TI TS12A12511DGKR

TS12A12511
SCDS248B – OCTOBER 2009 – REVISED APRIL 2011
www.ti.com
±6 V/+12 V, 5 Ω, LOW rON SINGLE SPDT ANALOG SWITCH
Check for Samples: TS12A12511
FEATURES
1
•
•
•
•
•
•
•
•
•
•
±2.7 V to ±6 V Dual Supply
2.7 V to 12 V Single Supply
5-Ω (typ) ON-State Resistance
1.6-Ω (typ) ON-State Resistance Flatness
3.3-V, 5-V Compatible Digital Control Inputs
Rail-to-Rail Analog Signal Handling
Fast tON, tOFF Times
Tiny 8-Lead SOT-23, 8-Lead MSOP, and QFN-8
Packages
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
ESD Performance Tested per JESD 22
– 2000-V Human-Body Model
(A114-B, Class II)
– 1000-V Charged-Device Model (C101)
DGK PACKAGE
(TOP VIEW)
COM
NC
GND
V+
Automatic Test Equipment
Power Routing
Communication Systems
Data Acquisition Systems
Sample-and-Hold Systems
Relay Replacement
Battery-Powered Systems
8
2
7
6
3
NO
V–
IN
N.C.
5
4
DCN PACKAGE
(TOP VIEW)
COM
NC
GND
V+
1
8
2
7
3
6
5
4
NO
V–
IN
N.C.
DRJ PACKAGE
(TOP VIEW)
APPLICATIONS
•
•
•
•
•
•
•
1
COM
1
8
NO
NC
2
7
V–
GND
3
6
IN
V+
4
5
N.C.
N.C. – Not internally connected
NC – Normally closed
NO – Normally open
The Exposed Thermal Pad must be
electrically connected to V– or left floating.
DESCRIPTION/ORDERING INFORMATION
The TS12A12511 is a single-pole double-throw (SPDT) analog switch capable of passing signals with swings of
0 to 12 V or –6 V to 6 V. This switch conducts equally well in both directions when it is on. It also offers a low
ON-state resistance of 5 Ω (typical), which is matched to within 1 Ω between channels. The max current
consumption is <1 μA and –3 dB bandwidth is >93 MHz. The TS12A12511 exhibits break-before-make switching
action, preventing momentary shorting when switching channels. This device is available packaged in an 8-lead
MSOP, 8-lead SOT-23, and a 8-pin QFN.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
UNLESS OTHERWISE NOTED this document contains
PRODUCTION DATA information current as of publication date.
Products conform to specifications per the terms of Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2009–2011, Texas Instruments Incorporated
TS12A12511
SCDS248B – OCTOBER 2009 – REVISED APRIL 2011
www.ti.com
Table 1. ORDERING INFORMATION
PACKAGE (1)
TA
–40°C to 85°C
(1)
(2)
(2)
ORDERABLE PART NUMBER
TOP-SIDE MARKING
MSOP – DGK
Tape and reel
TS12A12511DGKR
2US
QFN – DRJ
Tape and reel
TS12A12511DRJR
ZVE
SOT – DCN
Tape and reel
TS12A12511DCNR
NFH
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
TRUTH TABLE
IN
NC TO COM, COM TO NC
NO TO COM, COM TO NO
L
On
Off
H
Off
On
ABSOLUTE MAXIMUM RATINGS (1)
TA = 25°C (unless otherwise noted).
