TI TPS2300IPW

TPS2300
TPS2301
www.ti.com
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
DUAL HOT-SWAP POWER CONTROLLERS WITH INDEPENDENT CIRCUIT BREAKER AND
POWER-GOOD REPORTING
Check for Samples: TPS2300, TPS2301
FEATURES
1
•
•
•
•
•
•
•
•
•
•
Dual-Channel High-Side MOSFET Drivers
IN1: 3 V to 13 V; IN2: 3 V to 5.5 V
Output dV/dt Control Limits Inrush Current
Circuit-Breaker With Programmable
Overcurrent Threshold and Transient Timer
Power-Good Reporting With Transient Filter
CMOS- and TTL-Compatible Enable Input
Low, 5-μA Standby Supply Current (Max)
Available in 20-Pin TSSOP Package
40°C to 85°C Ambient Temperature Range
Electrostatic Discharge Protection
PW PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
8
9
10
GATE1
GATE2
DGND
TIMER
VREG
VSENSE2
VSENSE1
AGND
ISENSE2
ISENSE1
20
19
18
17
16
15
14
13
12
11
DISCH1
DISCH2
ENABLE
PWRGD1
FAULT
ISET1
ISET2
PWRGD2
IN2
IN1
NOTE: Terminal 18 is active high on TPS2301.
typical application
APPLICATIONS
VO1
+
V1
•
•
•
Hot-Swap/Plug/Dock Power Management
Hot-Plug PCI, Device Bay
Electronic Circuit Breaker
3 V − 13 V
IN1
ISET1
The TPS2300 and TPS2301 are dual-channel hotswap controllers that use external N-channel
MOSFETs as high-side switches in power
applications. Features of these devices, such as
overcurrent protection (OCP), inrush current control,
output-power status reporting, and the ability to
discriminate between load transients and faults, are
critical requirements for hot-swap applications.
DISCH1
VSENSE1
AGND
DESCRIPTION
ISENSE1 GATE1
VREG
TPS2300
PWRGD1
DGND
FAULT
TIMER
PWRGD2
ENABLE
IN2
ISET2
ISENSE2
GATE2
DISCH2
VSENSE2
VO2
+
V2
3 V − 5.5 V
The TPS2300/01 devices incorporate undervoltage lockout (UVLO) and power-good (PG) reporting to ensure the
device is off at start-up and confirm the status of the output voltage rails during operation. Each internal charge
pump, capable of driving multiple MOSFETs, provides enough gate-drive voltage to fully enhance the N-channel
MOSFETs. The charge pumps control both the rise times and fall times (dv/dt) of the MOSFETs, reducing power
transients during power up/down. The circuit-breaker functionality combines the ability to sense overcurrent
conditions with a timer function; this allows designs such as DSPs, that may have high peak currents during
power-state transitions, to disregard transients for a programmable period.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2000–2013, Texas Instruments Incorporated
TPS2300
TPS2301
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
www.ti.com
Table 1. AVAILABLE OPTIONS
40°C to 85°C
(1)
TSSOP PACKAGES (PW, PWR) (1)
PIN
COUNT
ENABLE
ENABLE
Dual-channel with independent OCP and adjustable PG
20
TPS2300IPW
TPS2301IPW
Dual-channel with interdependent OCP and adjustable PG
20
TPS2310IPW
TPS2311IPW
Dual-channel with independent OCP
16
TPS2320IPW
TPS2321IPW
Single-channel with OCP and adjustable PG
14
TPS2330IPW
TPS2331IPW
TA
HOT-SWAP CONTROLLER DESCRIPTION
The packages are available left-end taped and reeled (indicated by the R suffix on the device type; e.g., TPS2301IPWR).
FUNCTIONAL BLOCK DIAGRAM
IN1
VREG
ISET1
ISENSE1
GATE1
PREREG
DISCH1
Clamp
dv/dt Rate
Protection
50 µA
Circuit
Breaker
Charge
Pump
Pulldown FET
Circuit Breaker
UVLO and
Power Up
AGND
VSENSE1
75 µA
PWRGD1
Deglitcher
DGND
ENABLE
FAULT
Logic
Deglitcher
TIMER
PWRGD2
Second Channel
IN2
ISET2
ISENSE2 GATE2
DISCH2
VSENSE2
Table 2. Terminal Functions
TERMINAL
NAME
NO.
I/O
DESCRIPTION
AGND
8
I
Analog ground, connects to DGND as close as possible
DGND
3
I
Digital ground
DISCH1
20
O
Discharge transistor 1
DISCH2
19
O
Discharge transistor 2
ENABLE/ ENABLE
18
I
Active low (TPS2300) or active high enable (TPS2301)
FAULT
16
O
Overcurrent fault, open-drain output
GATE1
1
O
Connects to gate of channel 1 high-side MOSFET
GATE2
2
O
Connects to gate of channel 2 high-side MOSFET
IN1
11
I
Input voltage for channel 1
IN2
12
I
Input voltage for channel 2
ISENSE1
10
I
Current-sense input channel 1
ISENSE2
9
I
Current-sense input channel 2
ISET1
15
I
Adjusts circuit-breaker threshold with resistor connected to IN1
2
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
TPS2300
TPS2301
www.ti.com
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
Table 2. Terminal Functions (continued)
TERMINAL
NAME
NO.
I/O
DESCRIPTION
ISET2
14
I
Adjusts circuit-breaker threshold with resistor connected to IN2
PWRGD1
17
O
Open-drain output, asserted low when VSENSE1 voltage is less than reference.
PWRGD2
13
O
Open-drain output, asserted low when VSENSE2 voltage is less than reference.
TIMER
4
O
Adjusts circuit-breaker deglitch time
VREG
5
O
Connects to bypass capacitor, for stable operation
VSENSE1
7
I
Power-good sense input channel 1
VSENSE2
6
I
Power-good sense input channel 2
DETAILED DESCRIPTION
DISCH1, DISCH2 – DISCH1 and DISCH2 should be connected to the sources of the external N-channel
MOSFET transistors connected to GATE1 and GATE2, respectively. These pins discharge the loads when the
MOSFET transistors are disabled. They also serve as reference-voltage connections for internal gate voltageclamp circuitry.
ENABLE or ENABLE – ENABLE for TPS2300 is active-low. ENABLE for TPS2301 is active-high. When the
controller is enabled, both GATE1 and GATE2 voltages powers up to turn on the external MOSFETs. When the
ENABLE pin is pulled high for TPS2300 or the ENABLE pin is pulled low for TPS2301 for more than 50 µs, the
gate of the MOSFET is discharged at a controlled rate by a current source, and a transistor is enabled to
discharge the output bulk capacitance. In addition, the device turns on the internal regulator PREREG (see
VREG) when enabled and shuts down PREREG when disabled so that total supply current is less than 5 μA.
FAULT – FAULT is an open-drain overcurrent flag output. When an overcurrent condition in either channel is
sustained long enough to charge TIMER to 0.5 V, the overcurrent channel latches off and pulls this pin low. The
other channel runs normally if not in overcurrent. In order to turn the channel back on, either the enable pin has
to be toggled or the input power has to be cycled.
GATE1, GATE2 – GATE1 and GATE2 connect to the gates of external N-channel MOSFET transistors. When
the device is enabled, internal charge-pump circuitry pulls these pins up by sourcing approximately 15 μA to
each. The turnon slew rates depend upon the capacitance present at the GATE1 and GATE2 terminals. If
desired, the turnon slew rates can be further reduced by connecting capacitors between these pins and ground.
These capacitors also reduce inrush current and protect the device from false overcurrent triggering during
power up. The charge-pump circuitry generates gate-to-source voltages of 9 V–12 V across the external
MOSFET transistors.
IN1, IN2 – IN1 and IN2 should be connected to the power sources driving the external N-channel MOSFET
transistors connected to GATE1 and GATE2, respectively. The TPS2300/TPS2301 draws its operating current
from IN1, and both channels remains disabled until the IN1 power supply has been established. The IN1 channel
has been constructed to support 3-V, 5-V, or 12-V operation, while the IN2 channel has been constructed to
support 3-V or 5-V operation
ISENSE1, ISENSE2, ISET1, ISET2 – ISENSE1 and ISENSE2, in combination with ISET1 and ISET2, implement
overcurrent sensing for GATE1 and GATE2. ISET1 and ISET2 set the magnitude of the current that generates
an overcurrent fault, through external resistors connected to ISET1 and ISET2. An internal current source draws
50 μA from ISET1 and ISET2. With a sense resistor from IN1 to ISENSE1 or from IN2 to ISENSE2, which is also
connected to the drains of external MOSFETs, the voltage on the sense resistor reflects the load current. An
overcurrent condition is assumed to exist if ISENSE1 is pulled below ISET1 or if ISENSE2 is pulled below ISET2.
To ensure proper circuit breaker operation, VI(ISENSE1) and VI(ISET1) should never exceed VI(IN1). Similarly,
VI(ISENSE2) and VI(ISET2) should never exceed VI(IN2).
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
3
TPS2300
TPS2301
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
www.ti.com
PWRGD1, PWRGD2 – PWRGD1 and PWRGD2 signal the presence of undervoltage conditions on VSENSE1
and VSENSE2, respectively. These pins are open-drain outputs and are pulled low during an undervoltage
condition. To minimize erroneous PWRGDx responses from transients on the voltage rail, the voltage sense
circuit incorporates a 20-μs deglitch filter. When VSENSEx is lower than the reference voltage (about 1.23 V),
PWRGDx is active low to indicate an undervoltage condition on the power-rail voltage. PWRGDx may not
correctly report power conditions when the device is disabled, because there is no gate drive power for the
PWRGD output transistor in the disable mode, or, in other words, PWRGD is floating. Therefore, PWRGD is
pulled up to its pullup power supply rail in disable mode.
TIMER – A capacitor on TIMER sets the time during which the power switch can be in overcurrent before turning
off. When the overcurrent protection circuits sense an excessive current, a current source is enabled which
charges the capacitor on TIMER. Once the voltage on TIMER reaches approximately 0.5 V, the circuit-breaker
latch is set and the power switch is latched off. Power must be recycled or the ENABLE pin must be toggled to
restart the controller. In high-power or high-temperature applications, a minimum 50-pF capacitor is strongly
recommended from TIMER to ground, to prevent any false triggering.
VREG – VREG is the output of an internal low-dropout voltage regulator, where IN1 is the input. The regulator is
used to generate a regulated voltage source, less than 5.5 V, for the device. A 0.1-μF ceramic capacitor should
be connected between VREG and ground to aid in noise rejection. In this configuration, upon disabling the
device, the internal low-dropout regulator will also be disabled, which removes power from the internal circuitry
and allows the device to be placed in low-quiescent-current mode. In applications where IN1 is less than 5.5 V,
VREG and IN1 may be connected together. However, under these conditions, disabling the device does not
place the device in low-quiescent-current mode, because the internal low-dropout voltage regulator is being
bypassed, thereby keeping internal circuitry operational. If VREG and IN1 are connected together, a 0.1-μF
ceramic capacitor between VREG and ground is not needed if IN1 already has a bypass capacitor of 1 μF to
10 μF.
VSENSE1, VSENSE2 – VSENSE1 and VSENSE2 can be used to detect undervoltage conditions on external
circuitry. If VSENSE1 senses a voltage below approximately 1.23 V, PWRGD1 is pulled low. Similarly, a voltage
less than 1.23 V on VSENSE2 causes PWRGD2 to be pulled low.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted)
Input voltage range
Output voltage range
Sink current range
(1) (2)
VALUE
UNIT
VI(IN1), VI(ISENSE1), VI(VSENSE1), VI(VSENSE2), VI(ISET1), VI(ENABLE), VI(VREG)
–0.3 to 15
V
VI(IN2), VI(ISENSE2), VI(ISET2)
–0.3 to 7
V
VO(GATE1)
–0.3 to 30
V
VO(GATE2)
–0.3 to 22
V
VO(DISCH1), VO(PWRGD1), VO(PWRGD2), VO(FAULT), VO(DISCH2), VO(TIMER)
–0.3 to 15
V
0 to 100
mA
I(GATE1), I(GATE2), I(DISCH1), I(DISCH2)
0 to 10
mA
Operating virtual junction temperature range, TJ
I(PWRGD1), I(PWRGD2), I(TIMER), I(FAULT)
–40 to 100
°C
Storage temperature range, Tstg
–55 to 150
°C
260
°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds
(1)
(2)
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are respect to DGND.
DISSIPATION RATING TABLE
4
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
PW-20
1015 mW
13.55 mW/°C
406 mW
203 mW
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
TPS2300
TPS2301
www.ti.com
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
RECOMMENDED OPERATING CONDITIONS
MIN
VI(IN1), VI(ISENSE1), VI(VSENSE1), VI(VSENSE2), VI(ISET1)
3
VI(IN2), VI(ISENSE2), VI(ISET2), VI(VREG)
3
VI
Input voltage
TJ
Operating virtual junction temperature
NOM
MAX
UNIT
13
5.5
VI(ISENSE1), VI(ISET1), VI(VSENSE1)
VI(IN1)
VI(ISENSE2), VI(ISET2), VI(VSENSE2)
V
VI(IN2)
–40
100
°C
ELECTRICAL CHARACTERISTICS
over recommended operating temperature range (–40°C < TA < 85°C), 3 V ≤ VI(IN1) ≤13 V, 3 V ≤ VI(IN2) ≤ 5.5 V (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
GENERAL
II(IN1)
Input current, IN1
VI(ENABLE) = 5 V (TPS2301),
0.5
1
mA
II(IN2)
Input current, IN2
VI(ENABLE) = 0 V (TPS2300)
75
200
µA
II(stby)
Standby current (sum of
currents into IN1, IN2,
ISENSE1, ISENSE2,
ISET1, and ISET2)
VI(ENABLE) = 0 V (TPS2301),
VI(ENABLE) = 5 V (TPS2300)
5
µA
Gate voltage
II(GATE1) = 500 nA,
DISCH1 open
GATE1
VG(GATE1_3V)
VG(GATE1_4.5V)
VI(IN1) = 3 V
VG(GATE1_10.8V)
9
11.5
VI(IN1) = 4.5 V
10.5
14.5
VI(IN1) = 10.8 V
16.8
21
9
10
12
V
V
VC(GATE1)
Clamping voltage, GATE1
to DISCH1
IS(GATE1)
Source current, GATE1
3 V ≤ VI(IN1) ≤ 13.2 V, 3 V ≤ VO(VREG) ≤ 5.5 V,
VI(GATE1) = VI(IN1) + 6 V
10
14
20
μA
Sink current, GATE1
3 V ≤ VI(IN1) ≤ 13.2 V, 3 V ≤ VO(VREG) ≤ 5.5 V,
VI(GATE1) = VI(IN1)
50
75
100
µA
Rise time, GATE1
Cg to GND = 1 nF (1)
tr(GATE1)
VI(IN1) = 3 V
0.5
VI(IN1) = 4.5 V
0.6
VI(IN1) = 10.8 V
VI(IN1) = 3 V
tf(GATE1)
Fall time, GATE1
Cg to GND = 1 nF
(1)
ms
1
0.1
VI(IN1) = 4.5 V
0.12
VI(IN1) = 10.8 V
0.2
ms
GATE2
VG(GATE2_3V)
VG(GATE2_4.5V)
Gate voltage
VI(IN2) = 3 V
II(GATE2) = 500 nA,
DISCH2 open
VI(IN2) = 4.5 V
9
11.7
10.5
14.7
9
10
12
V
V
VC(GATE2)
Clamping voltage, GATE2
to DISCH2
IS(GATE2)
Source current, GATE2
3 V ≤ VI(IN2) ≤ 5.5 V, 3 V ≤ VO(VREG) ≤ 5.5 V,
VI(GATE2) = VI(IN2) + 6 V
10
14
20
µA
Sink current, GATE2
3 V ≤ VI(IN2) ≤ 5.5 V, 3 V ≤ VO(VREG) ≤ 5.5 V,
VI(GATE2) = VI(IN2)
50
75
100
µA
Rise time, GATE2
Cg to GND = 1 nF (1)
tr(GATE2)
tf(GATE2)
(1)
Fall time, GATE2
Cg to GND = 1 nF (1)
VI(IN2) = 3 V
VI(IN2) = 4.5 V
VI(IN2) = 3 V
0.5
VO(VREG) = 3 V
VI(IN2) = 4.5 V
0.6
0.1
0.12
ms
ms
Specified, but not production tested.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
5
TPS2300
TPS2301
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
www.ti.com
ELECTRICAL CHARACTERISTICS (Continued)
over recommended operating temperature range (–40°C < TA < 85°C), 3V ≤VI(IN1) ≤13V, 3V ≤ VI(IN2) ≤ 5.5V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
TIMER
V(TO_TIMER)
Threshold voltage, TIMER
0.4
0.5
0.6
V
VI(TIMER) = 0 V
35
50
65
µA
Discharge current, TIMER VI(TIMER) = 1 V
1
2.5
RISETx = 1 kΩ
40
50
60
RISETx = 400 Ω, TA = 25°C
14
19
24
RISETx = 1 kΩ, TA = 25°C
44
50
53
RISETx = 1.5 kΩ, TA = 25°C
68
73
78
0.1
5
Charge current, TIMER
mA
CIRCUIT BREAKER
VIT(CB)
Threshold voltage, circuit
breaker
I(IB_ISENSEx)
Input bias current, ISENSEx
Discharge current, GATEx
Propagation (delay) time,
comparator inputs to gate
output
tpd(CB)
VO(GATEx) = 4 V
400
800
VO(GATEx) = 1 V
25
150
Cg = 50 pF,
(50% to 10%),
10 mV overdrive,
CTIMER = 50 pF
mV
µA
mA
1.3
µs
ENABLE, ACTIVE LOW (TPS2300)
VIH(ENABLE)
High-level input voltage,
ENABLE
VIL(ENABLE)
Low-level input voltage,
ENABLE
RI(ENABLE)
Input pullup resistance,
ENABLE
See
td(off_ENABLE)
Turnoff delay time,
ENABLE
VI(ENABLE) increasing above stop threshold;
100 ns rise time, 20 mV overdrive (2)
60
μs
td(on_ENABLE)
Turnon delay time,
ENABLE
VI(ENABLE) decreasing below start threshold;
100 ns fall time, 20 mV overdrive (2)
125
μs
2
(1)
100
V
200
0.8
V
300
kΩ
ENABLE, ACTIVE HIGH (TPS2301)
VIH(ENABLE)
High-level input voltage,
ENABLE
VIL(ENABLE)
Low-level input voltage,
ENABLE
RI(ENABLE)
Input pulldown resistance,
ENABLE
td(on_ENABLE)
Turnon delay time,
ENABLE
VI(ENABLE) increasing above start threshold;
100 ns rise time, 20 mV overdrive (2)
85
μs
td(off_ENABLE)
Turnoff delay time,
ENABLE
VI(ENABLE) decreasing below stop threshold;
100 ns fall time, 20 mV overdrive (2)
100
µs
V(VREG)
PREREG output voltage
4.5 ≤ VI(IN1) ≤ 13 V
V(drop_PREREG)
PREREG dropout voltage
VI(IN1) = 3 V
2
100
V
150
0.7
V
300
kΩ
PREREG
(1)
(2)
6
3.5
4.1
5.5
V
0.1
V
1V
Test IO of ENABLE at VI(ENABLE) = 1 V and 0 V, then RI(ENABLE) = I
O_ 0V * I O_ 1V
Specified, but not production tested.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
TPS2300
TPS2301
www.ti.com
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
ELECTRICAL CHARACTERISTICS (Continued)
over recommended operating temperature range (–40°C < TA < 85°C), 3V ≤VI(IN1) ≤13V, 3V ≤ VI(IN2) ≤ 5.5V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
2.95
V
VREG UVLO
V(TO_UVLOstart)
Output threshold voltage,
start
2.75
2.85
V(TO_UVLOstop)
Output threshold voltage,
stop
2.65
2.78
Vhys(UVLO)
Hysteresis
50
75
UVLO sink current,
GATEx
V
mV
VI(GATEx) = 2 V
10
mA
VI(VSENSEx) decreasing
1.2
1.225
1.25
20
30
40
mV
0.2
0.4
V
PWRGD1 and PWRGD2
VIT(ISENSEx)
Trip threshold, VSENSEx
Vhys
Hysteresis voltage,
power-good comparator
V
VO(sat_PWRGDx)
Output saturation voltage,
IO = 2 mA
PWRGDx
VO(VREG_min)
Minimum VO(VREG) for
valid power-good
IO = 100 μA, VO(PWRGDx) = 1 V
1
V
Input bias current, powergood comparator
VI(VSENSEx) = 5.5 V
1
μA
Ilkg(PWRGDx)
Leakage current,
PWRGDx
VO(PWRGDx) = 13 V
1
μA
tdr
Delay time, rising edge,
PWRGDx
VI(VSENSEx) increasing, overdrive = 20 mV,
tr = 100 ns (1)
25
μs
tdf
Delay time, falling edge,
PWRGDx
VI(VSENSEx) decreasing, overdrive = 20 mV,
tr = 100 ns (1)
2
μs
FAULT OUTPUT
VO(sat_FAULT)
Output saturation voltage, IO = 2 mA
FAULT
Ilkg(FAULT)
Leakage current, FAULT
VO(FAULT) = 13 V
0.4
V
1
µA
DISCH1 AND DISCH2
I(DISCH)
Discharge current,
DISCHx
VIH(DISCH)
Discharge on high-level
input voltage
VIL(DISCH)
Discharge on low-level
input voltage
(1)
VI(DISCHx) = 1.5 V, VI(VIN1) = 5 V
5
10
mA
2
V
1
V
Specified, but not production tested.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
7
TPS2300
TPS2301
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
www.ti.com
PARAMETER MEASUREMENT INFORMATION
Load 12 W
VI(ENABLE)
5 V/div
Load 12 W
VI(ENABLE)
5 V/div
VO(GATE1)
10 V/div
VO(DISCH1)
5 V/div
VO(GATE1)
10 V/div
VO(DISCH1)
5 V/div
t – Time – 10 ms/div
t – Time – 10 ms/div
Figure 1. Turnon Voltage Transition of Channel 1
Figure 2. Turnoff Voltage Transition of Channel 1
Load 5 W
VI(ENABLE)
5 V/div
Load 5 W
VI(ENABLE)
5 V/div
VO(GATE2)
10 V/div
VO(GATE2)
10 V/div
VO(DISCH2)
5 V/div
VO(DISCH2)
5 V/div
t – Time – 10 ms/div
Figure 3. Turnon Voltage Transitioin of Channel 2
8
t – Time – 10 ms/div
Figure 4. Turnoff Voltage Transition of Channel 2
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
TPS2300
TPS2301
www.ti.com
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
PARAMETER MEASUREMENT INFORMATION (continued)
VI(ENABLE)
5 V/div
No Capacitor on Timer
VI(ENABLE)
5 V/div
VO(GATE1)
10 V/div
No Capacitor on Timer
VO(GATE1)
10 V/div
VO(FAULT)
10 V/div
VO(FAULT)
10 V/div
IO(OUT1)
2 A/div
IO(OUT1)
2 A/div
t – Time – 5 ms/div
Figure 5. Channel 1 Overcurrent Response:
Enabled Into Overcurrent Load
VI(ENABLE)
5 V/div
t – Time – 1 ms/div
Figure 6. Channel 1 Overcurrent Response:
an Overcurrent Load Plugged Into the Enabled
Board
No Capacitor on Timer
No Capacitor on Timer
VI(ENABLE)
5 V/div
VO(GATE2)
10 V/div
VO(GATE2)
10 V/div
VO(FAULT)
10 V/div
VO(FAULT)
10 V/div
IO(OUT2)
2 A/div
IO(OUT2)
2 A/div
t – Time – 2 ms/div
Figure 7. Channel 2 Overcurrent Response:
Enabled Into Overcurrent Load
t – Time – 0.5 ms/div
Figure 8. Channel 2 Overcurrent Response: an
Overcurrent Load Plugged Into the Enabled Board
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
9
TPS2300
TPS2301
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
www.ti.com
PARAMETER MEASUREMENT INFORMATION (continued)
No Capacitor on Timer
VI(ENABLE)
5 V/div
VI(ENABLE)
5 V/div
VO(GATE1)
10 V/div
VO(GATE2)
5 V/div
VO(FAULT)
10 V/div
VO(FAULT)
10 V/div
II(IN1)
2 A/div
II(IN2)
2 A/div
t – Time – 1 ms/div
t – Time – 1 ms/div
Figure 9. Channel 1 – Enabled Into Short Circuit
No Capacitor on Timer
Figure 10. Channel 1 – Enabled Into Short Circuit
VI(IN1)
10 V/div
VO(GATE1)
10 V/div
VI(IN1)
10 V/div
No Capacitor on Timer
No Capacitor on Timer
VO(GATE1)
10 V/div
VO(OUT1)
10 V/div
IO(OUT1)
1 A/div
VO(OUT1)
10 V/div
IO(OUT1)
1 A/div
t – Time – 1 ms/div
t – Time – 5 ms/div
Figure 11. Channel 1 – Hot Plug
10
Figure 12. Channel 1 – Hot Removal
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
TPS2300
TPS2301
www.ti.com
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
PARAMETER MEASUREMENT INFORMATION (continued)
No Capacitor on Timer
VI(IN2)
5 V/div
VO(GATE2)
10 V/div
VO(OUT2)
5 V/div
IO(OUT2)
1 A/div
t – Time – 5 ms/div
Figure 13. Channel 2 - Hot Plug
VI(IN2)
5 V/div
No Capacitor on Timer
VO(GATE2)
10 V/div
VO(OUT2)
5 V/div
IO(OUT2)
1 A/div
t – Time – 1 ms/div
Figure 14. Channel 2 - Hot Removal
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
11
TPS2300
TPS2301
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
www.ti.com
TYPICAL CHARACTERISTICS
INPUT CURRENT 1 (ENABLED)
vs
INPUT VOLTAGE 1
INPUT CURRENT 2 (ENABLED)
vs
INPUT VOLTAGE 2
71.5
52
IN1 = 13 V
IN2 = 5.5 V
51
TA = 85°C
TA = 0°C
71
II2 – Input Current 2 – mA
II1 – Input Current 1 – mA
50
TA = 25°C
49
48
47
TA = 0°C
46
TA = –40°C
TA = –40°C
70.5
TA = 25°C
70
TA = 85°C
69.5
69
45
68.5
44
43
4
5
6
7
8
9
10
11
12
13
68
2.5
14
3
INPUT CURRENT 1 (DISABLED)
vs
INPUT VOLTAGE 1
5
5.5
6
23
IN1 = 13 V
21
14
TA = 25°C
TA = –40°C
12
TA = 0°C
11
10
9
8
4
5
6
7
8
9
10
TA = 85°C
19
13
II2 – Input Current 2 – nA
II1 – Input Current 1 – nA
4.5
TA = 85°C
IN2 = 5.5 V
11
12
13
14
TA = –40°C
17
15
13
11
9
TA = 0°C
7
TA = 25°C
5
2.5
VI1 – Input Voltage 1 – V
Figure 17.
12
4
INPUT CURRENT 2 (DISABLED)
vs
INPUT VOLTAGE 2
15
7
3.5
VI2 – Input Voltage 2 – V
Figure 16.
VI1 – Input Voltage 1 – V
Figure 15.
Submit Documentation Feedback
3
3.5
4
4.5
5
5.5
6
VI2 – Input Voltage 2 – V
Figure 18.
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
TPS2300
TPS2301
www.ti.com
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
TYPICAL CHARACTERISTICS (continued)
GATE1 OUTPUT VOLTAGE
vs
INPUT VOLTAGE 1
GATE1 VOLTAGE RISE TIME
vs
GATE1 LOAD CAPACITANCE
18
22
20
IN1 = 12 V
TA = 25°C
TA = 85°C
tr – GATE1 Voltage Rise Time – ms
VO – GATE1 Output Voltage – V
CL(GATE1) = 1000 pF
TA = 25°C
TA = 0°C
18
TA = –40°C
16
14
12
10
2
3
4
5
6
7
8
9
10
11
15
12
9
6
3
0
12
0
VI1 – Input Voltage 1 – V
Figure 19.
3
6
9
CL(GATE1) – GATE1 Load Capacitance – nF
Figure 20.
GATE1 VOLTAGE FALL TIME
vs
GATE1 LOAD CAPACITANCE
GATE1 OUTPUT CURRENT
vs
GATE1 VOLTAGE
4
15
IN1 = 12 V
TA = 25°C
14.5
IO – GATE1 Output Current – mA
tf – GATE1 Voltage Fall Time – ms
12
3
2
1
14
TA = –40°C
TA = 85°C
13.5
TA = 25°C
13
TA = 0°C
12.5
12
11.5
IN1 = 13 V
0
0
3
6
9
12
11
14
15
CL(GATE1) – GATE1 Load Capacitance – nF
Figure 21.
16
17
18
19
20
21
22
23
24
V – GATE1 Voltage – V
Figure 22.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
13
TPS2300
TPS2301
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
www.ti.com
TYPICAL CHARACTERISTICS (continued)
CIRCUIT-BREAKER RESPONSE TIME
vs
TIMER CAPACITANCE
LOAD VOLTAGE 1 DISCHARGE TIME
vs
LOAD CAPACITANCE
320
IN1 = 12 V
TA = 25°C
t – Load Voltage 1 Discharge Time – ms
t(res) – Circuit-Breaker Response Time – ms
12
9
6
3
0
0
0.8
0.2
0.4
0.6
CTIMER – TIMER Capacitance – nF
Figure 23.
240
200
160
120
80
40
0
1
IN1 = 12 V
IO1 = 0 A
TA = 25°C
280
0
UVLO START AND STOP THRESHOLDS
vs
TEMPERATURE
2.88
VIT – PWRGDx Input Threshold – V
Vref – UVLO Start and Stop Thresholds – V
1.27
2.86
Start
2.84
2.82
2.8
Stop
2.76
2.74
1.26
Up
1.25
1.24
1.23
Down
1.22
1.21
2.72
2.7
–45–35 –25–15 –5 5 15 25 35 45 55 65 75 85 95
TA – Temperature – °C
Figure 25.
14
500
PWRGDx INPUT THRESHOLD
vs
TEMPERATURE
2.9
2.78
400
100
200
300
CL – Load Capacitance – mF
Figure 24.
1.20
–45–35 –25–15 –5 5 15 25 35 45 55 65 75 85 95
TA – Temperature – °C
Figure 26.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
TPS2300
TPS2301
www.ti.com
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
APPLICATION INFORMATION
TYPICAL APPLICATION DIAGRAM
This diagram shows a typical dual hot-swap application. The pullup resistors at PWRGD1, PWRGD2 and FAULT
should be relatively large (e.g., 100 kΩ) to reduce power loss unless they are required to drive a large load.
System
Board
RSENSE1
3 V ∼ 12 V IN1
1 µF ∼ 10 µF
+
RVSENSE1_TOP
VO1
RISET1
RVSENSE1_BOTTOM
0.1 µF
VREG IN1 ISET1 ISENSE1 GATE1 DISCH1 VSENSE1
ENABLE
ENABLE
DGND
AGND
TPS2301
FAULT
PWRGD1
PWRGD2
FAULT
PWRGD1
PWRGD2
TIMER IN2 ISET2 ISENSE2 GATE2 DISCH2 VSENSE2
VO1 or
VO2
RISET2
3 V ∼ 5 V IN2
1 µF ∼ 10 µF
VO2
RSENSE2
RVSENSE2_TOP
+
RVSENSE2_BOTTOM
Figure 27. Typical Dual Hot-Swap Application
INPUT CAPACITOR
A 0.1-μF ceramic capacitor in parallel with a 1-μF ceramic capacitor should be placed on the input power
terminals near the connector on the hot-plug board to help stabilize the voltage rails on the cards. The
TPS2300/01 does not need to be mounted near the connector or these input capacitors. For applications with
more severe power environments, a 2.2-μF or higher ceramic capacitor is recommended near the input terminals
of the hot-plug board. A bypass capacitor for IN1 and for IN2 should be placed close to the device.
OUTPUT CAPACITOR
A 0.1-μF ceramic capacitor is recommended per load on the TPS2300/01; these capacitors should be placed
close to the external FETs and to TPS2300/01. A larger bulk capacitor is also recommended on the load. The
value of the bulk capacitor should be selected based on the power requirements and the transients generated by
the application.
