TI TPS2341PHP

SLUS513A − MAY 2003 − REVISED JULY 2004
FEATURES
D 12-V, −12-V, 3.3-V, 5-V Main Power Switching
D
D
D
D
D
D
D
D
D
D
and Auxiliary 3.3-V Power Switching
12-V, −12-V And Auxiliary 3.3-V Power FETs
Hot-Swap Protection and Control of All
Supplies
Overcurrent Protection for All Supplies
Isolation of Any Load Fault in One Slot from
Any Other Slot
Undervoltage Monitoring for the Main 12-V,
3.3-V, 5-V and Auxiliary 3.3-V Supplies
Power Fault Latching
Overtemperature Shutdown
I2C Interface for Power Control, Power
Status, Slot Control And Slot Status
Compliant To PCI And PCI-X Hot Plug
Specifications
One TPS2341 Supports Two Slots
DESCRIPTION
The TPS2341 contains main supply power
control, auxiliary supply power control, power
FETs for 12-V, −12-V and auxiliary 3.3-V supplies,
and a serial interface for communications with and
control of slots. Each TPS2341 contains supply
control and switching for two slots.
The main power control circuits start with all
supplies off and hold all supplies off until power to
the TPS2341 is valid on all positive supplies.
When power is requested, the control circuit
applies constant current to the gates of the power
!"# $"%&! '#(
'"! ! $#!! $# )# # #* "#
'' +,( '"! $!#- '# #!#&, !&"'#
#- && $##(
FETs, allowing each FET to ramp the load voltage
linearly. Each main supply can be programmed for
a desired ramp rate by selecting a gate capacitor
for the power FET for that supply. The power
control circuits also monitor load current and latch
off that slot if the load current exceeds a
programmed maximum value. In addition, once
the 12-V, the 5-V, and the 3.3-V FET are fully
enhanced, the load voltage is monitored. If the
load voltage drops out of specification limit after
these FETs are fully enhanced, the slot latches off.
This feature provides another level of protection
from load fault.
The auxiliary power control circuit provides power
to the 3VAUXx pins through the 3.3-V main supply
when it is above 3.0 V, and through the 3.3-V
standby input supply when the 3.3-V main supply
drops below 3.0 V.
The TPS2341 contains power FETs for 12 V at
500 mA, −12 V at 100 mA, and auxiliary 3.3 V at
375 mA for each slot. These power FETs are
short-circuit protected, slew rate controlled, and
over-temperature protected.
The serial interface communicates with a slot
controller using the I2C serial protocol. The
interface communicates with the slot, and
mechanical switches with individual, dedicated
lines. The interface operates from the 3.3-V
auxiliary power, but inputs are 5-V tolerant.
Mechanical switch inputs have internal pull-up
and hysteresis. The serial interface controls slot
power, and monitors board, power fault, and
switch input status.
Copyright  2003, Texas Instruments Incorporated
www.ti.com
1
SLUS513A − MAY 2003 − REVISED JULY 2004
absolute maximum ratings over operating free-air temperature (unless otherwise noted)†
Input voltage range:
P12VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 15 V
M12VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −15.0 V to 0.5 V
All others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 6 V
Output voltage range:
P12VO, 5V3VG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VP12VIN +0.5 V
P12VG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 28 V
M12VO, M12VG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VM12VIN−0.5 V to 0.5 V
Output current pulse: P12VO (DC internally limited) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 A
M12VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8 A
Operating virtual temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 125°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE: All voltages are respect to DGND.
electrical characteristics over recommended operating temperature range, P12VINA = P12VINB =
12 V, V5IN = 5 V, V3IN = 3.3 V, DIGVCC = 3.3 V, M12VINA = M12VINB = −12 V, 3VSTBYIN = 3.3 V, all
outputs unloaded, −40°C to 85°C, TA = TJ (unless otherwise noted)
5-V/3.3-V Supply
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
35
42
49
mV
34
42
49
mV
41
52
60
mV
ROCSET = 6.04 kΩ
37
52
62
mV
After P12VG and 5V3VG good
4.3
4.65
4.86
V
75
100
ns
5VOC input threshold voltage
5VOC Input threshold voltage
ROCSET = 6.04 kΩ,
3VOC Input threshold voltage
3VOC input threshold voltage
ROCSET = 6.04 kΩ,
5VISA, 5VISB voltage fault threshold
TA = TJ = 25°C
ROCSET = 6.04 kΩ
TA = TJ = 25°C
5VISA, 5VISB voltage fault minimum captured pulse
5VSA, 5VSB input bias current
PWRENx = high
−100
5VISA, 5VISB input bias current
PWRENx = high
5VISA, 5VISB bleed current
PWRENx = low,
3VISA, 3VISB voltage fault threshold
After P12VG and 5V3VG good
250
5VISx = 5 V
PWRENx = high
3VISA, 3VISB input bias current
PWRENx = high
3VISA, 3VISB bleed current
10
20
2.70
2.86
3.05
V
75
100
ns
PWRENx = low,
−100
3VISx = 3.3 V
P12VIN = 12V
5V3VGA, 5V3VGB turn-off time
C5V3VG = 0.022 µF,
5V3VG falling from 90% to 10%
www.ti.com
µA
A
5
10
20
mA
20
25
µA
200
5V3VGA, 5V3VGB good threshold
mA
14
5V3VGA, 5V3VGB discharge current
2
100
250
5V3VGA, 5V3VGB charge current
A
µA
5
3VISA, 3VISB voltage fault minimum captured pulse
time
3VSA, 3VSB input bias current
100
UNIT
9.5
11
1
mA
11.5
V
µs
SLUS513A − MAY 2003 − REVISED JULY 2004
electrical characteristics over recommended operating temperature range, P12VINA = P12VINB =
12 V, V5IN = 5 V, V3IN = 3.3 V, DIGVCC = 3.3 V, M12VINA = M12VINB = −12 V, 3VSTBYIN = 3.3 V, all
outputs unloaded, −40°C to 85°C, TA = TJ (unless otherwise noted) (continued)
+12-V Supply / −12-V Supply
PARAMETER
+12-V Internal N-channel MOSFET on-resistance
−12-V Internal N-channel MOSFET on-resistance
TEST CONDITIONS
PWREN = HIGH,
TA = TJ = 25°C
ID = 0.5 A
PWREN = HIGH,
ID = 0.5 A
ID = 0.1 A
PWREN = HIGH,
TA = TJ = 25°C
PWREN = HIGH,
+12-V overcurrent threshold
−12-V overcurrent threshold
P12VOA, P12VOB fault threshold voltage
ROCSET = 6.04 kΩ,
ID = 0.1 A
TA = TJ = 25°C
ROCSET = 6.04 kΩ
ROCSET = 6.04 kΩ,
TA = TJ = 25°C
MIN
0.3
Ω
0.4
Ω
Ω
0.9
0.79
0.94
1.09
A
0.73
0.94
1.12
A
0.20
0.24
0.28
A
0.18
0.24
0.30
A
After P12VG and 5V3VG good
9.50
10.30
11.15
V
75
100
ns
−20
−13
−23
M12VGA, M12VGB gate discharge current
200
Derived from charge pump
µA
mA
14
µA
2
9
17.5
19.0
20.5
PWREN = HIGH to M12VO = −10.4 V,
CM12VG = 0.022 µF,
RL = 120 Ω
CM12VO = 50 µF
15
20
PWREN = HIGH to P12VO = 11.4 V,
C12PVG = 0.022 µF,
RL = 24 Ω
CP12VO = 200 µF
30
75
PWREN = LOW to P12VO = 0.6 V,
CP12VG = 0.022 µF
1.5
3.5
µs
PWREN = LOW to M12VO = −0.6 V,
CM12VG = 0.022 µF
1.5
3.5
µs