MIN
V+ to V–
MAX
UNIT
13
V
V+ to GND
–0.3
13
V
V– to GND
–6.5
0.3
V
V– – 0.5
V + + 0.5
VI/O
Analog inputs
IIN
Digital inputs
II/O
V
±30
mA
Peak current
NC, NO, or COM
±100
mA
Continuous current
NC, NO, or COM
±50
mA
Tstg
Storage temperature range
–65
150
°C
TA
Operating temperature range
–40
85
°C
(1)
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating
conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
THERMAL IMPEDANCE RATINGS
UNIT
θJA
2
Package thermal impedance
DCN package
220
DGK package
173
DRJ package
103
°C/W
Copyright © 2009–2011, Texas Instruments Incorporated
TS12A12511
SCDS248B – OCTOBER 2009 – REVISED APRIL 2011
www.ti.com
ELECTRICAL CHARACTERISTICS
±5-V Dual Supply
V+ = 5 V ± 10%, V- = -5 V ± 10%, TA = –40°C to 85°C (unless otherwise noted)
PARAMETER
SYMBOL
TEST CONDITIONS
TA= –40°C to 85°C
TA= 25°C
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
Analog Switch
Analog signal range
V–
VNC = -4.5 V to +4.5 V
or VNO = –4.5 V to 4.5 V, ICOM = –10 mA;
see Figure 12
5
5
V+
V
8
Ω
ON-state resistance
rON
ON-state resistance
match between
channels
ΔrON
VNC = -4.5 V to +4.5 V
or VNO = -4.5 V to +4.5 V,
ICOM = –10 mA
1
1.2
1.6
Ω
ON-state resistance
flatness
rON(flat)
VNC = -3.3 V to +3.3 V
or VNO = -3.3 V to +3.3 V,
ICOM = –10 mA
1.6
2.2
2.2
Ω
Leakage Currents
OFF leakage current
INC(OFF),
INO(OFF)
VNC = -4.5 V to +4.5 V
or VNO = -4.5 V to +4.5V
VCOM = -4.5 V to +4.5 V; see Figure 13
±0.5
±1
±50
nA
ON leakage current
INC(ON),
INO(ON)
VNC = -4.5 V to +4.5 V
or VNO = -4.5 V to +4.5 V
VCOM = open; see Figure 14
±0.5
±1
±50
nA
Digital Inputs
High-level input
voltage
VINH
2.4
V+
V
Low-level input
voltage
VINL
0
0.8
V
±1
μA
Input current
IINL, IINH
Control input
capacitance
CIN
VIN = VINL or VINH
0.005
2.5
pF
Dynamic (1)
Turn-ON time
tON
RL = 300 Ω, CL = 35 pF,
VCOM = 3.3 V; see Figure 16
80
95
115
ns
Turn-OFF time
tOFF
RL = 300 Ω, CL = 35 pF,
VCOM = 3.3 V
41
50
56
ns
Break-before-make
time delay
tBBM
RL = 300 Ω, CL = 35 pF,
VNC = VNO = 3.3 V; see Figure 17
36
Charge injection
QC
VNC = VNO = 0 V, RGEN = 0 Ω, CL = 1 nF;
see Figure 18
26
pC
18
ns
OFF isolation
OISO
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
see Figure 19
–70
dB
Channel-to-channel
crosstalk
XTALK
RL = 50 Ω, CL = 5 pF, f = 1 MHz,
see Figure 20
–70
dB
93
MHz
Bandwidth –3 dB
Total harmonic
distortion
BW
RL = 50 Ω, CL = 5 pF; see Figure 21
THD
RL = 600 Ω, CL = 15pF, VNO = 1VRMS,
f = 20 kHz; see Figure 22
0.004
%
NC, NO
OFF capacitance
CNC(OFF),
CNO(OFF)
f = 1 MHz; see Figure 15
14
pF
COM, NC, NO
ON capacitance
CCOM(ON),
CNC(ON),
CNO(ON)
f = 1 MHz; see Figure 15
60
pF
Supply
Positive supply current
(1)
I+
0.03
1
μA
Ensured by design, not subject to production test.
