor to perform the proper poweron. If the PSHOLD signal is low at the end of the blanking period, the enable output is
released immediately, thus turning off the system power. PB status, INT status and VCC
undervoltage detection are not monitored during the entire tON_BLANK period. This failsafe
feature prevents the user from turning on the system when there is a faulty power switch or
an unresponsive microprocessor.
Push-button interrupt
If the device works under normal operation (i.e. PSHOLD is high) and the push-button PB is
pressed for more than tDEBOUNCE, a negative pulse with minimum tINT_Min width is
generated on the INT output. By connecting INT to the processor interrupt input (INT or
NMI) a safeguard routine can be performed and the power can be shut down by setting
PSHOLD low - see Figure 14.
Forced power-down mode
The PSHOLD output can be forced low anytime during normal operation by the processor
and can deassert the enable signal - see Figure 14.
12/51
Doc ID 15453 Rev 7
STM6600 - STM6601
Operation
Undervoltage detection
If VCC voltage drops below VTH- voltage threshold during normal operation, the INT output is
driven low (see Figure 20 and Figure 21).
If an undervoltage condition is detected for tDEBOUNCE + tINT_Min + tSRD, the enable output is
deasserted (see Figure 21).
Hardware reset or power-down while system not responding
If the system is not responding and the system hangs, the PB and SR push-buttons can be
pressed simultaneously longer than tDEBOUNCE + tINT_Min + tSRD, and then
a)
either the reset output RST is asserted for tREC and the processor is reset (valid
only for the device with option “RST asserted by long push”) – see Figure 18
b)
or the power is disabled by EN or EN signal (valid only for the device with option
“EN deasserted by long push”) – see Figure 19
The tSRD is set by the external capacitor connected to the CSRD pin.
Standby
If the enable output is deasserted (i.e. EN is low or EN is high), the STM660x device enters
standby mode with low current consumption (see Table 5). In standby mode PB input is only
monitored for the falling edge. The external 1.5 V voltage reference is also disabled in
standby mode.
Doc ID 15453 Rev 7
13/51
Waveforms
STM6600 - STM6601
4
Waveforms
Figure 7.
Successful power-up on STM6600 (PB released prior to tON_BLANK expiration)
Push-button pressed and
PB connected to GND
processor
sets PSHOLD
PB released prior to t ON_BLANK
expiration
PSHOLD state detected as high
EN remains asserted
VCC undervoltage detection
ignored
PSHOLD
ignored
internal pull-down resistor
connected to PSHOLD input
PB(1)
PSHOLD(2)
EN(3)
RST
tDEBOUNCE
tREC
tON_BLANK
Note: INT signal is held high during power-up (i.e. until PB release in this case).
VCC is considered VCC > VTH+.
AM00247v3
1. PB detection on falling and rising edges.
2. Internal pull-down resistor 300 kΩ is connected to PSHOLD input during power-up.
3. EN signal is high even after PB release, because processor sets PSHOLD signal high before PB is released.
14/51
Doc ID 15453 Rev 7
STM6600 - STM6601
Figure 8.
Waveforms
Successful power-up on STM6600 (tON_BLANK expires prior to PB release)
Push-button pressed and
PB connected to GND
processor
sets PSHOLD
tON_BLANK expired prior to PB
release
PSHOLD state detected as high
EN remains asserted
PB released
VCC undervoltage detection
ignored
PSHOLD
ignored
internal pull-down resistor
connected to PSHOLD input
PB(1)
PSHOLD(2)
EN(3)
RST
tDEBOUNCE
tREC
tON_BLANK
Note: INT signal is held high during power-up (i.e. until tON_BLANK expires in this case).
VCC is considered VCC > VTH+.
AM00247bv2
1. PB detection on falling and rising edges.
2. Internal pull-down resistor 300 kΩ is connected to PSHOLD input during power-up.
3. tON_BLANK expires prior to PB release so PSHOLD is checked at its expiration.
Doc ID 15453 Rev 7
15/51
Waveforms
Figure 9.
STM6600 - STM6601
Unsuccessful power-up on STM6600 (PB released prior to tON_BLANK)
PB released
PSHOLD state detected as low
EN deasserted
Push-button pressed and
PB connected to GND
VCC undervoltage detection
ignored
PSHOLD
ignored
internal pull-down resistor
connected to PSHOLD input
PB(1)
PSHOLD(2)
PB status
ignored
EN(3)
RST
tDEBOUNCE
tEN_OFF
tREC
tON_BLANK
Note: INT signal is held high during power-up (i.e. until PB release in this case).
VCC is considered VCC > VTH+.
AM00248v3
1. PB detection on falling and rising edges.
2. Internal pull-down resistor 300 kΩ is connected to PSHOLD input during power-up.
3. EN signal goes low with PB release, because processor did not force PSHOLD signal high.
16/51
Doc ID 15453 Rev 7
STM6600 - STM6601
Waveforms
Figure 10. Unsuccessful power-up on STM6600 (tON_BLANK expires prior to PB release)
tON_BLANK expired prior to PB release
PSHOLD state detected as low
EN is deasserted
Push-button pressed and
PB connected to GND
PB (1)
PB released
VCC undervoltage detection ignored
PB status
ignored
PSHOLD
ignored
internal pull-down resistor connected to
PSHOLD input
PSHOLD(2)
EN(3)
RST
tDEBOUNCE
tEN_OFF
tREC
tON_BLANK
Note: INT signal is held high during power-up (i.e. until tON_BLANK expires in this case).
VCC is considered VCC > VTH+.
AM00248bv2
1. PB detection on falling and rising edges.
2. Internal pull-down resistor 300 kΩ is connected to PSHOLD input during power-up.
3. tON_BLANK expires prior to PB release so PSHOLD is checked at its expiration.
Doc ID 15453 Rev 7
17/51
Waveforms
STM6600 - STM6601
Figure 11. Successful power-up on STM6601
tON_BLANK expires
processor
PSHOLD state detected as high
sets PSHOLD EN remains asserted
Push-button pressed and
PB connected to GND
PB
PB status and V CC undervoltage
detection ignored
(1)
PSHOLD ignored
(2)
PSHOLD
EN
internal pull-down resistor
connected to PSHOLD input
(3)
RST
t DEBOUNCE
t REC
t ON_BLANK
Note: INT signal is held high during power-up (i.e. until tON_BLANK expires in the case of the STM6601).
VCC is considered VCC > VTH+.
AM00250v2
1. PB detection on falling edge.
2. Internal pull-down resistor 300 kΩ is connected to PSHOLD input during power-up.
3. PSHOLD signal is ignored during tON_BLANK. When tON_BLANK expires, the level of the PSHOLD signal is high therefore the
EN signal remains asserted.
18/51
Doc ID 15453 Rev 7
STM6600 - STM6601
Waveforms
Figure 12. Unsuccessful power-up on STM6601
tON_BLANK expires
PSHOLD state detected as low Push-button pressed and
PB connected to GND
EN deasserted
Push-button pressed and
PB connected to GND
(1)
PB
PSHOLD ignored
(2)
PSHOLD
intenal pull-down resistor
connected to PSHOLD input
(3)
EN
RST
t
DEBOUNCE
t REC
Note: INT signal is held high during power-up (i.e. until tON_BLANK expires in the case of the STM6601).
VCC is considered VCC > VTH+.
AM00238v2
1. PB detection on falling edge.
2. Internal pull-down resistor 300 kΩ is connected to PSHOLD input during power-up.
3. PSHOLD signal is ignored during tON_BLANK. When tON_BLANK expires, the level of the PSHOLD signal is not high therefore
the EN signal goes low. Even releasing the PB button after the tON_BLANK will not prevent this.
Doc ID 15453 Rev 7
19/51
Waveforms
STM6600 - STM6601
Figure 13. Power-up on STM660x with voltage dropout
Push-button pressed and
PB connected to GND
VCC goes above VTH+ and
tDEBOUNCE is counted again
VTH+
VTH–
VCC
VCC LO
VCC–Min
VCC
undervoltage
detected
VCC
drop
(1)
PB
(2)
PSHOLD
INT
internal pull-down resistor
connected to PSHOLD input
(3)
INT signal is held high during power-up
EN
RST
< t DEBOUNCE
t DEBOUNCE
tREC
< t ON_BLANK
AM00249v2
1. PB detection on falling and rising edges.
2. Internal pull-down resistor 300 kΩ is connected to PSHOLD input during power-up.
3. INT signal is held high during power-up.
20/51
Doc ID 15453 Rev 7
STM6600 - STM6601
Waveforms
Figure 14. PB interrupt
processor interrupt starts power-down sequence
processor sets PSHOLD low
Push-button pressed and
PB connected to GND
PB
and EN is deasserted
accordingly
PB status
ignored
(1,2)
PSHOLD
PB status
ignored
VCC undervoltage
detection ignored
t DEBOUNCE
t INT_Min
tEN_OFF
Note: VCC is considered VCC > VTH+.