EXTERNAL FET
To deliver power from the input sources to the loads, each channel needs an external N-channel MOSFET. A
few widely used MOSFETs are shown in Table 3. But many other MOSFETs in the market can also be used with
TPS23xx in hot-swap systems.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
15
TPS2300
TPS2301
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
www.ti.com
Table 3. Some Available N-Channel MOSFETs
CURRENT RANGE
(A)
0 to 2
2 to 5
5 to 10
PART NUMBER
DESCRIPTION
MANUFACTURER
IRF7601
N-channel, rDS(on) = 0.035 Ω, 4.6 A, Micro-8
International Rectifier
MTSF3N03HDR2
N-channel, rDS(on) = 0.040 Ω, 4.6 A, Micro-8
ON Semiconductor
IRF7101
Dual N-channel, rDS(on) = 0.1 Ω, 2.3 A, SO-8
International Rectifier
MMSF5N02HDR2
Dual N-channel, rDS(on) = 0.04 Ω, 5 A, SO-8
ON Semiconductor
IRF7401
N-channel, rDS(on) = 0.022 Ω, 7 A, SO-8
International Rectifier
MMSF5N02HDR2
N-channel, rDS(on) = 0.025 Ω, 5 A, SO-8
ON Semiconductor
IRF7313
Dual N-channel, rDS(on) = 0.029 Ω, 5.2 A, SO-8
International Rectifier
SI4410
N-channel, rDS(on) = 0.020 Ω, 8 A, SO-8
Vishay Dale
IRLR3103
N-channel, rDS(on) = 0.019 Ω, 29 A, d-Pak
International Rectifier
IRLR2703
N-channel, rDS(on) = 0.045 Ω, 14 A, d-Pak
International Rectifier
TIMER
For most applications, a minimum capacitance of 50 pF is recommended to prevent false triggering. This
capacitor should be connected between TIMER and ground. The presence of an overcurrent condition on either
channel of the TPS2300/01 causes a 50-μA current source to begin charging this capacitor. If the overcurrent
condition persists until the capacitor has been charged to approximately 0.5 V, the TPS2300/01 latches off the
offending channels and pulls the FAULT pin low. The timer capacitor can be made as large as desired to provide
additional time delay before registering a fault condition. The time delay is approximately:
dt(sec) = CTIMER(F) × 10,000(Ω).
OUTPUT-VOLTAGE SLEW-RATE CONTROL
When enabled, the TPS2300/01 controllers supply the gates of each external MOSFET transistor with a current
of approximately 15 μA. The slew rate of the MOSFET source voltage is thus limited by the gate-to-drain
capacitance Cgd of the external MOSFET capacitor to a value approximating:
dV s
15 mA
+
C gd
dt
(1)
If a slower slew rate is desired, an additional capacitance can be connected between the gate of the external
MOSFET and ground.
VREG CAPACITOR
The internal voltage regulator connected to VREG requires an external capacitor to ensure stability. A 0.1-μF or
0.22-μF ceramic capacitor is recommended.
GATE DRIVE CIRCUITRY
The TPS2300/01 includes four separate features associated with each gate-drive terminal:
• A charging current of approximately 15 μA is applied to enable the external MOSFET transistor. This current
is generated by an internal charge pump that can develop a gate-to-source potential (referenced to DISCH1
or DISCH2) of 9 V–12 V. DISCH1 and DISCH2 must be connected to the respective external MOSFET
source terminals to ensure proper operation of this circuitry.
• A discharge current of approximately 75 μA is applied to disable the external MOSFET transistor. Once the
transistor gate voltage has dropped below approximately 1.5 V, this current is disabled and the UVLO
discharge driver is enabled instead. This feature allows the part to enter a low-current shutdown mode while
ensuring that the gates of the external MOSFET transistors remain at a low voltage.
• During a UVLO condition, the gates of both MOSFET transistors are pulled down by internal PMOS
transistors. These transistors continue to operate even if IN1 and IN2 are both at 0 V. This circuitry also helps
hold the external MOSFET transistors off when power is suddenly applied to the system.
• During an overcurrent fault condition, the external MOSFET transistor that exhibited an overcurrent condition
is rapidly turned off by an internal pulldown circuit capable of pulling in excess of 400 mA (at 4 V) from the
16
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
TPS2300
TPS2301
www.ti.com
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
pin. Once the gate has been pulled below approximately 1.5 V, this driver is disengaged and the UVLO driver
is enabled instead. If one channel experiences an overcurrent condition and the other does not, then only the
channel that is conducting excessive current is turned off rapidly. The other channel continues to operate
normally.
SETTING THE CURRENT-LIMIT CIRCUIT-BREAKER THRESHOLD
Using channel 1 as an example, the current sensing resistor RISENSE1 and the current limit setting resistor RISET1
determine the current limit of the channel, and can be calculated by the following equation:
R
50 10 –6
I LMT1 + ISET1
R ISENSE1
(2)
Typically RISENSE1 is usually very small (0.001Ω to 0.1Ω). If the trace and solder-junction resistances between the
junction of RISENSE1 and ISENSE1 and the junction of RISENSE1 and RISET1 are greater than 10% of the RISENSE1
value, then these resistance values should be added to the RISENSE1 value used in the calculation above.
The above information and calculation also apply to channel 2. Table 4 shows some of the current sense
resistors available in the market.
Table 4. Some Current Sense Resistors
CURRENT RANGE
(A)
PART NUMBER
DESCRIPTION
0 to 1
WSL-1206, 0.05 1%
0.05 Ω, 0.25 W, 1% resistor
1 to 2
WSL-1206, 0.025 1%
0.025 Ω, 0.25 W, 1% resistor
2 to 4
WSL-1206, 0.015 1%
0.015 Ω, 0.25 W, 1% resistor
4 to 6
WSL-2010, 0.010 1%
0.010 Ω, 0.5 W, 1% resistor
6 to 8
WSL-2010, 0.007 1%
0.007 Ω, 0.5 W, 1% resistor
8 to 10
WSR-2, 0.005 1%
0.005 Ω, 0.5 W, 1% resistor
MANUFACTURER
Vishay Dale
SETTING THE POWER-GOOD THRESHOLD VOLTAGE
The two feedback resistors RVSENSEx_TOP and RVSENSEx_BOT connected between VOx and ground form a resistor
divider setting the voltage at the VSENSEx pins. VSENSE1 voltage equals:
VI(SENSE1) = VO× RVSENSE1_BOT/(RVSENSE1_TOP + RVSENSE1_BOT)
This voltage is compared to an internal voltage reference (1.225 V ±2%) to determine whether the output voltage
level is within a specified tolerance. For example, given a nominal output voltage at VO1, and defining VO1_min as
the minimum required output voltage, then the feedback resistors are defined by:
VO1_min * 1.225
R VSENSE1_TOP +
R VSENSE1_BOT
1.225
(3)
Start the process by selecting a large standard resistor value for RVSENSE1_BOT to reduce power loss. Then
RVSENSE1_TOP can be calculated by inserting all of the known values into the equation above. When VO1 is lower
than VO1_min, PWRGD1 is low as long as the controller is enabled.
UNDERVOLTAGE LOCKOUT (UVLO)
The TPS2300/01 includes an undervoltage lockout (UVLO) feature that monitors the voltage present on the
VREG pin. This feature disables both external MOSFETs if the voltage on VREG drops below 2.78 V (nominal)
and re-enables normal operation when it rises above 2.85 V (nominal). Since VREG is fed from IN1 through a
low-dropout voltage regulator, the voltage on VREG tracks the voltage on IN1 within 50 mV. While the
undervoltage lockout is engaged, both GATE1 and GATE2 are held low by internal PMOS pulldown transistors,
ensuring that the external MOSFET transistors remain off at all times, even if all power supplies have fallen to
0V.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
17
TPS2300
TPS2301
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
www.ti.com
SINGLE-CHANNEL OPERATION
Some applications may require only a single external MOS transistor. Such applications should use GATE1 and
the associated circuitry (IN1, ISENSE1, ISET1, DISCH1). The IN2 pin should be grounded to disable the circuitry
associated with the GATE2 pin. The VSENSE2 and PWRGD2 circuitry is unaffected by disabling GATE2, and
may still be used if so desired.
POWER-UP CONTROL
The TPS2300/01 includes a 500 µs (nominal) start-up delay that ensures that internal circuitry has sufficient time
to start before the device begins turning on the external MOSFETs. This delay is triggered only upon the rapid
application of power to the circuit. If the power supply ramps up slowly, the undervoltage lockout circuitry
provides adequate protection against undervoltage operation.
3-CHANNEL HOT-SWAP APPLICATION
Some applications require hot-swap control of up to three voltage rails, but may not explicitly require the sensing
of the status of the output power on all three of the voltage rails. One such application is device bay, where dv/dt
control of 3.3 V, 5 V, and 12 V is required. By using channel 2 to drive both the 3.3-V and 5-V power rails and
channel 1 to drive the 12-V power rail, as is shown below, TPS2300/01 can deliver three different voltages to
three loads while monitoring the status of two of the loads.
System
Board
RSENSE1
12 V IN1
1 µF ∼ 10 µF
+
RVSENSE1_TOP
VO1
RISET1
RVSENSE1_BOTTOM
0.1 µF
VREG
IN1 ISET1 ISENSE1 GATE1 DISCH1 VSENSE1
ENABLE
ENABLE
DGND
AGND
TPS2301
FAULT
PWRGD1
PWRGD2
FAULT
PWRGD1
PWRGD2
TIMER IN2 ISET2 ISENSE2 GATE2 DISCH2 VSENSE2
RISET2
3.3 V IN2
1 µF ∼ 10 µF
VO1 or
VO2
Rg1
VO2
RSENSE2
RVSENSE2_TOP
+
Rg2
RVSENSE2_BOTTOM
5 V IN3
VO3
1 µF ∼ 10 µF
+
Figure 28. Three-Channel Application
Figure 29 shows ramp-up waveforms of the three output voltages.
18
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
TPS2300
TPS2301
www.ti.com
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
VO – Output Voltage – 2 V/div
VO1
VO3
VO2
t – Time – 2.5 ms/div
Figure 29.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
19
TPS2300
TPS2301
SLVS265H – FEBRUARY 2000 – REVISED JULY 2013
www.ti.com
REVISION HISTORY
Note: Revision history for previous versions is not available. Page numbers of previous versions may differ.
Changes from Revision G (November 2006) to Revision H
Page
•
Added text to ISENSE1, ISENSE2, ISET1, ISET2 pin description paragraph for clarification. ............................................ 3
•
Added additional VI specs to ROC table for clarification ...................................................................................................... 5
•
Added minus sign to 40°C MIN TJ temperature ................................................................................................................... 5
20
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: TPS2300 TPS2301
PACKAGE OPTION ADDENDUM
www.ti.com
13-May-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
TPS2300IPW
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
TPS2300I
TPS2300IPWG4
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
TPS2300I
TPS2300IPWR
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
TPS2300I
TPS2300IPWRG4
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
TPS2300I
TPS2301IPW
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
TPS2301I
TPS2301IPWG4
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
TPS2301I
TPS2301IPWR
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
TPS2301I
TPS2301IPWRG4
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
TPS2301I
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
13-May-2013
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated