TI UA79M05CKC

µ SLVS060K − JUNE 1976 − REVISED APRIL 2005
D 3-Terminal Regulators
D Output Current Up To 500 mA
D No External Components
D High Power-Dissipation Capability
D Internal Short-Circuit Current Limiting
D Output Transistor Safe-Area Compensation
µA79M05, µA79M08 . . . KTP PACKAGE
(TOP VIEW)
INPUT
µA79M05 . . . KC (TO-220) PACKAGE
(TOP VIEW)
INPUT
OUTPUT
INPUT
COMMON
OUTPUT
INPUT
COMMON
INPUT
µA79M05 . . . KCS (TO-220) PACKAGE
(TOP VIEW)
OUTPUT
INPUT
COMMON
description/ordering information
This series of fixed-negative-voltage integrated-circuit voltage regulators is designed to complement the
µA78M00 series in a wide range of applications. These applications include on-card regulation for elimination
of noise and distribution problems associated with single-point regulation. Each of these regulators delivers up
to 500 mA of output current. The internal current-limiting and thermal-shutdown features of these regulators
essentially make them immune to overload. In addition to use as fixed-voltage regulators, these devices can
be used with external components to obtain adjustable output voltages and currents, and also as the
power-pass element in precision regulators.
ORDERING INFORMATION
TJ
0°C to 125°C
VO(NOM)
(V)
−5
ORDERABLE
PART NUMBER
PACKAGE†
PowerFLEX (KTP)
Reel of 3000
µA79M05CKTPR
TO-220 (KC)
Tube of 50
µA79M05CKC
TO-220, short shoulder (KCS)
Tube of 20
µA79M05CKCS
TOP-SIDE
MARKING
µA79M05C
µA79M05C
A79M05C
−8
PowerFLEX (KTP)
Reel of 3000
µA79M08CKTPR
µA79M08C
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerFLEX is a trademark of Texas Instruments.
Copyright  2005, Texas Instruments Incorporated
! "#$ %!&
% "! "! '! ! !( !
%% )*& % "!+ %! !!$* $%!
!+ $$ "!!&
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
µ SLVS060K − JUNE 1976 − REVISED APRIL 2005
schematic
COMMON
4.5 kΩ
to 6.3 kΩ
1.7 kΩ
to 18 kΩ
OUTPUT
0.1 Ω
0.2 Ω
INPUT
Resistor values shown are nominal.
absolute maximum ratings over virtual junction temperature range (unless otherwise noted)†
Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 V
Operating virtual junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
package thermal data (see Note 1)
PowerFLEX (KTP)
High K, JESD 51-5
θJC
19°C/W
TO-220 (KC/KCS)
High K, JESD 51-5
17°C/W
PACKAGE
BOARD
θJA
28°C/W
19°C/W
θJP‡
1.4°C/W
3°C/W
NOTE 1: Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) − TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
‡ For packages with exposed thermal pads, such as QFN, PowerPAD, or PowerFLEX, θJP is defined as the thermal resistance between the die
junction and the bottom of the exposed pad.
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
µ SLVS060K − JUNE 1976 − REVISED APRIL 2005
recommended operating conditions
VI
Input voltage
IO
TJ
Output current
MIN
MAX
µA79M05C
−7
−25
µA79M08C
−10.5
−25
Operating virtual junction temperature
0
UNIT
V
500
mA
125
°C
electrical characteristics at specified virtual junction temperature, VI = −10 V, IO = 350 mA, TJ = 25°C
(unless otherwise noted)
µA79M05C
TEST CONDITIONS†
PARAMETER
Output voltage
VI = −7 V to −25 V,
Input voltage regulation
VI = −7 V to −25 V
VI = −8 V to −18 V
Ripple rejection
VI = −8 V to −18 V,
f = 120 Hz
Output voltage regulation
IO = 5 mA to 500 mA
IO = 5 mA to 350 mA
Temperature coefficient
of output voltage
IO = 5 mA,
Output noise voltage
f = 10 Hz to 100 kHz
IO = 5 mA to 350 mA
IO = 100 mA,
IO = 300 mA
TJ = 0°C to 125°C
TJ = 0°C to 125°C
MIN
TYP
MAX
−4.8
−5
−5.2
−4.75
−5.25
7
50
3
30
54
100
mV
−0.4
mV/°C
125
µV
1.1
Bias current
1
Bias current change
VI = −8 V to −18 V,
IO = 5 mA to 350 mA,
Short-circuit output current
VI = −30 V
mV
dB
60
50
Dropout voltage
V
50
75
TJ = 0°C to 125°C
UNIT
TJ = 0°C to 125°C
TJ = 0°C to 125°C
V
2
mA
0.4
0.4
140
mA
mA
Peak output current
