MICROCHIP TC1265

TC1265
800 mA Fixed-Output CMOS LDO with Shutdown
Features
Description
•
•
•
•
•
•
•
The TC1265 is a fixed-output, high-accuracy (typically
±0.5%) CMOS low dropout regulator. Designed
specifically for battery-operated systems, the TC1265’s
CMOS construction eliminates wasted ground current,
significantly extending battery life. Total supply current
is typically 80 µA at full load (20 to 60 times lower than
in bipolar regulators).
Very Low Dropout Voltage
800 mA Output Current
High Output Voltage Accuracy
Standard or Custom Output Voltages
Overcurrent and Overtemperature Protection
SHDN Input for Active Power Management
ERROR Output Can Be Used as a Low Battery
Detector (SOIC only)
Applications
•
•
•
•
•
•
•
Key features of the TC1265 include ultra low noise
operation, very low dropout voltage (typically 450 mV
at full load) and fast response to step changes in load.
The TC1265 incorporates both overtemperature and
overcurrent protection. The TC1265 is stable with an
output capacitor of only 1 µF and has a maximum
output current of 800 mA. It is available in 8-Pin SOIC,
5-Pin TO-220 and 5-Pin DDPAK packages.
Battery-operated Systems
Portable Computers
Medical Instruments
Instrumentation
Cellular/GSM/PHS Phones
Linear Post-Regulators for SMPS
Pagers
Package Type
5-Pin TO-220
5-Pin DDPAK
Front View
VIN
VOUT
TC1265
SHDN
TC1265
C1
1 µF
1 2 3 4 5
1 2 3 4 5
SHDN
BYP
SHDN
GND
VIN
VOUT
GND
+
TC1265
VOUT
BYP
SHDN
GND
VIN
VOUT
VIN
Tab Is GND
Tab Is GND
Typical Application
8-Pin SOIC
VOUT
1
8
VIN
GND
2
7
NC
TC1265
 2004 Microchip Technology Inc.
NC
3
6
SHDN
BYPASS
4
5
ERROR
DS21376C-page 1
TC1265
1.0
ELECTRICAL
CHARACTERISTICS
Absolute Maximum Ratings †
Input Voltage .........................................................6.5V
Output Voltage.................. (VSS – 0.3V) to (VIN + 0.3V)
Power Dissipation................Internally Limited (Note 7)
Maximum Voltage on Any Pin ........VIN +0.3V to -0.3V
Operating Temperature Range...... -40°C < TJ < 125°C
Storage Temperature..........................-65°C to +150°C
† Notice: Stresses above those listed under "Maximum
Ratings" may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operation listings of this specification is not implied. Exposure
to maximum rating conditions for extended periods may affect
device reliability.
DC CHARACTERISTICS
Electrical Specifications: Unless otherwise indicated, VIN = VR + 1.5V, (Note 1), IL = 100 µA, CL = 3.3 µF,
SHDN > VIH, TA = +25°C. Boldface type specifications apply for junction temperatures of -40°C to +125°C.
Parameters
Input Operating Voltage
Maximum Output Current
Output Voltage
VOUT Temperature Coefficient
Sym
Min
Typ
Max
Units
VIN
2.7
—
6.0
V
—
—
mA
IOUTMAX
800
VOUT
VR – 2.5%
VR ± 0.5% VR + 2.5%
VR – 2%
VR ± 0.5%
VR + 3%
—
40
—
∆VOUT/∆T
Conditions
Note 2
VR ≥ 2.5V
V
VR = 1.8V
ppm/°C
Note 3
Line Regulation
∆VOUT/∆VIN
—
0.007
0.35
%
Load Regulation (Note 4)
∆VOUT/VOUT
-0.01
0.002
+0.01
%/mA
IL = 0.1 mA to IOUTMAX
Dropout Voltage (Note 5)
VIN–VOUT
—
20
30
mV
VR ≥ 2.5V, IL = 100 µA
—
50
160
IL = 100 mA
—
150
480
IL = 300 mA
—
260
800
IL = 500 mA
—
450
1300
IL = 800 mA
—
700
1000
VR = 1.8V, IL = 500 mA
—
890
1400
—
80
130
µA
Supply Current
IDD
(VR + 1V) ≤ VIN ≤ 6V
IL = 800 mA
SHDN = VIH, IL = 0
Shutdown Supply Current
ISHDN
—
0.05
1
µA
SHDN = 0V
Power Supply Rejection Ratio
PSRR
—
64
—
db
F ≤ 1 kHz
Output Short Circuit Current
Thermal Regulation
Output Noise
IOUTSC
—
1200
1400
mA
VOUT = 0V
∆VOUT/∆PD
—
0.04
—
V/W
Note 6
eN
—
260
—
nV/√Hz
IL = IOUTMAX, F = 10 kHZ
Note 1: VR is the regulator output voltage setting.
2: The minimum VIN has to justify the conditions: VIN ≥ VR + VDROPOUT and VIN ≥ 2.7V for IL = 0.1 mA to IOUTMAX.
6
3:
(V
–V
) – 10
OUTMAX
OUTMIN
TCV OUT = ------------------------------------------------------------------------V OUT × ∆T
4: Regulation is measured at a constant junction temperature using low duty cycle pulse testing. Load regulation is tested
over a load range from 0.1 mA to the maximum specified output current. Changes in output voltage due to heating effects
are covered by the thermal regulation specification.
5: Dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal value
measured at a 1.5V differential.
6: Thermal regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied,
excluding load or line regulation effects. Specifications are for a current pulse equal to ILMAX at VIN = 6V for T = 10 ms.
7: The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction temperature and the thermal resistance from junction-to-air (i.e., TA, TJ, θJA). Exceeding the maximum allowable power dissipation causes the device to initiate thermal shutdown. Please see Section 5.0 “Thermal Considerations” for more details.
8: Hysteresis voltage is referenced to VR.
DS21376C-page 2
 2004 Microchip Technology Inc.
TC1265
DC CHARACTERISTICS (CONTINUED)
Electrical Specifications: Unless otherwise indicated, VIN = VR + 1.5V, (Note 1), IL = 100 µA, CL = 3.3 µF,
SHDN > VIH, TA = +25°C. Boldface type specifications apply for junction temperatures of -40°C to +125°C.
Parameters
Sym
Min
Typ
Max
Units
SHDN Input High Threshold
VIH
45
—
—
%VIN
SHDN Input Low Threshold
VIL
—
—
15
%VIN
Minimum Operating Voltage
VMIN
1.0
—
—
V
Output Logic Low Voltage
VOL
—
—
400
mV
ERROR Threshold Voltage
VTH
—
0.95 x VR
—
V
ERROR Positive Hysteresis
VHYS
—
50
—
mV
Conditions
SHDN Input
ERROR Output (SOIC Only)
1 mA Flows to ERROR
Note 8
Note 1: VR is the regulator output voltage setting.
2: The minimum VIN has to justify the conditions: VIN ≥ VR + VDROPOUT and VIN ≥ 2.7V for IL = 0.1 mA to IOUTMAX.
6
3:
(V
–V
) – 10
OUTMAX
OUTMIN
TCV OUT = ------------------------------------------------------------------------V OUT × ∆T
4: Regulation is measured at a constant junction temperature using low duty cycle pulse testing. Load regulation is tested
over a load range from 0.1 mA to the maximum specified output current. Changes in output voltage due to heating effects
are covered by the thermal regulation specification.
5: Dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal value
measured at a 1.5V differential.
6: Thermal regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied,
excluding load or line regulation effects. Specifications are for a current pulse equal to ILMAX at VIN = 6V for T = 10 ms.
7: The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction temperature and the thermal resistance from junction-to-air (i.e., TA, TJ, θJA). Exceeding the maximum allowable power dissipation causes the device to initiate thermal shutdown. Please see Section 5.0 “Thermal Considerations” for more details.
8: Hysteresis voltage is referenced to VR.
TEMPERATURE CHARACTERISTICS
Electrical Specifications: Unless otherwise indicated, VIN = VR + 1.5V, IL = 100 µA, CL = 3.3 µF,
SHDN > VIH, TA = +25°C.
Parameters
Sym
Min
Typ
Max
Units
Specified Temperature Range
TA
-40
—
+125
°C
Operating Temperature Range
TJ
-40
—
+125
°C
Storage Temperature Range
TA
-65
—
+150
°C
Thermal Resistance, 5L-DDPAK
θJA
—
57
—
°C/W
Thermal Resistance, 5L-TO-220
θJA
—
71
—
°C/W
Thermal Resistance, 8L-SOIC
θJA
—
163
—
°C/W
Conditions
Temperature Ranges
(Note 1)
Thermal Package Resistances
Note 1:
Operation in this range must not cause TJ to exceed Maximum Junction Temperature (+125°C).
 2004 Microchip Technology Inc.
DS21376C-page 3
TC1265
TYPICAL PERFORMANCE CURVES
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
LINE REGULATION (%)
Note:
0.020
150
0.018
135
0.016
120
0.014
105
0.012
90
IDD (µA)
2.0
0.010
0.008
60
0.006
45
0.004
30
0.002
15
0.000
-40°C
0°C
25°C
70°C
85°C
VOUT = 3V
75
0
-40°C
125°C
Line Regulation vs.
NOISE (µV/√Hz)
10.0
RLOAD = 50Ω
COUT = 1µF
1.0
0.1
FIGURE 2-4:
DROPOUT VOLTAGE (V)
FIGURE 2-1:
Temperature.
0°C
25°C
70°C
125°C
85°C
TEMPERATURE (°C)
TEMPERATURE (°C)
IDD vs. Temperature.
0.600
0.550
0.500
0.450
0.400
0.350
125°C
85°C
70°C
25°C
0.300
0°C
0.250
0.200
-40°C
0.150
0.100
0.050
0.0
0.01
0.01
1
10
100
0.000
1000
0 100 200 300 400 500 600 700 800
ILOAD (mA)
FREQUENCY (kHz)
FIGURE 2-2:
Output Noise vs. Frequency.
FIGURE 2-5:
ILOAD.
3.030
3.020
0.0090
0.0080
0.0070
0.0060
0.0050
VOUT = 3V
1 mA to 800 mA
0.0040
0.0030
2.990
2.980
2.970
2.950
2.940
0.0010
2.930
0.0100
-40°C
0°C
25°C
70°C
85°C
125°C
2.920
-40°C
DS21376C-page 4
ILOAD =
300mA
ILOAD =
500mA
ILOAD =
800mA
0°C
25°C
70°C
85°C 125°C
TEMPERATURE (°C)
TEMPERATURE (°C)
Load Regulation vs.
0.1mA
2.960
0.0020
FIGURE 2-3:
Temperature.
ILOAD =
3.010
3.000
VOUT (V)
LOAD REGULATION (%/mA)
0.0100
3.0V Dropout Voltage vs.
FIGURE 2-6:
3.0V VOUT vs.Temperature.
 2004 Microchip Technology Inc.
TC1265
2.0
TYPICAL PERFORMANCE CURVES (CONT)
0.090
0.080
ISHDN (µA)
0.070
0.060
0.050
0.040
0.030
0.020
0.010
0.000
-40°C
0°C
25°C
70°C
85°C
125°C
TEMPERATURE (°C)
FIGURE 2-1:
ISHDN vs. Temperature.
 2004 Microchip Technology Inc.
DS21376C-page 5
TC1265
3.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
Pin No.
(8-Pin SOIC)
3.1
PIN FUNCTION TABLE
Pin No.
(5-Pin DDPAK)
(5-Pin TO-220)
Symbol
Description
1
5
VOUT
Regulated voltage output
2
3
GND
Ground terminal
3
—
NC
4
1
BYPASS
Reference bypass input
5
—
ERROR
Out-of-Regulation Flag (open drain output)
6
2
SHDN
7
—
NC
No connect
8
4
VIN
Unregulated supply input
No connect
Shutdown control input
Regulated Output Voltage (VOUT)
Regulated voltage output.
3.2
Ground (GND)
3.4
Out-of-Regulation Flag (ERROR)
Out-of-regulation flag (open-drain output). This output
goes low when VOUT is out-of-tolerance by
approximately -5%.
Ground terminal.
3.5
3.3
Shutdown control input. The regulator is fully enabled
when a logic-high is applied to this input. The regulator
enters shutdown when a logic-low is applied to this
input. During shutdown, the output voltage falls to zero
and the supply current is reduced to 0.05 µA (typical).
Reference Bypass (BYPASS)
Reference bypass input. Connecting a 470 pF to this
input further reduces output noise.
3.6
Shutdown Control (SHDN)
Unregulated Supply (VIN)
Unregulated supply input.
DS21376C-page 6
 2004 Microchip Technology Inc.
TC1265
4.0
DETAILED DESCRIPTION
4.2
The TC1265 is a precision, fixed-output LDO. Unlike
bipolar regulators, the TC1265’s supply current does
not increase with load current. In addition, VOUT
remains stable and within regulation over the entire
0 mA to ILOADMAX load current range (an important
consideration in RTC and CMOS RAM battery back-up
applications).
Figure 4-1 shows a typical application circuit.
ERROR Output
ERROR is driven low whenever VOUT falls out of
regulation by more than – 5% (typ.). This condition may
be caused by low input voltage, output current limiting,
or thermal limiting. The ERROR threshold is 5% below
rated VOUT regardless of the programmed output
voltage value (e.g., ERROR = VOL at 4.75V (typ.) for a
5.0V regulator and 2.85V (typ.) for a 3.0V regulator).
ERROR output operation is shown in Figure 4-2.
Note that ERROR is active when VOUT is at or below
VTH and inactive when VOUT is above VTH + VH.
+
+
1 µF
C1
Battery
VIN
VOUT
TC1265
+
1 µF
C2
VOUT
GND
V+
SHDN
Shutdown Control
(to CMOS Logic or Tie
to VIN, if unused)
ERROR
R1
1M
C3 Required Only
if ERROR is used as a
Processor RESET Signal
(See Text)
+
0.2 µF
C3
BATTLOW
or RESET
As shown in Figure 4-1, ERROR can be used as a
battery low flag or as a processor RESET signal (with
the addition of timing capacitor C3). R1 x C3 should be
chosen to maintain ERROR below VIH of the processor
RESET input for at least 200 ms to allow time for the
system to stabilize. Pull-up resistor R1 can be tied to
VOUT, VIN or any other voltage less than (VIN + 0.3V).
VOUT
VTH
FIGURE 4-1:
4.1
Typical Application Circuit.
Output Capacitor
A 1 µF (min.) capacitor from VOUT to ground is
required. The output capacitor should have an Effective
Series Resistance (ESR) greater than 0.1Ω and less
than 5Ω. A 1 µF capacitor should be connected from
VIN to GND if there is more than 10 inches of wire
between the regulator and the AC filter capacitor, or if a
battery is used as the power source. Aluminum electrolytic or tantalum capacitor types can be used. Since
many aluminum electrolytic capacitors freeze at
approximately -30°C, solid tantalums are recommended for applications operating below -25°C. When
operating from sources other than batteries, supplynoise rejection and transient response can be
improved by increasing the value of the input and
output capacitors, and by employing passive filtering
techniques.
 2004 Microchip Technology Inc.
Hysteresis (VH)
ERROR
VIH
VOL
FIGURE 4-2:
ERROR Output Operation.
DS21376C-page 7
TC1265
5.0
THERMAL CONSIDERATIONS
5.1
Thermal Shutdown
Integrated thermal protection circuitry shuts the
regulator off when die temperature exceeds 160°C.
The regulator remains off until the die temperature
drops to approximately 150°C.
5.2
Power Dissipation
The amount of power the regulator dissipates is
primarily a function of input voltage, output voltage and
output current. The following equation is used to
calculate worst-case actual power dissipation:
EQUATION 5-1:
P D = ( V INMAX – VOUTMIN )I LOADMAX
Where:
Copper
Area
(Topside)*
THERMAL RESISTANCE
GUIDELINES FOR TC1265 IN
5-PIN DDPAK/TO-220
PACKAGE
Copper
Area
(Backside)
Board
Area
Thermal
Resistance
(θJA)
2500 sq mm 2500 sq mm 2500 sq mm
25°C/W
1000 sq mm 2500 sq mm 2500 sq mm
27°C/W
125 sq mm
35°C/W
2500 sq mm 2500 sq mm
* Tab of device attached to top-side copper
Equation 5-1 can be used in conjunction with
Equation 5-2 to ensure regulator thermal operation is
within limits. For example:
Given:
VINMAX = 3.3V ± 10%
VOUTMIN = 2.7V ± 0.5%
PD = Worst-case actual power dissipation
VINMAX = Maximum voltage on VIN
VOUTMIN = Minimum regulator output voltage
ILOADMAX = Maximum output (load) current
The
maximum
allowable
power
dissipation
(Equation 5-2) is a function of the maximum ambient
temperature (TAMAX), the maximum allowable die
temperature (TJMAX) and the thermal resistance from
junction-to-air (θJA).
PDMAX
TJMAX = 125°C
TAMAX = 95°C
θJA = 60°C/W (SOIC)
Find:
1. Actual power dissipation
2. Maximum allowable dissipation
Actual power dissipation:
P D = ( 3.3 × 1.1 ) – ( 2.7 × .995 ) 275 × 10
T JMAX – T AMAX
= --------------------------------------θ JA
–3
P D = 260 mW
PD = Worst-case actual power dissipation
VINMAX = Maximum voltage on VIN
VOUTMIN = Minimum regulator output voltage
ILOADMAX = Maximum output (load) current
Table 5-1 and Table 5-2 show various values of θJA for
the TC1265 package types.
TABLE 5-1:
ILOADMAX = 275 mA
P D ≈ ( VINMAX – V OUTMIN )I LOADMAX
EQUATION 5-2:
Where:
TABLE 5-2:
THERMAL RESISTANCE
GUIDELINES FOR TC1265 IN
8-PIN SOIC PACKAGE
Copper
Area
(Topside)*
Copper
Area
(Backside)
Board
Area
Thermal
Resistance
(θJA)
2500 sq mm
2500 sq mm
2500 sq mm
60°C/W
1000 sq mm
2500 sq mm
2500 sq mm
60°C/W
225 sq mm
2500 sq mm
2500 sq mm
68°C/W
100 sq mm
2500 sq mm
2500 sq mm
74°C/W
Maximum allowable power dissipation:
T JMAX – T AMAX
P DMAX = --------------------------------------θ JA
( 125 – 95 )
P DMAX = ------------------------60
P DMAX = 500 mW
In this example, the TC1265 dissipates a maximum of
260 mW, below the allowable limit of 500 mW. In a
similar manner, Equation 5-1 and Equation 5-2 can be
used to calculate maximum current and/or input
voltage limits. For example, the maximum allowable
VIN is found by substituting the maximum allowable
power dissipation of 500 mW into Equation 5-1, from
which VINMAX = 4.6V.
* Pin 2 is ground. Device is mounted on the top-side.
DS21376C-page 8
 2004 Microchip Technology Inc.
TC1265
6.0
PACKAGING INFORMATION
6.1
Package Marking Information
5-Lead DDPAK
Example
XXXXXXXXX
XXXXXXXXX
YYWWNNN
TC1265
3.3VET
0430256
5-Lead TO-220
XXXXXXXXX
XXXXXXXXX
YYWWNNN
TC12653.3VATX
0430256
8-Lead SOIC (150 mil)
XXXXXXXX
XXXXYYWW
NNN
Legend:
Note:
*
XX...X
YY
WW
NNN
Example:
Example:
1265-3.3
VOA0430
256
Customer specific information*
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line thus limiting the number of available characters
for customer specific information.
Standard OTP marking consists of Microchip part number, year code, week code, and traceability code.
 2004 Microchip Technology Inc.
DS21376C-page 9
TC1265
5-Lead Plastic (ET) (DDPAK)
E
E1
L3
D2
D
D1
1
BOTTOM VIEW
e
b
TOP VIEW
θ1
(5X)
c2
A
θ
A1
c
L
Units
Dimension Limits
Number of Pins
Pitch
Overall Height
Standoff §
Overall Width
Exposed Pad Width
Molded Package Length
Overall Length
Exposed Pad Length
Lead Thickness
Pad Thickness
Lead Width
Foot Length
Pad Length
Foot Angle
Mold Draft Angle
MIN
e
A
A1
E
E1
D
D1
D2
c
c2
b
L
L3
θ
θ1
.170
.000
.385
.330
.549
.014
.045
.026
.068
.045
-3°
INCHES*
NOM
5
.067 BSC
.177
.005
.398
.256 REF
.350
.577
.303 REF
.020
-.032
.089
----
MAX
.183
.010
.410
.370
.605
.026
.055
.037
.110
.067
8°
7°
MILLIMETERS
NOM
5
1.70 BSC
4.50
4.32
0.13
0.00
10.11
9.78
6.50 REF
8.38
8.89
13.94
14.66
7.75 REF
0.36
0.51
1.14
-0.66
0.81
1.73
2.26
1.14
---3°
--
MIN
MAX
4.65
0.25
10.41
9.40
15.37
0.66
1.40
0.94
2.79
1.70
8°
7°
*Controlling Parameter
§ Significant Characteristic
Notes:
Dimensions D and E do not include mold flash or protrusions. Mold flash or protrusions shall not
exceed .010" (0.254mm) per side.
JEDEC equivalent: TO-252
Drawing No. C04-012
DS21376C-page 10
 2004 Microchip Technology Inc.
TC1265
5-Lead Plastic Transistor Outline (AT) (TO-220)
L
H1
Q
b
e3
e1
E
e
ØP
EJECTOR PIN
a (5X)
C1
A
J1
F
D
Units
Dimension Limits
e
Lead Pitch
Overall Lead Centers
Space Between Leads
Overall Height
Overall Width
Overall Length
Flag Length
Flag Thickness
Through Hole Center
Through Hole Diameter
Lead Length
Base to Bottom of Lead
Lead Thickness
Lead Width
Mold Draft Angle
e1
e3
A
E
D
H1
F
Q
P
L
J1
C1
b
a
INCHES*
MAX
MIN
.060
.072
.263
.273
.030
.040
.190
.160
.385
.415
.560
.590
.234
.258
.045
.055
.103
.113
.146
.156
.560
.540
.090
.115
.022
.014
.025
.040
3°
7°
MILLIMETERS
MIN
MAX
1.52
1.83
6.68
6.93
0.76
1.02
4.06
4.83
9.78
10.54
14.22
14.99
5.94
6.55
1.14
1.40
2.62
2.87
3.71
3.96
13.72
14.22
2.29
2.92
0.36
0.56
0.64
1.02
3°
7°
*Controlling Parameter
Notes:
Dimensions D and E1 do not include mold flash or protrusions. Mold flash or
protrusions shall not exceed .010" (0.254mm) per side.
JEDEC equivalent: TO-220
Drawing No. C04-036
 2004 Microchip Technology Inc.
DS21376C-page 11
TC1265
8-Lead Plastic Small Outline (SN) – Narrow, 150 mil Body (SOIC)
E
E1
p
D
2
B
n
1
α
h
45°
c
A2
A
φ
β
L
Units
Dimension Limits
n
p
Number of Pins
Pitch
Overall Height
Molded Package Thickness
Standoff §
Overall Width
Molded Package Width
Overall Length
Chamfer Distance
Foot Length
Foot Angle
Lead Thickness
Lead Width
Mold Draft Angle Top
Mold Draft Angle Bottom
* Controlling Parameter
§ Significant Characteristic
A
A2
A1
E
E1
D
h
L
φ
c
B
α
β
MIN
.053
.052
.004
.228
.146
.189
.010
.019
0
.008
.013
0
0
A1
INCHES*
NOM
8
.050
.061
.056
.007
.237
.154
.193
.015
.025
4
.009
.017
12
12
MAX
.069
.061
.010
.244
.157
.197
.020
.030
8
.010
.020
15
15
MILLIMETERS
NOM
8
1.27
1.35
1.55
1.32
1.42
0.10
0.18
5.79
6.02
3.71
3.91
4.80
4.90
0.25
0.38
0.48
0.62
0
4
0.20
0.23
0.33
0.42
0
12
0
12
MIN
MAX
1.75
1.55
0.25
6.20
3.99
5.00
0.51
0.76
8
0.25
0.51
15
15
Notes:
Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed
.010” (0.254mm) per side.
JEDEC Equivalent: MS-012
Drawing No. C04-057
DS21376C-page 12
 2004 Microchip Technology Inc.
TC1265
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
X.XX
XX
XX
Device
Voltage
Option
Package
Tape and
Reel
Device
TC1265 Fixed Output CMOS LDO with Shutdown
Voltage Option:*
1.8V
2.5V
3.0V
3.3V
=
=
=
=
1.8V
2.5V
3.0V
3.3V
Examples:
a)
b)
c)
d)
TC1265-1.8VAT
TC1265-2.5VAT
TC1265-3.0VAT
TC1265-3.3VAT
a)
TC1265-1.8VETTR 1.8V LDO, DDPAK-5 pkg.,
Tape and Reel
TC1265-2.5VETTR 2.5V LDO, DDPAK-5 pkg.,
Tape and Reel
TC1265-3.0VETTR 3.0V LDO, DDPAK-5 pkg.,
Tape and Reel
TC1265-3.3VETTR 3.3V LDO, DDPAK-5 pkg.,
Tape and Reel
b)
c)
d)
* Other output voltages are available. Please contact your
local Microchip sales office for details.
a)
b)
Package
AT
ET
ETTR
=
=
=
OA
=
OATR =
Plastic (TO-220), 5-Lead
Plastic Transistor Outline (DDPAK), 5-Lead
Plastic Transistor Outline (DDPAK), 5-Lead,
Tape and Reel
Plastic SOIC, (150 mil Body), 8-lead
Plastic SOIC, (150 mil Body), 8-lead,
Tape and Reel
c)
d)
e)
f)
g)
h)
1.8V LDO, TO-220-5 pkg.
2.5V LDO, TO-220-5 pkg.
3.0V LDO, TO-220-5 pkg.
3.3V LDO, TO-220-5 pkg.
TC1265-1.8VOA
1.8V LDO, SOIC-8 pkg.
TC1265-1.8VOATR 1.8V LDO, SOIC-8 pkg.,
Tape and Reel
TC1265-2.5VOA
2.5V LDO, SOIC-8 pkg.
TC1265-2.5VOATR 2.5V LDO, SOIC-8 pkg.,
Tape and Reel
TC1265-3.0VOA
3.0V LDO, SOIC-8 pkg.
TC1265-3.0VOATR 3.0V LDO, SOIC-8 pkg.,
Tape and Reel
TC1265-3.3VOA
3.3V LDO, SOIC-8 pkg.
TC1265-3.3VOATR 3.3V LDO, SOIC-8 pkg.,
Tape and Reel
Sales and Support
Data Sheets
Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and
recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following:
1.
2.
Your local Microchip sales office
The Microchip Worldwide Site (www.microchip.com)
Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using.
Customer Notification System
Register on our web site (www.microchip.com) to receive the most current information on our products.
 2004 Microchip Technology Inc.
DS21376C-page 13
TC1265
NOTES:
DS21376C-page 14
 2004 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED,
WRITTEN OR ORAL, STATUTORY OR OTHERWISE,
RELATED TO THE INFORMATION, INCLUDING BUT NOT
LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE,
MERCHANTABILITY OR FITNESS FOR PURPOSE.
Microchip disclaims all liability arising from this information and
its use. Use of Microchip’s products as critical components in
life support systems is not authorized except with express
written approval by Microchip. No licenses are conveyed,
implicitly or otherwise, under any Microchip intellectual property
rights.
Trademarks
The Microchip name and logo, the Microchip logo, Accuron,
dsPIC, KEELOQ, microID, MPLAB, PIC, PICmicro,
PICSTART, PRO MATE, PowerSmart, rfPIC, and
SmartShunt are registered trademarks of Microchip
Technology Incorporated in the U.S.A. and other countries.
AmpLab, FilterLab, MXDEV, MXLAB, PICMASTER, SEEVAL,
SmartSensor and The Embedded Control Solutions Company
are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, dsPICDEM,
dsPICDEM.net, dsPICworks, ECAN, ECONOMONITOR,
FanSense, FlexROM, fuzzyLAB, In-Circuit Serial
Programming, ICSP, ICEPIC, Migratable Memory, MPASM,
MPLIB, MPLINK, MPSIM, PICkit, PICDEM, PICDEM.net,
PICLAB, PICtail, PowerCal, PowerInfo, PowerMate,
PowerTool, rfLAB, rfPICDEM, Select Mode, Smart Serial,
SmartTel and Total Endurance are trademarks of Microchip
Technology Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2004, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 quality system certification for
its worldwide headquarters, design and wafer fabrication facilities in
Chandler and Tempe, Arizona and Mountain View, California in
October 2003. The Company’s quality system processes and
procedures are for its PICmicro® 8-bit MCUs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
 2004 Microchip Technology Inc.
DS21376C-page 15
WORLDWIDE SALES AND SERVICE
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://support.microchip.com
Web Address:
www.microchip.com
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
India - Bangalore
Tel: 91-80-2229-0061
Fax: 91-80-2229-0062
China - Beijing
Tel: 86-10-8528-2100
Fax: 86-10-8528-2104
India - New Delhi
Tel: 91-11-5160-8631
Fax: 91-11-5160-8632
Austria - Weis
Tel: 43-7242-2244-399
Fax: 43-7242-2244-393
Denmark - Ballerup
Tel: 45-4450-2828
Fax: 45-4485-2829
China - Chengdu
Tel: 86-28-8676-6200
Fax: 86-28-8676-6599
Japan - Kanagawa
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
France - Massy
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
China - Fuzhou
Tel: 86-591-8750-3506
Fax: 86-591-8750-3521
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
Germany - Ismaning
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Atlanta
Alpharetta, GA
Tel: 770-640-0034
Fax: 770-640-0307
Boston
Westford, MA
Tel: 978-692-3848
Fax: 978-692-3821
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
China - Shunde
Tel: 86-757-2839-5507
Fax: 86-757-2839-5571
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
England - Berkshire
Tel: 44-118-921-5869
Fax: 44-118-921-5820
Taiwan - Hsinchu
Tel: 886-3-572-9526
Fax: 886-3-572-6459
China - Qingdao
Tel: 86-532-502-7355
Fax: 86-532-502-7205
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
San Jose
Mountain View, CA
Tel: 650-215-1444
Fax: 650-961-0286
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
10/20/04
DS21376C-page 16
 2004 Microchip Technology Inc.