P12VGA, P12VGB, discharge current
100
P12VGA, P12VGB good threshold
Turn-off time
0.18
0.75
UNIT
ROCSET = 6.04 kΩ
M12VGA, M12VGB gate charge current
Turn-on time
MAX
0.5
P12VOA, P12VOB voltage fault minimum captured
pulse time
P12VGA, P12VGB, charge current
TYP
mA
V
ms
M12VOA, M12VOB bleed current
−20
P12VOA, P12VOB bleed current
10
mA
noise filter
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Ignored spike from overcurrent
250
ns
Latched spike from overcurrent
500
ns
www.ti.com
3
SLUS513A − MAY 2003 − REVISED JULY 2004
electrical characteristics over recommended operating temperature range, P12VINA = P12VINB =
12 V, V5IN = 5 V, V3IN = 3.3 V, DIGVCC = 3.3 V, M12VINA = M12VINB = −12 V, 3VSTBYIN = 3.3 V, all
outputs unloaded, −40°C to 85°C, TA = TJ (unless otherwise noted) (continued)
input/output control
PARAMETER
TEST CONDITIONS
MIN
P12VIN = 12 V
TYP
P12VINA, P12VINB supply current
PWRENx = LOW,
V5IN supply current
V5IN = 5 V
V3IN supply current
V3IN = 3.3 V
M12VINA, M12VINB supply current
PWRENx = LOW,
3VSTBYIN supply current
3VSTBYIN = 3.3 V
200
DIGVCC supply current
DIGVCC = 3.3 V
200
MAX
UNIT
2
mA
1
1000
M12VIN −12 V
250
Overcurrent fault response time
V3IN start-up threshold voltage
µA
A
500
960
2.6
2.8
3.05
2.35
2.55
2.80
4.1
4.4
4.65
V5IN stop threshold voltage
3.75
4.00
4.35
P12VIN start-up threshold voltage
10.1
10.8
11.3
9.5
10.0
11.0
MIN
TYP
MAX
0.7
1.0
1.3
0.6
1.0
1.4
0.3
1.0
2.0
1.15
1.5
1.85
1.0
1.5
2.0
V3IN stop threshold voltage
V5IN start-up threshold voltage
P12VIN stop threshold voltage
ns
V
3.3 VAUX
PARAMETER
TEST CONDITIONS
Load applied for > 1 ms,
V3IN slow overcurrent shutdown
TA = TJ = 25°C
Load applied for > 1 ms
V3IN slow overcurrent fault response time
V3IN fast overcurrent shutdown
Load applied for < 100 µs,
TA = TJ = 25°C
Load applied for < 100 µs
UNIT
A
ms
A
5
10
35
µs
3VSTBYIN overcurrent shutdown
20
40
60
mA
3VSTBYIN overcurrent fault response time
10
25
50
µs
V3IN fast overcurrent fault response time
V3IN to 3VAUXA, 3VAUXB main switch on-resistance
I3VAUXx = −500 mA
300
425
mΩ
3VSTBYIN to 3VAUXA, 3VAUXB standby switch
on-resistance
I3VAUXx = −10 mA
10
20
Ω
2.5
2.9
V
3VSTBYIN undervoltage lockout
2.0
V3IN to 3VAUXA, 3VAUXB turn-on slew rate
5
3VSTBYIN to 3VAUXA, 3VAUXB turn-on slew rate
3VAUXA, 3VAUXB turn-on time from SWA/SWB
from SWx < 0.8 V,
C3VAUXx = 150 µF
3VAUXA, 3VAUXB turn-off time from SWA/SWB
from SWx > 2 V
3
10
V3IN to 3VSTBYIN crossover time
100
3VSTBYIN to V3IN crossover threshold
ms
2.5
3VSTBYIN to V3IN crossover time
2.8
3VSTBYIN to V3IN crossover hysteresis
3VAUXA, 3VAUXB bleed current
V/ms
0.1
3VAUXx = 3 V
2.9
µss
3.0
V
50
mV
150
µA
ac switching characteristics
PARAMETER
fMAX operating clock frequency
Recommended input rise and fall times
4
TEST CONDITIONS
0 ≤ TA ≤ 70°C
10% to 90% of DIGVCC
www.ti.com
MIN
TYP
MAX
UNIT
0
100
400
kHz
0.2
1
ns
SLUS513A − MAY 2003 − REVISED JULY 2004
electrical characteristics over recommended operating temperature range, P12VINA = P12VINB =
12 V, V5IN = 5 V, V3IN = 3.3 V, DIGVCC = 3.3 V, M12VINA = M12VINB = −12 V, 3VSTBYIN = 3.3 V, all
outputs unloaded, −40°C to 85°C, TA = TJ (unless otherwise noted) (continued)
dc electrical characteristics
MIN
TYP
MAX
Input threshold voltage (SDA, SCL)
PARAMETER
TEST CONDITIONS
0.8
1.4
2.0
High-level input threshold voltage
(SWA, SWB, PGOOD)
1.9
2.4
2.8
Low-level input threshold voltage
(SWA, SWB, PGOOD)
0.4
0.8
1.2
Input hysteresis (SWA, SWB, PGOOD)
1.0
1.6
2.0
Address and enable threshold voltage
(ADDR1, ENA, ENB)
0.4
1.0
1.5
UNIT
V
Address and enable hysteresis voltage
(ADDR1, ENA, ENB)
200
mV
Address and enable floating voltage when not
externally driven (ADDR1, ENA, ENB)
1.65
V
50
kΩ
Address and enable Thevenin equivalent
impedance (ADDR1, ENA, ENB)
Test mode threshold voltage (ADDR1)
1.75
Test mode hysteresis voltage (ADDR1)
2.50
2.80
200
High-level output voltage
(all digital outputs, except IRQ# and SDA)
IL = −4 mA
Low-level output voltage (all digital outputs)
IL = 4 mA
3.3 V pull-up resistance (SWA, SWB, PGOOD)
DIGVCC
− 0.4
V
mV
DIGVCC
− 0.2
V
0.2
0.4
30
200
kΩ
MIN
MAX
UNIT
Input voltage, P12VINA, P12VINB
10.8
13.2
Input voltage, V5IN
4.75
5.25
3.1
3.5
−13.2
−10.8
recommended operating conditions
Input voltage, DIGVCC
Input voltage, M12VINA, M12VINB
Input voltage, 3VSTBYIN
3.1
3.5
Load current, P12VOA, P12VOB
0
500
Load current, M12VOA, M12VOB
0
100
Load current, 3VAUXA, 3VAUXB
0
375
www.ti.com
V
mA
5
SLUS513A − MAY 2003 − REVISED JULY 2004
Terminal Functions
TERMINAL
NAME
NO.
I/O
DESCRIPTION
3VAUXA
36
O
3VAUXB
35
O
3VISA
30
I
3VISB
7
I
3VSA
31
I
3VSB
6
I
Connect to the source side of the 3.3-V FET switch. This pin in conjunction with the 3VIS pin senses
the current to the 3.3-V load by sensing the voltage drop across a sense resistor. A 0.01-µF bypass
capacitor to AGND is recommended.
3VSTBYIN
37
P
3.3Vaux standby voltage supply input. A 0.1-µF bypass capacitor to PWRGND2 is recommended.
5V3VGA
33
O
5V3VGB
5
O
Gate drive for the 5-V and 3.3-V FET switches. Ramp rate is programmed by external capacitance
connected to this pin. The capacitor is charged with a 20-µA current source and discharged with a
switch to PWRGND. The output UV circuitry is disabled until the voltage on this pin is greater than
11 V and the voltage on P12VGx is greater than 20 V.
5VISA
29
I
5VISB
8
I
5VSA
28
I
5VSB
9
I
ADDR1
17
I
AGND
11
G
Ground pin for the internal analog section.
AUX_GOODA
27
O
AUX_GOODB
19
O
Output power good indicator for the 3.3-VAUXx ouptut. This pin is driven to DIGVCC when the internal
N-channel MOSFET connected between V3IN and 3VAUXA (or 3VAUXB for slot B) is fully enhanced.
DIGVCC
24
P
Power pin for the digital section, connect to 3VSTBYIN. A 0.1-µF bypass capacitor from DIGVCC to
DIGGND is recommended.
DGND
23
G
Ground pin for the internal digital section.
ENA
15
I
ENB
16
I
IRQ#
18
O
Interrupt output. Open drain pulls low upon any fault detection or if SWA or SWB changes state.
M12VGA
41
O
A capacitor connected from this pin to M12VOA programs the ramp rate of the −12-V switched output.
The capacitor is charged with a 20-µA current source and discharged with a switch to PWRGND.
M12VGB
48
O
A capacitor connected from this pin to M12VOB programs the ramp rate of the −12-V switched output.
The capacitor is charged with a 20-µA current source and discharged with a switch to PWRGND.
M12VIN
2
P
M12VIN
39
P
M12VINA
40
P
M12VINB
1
P
M12VOA
38
O
M12VOB
3
O
OCSET
6
10
I
3.3Vaux voltage supply outputs. A 0.010.01-µF
F bypass capacitor to PWRGND2 is recommended.
Connect to the load side of the sense resistor. See definition for 3VS. This pin has a switched FET to
PWRGND to discharge any output load capacitance when the output is turned off. A 0.01-µF bypass
capacitor to AGND is recommended.
Connect to the load side of the sense resistor. See definition for 5VS. 5VIS is also used to sense the
output voltage for the 5-V UV circuit. This pin has a switched FET to PWRGND to discharge any output load capacitance when the output is turned off. A 0.01-µF bypass capacitor to AGND is recommended.
Connect to the source of the 5-V FET switch. This pin in conjunction with the 5VIS pin senses the
current to the 5-V load by sensing the voltage drop across the sense resistor. A 0.01-µF bypass capacitor to AGND is recommended.
Hard-wired I2C address pin. This pin represents the least significant bit (LSB) of a device’s I2C address. Tie to DGND for a logic 0 or allow to float for a logic 1. Tie ADDR1 to DIGVCC for test mode
fault mask.
Hardware enable pins. Use these pins to enable the device without I2C communication. Pull ENA high
to enable slot A. Pull ENB high to enable slot B. Pull ENA low to disable slot A hardware control and
revert to I2C control. Transitioning ENA from high to low also clears the slot A main fault latch. Pull
ENB low to disable slot B hardware control and revert to I2C control. Transitioning ENB from high to
low also clears the slot B main fault latch.
−12-V input voltage to the device. M12VIN, M12VINA and M12VINB must be tied together and are
internally connected by a high-resistance path. The heat conduction pad on the back of the package is
also connected to M12VIN. A 0.1-µF bypass capacitor from M12VIN to PWRGND is recommended.
−12-V input voltage to the device and the −12-V power FET. M12VINA, and M12VINB and M12VIN
must be tied together and are internally connected by a high-resistance path. The heat conducting pad
on the back of the package is also connected to M12VIN. A 0.1-µF bypass capacitor from M12VIN to
PWRGND is recommended.
−12-V Switched output. This pin has a switched FET to PWRGND to discharge any output load capacitance when the output is turned off. A 0.01-µF bypass capacitor to PWRGND is recommended.
A resistor connected between this pin and AGND sets the overcurrent threshold of the internal
switches. The +12-V and −12-V switches are set for the maximum permissible currents per the PCI
specification when a 1%, 6.04-kΩ resistor is used. A 0.1-µF bypass capacitor from OCSET to
ANAGND is recommended.
www.ti.com
SLUS513A − MAY 2003 − REVISED JULY 2004
Terminal Functions
TERMINAL
NAME
NO.
I/O
DESCRIPTION
P12VGA
42
O
Gate drive for the 12-V internal N-channel MOSFET for slot A. Connect a capacitor from this pin
to PWRGND1 to program the ramp rate. The capacitor is charged with a 5−µΑ current source
and discharged with a switch. The output undervoltage circuitry is disabled until the voltage on
this pin is greater than 20 V and the voltage on 5V3VGA is greater than 11 V.
P12VGB
47
O
Gate drive for the 12-V internal N-channel MOSFET for slot B. Connect a capacitor from this pin
to PWRGND2 to program the ramp rate. The capacitor is charged with a 5-µΑ current source
and discharged with a switch. The output undervoltage circuitry is disabled until the voltage on
this pin is greater than 20 V and the voltage on 5V3VGB is greater than 11 V.
P12VINA
44
P
12-V input to the device and the 12-V power FET for slot A. A 0.1-µF bypass capacitor from
P12VINA to PWRGND1 is recommended.
P12VINB
45
P
12-V input to the device and the 12-V power FET for slot B. A 0.1-µF bypass capacitor from
P12VINB to PWRGND2 is recommended.
P12VOA
43
O
12-V switched output for slot A. This pin has a switched FET to ground to discharge any output
load capacitance when the output is turned off. A 0.01-µF bypass capacitor to PWRGND1 is
recommended.
P12VOB
46
O
12-V switched output for slot B. This pin has a switched FET to ground to discharge any output
load capacitance when the output is turned off. A 0.01-µF bypass capacitor to PWRGND2 is
recommended.
PGOOD
20
I
Power good input. PGOOD has hysteresis so that it can be used as a power-on reset, driven
from a slow-rising RC. PGOOD also has a 100-kΩ pull-up to DIGVCC.
PGOOD_OUTA
22
O
PGOOD_OUTB
21
O
PWRGND1
4
G
PWRGND2
34
G
SCL
13
I
SDA
14
I/O
SWA
25
I
Slot A switch input. Low indicates the slot is populated. This input has hysteresis and a 100-kΩ
pull-up to DIGVCC, requiring only a capacitor to ground for debouncing mechanical noise.
SWB
12
I
Slot B switch input. Low indicates the slot is populated. This input has hysteresis and a 100-kΩ
pull-up to DIGVCC, requiring only a capacitor to ground for debouncing mechanical noise.
V3IN
32
P
3.3-V input to the device. A 0.1-µF bypass capacitor from V3IN to PWRGND is recommended.
V5IN
26
P
5-V input to the device. A 0.1-µF bypass capacitor from V5IN to PWRGND is recommended.
Output power good indicator for the main slot outputs. This pin is driven to DIGVCC when the
voltage on P12VGA (or P12VGB for slot B) is greater than 20 V and the voltage on 5V3VGA (or
5V3VGB for slot B) is greater than 11 V.
Ground pin for the power analog section.
Serial clock line for the I2C bus.
Serial data line for the I2C bus.
AVAILABLE OPTIONS
PACKAGE
TA
HTQFP (PHP)
−40°C to 85°C
TPS2341PHP
www.ti.com
7
SLUS513A − MAY 2003 − REVISED JULY 2004
M12VGB
P12VGB
P12VOB
P12VINB
P12VINA
P12VOA
P12VGA
M12VGA
M12VINA
M12VIN
M12VOA
3VSTBYIN
PHP PACKAGE
(TOP VIEW)
48 47 46 45 44 43 42 41 40 39 38 37
M12VINB
M12VIN
M12VOB
PWRGND1
5V3VGB
3VSB
3VISB
5VISB
5VSB
OCSET
AGND
SWB
1
36
2
35
3
34
4
33
5
32
6
31
7
30
8
29
9
28
10
27
11
26
12
25
3VAUXA
3VAUXB
PWRGND2
5V3VGA
V3IN
3VSA
3VISA
5VISA
5VSA
AUX_GOODA
V5IN
SWA
SCL
SDA
ENA
ENB
ADDR1
IRQ#
AUX_GOODB
PGOOD
PGOOD_OUTB
PGOOD_OUTA
DGND
DIGVCC
13 14 15 16 17 18 19 20 21 22 23 24
The heat-conduction pad on the underside of the package is electrically connected to M12VINA. Either connect
the heat-conducting pad to −12 VIN or leave unconnected. Do not connect the heat-conducting pad to any other
power plane or to a ground.
8
www.ti.com
SLUS513A − MAY 2003 − REVISED JULY 2004
FUNCTIONAL BLOCK DIAGRAM
V3IN
32
3VSTBYIN 37
36 3VAUXA
OVERCURRENT SENSE
TO
SECOND
SLOT
FROM
GOOD
INPUTS
AUX FAULT
LATCH
S Q
R
+
2.9 V
5 µA
Q
SR
CONTROL
2.5 ms
TURN−OFF
DELAY
SWA 25
27 AUX_GOODA
5 µA
THERMAL
SHUTDOWN
+
20 V
42
P12VGA
44
P12VINA
OC SENSE
20 µA
43
P12VOA
+
5V3VGA 33
11 V
3VSA 31
+
MAIN
FAULT
LATCH
3VISA 30
5VSA 28
38
M12VOA
41
M12VGA
OC
SENSE
S
Q
R
Q
20 µA
+
5VISA 29
P12VO
5VIS
3VIS
P12VINA
V5IN
3VIN
OUTPUTS
GOOD
40 M12VINA
INPUTS
GOOD
22 PGOOD_OUTA
ENA 15
TWO ITERATIONS
ONE ITERATION
PGOOD 20
18
100 µA
IRQ#
TO
SECOND
SLOT
OCSET 10
CURRENT LIMIT
THRESHOLD
PWRENA AUXFLTA FLTA IMASKA PWRENB AUXFLTB
FLTB
IMASKB
SDA 14
SERIAL TO PARALLEL CONVERTER
SCL 13
11
4
34
26
17
24
23
AGND
PWRGND1
PWRGND2
V5IN
ADDR1
DIGVCC
DGND
www.ti.com
2
39
M12VIN M12VIN
UDG−01152
9
SLUS513A − MAY 2003 − REVISED JULY 2004
TYPICAL CHARACTERISTICS
Refer to the typical application diagram (Figure 13) for circuit component values for Figures 1 through 9.
MAIN SWITCH RAMPUP VOLTAGE
vs
TIME
3.5
15
+12 V
3.3-V MAIN SWITCH UNDERVOLTAGE
FAULT RESPONSE
vs
TIME
3VIN
3.0
+5 V
+3.3 V
5
0
−5
V3VOUT − Output Voltage − V
VLOAD − Output Voltage − V
10
2.5
2.0
1.5
3VOUT
1.0
PGOOD_OUTA
0.5
−10
0
−12 V
−0.5
−15
T − Time − 1 ms / div
T − Time − 10 ms / div
Figure 2.
Figure 1.
12-V OUTPUT AND INRUSH CURRENT
vs
TIME
+12 V Gate
0.20
+12 V Inrush Current
15
0.15
+12 V Output
10
0.10
5
PGOOD_OUTA
0
0.05
V5VOUT − Output Votlage − V
+5 V Output
I12LOAD − Inrush Current − A
V12VOUT − Output Voltage − V
20
12
6
0.25
CLOAD = 300 µF
5
10
4
8
3
6
PGOOD_OUTA
2
4
1
2
0
5V Load
Current
−1
−2
0
−2
+5 V Output
−5
10
0
−0.05
−3
−6
T − Time − 10 ms / div
T − Time − 10 µs / div
Figure 3.
Figure 4.
www.ti.com
−4
I5VOUT − Load Currentt − A
25
5-V OUTPUT OVERLOAD RESPONSE
vs
TIME
SLUS513A − MAY 2003 − REVISED JULY 2004
TYPICAL CHARACTERISTICS
Refer to the typical application diagram (Figure 13) for circuit component values for Figures 1 through 9.
−12-V SHORTED LOAD STARTUP VOLTAGE
AND LOAD CURRENT
vs
TIME
3VAUX OUTPUT RAMP-UP VOLTAGE
AND INRUSH CURRENT
vs
TIME
0.30
3.5
1.4
0
0.25
3.0
1.2
−2
0.20
2
0.15
−12 V Load
Current
−6
0.10
0.05
−8
−10
0
−12
−0.05
3VAUXA
Output
2.5
SWA
Input
2.0
AUX_GOODA
1.5
−14
−0.10
0.8
0.6
3VAUXA
Inrush Current
1.0
0.5
0.4
0.2
0
−12 V Gate Voltage
1.0
I3VAUXALOAD − Load Current − A
−4
IM12LOAD − Load Current − A
V3VAUXA − Output Voltage − V
VM12VOUT − Output Voltage − V
−12 V Output
0
CLOAD = 150 µF
−0.5
T − Time − 1 ms / div
−0.2
T − Time − 500 µs / div
Figure 5.
Figure 6.
3VSTBYIN TO V3IN OUTPUT VOLTAGE
V3IN TO 3VSTBYIN OUTPUT VOLTAGE
CROSSOVER RESPONSE
vs
TIME
CROSSOVER RESPONSE
vs
TIME
4.0
4.0
3.5
3.0
3.0
V3VAUXA − Output Voltage − V
V3VAUXA − Output Voltage − V
3VAUXA Output
3.5
2.5
2.0
1.5
1.0
0.5
3VAUXA Output
2.5
2.0
1.5
1.0
0.5
AUX_GOODA
AUX_GOODA
0
0
−0.5
−0.5
T − Time − 5 µs / div
T − Time − 10 µs / div
Figure 7.
Figure 8.
www.ti.com
11
SLUS513A − MAY 2003 − REVISED JULY 2004
TYPICAL CHARACTERISTICS
Refer to the typical application diagram (Figure 13) for circuit component values for Figures 1 through 9.
3VAUX OUTPUT OVERLOAD RESPONSE
vs
TIME
3.5
3VAUXA Output
1.2
AUX_GOODA
2.5
1.0
2.0
0.8
1.5
1.0
0.6
3VAUXA
Load Current
0.5
0.4
0.2
0
I3VAUXALOAD − Load Current
−A
V3VAUXA − Voltage Amplitude − V
3.0
1.4
0
−0.5
−0.2
T − Time − 10 ms / div
Figure 9.
12
www.ti.com
SLUS513A − MAY 2003 − REVISED JULY 2004
APPLICATION INFORMATION
The functional block diagram shows the TPS2341 with detailed information on the analog functions. For clarity,
the analog circuits for only one slot are shown in detail.
+12-V Supply Control
The TPS2341 integrates an N-channel power MOSFET for the +12-V supply between pins P12VINA and
P12VOA. The switch has a nominal on resistance of 180 mΩ and shuts down the slot upon detecting an
overcurrent condition. The in-rush current of the supply is controlled in an open-loop fashion by charging an
external capacitor tied directly to the internal N-channel MOSFET gate with a constant current source. This
results in a linear voltage ramp on the gate and also on the P12VOA output due to the source follower connection
of the switch.
The switch turns on when the logic declares the input supplies are valid, slot is healthy and the enable from the
I2C serial interface is active. The P12VOA output voltage is monitored for an undervoltage fault once the +12-V,
+5-V and +3.3-V switches are fully enhanced. The switch shuts off upon a disable command from the I2C serial
interface or a fault on the slot. An internal resistor connects between the P12VOA and PWRGND1 upon disable
and bleeds off any residual charge on the output.
Slot B functions independently and in the same manner as slot A with the input supply connected to P12VINB
and the load connected to P12VOB.
−12-V Supply Control
The TPS2341 integrates an N-channel power MOSFET for the −12-V supply between pins M12VINA and
M12VOA. The switch has a nominal on resistance of 500 mΩ and shuts down the slot upon detecting an
overcurrent condition. The in-rush current of the supply is controlled in a closed-loop fashion by charging an
external Miller capacitor tied between the N-channel MOSFET gate and drain with a constant current source.
This results in a linear voltage ramp on the drain (M12VOA) pin.
The switch turns on when the logic declares the input supplies are valid, slot is healthy and the enable from the
I2C serial interface is active. The M12VOA output voltage is not monitored for an undervoltage fault. The switch
shuts off upon a disable command from the I2C serial interface or a fault on the slot. An internal resistor connects
between the M12VOA and PWRGND1 upon disable and bleeds off any residual charge on the output.
Slot B functions independently and in the same manner as slot A with the input supply connected to M12VINB
and the load connected to M12VOB.
www.ti.com
13
SLUS513A − MAY 2003 − REVISED JULY 2004
APPLICATION INFORMATION
+5-V and +3.3-V Supply Controls
The TPS2341 provides the control circuitry for external N-channel power MOSFETs on the +5-V and +3.3-V
supplies. The switches share a common gate capacitor for slew rate control and have independent overcurrent
detection circuitry. A source side sense resistor provides a differential sense voltage to pins 5VSA and 5VISA
that is compared to a threshold voltage for the +5-V supply overcurrent fault. The +3.3-V supply operates
similarly and a fault on either supply shuts down the slot. The in-rush current of the supply is controlled in a
open-loop fashion by charging an external capacitor tied directly to the N-channel MOSFET gate with a constant
current source. This results in a linear voltage ramp on the gate and also on the load due to the source follower
connection of the switch.
The switch turns on when the logic declares the input supplies are valid, slot is healthy and the enable from the
I2C serial interface is active. The 3VISA and 5VISA pins are monitored for an undervoltage fault once the +12-V,
+5-V and +3.3-V switches are fully enhanced. The switch shuts off upon a disable command from the I2C serial
interface or a fault on the slot. An internal resistor connects between 3VISA and PWRGND1 and also between
5VISA and PWRGND1 upon disable and bleeds off any residual charge on the output.
Slot B functions independently and in the same manner as slot A.
3VAUX Supply Control
The TPS2341 integrates the power FETs for the 3.3 V auxiliary outputs providing power from V3IN when the
main supply is above 3 V and from the 3VSTBYIN supply when V3IN is below 3 V.
The 3VAUX circuit differs from the main circuits in regard to slew rate control. The main circuits slew rate is
programmable by an external capacitor while the 3VAUX slew rate is fixed. The 3VAUX outputs turn on and slew
up upon the application of 3VSTBYIN and SW. The slew rate is slow enough to allow charging a large bulk
capacitor (up to 150 µF) without tripping the overload comparator. After the main supply inputs are active, the
3VAUX switch connected to 3VSTBYIN shuts off and the switch connected to V3IN turns on in a rapid
break-before-make fashion.
Upon the undervoltage failure of the V3IN or one of the positive main supplies, the V3IN switch shuts off and
the 3VSTBYIN switch turns on in a rapid break-before-make fashion. A high on the SW input shuts off the active
switch.
The V3IN switch has slew rate control slow enough to allow charging the bulk capacitance in the event that
3VSTBYIN and the main supplies become active together.
The V3IN switches have two overcurrent thresholds. The slow overcurrent threshold trips when the load current
exceeds 1 A for longer than 1 ms. The 3VAUX outputs can accomodate a transient current due to a load device
enable or charge up to 150 µF of bulk capacitance without tripping a nuisance fault. The fast overcurrent
threshold trips when the load current exceeds 1.5 A for longer than 10 µs. This threshold captures a direct short
on the 3VAUX output.
The 3VSTBYIN switches detect an overcurrent condition when the load current exceeds 40 mA for 25 µs.
The main and standby faults are cleared by disabling the 3VAUX slot with the SW input or by removing the input
supply voltage.
14
www.ti.com
SLUS513A − MAY 2003 − REVISED JULY 2004
APPLICATION INFORMATION
Fault Logic
The main supply switches require the inputs to be healthy before turning on. The slot is shut down upon an
overload condition or output undervoltage condition and all switches shut off upon a device overtemperature
condition. The switch starts to turn on when the P12VINA, V5IN and V3IN supply inputs are above the
undervoltage thresholds, the PGOOD input is active and the PWRENA (or PWRENB for slot B) control output
from the I2C serial interface is active.
The P12VOA, P5VISA and P3VISA pins monitor the load for an undervoltage fault once the +12-V, +5-V and
+3.3-V switches are fully enhanced. The +12-V, +5-V, +3.3-V and −12-V load currents are monitored for an
overload condition continuously upon slot enable. The device overtemperature sensor is always active, cannot
be masked with the test mode fault mask, and shuts down all switches upon sensing excessive internal die
temperature.
The main load faults are latched and can be cleared by cycling the slot enable with the I2C serial interface (if
operating in serial mode), by transitioning slot enable from high to low (if operating in hardware enable mode),
or by dropping and then raising power to the TPS2341.
The 3.3VAux standby switch requires only the 3VSTBYIN supply to be healthy before turning on. An overload
condition shuts down the slot standby switch. The latched fault can be cleared by toggling the SWA (or SWB
for slot B) input or by cycling the standby supply voltage.
The 3.3VAux main switch requires the main supply voltages to be within specifications before turning on. The
slot 3.3VAux main switch shuts off upon an overload condition and all switches shut off upon the device over
temperature condition. The latched fault can be cleared by cycling the SWA (or SWB for slot B) 3.3VAux disable
pin or removal and assertion of input supply voltage.
The I2C serial interface can be used to determine the offending fault. Polling the STATUS READ register
determines which slot caused the fault and differentiates between the main supply switches or the 3.3VAux
switches. The slot STATUS register indicates an undervoltage fault, thermal shutdown, overload fault or
commanded disable occurred. The OVERLOAD register isolates an overload condition to the individual supply
switch.
Operation Without I2C
The TPS2341 can be used in a system without I2C, although some of the diagnostic capabilities of the TPS2341
are lost. Slot main power is applied by applying a rising edge to the PGOOD input and then applying a rising
edge to the appropriate slot enable input ENx. Slot main power status is observed at the PGOOD_OUTx output.
In the event of a loss of power on any main input, the TPS2341 resets to all slots off. Main slot power restarts
on the next rising edge of ENx after power is recovered.
In a system without I2C, the interrupt output IRQ# is not meaningful and should not be connected. SDA should
be pulled up to 3.3 V. SCL and ADDR1 should be grounded.
www.ti.com
15
SLUS513A − MAY 2003 − REVISED JULY 2004
APPLICATION INFORMATION
Interrupt Service Request
The TPS2341 generates an interrupt by asserting the IRQ# output. Any of the following conditions causes an
interrupt:
D
D
D
D
The SWx input changes state.
An auxiliary or main output over-current fault occurs.
A main input/output under-voltage condition occurs.
Thermal shutdown of the TPS2341 occurs.
The status registers (see Table 1) can be read to determine the cause of the interrupt and to identify the slot
causing the interrupt.
Slot level control of an interrupt is possible through the interrupt mask in register 00h. For example, setting mask
bits zero and two to logic 1 and logic 0, respectively, enables a slot A interrupt but disables a slot B interrupt.
These mask bits only affect the IRQ# output pin, the internal IRQ bits in register 10h still acknowledge the fault.
Resetting the Interrupt
A SWx input state change causes an interrupt that is cleared by setting bit 4 (SW interrupt reset) of register 00h
to logic 1. This bit must then be set to logic 0 to rearm the interrupt.
An interrupt that is caused by an overload on the auxiliary channel will be cleared along with the fault when the
SWx input pin is brought high (disable) or the PGOOD input pin is brought low.
An interrupt that is caused by an overload on the main channel or a main input/output undervoltage condition
will be cleared along with the fault when the ENx input pin is brought low and the ENx bit in register 00h is brought
low. This interrupt is also cleared when the PGOOD input is brought low.
I2C Operation
The TPS2341 communicates with the master controller using the I2C serial protocol. The SCL pin, which is the
clock, and the SDA pin, which is the bi-directional data, are used for transferring data to and from the device.
The TPS2341 implements a 7-bit addressing scheme with the upper six bits internally defined 010000 and the
least significant bit user programmable with the ADDR1 pin.
The data protocol recognizes a START pulse as a high-to-low transition on the SDA pin when the SCL pin is
high. The rising edge of the SCL pin clocks a logic-high into (or out of) the device when SDA is high and a
logic-low when the SDA pin is low. An ACKNOWLEDGE handshake occurs as the device receiving the 8-bit
word pulls the SDA pin low when the SCL pin is clocked the ninth time. Another 8-bit word followed by an
ACKNOWLEDGE bit can immediately begin depending upon the read or write cycle protocol.
The write cycle protocol begins with a START bit, contains three 8-bit words, each followed by an
ACKNOWLEDGE bit and ends with a STOP bit. The first 8-bit word is the device address which must match
the internally defined upper 6 bits and externally defined least significant bit with a low LSB (A0) to indicate a
write cycle. Following a good device address word, the second 8-bit word selects the internal register that the
control device would like to place data into. The third 8-bit word is the actual data to be placed into the selected
registers.
16
www.ti.com
SLUS513A − MAY 2003 − REVISED JULY 2004
SCL
Stop Bit
Clock ’1’
Clock ’0’
Clock ’1’
Clock ’1’
Start Bit
SDA
R/W Bit
Write Cycle
Register Address
Data from
Master to
TPS2341
Stop Bit
Device Address
R/W=0
D7 D6 D5 D4 D3 D2 D1 D0
Ack Bit
R7 R6 R5 R4 R3 R2 R1 R0
Ack Bit
Start Bit
A7 A6 A5 A4 A3 A2 A1 A0
Ack Bit
SDA
R/W Bit
R/W Bit
Read Cycle
Device Address
R/W=1
Data from
TPS2341 to
Master
Ack Bit
Stop Bit
Register Address
D7 D6 D5 D4 D3 D2 D1 D0
Ack Bit
A7 A6 A5 A4 A3 A2 A1 A0
Start Bit
Device Address
R/W=0
R7 R6 R5 R4 R3 R2 R1 R0
Ack Bit
Start Bit
A7 A6 A5 A4 A3 A2 A1 A0
Ack Bit
SDA
UDG−02155
Figure 10. I2C Signal Timing
www.ti.com
17
SLUS513A − MAY 2003 − REVISED JULY 2004
APPLICATION INFORMATION
I2C Operation (continued)
The read cycle protocol begins with a START bit, followed by two 8-bit words, another START bit, another two
8-bit words and ends with a STOP bit. The first two 8-bit words are similar to the write cycle, with a low LSB for
the device address, and instruct the device which internal register will be polled. A START bit after the second
word interrupts the write cycle after the internal register is defined. The next 8-bit word following the second
START bit is once again the device address, however, the LSB (A0) is now high indicating the device is expected
to return the data from the selected internal register. After the ACKNOWLEDGE bit, the TPS2341 drives the
SDA line and return the 8-bits of data from the internal register.
Table 1. Register DefinitionS
REGISTER
00h
10h
18
ASSIGNMENT
BIT
Control Write
READ/
WRITE
W
DEFINITION
0
Slot A Int_Mask
1: Allow Slot A interrupts to set IRQ# active
0: Mask Slot A interrupts on IRQ#
1
Slot A Enable
1: Enable Slot A main switches
0: Disable Slot A main switches
2
Slot B Int_Mask
1: Allow Slot B interrupts to set IRQ# active
0: Mask Slot B interrupts on IRQ#
3
Slot B Enable
1: Enable Slot B main switches
0: Disable Slot B main switches
4
SW Interrupt Reset
1: Reset interrupt request from SWA or SWB edge transition
0: Clear reset
5
Spare a; data stored here is visible on read 11h, bit 5
6
Spare b; data stored here is visible on read 11h, bit 6
7
Spare c; data stored here is visible on read 11h, bit 7
Status Read
R
0
Slot A PGood
1: Slot A main switches active and healthy
0: Slot A main switches not healthy
1
Slot A Aux_Good
1: Slot A 3.3-V Aux main active and healthy
0: Slot A 3.3-V Aux not healthy
2
Slot A IRQ
1: Slot A interrupt request active
0: Slot A interrupt request inactive
3
Slot B PGood
1: Slot B main switches active and healthy
0: Slot B main switches not healthy
4
Slot B Aux_Good
1: Slot B 3.3-V Aux main active and healthy
0: Slot B 3.3-V Aux not healthy
5
Slot B IRQ
1: Slot B interrupt request active
0: Slot B interrupt request inactive
6
PGOOD_INPUT
1: PGOOD input pin is high
0: PGOOD input pin is low
7
0
www.ti.com
SLUS513A − MAY 2003 − REVISED JULY 2004
APPLICATION INFORMATION
Table 1. Register Definitions (continued)
11h
12h
Control Read
R
0
Slot A Int_Mask
1: Slot A allows interrupts to set IRQ# active
0: Slot A masks interrupts on IRQ#
1
Slot A Enable
1: Slot A main switches enable active
0: Slot A main switches enable inactive
2
Slot B Int_Mask
1: Slot B allows interrupts to set IRQ# active
0: Slot B masks interrupts on IRQ#
3
Slot B Enable
1: Slot B main switches enable active
0: Slot B main switches enable inactive
4
SW Interrupt Reset
1: Reset Interrupt request from SWA or SWB edge transition
0: Clear reset
5
Spare a; Data stored from write 00h, bit 5
6
Spare b; Data stored from write 00h, bit 6
7
Spare c; Data stored from write 00h, bit 7
Slot A Status
R
0
Slot A enable
1: Slot A main switches enable active
0: Slot A main switches enable inactive
1
Input undervoltage fault
1: Input undervoltage fault active
0: Input undervoltage fault inactive
2
Slot A output undervoltage fault
1: Slot A output undervoltage fault active
0: Slot A output undervoltage fault inactive
3
Slot A overload fault
1: Slot A overload fault active
0: Slot A overload fault inactive
4
Thermal shutdown fault
1: Thermal shutdown fault active
0: Thermal shutdown fault inactive
5
SWA input
1: SWA input active; after rising edge delay
0: SWA input inactive; no falling edge delay
6
Slot A PGOOD
1: Slot A main switches active and healthy
0: Slot A main switches not healthy
7
Slot A Main Fault
1: Slot A main fault active
0: Slot A main fault inactive
www.ti.com
19
SLUS513A − MAY 2003 − REVISED JULY 2004
APPLICATION INFORMATION
Table 1. Register Definitions (continued)
REGISTER
13h
14h
20
ASSIGNMENT
BIT
Slot A Overload
READ/
WRITE
R
DEFINITION
0
Slot A +3V Overload
1: Slot A +3.3-V overload active
0: Slot A +3.3-V overload inactive
1
Slot A +5V Overload
1: Slot A +5-V overload active
0: Slot A +5-V overload inactive
2
Slot A +12-V Overload
1: Slot A +12-V overload active
0: Slot A +12-V overload inactive
3
Slot A −12-V Overload
1: Slot A −12-V overload active
0: Slot A −12-V overload inactive
4
Slot A 3VSTBYIN Overload
1: Slot A 3.3-VAux standby overload active
0: Slot A 3.3-VAux standby overload inactive
5
Slot A 3VMAIN overload
1: Slot A 3.3-VAux main overload active
0: Slot A 3.3-VAux main overload inactive
6
Slot A 3VAUX standby switch on
1: Slot A 3.3-VAux standby switch active
0: Slot A 3.3-Vaux standby switch inactive
7
Slot A 3VAUX main switch on
1: Slot A 3.3VAux main switch active
0: Slot A 3.3VAux main switch inactive
Slot B Status
R
0
Slot B enable
1: Slot B main switches enable active
0: Slot B main switches enable inactive
1
Input undervoltage fault
1: Input undervoltage fault active
0: Input undervoltage fault inactive
2
Slot B output undervoltage fault
1: Slot B output undervoltage fault active
0: Slot B output undervoltage fault inactive
3
Slot B overload fault
1: Slot B overload fault active
0: Slot B overload fault inactive
4
Thermal shutdown fault
1: Thermal shutdown fault active
0: Thermal shutdown fault inactive
5
SWA input
1: SWA input active; after rising edge delay
0: SWA input inactive; no falling edge delay
6
Slot B PGOOD
1: Slot B main switches active and healthy
0: Slot B main switches not healthy
7
Slot B Main Fault
1: Slot B main fault active
0: Slot B main fault inactive
www.ti.com
SLUS513A − MAY 2003 − REVISED JULY 2004
APPLICATION INFORMATION
Table 1. Register Definitions (continued)
15h
Slot B Overload
R
0
Slot B +3V Overload
1: Slot B +3.3-V overload active
0: Slot B +3.3-V overload inactive
1
Slot B +5V Overload
1: Slot B +5-V overload active
0: Slot B +5-V overload inactive
2
Slot B +12-V Overload
1: Slot B +12-V overload active
0: Slot B +12-V overload inactive
3
Slot B −12-V Overload
1: Slot B −12-V overload active
0: Slot B −12-V overload inactive
4
Slot B 3VSTBYIN Overload
1: Slot B 3.3-VAux standby overload active
0: Slot B 3.3-VAux standby overload inactive
5
Slot B 3VMAIN overload
1: Slot B 3.3-VAux main overload active
0: Slot B 3.3-VAux main overload inactive
6
Slot B 3VAUX standby switch on
1: Slot B 3.3-VAux standby switch active
0: Slot B 3.3-Vaux standby switch inactive
7
Slot B 3VAUX main switch on
1: Slot B 3.3VAux main switch active
0: Slot B 3.3VAux main switch inactive
www.ti.com
21
SLUS513A − MAY 2003 − REVISED JULY 2004
APPLICATION INFORMATION
Test Mode Functions for Address Bit
The TPS2341 address pin (ADDR1) provides two functions. The input provides the I2C serial interface with a
unique address when two TPS2341 devices share the same address bank and also provides a means of
disabling faults. Three different voltage levels are used to define the status of the input signal. Upon pulling the
address pin low, the serial interface address bit is set low. The serial interface address bit is set high if the
address pin is allowed to float or is driven to one-half the voltage at DIGVCC. Upon pulling ADDR1 to DIGVCC
the internal test mode is invoked which masks the overload and undervoltage faults and does not shut down
the slots when the thresholds are exceeded. This is intended to be used for board development only to avoid
nuisance faults from improperly sized bulk capacitance or excessive switching loads. Caution must be taken
to never exceed the maximum dissipation or absolute maximum conditions of the device while the device
self-protection is disabled.
Table 2. I2C Device Address Decode
BIT
DEFINITION
A0
R/W bit
0: Write data from master to TPS2341
1: Read data from TPS2341 to master
A1
Device address bit 1 (LSB) compared with pin ADDR1
A2
0 internally defined
A3
0 internally defined
A4
0 internally defined
A5
0 internally defined
A6
1 internally defined
A7
0 internally defined
Table 3. Test Mode Functions for Adddress Bits
22
BIT
VOLTAGE
LEVEL (V)
ADDRESS
FUNCTION
TEST MODE
FUNCTION
< 0.8
Low
OFF
0.8 < VA1 < 2.5
High
A1
OFF
> 2.5
High
Mask fault active
www.ti.com
SLUS513A − MAY 2003 − REVISED JULY 2004
APPLICATION INFORMATION
Layout Considerations
It is important to use good layout practices regarding device placement and etch routing of the
backplane/system board to optimize the performance of the hot plug circuit. Some of the key considerations
are listed here:
D Decoupling capacitors should be located close to the device.
D Any protection devices (e.g. zener clamps) should be located close to the device.
D To reduce insertion loss across the hot plug interface, use wide traces for the supply and return current
paths. A power plane can be used for the supply return or PWRGND nodes.
D Additional copper placed at the land patterns of the sense resistors and pass FETs can significantly reduce
the thermal impedance of these devices, reducing temperature rise in the module and improving overall
reliability.
D Because typical values for current sense resistors can be very low (6 mΩ typical), board trace resistance
between elements in the supply current paths becomes significant. To achieve maximum accuracy of the
overload thresholds, good Kelvin connections to the resistors should be used for the current sense inputs
to the device. The current sense traces should connect symmetrically to the sense resistor land pattern,
in close proximity to the element leads, not upstream or downstream from the device.
D For best noise immunity, provide separate ground planes for the analog, digital, and power circuitry. These
ground planes should tie together at a single point in the system.
LOAD CURRENT PATH
LOAD CURRENT PATH
3VSA
3VISA
3VSA
3VISA
SENSE
RESISTOR
TPS2341
TPS2341
UDG−02154
Figure 11. Connecting the Sense Resistors
These recommended layouts provide force-and-sense (Kelvin) connection to the current sense resistor to
minimize circuit board trace resistance.
www.ti.com
23
SLUS513A − MAY 2003 − REVISED JULY 2004
APPLICATION INFORMATION
Thermal Model
The TPS2341 is packaged in the HTQFP-48 PowerPadt quad flat-pack package. The PowerPad package is
a thermally enhanced standard size device package designed to eliminate the use of bulky heatsinks and slugs
traditionally used in thermal packages. This package can be easily mounted using standard printed circuit board
(PCB) assembly techniques, and can be removed and replaced using standard repair procedures.
The PowerPad package is designed so that the leadframe die pad is exposed on the bottom of the device. This
provides an extremely low thermal resistance between the die and the thermal pad. The thermal pad can be
soldered directly to the PCB for heatsinking. In addition, through the use of thermal vias, the thermal pad can
be directly connected to a power/ground plane or special heat sink structure designed into the PCB. On the
TPS2341, the die substrate is internally connected to the −12 V input supply. and therefore the power plane or
heatsink connected to the thermal pad on the bottom of the device must also connect to the −12 V input supply
(recommended) or float independent of any supply (acceptable).
The thermal performance can be modeled by determining the thermal resistance between the die and the
ambient environment. Thermal resistances are measures of how effectively an object dissipates heat. Typically,
the larger the device, the more surface area available for power dissipation and the lower the object’s thermal
resistance. Figure 12 illustrates the thermal path and resistances from the die, TJ through the printed circuit
board to the ambient air.
Die
PD
(Watts)
Die Junction Temperature
TJ
θJC
Copper
Trace
Die Case Temperature
ÉÉ ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÉÉÉÉÉÉÉ
ÎÎÎ
ÉÉÉ
ÎÎÎ ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎ
ÏÏ ÎÎÎÎ
ÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÏÏ
ÎÎ
ÎÎÎÎ
ÎÎ ÎÎÎÎ ÎÎÎÎ
ÎÎ ÎÎÎÎ
ÎÎ ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
TPS2341 48HTQFP PowerPADt
Via
Thermal Via
θCP
Solder
PCB Pad Temperature
TP
θPH
PCB Heatsink Temperature
TH
θHA
Heatsink/Copper Plane
Ambient Air Temperature
−12 VIN or Floating
TC
TA
UDG−02156
Figure 12. PowerPADt Thermal Model
Technical Brief PowerPADt Thermally Enhanced Package (SLMA002) can be used as a guide to model the
TPS2341 thermal resistance. The following example assumes the conditions as described in the technical brief.
The TPS2341, mounted to a copper pad with solder on a PCB and two ounce traces, should exhibit a thermal
resistance from junction temperature to ambient temperature of 29_C/W.
24
www.ti.com
SLUS513A − MAY 2003 − REVISED JULY 2004
APPLICATION INFORMATION
Table 4. TPS2341 Continuous Maximum Load Power Consumption (All Drivers On)
SUPPLY DRIVER
+12 V @ 0.5 A
−12 V @ 100 mA
+3VAux @ 375 mA
RDS(on)
(Ω)
POWER PER SLOT
(W)
TOTAL POWER
(W)
0.5
0.1
0.2
0.9
0.01
0.02
0.425
0.06
0.12
+12 V @ 3 mA
0.04
0.08
+5 V @1 mA
0.005
+3 V @ 0.5 mA
0.002
−12 V @ 0.25 mA
0.003
0.006
3VSTBY @ 0.2 mA
0.001
DIGVCC @ 0.2 mA
0.001
Total Power Consumption
0.435
T RISE + P TOTAL
q JA + (0.435 W)
ǒ29 deg CńWǓ
(1)
= 12.7 _C
T J + T A ) T RISE + 50 C ) 12.7
O
(2)
= 62.7_C
This example indicates that with the ambient air at 50°C the TPS2341 junction temperature rises to 63°C which
is below the absolute maximum junction temperature of 85°C and ensures the device operates properly and
within design specifications. The transient power consumption must also be considered for the conditions during
initial ramp-up of the output supplies, however, this varies significantly depending upon output load impedance
for each application and each supply.
Refer to Technical Briefs PowerPADtThermally Enhanced Package (TI Literature No. SLMA003) and
PowerPADt Made Easy (TI Literature No. SLMA004) for more information.
www.ti.com
25
SLUS513A − MAY 2003 − REVISED JULY 2004
APPLICATION INFORMATION
C14 0.01 µF
C12 0.01 µF
+5 V
Q1
IRF7413
C7
0.1 µF
C15
0.01 µF
C13
0.01 µF
RS1
6 mΩ
+5 V OUTB
Q2
IRF7413
+3.3 V
RS2
6 mΩ
+3.3 V OUTB
C20 0.1 µF
C10
0.1 µF
C9
0.1 µF
C8
0.1 µF
ROC
6.04 kΩ
+12 V OUTB
C23
0.01 µF
C1
0.056 µF
+3.3V AUXOUT B
−12 V
C23
0.01 µF
+12 V
SWB
−12V OUT B
GND
SCL
13
SCL
2
1
C22
0.01 µF
M12VINB
3
M12VIN
4
M12VOB
5
PWRGND1
3VSB
6
5V3VGB
7
3VISB
8
5VISB
AGND
9
5VSB
10
OCSET
11
SWB
12
M12VGB
48
14
SDA
P12VGB
47
15
ENA
P12VOB
46
16
ENB
P12VINB
45
17
ADDR1
P12VINA
44
18
IRQ#
P12VOA
43
19
AUX_GOODB
P12VGA
42
C4
0.027 µF
C3
0.015 µF
SDA
RIRQ#
3.3 kΩ
TPS2341
48HTQFP
PowerPADt
IRQ#
AUX_GOODB
20
PGOOD
M12VGA
41
21
PGOOD_OUTB
M12VINA
40
22
PGOOD_OUTA
M12VIN
39
23
DGND
M12VOA
38
24
DIGVCC
3VSTBYIN
37
C6 0.015 µF
+12V OUT A
C5
0.027 µF
PGOOD
C26
0.01 µF
PGOOD_OUTB
PGOOD_OUTA
SWA
V5IN
AUX_GOODA
5VSA
5VISAn
3VISA
3VSA
V3IN
5V3VGA
PWRGND2
3VAUXB
8VAUXA
−12V OUT A
25
26
27
28
29
30
31
32
33
34
35
36
C25
0.01 µF
3VSTBYIN
+3.3V AUXOUT A
C24
0.01 µF
SWA
AUX_GOODA
Q3 IRF7413
RS3 6 mΩ
Q4 IRF7413
+5V OUT A
RS4 6 mΩ
+3.3 V OUT A
C11
0.1 µF
C17
0.01 µF
C16
0.01 µF
C2
0.056 µF
C18
0.01 µF
C19
0.01 µF
UDG−02152
Figure 13. Typical Applications Diagram
26
www.ti.com
SLUS513A − MAY 2003 − REVISED JULY 2004
Determining Component Values
Load Conditions
Table 5. Load Conditions for Determining Component Values
SUPPLY DRIVER
ILOAD
(A)
ITRAP
(A)
CLOAD
(µF)
SR
(V/s)
+12 V
0.5
0.94
300
250
(1)
+5 V
5
7.0
3000
200
+3.3 V
7.6
10.0
3000
200
−12 V
0.1
0.19
150
200
+3.3 Vaux
+3.3 Vaux(1)
0.375
1.0
150
5000
0.02
0.04
150
100
+3.3Vaux turn-on from stand-by power.
+3.3-V Supply
Overload Trip Point
Desired ITRIP (nom) ≅ 10 A
R SENSE +
V RTRIP (nom)
I TRIP (nom)
I TRIP(min) +
I TRIP(max) +
+ 52 mV + 0.0052 W NChoose 5 mW, 2% sense resistor
10 A
V TRIP (min)
R SENSE (max)
V TRIP (max)
R SENSE (min)
+ 44 mV + 8.63 A
5.1 mW
+ 60 mV + 12.2 A
4.9 mW
(3)
(4)
(5)
Gate Capacitance
IINRUSH ≤ 8.6 A
ICLOAD = IINRUSH − ILOAD = 8.6 A − 7.6 A = 1 A
from i = C dV/dt for the load capacitance and charge current: ∆T = ∆V (C/i)
mF
ǒ3000
Ǔ + 9.9 ms
1A
+ 3.3 V
(6)
from i = C dV/dt for the gate capacitance and charge current: C = i × ( ∆T/∆V)
ǒ
Ǔ
+ 25 mA 9.9 ms using the maximum gate capacitance and charge current
3.3 V
(7)
= 0.075 µF ∴ choose 0.1 µF, 10% capacitor.
The nominal load turn-on time is calculated in equation (8).
DT + DV (Cńi) + 3.3 V
mF
ǒ0.1
Ǔ + 16.5 ms
20 mA
SR + 3.3 V + 200 Vńs
16.5 ms
(8)
(9)
www.ti.com
27
SLUS513A − MAY 2003 − REVISED JULY 2004
APPLICATION INFORMATION
+5-V Supply
Overload Trip Point
Desired ITRIP (nom) ≅ 7 A
R SENSE +
V RTRIP (nom)
I TRIP(min) +
I TRIP(max) +
I TRIP (nom)
+ 42 mV + 0.006 W NChoose 6 mW, 2% sense resistor.
7A
V TRIP (min)
R SENSE (max)
V TRIP (max)
R SENSE (min)
+ 35 mV + 5.72 A
6.12 mW
+ 48 mV + 8.16 A
5.88 mW
(10)
(11)
(12)
Gate Capacitance
IINRUSH ≤ 5.72 A
ICLOAD = IINRUSH − ILOAD = 5.72 A − 5 A = 720 mA
from the chosen gate capacitance (shared with the 3.3-V MOSFET).
I CLOAD + C
(DVńDT) + 3000 mF
ǒ200VńsǓ + 600 mA (max)
(13)
IINRUSH = ICLOAD + ILOAD = 600 mA + 5 A = 5.6 A
The nominal load turn on time is calculated in equation (14).
DT + DV (Cńi) + 5 V
28
mF
ǒ0.1
Ǔ + 25 ms
20 mA
(14)
www.ti.com
SLUS513A − MAY 2003 − REVISED JULY 2004
APPLICATION INFORMATION
+12-V Supply
Gate Capacitance
IINRUSH ≤ 0.79 A from a minimum +12-V overcurrent threshold voltage.
ICLOAD = IINRUSH − ILOAD = 0.79 A − 0.5 A = 290 mA
from i = C dV/dt for the load capacitance and charge current: ∆T = ∆V (C/i)
300 mF
ǒ290
Ǔ + 12.4 ms
mA
+ 12 V
(15)
from i = C dV/dt for the gate capacitance and charge current: C = i × ( ∆T/∆V)
ǒ
Ǔ
+ 14 mA 12.4 ms using the maximum gate capacitance and charge current
12 V
(16)
= 0.014 µF ∴ choose 0.02 µF, 10% capacitor.
The nominal load turn-on time is calculated in equation (17).
DT + DV (Cńi) + 12 V
mF
ǒ0.02
Ǔ + 48 ms
5 mA
SR + 12 V + 250 Vńs
48 ms
(17)
(18)
−12-V Supply
Gate Capacitance
IINRUSH ≤ 150 mA from minimum −12-V overcurrent threshold voltage.
ICLOAD = IINRUSH − ILOAD = 150 mA − 100 mA = 50 mA
from i = C dV/dt for the load capacitance and charge current: ∆T = ∆V (C/i)
mF
ǒ150
Ǔ + 36 ms
50 mA
+ 12 V
(19)
from i = C dV/dt for the gate capacitance and charge current: C = i × ( ∆T/∆V)
ǒ
Ǔ
+ 25 mA 36 ms using the maximum gate capacitance and charge current
12 V
(20)
= 0.075 µF ∴ choose 0.1 µF, 10% capacitor.
The nominal load turn-on time is calculated in equation (21).
DT + DV (Cńi) + 12 V
mF
ǒ0.1
Ǔ + 60 ms
20 mA
(21)
SR + 12 V + 200 Vńs
60 ms
(22)
www.ti.com
29
SLUS513A − MAY 2003 − REVISED JULY 2004
APPLICATION INFORMATION
+3.3-V Auxiliary Supply
Inrush Current
IINRUSH = C dV/dt + ILOAD for the load capacitance
+ 150 mF
V Ǔ ) 375 mA + 1125 mA
ǒ15ms
(23)
The nominal load turn-on time is calculated in equation (24).
T + DV + 3.3 V + 660 ms
dV
5V
1 ms
dt
ǒ Ǔ ǒ
Ǔ
(24)
Standby Inrush Current
IINRUSH = C dV/dt + ILOAD for the load capacitance
ǒ
Ǔ
+ 150 mF 0.1 V ) 20 mA + 35 mA
1 ms
(25)
The nominal load turn-on time is calculated in equation (26).
T + DV + 3.3 V + 33 ms
dV
0.1 V
1 ms
dt
ǒ Ǔ ǒ
Ǔ
(26)
Thermal Shutdown
Under normal operating consitions, the power dissipation in the TS2341 is low enough that the junction
temperature (TJ) is not more than 15°C above air temperature (TA). However, in the case of a load that exceeds
PCI specifications (but remains under the TPS2341 overcurrent threshold) power dissipation can be higher. To
prevent any damage from an out-of-specification load or severe rise in ambient temperature, the TPS2341
contains two independent thermal shutdown circuits, one for each main supply slot.
The highest power dissipation in the TPS2341 is from the 12-V power FET so that TPS2341 temperature sense
elements are integrated closely with these FETs. These sensors indicate when the temperature at these
transistors exceeds approximately 150°C, due either to average device power dissipation, 12-V power FET
power dissipation, or a combination of both.
When excessive junction temperature is detected in one slot, that slot’s fault latch is set and remains set until
the junction temperature drops by approximately 10°C and the slot is then restarted through the serial interface
or supply dropping. The other slot is not affected by this event.
Digital Circuits
The I2C serial interface is available once DIGVCC is stable. However, data in the main power registers is
accurate only if the main supply voltages are within specification. Data in the AUXFAULTx register is accurate
only if the 3VSTBYIN supply voltage is within specifications.
30
www.ti.com
PACKAGE OPTION ADDENDUM
www.ti.com
4-Mar-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TPS2341PHP
ACTIVE
HTQFP
PHP
48
250
None
CU NIPDAU
Level-3-220C-168 HR
TPS2341PHPR
ACTIVE
HTQFP
PHP
48
1000
None
CU NIPDAU
Level-3-220C-168 HR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional
product content details.
None: Not yet available Lead (Pb-Free).
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens,
including bromine (Br) or antimony (Sb) above 0.1% of total product weight.
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated