tfs400k.doc version 3.2 VI TELEFILTER 01.12.2003 Preliminary Specification TFS 400 K 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: External coil: 23 10 375 375 47 nH °C dBm -1.9 pF -1.9 pF Characteristics Remark: Reference level for the relative attenuation arel of the TFS400K is the minimum of the pass band attenuation amin . The minimum of the pass band attenuation amin is defined as the insertion loss ae. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the 1 dB filter attenuation level relative to the insertion loss ae . The nominal frequency fN is fixed at 400 MHz without tolerance. The given values for the relative attenuation arel and for the group delay ripple have to be reached at the frequencies given below even if the centre frequency fc is shifted due to the temperature coefficient of frequency TCf in the operating temperature range and due to a production tolerance for the centre frequency fc. Data typ. value Insertion Loss (reference level) ae 4,5 Nominal Frequency fN 400,04 Bandwidth BW 3 dB 500 700 1 MHz 6,5 400 dB MHz - arel Relative Attenuation ± ± ± max. T.B.D. fN fN fN fN dB tolerance / limit ... fN ± kHz ... fN kHz ... fN MHz ... fN ± ± ± 82,5 700 1 13 kHz 0,4 kHz MHz MHz 28 43 50 dB max. 1 dB dB dB dB min. min. min. 15 27 40 dB dB dB µs max. 1 µs Group Delay Ripple fN ± 82,5 kHz Operating Temperature Range 0,6 OTR -40 °C ... + 85 °C - Storage Temperature Range Frequency Inversion Temperature Temperature Coefficient of Frequency - TCf ** - 40 °C ... + 85°C 20 °C - -0,036 ppm/K² - *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. These values have to be confirmed by balanced s-parameter measurement. **) f(Hz) = TCf(ppm/K) x (T-T0)² x fTo(MHz). Generated: Checked / Approved: TELEFILTER GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-52 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. tfs400k.doc version 3.2 VI TELEFILTER 01.12.2003 Preliminary Specification Construction, pin configuration and 50 TFS 400 K 2/5 - matching network (all dimensions in mm) +0.15 5.0 SQ -0.1 7 5 400 K R20 1 3 Date code Pin Pin Pin Pin 1 2 3 4,8 Sym. Output Sym. Output External Coil Package Ground Pin 5 Pin 6 Pin 7 Sym. Input Sym. Input Ground Date code: N P R ... Year + week 2001 2002 2003 50 Ohm Test circuit 1 LB-IN L1 6 SAW C1 2 LB-IN C1 L5 6 C3 1 SAW L1 C2 L4 3 4, 7, 8 50 Ohm Test circuit 2 LB-OUT L2 2 5 3 4, 7, 8 LB-OUT C2 5 L2 L3 1 C4 L3 TELEFILTER GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-52 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. tfs400k.doc version 3.2 VI TELEFILTER 01.12.2003 Preliminary Specification TFS 400 K 3/5 Stability Characteristics After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 18 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 3. Change of temperature: -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 14 Test N 4. Resistance to older heat (reflow): reflow possible: twice max.; for temperature conditions, please refer to the attached "Air reflow temperature conditions" on page 4 Packing Tape & Reel: IEC 286 - 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer Tape (all dimensions in mm) W : 12 ± 0,3 Po : 4 ± 0,1 Do : 1,5 + 0,1 E : 1,75 ± 0,1 F : 5,5 ± 0,05 G (min) : 0,75 P2 : 2 ± 0,05 P1 : 8 ± 0,1 D1(min) : 1,5 Ao : 5,3 ± 0,1 Bo : 5,3 ± 0,1 CT : 9,5 ± 0,1 3000 min 300 mm min 500 mm min 300 mm EMBOSSED CARRIER TAPE Do Po P2 E Ao F D1 CT W Bo G P1 COVER TAPE W2 Reel (all d imensions in mm): A : W1 : W2 (m ax) : 330 12 ,4 + 2 18 ,4 N (m in) : 50 C : 13 + 0 ,5 - 0 ,2 A C N W 1 The minimum bending radius is 45 mm. The mounting surface of the filters faces the bottom side of the embossed carrier tape. The marking of the filters is able to read if the view is directed on the upper side of the carrier tape with the sprocket holes on the right side of the tape. TELEFILTER GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-52 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. tfs400k.doc version 3.2 VI TELEFILTER 01.12.2003 Preliminary Specification TFS 400 K 4/5 Air reflow temperature conditions 1st and 2nd air reflow profile pre-heating periods 150 °C - 170 °C 60 sec. - 90 sec. Name: Temperature: Time: main-heating periods over 200 °C 20 sec. - 25 sec. peak temperature 255 °C ± 5 °C Chip-mount air reflow profile 260 240 220 200 temperature / °C 180 160 140 120 100 80 60 40 20 0 0 20 40 60 80 100 120 140 160 180 200 220 240 time / sec. Table for temperature vs. time during the air reflow process Tolerance of temperatures: ± 5 °C time / sec. 0 10 20 30 40 50 60 70 80 90 100 110 120 130 temperature / °C 23 34 46 60 80 103 121 134 143 150 154 156 158 159 time / sec. 140 150 160 170 180 190 195 200 205 210 215 220 230 240 temperature / °C 160 161 164 170 180 205 230 255 230 205 180 165 140 120 TELEFILTER GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-52 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. tfs400k.doc version 3.2 VI TELEFILTER 01.12.2003 Preliminary Specification TFS 400 K 5/5 History Version Reason of Changes Name Date 1.0 - Generate development specification. Pfeiffer 12.05.2003 2.0 - Modification of electrical data based on TFS400B to support a group delay ripple of 1 µs maximum. - Correct reel dimensions. Dr. Wall 11.06.2003 3.0 - Dr. Wall 19.06.2003 3.1 - Change frequency band for 1 dB pass band and group delay ripple requirement Dr. Wall 03.07.2003 3.2 - Change from development specification to preliminary specification - Add preliminary values for termination impedances - Add typical values Dr. Wall 01.12.2003 Add 1 dB pass band of 160 kHz. Shift 15 dB limit line to +-500 kHz Shift 27 dB limit line to +-700 kHz Remove values for termination impedances and coupling coil. Add 50 Ohm test circuit configuration. TELEFILTER GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-52 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.