0.65
A
† Pulse-testing techniques maintain TJ as close to TA as possible. Thermal effects must be taken into account separately. All characteristics are
measured with a 2-µF capacitor across the input and a 1-µF capacitor across the output.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
µ SLVS060K − JUNE 1976 − REVISED APRIL 2005
electrical characteristics at specified virtual junction temperature, VI = −19 V, IO = 350 mA, TJ = 25°C
(unless otherwise noted)
µA79M08C
TEST CONDITIONS†
PARAMETER
Output voltage
VI = −10.5 V to −25 V,
Input voltage regulation
VI = −10.5 V to −25 V
VI = −11 V to −21 V
Ripple rejection
VI = −11.5 V to −21.5 V,
f = 120 Hz
Output voltage regulation
IO = 5 mA to 500 mA
IO = 5 mA to 350 mA
Temperature coefficient
of output voltage
IO = 5 mA,
Output noise voltage
Dropout voltage
IO = 5 mA to 350 mA
IO = 100 mA,
IO = 300 mA
TJ = 0°C to 125°C
TJ = 0°C to 125°C
MIN
TYP
MAX
−7.7
−8
−8.3
−7.6
−8.4
8
80
4
50
V
mV
50
54
dB
59
90
160
mV
60
TJ = 0°C to 125°C
UNIT
−0.6
mV/°C
f = 10 Hz to 100 kHz
200
µV
IO = 5 mA
1.1
Bias current
1
Bias current change
VI = −10.5 V to −25 V,
IO = 5 mA to 350 mA,
Short-circuit output current
VI = −30 V
TJ = 0°C to 125°C
TJ = 0°C to 125°C
V
2
mA
0.4
0.4
140
mA
mA
Peak output current
0.65
A
† Pulse-testing techniques maintain TJ as close to TA as possible. Thermal effects must be taken into account separately. All characteristics are
measured with a 2-µF capacitor across the input and a 1-µF capacitor across the output.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
18-Mar-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
Lead/Ball Finish
MSL Peak Temp (3)
7704001HA
OBSOLETE
CFP
U
10
TBD
Call TI
Call TI
UA79M05CKC
OBSOLETE
TO-220
KC
3
TBD
Call TI
Call TI
UA79M05CKCE3
OBSOLETE
TO-220
KC
3
TBD
Call TI
Call TI
UA79M05CKCS
ACTIVE
TO-220
KCS
3
50
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
UA79M05CKCSE3
ACTIVE
TO-220
KCS
3
50
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
UA79M05CKTPR
OBSOLETE
PFM
KTP
2
TBD
Call TI
Call TI
UA79M05CKTPRG3
OBSOLETE
PFM
KTP
2
UA79M05CKVURG3
ACTIVE
PFM
KVU
3
UA79M05MUB
OBSOLETE
CFP
U
10
TBD
Call TI
Call TI
CU SN
Level-3-260C-168 HR
TBD
Call TI
Call TI
2500 Green (RoHS &
no Sb/Br)
UA79M08CKC
OBSOLETE
TO-220
KC
3
TBD
Call TI
Call TI
UA79M08CKTPR
OBSOLETE
PFM
KTP
2
TBD
Call TI
Call TI
UA79M08CKTPRG3
OBSOLETE
PFM
KTP
2
TBD
Call TI
Call TI
UA79M08CKVURG3
ACTIVE
PFM
KVU
3
CU SN
Level-3-260C-168 HR
2500 Green (RoHS &
no Sb/Br)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
UA79M05CKVURG3
PFM
KVU
3
2500
330.0
16.4
6.9
10.5
2.7
8.0
16.0
Q2
UA79M08CKVURG3
PFM
KVU
3
2500
330.0
16.4
6.9
10.5
2.7
8.0
16.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
UA79M05CKVURG3
PFM
KVU
3
2500
340.0
340.0
38.0
UA79M08CKVURG3
PFM
KVU
3
2500
340.0
340.0
38.0
Pack Materials-Page 2
MECHANICAL DATA
MPSF001F – JANUARY 1996 – REVISED JANUARY 2002
KTP (R-PSFM-G2)
PowerFLEX PLASTIC FLANGE-MOUNT PACKAGE
0.080 (2,03)
0.070 (1,78)
0.243 (6,17)
0.233 (5,91)
0.228 (5,79)
0.218 (5,54)
0.050 (1,27)
0.040 (1,02)
0.010 (0,25) NOM
0.130 (3,30) NOM
0.215 (5,46)
NOM
0.247 (6,27)
0.237 (6,02)
Thermal Tab
(See Note C)
0.287 (7,29)
0.277 (7,03)
0.381 (9,68)
0.371 (9,42)
0.100 (2,54)
0.090 (2,29)
0.032 (0,81) MAX
Seating Plane
0.090 (2,29)
0.180 (4,57)
0.004 (0,10)
0.005 (0,13)
0.001 (0,02)
0.031 (0,79)
0.025 (0,63)
0.010 (0,25) M
0.010 (0,25) NOM
Gage Plane
0.047 (1,19)
0.037 (0,94)
0.010 (0,25)
2°–ā6°
4073388/M 01/02
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
The center lead is in electrical contact with the thermal tab.
Dimensions do not include mold protrusions, not to exceed 0.006 (0,15).
Falls within JEDEC TO-252 variation AC.
PowerFLEX is a trademark of Texas Instruments.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated