µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005
D
D
D
D
D
D
D
D
D
D
Rail-To-Rail Input/Output
Wide Bandwidth . . . 3 MHz
High Slew Rate . . . 2.4 V/µs
Supply Voltage Range . . . 2.7 V to 16 V
Supply Current . . . 550 µA/Channel
Low Power Shutdown Mode
IDD(SHDN) . . . 25 µA/Channel
Input Noise Voltage . . . 39 nV/√Hz
Input Bias Current . . . 1 pA
Specified Temperature Range
−40°C to 125°C . . . Industrial Grade
Ultrasmall Packaging
5 or 6 Pin SOT-23 (TLV2370/1)
8 or 10 Pin MSOP (TLV2372/3)
Operational Amplifier
−
+
description
The TLV237x single supply operational amplifiers provide rail-to-rail input and output capability. The TLV237x
takes the minimum operating supply voltage down to 2.7 V over the extended industrial temperature range while
adding the rail-to-rail output swing feature. The TLV237x also provides 3-MHz bandwidth from only 550 µA. The
maximum recommended supply voltage is 16 V, which allows the devices to be operated from (±8 V supplies
down to ±1.35 V) a variety of rechargeable cells.
The CMOS inputs enable use in high-impedance sensor interfaces, with the lower voltage operation making
an ideal alternative for the TLC227x in battery-powered applications. The rail-to-rail input stage further
increases its versatility. The TLV237x is the seventh member of a rapidly growing number of RRIO products
available from TI, and it is the first to allow operation up to 16-V rails with good ac performance.
All members are available in PDIP and SOIC with the singles in the small SOT-23 package, duals in the MSOP,
and quads in the TSSOP package.
The 2.7-V operation makes the TLV237x compatible with Li-Ion powered systems and the operating supply
voltage range of many micro-power microcontrollers available today including TI’s MSP430.
SELECTION OF SIGNAL AMPLIFIER PRODUCTS†
VDD (V)
VIO
(µV)
TLV237x
2.7−16
TLC227x
4−16
DEVICE
GBW
(MHz)
SR
(V/µs)
SHUTDOWN
RAILTORAIL
SINGLES/DUALS/QUADS
1
3
2.4
Yes
I/O
S/D/Q
1
2.2
3.6
—
O
D/Q
Iq/Ch
(µA)
IIB (pA)
500
550
300
1100
TLV27x
2.7−16
500
550
1
3
2.4
—
O
S/D/Q
TLC27x
3−16
1100
675
1
1.7
3.6
—
—
S/D/Q
TLV246x
2.7−6
150
550
1300
6.4
1.6
Yes
I/O
S/D/Q
TLV247x
2.7−6
250
600
2
2.8
1.5
Yes
I/O
S/D/Q
TLV244x
2.7−10
300
† Typical values measured at 5 V, 25°C
725
1
1.8
1.4
—
O
D/Q
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2001−2005, Texas Instruments Incorporated
!"#$%&'(!$" !) *+%%,"( ') $# -+./!*'(!$" 0'(,1
%$0+*() *$"#$%& ($ )-,*!#!*'(!$") -,% (, (,%&) $# ,2') ")(%+&,"()
)('"0'%0 3'%%'"(41 %$0+*(!$" -%$*,))!"5 0$,) "$( ",*,))'%!/4 !"*/+0,
(,)(!"5 $# '// -'%'&,(,%)1
WWW.TI.COM
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
1
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005
FAMILY PACKAGE TABLE(1)
PACKAGE TYPES
NUMBER OF
CHANNELS
PDIP
SOIC
SOT-23
TSSOP
MSOP
TLV2370
1
8
8
6
—
—
Yes
TLV2371
1
8
8
5
—
—
—
TLV2372
2
8
8
—
—
8
—
TLV2373
2
14
14
—
—
10
Yes
TLV2374
4
14
14
—
14
—
—
TLV2375
4
16
16
—
16
—
Yes
DEVICE
SHUTDOWN
UNIVERSAL
EVM BOARD
Refer to the EVM
Selection Guide
(Lit# SLOU060)
TLV2370 and TLV2371 AVAILABLE OPTIONS(1)
PACKAGED DEVICES
VIOMAX AT
25°C
TA
−40°C to 125°C
4.5 mV
SOT-23
SMALL OUTLINE
(D)†
(DBV)‡
TLV2370ID
TLV2371ID
PLASTIC DIP
(P)
SYMBOL
TLV2370IDBV
TLV2371IDBV
VBFI
VBGI
TLV2370IP
TLV2371IP
† This package is available taped and reeled. To order this packaging option, add an R suffix to the part number (e.g., TLV2370IDR).
‡ This package is only available taped and reeled. For standard quantities (3,000 pieces per reel), add an R suffix (e.g., TLV2370IDBVR). For
smaller quantities (250 pieces per mini-reel), add a T suffix to the part number (e.g., TLV2370IDBVT).
TLV2372 AND TLV2373 AVAILABLE OPTIONS(1)
PACKAGED DEVICES
TA
−40°C
to
125°C
VIOMAX AT
25°C
4.5 mV
SMALL
OUTLINE
(D)§
(DGK)§
SYMBOL
(DGS)§
TLV2372ID
TLV2373ID
TLV2372IDGK
—
APG
—
—
TLV2373IDGS
SYMBOL
PLASTIC
DIP
(N)
PLASTIC
DIP
(P)
—
API
—
TLV2373IN
TLV2372IP
—
MSOP
§ This package is available taped and reeled. To order this packaging option, add an R suffix to the part number (e.g., TLV2372IDR).
TLV2374 and TLV2375 AVAILABLE OPTIONS(1)
PACKAGED DEVICES
TA
VIOMAX AT
25°C
−40°C to 125°C
4.5 mV
SMALL OUTLINE
(D)¶
PLASTIC DIP
(N)
TSSOP
(PW)¶
TLV2374ID
TLV2375ID
TLV2374IN
TLV2375IN
TLV2374IPW
TLV2375IPW
¶ This package is available taped and reeled. To order this packaging option, add an R suffix to the part number
(e.g., TLV2374IDR).
1. For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website
at www.ti.com.
2
WWW.TI.COM
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005
TLV237x PACKAGE PINOUTS(1)
TLV2370
D OR P PACKAGE
(TOP VIEW)
TLV2370
DBV PACKAGE
(TOP VIEW)
OUT
1
6
VDD
GND
2
5
SHDN
IN+
3
4
IN −
TLV2371
D OR P PACKAGE
(TOP VIEW)
NC
IN −
IN +
GND
1OUT
1IN −
1IN+
GND
NC
1SHDN
NC
1
8
2
7
3
6
4
5
NC
IN −
IN +
GND
1
8
2
7
3
6
4
5
TLV2371
DBV PACKAGE
(TOP VIEW)
SHDN
VDD
OUT
NC
1OUT
1IN −
1IN +
GND
1
8
2
7
3
6
4
5
TLV2374
D, N, OR PW PACKAGE
(TOP VIEW)
(TOP VIEW)
14
13
3
12
4
5
6
7
11
10
9
8
GND
2
IN+
3
VDD
2OUT
2IN −
2IN+
NC
2SHDN
NC
1OUT
1IN −
1IN+
VDD
2IN+
2IN −
2OUT
1
14
2
13
3
12
4
11
5
10
6
9
7
8
5
VDD
4
IN −
TLV2373
DGS PACKAGE
(TOP VIEW)
VDD
2OUT
2IN −
2IN+
TLV2373
D OR N PACKAGE
2
1
TLV2372
D, DGK, OR P PACKAGE
(TOP VIEW)
NC
VDD
OUT
NC
1
OUT
1OUT
1IN −
1IN+
GND
1SHDN
1
2
3
4
5
10
9
8
7
6
VDD
2OUT
2IN −
2IN+
2SHDN
TLV2375
D, N, OR PW PACKAGE
(TOP VIEW)
4OUT
4IN −
4IN+
GND
3IN+
3IN −
3OUT
1OUT
1IN −
1IN+
VDD+
2IN+
2IN −
2OUT
1/2SHDN
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
4OUT
4IN −
4IN+
GND
3IN +
3IN−
3OUT
3/4SHDN
NC − No internal connection
TYPICAL PIN 1 INDICATORS
Pin 1
Printed or
Molded Dot
NOTE:
Pin 1
Stripe
Pin 1
Bevel Edges
Pin 1
Molded “U” Shape
(1) If there is not a Pin 1 indicator, turn device to enable reading the symbol from the left to right. Pin 1 is at the lower left corner of the
device.
WWW.TI.COM
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
3
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5 V
Differential input voltage, VID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± VDD
Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.2 V to VDD + 0.2 V
Input current range, II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 10 mA
Output current range, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 100 mA
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA: I-suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 125°C
Maximum junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE:
All voltage values, except differential voltages, are with respect to GND.
DISSIPATION RATING TABLE
PACKAGE
θJC
(°C/W)
θJA
(°C/W)
TA ≤ 25°C
POWER RATING
D (8)
38.3
176
710 mW
D (14)
26.9
122.3
1022 mW
D (16)
25.7
114.7
1090 mW
DBV (5)
55
324.1
385 mW
DBV (6)
55
294.3
425 mW
DGK (8)
54.23
259.96
481 mW
DGS (10)
54.1
257.71
485 mW
N (14, 16)
32
78
1600 mW
P (8)
41
104
1200 mW
PW (14)
29.3
173.6
720 mW
PW (16)
28.7
161.4
774 mW
recommended operating conditions
Single supply
Supply voltage, VDD
Split supply
Common-mode input voltage range, VICR
Operating free-air temperature, TA
I-suffix
MIN
MAX
2.7
16
±1.35
±8
0
VDD
125
°C
2
V
−40
Turnon voltage level, V(ON), relative to GND pin voltage
Turnoff voltage level, V(OFF), relative to GND pin voltage
4
0.8
WWW.TI.COM
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
UNIT
V
V
V
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005
electrical characteristics at specified free-air temperature, VDD = 2.7 V, 5 V, and 15 V (unless
otherwise noted)
dc performance
PARAMETER
TEST CONDITIONS
TA
MIN
25°C
VIO
Input offset voltage
αVIO
Offset voltage drift
VO = VDD/2,
VIC = VDD/2,
RS = 50 Ω
VIC = 0 to VDD−1.35V,
RS = 50 Ω
CMRR
Common-mode rejection ratio
VIC = 0 to VDD,
RS = 50 Ω,
VIC = 0 to VDD−1.35V,
RS = 50 Ω,
VIC = 0 to VDD,
RS = 50 Ω,
VIC = 0 to VDD−1.35V,
RS = 50 Ω,
VDD = 2.7 V
VDD = 5 V
VDD = 15 V
VDD = 2.7 V
AVD
Large-signal differential voltage
amplification
VO(PP) = VDD/2,
RL = 10 kkΩ
MAX
2
4.5
6
Full range
25°C
VIC = 0 to VDD,
RS = 50 Ω
TYP
50
Full range
49
25°C
56
Full range
54
25°C
55
Full range
54
25°C
67
Full range
64
25°C
64
Full range
63
25°C
67
Full range
66
25°C
98
Full range
76
25°C
100
VDD = 5 V
Full range
86
25°C
81
VDD = 15 V
Full range
79
mV
V/°C
µV/°C
2
25°C
UNIT
68
70
72
dB
80
82
84
106
110
dB
83
input characteristics
PARAMETER
IIO
TEST CONDITIONS
Input offset current
VDD = 15 V,
VO = VDD/2
IIB
VIC = VDD/2,
Differential input resistance
CIC
Common-mode input capacitance
f = 21 kHz
WWW.TI.COM
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
MIN
TYP
1
MAX
70°C
100
1000
1
UNIT
60
125°C
25°C
Input bias current
ri(d)
TA
25°C
pA
60
70°C
100
125°C
1000
pA
25°C
1000
GΩ
25°C
8
pF
5
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005
electrical characteristics at specified free-air temperature, VDD = 2.7 V, 5 V, and 15 V (unless
otherwise noted) (continued)
output characteristics
PARAMETER
TEST CONDITIONS
VIC = VDD/2, IOH = −1 mA
TA
MIN
TYP
25°C
2.55
2.58
VDD = 2.7 V
Full range
2.48
25°C
4.9
VDD = 5 V
Full range
4.85
25°C
14.92
Full range
14.9
25°C
1.9
Full range
1.6
25°C
4.6
VDD = 5 V
Full range
4.5
25°C
14.7
VDD = 15 V
Full range
14.6
VDD = 15 V
VOH
High-level output voltage
VDD = 2.7 V
VIC = VDD/2, IOH = −5 mA
25°C
VDD = 2.7 V
Full range
VDD = 15 V
Full range
Low-level output voltage
VDD = 5 V
0.05
IO
Output current
VDD = 5 V,
VO = 0.5 V from rail
VDD = 15 V, VO = 0.5 V from rail
0.15
0.1
0.08
0.1
0.52
Full range
0.7
V
1.1
0.28
Full range
0.4
0.5
25°C
VDD = 2.7 V, VO = 0.5 V from rail
14.8
0.15
25°C
VIC = VDD/2, IOL = 5 mA
4.68
0.22
25°C
VDD = 2.7 V
V
2
0.05
25°C
VOL
14.96
Full range
VDD = 5 V
UNIT
4.93
0.1
25°C
VIC = VDD/2, IOL = 1 mA
MAX
0.19
VDD = 15 V
Full range
Positive rail
25°C
4
Negative rail
25°C
5
Positive rail
25°C
7
Negative rail
25°C
8
Positive rail
25°C
16
Negative rail
25°C
15
0.3
0.35
mA
power supply
PARAMETER
IDD
Supply current (per channel)
TEST CONDITIONS
VDD = 2.7 V
VDD = 5 V
VO = VDD/2,
VDD = 15 V
PSRR
6
Supply voltage rejection ratio
(∆VDD /∆VIO)
VDD = 2.7 V to 15 V,
No load
VIC = VDD /2,
WWW.TI.COM
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
TA
25°C
MIN
TYP
MAX
470
560
25°C
550
660
25°C
750
900
Full range
UNIT
µA
1200
25°C
70
Full range
65
80
dB
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005
electrical characteristics at specified free-air temperature, VDD = 2.7 V, 5 V, and 15 V (unless
otherwise noted) (continued)
dynamic performance
PARAMETER
UGBW
TEST CONDITIONS
Unity gain bandwidth
RL = 2 kΩ,
CL = 10 pF
TA
2.4
VDD = 5 V to 15 V
25°C
3
25°C
φm
ts
Slew rate at unity gain
VO(PP) = VDD/2,
CL = 50 pF,
RL = 10 kΩ
TYP
25°C
VDD = 2.7 V
SR
MIN
VDD = 2.7 V
1.4
Full range
25°C
1.6
Full range
1.2
25°C
1.9
VDD = 15 V
Full range
1.4
2
V/ s
V/µs
2.4
V/ s
V/µs
2.1
V/ s
V/µs
Phase margin
RL = 2 kΩ,
CL = 100 pF
25°C
65°
Gain margin
RL = 2 kΩ,
CL = 10 pF
25°C
18
Settling time
VDD = 2.7 V,
V(STEP)PP = 1 V,
CL = 10 pF,
VDD = 5 V, 15 V,
V(STEP)PP = 1 V,
CL = 47 pF,
0.1%
AV = −1,
RL = 2 kΩ
0.1%
UNIT
MHz
1
VDD = 5 V
AV = −1,
RL = 2 kΩ
MAX
dB
2.9
µss
25°C
2
noise/distortion performance
PARAMETER
TEST CONDITIONS
VDD = 2.7 V,
VO(PP) = VDD/2 V,
RL = 2 kΩ,
k , f = 10 kHz
THD + N
Total harmonic distortion plus noise
VDD = 5 V, 15 V,
VO(PP) = VDD/2 V,
RL = 2 kΩ,
k , f = 10 kHz
AV = 1
AV = 10
TA
MIN
Equivalent input noise voltage
In
Equivalent input noise current
UNIT
0.05%
25°C
25
C
0.18%
0.02%
0.09%
25°C
25
C
0.5%
f = 1 kHz
Vn
MAX
0.02%
AV = 100
AV = 1
AV = 10
AV = 100
TYP
39
25°C
f = 10 kHz
f = 1 kHz
nV/√Hz
35
25°C
0.6
fA /√Hz
shutdown characteristics
PARAMETER
IDD(SHDN)
t(on)
t(off)
NOTE:
TEST CONDITIONS
Supply current in shutdown mode (TLV2370,
TLV2373, TLV2375) (per channel)
Amplifier turnon time (see Note 2)
Amplifier turnoff time (see Note 2)
VDD = 2.7 V, 5 V,
SHDN = 0 V
VDD = 15 V,
SHDN = 0 V
RL = 2 kΩ
TA
25°C
MIN
TYP
MAX
25
30
Full range
25°C
35
40
Full range
45
50
UNIT
µA
A
A
µA
25°C
0.8
µs
25°C
1
µs
Disable time and enable time are defined as the interval between application of the logic signal to the SHDN terminal and the point at
which the supply current has reached one half of its final value.
WWW.TI.COM
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
7
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
VIO
CMRR
Input offset voltage
vs Common-mode input voltage
Common-mode rejection ratio
vs Frequency
4
Input bias and offset current
vs Free-air temperature
5
VOL
VOH
Low-level output voltage
vs Low-level output current
6, 8, 10
High-level output voltage
vs High-level output current
7, 9, 11
VO(PP)
IDD
Peak-to-peak output voltage
vs Frequency
12
Supply current
vs Supply voltage
13
PSRR
Power supply rejection ratio
vs Frequency
14
AVD
Differential voltage gain & phase
vs Frequency
15
Gain-bandwidth product
vs Free-air temperature
16
vs Supply voltage
17
vs Free-air temperature
18
19
SR
Slew rate
φm
Vn
Phase margin
vs Capacitive load
Equivalent input noise voltage
vs Frequency
1, 2, 3
20
Voltage-follower large-signal pulse response
21, 22
Voltage-follower small-signal pulse response
23
Inverting large-signal response
24, 25
Inverting small-signal response
26
Crosstalk
vs Frequency
27
Shutdown forward & reverse isolation
vs Frequency
28
IDD(SHDN)
IDD(SHDN)
Shutdown supply current
vs Supply voltage
29
Shutdown pin leakage current
vs Shutdown pin voltage
IDD(SHDN)
Shutdown supply current/output voltage
vs Time
8
WWW.TI.COM
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
30
31, 32
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005
TYPICAL CHARACTERISTICS
INPUT OFFSET VOLTAGE
vs
COMMON-MODE INPUT VOLTAGE
INPUT OFFSET VOLTAGE
vs
COMMON-MODE INPUT VOLTAGE
1000
800
600
400
200
0
1000
VDD = 5 V
TA = 25 °C
800
600
400
200
0
−200
−200
0.4
0.8
1.2
1.6
2
0
VICR − Common-Mode Input Voltage − V
100
VDD = 5 V, 15 V
80
VDD = 2.7 V
40
20
100 k
10 k
250
200
150
100
50
0
−40 −25 −10 5
1M
TA = 70°C
TA = 25°C
0.80
TA = 0°C
0.40
0
4.50
4
3.50
1 2 3 4 5 6 7 8 9 10 11 12
IOH − High-Level Output Current − mA
Figure 7
1.60
1.20
TA = 70 °C
TA = 25 °C
0.80
0.40
TA = 125 °C
TA = 70 °C
2.50
TA = 25 °C
2
1.50
1
TA = 0 °C
TA = −40 °C
2 4 6 8 10 12 14 16 18 20 22 24
IOL − Low-Level Output Current − mA
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
5
VDD = 5 V
3
TA = 0 °C
TA = −40 °C
0.50
0
0
TA = 125 °C
Figure 6
V OH − High-Level Output Voltage − V
TA = 125°C
14 15
2
0
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
VOL − Low-Level Output Voltage − V
TA =−40°C
12
0
20 35 50 65 80 95 110 125
5
2.40
10
VDD = 2.7 V
2.40
Figure 5
VDD = 2.7 V
8
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
TA − Free-Air Temperature − °C
2.80
6
2.80
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
1.20
4
Figure 3
VDD = 2.7 V, 5 V and 15 V
VIC = VDD/2
Figure 4
1.60
2
VICR − Common-Mode Input Voltage −V
300
f − Frequency − Hz
2
0
0
−50
0
1k
200
INPUT BIAS/OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
I IB / I IO − Input Bias / Offset Current − pA
120
100
400
Figure 2
COMMON-MODE REJECTION RATIO
vs
FREQUENCY
10
600
1
2
3
4
5
VICR − Common-Mode Input Voltage − V
Figure 1
60
VDD =15 V
TA = 25 °C
800
−200
2.4 2.7
VOL − Low-Level Output Voltage − V
0
CMRR − Common-Mode Rejection Ratio − dB
V IO − Input Offset Voltage − µV
VDD = 2.7 V
TA = 25°C
V IO − Input Offset Voltage − µV
V IO − Input Offset Voltage − µV
1000
V OH − High-Level Output Voltage − V
INPUT OFFSET VOLTAGE
vs
COMMON-MODE INPUT VOLTAGE
VCC = 5 V
4.50
TA = −40°C
4
TA = 0°C
3.50
3
2.50
TA = 25°C
2
1.50
TA = 70°C
1
TA = 125°C
0.50
0
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70
IOL − Low-Level Output Current − mA
Figure 8
WWW.TI.COM
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
0
5
10
15
20
25
30
35
40
45
IOH − High-Level Output Current − mA
Figure 9
9
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005
TYPICAL CHARACTERISTICS
12
TA =70°C
10
TA =25°C
8
TA =0°C
6
TA =−40°C
4
2
15
14
VDD = 15 V
12
TA = −40°C
V O(PP) − Peak-to-Peak Output Voltage − V
VDD = 15 V
TA =125°C
V OH − High-Level Output Voltage − V
VOL − Low-Level Output Voltage − V
15
14
PEAK-TO-PEAK OUTPUT VOLTAGE
vs
FREQUENCY
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
10
TA = 0°C
8
6
TA = 25°C
4
TA = 70°C
TA = 125°C
2
0
0
0
0
20 40 60 80 100 120 140 160
IOL − Low-Level Output Current − mA
20
40
60
80
VDD = 2.7 V
100
AV = 1
VIC = VDD / 2
TA = 70°C
0.7
0.6
0.5
0.4
TA = 25°C
0.3
TA = 0°C
0.2
TA = −40°C
0.1
0
120
TA = 25°C
100
VDD = 5 V, 15 V
80
VDD = 2.7 V
60
40
20
0
10
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
VCC − Supply Voltage − V
100
1k
Phase
60
45
40
0
Gain
−45
20
−90
VDD=5 Vdc
RL=2 kΩ
CL=10 pF
TA=25°C
100
1k
Phase − °
90
−135
10 k
100 k 1 M
−180
10 M
GBWP − Gain Bandwidth Product − MHz
4
135
100
−40
10
1M
GAIN BANDWIDTH PRODUCT
vs
FREE-AIR TEMPERATURE
180
120
−20
100 k
Figure 14
DIFFERENTIAL VOLTAGE GAIN AND PHASE
vs
FREQUENCY
0
10 k
f − Frequency − Hz
Figure 13
80
10 k
POWER SUPPLY REJECTION RATIO
vs
FREQUENCY
TA = 125°C
0.8
1k
3.5
VDD = 15 V
3
2.5
2
VDD = 5 V
VDD = 2.7 V
1.5
1
0.5
0
−40 −25 −10 5
20 35 50 65 80 95 110 125
TA − Free-Air Temperature − °C
f − Frequency − Hz
Figure 16
Figure 15
WWW.TI.COM
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
100 k
f − Frequency − Hz
Figure 12
PSRR − Power Supply Rejection Ratio − dB
I DD − Supply Current − mA/Ch
VDD = 5 V
Figure 11
1
AVD − Differential Voltage Gain − dB
AV = −10
RL = 2 kΩ
CL = 10 pF
TA = 25°C
THD = 5%
10
100 120 140 160
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
10
VDD = 15 V
IOH − High-Level Output Current − mA
Figure 10
0.9
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
1M
10 M
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005
TYPICAL CHARACTERISTICS
SLEW RATE
vs
FREE-AIR TEMPERATURE
3.5
3
100
SR−
SR+
1
AV = 1
RL = 10 kΩ
CL = 50 pF
TA = 25°C
0.5
8.5
10.5
12.5
1.5
VDD = 5 V
AV = 1
RL = 10 kΩ
CL = 50 pF
VI = 3 V
1
0
−40 −25 −10 5
14.5
50
40
Rnull = 0
30
Rnull = 50
20
10
0
20 35 50 65 80 95 110 125
10
100
CL − Capacitive Load − pF
Figure 18
Figure 17
1000
Figure 19
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
VOLTAGE-FOLLOWER LARGE-SIGNAL
PULSE RESPONSE
100
V − Input Voltage − V
I
Hz
Rnull = 100
60
TA − Free-Air Temperature − °C
VCC − Supply Voltage −V
VDD = 2.7, 5, 15 V
TA = 25°C
90
70
80
70
60
50
4
3
2
1
VDD = 5 V
AV = 1
RL = 2 kΩ
CL = 10 pF
VI = 3 VPP
TA = 25°C
VI
0
4
40
3
30
2
20
1
VO
10
0
0
10
100
1k
10 k
f − Frequency − Hz
100 k
0
2
VOLTAGE-FOLLOWER LARGE-SIGNAL
PULSE RESPONSE
V − Input Voltage − mV
I
9
VDD = 15 V
AV = 1
RL = 2 kΩ
CL = 10 pF
VI = 9 VPP
TA = 25°C
0
VI
12
9
6
3
VO
0
0
2
4
6
8
8
10 12 14 16 18
VOLTAGE-FOLLOWER SMALL-SIGNAL
PULSE RESPONSE
12
3
6
Figure 21
Figure 20
6
4
t − Time − µs
0.12
0.08
0.04
0
VI
VDD = 5 V
AV = 1
RL = 2 kΩ
CL = 10 pF
VI = 100 mVPP
TA = 25°C
0.12
0.08
0.04
VO
0
10 12 14 16 18
0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8
t − Time − µs
t − Time − µs
Figure 22
Figure 23
WWW.TI.COM
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
V − Output Voltage − mV
O
6.5
SR+
V − Output Voltage − V
O
4.5
V n − Equivalent Input Noise Voltage − nV/
2.5
2
0.5
0
80
SR−
2.5
Phase Margin − °
SR − Slew Rate − V/ µs
1.5
V − Input Voltage − V
I
SR − Slew Rate − V/ µs
2
VDD = 5 V
RL= 2 kΩ
TA = 25°C
AV = Open Loop
90
3
2.5
PHASE MARGIN
vs
CAPACITIVE LOAD
V − Output Voltage − V
O
SLEW RATE
vs
SUPPLY VOLTAGE
11
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005
TYPICAL CHARACTERISTICS
INVERTING LARGE-SIGNAL RESPONSE
VI
3
VDD = 5 V
AV = 1
RL = 2 kΩ
CL = 10 pF
VI = 3 VPP
TA = 25°C
2
1
0
3
2
1
0
VO
0
2
4
6
8
10
12
14
12
9
VDD = 15 V
AV = −1
RL = 2 kΩ
CL = 10 pF
VI = 9 Vpp
TA = 25°C
6
3
0
0
16
0
2
4
VDD = 5 V
AV = −1
RL = 2 kΩ
CL = 10 pF
VI = 100 mVpp
TA = 25°C
16
0.1
VO
0.5 1 1.5 2 2.5 3 3.5 4 4.5
−60
−80
Crosstalk in Shutdown
−100
−120
Crosstalk
−140
10
I DD − Shutdown Supply Current − µ A/Ch
160
VDD = 2.7 V, 5 V & 15 V
VI = VDD /2
RL = 2 kΩ
CL= 10 pF
AV = 1
TA = 25°C
80
60
40
20
1k
10 k 100 k 1 M
f − Frequency − Hz
Figure 28
1M
SHUTDOWN PIN LEAKAGE CURRENT
vs
SHUTDOWN PIN VOLTAGE
SHUTDOWN SUPPLY CURRENT
vs
SUPPLY VOLTAGE
50
45
40
SHDN = 0 V
VI = VDD/2
AV = 1
TA = 125°C
35
30
TA = 70°C
25
TA = 25°C
20
15
10
TA = 0°C
TA = −40°C
5
0
0
100 k
Figure 27
Figure 26
SHUTDOWN FORWARD AND
REVERSE ISOLATION
vs
FREQUENCY
100
1k
10 k
f − Frequency −Hz
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
VDD − Supply Voltage − V
Figure 29
WWW.TI.COM
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
I DD − Shutdown Pin Leakage Current − pA
0
−40
VI
Crosstalk − dB
0.05
V O − Output Voltage − V
V I − Input Voltage − V
14
VDD = 2.7, 5, & 15 V
VI = VDD/2
AV = 1
RL = 2 kΩ
TA = 25°C
−20
t − Time − µs
Shutdown Forward and Reverse Isolation − dB
12
CROSSTALK
vs
FREQUENCY
0.10
0
12
10
0
0
100
8
Figure 25
0.05
10
6
t − Time − µs
INVERTING SMALL-SIGNAL RESPONSE
100
6
3
Figure 24
120
9
VO
t − Time − µs
140
VI
V O − Output Voltage − V
V I − Input Voltage − V
4
VO − Output Voltage − V
V − Input Voltage − V
I
INVERTING LARGE-SIGNAL RESPONSE
250
TA = 125°C
200
150
100
50
0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Shutdown Pin Voltage − V
Figure 30
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005
SHUTDOWN SUPPLY CURRENT/OUTPUT VOLTAGE
vs
TIME
SHUTDOWN SUPPLY CURRENT/OUTPUT VOLTAGE
vs
TIME
10
6
VDD = 15 V
AV = 1
RL = 2 kΩ
CL = 10 pF
VI = VDD/2
TA = 25° C
8
6
4
SHDN − Shutdown Pulse − V
SHDN − Shutdown Pulse − V
TYPICAL CHARACTERISTICS
SHDN
2
0
5
VDD = 5 V
AV = 1
RL = 2 kΩ
CL = 10 pF
VI = VDD/2
TA = 25° C
4
3
2
SHDN
1
0
V O − Output Voltage − V
6
VO
4.5
3
1.5
0
I DD − Supply Current − mA/Ch
I DD − Supply Current − mA/Ch
V O − Output Voltage − V
7.5
−1.5
1
0.75
IDD(SHDN = 0)
0.50
0.25
0
−0.25
−40
−20
0
20
40
60
80
100
120
140
2.5
1.5
1
0.5
0
−0.5
−1.0
1
0.75
0.50
IDD(SHDN = 0)
0.25
0
−0.25
−2
160
VO
2
−1
0
1
2
3
4
5
6
7
8
9
10
t − Time − µs
t − Time − µs
Figure 32
Figure 31
WWW.TI.COM
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
13
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005
APPLICATION INFORMATION
rail-to-rail input operation
The TLV237x input stage consists of two differential transistor pairs, NMOS and PMOS, that operate together
to achieve rail-to-rail input operation. The transition point between these two pairs can be seen in Figure 1,
Figure 2, and Figure 3 for a 2.7-V, 5-V, and 15-V supply. As the common-mode input voltage approaches the
positive supply rail, the input pair switches from the PMOS differential pair to the NMOS differential pair. This
transition occurs approximately 1.35 V from the positive rail and results in a change in offset voltage due to
different device characteristics between the NMOS and PMOS pairs. If the input signal to the device is large
enough to swing between both rails, this transition results in a reduction in common-mode rejection ratio
(CMRR). If the input signal does not swing between both rails, it is best to bias the signal in the region where
only one input pair is active. This is the region in Figure 1 through Figure 3 where the offset voltage varies slightly
across the input range and optimal CMRR can be achieved. This has the greatest impact when operating from
a 2.7-V supply voltage.
driving a capacitive load
When the amplifier is configured in this manner, capacitive loading directly on the output decreases the device’s
phase margin leading to high frequency ringing or oscillations. Therefore, for capacitive loads of greater than
10 pF, it is recommended that a resistor be placed in series (RNULL) with the output of the amplifier, as shown
in Figure 33. A minimum value of 20 Ω should work well for most applications.
RF
RG
RNULL
−
Input
Output
+
CLOAD
VDD/2
Figure 33. Driving a Capacitive Load
offset voltage
The output offset voltage, (VOO) is the sum of the input offset voltage (VIO) and both input bias currents (IIB) times
the corresponding gains. The following schematic and formula can be used to calculate the output offset
voltage:
RF
IIB−
RG
+
−
VI
IIB+
V
OO
+V
IO
ǒ ǒ ǓǓ
1)
R
R
F
G
VO
+
RS
"I
IB)
R
S
ǒ ǒ ǓǓ
1)
R
R
F
G
"I
IB–
Figure 34. Output Offset Voltage Model
14
WWW.TI.COM
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
R
F
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005
APPLICATION INFORMATION
general configurations
When receiving low-level signals, limiting the bandwidth of the incoming signals into the system is often
required. The simplest way to accomplish this is to place an RC filter at the noninverting terminal of the amplifier
(see Figure 35).
RG
RF
VDD/2
−
VO
+
VI
R1
C1
f
V
O +
V
I
ǒ
1)
R
R
F
G
+
–3dB
Ǔǒ
1
2pR1C1
Ǔ
1
1 ) 2pfR1C1
Figure 35. Single-Pole Low-Pass Filter
If even more attenuation is needed, a multiple pole filter is required. The Sallen-Key filter can be used for this
task. For best results, the amplifier should have a bandwidth that is 8 to 10 times the filter frequency bandwidth.
Failure to do this can result in phase shift of the amplifier.
C1
+
_
VI
R1
R1 = R2 = R
C1 = C2 = C
Q = Peaking Factor
(Butterworth Q = 0.707)
R2
f
C2
RF
RG
–3dB
RG =
+
(
1
2pRC
RF
1
2−
Q
)
VDD/2
Figure 36. 2-Pole Low-Pass Sallen-Key Filter
WWW.TI.COM
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
15
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005
APPLICATION INFORMATION
circuit layout considerations
To achieve the levels of high performance of the TLV237x, follow proper printed-circuit board design techniques.
A general set of guidelines is given in the following.
D Ground planes—It is highly recommended that a ground plane be used on the board to provide all
components with a low inductive ground connection. However, in the areas of the amplifier inputs and
output, the ground plane can be removed to minimize the stray capacitance.
D Proper power supply decoupling—Use a 6.8-µF tantalum capacitor in parallel with a 0.1-µF ceramic
capacitor on each supply terminal. It may be possible to share the tantalum among several amplifiers
depending on the application, but a 0.1-µF ceramic capacitor should always be used on the supply terminal
of every amplifier. In addition, the 0.1-µF capacitor should be placed as close as possible to the supply
terminal. As this distance increases, the inductance in the connecting trace makes the capacitor less
effective. The designer should strive for distances of less than 0.1 inches between the device power
terminals and the ceramic capacitors.
D Sockets—Sockets can be used but are not recommended. The additional lead inductance in the socket pins
will often lead to stability problems. Surface-mount packages soldered directly to the printed-circuit board
is the best implementation.
D Short trace runs/compact part placements—Optimum high performance is achieved when stray series
inductance has been minimized. To realize this, the circuit layout should be made as compact as possible,
thereby minimizing the length of all trace runs. Particular attention should be paid to the inverting input of
the amplifier. Its length should be kept as short as possible. This helps to minimize stray capacitance at the
input of the amplifier.
D Surface-mount passive components—Using surface-mount passive components is recommended for high
performance amplifier circuits for several reasons. First, because of the extremely low lead inductance of
surface-mount components, the problem with stray series inductance is greatly reduced. Second, the small
size of surface-mount components naturally leads to a more compact layout thereby minimizing both stray
inductance and capacitance. If leaded components are used, it is recommended that the lead lengths be
kept as short as possible.
shutdown function
Three members of the TLV237x family (TLV2370/3/5) have a shutdown terminal for conserving battery life in
portable applications. When the shutdown terminal is tied low, the supply current is reduced to 25 µA/channel,
the amplifier is disabled, and the outputs are placed in a high impedance mode. To enable the amplifier, the
shutdown terminal can either be left floating or pulled high. When the shutdown terminal is left floating, care
should be taken to ensure that parasitic leakage current at the shutdown terminal does not inadvertently place
the operational amplifier into shutdown.
16
WWW.TI.COM
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005
APPLICATION INFORMATION
general power dissipation considerations
For a given θJA, the maximum power dissipation is shown in Figure 37 and is calculated by the following formula:
P
D
+
Where:
ǒ
T
Ǔ
–T
MAX A
q
JA
PD = Maximum power dissipation of TLV237x IC (watts)
TMAX = Absolute maximum junction temperature (150°C)
TA
= Free-ambient air temperature (°C)
θJA = θJC + θCA
θJC = Thermal coefficient from junction to case
θCA = Thermal coefficient from case to ambient air (°C/W)
MAXIMUM POWER DISSIPATION
vs
FREE-AIR TEMPERATURE
2
Maximum Power Dissipation − W
1.75
PDIP Package
Low-K Test PCB
θJA = 104°C/W
1.5
1.25
TJ = 150°C
MSOP Package
Low-K Test PCB
θJA = 260°C/W
SOIC Package
Low-K Test PCB
θJA = 176°C/W
1
0.75
0.5
0.25
SOT-23 Package
Low-K Test PCB
θJA = 324°C/W
0
−55 −40 −25 −10 5
20 35 50 65 80 95 110 125
TA − Free-Air Temperature − °C
NOTE A: Results are with no air flow and using JEDEC Standard Low-K test PCB.
Figure 37. Maximum Power Dissipation vs Free-Air Temperature
WWW.TI.COM
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
17
PACKAGE OPTION ADDENDUM
www.ti.com
11-Dec-2006
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLV2370ID
ACTIVE
SOIC
D
8
TLV2370IDBVR
ACTIVE
SOT-23
DBV
TLV2370IDBVRG4
ACTIVE
SOT-23
TLV2370IDBVT
ACTIVE
TLV2370IDBVTG4
75
Lead/Ball Finish
MSL Peak Temp (3)
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
6
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
DBV
6
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SOT-23
DBV
6
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
ACTIVE
SOT-23
DBV
6
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2370IDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2370IDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2370IDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2370IP
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2370IPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2371ID
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2371IDBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2371IDBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2371IDBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2371IDBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2371IDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2371IDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2371IDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2371IP
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
Call TI
N / A for Pkg Type
TLV2371IPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
Call TI
N / A for Pkg Type
TLV2372ID
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2372IDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2372IDGK
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2372IDGKG4
ACTIVE
MSOP
DGK
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2372IDGKR
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
11-Dec-2006
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLV2372IDGKRG4
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2372IDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2372IDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2372IP
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2372IPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2373ID
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2373IDG4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2373IDGS
ACTIVE
MSOP
DGS
10
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2373IDGSG4
ACTIVE
MSOP
DGS
10
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2373IDGSR
ACTIVE
MSOP
DGS
10
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2373IDGSRG4
ACTIVE
MSOP
DGS
10
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2373IDR
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2373IDRG4
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2373IN
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2373INE4
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2374ID
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2374IDG4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2374IDR
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2374IDRG4
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2374IN
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2374INE4
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2374IPW
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2374IPWG4
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2374IPWR
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2374IPWRG4
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2375D
PREVIEW
SOIC
D
16
Addendum-Page 2
TBD
Lead/Ball Finish
Call TI
MSL Peak Temp (3)
Call TI
PACKAGE OPTION ADDENDUM
www.ti.com
11-Dec-2006
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLV2375DR
PREVIEW
SOIC
D
16
TBD
Call TI
TLV2375ID
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2375IDG4
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2375IDR
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2375IDRG4
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2375IN
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2375INE4
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLV2375IPW
ACTIVE
TSSOP
PW
16
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2375IPWG4
ACTIVE
TSSOP
PW
16
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2375IPWR
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2375IPWRG4
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
Call TI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 3
MECHANICAL DATA
MPDI001A – JANUARY 1995 – REVISED JUNE 1999
P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE
0.400 (10,60)
0.355 (9,02)
8
5
0.260 (6,60)
0.240 (6,10)
1
4
0.070 (1,78) MAX
0.325 (8,26)
0.300 (7,62)
0.020 (0,51) MIN
0.015 (0,38)
Gage Plane
0.200 (5,08) MAX
Seating Plane
0.010 (0,25) NOM
0.125 (3,18) MIN
0.100 (2,54)
0.021 (0,53)
0.015 (0,38)
0.430 (10,92)
MAX
0.010 (0,25) M
4040082/D 05/98
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Low Power Wireless www.ti.com/lpw
Mailing Address:
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2006, Texas Instruments Incorporated