AM00251v2
1. PB detection on falling edge.
2. PB is released within tSRD and that is why NO reset is asserted and EN is NOT deasserted immediately.
Doc ID 15453 Rev 7
21/51
Waveforms
STM6600 - STM6601
Figure 15. Long push, PB pressed first
Push-button
PB is pressed
PB
Push-button tSRD starts to
SR is pressed be counted
tSRD
tDEBOUNCE
set by CSRD
tDEBOUNCE
SR
INT
PB status
ignored
tINT_Min
AM00257v1
Figure 16. Long push, SR pressed first
Push-button
SR is pressed
PB
Push-button
PB is pressed
tSRD starts to
be counted
tDEBOUNCE
tSRD
SR
set by CSRD
INT
PB status
ignored
tINT_Min
22/51
Doc ID 15453 Rev 7
AM00258v1
STM6600 - STM6601
Waveforms
Figure 17. Invalid long push
Push-button
PB is pressed
Push-button
SR is pressed
PB
tSRD starts to
be counted
Any rising edge will stop
tSRD to count regardless
of glitch immunity
tDEBOUNCE
< tSRD
SR
set by CSRD
INT
PB status
ignored
tINT_Min
AM00259v1
Doc ID 15453 Rev 7
23/51
Waveforms
STM6600 - STM6601
Figure 18. Long push (option with RST assertion)
Push-button pressed
and PB connected to
GND
tON_BLANK expires
PSHOLD state detected as high
therefore EN remains high
Push-button held even
after tSRD expires
therefore RST is asserted
tSRD(1)
set by CSRD
PB
After tON_BLANK
PB is monitored
for falling edge
tON_BLANK
(valid for STM6600 and STM6601)
SR
PB status
ignored
INT (2)
RST
INT can go high, if PB goes high,
but system freezes and processor
won’t respond
VCC undervoltage detection status ignored
PSHOLD ignored
if system freezes, processor won’t
respond to any INT status change
(3, 4)
PSHOLD
tDEBOUNCE
t INT_Min
internal pull-down resistor
connected to PSHOLD input
tREC
Note: EN is high.
tDEBOUNCE
AM00252v2
1. tSRD period is set by external capacitor CSRD.
2. PB ignored during tINT_Min.
3. PSHOLD signal is ignored during tON_BLANK. Its level is checked after tON_BLANK expires and if it is high the EN signal
remains asserted, otherwise EN goes low.
4. Internal pull-down resistor 300 kΩ is connected to PSHOLD input during startup when device is reset.
24/51
Doc ID 15453 Rev 7
STM6600 - STM6601
Waveforms
Figure 19. Long push (option with enable deassertion)
Push-button
pressed and PB
connected to GND
Push-button held even
after tSRD expires and
EN is deasserted
tSRD(1)
set by CSRD
PB
After tEN_OFF expires
PB is monitored for
falling edge
PB status
ignored
SR
INT can go high, if PB goes high,
PB status
but system freezes and processor
ignored
won’t respond
INT (2)
EN(3)
VCC undervoltage detection status ignored
if system freezes, processor won’t
respond to any INT status change
PSHOLD
tDEBOUNCE
t INT_Min
tEN_OFF
tDEBOUNCE
AM00253v2
1. tSRD period is set by external capacitor CSRD.
2. PB ignored during tINT_Min.
3. After tSRD expires EN is forced low.
Doc ID 15453 Rev 7
25/51
Waveforms
STM6600 - STM6601
Figure 20. Undervoltage detected for <tSRD
processor interrupt starts power-down sequence
VCC
undervoltage
detected
(1)
VCC
processor sets PSHOLD low
VTH+
tSRD
set by CSRD
(2)
VTH–
VCC-Min
PB status
ignored
and EN is deasserted
accordingly
VCC LO
PSHOLD
V CC
undervoltage
detection
ignored
INT
PB status ignored
EN
tINT_Min
tDEBOUNCE
tEN_OFF
AM00254v1
1. VCC goes above VTH+ within tSRD thus power is not disabled after tSRD expires.
2. tSRD period is set by external capacitor CSRD.
Figure 21. Undervoltage detected for >tSRD
VCC
undervoltage
detected
VCC is below VTH+ even after tSRD expires
thus power is disabled (EN goes low) and
PB is monitored for regular startup
VTH+
(1)
VCC
tSRD(2)
VTH–
set by CSRD
VCC-Min
VCCLO
PSHOLD
VCC
undervoltage
detection
ignored
INT
PB status ignored
PB status
ignored
EN
tDEBOUNCE
tINT_Min
tEN_OFF
AM00255v1
1. After tSRD expires VCC is still insufficient (below VTH+) thus power is disabled (EN goes low or EN goes high).
2. tSRD period is set by external capacitor CSRD.
26/51
Doc ID 15453 Rev 7
STM6600 - STM6601
Waveforms
Figure 22. PBOUT output waveform
<glitch immunity
(1,2,3,4)
PB
PBOUT
tDEBOUNCE
tINT_min
AM00256v1
1. Pulses on PB shorter than glitch immunity are ignored.
2. Pulses on PB shorter than tDEBOUNCE are not recognized by PBOUT.
3. Minimum pulse width on PBOUT is tINT_Min.
4. If push-button is held longer than tDEBOUNCE + tINT_Min, PBOUT goes high when the push-button is released.
Doc ID 15453 Rev 7
27/51
Typical operating characteristics
5
STM6600 - STM6601
Typical operating characteristics
Figure 23. Supply current vs. temperature, normal state
7.0
Supply current, ICC (µA)
6.5
6.0
5.5
5.0
4.5
VCC = 5.5 V
4.0
VCC = 3.6 V
VCC = 2.0 V
3.5
3.0
-40
-20
0
20
40
60
80
Temperature, TA (°C)
AM04701v1
Figure 24. Supply current vs. temperature, standby state
2.0
Supply current, ICC (µA)
VCC = 5.5 V
VCC = 3.6 V
1.5
VCC = 2.0 V
1.0
0.5
0.0
-40
-20
0
20
40
60
80
Temperature, TA (°C)
AM04702v1
28/51
Doc ID 15453 Rev 7
STM6600 - STM6601
Typical operating characteristics
Figure 25. Supply current vs. supply voltage, normal state
7
Supply current, ICC (µA)
6
5
4
3
TA = 85 °C
2
TA = 25 °C
TA = 0 °C
1
TA = –40 °C
0
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
Supply voltage, VCC (V)
AM04703v1
Figure 26. Supply current vs. supply voltage, standby state
1.5
Supply current, ICC (µA)
TA = 85 °C
TA = 25 °C
TA = 0 °C
1.0
TA = –40 °C
0.5
0.0
2.0
2.5
3.0
3.5
4.0
Supply voltage, VCC (V)
Doc ID 15453 Rev 7
4.5
5.0
5.5
AM04704v1
29/51
Typical operating characteristics
STM6600 - STM6601
Figure 27. Threshold vs. temperature, VTH+ = 3.4 V (typ.)
3.50
Threshold, V TH+ (V)
3.45
3.40
3.35
3.30
3.25
3.20
-40
-20
0
20
40
60
80
Tem perature, T A (°C)
AM04705v1
Figure 28. Threshold hysteresis vs. temperature, VHYST = 200 mV (typ.)
Threshold hysteresis, VHTYST (mV)
230
220
210
200
190
180
170
-40
-20
0
20
Tem perature, TA (°C)
30/51
Doc ID 15453 Rev 7
40
60
80
AM04706v1
STM6600 - STM6601
Typical operating characteristics
Figure 29. Debounce period vs. supply voltage
Debounce period, tDEBOUNCE (ms)
45
40
35
30
TA = 85 °C
25
TA = 25 °C
TA = 0 °C
20
TA = –40 °C
15
3.5
4
4.5
5
5.5
Supply voltage, VCC (V)
AM04707v1
Figure 30. CSRD charging current vs. temperature, VCC = 3.6 V
200
CSRD charging current, ISRD (nA)
190
180
170
160
150
140
130
VCC = 5.5 V
120
VCC = 3.6 V
110
VCC = 2 V
100
-40
-20
0
20
40
Temperature, TA (°C)
Doc ID 15453 Rev 7
60
80
AM04708v1
31/51
Typical operating characteristics
STM6600 - STM6601
Figure 31. Output low voltage vs. output low current, TA = 25°C
Output low voltage, VOL (V)
0.30
VCC =1.6V
0.25
VCC =3.6V
0.20
VCC =5.5V
0.15
0.10
0.05
0.00
0
1
2
3
4
5
Output low current, IOL (mA)
Note:
AM04709v1
Characteristics valid for all the outputs (EN, EN, RST, INT, PBOUT and VCCLO).
Figure 32. Output high voltage vs. output high current, TA = 25°C
0.8
Output high voltage, VCC - VOH (V)
VCC=1.6V
VCC=3.6V
0.6
VCC=5.5V
0.4
0.2
0
0
0.5
1
Output high current, IOH (mA)
Note:
32/51
Characteristics valid for EN and EN outputs.
Doc ID 15453 Rev 7
1.5
2
AM04710v1
STM6600 - STM6601
Typical operating characteristics
Figure 33. Output voltage vs. supply voltage, IOUT = 1 mA, TA = 25 °C
1
Output voltage, VOUT (V)
0.8
0.6
0.4
0.2
0
0
1
2
3
4
5
Supply voltage, VCC (V)
Note:
AM04711v1
Characteristics valid for all the outputs (EN, EN, RST, INT, PBOUT and VCCLO).
Figure 34. Input voltage vs. temperature
1.05
VCC = 3.6 V
1.04
Input voltage, VIN (V)
VCC = 5.5 V
1.03
1.02
1.01
1.00
0.99
-40
-20
0
20
Temperature, TA (°C)
Note:
40
60
80
AM04712v1
Characteristics valid for PB, SR and PSHOLD inputs.
Doc ID 15453 Rev 7
33/51
Typical operating characteristics
STM6600 - STM6601
Figure 35. Reference output voltage vs. temperature, VCC = 2.0 V
1.520
Reference output voltage, VREF (V)
1.515
IREF = 0 mA
1.510
IREF = 15 µA
1.505
1.500
1.495
1.490
1.485
1.480
-40
-20
0
20
40
60
80
Temperature, TA (°C)
Note:
AM04713v1
1 µF capacitor is connected to the VREF pin.
Figure 36. Reference output voltage vs. load current, VCC = 2.0 V, TA = 25 °C
Reference output voltage, VREF (V)
1.6
1.5
1.4
1.3
1.2
1.1
1
0
50
100
150
Load current, IREF (µA)
Note:
34/51
1 µF capacitor is connected to the VREF pin.
Doc ID 15453 Rev 7
200
250
300
AM04714v1
STM6600 - STM6601
Typical operating characteristics
Figure 37. Reference output voltage vs. supply voltage, TA = 25 °C
1.520
Reference output voltage, VREF (V)
1.515
1.510
1.505
1.500
1.495
IREF = 0 µA
1.490
IREF = 15 µA
1.485
1.480
2
2.5
3
3.5
4
Supply voltage, VCC (V)
Note:
4.5
5
5.5
AM04715v1
1 µF capacitor is connected to the VREF pin.
Figure 38. Reference startup, IREF = 15 µF, TA = 25 °C
Note:
1 µF capacitor is connected to the VREF pin.
Doc ID 15453 Rev 7
35/51
Typical operating characteristics
STM6600 - STM6601
Figure 39. Reference response to steps on supply voltage, IREF = 15 µA, TA = 25 °C
Note:
36/51
1
Supply voltage goes from 3.6 V to 5.5 V and back to 3.6 V, ramp 1 V / 100 ns.
2
1 µF capacitor is connected to the VREF pin.
Doc ID 15453 Rev 7
STM6600 - STM6601
Typical operating characteristics
Figure 40. Reference response to steps in load current, VCC = 3.6 V, TA = 25 °C
Note:
1
Supply voltage goes from 0 µA to 15 µA and back to 0 µA, ramp 1 µA / 100 ns.
2
1 µF capacitor is connected to the VREF pin.
Doc ID 15453 Rev 7
37/51
Maximum ratings
6
STM6600 - STM6601
Maximum ratings
Stressing the device above the rating listed in the absolute maximum ratings table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the operating sections of
this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability. Refer also to the STMicroelectronics SURE
Program and other relevant quality documents.
Table 3.
Symbol
VCC
Absolute maximum ratings
Parameter
Min.
Max.
Unit
Remarks
Input supply voltage
–0.3
+7.0
V
Input voltages on PB, SR, PSHOLD and
CSRD
–0.3
VCC + 0.3
V
Output voltages on EN (EN), RST and
INT
–0.3
VCC + 0.3
V
–2
+2
kV
Human body model (all pins)
–8
+8
kV
Human body model (PB and SR)
VESD
Electrostatic protection
VESD
Electrostatic protection
–1000
+1000
V
Charged device model
VESD
Electrostatic protection
–200
+200
V
Machine model
VESD
Point discharge on PB and SR inputs
–8
+8
kV
IEC61000-4-2
VESD
Air discharge on PB and SR inputs
–15
+15
kV
IEC61000-4-2
Operating ambient temperature
–40
+85
°C
Storage temperature
–45
+150
°C
Lead solder temperature for 10 seconds
+260
°C
Thermal resistance (junction to ambient)
+132.4
°C/W
TA
TSTG
TSLD
(1)
θ JA
1. Reflow at peak temperature of 260°C. The time above 255°C must not exceed 30 seconds.
38/51
Doc ID 15453 Rev 7
STM6600 - STM6601
7
DC and AC characteristics
DC and AC characteristics
This section summarizes the operating measurement conditions and the DC and AC
characteristics of the device. The parameters in the DC and AC characteristics tables that
follow are derived from tests performed under the measurement conditions summarized in
Table 4. Designers should check that the operating conditions in their circuit match the
operating conditions when relying on the quoted parameters.
Table 4.
Operating and AC measurement conditions
Parameter
Condition
Unit
VCC supply voltage
1.6 to 5.5
V
Ambient operating temperature (TA)
–40 to 85
°C
≤_5
ns
Input rise and fall times
Table 5.
Symbol
VCC
DC and AC characteristics
Parameter
Test condition(1)
Supply voltage
Min.
1.6
VCC = 3.6 V, no load
ICC
VTH+
Supply current
Threshold hysteresis (see
Table 10 for detailed listing)
VTH–
Forced power-off voltage
(see Table 10 for detailed
listing)
tTH–
Undervoltage detection to
INT delay
Max.
Unit
5.5
V
8
µA
1
µA
2.40
2.50
2.60
3.00
3.10
3.20
3.20
3.30
3.40
3.29
3.40
3.51
3.39
3.50
3.61
V
200
mV
500
VTH+ – VHYST
VCC ≥ 2.0 V
Blanking period (see
tON_BLANK Table 10 for detailed
listing)(3)
RST assertion to EN (EN)
assertion delay during
power-up
6
Standby mode, enable
deasserted, VCC = 3.6 V
Power-on lockout voltage
(see Table 10 for detailed
listing)
VHYST
Typ.(2)
VCC = 3.6 V
Doc ID 15453 Rev 7
V
20
32
44
1.4
2.2
3.0
5.6
8.8
12.0
11.2
17.6
24.0
100
ms
s
ns
39/51
DC and AC characteristics
Table 5.
Symbol
STM6600 - STM6601
DC and AC characteristics (continued)
Parameter
Test condition(1)
Min.
Typ.(2)
Max.
Unit
0.99
V
PB
VIL
Input low voltage
VCC ≥ 2.0 V, enable asserted
VIH
Input high voltage
VCC ≥ 2.0 V, enable asserted
tDEBOUNCE Debounce period
RPB
Internal pull-up resistor
VIL
Input low voltage
VIH
Input high voltage
1.05
V
VCC ≥ 2.0 V
20
32
44
ms
VCC = 5.5 V, input asserted
65
100
135
kΩ
0.99
V
SR
1.05
tDEBOUNCE Debounce period
RSR(4)
Internal pull-up resistor
VCC = 5.5 V, input asserted
Output low voltage
VCC = 2 V, ISINK = 1 mA,
PBOUT asserted
PBOUT leakage current
VPBOUT = 3 V, PBOUT open
drain
Output low voltage
VCC = 2 V, ISINK = 1 mA,
VCCLO asserted
VCC LO leakage current
VVCCLO = 3 V, VCCLO open
drain
VIL
Input low voltage
VCC ≥ 2.0 V
VIH
Input high voltage
VCC ≥ 2.0 V
V
20
32
44
ms
65
100
135
kΩ
0.3
V
+0.1
µA
0.3
V
+0.1
µA
0.99
V
PBOUT
VOL
–0.1
VCCLO
VOL
–0.1
PSHOLD
Glitch immunity
PSHOLD leakage current
1.05
1
VPSHOLD = 0.6 V
V
80
–0.1
PSHOLD to enable
propagation delay
Pull-down resistor
RPSHOLD connected internally during
power-up
40/51
VPSHOLD = 5.5 V
Doc ID 15453 Rev 7
195
300
µs
0.1
µA
30
µs
405
kΩ
STM6600 - STM6601
Table 5.
Symbol
DC and AC characteristics
DC and AC characteristics (continued)
Parameter
Test condition(1)
Min.
Typ.(2)
Max.
Unit
100
150
200
nA
CSRD
ISRD
C SRD charging current
VSRD
C SRD voltage threshold
VCC = 3.6 V, load on VREF pin
100 kΩ and mandatory 1 µF
capacitor, TA = 25 °C
1.5
V
tSRD
Additional Smart Reset™
delay time
External CSRD connected
10
s/µF
VOL
Output low voltage
VCC = 2 V, ISINK = 1 mA,
enable asserted
VOH(5)
Output high voltage
VCC = 2 V, ISOURCE = 1 mA,
enable asserted
EN, EN
tEN_OFF(6) enable off to enable on
VCC ≥ 2.0 V
0.3
V
VCC – 0.3
40
EN, EN leakage current
VEN = 2 V, enable open drain
VOL
Output low voltage
VCC = 2 V, ISINK = 1 mA,
RST asserted
tREC
RST pulse width
VCC ≥ 2.0 V
240
RST leakage current
VRST = 3V
–0.1
Output low voltage
VCC = 2 V, ISINK = 1 mA,
INT asserted
Minimum INT pulse width
VCC ≥ 2.0 V
INT leakage current
VINT = 3 V
–0.1
1.5 V voltage reference
VCC = 3.6 V, load on VREF pin
100 kΩ and mandatory 1 µF
capacitor, TA = 25 °C
1.485
–1%
V
64
–0.1
88
ms
+0.1
µA
0.3
V
480
ms
+0.1
µA
0.3
V
44
ms
+0.1
µA
1.515
+1%
V
RST
360
INT
VOL
tINT_Min
20
32
VREF
VREF
1.5
1. Valid for ambient operating temperature: TA = –40 to 85 °C; VCC = 1.6 V to 5.5 V (except where noted).
2. Typical values are at TA = +25 °C.
3. This blanking time allows the processor to start up correctly (see Figure 7, 8, 9, 10, 11, 12).
4. The internal pull-up resistor connected to the SR input is optional (see Table 10 for detailed device options).
5. Valid for push-pull only.
6. Minimal delay between enable off and enable on allows the application to power down properly. PB is ignored during this
period.
Doc ID 15453 Rev 7
41/51
Package mechanical data
8
STM6600 - STM6601
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
42/51
Doc ID 15453 Rev 7
STM6600 - STM6601
Package mechanical data
Figure 41. TDFN12 (2 x 3 mm) package outline
D
A
B
INDEX AREA
0.10 C 2x
E
(D/2xE/2)
0.10 C
TOP VIEW
A
A1
0.10 C
C
SEATING
PLANE
SIDE VIEW
0.08 C
e
b
1
6
12
7
0.10
C A B
PIN#1 ID
INDEX AREA
L
(D/2xE/2)
BOTTOM VIEW
8070542_A
Table 6.
TDFN12 (2 x 3 mm) package mechanical data
mm
inches
Symbol
Min.
Typ.
Max.
Min.
Typ.
Max.
A
0.70
0.75
0.80
0.028
0.030
0.031
A1
0.00
0.02
0.05
0.000
0.001
0.002
b
0.15
0.20
0.25
0.006
0.008
0.010
D
3.00 BSC
0.118
E
2.00 BSC
0.079
e
0.50
0.020
L
0.45
0.55
0.65
Doc ID 15453 Rev 7
0.018
0.022
0.026
43/51
Package mechanical data
STM6600 - STM6601
Figure 42. TDFN12 (2 x 3 mm) recommended footprint
X
X
X X
X
X
X
X
$IMENSIONS MM
INCHES !-
Note:
44/51
Drawing not to scale.
Doc ID 15453 Rev 7
STM6600 - STM6601
Package mechanical data
Figure 43. Carrier tape for TDFN12 (2 mm x 3 mm) package
P0
E
P2
D
T
A0
F
TOP COVER
TAPE
W
B0
P1
CENTER LINES
OF CAVITY
K0
USER DIRECTION OF FEED
AM03073v1
Table 7.
Carrier tape dimensions for TDFN12 (2 mm x 3 mm) package
Package
W
D
TDFN12
12.00
±0.30
1.50
+0.10/
–0.00
E
P0
P2
F
1.75
4.00
2.00
5.50
±0.10 ±0.10 ±0.10 ±0.05
A0
B0
K0
P1
T
2.30
±0.10
3.20
±0.10
1.10
±0.01
4.00
±0.10
0.30
±0.05
Doc ID 15453 Rev 7
Unit
Bulk
Qty.
mm 3000
45/51
Part numbering
STM6600 - STM6601
9
Part numbering
Table 8.
STM6600 ordering information scheme
Example:
STM660
0
F
Q
2
4
DM
6
Device type
STM660
Startup process
0: PB must be held low until the PSHOLD confirmation
Input and output types(1)
A: active high EN output, long push asserts RST, pull-up on SR
E: active high EN output, long push asserts RST, no resistor on SR
F: active low EN output, long push asserts RST, no resistor on SR
G: active high EN output, long push deasserts EN, no resistor on SR
H: active low EN output, long push deasserts EN, no resistor on SR
VTH+ threshold voltage(1)
A: 2.50 V
Q: 3.30 V
S: 3.40 V
U: 3.50 V
VHYST voltage hysteresis(1)
2: 200 mV
5: 500 mV
tON_BLANK blanking period(1)
2: 1.4 s (min.)
4: 5.6 s (min.)
5: 11.2 s (min.)
Package
DM: TDFN12
Temperature range
6: –40 °C to +85 °C
Shipping method
E: ECOPACK® package, tubes
F: ECOPACK® package, tape and reel
1. Other options are offered. Minimum order quantities may apply. Please contact local ST sales office for availability.
46/51
Doc ID 15453 Rev 7
F
STM6600 - STM6601
Table 9.
Part numbering
STM6601 ordering information scheme
Example:
STM660
1
G
U
2
B
DM
6
F
Device type
STM660
Startup process
1: PB can be released before the PSHOLD confirmation
Input and output types(1)
A: active high EN output, long push asserts RST, pull-up on SR
B: active low EN output, long push asserts RST, pull-up on SR
C: active high EN output, long push deasserts EN, pull-up on SR
D: active low EN output, long push deasserts EN, pull-up on SR
G: active high EN output, long push deasserts EN, no resistor on SR
VTH+ threshold voltage(1)
M: 3.10 V
Q: 3.30 V
S: 3.40 V
U: 3.50 V
VHYST voltage hysteresis(1)
2: 200 mV
tON_BLANK blanking period(1)
B: 1.4 s (min.)
D: 5.6 s (min.)
Package
DM: TDFN12
Temperature range
6: –40 °C to +85 °C
Shipping method
E: ECOPACK® package, tubes
F: ECOPACK® package, tape and reel
1. Other options are offered. Minimum order quantities may apply. Please contact local ST sales office for availability.
Doc ID 15453 Rev 7
47/51
Product selector
STM6600 - STM6601
10
Product selector
Table 10.
STM6600 product selector
Full part number
EN or
EN(1)
Internal Power-on Forced tON_BLANK tON_BLANK
After
resistor lockout power-off
Top
(s)
(s)
long
(3)
voltage
on
SR
voltage
marking
at startup
at reset
push(2)
VTH+ (V)
VTH- (V)
input
(min.)
(min.)
STM6600AS24DM6F
EN
RST
pull-up
3.40
3.20
5.6
5.6
pyww
AS24
STM6600ES24DM6F(4)
EN
RST
—
3.40
3.20
5.6
5.6
pyww
ES24
STM6600FQ24DM6F(4)
EN
RST
—
3.30
3.10
5.6
5.6
pyww
FQ24
STM6600GS22DM6F(4)
EN
EN
—
3.40
3.20
1.4
—
pyww
GS22
STM6600GS25DM6F(4)
EN
EN
—
3.40
3.20
11.2
—
pyww
GS25
STM6600GU22DM6F(4)
EN
EN
—
3.50
3.30
1.4
—
pyww
GU22
STM6600HA55DM6F(4)
EN
EN
—
2.50
2.00
11.2
—
pyww
HA55
STM6600HQ25DM6F(4)
EN
EN
—
3.30
3.10
11.2
—
pyww
HQ25
STM6600HU25DM6F(4)
EN
EN
—
3.50
3.30
11.2
—
pyww
HU25
1. EN (or EN) output is push-pull. RST, INT, PBOUT and VCCLO outputs are open drain.
2. After tSRD expires through long push, either device reset (RST) will be activated for tREC (240 ms min.) or the EN (or EN)
pin will be deasserted. The additional Smart Reset™ delay time, tSRD , can be adjusted by the user at 10 s/µF (typ.) by
connecting the external capacitor to the CSRD pin.
3. Where “p” = assembly plant, “y” = assembly year (0 to 9) and “ww” = assembly work week (01 to 52).
4. Please contact local ST sales office for availability.
48/51
Doc ID 15453 Rev 7
STM6600 - STM6601
Table 11.
Product selector
STM6601 product selector
Full part number
EN or
EN(1)
Internal Power-on
Forced tON_BLANK tON_BLANK
After
Top
resistor lockout power-off
(s)
(s)
long
marking(3)
voltage
on SR
voltage at startup
at
reset
(2)
push
VTH+ (V)
VTH- (V)
input
(min.)
(min.)
STM6601AQ2BDM6F
EN
RST
pull-up
3.30
3.10
1.4
1.4
pyww
AQ2B
STM6601AU2DDM6F
EN
RST
pull-up
3.50
3.30
5.6
5.6
pyww
AU2D
STM6601BM2DDM6F
EN
RST
pull-up
3.10
2.90
5.6
5.6
pyww
BM2D
STM6601BS2BDM6F
EN
RST
pull-up
3.40
3.20
1.4
1.4
pyww
BS2B
STM6601CM2DDM6F
EN
EN
pull-up
3.10
2.90
5.6
—
pyww
CM2D
STM6601CQ2BDM6F
EN
EN
pull-up
3.30
3.10
1.4
—
pyww
CQ2B
STM6601DS2BDM6F
EN
EN
pull-up
3.40
3.20
1.4
—
pyww
DS2B
STM6601GU2BDM6F(4)
EN
RST
—
3.50
3.30
5.6
5.6
pyww
GU2B
1. EN (or EN) output is push-pull. RST, INT, PBOUT and VCCLO outputs are open drain.
2. After tSRD expires through long push, either device reset (RST) will be activated for tREC (240 ms min.) or the EN (or EN) pin
will be deasserted. The additional Smart Reset™ delay time, tSRD, can be adjusted by the user at 10 s/µF (typ.) by
connecting the external capacitor to the CSRD pin.
3. Where “p” = assembly plant, “y” = assembly year (0 to 9) and “ww” = assembly work week (01 to 52).
4. Please contact local ST sales office for availability.
Doc ID 15453 Rev 7
49/51
Revision history
11
Revision history
Table 12.
50/51
STM6600 - STM6601
Document revision history
Date
Revision
Changes
04-Mar-2009
1
Initial release.
05-Jun-2009
2
Updated text in Section 2, Section 3, Figure 11, 12; updated Figure 1, 7, 9,
14, 18, 19, 43, Table 3, 5, 8, 9, 10; added Figure 8, 10, Table 7;
reformatted document.
23-Jul-2009
3
Updated text in Features, Table 1, 8, 9, and 10; reformatted document.
22-Oct-2009
4
Updated Section 2, Table 5, Table 10, Figure 1, 7, 8, 9, 10, 11, 12, 14, 18,
title of Section 10; added Section 5: Typical operating characteristics
(Figure 23 through 40); document status upgraded to full datasheet.
25-Jan-2010
5
Updated Figure 6, Section 2, Table 5; textual update to “Smart Reset™”.
13-Apr-2010
6
Updated Figure 1, 6, 7, 8, 9, 10, 11, 12, 13, Section 2, Section 3, Table 3,
5, 8, 9, 10.
07-Jun-2010
7
Reformatted Figure 1 and Figure 42, corrected typo in Section 3, added
option A to Table 8, updated Table 10 and separated Table 10 to Table 10
and Table 11.
Doc ID 15453 Rev 7
STM6600 - STM6601
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 15453 Rev 7
51/51