Copyright © 2009–2011, Texas Instruments Incorporated
3
TS12A12511
SCDS248B – OCTOBER 2009 – REVISED APRIL 2011
www.ti.com
ELECTRICAL CHARACTERISTICS
12-V Single Supply
V+ = 12 V ± 10%, V– = 0 V, GND = 0 V, TA = –40°C to 85°C (unless otherwise noted)
PARAMETER
TA= –40°C to 85°C
TA= 25°C
SYMBOL
TEST CONDITIONS
ON-state resistance
ron
VNC =0 V to 10.8 V or VNO = 0 V to
10.8 V,
ICOM = –10 mA, see Figure 12
ON-state resistance
match between
channels
Δron
VNC = 0 V to 10.8 V or VNO = 0 V to
10.8 V,
ICOM = –10 mA
1.6
ON-state resistance
flatness
ron(flat)
VNC = 3.3 V to 7V or VNO = 3.3 V to
7 V,
ICOM = –10 mA
1.7
OFF leakage current
INC(OFF),
INO(OFF)
VNC = 0 V to 10.8 V or VNO = 0 V to
10.8 V,
VCOM = 0 V to 10.8 V; see
Figure 13
±0.5
ON leakage current
INC(ON),
INO(ON)
VNC = 0 V to 10.8V or VNO = 0 V to
10.8 V,
VCOM = open; see Figure 14
±0.5
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
Analog Switch
Analog signal range
0
V+
V
8
Ω
2.6
Ω
3.2
Ω
±10
±50
nA
±10
±50
nA
V
5
5
2.4
1.8
Leakage Currents
Digital Inputs
High-level input voltage
VINH
5
V+
Low-level input voltage
VINL
0
0.8
V
±0.1
μA
Input current
Digital input capacitance
4
IINL, IINH
CIN
VIN = VINL or VINH
±0.005
2.7
pF
Copyright © 2009–2011, Texas Instruments Incorporated
TS12A12511
SCDS248B – OCTOBER 2009 – REVISED APRIL 2011
www.ti.com
ELECTRICAL CHARACTERISTICS
12-V Single Supply (continued)
V+ = 12 V ± 10%, V– = 0 V, GND = 0 V, TA = –40°C to 85°C (unless otherwise noted)
PARAMETER
SYMBOL
TEST CONDITIONS
TA= –40°C to 85°C
TA= 25°C
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
Dynamic (1)
Turn-ON time
tON
RL = 300 Ω, CL = 35 pF,
VCOM = 3.3 V; see Figure 16
56
85
110
ns
Turn-OFF time
tOFF
RL = 300 Ω, CL = 35 pF,
VCOM = 3.3 V; see Figure 16
25
30
31
ns
Break-before-make
time delay
tBBM
RL = 300 Ω, CL = 35 pF,
VNC = VNO = 3.3 V; see Figure 17
30
Charge injection
QC
RGEN = VNC = VNO = 0 V, RGEN = 0
Ω, CL = 1 nF;
see Figure 18
491
pC
19
ns
OFF isolation
OISO
RL = 50 Ω, CL = 5 pF, f = 1 MHz,
see Figure 19
–70
dB
Channel-to-channel
crosstalk
XTALK
RL = 50 Ω, CL = 5 pF, f = 1 MHz,
see Figure 20
–70
dB
Bandwidth –3 dB
BW
RL = 50 Ω, CL = 5 pF, see
Figure 21
122
MHz
Total harmonic distortion
THD
RL = 600 Ω, CL = 15pF, VNO =
1VRMS, f = 20 kHz; see Figure 22
0.04
%
NC, NO
OFF capacitance
CNC(OFF),
CINO(OFF)
f = 1 MHz, see Figure 15
14
pF
COM, NC, NO
ON capacitance
CCOM(ON),
CNC(ON),
CNO(ON)
f = 1 MHz, see Figure 15
55
pF
Supply
Positive supply current
(1)
I+
0.07
1
μA
Ensured by design, not subject to production test.
Copyright © 2009–2011, Texas Instruments Incorporated
5
TS12A12511
SCDS248B – OCTOBER 2009 – REVISED APRIL 2011
www.ti.com
ELECTRICAL CHARACTERISTICS
5-V Single Supply
V+ = 5 V ± 10%, V– = 0 V, GND = 0 V, TA = –40°C to 85°C (unless otherwise noted)
PARAMETER
SYMBOL
TEST CONDITIONS
TA= –40°C to 85°C
TA= 25°C
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
Analog Switch
Analog signal range
0
ON-state resistance
ron
VNC =0 V to 4.5 V or VNO = 0 V to
4.5 V,
ICOM = –10 mA;
see Figure 12
ON-state resistance
match between
channels
Δron
VNC =0 V to 4.5 V or VNO = 0 V to
4.5 V,
ICOM = –10 mA
1
ON-state resistance
flatness
ron(flat)
VNC =0 V to 4.5 V or VNO = 0 V to
4.5 V,
ICOM = –10 mA
1.3
8
V+
V
10
12.5
Ω
1.1
1.5
Ω
2
Ω
1.3
Leakage Currents
OFF leakage current
INC(OFF),
INO(OFF)
VNC =0 V to 4.5 V or VNO = 0 V to
4.5 V,
VCOM = 0 V to 4.5 V; see Figure 13
±0.5
±1
±50
nA
ON leakage current
INC(ON),
INO(ON)
VNC = 0 V to 4.5V or VNO = 0 V to
4.5 V,
VCOM = open; see Figure 14
±0.5
±1
±50
nA
V
Digital Inputs
High-level input voltage
VINH
2.4
V+
Low-level input voltage
VINL
0
0.8
V
±0.1
μA
Input current
Digital input capacitance
6
IINL, IINH
CIN
VIN = VINL or VINH
0.01
2.8
pF
Copyright © 2009–2011, Texas Instruments Incorporated
TS12A12511
SCDS248B – OCTOBER 2009 – REVISED APRIL 2011
www.ti.com
ELECTRICAL CHARACTERISTICS
5-V Single Supply (continued)
V+ = 5 V ± 10%, V– = 0 V, GND = 0 V, TA = –40°C to 85°C (unless otherwise noted)
PARAMETER
SYMBOL
TEST CONDITIONS
TA= –40°C to 85°C
TA= 25°C
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
Dynamic (1)
Turn-ON time
tON
RL = 300 Ω, CL = 35 pF,
VCOM = 3.3 V; see Figure 16
119
145
178
ns
Turn-OFF time
tOFF
RL = 300 Ω, CL = 35 pF,
VCOM = 3.3 V; see Figure 16
38
47
95.2
ns
Break-before-make
time delay
tBBM
RL = 300 Ω, CL = 35 pF,
VNC = VNO = 3.3 V; see Figure 17
79
Charge injection
QC
VGEN = VNC = VNO = 0 V, RGEN = 0
Ω, CL = 1 nF;
see Figure 18
65
pC
44
ns
OFF isolation
OISO
RL = 50 Ω, CL = 5 pF, f = 1 MHz,
see Figure 19
–70
dB
Channel-to-channel
crosstalk
XTALK
RL = 50 Ω, CL = 5 pF, f = 1 MHz,
see Figure 20
–70
dB
BW
RL = 50 Ω, see Figure 21
152
MHz
THD
RL = 600 Ω, CL = 15 pF, VNO = 1
VRMS, f = 20 kHz; see Figure 22
0.04
%
Bandwidth –3 dB
Total harmonic distortion
NC, NO
OFF capacitance
CNC(OFF),
CNO(OFF)
f = 1 MHz, see Figure 15
15
pF
COM, NC, NO
ON capacitance
CCOM(ON),
CNC(ON),
INO(ON)
f = 1 MHz, see Figure 15
55
pF
Power Requirements
V+ supply current
(1)
I+
VIN = 0 V or V+
0.02
1
μA
Ensured by design, not subject to production test.
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
Pin Function Descriptions
TERMINAL
NAME
NO.
1
COM
DESCRIPTION
Common terminal. Can be an input or output.
2
NC
3
GND
Normally closed. Can be an input or output.
4
V+
5
N.C.
6
IN
Logic control input
7
V–
Most negative power supply. This pin is only used in dual-supply applications and should be tied to ground in
single-supply applications.
8
NO
Normally open. Can be an input or output.
Ground (0 V) reference
Most positive power supply
No connect. Not internally connected.
Copyright © 2009–2011, Texas Instruments Incorporated
7
TS12A12511
SCDS248B – OCTOBER 2009 – REVISED APRIL 2011
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS
0.10
7.0
0.05
6.0
0.00
ON-leakage Current (nA)
rON (Ohms)
5.0
4.0
3.0
2.0
V+=3V, V-=-3.0V
V+=5V, V-=-5V
V+=6V,V-=-6V
1.0
-0.05
-0.10
-0.15
-0.20
-0.25
25C/3V
-0.30
25C/5V
25C/6V
-0.35
-0.40
-6.0
0.0
-6
-5
-4
-3
-2
-1
0
1
2
3
4
5
6
-4.0
-2.0
0.0
2.0
4.0
VIO(V)
Switch I/O Voltage (V)
Figure 1. rON vs VIO
Figure 2. Leakage Current vs I/O voltage (Switch ON)
0.05
6.0
3.00
0.00
2.50
-0.10
Positive Supply Current (nA)
OFF-leakage Current (nA)
-0.05
-0.15
-0.20
25C/3V
-0.25
25C/5V
25C/6V
-0.30
-0.35
-6.0
-4.0
-2.0
0.0
2.0
4.0
6.0
2.00
V+=3V, V-=-3V
V+=5V, V-=-5V
V+=6V, V-=-6V
1.50
1.00
0.50
Switch I/O Voltage (V)
0.00
-40.00
25.00
85.00
Temperature (degrees C)
Figure 3. Leakage Current vs I/O Voltage (Switch OFF)
Figure 4. Positive Supply Current vs Temperature
0.00
7.0
-40.00
25.00
85.00
6.0
-0.50
-1.00
-1.50
4.0
VOUT (V)
Negative Supply Current (nA)
5.0
V+=3V, V-=-3V
V+=5V, V-=-5V
V+=6V, V-=-6V
3.0
2.0
V+=3V,V-=-3V
V+=5V,V-=-5V
V+=6V,V-=-6V
-2.00
1.0
0.0
-2.50
-1.0
0.0
-3.00
Temperature (Degrees C)
Figure 5. Negative Supply Current vs Temperature
8
0.5
1.0
1.5
2.0
2.5
3.0
3.5
Control Input Voltage (V)
Figure 6. Control Input (IN) Threshold Voltage
Copyright © 2009–2011, Texas Instruments Incorporated
TS12A12511
SCDS248B – OCTOBER 2009 – REVISED APRIL 2011
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
-5.00
0.0
-2.0
-15.00
-4.0
-25.00
Magnitude (dB)
Magnitude (dB)
-6.0
-8.0
-10.0
-35.00
-45.00
-12.0
-55.00
-14.0
-16.0
-65.00
-18.0
1.00E+6
10.00E+6
100.00E+6
-75.00
1.00E+6
1.00E+9
Frequency (Hz)
10.00E+6
100.00E+6
1.00E+9
Frequency (Hz)
Figure 7. Bandwidth Dual Supply (±5V)
Figure 8. Off Isolation vs Frequency Dual Supply (±5v)
-5.0
0.050
0.045
-15.0
0.040
0.035
0.030
-35.0
THD
Magnitude (dB)
-25.0
12V_0V/NC-COM
12V_0V/NO-COM
5V_0V/NC-COM
5V_0V/NO-COM
5V_5V/NC-COM
5V_5V/NO-COM
0.025
-45.0
0.020
-55.0
0.015
0.010
-65.0
0.005
-75.0
1.00E+6
10.00E+6
100.00E+6
1.00E+9
Frequency (Hz)
Figure 9. Crosstalk vs Frequency Dual Supply (±5V)
Copyright © 2009–2011, Texas Instruments Incorporated
0.000
10
100
1000
10000
100000
Frequency
Figure 10. THD+N (%) vs Frequency
9
TS12A12511
SCDS248B – OCTOBER 2009 – REVISED APRIL 2011
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
600
500
400
Charge Injection (pC)
300
200
100
0
-100
-200
-300
-400
6V
5V
5.
5V
4V
4.
5V
3.
5V
3V
2V
2.
5V
1V
1.
5V
0.
5V
0V
-1
V
-0
.5
V
-2
V
-1
.5
V
-3
V
-2
.5
V
5V
-3
.
-4
V
-5
V
-4
.5
V
-6
V
-5
.5
V
-500
Bias Voltage
Figure 11. Charge Injection vs Bias Voltage
10
Copyright © 2009–2011, Texas Instruments Incorporated
TS12A12511
SCDS248B – OCTOBER 2009 – REVISED APRIL 2011
www.ti.com
TEST CIRCUITS
V+
VNO NO
COM
+
VCOM
Channel ON
r on
VI
ICOM
IN
VCOM – VNO
I COM
VI = V IH or V IL
+
GND
V–
Figure 12. ON-State Resistance
V+
VNO NO
COM
+
VCOM
+
VI
OFF-State Leakage Current
Channel OFF
VI = V IH or V IL
IN
+
GND
V–
Figure 13. OFF-State Leakage Current (ICOM(OFF), INC(OFF))
V+
VNO NO
COM
+
VI
VCOM
ON-State Leakage Current
Channel ON
VI = V IH or V IL
IN
+
GND
V–
Figure 14. ON-State Leakage Current (ICOM(ON), INC(ON))
Copyright © 2009–2011, Texas Instruments Incorporated
11
TS12A12511
SCDS248B – OCTOBER 2009 – REVISED APRIL 2011
www.ti.com
V+
VNO
NO
Capacitance
Meter
VBIAS = V +, V IO, or GND and
VI = V IO or GND
COM
COM
VI
IN
Capacitance is measured at NO,
COM, and IN inputs during ON
and OFF conditions.
VBIAS
GND
V–
Figure 15. Capacitance (CCOM(OFF), CCOM(ON), CNC(OFF), CNC(ON))
V+
NO
VCOM
VI
Logic
Input(1)
VNO
TEST
RL
CL
tON
50 Ω
35 pF
V+
tOFF
50 Ω
35 pF
V+
COM
CL(2)
IN
RL
VIO
Logic
Input
(VI)
GND
50%
50%
0
tON
V–
(1)
(2)
VCOM
Switch
Output
(VNO)
tOFF
90%
90%
All input pulses are supplied by generators having the following characteristics: PRR≤ 10 MHz, ZO = 50 Ω, tr < 5 ns, tf < 5 ns.
CL includes probe and jig capacitance.
Figure 16. Turn-ON (tON) and Turn-OFF Time (tOFF)
12
Copyright © 2009–2011, Texas Instruments Incorporated
TS12A12511
SCDS248B – OCTOBER 2009 – REVISED APRIL 2011
www.ti.com
V+
NC or NO
VIO
Logic
Input
(VI)
VNC or V NO
VCOM
50%
0
COM
NC or NO
CL(2)
Switch
Output
(VCOM)
RL
IN
VI
VNC or V NO = V +/2
RL = 50 Ω
CL = 35 pF
GND
V–
(2)
90%
tBBM
Logic
Input(1)
(1)
90%
All input pulses are supplied by generators having the following characteristics: PRR≤ 10 MHz, ZO = 50 Ω, tr < 5 ns, tf < 5 ns.
CL includes probe and jig capacitance.
Figure 17. Break-Before-Make Time Delay (tBBM)
V+
RGEN
VGEN
Logic
Input
(VI)
VIH
OFF
ON
OFF V
IL
NO
COM
+
VCOM
VCOM
∆VCOM
CL(1)
VI
VGEN = 0 to V+
IN
Logic
Input(2)
RGEN = 0
CL = 1 nF
QC = CL × ∆VCOM
VI = V IH or V IL
GND
V–
(1)
(2)
CL includes probe and jig capacitance.
All input pulses are supplied by generators having the following characteristics: PRR≤ 10 MHz, ZO = 50 Ω, tr < 5 ns, tf < 5 ns.
Figure 18. Charge Injection (QC)
V+
Network Analyzer
Channel OFF: NO to COM
50 W
VNO NO
VI = V IO or GND
COM
Source
Signal
VCOM
50 W
Network Analyzer Setup
VI
50 W
+
Source Power = 0 dBm
(632-mV P-P at 50-Wload)
IN
GND
DC Bias = 350 mV
V–
Figure 19. OFF Isolation (OISO)
Copyright © 2009–2011, Texas Instruments Incorporated
13
TS12A12511
SCDS248B – OCTOBER 2009 – REVISED APRIL 2011
www.ti.com
V+
Network Analyzer
50 W
VNO1
Source
Signal
VNO2
NO1
Channel ON: NO to COM
COM1
NO2
VI
50 W
Network Analyzer Setup
50 W
COM2
Source Power = 0 dBm
(632 mV P-P at 50 Wload)
IN
+
DC Bias = 350 mV
GND
V–
Figure 20. Channel-to-Channel Crosstalk (XTALK)
V+
Network Analyzer
50 W
VNO
NO
Channel ON: NO to COM
VCOM
COM
VI = V IH or V IL
Source
Signal
Network Analyzer Setup
VI
50 W
IN
Source Power = 0 dBm
(632-mV P-P at 50-Wload)
+
GND
DC Bias = 350 mV
V–
Figure 21. Bandwidth (BW)
Channel ON: COM to NO
VSOURCE = V + P-P
VI = (VIO – V+/2) or -V +/2
RL = 600 Ω
fSOURCE = 20 Hz to 20 kHz
CL = 50 pF
V+/2
Audio Analyzer
NO
Source
Signal
COM
CL(1)
600
VI
IN
600
-V +/2
(1)
V–
CL includes probe and jig capacitance.
Figure 22. Total Harmonic Distortion
14
Copyright © 2009–2011, Texas Instruments Incorporated
TS12A12511
SCDS248B – OCTOBER 2009 – REVISED APRIL 2011
www.ti.com
REVISION HISTORY
Changes from Revision A (May 2010) to Revision B
•
Page
Deleted preview status from DGK and DCN packages. ....................................................................................................... 1
Copyright © 2009–2011, Texas Instruments Incorporated
15
PACKAGE MATERIALS INFORMATION
www.ti.com
17-May-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
TS12A12511DCNR
SOT-23
DCN
8
3000
180.0
8.4
TS12A12511DGKR
MSOP
DGK
8
2500
330.0
12.4
5.3
TS12A12511DRJR
SON
DRJ
8
1000
180.0
12.4
4.25
Pack Materials-Page 1
3.23
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3.17
1.37
4.0
8.0
Q3
3.4
1.4
8.0
12.0
Q1
4.25
1.15
8.0
12.0
Q2
PACKAGE MATERIALS INFORMATION
www.ti.com
17-May-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TS12A12511DCNR
SOT-23
DCN
8
3000
202.0
201.0
28.0
TS12A12511DGKR
MSOP
DGK
8
2500
358.0
335.0
35.0
TS12A12511DRJR
SON
DRJ
8
1000
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated