TI TAS5015PFBG4

TAS5015
SLES017 – SEPTEMBER 2001
TRUE DIGITAL AUDIO AMPLIFIER
TAS5015 DIGITAL AUDIO PWM PROCESSOR
FEATURES
D TAS5015 Plus Discrete Back-End TDAA
D
D
D
D
D
D
D
D
D
D
DESCRIPTION
System — High-Quality Digital Audio
Amplification
112-dB Dynamic Range (TAS5015 Device)
THD+N < 0.01%
Power Efficiency Is 90% into 8-Ω Load
16-, 20-, or 24-Bit Input Data
44.1-kHz, 48-kHz, 88.2-kHz, 96-kHz, 176.4-kHz,
192-kHz Sampling Rates
Economical 48-Pin TQFP Package
External PLL
3.3-V Power Supply
Mute
Clicks and Pops Reduction (Patent Pending)
APPLICATIONS
D High-Performance Digital Amplification For:
– Integrated Amplifiers
– AV Receiver
– Car Audio
Digital Audio
• Digital Audio
Processor
Left
Discrete
Back-End
L-C
Filter
Right
Discrete
Back-End
L-C
Filter
TAS5015
• DSP
• S/PDIF
• 1394
• Volume
• EQ
• DRC
• Bass
• Treble
The true digital audio amplifier (TDAA) is a new
paradigm in digital audio. One TDAA system consists of
the TAS5015 PCM-PWM modulator device plus a
discrete back-end TDAA power output. This system
accepts a serial PCM digital audio stream and converts
it to a 3.3-V PWM audio stream (TAS5015). The
discrete back-end TDAA then provides a large-signal
PWM output. This digital PWM signal is then
demodulated, providing power output for driving
loudspeakers. This patented technology provides
low-cost, high-quality, high-efficiency digital audio
applicable to many audio systems developed for the
digital age. The TAS5015 is an innovative,
cost-effective,
high-performance
24-bit
stereo
PCM-PWM modulator based on Equibit technology.
The TAS5015 has a wide variety of serial input options
including right-justified (16, 20, or 24 bits), IIS (16, 20,
or 24 bits), left-justified (16 bits), or DSP (16 bits) data
formats. It is fully compatible with AES standard
sampling rates (Fs) of 44.1 kHz, 48 kHz, 88.2 kHz, 96
kHz, 176.4 kHz, and 192 kHz. The TAS5015 also
provides a de-emphasis function for 44.1-kHz and
48-kHz sampling rates.
• Serial Audio Input Port
• External PLL
• Equibit Modulator
• Up to 192-kHz Sampling
• H-Bridges
Power Devices
• Improved Performance
From TAS5100
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Equibit is a trademark of Toccata Technology ApS, Denmark.
Copyright  2001, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
www.ti.com
1
TAS5015
SLES017 – SEPTEMBER 2001
terminal assignments
AVDD1
AVSS1
NC
NC
AVSS1
DEM_EN
DEM_SEL
FTEST
STEST
DBSPD
MUTE
DVSS3_L
48-Pin TQFP PACKAGE
(TOP VIEW)
48 47 46 45 44 43 42 41 40 39 38 37
MCLK_IN
AVDD2
NC
NC
AVSS2
HFCLK
RESET
PDN
VALID_R
M_S
NC
DVDD1
1
36
2
35
3
34
4
33
5
32
6
31
7
30
8
29
9
28
10
27
11
26
12
25
DVDD3_L
PWM_AP_L
PWM_AM_L
PWM_BM_L
PWM_BP_L
DVDD2
DVSS2
PWM_AP_R
PWM_AM_R
PWM_BM_R
PWM_BP_R
DVDD3_R
DVSS1
DVDD1
DVSS1
MCLK_OUT
SCLK
LRCLK
SDIN
MOD2
MOD1
MOD0
VALID_L
DVSS3_R
13 14 15 16 17 18 19 20 21 22 23 24
NC – No internal connection
references
D True Digital Audio Amplifier TAS5100 PWM Power Output Stage – Texas Instruments publication SLLS419
D Design Considerations for TAS5000/TAS5110 True Digital Audio Power Amplifiers – Texas Instruments
publication SLAA117
D Digital Audio Measurements – Texas Instruments publication SLAA114
D PowerPAD Thermally Enhanced Package – Texas Instruments publication SLMA002
PowerPAD is a trademark of Texas Instruments.
2
www.ti.com
TAS5015
SLES017 – SEPTEMBER 2001
MCLK_OUT
VALID_R
VALID_L
HFCLK
MCLK_IN
functional block diagram
Clock
Generator
LRCLK
Serial
Audio
Port
SCLK
Digital
Interpolation
Filter
Equibit
Modulator
PWM_AP_L
PWM_AM_L
PWM_BP_L
PWM_BM_L
Buffer
PWM_AP_R
PWM_AM_R
PWM_BP_R
PWM_BM_R
SDIN
Control Section
DVDD1
DVSS1
DVDD2
DVSS2
DVDD3_L
DVSS3_L
DVDD3_R
DVSS3_R
AVDD1
AVSS1
AVDD2
AVSS2
STEST
DBSPD
M_S
FTEST
PDN
MUTE
RESET
DEM_EN
DEM_SEL
MOD2
MOD1
MOD0
Audio Port
Configuration
AVAILABLE OPTIONS
PACKAGE
TA
0°C to 70°C
TAS5015PFB
–40°C to 85°C
TAS5015IPFB
NOTE: These packages are available taped and reeled. Add R suffix
to ordering number (e.g., TAS5015PFBR).
www.ti.com
3
TAS5015
SLES017 – SEPTEMBER 2001
Terminal Functions
TERMINAL
NAME
AVDD1
I/O
DESCRIPTION
48
I
Analog supply
AVDD2
2
I
Analog supply
AVSS1
44, 47
I
Analog ground
AVSS2
5
I
Analog ground
DBSPD
39
I
Indicates sample rate is double speed (88.2 kHz or 96 kHz), active high
DEM_EN
43
I
De-emphasis enable, active high
DEM_SEL
42
I
De-emphasis select (0 = 44.1 kHz, 1 = 48 kHz)
DVDD1
12, 14
I
Digital voltage supply for logic
DVDD2
31
I
Digital voltage supply for PWM reclocking
DVDD3_L
36
I
Digital voltage supply for PWM output (left)
DVDD3_R
25
I
Digital voltage supply for PWM output (right)
DVSS1
13, 15
I
Digital ground for logic
DVSS2
30
I
Digital ground for PWM reclocking
DVSS3_L
37
I
Digital ground for PWM output (left)
DVSS3_R
24
I
Digital ground for PWM output (right)
FTEST
41
I
Tied to DVSS1 for normal operation
HFCLK
6
I
External PLL clock input
LRCLK
18
I/O
MCLK_IN
1
I
MCLK input
MCLK_OUT
16
O
Buffered system clock output if M_S = 1; otherwise set to 0
MOD0
22
I
Serial interface selection pin, bit 0
MOD1
21
I
Serial interface selection pin, bit 1
MOD2
20
I
Serial interface selection pin, bit 2 (MSB)
M_S
10
I
Master/slave, master=1, slave=0
MUTE
38
I
Muted signal = 0, normal mode = 1
NC
4
NO.
3, 4, 11, 45,
46
Left/right clock (input when M_S = 0; output when M_S = 1)
No connection
PDN
8
I
Power down, active low
PWM_AM_L
34
O
PWM left output A (differential –)
PWM_AM_R
28
O
PWM right output A (differential –)
PWM_AP_L
35
O
PWM left output A (differential +)
PWM_AP_R
29
O
PWM right output A (differential +)
PWM_BM_L
33
O
PWM left output B (differential –)
PWM_BM_R
27
O
PWM right output B (differential –)
PWM_BP_L
32
O
PWM left output B (differential +)
PWM_BP_R
26
O
PWM right output B (differential +)
RESET
7
I
Reset (active low)
SCLK
17
I/O
SDIN
19
I
Stereo serial audio data input
STEST
40
I
Tied to DVSS1 for normal operation
VALID_L
23
O
PWM left outputs valid (active high)
VALID_R
9
O
PWM right outputs valid (active high)
Shift clock (input when M_S = 0, output when M_S = 1)
www.ti.com
TAS5015
SLES017 – SEPTEMBER 2001
functional description
serial audio port
The serial audio port consists of a shift clock (SCLK pin), a left/right frame synchronization clock (LRCLK pin),
and a data input (SDIN pin). The serial audio port supports standard serial PCM formats (Fs = 44.1-kHz, 48-kHz,
88.2-kHz, 96-kHz, 176.4-kHz, or 192-kHz stereo). See the serial interface formats section.
system clocks—master mode and slave mode
The TAS5015 allows multiple system clocking schemes. Master mode indicates that the TAS5015 provides
system clocks to other parts of the system (M_S=1). Audio system clocks of frequency 128 Fs MCLK_OUT
(quad speed), 64 Fs SCLK, and Fs LRCLK are output from this device when it is configured in master mode.
Slave mode indicates that a system master other than the TAS5015 provides system clocks (LRCLK, SCLK,
and MCLK_IN) to the TAS5015 (M_S = 0). The TAS5015 operates with LRCLK and SCLK synchronized to
MCLK. The TAS5015 does not require any specific phase relationship between LRCLK and MCLK, but there
must be synchronization. In the slave mode, MCLK_OUT is driven low. Table 1 shows all the possible master
and slave modes.
sampling frequency
The normal sampling frequency is either 11.2896 MHz (Fs = 44.1 kHz) or 12.288 MHz (Fs = 48 kHz). Twice the
normal sampling frequency can be selected by using the DBSPD pin which allows usage of Fs = 88.2 kHz or
Fs = 96 kHz. In the double-speed slave mode (DBSPD = 1, M_S = 0), the external clock input is either
22.5796 MHz (Fs = 88.2 kHz) or 24.576 MHz (Fs = 96 kHz). Table 1 explains the proper clock selection.
Table 1. External Clock and External PLL Functions
MCLK_IN
(MHz)
HFCLK
(MHz)
SCLK
(MHz)
LRCLK
(KHz)
MCLK_OUT
(MHz)
–
90 3168
90.3168
2 8224
2.8224
44 1
44.1
11 2896
11.2896
–
98 304
98.304
3 072
3.072
48
12 288
12.288
0
–
90.3168
5.6448
88.2
22.5792
0
0
–
98.304
6.144
96
24.576
0
0
1
–
90.3168
11.2896
176.4
22.5792
1
0
0
1
–
98.304
12.288
192
24.576
External PLL, slave, normal sspeed
eed
(see Notes 3, 4, and 5)
0
0
0
0
1
0
11 2896
11.2896
90 3168
90.3168
2 8224
2.8224
44 1
44.1
11 2896
11.2896
External PLL, slave, normal sspeed
eed
(see Notes 3, 4, and 5)
1
1
0
0
0
0
12 288
12.288
98 304
98.304
3 072
3.072
48
12 288
12.288
DESCRIPTION
M_S
DBSPD
DEM_EN
DEM_SEL
External PLL, master, normal
speed (see Notes 1 and 2)
1
0
0
0
1
0
External PLL, master, normal
speed (see Notes 1 and 2)
1
0
1
1
0
0
External PLL, master, double
speed (see Notes 1 and 2)
1
1
0
External PLL, master, double
speed (see Note 1 and 2)
1
1
External PLL, master, quad speed
(see Notes 1 and 2)
1
External PLL, master, quad speed
(see Notes 1 and 2)
NOTES: 1.
2.
3.
4.
5.
SCLK and LRCLK are outputs
MCLK_IN tied LOW
External MCLK connected to MCLK_IN input
SCLK and LRCLK are inputs
MCLK_OUT is a buffered version of the external MCLK input
www.ti.com
5
TAS5015
SLES017 – SEPTEMBER 2001
functional description (continued)
Table 1. External Clock and External PLL Functions (Continued)
M_S
DBSPD
DEM_EN
DEM_SEL
MCLK_IN
(MHz)
HFCLK
(MHz)
SCLK
(MHz)
LRCLK
(kHz)
MCLK_OUT
(MHz)
External PLL, slave, double speed
(see Notes 3, 4, and 5)
0
1
0
0
22.5792
90.3168
5.6448
88.2
22.5792
External PLL, slave, double speed
(see Notes 3, 4, and 5)
0
1
0
0
24.576
98.304
6.144
96
24.576
External PLL, slave, quad speed
(see Notes 3, 4, and 5)
0
0
0
0
22.5792
90.3168
11.2896
176.4
22.5792
External PLL, slave, quad speed
(see Notes 3, 4, and 5)
0
0
0
0
24.576
98.304
12.288
192
24.576
DESCRIPTION
NOTES:
3. External MCLK connected to MCLK_IN input
4. SCLK and LRCLK are inputs
5. MCLK_OUT is a buffered version of the external MCLK input
external PLL
For the highest system performance, an external PLL must be used with the TAS5015. For normal-speed mode,
the external PLL input (HFCLK) must be 2048 Fs, for double-speed mode HFCLK must be 1024 Fs, and for
quad-speed mode HFCLK must be 512 Fs.
digital interpolation filter
The 24-bit high-performance linear phase FIR interpolation filter up-samples the input digital data at a rate of
two times (quad-speed mode = 176.4 kHz or 192 kHz), four times (double-speed mode = 88.2 kHz or 96 kHz),
or eight times (normal mode = 44.1 kHz or 48 kHz) the incoming sample rate. This filter provides low pass-band
ripple and optimized time domain transient response for accurate music reproduction.
digital PWM modulator
The interpolation filter output is sent to the digital PWM modulator. This modulator consists of a highperformance fourth order digital-noise shaper and a PCM-to-PWM converter. Following the noise shaper, the
PCM signal is fed into a low distortion PCM-to-PWM conversion block, buffered, and output from the chip. The
modulation scheme is based on a 2-state control of the H-bridge output.
control, status, and operational modes
The TAS5015 control section consists of several control-input pins. Three serial mode pins (MOD0, MOD1, and
MOD2) are provided to select various serial data formats. During normal operating conditions if any of the
MOD0, MOD1, or MOD2 pins changes state, a reset sequence is initiated. Also provided are separate
power-down (PDN), reset (RESET), and mute (MUTE) pins.
power up
At power up, the VALID_L and VALID_R pins are asserted low and the PWM outputs go to the hard mute state
in which the P outputs are held low and the M outputs are held high. Following initialization, the TAS5015 comes
up in the operational state (differential PWM audio). There are two cases of power-up timing. The first case is
shown in Figure 1 with RESET preceding PDN. The second case is shown in Figure 2 with PDN preceding
RESET.
6
www.ti.com
TAS5015
SLES017 – SEPTEMBER 2001
functional description (continued)
RESET
PDN
Initialization Time = 100 ms max
VALID_L
VALID_R
Figure 1. Power-Up Timing (RESET Preceding PDN)
Greater Than 16 MCLK Periods
RESET
PDN
Initialization Time = 5 ms max
VALID_L
VALID_R
Figure 2. Power-Up Timing (PDN Preceding RESET)
reset
The reset signal for the TAS5015 must be applied whenever toggling the M_S, DBSPD signal. This reset is
asynchronous. See Figure 3 for reset timing. To initiate the reset sequence the RESET pin is asserted low. As
long as the pin is held low the chip is in the reset state. During this reset time, the PWM outputs are hard-muted
(P-outputs held low and M-outputs held high) and the PWM outputs valid pins (VALID_L. VALID_R) are held
low. Assuming PDN is high, the rising edge of the reset pulse begins chip initialization. After the initialization
time, the TAS5015 begins normal operation.
RESET
5 ms max
VALID_L
Initialization
Normal
Operation
VALID_R
Normal Operation
PDN
Figure 3. Reset Timing
power down
Note that power down is an asynchronous operation. To place the device in total power-down mode, both
RESET and PDN must be held low. As long as these pins are held low, the chip is in the power-down state and
the PWM outputs are hard muted with the P outputs held low and the M outputs held high. To place the device
back into normal mode, see the power up section.
NOTE:
In order for the dynamic logic to be properly powered down, the clocks should not be stopped before
the PDN pin goes low. Otherwise, the device may drain additional supply current.
www.ti.com
7
TAS5015
SLES017 – SEPTEMBER 2001
functional description (continued)
VALID
Normal Operation
Normal
Operation
Initialization
Chip
Power-Down
PDN and RESET
Figure 4. Power-Down Timing
mute
The TAS5015 provides a mute function that is used when the MUTE pin is asserted low. See Table 2 for mute
description. This mute is a quiet mute; that is, the mute is accomplished by outputting a zero value waveform
in which both sides of the differential PWM outputs have a 50% duty cycle (see Figure 5 for mute timing).
Table 2. Mute Description
MUTE
P OUTPUTS
M OUTPUTS
DESCRIPTION
0
50% duty cycle
50% duty cycle
Mute
1
DATA
DATA
Normal operation
10 µs max
MUTE
5 ms max
Initialization
VALID_L
VALID_R
PWM Outputs
50–50 Duty Cycle
(P, M Complementary)
Inactive State
Normal State
(P, M Complementary)
Figure 5. Mute Timing
double speed
Double-speed mode is used to support sampling rates of 88.2 kHz and 96 kHz. In order to put the TAS5015 in
double-speed mode with the device in normal operating conditions, the RESET pin must be held low while
switching the DBSPD pin high. After the RESET pin is brought high again, a reset sequence takes place. If the
change is at power up, a power-up sequence is originated.
quad speed
Quad-speed mode is used to support sampling rates of 176.4 kHz and 192 kHz. In order to put the TAS5015
in quad-speed slave mode, M_S and DBPSB pins are brought low. Quad-speed mode is then automatically
detected due to the fact that it is the only mode in which MCLK_IN is 128 Fs. DEM_SEL must be set to low when
operating in the quad-speed slave mode. For quad-speed master mode M_S = 1, DBSPD = 0, DEM_SEL = 1,
and DEM_EN = 0.
8
www.ti.com
TAS5015
SLES017 – SEPTEMBER 2001
functional description (continued)
de-emphasis filter
Response – dB
For audio sources that have been preemphasized, a precision 50 µs/15 µs de-emphasis filter is provided to
support the sampling rates of 44.1 kHz and 48 kHz. Pins DEM_SEL and DEM_EN select the de-emphasis
functions. See Figure 6 for a graph showing the de-emphasis filtering characteristics. See Table 3 for
de-emphasis selection.
0
De-emphasis
–10
3.18 (50 µs)
10.6 (15 µs)
f – Frequency – kHz
Figure 6. De-Emphasis Filter Characteristics
de-emphasis selection
De-emphasis selection is accomplished by using the DEM_SEL and DEM_EN pins. See Table 3 for
de-emphasis selection description.
Table 3. De-Emphasis Selection
DEM_SEL
DEM_EN
DESCRIPTION
0
0
De-emphasis disabled
0
1
De-emphasis enabled for Fs = 44.1 kHz
1
1
De-emphasis enabled for Fs = 48 kHz
1
0
Disallowed state. Do not use.
error status reporting (VALID_L and VALID_R)
The following is a list of the error conditions that will cause the VALID_L and VALID_R pins to be asserted low.
–
No clocks
–
Clock phase errors
When either of the above conditions is met, the VALID_L and VALID_R goes low and the PWM outputs go to
the hard mute state. If the error condition is removed, the TAS5015 is reinitialized and the VALID_L and VALID_R
pins are asserted high.
serial interface formats
The TAS5015 is compatible with eight different serial interfaces. Available interface options are IIS, right
justified, left justified, and DSP frame. Table 4 indicates how these options are selected using the MOD0, MOD1,
and MOD2 pins.
www.ti.com
9
TAS5015
SLES017 – SEPTEMBER 2001
functional description (continued)
Table 4. Hardware Selection of Serial Audio Modes
SERIAL INTERFACE
SDIN
MODE
MOD2 PIN
MOD1 PIN
MOD0 PIN
0
0
0
0
16-bit, MSB first; right justified
1
0
0
1
20-bit, MSB first; right justified
2
0
1
0
24-bit, MSB first; right justified
3
0
1
1
16-bit IIS
4
1
0
0
20-bit IIS
5
1
0
1
24-bit IIS
6
1
1
0
16-bit MSB first, left justified
7
1
1
1
16-bit DSP frame
The following figures illustrate the relationship between the SCLK, LRCLK, and the serial data I/O for the
different interface protocols. Note that there are always 64 SCLKs per LRCLK. The nondata bits are padded
with binary 0s.
MSB first, right-justified (for 16, 20, 24 bits)
SCLK
LRCLK = fs
SDIN
X
MSB
LSB
Left Channel
X
MSB
Right Channel
Figure 7. MSB First Right Justified
Note the following characteristics of this protocol.
10
–
Left channel is received when LRCLK is high.
–
Right channel is received when LRCLK is low.
–
SDIN is sampled at the rising edge of SCLK.
www.ti.com
LSB
TAS5015
SLES017 – SEPTEMBER 2001
functional description (continued)
IIS compatible serial format (for 16, 20, 24 bits)
SCLK
LRCLK = fs
X
SDIN
MSB
LSB
X
Left Channel
MSB
LSB
Right Channel
Figure 8. IIS Compatible Serial Format
Note the following characteristics of this protocol.
–
Left channel is received when LRCLK is low.
–
Right channel is received when LRCLK is high.
–
SDIN is sampled with the rising edge of the SCLK.
MSB left-justified serial interface format (for 16 bits)
SCLK
LRCLK = fs
SDIN
MSB
LSB
MSB
Left Channel
LSB
Right Channel
Figure 9. MSB Left-Justified Serial Interface Format
Note the following characteristics of this protocol.
–
Left channel is received when LRCLK is high.
–
Right channel is received when LRCLK is low.
–
SDIN is sampled at the rising edge of SCLK.
www.ti.com
11
TAS5015
SLES017 – SEPTEMBER 2001
functional description (continued)
DSP compatible serial interface format (for 16 bits)
SCLK
LRCLK = fs
SDIN
15
14
13
0
15
Left Channel
(MSB = 15)
14
13
0
Right Channel
(MSB = 15)
Figure 10. DSP Compatible Serial Interface Format
Note the following characteristic of this protocol.
–
Serial data is sampled with the falling edge of SCLK.
PWM Outputs
The TAS5015 is designed to be used with a discrete back-end. The TAS5015 PWM outputs provide differential
3.3-V square-wave signals. During normal operation these outputs represent the input PCM audio in the
pulse-width modulation scheme. In the hard-mute state the P outputs (PWM_AP_L, PWM_BP_L, PWM_AP_R,
and PWM_BP_R) are held low and the M outputs (PWM_AM_L, PWM_BM_L, PWM_AM_R, and PWM_BM_R)
are held high. In the quiet-mute state the differential PWM outputs have a 50% duty cycle.
absolute maximum ratings over operating free-air temperature (unless otherwise noted)†
Analog supply voltage range, AVDD1, AVDD2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 4.2 V
Digital power supply voltage, DVDD1, DVDD2, DVDD3_L, DVDD3_R . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 4.2 V
Digital input voltage, VI (see Note 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to DVDDX + 0.3 V
Operating free-air temperature, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
Storage temperature, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 V
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 6: DVDD1, DVDD2, DVDD3_L, DVDD3_R.
12
www.ti.com
TAS5015
SLES017 – SEPTEMBER 2001
recommended operating conditions, TA = 25°C,
DVDD1 = DVDD2 = DVDD3_L = DVDD3_R = 3.3 V ±10%, AVDD1 = AVDD2 = 3.3 V ±10%, Fs = 44.1 kHz
MIN
Supply voltage
Digital
DVDDX†
Analog
AVDDX§
Digital
Supply current
3
TYP
33
3.3
Operating
22
Power down‡
10
Operating
Analog
Power dissipation
Analog
UNIT
3
3.6
6
V
mA
µA
20
1
Power down‡
10
Operating
Digital
MAX
mA
59.4
Power down‡
6.6
Operating
3.3
Power down‡
33
µA
100
mW
µW
72
mW
µW
360
† DVDD1, DVDD2, DVDD3_L, DVDD3_R
‡ If the clocks are turned off
§ AVDD1, AVDD2
electrical characteristics, TA = 25°C, DVDD1 = DVDD2 = DVDD3_L = DVDD3_R = 3.3 V ±10%,
AVDD1 = AVDD2 = 3.3 V ±10%
static digital specifications
PARAMETER
VIH
VIL
High-level input voltage
VOH
VOL
High-level output voltage
TEST CONDITIONS
MIN
Low-level input voltage
Low-level output voltage
IO = –1 mA
IO = 4 mA
Input leakage current
TYP
MAX
UNIT
2
DVDD1
V
0
0.8
V
2.4
V
–10
0.4
V
10
µA
digital interpolation filter and PWM modulator, Fs = 44.1 kHz
PARAMETER
TEST CONDITIONS
MIN
Pass band
TYP
0
MAX
20
UNIT
kHz
±0.012
dB
24.1
kHz
Group delay
700
µS
PWM modulation index (gain)
0.93
dB
Pass-band ripple
Stop band
Stop-band attenuation
24.1 kHz to 152.3 kHz
50
dB
TAS5015/TAS5110 system performance measured at the speaker terminals
See the Design Consideration for TAS5000/TAS5100 True Digital Audio Power Amplifiers application note,
Texas Instruments literature number SLAA117 for values.
www.ti.com
13
TAS5015
SLES017 – SEPTEMBER 2001
switching characteristics, TA = 25°C,
DVDD1 = DVDD2 = DVDD3_L = DVDD3_R = AVDD1 = AVDD2 = 3.3 V ±10%
serial audio ports slave mode
PARAMETER
MIN
TYP
MAX
UNIT
12.288
MHz
f(SCLK)
tsu(SDIN)
SCLK frequency
SDIN setup time before SCLK rising edge
20
ns
th(SDIN)
f(LRCLK)
SDIN hold time from SCLK rising edge
10
ns
tsu(LRCLK)
LRCLK frequency
44.1
48
MCLK duty cycle
50%
SCLK duty cycle
50%
LRCLK duty cycle
50%
LRCLK edge setup before SCLK rising edge
192
20
kHz
ns
serial audio ports master mode, CL = 50 pF
PARAMETER
MIN
TYP
MAX
UNIT
t(MSD)
MCLK to SCLK
0
5
ns
t(MLRD)
MLCK to LRCLK
0
5
ns
DSP serial interface mode
PARAMETER
f(SCLK)
tw(FSHIGH)
MIN
Pulse duration, sync
1/(64×fs)
MAX
UNIT
12.288
MHz
ns
tsu(SDIN),
tsu(LRCLK)
SDIN and LRCLK setup time before SCLK falling edge
20
ns
th(SDIN),
th(LRCLK)
SDIN and LRCLK hold time from SCLK falling edge
10
ns
SCLK duty cycle
14
TYP
SCLK frequency
50%
www.ti.com
TAS5015
SLES017 – SEPTEMBER 2001
PARAMETER MEASUREMENT INFORMATION
SCLK
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
tsu(SDIN)
SDIN
th(SDIN)
Figure 11. Right-Justified, IIS, Left-Justified Serial Protocol Timing
SCLK
tsu(LRCLK)
LRCLK
NOTE: Serial data is sampled with the rising edge of SCLK (setup time = 20 ns and hold time = 10 ns)
Figure 12. Right, Left, and IIS Serial Mode Timing Requirement
SCLK
LRCLK
(Output)
t(MSD)
t(MLRD)
MCLK
(Output)
Figure 13. Serial Audio Ports Master Mode Timing
SCLK
th(LRCLK)
tsu(LRCLK)
LRCLK
tw(FSHIGH)
tsu(SDIN)
SDIN
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
th(SDIN)
Figure 14. DSP Serial Port Timing
www.ti.com
15
TAS5015
SLES017 – SEPTEMBER 2001
PARAMETER MEASUREMENT INFORMATION
SCLK
LRCLK
tw(FSHIGH)
64 SCLK
16-Bit Left Channel Data
SDIN
16-Bit Left Channel Data
32-Bit Ignore
16-Bit Left Channel Data
Figure 15. DSP Serial Port Expanded Timing
SCLK
SDIN
th(SDIN) = 10 ns
ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎ
tsu(SDIN) = 20 ns
NOTE: Serial data is sampled with the falling edge of SCLK (setup time = 20 ns and hold time = 10 ns)
Figure 16. DSP Absolute Timing Requirement
16
www.ti.com
TAS5015
SLES017 – SEPTEMBER 2001
APPLICATION INFORMATION
TAS5015
PWM_AP_L
PWM_AM_L
PWM_BP_L
PWM_BM_L
VALID_L
Discrete
Back-End
RESET
DEM_SEL
Audio
Source
Clock
Generator
3.3 V DIG
DEM_EN
DBSPD
SDIN
LRCLK
SCLK
MCLK_IN
PWM_AP_R
PWM_AM_R
PWM_BP_R
PWM_BM_R
VALID_R
MOD0
RESET
System
Controller
MOD1
MOD2
External
PLL
Discrete
Back-End
RESET
M_S
MUTE
PDN
HFCLK
FTEST
STEST
NOTE A: See the Design Consideration for TAS5000/TAS5100 True Digital Audio Power Amplifiers application note, Texas Instruments literature
number SLAA117 for values.
www.ti.com
17
TAS5015
SLES017 – SEPTEMBER 2001
MECHANICAL DATA
PFB (S-PQFP-G48)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
36
0,08 M
25
37
24
48
13
0,13 NOM
1
12
5,50 TYP
7,20
SQ
6,80
9,20
SQ
8,80
Gage Plane
0,25
0,05 MIN
0°–ā7°
1,05
0,95
Seating Plane
1,20 MAX
0,75
0,45
0,08
4073176 / B 10/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
18
www.ti.com
PACKAGE OPTION ADDENDUM
www.ti.com
18-Apr-2006
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TAS5015PFB
NRND
TQFP
PFB
48
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TAS5015PFBG4
ACTIVE
TQFP
PFB
48
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Mailing Address:
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2006, Texas Instruments Incorporated